TRAVEL & ACCOMMODATIONMill is 2 hours from Prince Albert, 2.5 hours from Saskatoon and 35 minutes from Meadow Lake, Sask, where the closest accommodation is. Meadow Lake has an airport (IATA: YLJ; ICAO: CYLJ; WMO 71125) with two asphalt runways, 5,000’ & 2297’. There are no facilities or car rentals at that airport. Closest full service airport is Saskatoon (YXE).

Hotels:Super 8 ........................................... (306) 236-1188Travelodge ...................................... (306) 236-8686 Four Seasons Motel ....................... (306) 236-4493Woodland Inn ................................ (800) 869-5705Nor’wester Motor Inn.................... (306) 236-4424

SAWMILL CLOSUREAUCTION!Green Lake SawmillWEDNESDAY, JUNE 5TH – 10AMGreen Lake, Sask.

• DEBARKER • HEADRIG • SCRAGG SAW • • SALEM EDGER • POCKET EDGER •

• CHIPPING • MORE...

T. 604.530.9351 E. info@tradewestsales.comwww.tradewestsales.com

Another Auction With Integrity By

TERMS OF SALE Payment: Full payment day of sale by wire transfer, cash, Debit, Visa, Mastercard or company cheque accompanied by bank letter unconditionally guaranteeing payment on presentation. Maximum $5,000.00 payment by credit card. Full payment by cleared funds must be made before removal of items purchased. Buyer’s Premiums will be added to all invoices as follows: On-site bidders – 15%; On-line bidders: 18%. All items in auction are subject to additions, deletions and prior sale. Majors Removal: All items must be removed from sale site by 4pm, Friday, July 5th, 2019.

All items are sold “as is – where is”, with all faults. While quantities and descriptions are believed to be accurate, the auctioneer, owner, employees or counsel make no warranties or guarantees either expressed or implied as to the authenticity, genuineness of, or defects in any lot, and will not be held responsible for any advertising discrepancies or inaccuracies. No warranties whatsoever are made as to condition, merchantability or fitness for any use of any item. Please take advantage of our preview and inspection period.

Another Auction With Integrity By

N

T. 604.530.9351 E. info@tradewestsales.comwww.tradewestsales.com

AUCTIONSITE

VOLUNTARY SAWMILL CLOSURE

GREEN LAKE SAWMILLAUCTION!

OF

WEDNESDAY, JUNE 5TH – 10AMPlace: HWY 55, Green Lake, Sask. • Preview: Tues. June 4th, 9AM – 4PM

CAMBIO 27’’ RING DEBARKER MORBARK S-48 CHIP PACK

INCLINE POCKET EDGER & INFEEDPHL TWIN SCRAGG SAW

REFORM 10L FLAT KNIFE GRINDER MODULAR 27” BULL EDGER

CONTAINER ELECTRICS

SALEM TWIN 40HP HPU

AIRTEK TW-400 AIR DRYERSULLAIR 100HP COMPRESSOR

20’ ELECTRICAL CONTAINER

SEVERAL MCC’S TO 7 SECTIONS

Listing subject to prior sales, additions and deletions without notice.

BID LIVE, REAL TIME, ON-LINE! REGISTER AT:

DEBARKER & LOG INFEEDCambio 75A 27” Debarker, S/N 66203; 75 HP 575V, Top & Bottom Tire Rolls; Control booth & controls; Waste Conveyor, 15” x 36’, flighted long link chain; 15HP ● 4 Run Log Transfer Deck, 27’L x 12’1”W, H78; 10 HP/Radicon ● Debarker Infeed Conveyor, 16” x 18’L; Flighted chain ● Belt Conveyor, 24”W x 21’6”L; 5HP 1725 RPM/Reducer ● Log Bunk, 11’W x 12’L ● 4 Run Log Transfer Deck, 18’7” x 24’6”L, H78B; 3 singulator arms; 15HP/Radicon #5 ● Spiked Hourglass Rollcase, 36”W x 60’ ; (19) Rolls; w/ 89’ x 36” grate steel catwalk, railing & stairs ● 6 Roll Hourgiass Rollcase, 30.5” x 25’; 15HP/Reducer ● Log Infeed Operator Console ● 4 Run Head Rig Infeed Transfer, 12’7” W x 16’6” ● Debarker Waste Conveyor, 15” x 62’; Flighted L/L chain; 10HP/Falk 74.48 Reducer

SAWMILLMorbark Circular Saw Head Rig, Modular; 4’6” Diameter Blade; 16’ 4 Bunk Carriage; 150HP; S/N 1274; Booth, controls & setworks; w/ 36” transfer to carriage; w/ (5) arm singulator; 10” x 9’ saw slab belt conveyor to outfeed belt, 20” x 20’L, spiked end roll ● 50HP Hydraulic Power Unit ● Allen-Bradley 3 Section, 2 Sided MCC ● PLC Cabinet ● Service Breaker Panel ● Marcus 40KVA transformer, 600-120/208V; PHL Horizontal Twin Scragg Saw, Model S 110, (2) 48” blades; S/N SJB 63 ER; 75HP; Spiked infeed & outfeed holddown rolls; 20” flat chain through feed; 10” x 10’6”L sharp chain outfeed; 2-1/2” chain; (2) 16” x 14’ Waste Belt Conveyors; Winged box chain waste conveyor below scragg, 18” x 40’L; 1’ X 5’ Outfeed Belt; Control booth ● 25HP Hydraulic Power Unit ● 20HP Hydraulic Power Unit ● Belt Conveyor, 18”W x 51’L; 7.5HP Reducer ● 5 Run Log Transfer Deck, 15’6”W x 38’L; H78B ● 5 Run Log Transfer Deck, 15’W x 22’L, H78B; 25 HP ● 6 Strand Unscrambler; 20’3” x 9’H Pyramid Flights ● Salem Gang Edger, S/N 91695, (2) 200 HP Drives; Temposonic optimization ● (5) Laser Guides ● 5 Run Transfer Deck, 16’W x 14’L; 10HP ● Double Edger Infeed Rollcase Transfer; (2) Runs 27” & 43” Splined Rolls x 19’6”L; Each run w/ (4) 30” & (4) 48” cross jump chains w/ air bags; feeds from both sides ● Belt Conveyor, 23’6”W x 10’6”L; O/H hydraulic lift cylinder ● 52” x 51’ Rollcase, 9 of 15 Rolls w/ Half Spiral; (6) Smooth rolls ● 5 Run Lumber Transfer Deck, 15’6”W x 28’L, H78B ● Edger Control Booth, 10’6” x 7’7” ● Edger & feed controls & PLC ● 7 Section MCC, 21 Full

Buckets ● HD Steel Protection Plate, front of edger booth, 6’H x 12’W ● All Catwalk, railings & stairs in edger area ● Salem Twin Hydraulic Power Unit, 2 x 40HP drives; 1170 RPM; w/ Thermal Transfer ● 20HP Hydraulic Power Unit; 1765RPM; w/ Thermal Transfer ● Air Receiving Tank, 3’ x 11’L ● Edger Lube System ● Slant Feed Pocket Edger, Single Arbor w/ (2) 24” Saws; 75HP 1780 RPM; w/ Slant Feed system & holddown system; w/ 7 Run Infeed Transfer, 8’6”L x 18’9”W; Sensor eyes; (4) Full width singulator bars; (2) sets knurled top feed rolls; 20’L Outfeed alternating board feeder onto two belts ● Adjustable Powered Knurled Pinch Rolls; 26”; w/ adjustable cylinder & drive ● Pocket edger Infeed Belt Conveyor, 12” x 18’L ● Drop-out Return Belt Conveyor, 17” x 82’L; 10HP/Radicon ● Pocket Edger Outfeed Belt Conveyor, 82’L Overall; Comprised of (2) Belts, 16” x 31’L & 11” x 51’; 10 HP ● 20 HP Hydraulic Power Unit & Reservoir ● Double Outfeed Rollcase Transfer, (2) Runs Of Side By Side Offset Rolls, 48”W x 19’6”L ● Trimmer Infeed Transfers: 5 Run Lumber Transfer Deck, 15’W x 2’L, H78B; end stop; steel deck; 10 HP 1765 RPM & Radicon ● 6 Run Lumber Transfer Deck, 15’W x 13’L, H78B; end stop & hyd. drop gate; 5 HP & reducer ● Operator Console ● 19’ Hydraulic Drop Gate & slide ● Return Belt Conveyor, 15” x 43’ ● 6 Run Lumber Transfer Deck, 17’6”W x 30’L, H78B; 10HP Motor, 1745 RPM; w/ Radicon 31:1 reducer ● 4 Section MCC ● Double Valley Trim Saw System, w/ (10) Run 40’L Transfer Deck, 20 HP, Left & Right Trim Saws, 3,500 RPM; H78; (8 Roll) 9’ Even ending roll line & (5 Roll) 24” Even ending roll line; w/ Infeed Line comprised of Board Unscrambler, 15’W x 7’6”H; w/ drive; 6 Run Lumber Transfer Deck, x 12’L, H78 Chain; w/ drive; 7 Run Lug Loader, 5’L ● (2) Waste Belt Conveyors Below Trim Stations, 36”W x 95’L; 10 HP, & 30”W x 30’L; 5HP ● 40HP Hydraulic Power Unit, w/ Thermal Transfer heat exchange ● Operator Console & PLC cabinet ● 5 Run Green Chain Transfer, 14’4”W x 132’L, H78B; (2) Runs plastic capped; Full length catwalk ● 25HP 1770 RPM/Radicon #6 60:1 ● 4 Run Green Chain Transfer, 12’10” x 49’L; C55A; (9) & 5 side rolls both sides; 5HP 1729 RPM; Radicon AU500B Reducer, 41:1 ratio ● Waste Conveyors: Main Mill Waste Conveyor, 16” x 214’L; Flighted; 20HP Motor & Reducer ● Incline Waste Belt Conveyor from Scragg; 18” x 60’; 10HP/Highfield U17163/03 40:1 Reducer ● Cross Waste Conveyor, 17” x 24’; Winged box chain; (Edger to Main); 7.5HP 1750RPM/SM-Cyclo Drive

CHIPPING & BINSIncline Waste Belt Conveyor, 16” x 18’L; flighted chain; 5HP Motor, 575V; w/ Highfield #5 30”1 Reducer ● Morbark S48 Chip Pack, 150 HP, w/ Chip Classifier/Screen & Cyclone ● 5 Run Lumber Transfer Deck, 19’W X 28’4”L, H78B; steel deck & catwalk; 15HP/Radicon #6 ● 26” x 16’ Rollcase, 8 rolls; 16” x 20’ long link waste conveyor below ● Quickdraft 136 50HP Blower ● Clarke CA-36 Air Lock ● (2) Peerless 16 Unit Sawdust Bins, (1) w/ Cyclone; Top Transfer Belt ● 5HP Hydraulic Power Unit ● 16” Diameter x 125’L Thick Wall Blower Pipe to Sawdust Bin ● Wigwam Burner, 30HP Blower, 56” x 24”; 1750 RPM/Honeywell controls ● 200’ Incline Chain Conveyor to Burner; S-chain; 15HP 1800 RPM/Renold #8 40:1 ● Allen-Bradley 3 Section MCC ● Operator Console

ELECTRICALAllen-Bradley BUL-2100 1200 Amp MCC; switches for edger drive ● FPE Main Breaker, 75H-2 600V 3 Pole; FR Size 3000; Relay 2500 ● 20’ Shipping Container & Electrics: w/ Cutler-Hammer 1200 Amp Main Switch; (2) FPE 600 Amp Switches; (2) 30 Amp, (2) 60 Amp & (4) 100 Amp Switches; Compressor switches, resets; AVI 300 KVA Transformer, 600-480V (as-is); Dresser 30KVA Transformer; 600-120/208V (As-is) ● Spare Motors: Toshiba 200HP, 880RPM 575V; 505UZ Frame ● GE 150HP, 1185RPM 575V; 447T ● Toshiba 150HP, 1770RPM 575V; 444T ● GE 125HP, 1175RPM 575V; 445TZ frame ● SM-Cyclo H3180 Drive; Input 17; Output 325; Torque 18,400 ● (18) Assorted 575V Motors to 75HP ● (7) Reducers to max size Radicon AU10 10;1 ● Asst’d Electrical Panels & Switches ● All Sawmill Teck Cable ● Spool of Aluminum Teck Cable ● Large quant. of fuses to FPE 500 amp etc.

GRINDING ROOMS & SHOPReform 10L Flat Knife Grinder, s/n 1941; 1020mm bed; w/ Beaver Transformer ● Armstrong 3-110C Stretcher Roll ● Salem Vertical Saw Guide Surface Grinder; 3/4HP 208/230/460V ● 26” Round Saw Anvil ● Anvil & Stand ● Salem Horizontal Press/Welder ● Michigan L50 Babbitt Pot; 230V ● Carolina BP5500 55 Ton Shop Press ● 5 Ton Rolling Gantry Crane; 9’L x 11’H ● MH-32C Pump, 3HP 115/230V 1Ph ● Krushel 5250 Welder ● Westward Drill Press ● Spare head saw, edger & trim saw blades

YARD EQUIPMENTNicholson A4 27” Debarker; s/n 240-08152; w/ Controls & Booth ● Nicholson Debarker Infeed ● Skid Mounted Modular 27” Edger; Infeed Rollcase, 28”x 10’; Outfeed Rollcase 25” x 12’; Control panel, turner, 5 Laser Lights; s/n 2031; 200HP 1185 RPM 575V; 27’ Waste chain conveyor ● Vibrating Conveyor, 24” x 130’ (in 40 sections) ● Sweed 16” Board Puller, rubber lined top roll ● Donaldson Torit Model 90 Dust Collector, 3HP ● (2) Kalmar Type Straddle Carriers ● Lumber Rack Wagon & Hitch ● Weldco U19A Hyd. Log Grapple ● Wasau 1036RB 10’ Snow Blade ● Forklift Boom ● 47” Forklift Forks ● Armstrong 1772 Circ. Saw Sharpener ● 7 Section MCC ● 5 Strand Chain Transfer, 18’ x 6.5’; (4) Hyd. kickers ● 4 Strand Chain Transfer, 10’5” x 20’ ● 5 Strand Chain Transfer, 18’ x 15’; w/ 2 Runs H78B ● 4 Strand Chain Transfer, 13’ x 24’ ● (2) Sections of hourglass rolls ● Rollcase w/ incline chain waste conveyor, chain, hourglass rolls ● Inland Foundry Bucking Saw ● More…

GENERALSullair 100HP Air Compressor, Model LS 16 ● Airtek Air Dryer, Model TW 400, S/N T02682-07B, 400 CFM ● DeVilbiss 15HP Air Compressor, 230/460V; 80 Gallon Tank ● Wayne 10HP Air Compressor, 220/440V; 80 Gallon Air Tank ● 75HP Hydraulic Power Unit, w/ (3) Vickers Pumps & (1) 75HP motor; Reservoir 5’ x 11’ x 2’H ● (4) Caloritech GN158CT Heater Fans ● Metal 2 door storage cabinet ● Spool of 3/4” Wire Rope, 6x26 RRL 1WRC ● Warehouse racking ● Hydraulic hoses & fittings ● Pumps, hydraulic cylinders, etc. ● Transfer Chain, Mill parts, chain pulleys, shafts, end rolls, etc, ● Steel horses

GANG EDGER SPLIT INFEED ROLLCASE

GANG EDGER SPLIT OUTFEED ROLLCASE

TRANSFERS TO TRIM LINE HEAD RIG OUTFEED ROLLCASE (2) GREEN CHAIN TRANSFERS 50HP BLOWER, AIR LOCK & 16” X 125’ BLOWER PIPE WIGWAM BURNER W/ BLOWER & 200’ INCLINE TRANSFER

(2) PEERLESS 16 UNIT CHIP BINS

SCRAGG OUTFEED BELT, 18’’ X 51’

INFEED TRANSFER TO SCRAGGMORBARK CIRCULAR HRAD RIG & CARRIAGEDOUBLE VALLEY TRIM SAW SYSTEMSALEM GANG EDGER