wellsford cabinetry door manual v3 print
TRANSCRIPT
DOOR STYLE SELECTION GUIDE
Mortise & Tenon Designwith cutdown rails
Miter design with equal, but reduced framing size
Thank you for considering Wellsford Cabinetry. This Door Selection Guide will provide usefulinformation on offering, price level, minimum sizing, and dimensional details for our standard doors. While we have selected 42 of the most popular doors, others are available to suite specific needs. Should you be in a position of having to match something particular, please let us know and we willshow you what we can do to fill your requirements.
All doors are available in Red Oak, Soft Maple, Hard Maple, and Cherry. Please refer to the FinishLibrary for available finishes. Other wood species are available on an as needed basis. All door stylesare available in 1/2" standard overlay. Other overlays and insets are available as noted on theavailability chart for each door.
Please notice that the minimum size of each door is different. Minimum sizing is critical when 9" baseand wall cabinets are necessary in a design. You will find notes on how each door is handled on a 9"cabinet, and in some cases it is not available. In general, we try to hold the stile size of the standarddoor and vary the left to right overlay.
Inset and beaded inset is available on most mortise & tenon door styles. Please refer to theAvailability Chart for each door. Inset doors use the same edge profile as shown here:
Inset doors and drawer heads are sized to leave a 3/32" gap between the edge of the door and theface frame, and between butt door pairs. You will be asked to select the Inset Hinge Color. You maywish to have the hinges match the decorative hardware used in the kitchen. If so, matchingdecorative hardware is available from Wellsford Cabinetry.
You will see that some door pictures show a drawer head and others do not. Each door style isavailable with a standard drawer head shown in the back of this Selection Guide. Upgraded 5 piecedrawer heads are available for most door styles, and these are also shown. In some cases thematching drawer heads are not available in 3/8" Inset. An example of this would be the Brighton orHastings designs. In any case, 5 piece drawer heads are not recommended in Inset styles due to thesmall height of the top drawers and the resulting height of the center panel of the drawer. We suggestusing a combination of matching drawer heads and Slab, Hastings, or Brighton for all 5" high drawersin Inset applications. Usually, the mitered 5 piece drawer head framing is smaller in width than thedoor framing, and the center panel is a flat panel. Mortise & Tenon styles will have stiles that are thesame size as the standard door stile, but the top and bottom rails will be cut down in height.
Face
5 degree back bevel
2 5/16"
Page 1
www.wellsfordcabinetry.com
N
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
NASTORIA
ALEXANDRIA
PI
N N N NBI 3/8 I F/O MDH RAD SHP CH ARPV
LEVEL 1
LEVEL 1
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset. Standard Overlay will use full size stiles, butthe overlay will be larger and a concealed hinge will be used.
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
Mortise & Tenon DoorPlain Inset and Beaded Inset not availableif Miter Design Option is selected.
Minimum size 7 1/2" x 7 1/2"
This is a veneer door with a hardwood edge.MUST SELECT HORIZONTAL OR VERTICAL GRAIN FROMCUSTOM OPTION.Contemporary style.Door faces use Grade A veneer, backs use Grade 1 or 2.A matching drawer head is always used.Sequenced or book matched doors not available.Glass doors will be Quaker style, stiles to be vertical grain, rails tobe horizontal grain.COLORTONE FINISHES ARE NOT AVAILABLE.
Minimum size 2 1/2" x 7"
2 5/16"
2 5/16"
Page 2
www.wellsfordcabinetry.com
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset. Standard Overlay will use full size stiles, butthe overlay will be larger and a concealed hinge will be used.
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PIRICHMOND
SPRINGFIELD
BI 3/8 I F/O MDH RAD SHP CH ARPV
LEVEL 1
LEVEL 1
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
Mortise & Tenon DoorPlain Inset and Beaded Inset not availableif Miter Design Option is selected.
Minimum size 7 1/2" x 7 1/2"
Mortise & Tenon DoorPlain Inset and Beaded Inset not availableif Miter Design Option is selected.
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset. Standard Overlay will use full size stiles, butthe overlay will be larger and a concealed hinge will be used.
2 5/16"
2 5/16"
Page 3
www.wellsfordcabinetry.com
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PIPROVIDENCE
COLUMBUS
BI
N
3/8 I F/O MDH RAD SHP CH ARPV
N
N
LEVEL 1
LEVEL 1
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
Mortise & Tenon DoorPlain Inset and Beaded Inset not availableif Miter Design Option is selected.
Minimum size 7 1/2" x 7 1/2"
Mortise & Tenon DoorPlain Inset and Beaded Inset not availableif Miter Design Option is selected.
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset. Standard Overlay will use full size stiles, butthe overlay will be larger and a concealed hinge will be used.
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset. Standard Overlay will use full size stiles, butthe overlay will be larger and a concealed hinge will be used.
2 5/16"
2 5/16"
Page 4
www.wellsfordcabinetry.com
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PI BI 3/8 I F/O MDH RAD SHP CHANNAPOLIS
AUGUSTA
NARPV
LEVEL 1
LEVEL 1
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
Mortise & Tenon DoorPlain Inset and Beaded Inset not availableif Miter Design Option is selected.
Minimum size 7 1/2" x 7 1/2"
Mortise & Tenon DoorPlain Inset and Beaded Inset not availableif Miter Design Option is selected.
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset. Standard Overlay will use full size stiles,but the overlay will be larger and a concealed hinge will be used.
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset. Standard Overlay will use full size stiles, butthe overlay will be larger and a concealed hinge will be used.
2 5/16"
2 5/16"
Page 5
www.wellsfordcabinetry.com
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PI BI 3/8 I F/O MDH RAD SHP CH ARPVWASHINGTON
OLYMPIA
N NN N
LEVEL 1
LEVEL 1
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
Mortise & Tenon DoorPlain Inset and Beaded Inset not availableif Miter Design Option is selected.
Minimum size 7 1/2" x 7 1/2"
Mortise & Tenon DoorPlain Inset and Beaded Inset not availableif Miter Design Option is selected.
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles inInset and Standard Overlay. The edge profile does not allowfor 3/8" Inset rabbeting, or concealed hinge boring.
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset. Standard Overlay will use full size stiles, butthe overlay will be larger and a concealed hinge will be used.
2 5/16"
Page 6
www.wellsfordcabinetry.com
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PI BI 3/8 I F/O MDH RAD SHP CH ARPVQUAKER
LEVEL 1
LEVEL 1 DESIGN OPTION
CATHEDRALN N N
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
This is a Design Option for all Level 1 doors except for Astoria, Stockholm, and Amesbury.The pictured door is an Alexandria.Select this door on the Order Front.Cathedral will apply to wall cabinets and tops of tall cabinets.
Minimum size 8 1/4" x 9 1/4"
Mortise & Tenon DoorPlain Inset and Beaded Inset not availableif Miter Design Option is selected.3/8" Inset door edge changes from 1/8" to 3/16" radius
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset. Standard Overlay will use full size stiles, butthe overlay will be larger and a concealed hinge will be used.
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset. Inset will also require the face frame stiles to be reduced to 1 1/4". Standard Overlay will use full size stiles, but the overlay will be larger and a concealed hinge will be used.
Page 7
www.wellsfordcabinetry.com
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PI BI 3/8 I F/O MDH RAD SHP CH ARPV
LEVEL 1DESIGN OPTION
LEVEL 1DESIGN OPTION
N N N
N N N
ARCH
MITER
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
This is a Design Option for all Level 1 doors except for Astoria, Stockholm, and Amesbury.The pictured door is a Richmond.This option is commonly used to eliminate the end grain on the stiles.Select this option on the Order Front.
Minimum size 7 1/2" x 7 1/2"
This is a Design Option for all Level 1 doorsexcept for Astoria, Stockholm, and Amesbury.The pictured door is a Washington.Select this door on the Order Front.Arch will apply to wall cabinets and tops of tall cabinets.
Minimum size 8 1/4" x 8 1/2"
NN
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset. Inset will also require the face frame stiles to be reduced to 1 1/4". Standard Overlay will use full size stiles, but the overlay will be larger and a concealed hinge will be used.
9" base and wall cabinet not available in 3/8" Inset.Standard Overlay will use full size stiles, but the overlay will belarger left to right, and a concealed hinge will be used.
BATTEN ON BACK OF DOOR
Page 8
www.wellsfordcabinetry.com
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PI BI 3/8 I F/O MDH RAD SHP CH ARPVHL-20 / HR-20
LEVEL 1DESIGN OPTION
N N N
STOCKHOLM
LEVEL 1
N N N N
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
This is a Design Option for all Level 1 doors except for Astoria, Stockholm, and Amesbury.The pictured door is a Washington.Right hand door shown (HR-20)Add these doors through a modification.
Minimum size 8 1/4" x 9"
This is a flat solid wood door.Battens on back are fixed 3" from top and bottom, and 1 7/8" infrom left and right edges.
Minimum size 6" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset. Inset will also require the face frame stiles to be reduced to 1 1/4". Standard Overlay will use full size stiles, but the overlay will be larger and a concealed hinge will be used.
2 5/16"
2 3/4"
Page 9
www.wellsfordcabinetry.com
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PI BI 3/8 I F/O MDH RAD SHP CH ARPVAMESBURY
LEVEL 1
SHAKER
LEVEL 2
N
N
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
This Mortise & Tenon door works well as a Shaker or Contemporary Style.3/8" Inset door edge changes from 1/8" to 3/16" radius.Grooved Center Panel available as custom option. Spacingwill match the beaded side and beaded back option (1 1/2").
Minimum size 7 1/2" x 7 1/2"
This is a traditional wide stile and railMortise & Tenon Shaker Door.3/8" Inset door edge changes from 1/8" to 3/16" radius.
Minimum size 8 7/8" x 8 7/8"
N
N
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset. Standard Overlay will use full size stiles, butthe overlay will be larger and a concealed hinge will be used.
9" base & wall cabinets not available in Inset,3/8" Inset, standard overlay, or full overlay.
2 3/4"
2 3/4"
Page 10
www.wellsfordcabinetry.com
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PI BI 3/8 I F/O MDH RAD SHP CH ARPVMONROE
FRANKLIN
LEVEL 2
LEVEL 2
N
N
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
This Mortise & Tenon door makes a bold statement with its wide stiles and rails.
Minimum size 9" x 9"
This Mortise & Tenon door makes a bold statement with its wide stiles and rails.
Minimum size 8 7/8" x 8 7/8"
9" base & wall cabinets not available in Inset,3/8" Inset, standard overlay, or full overlay.
9" base & wall cabinets not available in Inset,3/8" Inset, standard overlay, or full overlay.
2 5/16"
2 5/16"
Page 11
www.wellsfordcabinetry.com
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PI BI 3/8 I F/O MDH RAD SHP CH ARPVSAVANNAH
LEVEL 3
CHARLESTON
LEVEL 3
N N N
N N N
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
Mitered Door
Minimum size 7 1/2" x 7 1/2"
Mitered Door
Minimum size 7 1/2" x 7 1/2"
N
N
9" base and wall cabinet not available in 3/8" Inset.Standard Overlay will use full size stile, but the overlay will belarger left to right, and a concealed hinge will be used.
9" base and wall cabinet not available in 3/8" Inset.Standard Overlay will use full size stiles, but the overlay will belarger left to right, and a concealed hinge will be used.
2 5/16"
2 5/16"
Page 12
www.wellsfordcabinetry.com
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PI BI 3/8 I F/O MDH RAD SHP CH ARPVBRUSSELS
LEVEL 3
PRESTWICK
LEVEL 3
N N N
N
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
Mitered DoorContemporary Style
Minimum size 6 3/4" x 6 3/4"
Mortise & Tenon door with panel grooves 2" on center.Grooving is centered in panel.Does not match groove spacing on beaded sides or backs.Use Amesbury with Panel Grooving Option for a match.3/8" Inset door edge changes from 1/8" to 3/16" radius.
Minimum size 7 1/2" x 7 1/2"
N
N
9" base & wall cabinets in 3/8" Inset will have cut down stiles.Standard overlay will use full size stiles on 1/2" overlay withKnife or concealed hinges.
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset. Standard Overlay will use full size stiles, butthe overlay will be larger and a concealed hinge will be used.
2 5/16"
2 5/16"
Page 13
www.wellsfordcabinetry.com
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PI BI 3/8 I F/O MDH RAD SHP CH ARPVEMMITSBURG
LEVEL 3
LEVEL 4
SHELDON
NN N
N N
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
Mitered Door
Minimum size 7 1/2" x 7 1/2"
N
Mortise & Tenon doorCabinet must be minimum of 15" wide in standard overlay, 12" widein full overlay, to have a 2-panel door. Cabinets not meeting thewidth minimum will have a 1-panel door.3/8" Inset door edge changes from 1/8" to 3/16" radius.
Minimum size 11 3/8" x 6 3/4"
N
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset. Standard Overlay will use full size stiles, butthe overlay will be larger and a concealed hinge will be used.
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset. Standard Overlay will use full size stiles, but the overlay will be larger and a concealed hinge will be used.
2 5/16"
2 5/16"
Page 14
www.wellsfordcabinetry.com
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PI BI 3/8 I F/O MDH RAD SHP CH ARPVMADISON
LEVEL 4
AUSTIN
LEVEL 4
N
N
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
Mortise & Tenon door3/8" Inset door edge will change from 1/8" to 3/16" radius.
Minimum size 6 7/8" x 6 7/8"
Mortise & Tenon door
Minimum size 7 1/2" x 7 1/2"
N
NN
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset.
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset. Standard Overlay will use full size stiles, but the overlay will be larger and a concealed hinge will be used.
2 7/8"
2 7/8"
Page 15
www.wellsfordcabinetry.com
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PI BI 3/8 I F/O MDH RAD SHP CH ARPVPROVENCAL
LEVEL 4
PROVENCAL FLAT
LEVEL 4
N N N
N N N
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
Mitered Door
Minimum size 8 5/8" x 8 5/8"
Mitered Door
Minimum size 8 5/8" x 8 5/8"
N
N
9" base & wall cabinets are not available in 3/8" Inset.Standard Overlay and Full Overlay will use full size stiles, but the overlay will be 1 3/8" and a concealed hinge will be used.
9" base & wall cabinets are not available in 3/8" Inset.Standard Overlay and Full Overlay will use full size stiles, but the overlay will be 1 3/8" and a concealed hinge will be used.
2 15/16"
2 7/8"
Page 16
www.wellsfordcabinetry.com
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PI BI 3/8 I F/O MDH RAD SHP CH ARPVOLD FORGE
LEVEL 4
PRESTIGE
LEVEL 4
N N N N
N N N N
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
Mitered Door
Minimum Size 8" x 8"
Mitered Door
Minimum size 7 7/8" x 7 7/8"
N
N
9" wall & base cabinets in standard overlay will have a 1" overlayleft and right, and a concealed hinge will be used.
9" wall & base cabinets in standard overlay will have a 1"overlay left and right, and a concealed hinge will be used.
2 5/16"
3 3/8"
STILESECTION
RAILSECTION
2 1/2"
Page 17
www.wellsfordcabinetry.com
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PI BI 3/8 I F/O MDH RAD SHP CH ARPV
LEVEL 4
COPENHAGEN
LEVEL 5
N N
Mitered DoorContemporary Style
Minimum size 7 1/8" x 7 1/8"
N N
9" base & wall cabinets not available in 3/8" Inset.Standard Overlay will use full size stiles, but the overlay will be larger and a concealed hinge will be used.
N
Mortise & Tenon DoorUses 10141 or Slab Drawer Heads.
Minimum size 8" x 10 1/8"
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
N
NN
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset. Inset will also require the face frame stiles to be reduced to 1 1/4". Standard Overlay will use full size stiles, but the overlay will be larger and a concealed hinge will be used.
KINGSTON
2 15/16"
2 15/16"
Page 18
www.wellsfordcabinetry.com
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PI BI 3/8 I F/O MDH RAD SHP CH ARPVMILAN
LEVEL 5
LEVEL 5
N N N N
N N N N
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
Mitered DoorContemporary Style
Minimum size 7 1/2" x 7 1/2"
Mitered DoorContemporary Style
Minimum size 7 1/2" x 7 1/2"
N
N
9" base & wall cabinets in Standard Overlay will use full size stiles, but the overlay will be larger and a concealed hinge will be used.
9" base & wall cabinets in Standard Overlay will use full size stiles, but the overlay will be larger and a concealed hinge will be used.
MILAN FLAT
3 7/8"
2 5/16"
Page 19
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PI BI 3/8 I F/O MDH RAD SHP CH ARPVMIRAGE
LEVEL 5
LEVEL 5
OXFORD
N N N N
Mortise & Tenon DoorHardware space is limited on a matching drawer front. In an Inset, Standard Overlay, or Full Overlay applicationHastings or Brighton Drawer Heads offer more space whilecomplimenting the applied molding door style.Hastings & Brighton Drawer Heads are not available in 3/8 Inset.
Minimum size 7" x 6 3/4"
N
Mitered DoorSimulates Alexandria Door in Beaded InsetWorks well as Fully Integrated appliance panelfor Beaded Inset Alexandria Door style.AVAILABLE IN FULL OVERLAY ONLY.
Minimum size 10 5/8" x 10 5/8"
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
N
N
9" wall & base cabinets are not available.
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset.
www.wellsfordcabinetry.com
www.wellsfordcabinetry.com
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PI BI 3/8 I F/O MDH RAD SHP CH ARPV
2 11/16"
Page 20
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
DOVER
MODENA
LEVEL 5
LEVEL 5
Mortise & Tenon DoorMiter Option AvailablePlain Inset and Beaded Inset not availableif mitered option is selected
Minimum Size 7 1/2" x 7 1/2"
N
Mitered Door
Minimum Size 7 3/4" x 7 3/4"
9" base & wall cabinets are not available in 3/8" Inset, BeadedInset, or Plain Inset. Standard Overlay and Full Overlay will use 1 1/4" overlay.
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset. Standard Overlay will use full size stiles, butthe overlay will be larger and a concealed hinge will be used.
N
N N N NNN
2 5/16"
2 5/16"
2 3/4"
Page 21
www.wellsfordcabinetry.com
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PI BI 3/8 I F/O MDH RAD SHP CH ARPVCORNWALL
CHURCHILL
LEVEL 5
LEVEL 6
NNN
N
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
Mortise & Tenon DoorDecorative Applied Molding in door frame3/8" Inset door edge changes from 1/8" to 3/16" radius.
Minimum size 7 1/2" x 7 1/2"
Mortise & Tenon DoorApplied Molding on top of door frame3/8" Inset door edge changes from 1/8" to 3/16" radius.
Minimum size 8 7/8" x 8 7/8"
N
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset. Standard Overlay will use full size stiles, but the overlay will be larger and a concealed hinge will be used.
9" base & wall cabinets are not available in this door style.
www.wellsfordcabinetry.com
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PI BI 3/8 I F/O MDH RAD SHP CH ARPV
3 3/8"
3 3/8"
Page 22
AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
Mortise & Tenon DoorMiter not available
Minimum Size 9 5/8" x 9 5/8"
9" base and wall cabinets are not available.
Mortise & Tenon DoorMiter not available
Minimum Size 9 5/8" x 9 5/8"
9" base and wall cabinets are not available.
BARCELONA
BARCELONA FLAT
LEVEL 6
LEVEL 6
N N
NN
2 7/8"
Page 23
www.wellsfordcabinetry.com
BI 3/8 I F/O MDH RAD SHP CHPI ARPV
PI BI 3/8 I F/O MDH RAD SHP CH ARPVLASALLE
BAHAMA
LEVEL 6
LEVEL 9AVAILABILITY CODESPI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front PanelBI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance
Mortise & Tenon Door2 5/16" Stiles and Top RailBottom Rail varries from 2 1/8" to 2 5/16"
Minimum size 7 1/2" x 7 1/2"
NOT AVAILABLE IN COLORTONE FINISHES
Mitered DoorRope Insert in door frame
Minimum Size 8 5/8" x 8 5/8"
NN N
9" base & wall cabinets will have doors with cut down stiles inInset and 3/8" Inset. Standard Overlay will use full size stiles, but the overlay will be larger and a concealed hinge will be used.
N
N N N N
9" base & wall cabinets are not available in 3/8" Inset.Standard Overlay and Full Overlay will use full size stiles, but the overlay will be 1 3/8" and a concealed hinge will be used.
Standard Drawer Fronts
Matching 5-piece Drawer FrontsALEXANDRIA AMESBURY FRANKLIN MONROE
PROVIDENCEANNAPOLISWASHINGTONKINGSTONAUSTIN
ALEXANDRIARICHMONDSPRINGFIELDAUGUSTAMONROEFRANKLINSAVANNAHCHARLESTONEMMITSBURG
COLUMBUSOLD FORGE
ALL EXCEPTASTORIA
#10 KEYSTONE # 10141 SLAB
SAVANNAH CHARLESTON ALEXANDRIA MITER BRUSSELS
PRESTWICK EMMITSBURG SHELDON MADISON
PROVENCAL FLAT OLD FORGE PRESTIGE
COPENHAGEN MILAN & MILAN FLAT MIRAGE OXFORD
CORNWALL CHURCHILL LASALLE
HASTINGSBRIGHTON
ROPE
PROVENCAL &