windsor pump co. · 2111 pump shaft albero della pompa ... 4130 gland packing guarnizione a treccia...
TRANSCRIPT
MUCentrifugal pumps according to EN 733
Pompe centrifughe normalizzate EN 733
6 7
MUCENTRIFUGAL PUMPS ACCORDING TOEN 733 STANDARDSPOMPE CENTRIFUGHE NORMALIZZATE EN 733
COMMON AND GeNeRAL USeFresh and sea water, condensate, oils, chemical and petro-chemical products.
IMPIeGHIPer acqua, acqua mare, condensato, prodotti chimici, petrolchimici.
MAIN APPLICAtIONS Shipbuilding industry, heating plants, air conditioning sy-stem, aqueducts, effluent treatment plants, fire fighting, petrochemical plants.
PRINCIPALI APPLICAZIONI Applicazioni per uso cantieristico, impianti di riscaldamento, impian-ti di condizionamento, acquedotti, trattamento acque, antincendio, convogliamento idrocarburi.
MAIN FeAtUReS
CARAtteRIStICHe COStRUttIVe
PUMP: centrifugal type, end-suction single volute casing, single flow and axial inlet.POMPA: centrifuga con corpo a spirale orizzontale monostadio ad unico flusso ed aspirazione assiale.
IMPELLER: high efficiency, close type, statically and dynami-cally balanced. Low axial thrust thanks to impeller provided with balancing holes.GIRANTE: di tipo chiuso ad elevato rendimento, equilibrata statica-mente e dinamicamente. Equilibratura della spinta assiale mediante camera anulare sita posteriormente alla girante stessa munita di fori di bilanciamento.
MOUNTING SYSTEM: shaft supported by radial and thrust type bearings placed in an oil bath bracket or, upon request, by self lubricated or grease lubricated ball bearings. The bra-cket is usually made of cast-iron, bronze or stainless steel for special executions (non magnetic pumps).SUPPORTAZIONE: albero supportato da cuscinetti radiali ed assiali posizionati in un supporto a bagno d’olio o a richiesta con cuscinetti au-tolubrificanti o lubrificati a grasso. Supporto costruito normalmente in ghisa, il quale può essere prodotto in bronzo o in acciaio inox per utilizzi speciali (pompe amagnetiche). .
SEAL: single mechanical seal to DIN 24960. Special mechanical seal or car-tridge type for specific application or aggressive liquids. Possibility to install soft-packing with external flushing. For temperature higher than 120°C, it is possible to fit the pump with a cooling chamber.TENUTA: tenuta meccanica singola normalizzata DIN 24960. Te-nute speciali e a cartuccia per liquidi ed applicazioni particolari. Possi-
bilità di installare tenuta a baderna con flussaggio esterno. Per tempe-rature superiori ai 120 °C possibilità di dotare la pompa di camera di raffreddamento della tenuta.
SELF-PRIMING: Small and medium size pumps can be equip-ped with built-in priming element; all sizes can be supplied in self-priming version with an additional air ejector.AUTOADESCANTE: taglie piccole e medie possono essere fornite di elemento autoadescante ad anello liquido; tutte le taglie possono es-sere fornite con eiettore ad aria automatico.
BACK PULL OUtIt is possible to remove the rotating components without disturbing pipes, pump casing and motor by using a flexi-ble spacer coupling.
SMONtAGGIOImpiegando un giunto spaziatore è possibile sfilare la parte rotante senza intervenire sulle tubazioni, corpo-pompa e motore.
BASe PLAteThe base plate is generally built of welded steel and it can be provided with drain-pan for possible drippings.To comply with special requirements (non magnetic and/or anti vibration) it can be manufactured in stainless steel (AISI 316) and equipped with anti vibration and/or anti-shock resilient mountings.
BASAMeNtOIl basamento è costruito normalmente in acciaio elettro-saldato, lo stes-so può essere corredato di drenaggi per eventuali stillicidi della pompa. Per esecuzioni speciali (amagnetiche e/o antivibrazione) può essere co-struito in acciaio inox e corredato di resilienti antivibrazione e antishock.
SPeCIAL VeRSIONSSpecial versions according to Naval Rules are also available: shock-proof, vibration-proof, noise-proof, non magnetic.
COStRUZIONI SPeCIALISono previste costruzioni a norma MARINA MILITARE: antishock, an-tivibrazione, antirumore, amagnetiche
6 7
MU
MU
L/LD
SM
CA
VS
VL
CN
ZNG
/GH
BT
AD
MM
PIN
SWL
MPF
MAteRIALSMATERIALI
MAx. wORKING PReSSURePRESSIONE MAx. ESERCIZIO
CAST IRONGHISA 10 bar
STAINLESS STEEL, BRONZE, SPECIAL ALLOY ACCIAIO INOx, BRONZO, LEGHE SPECIALI 16 bar
NOTE: SPECIAL ExECUTIONS ExCEEdING THE AbOvE LIMITS AvAILAbLE ON REQUESTNOTA: ESECUZIONI SPECIALI AL DI FUORI DEI LIMITI SOPRAESPOSTI REALIZZATE SU RICHIESTA
INteRCHANGeABILIty INTERCAMbIAbILITà:
MODELS MODELLI 45
CASINGS CORPI 45
IMPELLERSGIRANTI 45
SHAFTSALBERI 6
BEARING BRACKETSSUPPORTI 6
COVERS COPERCHI 6
MECHANICAL SEALS TENUTE MECCANICHE 6
self priming element with liquid ringelemento autoadescante ad anello liquido
close coupled versionversione monoblocco
bare shaft versionversione ad asse nudo
8 9
LONGItUDINAL SeCtIONSEZIONE LONGITUDINALE
6576.1
42006855.1
6510.1
6510.2
6700.16581
1510
22006510.2
6579
4609
6700.2
3260
6510.3
3858
2540
4300
1225
6577
3260
3017
6576.23130
3134
38543011
2111
43006577
6855.3 45906855.2
1110 4590
1521
4120
6573
24504130
4610
65804134
SOFt PACKING VeRSIONVERSIONE TENUTA A BADERNA
4300
229125205110
6519
65456700.3 5100
Pos Description descrizione
1110 Pump casing Corpo pompa
1225 Casing cover Coperchio del corpo
1510 Wear ring Anello di usura
1521 Wear ring Anello di usura
2111 Pump shaft Albero della pompa
2200 Impeller Girante
2291 Priming stage impeller Girante stellare
2450 Shaft sleeve Camicia d’albero
2520 Shoulder ring Anello spallamento
2540 Deflector Deflettore
3011 Radial ball bearing Cuscinetto radiale
3017 Angular ball bearing Cuscinetto obliquo
3130 Bearing bracket Supporto doppio
3134 Support foot Piede del supporto
3260 Bearing cover Coperchio supporto
3854 Oil filler plug Tappo per l’olio
3858 Oil level Spia dell’olio
4120 Stuffing box gland Premitreccia
4130 Gland packing Guarnizione a treccia
4134 Lantern ring Anello lanterna
4200 Mechanical seal Tenuta meccanica
4300 Radial shaft seal Anello di tenuta
4590 Gasket Guarnizione
4609 O-Ring O-Ring
4610 O-Ring O-Ring
5100 Priming stage casing Corpo autoadescante
5110 Priming stage cover Coperchio autoadescante
6510.1 Plug Tappo
6510.2 Plug Tappo
6510.3 Plug Tappo
6519 Thread fitting Raccordo
6545 Seeger Seeger
6573 Stud Prigioniero
6576.1 Screw Vite
6576.2 Screw Vite
6577 Screw Vite
6579 Screw Vite
6580 Nut Dado
6581 Impeller nut Dado girante
6700.1 Key Chiavetta
6700.2 Key Chiavetta
6700.3 Key Chiavetta
6855.1 Washer Rosetta
6855.2 Washer Rosetta
6855.3 Washer RosettaSeLF-PRIMING VeRSION
VERSIONE AUTOADESCANTE
8 9
LONGItUDINAL SeCtIONSEZIONE LONGITUDINALE
6576.1
42006855.1
6510.1
6510.2
6700.16581
1510
22006510.2
6579
4609
6700.2
3260
6510.3
3858
2540
4300
1225
6577
3260
3017
6576.23130
3134
38543011
2111
43006577
6855.3 45906855.2
1110 4590
1521
4120
6573
24504130
4610
65804134
SOFt PACKING VeRSIONVERSIONE TENUTA A BADERNA
4300
229125205110
6519
65456700.3 5100
Pos Description descrizione
1110 Pump casing Corpo pompa
1225 Casing cover Coperchio del corpo
1510 Wear ring Anello di usura
1521 Wear ring Anello di usura
2111 Pump shaft Albero della pompa
2200 Impeller Girante
2291 Priming stage impeller Girante stellare
2450 Shaft sleeve Camicia d’albero
2520 Shoulder ring Anello spallamento
2540 Deflector Deflettore
3011 Radial ball bearing Cuscinetto radiale
3017 Angular ball bearing Cuscinetto obliquo
3130 Bearing bracket Supporto doppio
3134 Support foot Piede del supporto
3260 Bearing cover Coperchio supporto
3854 Oil filler plug Tappo per l’olio
3858 Oil level Spia dell’olio
4120 Stuffing box gland Premitreccia
4130 Gland packing Guarnizione a treccia
4134 Lantern ring Anello lanterna
4200 Mechanical seal Tenuta meccanica
4300 Radial shaft seal Anello di tenuta
4590 Gasket Guarnizione
4609 O-Ring O-Ring
4610 O-Ring O-Ring
5100 Priming stage casing Corpo autoadescante
5110 Priming stage cover Coperchio autoadescante
6510.1 Plug Tappo
6510.2 Plug Tappo
6510.3 Plug Tappo
6519 Thread fitting Raccordo
6545 Seeger Seeger
6573 Stud Prigioniero
6576.1 Screw Vite
6576.2 Screw Vite
6577 Screw Vite
6579 Screw Vite
6580 Nut Dado
6581 Impeller nut Dado girante
6700.1 Key Chiavetta
6700.2 Key Chiavetta
6700.3 Key Chiavetta
6855.1 Washer Rosetta
6855.2 Washer Rosetta
6855.3 Washer RosettaSeLF-PRIMING VeRSION
VERSIONE AUTOADESCANTE
8 9
MU
MU
L/LD
SM
CA
VS
VL
CN
ZNG
/GH
BT
AD
MM
PIN
SWL
MPF
PUMP DIMENSIONSdIMENSIONI POMPA
ShaftALbERO
PUM
P tY
PEPO
MPA
TIP
O
SUCt
ION
fLaN
GEbO
CCA
ASP
.
DELIV
ERY
fLaN
GEbO
CCA
MAN
dATA
fLaNGES DIMENSIONSdIMENSIONI FLANGE
(UNI 2223-2229 PN 10 UNI 2223-2229 PN 16*)
hOLE
S NU
MBE
RNU
MER
O F
ORI
DRaI
NaGE
dREN
AGGI
O
VaCU
UM G
aUGE
MAN
OvUO
TOM
ETRO
PRES
SURE
GaU
GEM
ANO
MET
RO
PUM
P W
EIGh
tPE
SO P
OM
PA
a f e h h1 h2 b c m1 m2 n1 n2 s l M W d t u DNs DNd D D’ bf bf’ K K’ g g’ y y’ D1 PM1 PM2 Kg
63 237 300 272 112 160 50 12 100 70 220 180 12 36 110 161 19 21,5 6 25-160 25 25 124 124 16 16 85 85 14 14 4 4 1/4’’G 1/4’’G 1/4’’G 22
80 360 440 340 160 180 50 15 100 70 240 190 14 50 110 260 24 27 8 25-200 40 25 150 115 18 16 110 85 18 14 4 4 1/4’’G 1/4’’G 1/4’’G 41
80 360 440 292 132 160 50 15 100 70 240 190 14 50 110 260 24 27 8 32-160 50 32 165 140 20 18 125 100 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 43
80 360 440 340 160 180 50 15 100 70 240 190 14 50 110 260 24 27 8 32-200 50 32 165 140 20 18 125 100 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 43
110 360 470 405 180 225 65 18 125 95 320 250 14 50 110 260 24 27 8 32-250 50 32 165 140 20 18 125 100 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 62
80 360 440 292 132 160 50 15 100 70 240 190 14 50 110 260 24 27 8 40-160 65 40 185 150 20 18 145 110 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 43
100 360 460 340 160 180 50 15 100 70 265 212 14 50 110 260 24 27 8 40-200 65 40 185 150 20 18 145 110 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 45
100 360 460 405 180 225 65 15 125 95 320 250 14 50 110 260 24 27 8 40-250 65 40 185 150 20 18 145 110 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 60
125 470 595 480 200 280 65 20 125 95 345 280 14 80 110 340 32 35 10 40-315 65 40 185 150 20 18 145 110 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 98
100 360 460 340 160 180 50 15 100 70 265 212 14 50 110 260 24 27 8 50-160 65 50 185 165 20 20 145 125 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 48
100 360 460 360 160 200 50 15 100 70 265 212 14 50 110 260 24 27 8 50-200 65 50 185 165 20 20 145 125 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 48
100 360 460 405 180 225 65 15 125 95 320 250 14 50 110 260 24 27 8 50-250 65 50 185 165 20 20 145 125 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 60
125 470 595 505 225 280 65 25 125 95 345 280 14 80 110 340 32 35 10 50-315 65 50 185 165 22 20 145 125 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 100
100 360 460 360 160 200 65 15 125 95 280 212 14 50 110 260 24 27 8 65-160 80 65 200 185 22 20 160 145 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 49
100 360 460 405 180 225 65 15 125 95 320 250 14 50 110 260 24 27 8 65-200 80 65 200 185 22 20 160 145 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 55
100 470 570 450 200 250 80 18 160 120 360 280 18 80 110 340 32 35 10 65-250 80 65 200 185 22 20 160 145 18 18 4 4 3/8’’G 1/4’’G 3/8’’G 80
125 470 595 505 225 280 80 25 160 120 400 315 18 80 110 340 32 35 10 65-315 80 65 200 185 22 20 160 145 18 18 4 4 3/8’’G 1/4’’G 3/8’’G 101
125 470 595 605 250 355 80 25 160 120 420 335 18 80 110 340 32 35 10 65-400 80 65 200 185 22 20 160 145 18 18 4 4 3/8’’G 1/4’’G 3/8’’G 130
125 360 485 405 180 225 65 15 125 95 320 250 14 50 110 260 24 27 8 80-160 100 80 220 200 22 22 180 160 18 18 8 4 1/4’’G 1/4’’G 1/4’’G 60
125 470 595 430 180 250 65 18 125 95 345 280 14 80 110 340 32 35 10 80-200 100 80 220 200 22 22 180 160 18 18 8 4 3/8’’G 1/4’’G 3/8’’G 75
125 470 595 480 200 280 80 18 160 120 400 315 18 80 110 340 32 35 10 80-250 100 80 220 200 22 22 180 160 18 18 8 4 3/8’’G 1/4’’G 3/8’’G 88
125 470 595 565 250 315 80 25 160 120 400 315 18 80 110 340 32 35 10 80-315 100 80 220 200 22 22 180 160 18 18 8 4 3/8’’G 1/4’’G 3/8’’G 111
125 530 655 635 280 355 80 25 160 120 435 355 18 110 110 370 42 45 12 80-400 100 80 220 200 22 22 180 160 18 18 8 4 3/8’’G 1/4’’G 3/8’’G 155
125 470 595 480 200 280 80 18 160 120 360 280 18 80 110 340 32 35 10 100-200 125 100 250 220 24 22 210 180 18 18 8 8 3/8’’G 1/4’’G 3/8’’G 85
140 470 610 505 225 280 80 18 160 120 400 315 18 80 110 340 32 35 10 100-250 125 100 250 220 24 22 210 180 18 18 8 8 3/8’’G 1/4’’G 3/8’’G 105
140 470 610 565 250 315 80 18 160 120 400 315 18 80 110 340 32 35 10 100-315 125 100 250 220 24 22 210 180 18 18 8 8 3/8’’G 1/4’’G 3/8’’G 116
140 530 670 635 280 355 100 25 200 150 500 400 22 110 110 370 42 45 12 100-400 125 100 250 220 24 22 210 180 18 18 8 8 3/8’’G 1/4’’G 3/8’’G 190
140 470 610 605 250 355 80 18 160 120 400 315 18 80 110 340 32 35 10 125-250 150 125 285 250 24 24 240 210 22 18 8 8 3/8’’G 1/4’’G 3/8’’G 120
140 530 670 635 280 355 100 25 200 150 500 400 22 110 110 370 42 45 12 125-315 150 125 285 250 24 24 240 210 22 18 8 8 3/8’’G 1/4’’G 3/8’’G 180
140 530 670 715 315 400 100 25 200 150 500 400 22 110 110 370 42 45 12 125-400 150 125 285 250 24 24 240 210 22 18 8 8 3/8’’G 1/4’’G 3/8’’G 205
180 635 815 900 400 500 140 28 280 200 680 540 28 140 110 430 60 64 18 125-500 150* 125* 285 250 26 26 240 210 22 18 8 8 3/4’’G 3/8’’G 3/8’’G 400
160 530 690 655 280 375 100 27 210 150 510 400 22 110 110 370 42 45 12 150-250 200 150 340 285 26 24 295 240 22 22 8 8 3/8’’G 1/4’’G 3/8’’G 200
160 530 690 680 280 400 100 25 200 150 550 450 22 110 110 370 42 45 12 150-315 200 150 340 285 26 24 295 240 22 22 8 8 3/8’’G 1/4’’G 3/8’’G 190
160 530 690 765 315 450 100 25 200 150 550 450 22 110 110 370 42 45 12 150-400 200 150 340 285 26 24 295 240 22 22 8 8 3/8’’G 1/4’’G 3/8’’G 235
180 640 820 950 400 550 140 28 280 200 680 540 28 140 160 435 60 64 18 150-500 200* 150* 340 285 30 26 295 240 22 22 12 8 3/4’’G 1/4’’G 3/8’’G 500
180 530 710 780 355 425 100 30 210 150 560 450 22 110 110 370 42 45 12 200-250 200 200 340 340 26 26 295 295 22 22 8 8 3/8’’G 1/4’’G 3/8’’G 250
200 605 805 805 355 450 110 30 210 150 560 450 25 110 160 432 60 64 18 200-315 250 200 395 340 28 26 350 295 22 22 12 8 3/8’’G 1/4’’G 3/8’’G 330
200 605 805 855 355 500 140 28 280 200 680 540 28 110 160 432 60 64 18 200-400 250 200 395 340 32 26 350 295 22 22 12 8 1’’G 1/4’’G 3/8’’G 410
200 640 840 1055 455 600 150 30 320 250 800 650 28 140 160 435 60 64 18 200-500 250* 200* 405 340 32 29 355 295 25 22 12 12 3/4’’G 3/8’’G 3/8’’G 600
250 605 855 960 400 560 130 30 280 200 700 560 25 110 160 432 60 64 18 250-250 300 250 445 395 28 28 400 350 22 22 12 12 3/8’’G 1/4’’G 3/8’’G 450
250 605 855 960 400 560 130 30 280 200 700 560 25 110 160 430 60 64 18 250-315 300 250 445 395 28 28 400 350 22 22 12 12 3/8’’G 1/4’’G 3/8’’G 460
225 605 830 1000 375 625 110 30 300 220 800 680 25 110 160 432 60 64 18 250-400 300 250 445 395 28 28 400 350 22 22 12 12 3/8’’G 3/8’’G 3/8’’G 485
250 750 10001100 430 670 135 30 300 220 800 665 28 140 160 526 65 69 18 250-450 300 250 445 395 28 28 400 350 22 22 12 12 3/8’’G 3/8’’G 3/8’’G 550
280 640 920 1145 475 670 140 30 260 190 810 670 28 140 160 435 60 64 18 250-500 300* 250* 460 405 32 32 410 355 25 25 12 12 3/4’’G 3/8’’G 3/8’’G 650
300 754 10541280 530 750 160 35 320 250 960 790 28 140 160 530 65 69 18 300-400-2 350 300 533 483 36 32 460 400 22 22 16 12 3/4’’G 3/8’’G 3/4’’G 750
280 754 10341020 420 600 140 35 280 200 720 580 28 140 160 530 65 69 18 300-400-B2 350 300 533 483 36 32 460 400 22 22 16 12 3/4’’G 3/8’’G 3/4’’G 520
s
PM1
N.y/Øg
N.y'/Øg'PM2
c
m2m1
W
bf
a
bf'
f
e
h1
n2n1
M b
l
h2h
K'DNd
D'
DN
s
h1
D SHAFTK
X
D1
d
t
u
FOR MU 250-450 X= 20PER MU 250-450
FOR MU 250-400 X= 25PER MU 250-400
SHAFT ENDESTREMITà D’ALBERO
key ACCorDInG To unI 6604chIAVETTA SEcoNDo UNI 6604
s
PM1
N.y/Øg
N.y'/Øg'PM2
c
m2m1
W
bf
a
bf'
f
e
h1
n2n1
M b
l
h2h
K'DNd
D'
DN
s
h1
D SHAFTK
X
D1
d
t
u
s
PM1
N.y/Øg
N.y'/Øg'PM2
c
m2m1
W
bf
a
bf'
f
e
h1
n2n1
M b
l
h2h
K'DNd
D'
DN
s
h1
D SHAFTK
X
D1
d
t
u
s
PM1
N.y/Øg
N.y'/Øg'PM2
c
m2m1
W
bf
a
bf'
f
e
h1
n2n1
M b
l
h2h
K'DNd
D'
DN
s
h1
D SHAFTK
X
D1
d
t
u
10 11
PERFORMANCES PRESTAZIONI
HEA
D
PREV
ALE
NZA
1450 RPM
CAPACITY PORTATA Q m3/h
25-160
32-160
40-160
50-160 65-160
32-200 40-200
32-25040-250
65-400
40-315
25-20050-200 65-200
80-160
80-200 100-200
65-315
125-250
100-250
65-250
80-250
80-400 100-400125-400
150-400
250-315
200-315150-315125-315100-315
80-315
150-250
200-250
200-500
50-250 250-250
150-500125-500
250-400
200-400
250-500
50-315
300-400250-450
2 3 4 5 10 20 30 40 50 100 200 300 400 500 1000 1600
2
3
4
5
10
20
30
40
50
100
100
10 3020 40 50 100 200 300 400 500 1000 2000 80003000 5000
10
20
30
40
50
200
300
400
500160
H feet
USGPM
H mt
PERFORMANCES PRESTAZIONI
HEA
D
PREV
ALE
NZA
CAPACITY PORTATA Q m3/h
2900 RPM
2 3 4 5 10 20 30 40 50 100 200 300
10 20 30 40 50 100 200 300 400 500 1000 2000 3000
15
20
25
30
40
50
60
70
80
90100
120
140
160
50
60
70
80
90
100
200
300
400
500
500 1000
25-160
25-200
32-160
32-200
32-250
40-1
60
40-200
40-250
40-315
50-160
50-200
50-250
65-160
65-200
65-250
65-315
80-160
80-200
80-250
50-315
100-200
100-250
100-315125-315
125-250
80-315
H mt
USGPM
H feet
PERFORMANCES PRESTAZIONI
HEA
D
PREV
ALE
NZA
1450 RPM
CAPACITY PORTATA Q m3/h
25-160
32-160
40-160
50-160 65-160
32-200 40-200
32-25040-250
65-400
40-315
25-20050-200 65-200
80-160
80-200 100-200
65-315
125-250
100-250
65-250
80-250
80-400 100-400125-400
150-400
250-315
200-315150-315125-315100-315
80-315
150-250
200-250
200-500
50-250 250-250
150-500125-500
250-400
200-400
250-500
50-315
300-400250-450
2 3 4 5 10 20 30 40 50 100 200 300 400 500 1000 1600
2
3
4
5
10
20
30
40
50
100
100
10 3020 40 50 100 200 300 400 500 1000 2000 80003000 5000
10
20
30
40
50
200
300
400
500160
H feet
USGPM
H mt
PERFORMANCES PRESTAZIONI
HEA
D
PREV
ALE
NZA
CAPACITY PORTATA Q m3/h
2900 RPM
2 3 4 5 10 20 30 40 50 100 200 300
10 20 30 40 50 100 200 300 400 500 1000 2000 3000
15
20
25
30
40
50
60
70
80
90100
120
140
160
50
60
70
80
90
100
200
300
400
500
500 1000
25-160
25-200
32-160
32-200
32-250
40-1
60
40-200
40-250
40-315
50-160
50-200
50-250
65-160
65-200
65-250
65-315
80-160
80-200
80-250
50-315
100-200
100-250
100-315125-315
125-250
80-315
H mt
USGPM
H feet
10 11
MU
MU
L/LD
SM
CA
VS
VL
CN
ZNG
/GH
BT
AD
MM
PIN
SWL
MPF
25-160
40-160
25-200
32-160
32-200
32-250
50-160 65-160
80-160
40-200
40-250
40-315
50-200
50-250
80-315100-315
125-315
150-315200-315
200-500250-500150-500
150-400125-400
100-400
80-400
250-315
200-250150-250
125-250100-25080-250
65-250
80-200 100-200
65-200
65-400
250-400
300-400
250-250
125-500
200-400
50-315 65-315
250-450
PERFORMANCES PRESTAZIONI
H feet
HEA
D
PREV
ALE
NZA
H mt
2 3 4 5 10 20 30 40 50 100 200 300 400 500 1000 1600
2
3
4
5
10
20
30
40
50
100
100
10 3020 40 50 100 200 300 400 500 1000 2000 80003000 5000
10
20
30
40
50
200
300
400
500160
CAPACITY PORTATA Q m3/h
1750 RPM
USGPM
PERFORMANCES PRESTAZIONI
HEA
D
PREV
ALE
NZA
CAPACITY PORTATA Q m3/h
3500 RPM
25-160
25-200
32-160
32-200
32-250
40-160
50-160
40-200
40-250
50-200
50-250
65-160
65-200
65-250
80-160
80-200
125-250
100-250
100-200
80-250
80-315
2 3 4 5 10 20 30 40 50 100 200 300 700
10 20 30 40 50 100 200 300 400 500 1000 2000 300050
15
20
25
30
40
50
60
70
80
90
100
120
140
160
50
60
70
80
90
100
200
300
400
500
USGPM
H mtH feet
Atex on request
Head Office 3057 Marentette Ave Windsor, On N8X 4G1
Phone: 1-(519) 969-2190 Fax: 1-(519) 969-2047
Dan KurtzPhone: 1-(226) 377-4100
Fax: 1-(905) 847-2425
Email: [email protected] www.windsorpump.com
Peter KurtzPhone: 1-(905) 302-3933
Fax: 1-(905) 847-2425
E-mail: [email protected] www.windsorpump.comEmail: [email protected]
Sales and Engineering
MCARecessed impeller torque flow pumps
Pompe con girante arretrata ad effetto vortice
22 23
MCANO CLOGGING RECESSED IMPELLERTORQUE FLOW PUMPS POMPE CON GIRANTE APERTA ARRETRATAAD EFFETTO VORTICE
DESCRIPTIONThanks to the shape of the impeller and to its recessed po-sition in the casing, MCA pumps are suitable for pumping viscous and pasty liquids containing suspended solids.
DESCRIZIONELe pompe centrifughe serie MCA, grazie alla girante aperta ed alla sua posizione arretrata rispetto al corpo a voluta, sono particolarmente adatte al convogliamento di fluidi con corpi solidi in sospensione senza alcun pericolo di intasamento.
MAIN FEATURES
CARATTERISTICHE COSTRUTTIVE
IMPELLER: the impeller is of the open type with radial blades.The impeller is provided with back vanes to balance the axial thrust and the pressure in the stuffing box area.GIRANTE: le giranti sono aperte a palette radiali.Nella parte posteriore è prevista una palettatura per equilibrare la spinta assiale e la pressione esistente nella zona di tenuta.
CASING: volute type with ample section end suction and top discharge nozzles.The flanges are NP 10 according to UNI - EN - DIN - JIS - standards.CORPO: Il corpo è a spirale con un’ampia sezione di passaggio.La bocca aspirante è assiale, la bocca di mandata è radiale, rivolta verso l’alto. Le flange d’attacco hanno foratura PN 10 in accordo a UNI - EN - DIN - JIS - standards.
SHAFT SEALING: basic pump version is mechanically sealed but soft packing with optional external flushing with clean fluid can be fitted. In case of dangerous liquids, pumps can be provided with double mechanical seals completed with barrier system.TENUTA SULL’ ALBERO: la tenuta prevista di serie è meccanica, ma può essere installata anche la baderna flussata da liquido pulito dall’ester-no. In caso di liquidi pericolosi la pompa può essere predisposta con tenuta meccanica doppia e sistema di sbarramento.
MATERIALSStandard constructions are in cast iron, carbon steel, stainless steels. Any other material combinations can be supplied.
MATERIALISono previste costruzioni standard in ghisa, acciaio al carbonio, acciai inox. Su richiesta sono realizzabili altre metallurgie.
APPLICATIONSSewage treatment plants, paper industry, food and sugar industry and generally to convey all liquids with suspended solids.
IMPIEGHIImpianti di depurazione, industria cartaria e della cellulosa, industria alimentare e saccarifera, chimica e petrolchimica, tessile, impianti di depurazione ed in generale per convogliare tutti quei liquidi contenenti solidi sospesi.
PERFORMANCESCapacity up to 500 m3/h.Total dynamic head up to 100 meters.Speed from 750 to 3500 rpm
PRESTAZIONIPortate fino a 500 m3/h.Prevalenza fino a 100 metri.Velocità da 750 a 3500 giri al minuto
22 23
MU
MU
L/LD
SM
CA
VS
VL
CN
ZNG
/GH
BT
AD
MM
PIN
SWL
MPF
MATERIALSMATERIAlI
MAx. wORkING PRESSUREPREssIONE MAx. EsERCIzIO
CAST IRoNGhISA 10 bar
STAINLESS STEEL, bRoNzE, SPECIAL ALLoyS ACCIAIO INOx, BRONzO, LEGhE SPECIALI 16 bar
NOTE: sPECIAl ExECuTIONs ExCEEDING ThE AbOVE lIMITs AVAIlAblE ON REquEsTNOTA: ESECUzIONI SPECIALI AL DI fUORI DEI LIMITI SOPRAESPOSTI REALIzzATE SU RIChIESTA
open impellergirante aperta
INTERCHANGEAbILITy INTERCAMbIAbIlITà
MoDELS MODELLI 19
CASINGS CORPI 19
IMPELLERSGIRANTI 19
SHAFTSALBERI 3
bEARING bRACkETSSUPPORTI 3
MECHANICAL SEALS TENUTE MECCANIChE 3
close coupled versionversione monoblocco
bare shaft versionversione ad asse nudo
24 25
LONGITUDINAL SECTIONSEzIONE LONGITUDINALE
MAIN VERSIONSPRINCIPALI VERSIONI
wORkING PRINCIPLEPRINCIPIO DI FUNZIONAMENTO
6510.265816510.1 6700.1
11106510.1
122131362252 6577.2
31604200
4610 21106576.1
2914
6510.1
6510.1
1110
6577.3
6576.24610
6577.26700.16510.2
22523136
6576.1
42001221
6577.1
4300
301738543260
6510.2
6577.1
2540 31304300
3017
31343858
2110
6576.3
3260
6700.2
CLOSE COUPLED VERSIONVERSIONE MONOBLOCCO
Pos Description Descrizione
1110 Pump casing Corpo pompa
1221 Casing cover Coperchio del corpo
2110 Pump shaft Albero della pompa
2252 Radial impeller open Girante radiale aperta
2540 Deflector Deflettore
2914 Impeller hub cap Ogiva della girante
3017 ball bearing Cuscinetto a sfere
3130 Shaft sleeve Camicia d’albero
3130 bearing bracket Supporto doppio
3134 Support foot Piede del supporto
3136 Adjustable foot Piede orientabile
3160 Motor stool Lanterna motore
3260 bearing cover Coperchio supporto
3854 oil filler plug Tappo per l’olio
3858 oil level Spia dell’olio
Pos Description Descrizione
4200 Mechanical seal Tenuta meccanica
4300 Radial shaft seal Anello di tenuta
4610 o-Ring O-Ring
6510.1 Plug Tappo
6510.2 Plug Tappo
6576.1 Screw Vite
6576.2 Screw Vite
6576.3 Screw Vite
6577.1 Screw Vite
6577.2 Screw Vite
6577.3 Screw Vite
6581 Impeller nut Dado girante
6700.1 key Chiavetta
6700.2 key Chiavetta
24 25
MU
MU
L/LD
SM
CA
VS
VL
CN
ZNG
/GH
BT
AD
MM
PIN
SWL
MPF
MCA-VM MCA-M MCA vertical close coupled version close coupled version bare shaft version versione verticale monoblocco versione monoblocco versione ad asse nudo
MAIN VERSIONSPRINCIPALI VERSIONI
wORkING PRINCIPLEPRINCIPIO DI FUNZIONAMENTO
The special impeller shape and its position in the rear part of the casing operates in such a way that the solid particles in suspension flow through the casing wi-thout touching the impeller directly.La particolare forma della girante e la sua posizione arretrata rispetto alla voluta fan-no sì che le particelle solide in sospensione attraversino il corpo senza toccare la girante.
26 27
X
a f
l
y
c
b
g
h1
h2
h
n2n1
m1 m3
n3
m2
s
DN
s
k D
n° z HOLES ø g
DN
d
k' D'
n° z HOLES ø g'FORI FORI
GARBARINO
D1'
PM1
PM2
t
d1 u
PUMP DIMENSIONSDIMENsIONI POMPA
PUMP TYPEPOMPA TIPO
FLANGES DIMENSIONSDIMENsIONI FlANGE
(uNI 2223-2229 PN 10 uNI 2223-2229 PN 16*) DR
AINA
GEDR
ENAG
GIO
VACU
UM G
AUGE
MAN
OVu
OTO
MET
RO
PRES
SURE
GAU
GEM
ANO
MET
RO
PUM
P W
EIGH
TPE
sO P
OM
PA
a b c f g h1 h2 h m1 m2 m3 n1 n2 n3 l d1 t u s x y DNs DNd D D’ K K’ z/g z/g’ D1 PM1 PM2 Kg
78 60 553 475 15 160 180 340 100 70 50 300 240 150 50 24 27 8 16 82 140 32-200 50 32 165 140 125 100 4/18 4/18 1/4’’ 1/4’’ 1/4’’ 51
90 50 555 465 15 150 190 340 100 70 50 240 190 150 50 24 27 8 14 105 140 50-125 65 50 185 165 145 125 4/18 4/18 1/4’’ 1/4’’ 1/4’’ 47
100 50 630 530 15 150 190 340 100 70 50 240 190 150 50 24 27 8 14 135 140 50-140 65 50 185 165 145 125 4/18 4/18 1/4’’ 1/4’’ 1/4’’ 65
100 50 630 530 15 150 210 360 100 70 50 240 190 150 50 24 27 8 14 135 140 50-160 65 50 185 165 145 125 4/18 4/18 1/4’’ 1/4’’ 1/4’’ 70
100 60 750 650 15 180 225 405 100 70 50 300 240 150 80 32 35 10 14 140 140 50-200 65 50 185 165 145 125 4/18 4/18 1/4’’ 1/4’’ 1/4’’ 105
100 60 750 650 15 180 250 430 100 70 50 300 240 150 80 32 35 10 14 140 140 50-250 65 50 185 165 145 125 4/18 4/18 3/8’’ 1/4’’ 1/4’’ 120
105 90 765 660 18 220 310 530 120 90 50 370 290 150 80 32 35 10 18 156 140 50-280 65 50 185 165 145 125 4/18 4/18 3/8’’ 1/4’’ 1/4’’ 135
115 60 660 545 15 180 240 420 100 70 50 300 240 150 50 24 27 8 14 165 140 80-160 100 80 220 200 180 160 8/18 4/18 1/4’’ 1/4’’ 1/4’’ 80
125 60 800 675 15 180 250 430 100 70 50 300 240 150 80 32 35 10 14 190 140 80-200 100 80 220 200 180 160 8/18 4/18 1/4’’ 1/4’’ 1/4’’ 115
125 70 800 675 20 225 300 525 120 80 50 340 270 150 80 32 35 10 18 185 140 80-250 100 80 220 200 180 160 8/18 4/18 3/8’’ 1/4’’ 1/4’’ 130
125 90 800 675 18 220 335 585 120 90 50 370 290 150 80 32 35 10 18 191 140 80-280 100 80 220 200 180 160 8/18 4/18 3/8’’ 1/4’’ 1/4’’ 150
125 80 955 830 20 280 355 635 160 120 50 435 355 150 110 48 51,5 14 18 175 140 80-335 100 80 220 200 180 160 8/18 4/18 3/8’’ 1/4’’ 3/8’’ 245
140 70 825 685 20 225 280 505 120 80 50 340 270 150 80 32 35 10 18 210 140 100-200 125 100 250 220 210 180 8/18 8/18 3/8’’ 1/4’’ 1/4’’ 130
140 70 825 685 20 225 300 525 120 80 50 340 270 150 80 32 35 10 18 210 140 100-250 125 100 250 220 210 180 8/18 8/18 3/8’’ 1/4’’ 1/4’’ 165
140 80 980 840 20 250 355 605 160 120 50 400 315 150 110 48 51,5 14 18 200 140 100-280 125 100 250 220 210 180 8/18 8/18 3/8’’ 1/4’’ 1/4’’ 210
140 80 980 840 20 280 415 695 160 120 50 435 355 150 110 48 51,5 14 18 200 140 100-335 125 100 250 220 210 180 8/18 8/18 3/8’’ 1/4’’ 1/4’’ 260
165 80 875 710 20 280 370 650 160 120 50 400 315 150 80 32 35 10 18 240 100 150-250 200 150 340 285 295 240 8/22 8/22 3/8’’ 1/4’’ 1/4’’ 180
165 80 1030 865 20 280 395 675 160 120 50 435 355 150 110 48 51,5 14 18 250 140 150-280 200 150 340 285 295 240 8/22 8/22 3/8’’ 1/4’’ 1/4’’ 240
165 120 1030 865 24 320 435 755 130 80 50 520 400 150 110 48 51,5 14 18 260 140 150-335 200 150 340 285 295 240 8/22 8/22 3/8’’ 1/4’’ 1/4’’ 315
GR.24 GR.32 GR.48
26 27
MU
MU
L/LD
SM
CA
VS
VL
CN
ZNG
/GH
BT
AD
MM
PIN
SWL
MPF
PERFORMANCES PRESTAZIONI
HEA
D
PREV
ALE
NZA
1450 RPM
CAPACITY PORTATA Q m3/h
32-200
50-125
50-140
50-160
50-200
50-250
50-280
80-160
80-200
80-250
80-280
80-335
100-200
100-280
100-
250
150-250
150-
280
150-
335
100-335
2
2
3
4
5
10
20
30
40
50
100
10
20
30
40
50
200
H mt
2 3 4 5 10 20 30 40 50 100 200 300
10 20 30 40 50 100 200 300 400 500 1000 2000 300050
14
6070
500 1000
H feet
USGPM
PERFORMANCES PRESTAZIONI
HEA
D
PREV
ALE
NZA
CAPACITY PORTATA Q m3/h
2900 RPM
USGPM
50-250
50-200
50-160
50-140
50-125
32-200
50-280
80-250
80-160
80-200 H feet
6 7 8 9 10 50 10015 20 30 40 150 200 300 400
10007505002501007550
600500
2500
1098
100
50
40
30
20
15
200
300
200
300
400
500
100
30
40
50
1000
H mt
operating diagrams at 60 Hz for MCA pumps also available. Contact our main office. I campi di lavoro delle pompe MCA sono disponibili anche a 60 hz. Contattare il nostro ufficio.
Atex on request
www.lizea.com
Head Office 3057 Marentette Ave Windsor, On N8X 4G1
Phone: 1-(519) 969-2190 Fax: 1-(519) 969-2047
Dan KurtzPhone: 1-(226) 377-4100
Fax: 1-(905) 847-2425
Email: [email protected] www.windsorpump.com
Peter KurtzPhone: 1-(905) 302-3933
Fax: 1-(905) 847-2425
E-mail: [email protected] www.windsorpump.comEmail: [email protected]
Sales and Engineering
ZNDiathermic oil circulation pumps
Pompe circolazione olii diatermici
46 47
ZNDIATHERMIC OILCIRCULATION PUMPS DIN 4754pompe circolazioneolii diatermici din 4754
applicationzn pumps are designed to handle diathermic fluids up to 350°c temperature. pumped fluids should contain neither abrasive particles nor chemicals which may at-tack the pump materials. no cooling of the seal chamber required.
impieghile pompe zn sono progettate per circolazione di olii diatermici fino alla temperatura massima di 350 °c. i fluidi pompati non de-vono contenere sostanze abrasive o chimiche particolari che intac-chino i materiali della pompa. non necessitano di raffreddamento al dispositivo di tenuta.
constructionzn series pumps are of centrifugal, single stage, hori-zontal shaft type. self-balancing impeller by rear blades.the dimensions of the pump are according to iso 2858.the bearing housing has been specially designed to dis-sipate the heat originating from the pump casing and does not require a cooling circuit.the shaft is supported by two roller bearings, the pump side bearing is lubricated by oil and the coupling side bearing by grease. the mechanical seal is mounted in
the bearing housing between the bearings and its excel-lent performance is guaranteed by the shaft rigidity.the standard construction provides the outlet flanges according to Uni 2223/2229 np 16. Upon request Uni np 25 or ansi 150 rf can be supplied.
caratteristiche costruttivele pompe zn sono centrifughe monostadio ad asse orizzontale con girante chiusa a sbalzo.le dimensioni principali delle pompe sono secondo iso 2858.il supporto, particolarmente disegnato per smaltire il calore pro-veniente dal corpo pompa non ha bisogno di circuiti di raffredda-mento. l’albero è guidato da due cuscinetti a rotolamento di cui quello lato pompa lubrificato ad olio, quello lato accoppiamento lubrificato a grasso.la tenuta meccanica è montata sul supporto tra i cuscinetti e quin-di particolarmente garantita nel suo buon funzionamento dalla rigidità dell’albero.la costruzione standard prevede le flange delle bocche secondo uni 2223/2229 pn 16. su richiesta si eseguono forature uni pn 25 o ansi 150 rf.
materialsWet parts are made in nodular cast iron, impeller and bearing housing in cast iron, the shaft is in alloyed steel.
materialinormalmente le pompe zn vengono costruite con le parti in con-tatto con il liquido in ghisa sferoidale, le giranti e il supporto in ghisa, l’albero in acciaio legato.
interchangeability of componentshigh standardization of components permits to ratio-
bare shaft versionversione ad asse nudo
46 47
MU
MU
L/LD
SM
CA
VS
VL
CN
ZNG
/GH
BT
AD
MM
PIN
SWL
MPF
nalize common parts with a consequent reduc-tion of spare parts stock.
intercambiabilita’ delle partila loro elevata standardizzazione permette una grande razio-nalizzazione di particolari comuni con conseguente riduzione del magazzino ricambi.
characteristicscapacity: max. 350 m3/hhead: max. 100 mtemperature of liquid pumped: max. 350°cmaximum pressure inside pump casing : max. 16 barrotation speed: max. 3600 rpmflanges dn: 32 -125
prestaZioniportata: fino a 350 m3/hprevalenza: fino a 100 mtemperatura del liquido pompato: fino a 350°c pressione massima interna del corpo pompa: fino a 16 barVelocità di rotazione: fino a 3600 giri/1’ flange dn: da 32 a 125
workinggenerally the pump is driven by an electric motor coupled to the pump by means of an elastic cou-pling.it is possible to fit a flexible spacer coupling so as to dismantle the complete pump support without removing pump casing and motor from the base-plate. the coupling is protected by a cover, so as to prevent external intrusion
aZionamentogeneralmente l’azionamento è a mezzo motore elettrico ac-coppiato alla pompa attraverso un giunto elastico.impiegando un giunto con spaziatore è possibile smontare il supporto completo con coperchio posteriore senza rimuo-vere dal basamento il corpo pompa ed il motore elettrico.l’accoppiamento pompa-motore è protetto contro il pericolo di contatto esterno da un apposito coprigiunto.
coupling and baseplate versionversione con giunto e basamento
48 49
6510.2
4590.23261
6700.2 6542
6576.2
6577
3134
3133 4590.1
21103132
4590.2
6580
6573
6510.24130
4133
24604300 25223011 4200 11106545 1221 6510.16700.1
38546586 3849 6576.1 6576.13011 6546 15252200
2912
longitudinal sectionsezione longitudinale
materialsmateriali
max. working pressurepressione max. esercizio
nodUlar cast ironghisa sferoidale 16 bar
note: special executions exceeding the above limits available on requestnota: esecuzioni speciali al di fuori dei limiti sopraesposti realizzate su richiesta
interchangeability intercambiabilità
Models modelli 16
casings corpi 16
iMpellersgiranti 16
shaftsalberi 2
bearing bracketssupporti 2
covers coperchi 5
Mechanical seals tenute meccaniche 2
48 49
MU
MU
L/LD
SM
CA
VS
VL
CN
ZNG
/GH
BT
AD
MM
PIN
SWL
MPF
pos description descrizione
1110 pump casingcorpo pompa
1221 casing cover coperchio del corpo
1525 Wear ring anello di usura
2110 pump shaft albero della pompa
2200 impeller girante
2460 spacer sleeve bussola distanziatrice
2522 nilos seal ring anello di tenuta nilos
2912 impeller nut dado della girante
3011 radial ball bearing cuscinetto radiale a sfere
3132 bearing bracket lantern lanterna del supporto
3133 bearing bracket semisupporto lato comando
3134 support foot piede del supporto
3261 bearing cover coperchio del supporto
3849 straight ball greaser ingrassatore
3854 oil filler plug tappo
4130 gland packingguarnizione a treccia
4133 packing ring anello di fondo
4200 Mechanical sealternuta meccanica
4300 radial shaft seal anello di tenuta
4590.1 gasket guarnizione
4590.2 gasket guarnizione
6510.1 plugtappo
6510.2 plug tappo
6542 lockwasherrosetta di sicurezza
pos description descrizione
6545 seegerseeger
6546 seeger seeger
6573 stud prigioniero
6576.1 screw Vite
6576.2 screw Vite
6577 screw Vite
6580 nut dado
6586 locknut ghiera
6700.1 key chiavetta
6700.2 key chiavetta
- 350- 300- 250- 200- 150- 100- 50- 0
- 600
- 500
- 400
- 300
- 200
- 100
°C °F
heat dissipationdispersione del calore
50 51
PUMP SIzegrandezza
pompa
beARING HOUSING SIzegrandezza supporto
PUMP DIMeNSIONSdimensioni pompa
SHAfT eNDestremità d’albero
fOUNDATION bOLTS bulloni di fondazione
DNs DNd a b c f g1 g2 h1 h2 m1 m3 n1 n3 d1
j6ø l t u y i1 i2 m2 n2 n4 s1 s2 v w
50-32-160 24 50 32 80 50 465 385 14 8 132 160 100 50 240 150 24 50 27 8 100 35 35 70 190 110 14 14 100 285
50-32-200 24 50 32 80 50 465 385 14 8 160 180 100 50 240 150 24 50 27 8 100 35 35 70 190 110 14 14 100 285
50-32-250 32 50 32 100 65 600 500 16 8 180 225 125 50 320 150 32 80 35 10 100 47,5 32 95 250 110 14 14 130 370
65-50-160 24 65 50 80 50 465 385 14 8 132 160 100 50 240 150 24 50 27 8 100 35 35 70 190 110 14 14 100 285
65-40-200 24 65 40 100 50 485 385 14 8 160 180 100 50 265 150 24 50 27 8 100 35 35 70 212 110 14 14 100 285
65-40-250 32 65 40 100 65 600 500 16 8 180 225 125 50 320 150 32 80 35 10 100 47,5 32 95 250 110 14 14 130 370
80-65-160 24 80 65 100 50 485 385 14 8 160 180 100 50 265 150 24 50 27 8 100 35 35 70 212 110 14 14 100 285
80-50-200 24 80 50 100 50 485 385 14 8 160 200 100 50 265 150 24 50 27 8 100 35 35 70 212 110 14 14 100 285
80-50-250 32 80 50 125 65 625 500 16 8 180 225 125 50 320 150 32 80 35 10 100 47,5 32 95 250 110 14 14 130 370
100-80-160 32 100 80 100 65 600 500 16 8 160 200 125 50 280 150 32 80 35 10 100 47,5 32 95 212 110 14 14 130 370
100-65-200 32 100 65 100 65 600 500 16 8 180 225 125 50 320 150 32 80 35 10 140 47,5 32 95 250 110 14 14 130 370
100-65-250 32 100 65 125 80 625 500 18 8 200 250 160 50 360 150 32 80 35 10 140 60 32 120 280 110 18 14 130 370
125-80-160 32 125 80 125 65 625 500 16 8 180 225 125 50 320 150 32 80 35 10 140 47,5 32 95 250 110 14 14 130 370
125-80-200 32 125 80 125 65 625 500 16 8 180 250 125 50 345 150 32 80 35 10 140 47,5 32 95 280 110 14 14 130 370
125-80-250 32 125 80 125 80 625 500 18 8 225 280 160 50 400 150 32 80 35 10 140 60 32 120 315 110 18 14 160 370
125-100-200 32 125 100 125 80 625 500 16 8 200 280 160 50 360 150 32 80 35 10 140 60 32 120 280 110 18 14 160 370
DNs
DNd
i2
s2
m3
n4
n3
b
m1
n2 n1
m2
s1
i1wv
l
f a
c
h1
h2
y
g1
g2
t
d1 u
G 1/4"
G 1/4"
G 3/8"
flange: Uni - pn16ansi 150rf
flangia: uni - pn16ansi 150rf
y: MiniMUM diMension for disMantling WithoUt re-Moving the Motory: misura minima per losmontaggio senzatogliere il motore
shaft endestremità d’albero
key according to Uni 6604chiaVetta secondo uni 6604
DNs
DNd
i2
s2
m3
n4
n3
b
m1
n2 n1
m2
s1
i1wv
l
f a
c
h1
h2
y
g1
g2
t
d1 u
G 1/4"
G 1/4"
G 3/8"
50 51
MU
MU
L/LD
SM
CA
VS
VL
CN
ZNG
/GH
BT
AD
MM
PIN
SWL
MPF
PERFORMANCES PRESTAZIONI
HEA
D
PREV
ALE
NZA
1450 RPM
CAPACITY PORTATA Q m3/h
3 4 5 10 20 30 40 50 100 2003
4
5
10
20
30
20 30 40 50 100 200 300 400 500 800
10
15
20
30
40
50
125
100
40
H mtH feet
USGPM
125-80-250
100-65-250
80-50-25065-40-250
50-32-250
50-32-200
50-32-160 65-50-16080-65-160
100-80-160 125-80-160
65-40-200
80-50-200100-65-200
125-80-200
125-100-200
5 10 20 4030 50 100 200 300
20
10
30
40
50
100
30 40 50 100 200 300 400 500 1000
400
300
200
100
40
50
150
H mtH feet
50-32-250
65-40-25080-50-250
100-65-250125-80-250
100-65-200
80-50-200
65-40-20050-32-200
50-32-16065-50-160 80-65-160
100-80-160125-80-160
125-80-200125-100-200
Atex on request
www.lizea.com
Head Office 3057 Marentette Ave Windsor, On N8X 4G1
Phone: 1-(519) 969-2190 Fax: 1-(519) 969-2047
Dan KurtzPhone: 1-(226) 377-4100
Fax: 1-(905) 847-2425
Email: [email protected] www.windsorpump.com
Peter KurtzPhone: 1-(905) 302-3933
Fax: 1-(905) 847-2425
E-mail: [email protected] www.windsorpump.comEmail: [email protected]
Sales and Engineering