Title(BLIND PAPER: DO NOT ADD AUTHORS AND/OR AFFILIATIONS)

Abstract

The abstract length is limited to 250 words. Ingegraf2019 conference aims to provide a special opportunity for the scientists to exchange their know-how and build up col-laboration in Advances on Design Engineering Each submission will be rigorously re-viewed and should be prepared with no references to the authors. All the accepted pa-pers will be published on Lecture Notes in Mechanical Engineering, a book edited by Springer and indexed in WoS, SCOPUS and SJR. The format of your paper is defined in this MS Word template and contains the prescribed styles necessary to be published by Springer. All papers must be submitted electronically in WORD format using the conference management system and following the instructions you find at http://29congreso.ingegraf.es

Keywords:   Please, indicate between three and five keywords, which will also be used for composing the Subject Index (written in 10 pt, justified).

1 Introduction

All papers should be restricted in length between 6 (minimum) and 10 (maximum) pages. Additional four (4) extra pages will be allowed with an extra fee of 10.00€ per page. We aim to produce conference proceedings of a professional and consistent quality. We will be grateful for your help by carefully following the instructions out-lined in this guide. This instruction itself is formatted as a Ingegraf2018 final paper. The font used in this Template is Times. Please, do not use other similar fonts.

Abstract is written in 10 pt, justified. Use abstract style.An example of the sections to be included in the manuscript could be the follow-

ing: introduction, materials and methods, results and discussion, conclusions, and ref-erences.

The title of the paper should be written in 16 pt bold, center-alignment. Use title style. Section titles are 12pt bold, alignment left and are heading1 style. Subsection ti-tles are 12pt bold italic, alignment left and heading2 style. Only two levels of head-ings should be numbered. Lower level headings remain unnumbered. The following standard numbering is prescribed: 2, 2.1, 2.2 etc. Instead of simply listing headings of different levels we recommend to let every heading be followed by at least a short passage of text.

2

The following are some examples of a typical equation, figure, table, citations and references. Please do not change the proposed formatting by introducing other styles or by changing this template.

1.1 Paragraphs and indents

Please note that the first line of text that follows a heading is indented (Text_first style), whereas the first lines of all subsequent paragraphs are (Text style). The text is 10 pt, justified. Spacing of the text is 12pt.

2 Equations

The same style as normal text (Text) should be used in equation. Here, however Sin-gle space is recommended. Equations should be centered and numbered (equation style). Figure 1 presents the styles and sizes for equations. They should be referenced in the text as, for instance, (1). An example of equation is as follows

(1)

3 Figures

Figures (at least 300 dpi) should be centered and referenced in the text as, for exam-ple, Figure 1. The font size used inside the figures should be as Normal text (10 pt). Captions are placed under the figure, written in 8.5pt, using figlegend style. The ex-ample follows.

3

Fig. 1. Equation formatting.

4 Tables

Tables should be centered and referenced in the text as, for example, Table 1. The font size in tables should be table style (8.5pt). Captions are placed before the table (tablelegend style).

Table 1. Please write your table caption here.

Description 1 Description 2 Description 3 Description 4

Row 1, Col 1 Row 1, Col 2 Row 1, Col 3 Row 1, Col 4Row 2, Col 1 Row 2, Col 2 Row 2, Col 3 Row 2, Col 4Row 3, Col 1 Row 3, Col 2 Row 3, Col 3 Row 3, Col 4

5 Referencing

For citations of references, we prefer the use of square brackets and consecutive num-bers [1, 2, 3, 4]. In the references section, a sample list is provided with entries for journal articles [1], an LNCS chapter [2], a book [3], proceedings without editors [4], as well as a URL [5]. Please, include the digital object identifier (DOI) for all refer -ences where available. Use references style (9 pt).

4

Acknowledgments

   The research work reported here was made possible by...

References

1. Author, F., Author, S.: Article title. Journal 2(5), 99–110 (2016).2. Author, F., Author, S.: Title of a proceedings paper. In: Editor, F., Editor, S. (eds.) CON-

FERENCE 2016, LNCS, vol. 9999, pp. 1–13. Springer, Heidelberg (2016). 3. Author, F., Author, S., Author, T.: Book title. 2nd edn. Publisher, Location (1999).4. Author, F.: Contribution title. In: 9th International Proceedings on Mechanical Engineer-

ing, pp. 1–2. Publisher, Location (2010).5. LNCS Homepage, http://www.springer.com/lncs, last accessed 2016/11/21.