welding presenttion part 1
TRANSCRIPT
![Page 1: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/1.jpg)
ETA Engineering. Pvt Ltd
A PRESENTATION ON WELDING TECHNIQUE
![Page 2: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/2.jpg)
Welding Technique Used
For Chilled Water Piping is
SMAW[ Shielded Metal Arc Welding]
![Page 3: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/3.jpg)
SMAW• Shielded Metal Arc Welding : - This method is the most familiar
and common type and is known in the trade as stick welding. A metal wire rod coated with a welding flux is clamped in an electrode holder connected to the power supply with a heavy electrical cable. The metal to be welded is also attached to the power supply. The electric power is supplied to the work at a low voltage and high current and may be either AC or DC, depending upon the type of welding being done. An arc is struck between the rod and the work and produces heat in excess of 10,000deg F, Which melts both the material and the rod. As the flux melts, it releases an inert gas which shields the molten puddle from oxygen in the air and prevents oxidization. The molten flux covers the weld and hardens to an airtight slag cover that protects the weld bead as it cools. This slag must be chipped off to examine the weld.
![Page 4: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/4.jpg)
• Why use welding?Welding is used because it is:
• One of the most cost-effectivemethods of joining metalcomponents.
• Suitable for thicknesses rangingfrom fractions of a millimeter to athird of a meter.
• Versatile, being applicable to awide range of componentshapes and sizes.
![Page 5: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/5.jpg)
Welding Positions
• 1G• 2G• 5G• 6G
• 1F• 2F• 2FR• 4F• 5F
![Page 6: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/6.jpg)
1G Position
Pipe rotated, Electrode is always at the top
Either a split bead or weave technique may be used
PIPE TO PIPE WELDING
![Page 7: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/7.jpg)
2G Position
Pipe Axis Vertical, Weld is Horizontal, Pipe is considered in a “fixed” position.
Always use a split bead technique
Always work from the bottom up.
PIPE TO PIPE WELDING
![Page 8: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/8.jpg)
5G Position
Axis of the Pipe is Horizontal, The weld in vertical.
Progression may be up or down.
A weave bead is best used.
PIPE TO PIPE WELDING
![Page 9: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/9.jpg)
6G Position
Pipe axis is fixed in position at a 45 degree incline. The position includes flat, horizontal, vertical, and overhead welds.
A split bead technique is best used.
PIPE TO PIPE WELDING
![Page 10: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/10.jpg)
1F Position
Pipe is rotated. The pipe axis is at a 45 degree incline. Welding is to occur at the top of the pipe.
Split bead or weave technique may be used.
PIPE TO PLATE WELDING
![Page 11: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/11.jpg)
2F Position
Fixed Position
Best to use a split bead technique
PIPE TO PLATE WELDING
![Page 12: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/12.jpg)
2FR Position
Rotated
A split bead technique is best used.
PIPE TO PLATE WELDING
![Page 13: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/13.jpg)
4F Position
A split bead technique is best used
PIPE TO PLATE WELDING
![Page 14: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/14.jpg)
5F Position
Not Rotated. Progression may be up or down.
Split beads or weaves can be used on 5F-up welds, split beads are best used on 5F-down welds.
PIPE TO PLATE WELDING
![Page 15: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/15.jpg)
75-800 Face angle1-2 mm Root gap1.0 mm land
Butt Joint Preperation
1.0 mm
(Joints without backing)
![Page 16: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/16.jpg)
Root Pass Hot Pass
Fill Pass Cover Pass
![Page 17: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/17.jpg)
Always work from the bottom up when using the split bead technique
Always be careful not to create a tight area where slag may get trapped under the next weld.
It is better to weave slightly than to leave a tight area.
Plan your sequence of beads!
![Page 18: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/18.jpg)
Always work toward the smaller side of the fillet. (It will be easier to get to)
Always be careful not to create a tight area where slag may get trapped under the next weld.
It is better to weave slightly than to leave a tight area.
Plan your sequence of beads!
![Page 19: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/19.jpg)
Techniques• Stringer (push, drag, or whip), or Weave
![Page 20: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/20.jpg)
Progression (vertical)
• Up (Electrode is moved from Down to top)– deeper penetration – Higher deposit rate (lb/hr)– Use near 90 degree travel angle or slightly up
• Down (Electrode is moved from Top to Down)– faster (point to point)– less penetration for thin metal– less dilution– Use steep drag angle
![Page 21: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/21.jpg)
TYPES OF DEFECTS OBSERVED IN WELDING
• Porosity• Pin hole• Cracks• Undercut• Lack of Fusion• Lack of Penetration• Slag Inclusion• Excess Penetration
![Page 22: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/22.jpg)
TYPES OF TESTING DONE ON WELD JOINT
• D.P.T (Dye Penetrant Testing)• M.P.T (Magnetic Particle Testing)• U.T (Ultrasonic Testing)• R.T (Radiography Testing)
NOTE: THESE TESTING ARE KNOWN AS NON - DESTRUCTIVE TESTING.
![Page 23: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/23.jpg)
CARE TO BE TAKEN BEFORE WELDING
1. Check the joint for proper ‘V’ groove .
2. Remove The Mill Scale Or Rust By Buffing Or Wire Brushing The Surface.
3. Ensure the joint is dry, there should be no moisture content on or near the joint surface.
4. Ensure the electrode used for welding is fully dry.
CARE TO BE TAKEN AFTER WELDING
1. Proper cleaning should be done after welding to remove slag & spatters.
![Page 24: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/24.jpg)
Final Pass after Root Pass
![Page 25: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/25.jpg)
![Page 26: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/26.jpg)
Machine settings. You will need to make adjustments depending on how thick the metal is, electrode diameter, and type of electrode.
Note: Machine settings of Amps & Voltage will be given on welding electrode cover.
![Page 27: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/27.jpg)
![Page 28: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/28.jpg)
FOLLOWING ARE SOME OF THE SNAPS OF GOOD & DEFECTIVE WELDING
![Page 29: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/29.jpg)
Snap taken at the root side of the weld joint. (Inside the pipe)
Excess penetration is observed
![Page 30: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/30.jpg)
Snap taken at the root side of the weld joint. (Inside the pipe)
Lack of penetration is observed.This occurs due to less root gap provided in the weld joint.
![Page 31: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/31.jpg)
Under cut observedThis is due to High current used during welding
Porosity observedThis occurs due to moisture content in the electrode or near the weld joint or due to welder lack of performance
![Page 32: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/32.jpg)
IMPROPER BEADING OBSERVED(THIS IS DUE TO WELDER LACK OF PERFORMANCE)
SPATTERS OBSERVED
![Page 33: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/33.jpg)
SPATTERS OBSERVED
![Page 34: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/34.jpg)
Snap taken at the root side of the weld joint. (Inside the pipe)
Excess penetration is observed
![Page 35: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/35.jpg)
Lack of penetration is observed.
This occurs due to less root gap provided at the joint During fitup.
Snap taken at the root side of the weld joint. (Inside the pipe)
![Page 36: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/36.jpg)
Porosity observed
This occurs due to moisture content in the electrode or near the weld joint, or due to welder lack of performance
![Page 37: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/37.jpg)
Porosity Observed
Under cut observed
This is due to High current used during welding
![Page 38: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/38.jpg)
SPATTERS OBSERVED
IMPROPER BEEDING OBSERVED
(THIS IS DUE TO WELDER LACK OF PERFORMANCE)
![Page 39: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/39.jpg)
SPATTERS OBSERVED
![Page 40: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/40.jpg)
IMPROPER BEEDING IS OBSERVEDSLAG INCLUSION IS OBSERVED
BOTH THE DEFECT WILL OCCUR DUE TO LACK OF WELDER PERFORMANCE.
![Page 41: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/41.jpg)
GOOD WELDING
![Page 42: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/42.jpg)
GOOD WELDING, But surface cleaning to be done.
![Page 43: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/43.jpg)
GOOD WELDING
![Page 44: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/44.jpg)
GOOD WELDING
![Page 45: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/45.jpg)
GOOD WELDING, But surface cleaning & Spatters to be removed.
![Page 46: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/46.jpg)
GOOD WELDING
![Page 47: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/47.jpg)
GOOD WELDING
![Page 48: WELDING PRESENTTION PART 1](https://reader033.vdocuments.net/reader033/viewer/2022061123/5473d01db4af9f266b8b45ba/html5/thumbnails/48.jpg)
GOOD WELDING