woodworking: joinery
DESCRIPTION
WOODWORKING: JOINERY. Joinery. What is joinery? In our case – we will be looking at the fastening or combining of two or more boards together when building our projects. It is important to have good, strong joints when building furniture. - PowerPoint PPT PresentationTRANSCRIPT
WOODWORKING: JOINERY
Joinery What is joinery?
• In our case – we will be looking at the fastening or combining of two or more boards together when building our projects.
It is important to have good, strong joints when building furniture.
It is sometimes good to use both advanced joinery methods and fasteners when assembling the project.
Butt Joints Used to join 2
boards• Edge to edge• End to side• End to edge
Very simple form of joinery
Dado Joints Slot or groove is cut
across the width of a board (on the inside) when joining 2 boards together
Boards are joined at right angles to one another
Remove a portion from one board to accept the other board (usually half the thickness of your material)
Rabbet Joints Similar to a dado
joint Remove material
from the end or edge of a board
Makes the boards connect at a right angle to one another
Spline Joints The spline is the strip of
wood used in the center of this joint.
The spline is inserted into matching grooves/troughs on two boards.
Splines are often used to reinforce miter or butt joints.
Spline can also help align the pieces for the glue-up procedure.
You can also use a spline joint as a decorative accent in your project.
Mitre Joints The division, into 2
equal parts, of an overall angle created by 2 intersecting parts• Most frames that use
miter joints meet at 90˚ so the two pieces are cut at 45˚
Precise cuts are very important – you will see gaps and have a less secure joint if your cuts are not accurate
Lap Joints (ie. end-lap, half-lap) Remove the full width
of the intersecting wood pieces.
The two parts meet and together make up the entire thickness.
Should be used with fasteners as well in order to increase the strength of the joint.
Tongue-And-Groove Joints A short tongue is
cut along one edge. A matching groove
is cut along the edge of the other board.
Good to use when making a wider panel from narrow boards.
Box Joints Cut straight slots and
grooves out of the end of two boards in order to form an interlocking system at the corners.
Sometimes referred to as a finger joint.
Used for decorative reasons as well as to strengthen the assembly.
Mortise-and-Tenon Joints Join two pieces of wood
at an angle (usually 90˚) A tenon (a portion that
sticks out) is cut on the end of one board.
A matching recess, slot or hole is cut into the other piece (mortise).
The two fit together to make a strong joint that is frequently used in furniture making.
Dovetail Joints A system of pins and
tails that interlock together.
Tails are the triangular shape cut through the thickness of a board.
Pins are more slender portions cut along the grain of the other board.
One of the strongest joints.
Also very attractive for of joinery.
Dowel Joints Cylindrical piece of
wood used to join two pieces of wood together.
Holes are drilled into both pieces of wood at precise locations.
The dowel (cylindrical piece) fits into the hole on either side.
Makes a butt joint more secure.
Biscuit Joint Thin football shaped
disk is used to join two boards together.
A slot is cut into each board.
The biscuit fits halfway into each side of the slot.
The biscuit expands with the glue to fill the gap.
FastenersWhat are the different types of fasteners?
Your task…. Define the term fastener as it would be used in the
woodshop. Choose 3-4 specific types of fasteners (ie. Glue,
nails, screws, tape, etc.) and describe its benefits.• For example – Robertson screw, Gorilla Glue, and roofing
nails• Why would we use waterproof glue over regular wood glue.• Why do some nails have “twists” along the shank?
Do not write a novel – but make sure you have enough information about each.
If you would prefer to do a PowerPoint over a Word document – then do so!