week 3 grinding

UNIVERSITI MALAYSIA PAHANGFACULTY OF MECHANICAL ENGINEERING

Grinding

1.0OverviewGrinding is generally considered to be a finishing operation. Possibilities include resharpening cutting tools, surface grinding of work fixtures and mold sections, inside diameter (ID) and outside diameter (OD) grinding of valve bodies, and many other potential applications. Grinding has many different applications in the machine tool industry. The grinding operation can be performed on a variety of machines such as the lathe and the mill - with the appropriate add-on accessories.

2.0Cutting ActionTo be successful with grinding, it is necessary to understand some basic principles. Grinding uses a method of material removal called abrasion. Rather than cutting like a lathe bit, the material is slowly worn away because the abrasive is harder than the material being ground. In truth the grinding wheel acts like many thousands of very small lathe bit, each cutting off some metal.The abrasive must also be strong enough to withstand the forces acting upon it while grinding. Usually some sort of impact shock occurs when the abrasive comes in contact with the material.Heat while grinding is of major concern, with effects seen at every phase of the operation. Also the abrasive needs to be able to

MECHANICAL LAB 2_ GRINDING 1


withstand high temperatures caused by the friction during the grinding. Sometimes, these high temperatures will cause damage to the bonding agents found in the wheel causing the wheel to break down. In general coolant must be directed at the grinding wheel, not the material being ground, as heat causes more damage to the wheel than the work piece.

Most abrasive wheels need to be able to be resurfaced (dressed), as the old surface will become impregnated with material during the grinding operation. Dressing is accomplished with a diamond tipped tool.

3.0Types of Grinding MachinesThe grinder is a machine that is used for fine surface finishing and the amount of material removed rarely exceeds a few thousands of an inch. These machines have been developed over the years to satisfy specific needs of the industry it serves, so grinding has become specialized, as has turning and milling. The most common types of grinders are the surface grinder, the universal tool and cutter grinder, and the cylindrical grinder.



4.0Surface Grinder



Surface grinding is probably the most fundamental of operations. Most shops have a surface grinder even if they don't have a universal cutter grinder of a cylindrical grinder. The basic machine has grinding wheel above the work area which can be fed downward in very small increments into a work piece which is being moved to the left and the right and in and out. This allows the wheel to contact all areas of the surface of the work piece. The grinder is usually equipped with a magnetic plate used to hold the work piece. It is sometimes referred to as a magnetic chuck, although it does not look anything like a lathe chuck. The magnetic chuck holds magnetic materials only. However steel clamps (a magnetic material) can be used to laterally clamp non-magnetic materials for surface grinding.

5.0Surface Grinder Feeding and CoolantThe surface grinder demonstrated in this topic has a hydraulic feeding system (figure 5.1) which actuates the table.

Figure 5.1

Left and right motion is governed by a set of dogs (figure 5.2) which can be set to limit the feeding distance.



Figure 5.2

Another set of dogs can be set to limit the in and out feeding distance (figure 5.3). The speed and distance offset for each move is governed by a set of bleeder valves in the hydraulic circuit (not shown)

Figure 5.3

Coolant for this grinder is fed, cleaned, cooled, and recirculated by a separate system (figure 5.4).



Figure 5.4



6.0OD Cylindrical GrindingThe three most common types of cylindrical grinding processes are OD, ID, and centerless.OD (Outside Diameter) grinding is performed between centers. The work piece has center drilled ends which accommodate center points and the work is rotated with a dog which is driven off the grinder's face plate.

In the graphic above note the rotation of the work piece and the grinding wheel. With OD grinding the work piece and the grinding wheel rotate in the same direction. This so that the surface of the grinding wheel and the surface of the workpiece are moving in opposite directions at the point of contact. This also reduces the possibility of ride-up or jamming that can occur if they were rotating in opposite directions.

7.0ID Cylindrical GrindingID (Inside Diameter) grinding is performed on tubular parts (with inside diameter) that are usually held in a collet or chuck. The grinding wheel is smaller than the hole to be ground and turns at very high speed to maintain the proper surface speed (compare the large wheel and small work piece of OD grinding on previous page).



The image on the above shows a typical small hole being ground by an even smaller mounted grinding wheel like one of those shown below

As with OD grinding the grinding wheel and the part need to be moving in opposite direction at the point of contact. Therefore this ID part will turn clockwise and the ID wheel will turn counterclockwise.



8.0CenterlessCenterless grinding is OD grinding performed on parts without centers and without any place to hold on to it (as with a chuck). Picture the rollers in a roller bearing or a dowel pin. There is nothing to hold on to.

On the centerless grinding machine the part actually rotates between a grinding wheel and a regulation wheel. The regulating wheel governs the rotation of the work piece. On many machines these types of parts are being ground continuously by being fed in one end and ground out the other end. It is vey fast.



9.0Universal Tool and Cutter GrinderThe universal tool and cutter grinder is used for almost any type of work required in the tool room. This machine is most often used to re-sharpen the different types of cutting tools found in the shop. It is not considered a very heavy-duty machine, so huge amounts of material removal should not be attempted at this machine.

The machine is equipped with four main components, the base, the wheel, the saddle and the table.There are many attachments used on the universal cutter grinder. These attachments make it possible to perform various types of sharpening. The right and left tailback and detachable motor make setups the most challenging part of working in a tool room.

Tool grinding requires a very thorough understanding of the geometry of the tool being ground. The grinds found on each cutter are

complex, to say the least. Each grind has a specific primary and secondary clearance angle for the type of material being cut.An efficient tool grinder will work far in advance of the production curve, providing more than the required number of tools for each production requirement, as a fail safe in case something should break. Coordination of the tool room with the production team is critical.Another important part of the universal cutter grinder is the type of grinding wheel that the grinder chooses to use in the grinding work to be performed. As this subject is quite detailed, it will be discussed in a different module of its own. (See Grinding Wheels).



10.0 Bench GrinderThe bench grinder (figure 10.1) or is found in every shop It is used for rough work and to grind tool bits made from high speed steel and carbide. Tool bit grinding is a standard skill expected of all journeyman machinists. Drill sharpening attachments are sometimes used on bench grinders (figure 10.2).

Figure 10.1 Figure 10.2

Some bench grinders have attachments for a special grinding processes like the wet grinder. The wet grinding wheel turns very slowly through a bath of oil or water. This type is suitable for blade sharpening. (figure 10.3)


Another special bench grinder is the cutter grinder used for more precise hand tool work. Diamond face wheels are sometimes attached for harder materials like carbide and ceramic. (figure 10.4)



11.0 Lapping and PolishingLapping is the process of using a grinding compound of free grit and oil to create very precise surfaces of high finish. Flat lapping machines are used to make small flat surfaced parts (figure 11.1).

Figure 11.1Polishing and buffing are also methods of grinding. The buffing compound (grit) is applied to buffing wheels (figure 11.2) that are mounted on special buffing grinders (figure 11.3)




12.0 Grinding Wheels

Grinding wheels have a huge responsibility in the manufacturing industry. From finishing parts to sharpening tools, grinding wheels are a common item found in all machine shops. Grinding wheels can usually be classified as natural or artificial, such as with a diamond wheel (natural) or a silicon carbide wheel (manufactured). This topic will explain the difference.Man has been using abrasives throughout history. The majority of natural abrasives, such as sand, emery and quartz, have been replaced by manufactured abrasives such as silicon carbide or aluminum oxide. Machinists use manufactured abrasives more often than natural abrasives.

13.0 Grinding Wheels MaterialThere are two main material types for grinding wheels: Aluminum Oxide and Silicon Carbide. Aluminum Oxide is used to grind materials such as hard steel, wrought iron and tough bronze. These materials are considered to have a high tensile strength. Depending on the purity factor, it can also be used to grind cast iron as well as stellite, which is used in dies and gages. Aluminum Oxide it the most common abrasive used in grinding wheels.Silicon carbide grinding wheels are used to grind low tensile strength materials, such as aluminum, brass and softer bronzes. It is also used on most non-ferrous metals.



Other specialty materials are Cubic Boron Nitride, diamond, and gel ceramic abrasive.



14.0 Grinding Wheels ShapesGrinding wheels come in various shapes. Each shape is selected to perform a specific job.

The cylindrical wheel is the most common type. Its cutting surface is located at the periphery of the wheel. Wheels of this shape are often mounted on a plate.The straight cup wheel is designed to cut on the periphery and the side face at the same time. This type of wheel is often used to grind shoulders.The dish wheel is a tool and cutter grinding wheel. It is typically used to regrind end mills and has a specific shape to accomplish that.The flared cup wheel is also tool and cutter grinding wheel. There are several cup shapes available depending on the needs of the machinist.Grinding wheels can be custom dressed with a diamond tool to achieve nearly any shape desired.



15.0 Grinding Wheels - How Abrasives WorkThe function of abrasives is to remove material. The wheel is made up of two components, the abrasive and the bond.The abrasive acts like the cutter and the bond is the glue holding the abrasive grains together.Since the abrasive is harder than the material being ground, each grain acts like a cutting tool.The size of the grain, like the size of any cutting tool, is an important consideration.

16.0 Grinding Wheels Grain and BondThere are six different ranges of grain, from very coarse to very fine. Grain sizes are selected according to the type of finish desired, the material being ground, and the amount of material being removed.If the grinder is performing a roughing operation, a course grain would be selected, providing maximum metal removal. Likewise, finer grains are used for minimum material removal and high surface finish requirements.The function of the bonding agent is to unite all of the abrasive grains into a wheel. There are six types of bonding agents: vitrified, Profilometer, rubber, shellac, silicate and metal. The vitrified type is used on most abrasives. In the resinoid bond, synthetic resins are used to unite the grains of the abrasive. A resinoid bonded wheel produces a higher surface finish, and should be run at a higher surface feet per minute than the vitrified bond

17.0 Grinding Wheels Grade



The grade of the wheel describes the strength of the union between grain and bond. It is desirable for the grains that have been worn down to break away, exposing new grains to the work surface. As this is accomplished, the old grains are released from the wheel. The bond is rated hard grade if the abrasive is released slowly, and the bond is difficult to break. The grade is graded soft if the bond breaks away easily, allowing rapid grain disintegration.Selecting the proper grade for the wheel is one of the more difficult choices to make in wheel selection.It is important to remember that all abrasive grains are hard, and that the hardness of the wheel refers to the strength of the bond, not the hardness of the grain.

18.0 Grinding Wheels StructureStructure refers to the microscopic spaces between the abrasive grains and the bond. If the spacing of the grains are close to each other, then the wheel is a densely structured wheel. If the structure of the spacing is relatively wide, then the wheel has an open structure. Open structure wheels have a greater ability to remove material than dense wheels.



19.0 Grinding Wheels IdentificationEach grinding wheel comes with a paper label glued to its face. The label provides much information concerning the composition of the wheel.

The system is a series of numbers and letters which codify the composition of the wheel. The first letter indicates the type of abrasive used, using the letter A for Aluminum Oxide or C for Silicon Carbide. Next the manufacturer of the wheel will indicate the grain size, with appropriate numbers indicating a coarse, medium, or fine range. The grade is indicated in alphabetical form, with the softest grade being the A end of the alphabet, and the Z being the hardest.Structure is indicated by a numerical rating, but its use is optional. Finally the bond type is indicated by an abbreviation of the type of bond used, V for vitrified, S for silicate, etc. Wheels sometimes have different colors and can be representative of the type of wheel. If the Norton Company is used as a reference, the following color codes would apply for the best materials and processes for each wheel:

White Aluminum Oxide - Used on tool steels and mold steels

Pink or Blue Aluminum Oxide - Used on alloyed tool steels

Off-White/Light Grey Monocrystalline Aluminum Oxide - Better for holding than the above, used on high speed steels as well



Light Blue Synthetic Aluminum Oxide - Works on all ferrous materials, used in high production applications

Gray Mixed Aluminum Oxide - Used on centerless or cylindrical applications

Green Silicon Carbide - Used on non-ferrous materials such as aluminum and carbide tooling.



20.0 Grinding Wheels SafetyThere are several safety issues that a machinist needs to be concerned with when dealing with grinding wheels. Mainly, grinding wheels can crack. Most machines have safety guards to deal with this problem, but keep in mind that a shattered wheel can injure the machinist as well as the people working nearby. Various conditions can create this problem such as excessive depth of cut, poorly balanced wheels, damaged wheels, or improper assembly on the machine. It is best to keep grinding wheels stored in an area that is dry and enclosed to avoid object or liquid contact with the wheels.

It is also a good idea to conduct a ring test on a grinding wheel prior to using it. A ring test can locate an invisible crack. To perform this test let the inside diameter of the wheel rest on one finger of your hand and then gently tap the wheel with the plastic handle of a screw driver or wooden handle of a hammer. If you hear a clear metallic ring, the wheel is probably in good shape. If the wheel is cracked the ring will be somewhat dull and muffled


week 3 grinding

Documents

universal

cutter grinding

universal

bench grinders

cutter grinder

feeding distance

aluminum oxide

od grinding