work station crane dimensional information - gorbel
TRANSCRIPT
WORK STATION CRANEDIMENSIONAL INFORMATION
www.gorbel.comPhone: (585) 924-6262
Toll Free Phone: (800) 821-0086© 2014 Gorbel Inc. All Rights Reserved
®
INSTALLATION GUIDELINESCAPACITY SERIES WEIGHT
PER FOOTMAX.
L1MAX.
L2MAX.
L5MAX.
L9
250#GLC
GLCSAL
GLCSL
2.53#4.92#4.05#8.43#
6’20’20’25’
8”48”30”48”
18”18”48”18”
18”48”48”48”
500#
GLCGLCS
ALGLCSL
GLCSLX
4.15#7.44#4.87#
10.71#11.01#
6’20’20’25’30’
8”48”30”48”48”
24”24”48”24”24”
20”48”48”48”48”
1000#
GLCGLCS
ALGLCSL
GLCSLX
6.22#12.25#8.36#
14.08#17.47#
6’20’20’25’30’
8”48”30”48”48”
24”24”48”24”24”
20”48”48”48”48”
2000#
GLCGLCS
ALGLCSL
GLCSLX
9.12#16.89#10.01#19.36#20.13#
6’20’20’25’30’
8”48”30”48”48”
24”24”48”24”24”
24”48”48”48”48”
4000#GLC
GLCSGLCSL
GLCSLX
9.12#20.68#26.21#28.22#
4’20’25’30’
8”48”48”48”
24”24”24”24”
24”48”48”48”
L1 = MAXIMUM HANGER CENTERLINE Maximum Hanger Centerline is considered from the center of a hanger to the center of the neighboring hanger.
L2 = SPLICE JOINT CENTERLINE TO HANGER CENTERLINE Splice Joint Centerline to Hanger Centerline is considered from the center of a splice joint to the center of the nearest hanger.
L4 = BRIDGE SPAN Bridge Span is considered from centerline to centerline of runways. L4 = Bridge Overall Length - (2 x Bridge Can lever)
L5 = BRIDGE CANTILEVER** Bridge Can lever is considered from the centerline of the runway to the end of the bridge.
L9 = MAXIMUM RUNWAY CANTILEVER Runway Can lever is considered from the center of the end hanger to the end of the runway.
Note: Same guidelines apply for Monorails (GLMS, GLMSL, GLMSLX, ALM), with the excep on of the “L5” dimension (not applicable).Note: Typical L5 in 12”. Max L5 may not be achievable (dependent on truss design of bridge).
Note: Depending on track series, an -kick-up end trucks may be required for the following: bridges with ≤ 8’ span (L4) and a bridge can lever (L5) ≥ 12” bridges with < 10’ span (L4) and a bridge can lever (L5) > 15” bridges with < 15’ span (L4) and a bridge can lever (L5) > 18”
*An -kick-up end trucks are not included as part of the standard crane kits.****2000# Ceiling Mounted systems and Monorails at 10’ span (L4) and bridge can lever (L5) 15” need an -kick-up end trucks.Consult Gorbel® factory for informa on on bridges greater than 15’ span (L4).
Bridge Series
Bridge Overall LengthSteel
≤ 23’ 28’ 29’ 33’ 34’250500
100020004000
12”12”12”12”15”
18”18”18”18”18”
24”24”24”24”24”
na18”18”18”18”
na24”24”24”24”
STAN
DARD
BRI
DGE
CAN
TILE
VER
Bridge Series
Bridge Overall LengthSteel
≤ 20’ 23’ 28’ 29’ 33’ 34’250500
100020004000
12”12”12”12”15”
18”18”18”18”18”
18”18”18”18”18”
na24”24”24”24”
na18”18”18”18”
na24”24”24”24”
1
L1
L1
L9
L2
L4
L5
L1
L1
L2
L4L5
L9
Note: For Bridge OALs between lengths shown, round up to the larger legnths. Maximum L5 may bot be achievable (dependant on truss design of bridge). The maximum L5 dimension using AL series rail does not pertain to coped aluminum bridges.
FREE STA
ND
ING
WO
RK
STATION
CR
AN
ESFREE STANDING WORK STATION BRIDGE CRANES
STEEL RUNWAYS WITH STEEL OR ALUMINUM BRIDGEISOMETRIC VIEW
2
Model Number:
Capacity: pounds
Bridge Length (L): (OAL)
Runway Length: (OAL)
Trolley Saddle Height: (TS)
L1: Are the number of support assemblies provided suffi cient?(See “SUPPORT” column on dimensional chart pages)
C: inches (hoist by others)
Gorbel® Free Standing Work Sta on Crane kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and aluminum systems), festoon stack-up sec on, splice joints and hanger brackets.
Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
L1
L1
L7
RUNWAY LENGTHBRIDGE LENGTH (L)
**CS(CLEAR SPAN)
*OAW(OVERALL WIDTH)
OAH(OVERALL HEIGHT)
TS
STEEL TRACK BRIDGEON
STEEL RUNWAYS
ALUMINUM TRACK BRIDGEON
STEEL RUNWAYS
* (4000# SYSTEMS ONLY)THE HEADER WELDMENT LOCATED AT THE TOP OF THE SUPPORT COLUMNS IS THE WIDEST PART OF THE SYSTEM.
**CS = BRIDGE LENGTH (L) + 4”
L1
L1
L7
RUNWAY LENGTHBRIDGE LENGTH (L)
**CS(CLEAR SPAN)
*OAW(OVERALL WIDTH)
OAH(OVERALL HEIGHT) TS
D
D+6
D+3
D+3
COLUMN BASE DETAILFOR 3” COLUMNS
D
13”
10”
10”
COLUMN BASE DETAILFOR 6” & 7” COLUMNS
D
D+6
D+3 3/8
D+3 3/8
COLUMN BASE DETAILFOR 4” & 5” COLUMNS
FREE
STA
ND
ING
WO
RK
STAT
ION
CR
AN
ESFREE STANDING WORK STATION BRIDGE CRANESALUMINUM RUNWAYS WITH ALUMINUM BRIDGE
ISOMETRIC VIEW
3
Model Number:
Capacity: pounds
Bridge Length (L): (OAL)
Runway Length: (OAL)
Trolley Saddle Height: (TS)
L1: Are the number of support assemblies provided suffi cient?(See “SUPPORT” column on dimensional chart pages)
C: inches (hoist by others)
Gorbel® Free Standing Work Sta on Crane kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and aluminum systems), festoon stack-up sec on, splice joints and hanger brackets.
Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
L1
L1
L7
RUNWAY LENGTH
BRIDGE LENGTH (L)
**CS(CLEAR SPAN)
*OAW(OVERALL WIDTH)
OAH(OVERALL HEIGHT) TS
ALUMINUM TRACK BRIDGEON
ALUMINUM RUNWAYS
D
D+6
D+3D+3
COLUMN BASE DETAIL3” COLUMNS
**CS = BRIDGE LENGTH (L) + 4
D
D+6
D+3 3/8D+3 3/8
COLUMN BASE DETAIL4” & 5” COLUMNS
FREE STA
ND
ING
WO
RK
STATION
CR
AN
ESFREE STANDING WORK STATION BRIDGE CRANES
STEEL RUNWAYS WITH STEEL OR ALUMINUM BRIDGE
4
Model Number:
Capacity: pounds
Bridge Length (L): (OAL)
Runway Length: (OAL)
Trolley Saddle Height: (TS)
L1: Are the number of support assemblies provided suffi cient?(See “SUPPORT” column on dimensional chart pages)
C: inches (hoist by others)
Gorbel® Free Standing Work Sta on Crane kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and aluminum systems), festoon stack-up sec on, splice joints and hanger brackets.
Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
STEEL TRACK BRIDGE ON STEEL RUNWAYS
END VIEW
TS
*OAH
L3
L5**
HOIST TROLLEY
CS
H4 CL6
L5**
H3
*OAH INCLUDES ALL HARDWARE
ALUMINUM TRACK BRIDGE ON STEEL RUNWAYS
END VIEW
TS
*OAHL3
L5**
HOIST TROLLEY
CS
H4 C L6
L5**
H3A
*OAH INCLUDES ALL HARDWARE
COPED ALUMINUM TRACK BRIDGE ON STEEL RUNWAYS
END VIEW
TS
*OAH
L3
L5**
HOIST TROLLEY
CS
H4 C L6
L5**
SEE NOTE
*OAH INCLUDES ALL HARDWARETo fi nd OAH when using an Alumium bridge:
(H3A - H3) + OAH steel bridge
Note: 250 SERIES = H3A - 3.25” 500 SERIES = H3A - 5.12”1000 SERIES = H3A2000 SERIES = H3A4000 SERIES = H3A
D+6”
D+6”
D+3 3/8”
D+3 3/8”
BASE BOLT PATTERNFOR 4” & 5” COLUMNS
D+6”
D+6”
D+3”
D+3”
BASE BOLT PATTERNFOR 3” COLUMNS 4X Ø1”
HOLE
4X Ø1” HOLE
13”
13”
10”
10”
BASE BOLT PATTERNFOR 6” & 7” COLUMNS 4X Ø1”
HOLE
L8
L1
RUNWAY LENGTH48” MAXENDTRUCK
L1
D
L7L8
SPLICE JOINT AND PLATE
BRIDGE SPAN (L4)**
BRIDGE LENGTH
(L) OAW
SIDE VIEW
TOP VIEW
FREE STANDING WORK STATION BRIDGE CRANESALUMINUM BRIDGE ON ALUMINUM RUNWAYS
Model Number:
Capacity: pounds
Bridge Length (L): (OAL)
Runway Length: (OAL)
Trolley Saddle Height: (TS)
L1: Are the number of support assemblies provided suffi cient?(See “SUPPORT” column on dimensional chart pages)
C: inches (hoist by others)
Gorbel® Free Standing Work Sta on Crane kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and aluminum systems), festoon stack-up sec on, splice joints and hanger brackets.
Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
FREE
STA
ND
ING
WO
RK
STAT
ION
CR
AN
ES
5
ALUMINUM TRACK BRIDGE
END VIEW
TS*OAH
L3
L5**
HOIST TROLLEY
CS
H4 C L6
L5**
H3
*OAH INCLUDES ALL HARDWARE
COPED ALUMINUM TRACK BRIDGE
END VIEW
TS*OAH
L3
L5**
HOIST TROLLEY
CS
H4 C L6
L5**
SEE NOTE BELOW
*OAH INCLUDES ALL HARDWARE
Note: 250 SERIES = H3 - 3.25” 500 SERIES = H3 - 5.12”1000 SERIES = H32000 SERIES = H34000 SERIES = H3
D+6”
D+6”
D+3 3/8”
D+3 3/8”
BASE BOLT PATTERNFOR 4” & 5” COLUMNS
D+6”
D+6”
D+3”
D+3”
BASE BOLT PATTERNFOR 3” COLUMNS 4X Ø1”
HOLE
4X Ø1” HOLE
L8
L1
RUNWAY LENGTH
48” MAXENDTRUCK
L1
D
L7L8
SPLICE JOINTS
BRIDGE SPAN (L4)**
BRIDGE LENGTH
(L) OAW
SIDE VIEW
TOP VIEW
FREE STANDING WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTURE
MAX. L1
L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
10’
11’-6”10’12’14’
GLCS-FS-250-10 (S or AL)-11.5-10GLCS-FS-250-10 (S or AL)-11.5-12GLCS-FS-250-10 (S or AL)-11.5-14
SteelSteelSteel
20’20’20’
999
10 3/410 3/410 3/4
12 7/812 7/812 7/8
20 5/820 5/820 5/8
4 3/44 3/44 3/4
5 1/85 1/85 1/8
8 3/48 3/48 3/4
11’-4”11’-4”11’-4”
11’-5 3/8”13’-5 3/8”15’-5 3/8”
333
222
23’
10’10’12’12’14’14’
GLCS-FS-250-10 (S or AL)-23-10AL-FS-250-10-23-10
GLCS-FS-250-10 (S or AL)-23-12AL-FS-250-10-23-12
GLCS-FS-250-10 (S or AL)-23-14AL-FS-250-10-23-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9139
139
13
10 3/413 1/410 3/413 1/410 3/413 1/4
12 7/820
12 7/820
12 7/820
20 5/8-
20 5/8-
20 5/8-
4 3/410 3/44 3/4
10 3/44 3/4
10 3/4
5 1/87 1/45 1/87 1/45 1/87 1/4
8 3/416 7/88 3/4
16 7/88 3/4
16 7/8
11’-4”11’-4”11’-4”11’-4”11’-4”11’-4”
11’-5 3/8”12’-0 1/2”13’-5 3/8”14’-0 1/2”15’-5 3/8”16’-0 1/2”
333333
222222
28’10’12’14’
GLCSL-FS-250-10 (S or AL)-28-10GLCSL-FS-250-10 (S or AL)-28-12GLCSL-FS-250-10 (S or AL)-28-14
SteelSteelSteel
25’25’25’
999
10 3/410 3/410 3/4
14 7/814 7/814 7/8
22 5/822 5/822 5/8
4 3/44 3/44 3/4
5 1/85 1/85 1/8
8 3/48 3/48 3/4
11’-4”11’-4”11’-4”
11’-7 3/8”13’-7 3/8”15’-7 3/8”
333
222
33’
10’10’12’12’14’14’
GLCS-FS-250-10 (S or AL)-33-10AL-FS-250-10-33-10
GLCS-FS-250-10 (S or AL)-33-12AL-FS-250-10-33-12
GLCS-FS-250-10 (S or AL)-33-14AL-FS-250-10-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9199
199
19
10 3/413 1/410 3/413 1/410 3/413 1/4
12 7/820
12 7/820
12 7/820
20 5/8-
20 5/8-
20 5/8-
4 3/410 3/44 3/4
10 3/44 3/4
10 3/4
5 1/87 1/45 1/87 1/45 1/87 1/4
8 3/416 7/88 3/4
16 7/88 3/4
16 7/8
11’-4”11’-4”11’-4”11’-4”11’-4”11’-4”
11’-5 3/8”12’-0 1/2”13’-5 3/8”14’-0 1/2”15’-5 3/8”16’-0 1/2”
333333
333333
43’
10’10’12’12’14’14’
GLCS-FS-250-10 (S or AL)-43-10AL-FS-250-10-43-10
GLCS-FS-250-10 (S or AL)-43-12AL-FS-250-10-43-12
GLCS-FS-250-10 (S or AL)-43-14AL-FS-250-10-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
132613261326
10 3/413 1/410 3/413 1/410 3/413 1/4
12 7/820
12 7/820
12 7/820
20 5/8-
20 5/8-
20 5/8-
4 3/410 3/44 3/4
10 3/44 3/4
10 3/4
5 1/87 1/45 1/87 1/45 1/87 1/4
8 3/416 7/88 3/4
16 7/88 3/4
16 7/8
11’-4”11’-4”11’-4”11’-4”11’-4”11’-4”
11’-5 3/8”12’-0 1/2”13’-5 3/8”14’-0 1/2”15’-5 3/8”16’-0 1/2”
333333
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-250-10 (S or AL)-53-10AL-FS-250-10-53-10
GLCSL-FS-250-10 (S or AL)-53-10GLCS-FS-250-10 (S or AL)-53-12
AL-FS-250-10-53-12GLCSL-FS-250-10 (S or AL)-53-12GLCS-FS-250-10 (S or AL)-53-14
AL-FS-250-10-53-14GLCSL-FS-250-10 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
133013133013133013
10 3/413 1/410 3/410 3/413 1/410 3/410 3/413 1/410 3/4
12 7/820
14 7/812 7/8
2014 7/812 7/8
2014 7/8
20 5/8-
22 5/820 5/8
-22 5/820 5/8
-22 5/8
4 3/410 3/44 3/44 3/4
10 3/44 3/44 3/4
10 3/44 3/4
5 1/87 1/45 1/85 1/87 1/45 1/85 1/87 1/45 1/8
8 3/416 7/88 3/48 3/4
16 7/88 3/48 3/4
16 7/88 3/4
11’-4”11’-4”11’-4”11’-4”11’-4”11’-4”11’-4”11’-4”11’-4”
11’-5 3/8”12’-0 1/2”11’-7 3/8”13’-5 3/8”14’-0 1/2”13’-7 3/8”15’-5 3/8”16’-0 1/2”15’-7 3/8”
333333333
443443443
63’
10’10’12’12’14’14’
GLCS-FS-250-10 (S or AL)-63-10AL-FS-250-10-63-10
GLCS-FS-250-10 (S or AL)-63-12AL-FS-250-10-63-12
GLCS-FS-250-10 (S or AL)-63-14AL-FS-250-10-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
193619361936
10 3/413 1/410 3/413 1/410 3/413 1/4
12 7/820
12 7/820
12 7/820
20 5/8-
20 5/8-
20 5/8-
4 3/410 3/44 3/4
10 3/44 3/4
10 3/4
5 1/87 1/45 1/87 1/45 1/87 1/4
8 3/416 7/88 3/4
16 7/88 3/4
16 7/8
11’-4”11’-4”11’-4”11’-4”11’-4”11’-4”
11’-5 3/8”12’-0 1/2”13’-5 3/8”14’-0 1/2”15’-5 3/8”16’-0 1/2”
333333
444444
78’10’12’14’
GLCSL-FS-250-10 (S or AL)-78-10GLCSL-FS-250-10 (S or AL)-78-12GLCSL-FS-250-10 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
10 3/410 3/410 3/4
14 7/814 7/814 7/8
22 5/822 5/822 5/8
4 3/44 3/44 3/4
5 1/85 1/85 1/8
15 1/815 1/815 1/8
11’-4”11’-4”11’-4”
11’-7 3/8”13’-7 3/8”15’-7 3/8”
333
444
83’
10’10’12’12’14’14’
GLCS-FS-250-10 (S or AL)-83-10AL-FS-250-10-83-10
GLCS-FS-250-10 (S or AL)-83-12AL-FS-250-10-83-12
GLCS-FS-250-10 (S or AL)-83-14AL-FS-250-10-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
10 3/413 1/410 3/413 1/410 3/413 1/4
12 7/820
12 7/820
12 7/820
20 5/8-
20 5/8-
20 5/8-
4 3/410 3/44 3/4
10 3/44 3/4
10 3/4
5 1/87 1/45 1/87 1/45 1/87 1/4
15 1/816 7/815 1/816 7/815 1/816 7/8
11’-4”11’-4”11’-4”11’-4”11’-4”11’-4”
11’-5 3/8”12’-0 1/2”13’-5 3/8”14’-0 1/2”15’-5 3/8”16’-0 1/2”
333333
555555
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-250-10 (S or AL)-103-10AL-FS-250-10-103-10
GLCSL-FS-250-10 (S or AL)-103-10GLCS-FS-250-10 (S or AL)-103-12
AL-FS-250-10-103-12GLCSL-FS-250-10 (S or AL)-103-12GLCS-FS-250-10 (S or AL)-103-14
AL-FS-250-10-103-14GLCSL-FS-250-10 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
10 3/413 1/410 3/410 3/413 1/410 3/410 3/413 1/410 3/4
12 7/820
14 7/812 7/8
2014 7/812 7/8
2014 7/8
20 5/8-
22 5/820 5/8
-22 5/820 5/8
-22 5/8
4 3/410 3/44 3/44 3/4
10 3/44 3/44 3/4
10 3/44 3/4
5 1/87 1/45 1/85 1/87 1/45 1/85 1/87 1/45 1/8
15 1/816 7/815 1/815 1/816 7/815 1/815 1/816 7/815 1/8
11’-4”11’-4”11’-4”11’-4”11’-4”11’-4”11’-4”11’-4”11’-4”
11’-5 3/8”12’-0 1/2”11’-7 3/8”13’-5 3/8”14’-0 1/2”13’-7 3/8”15’-5 3/8”16’-0 1/2”15’-7 3/8”
333333333
665665665
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
FREE STA
ND
ING
WO
RK
STATION
CR
AN
ES
6
250# CAPACITY
FREE STANDING WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTURE
MAX. L1
L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
15’
23’
10’10’12’12’14’14’
GLCS-FS-250-15 (S or AL)-23-10AL-FS-250-15-23-10
GLCS-FS-250-15 (S or AL)-23-12AL-FS-250-15-23-12
GLCS-FS-250-15 (S or AL)-23-14AL-FS-250-15-23-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9139
139
13
10 3/413 1/410 3/413 1/410 3/413 1/4
12 7/820
12 7/820
12 7/820
20 5/8-
20 5/8-
20 5/8-
10 1/210 3/410 1/210 3/410 1/210 3/4
5 1/87 1/45 1/87 1/45 1/87 1/4
11 1/423 5/811 1/423 5/811 1/423 5/8
16’-4”16’-4”16’-4”16’-4”16’-4”16’-4”
11’-5 3/8”12’-0 1/2”13’-5 3/8”14’-0 1/2”15’-5 3/8”16’-0 1/2”
333333
222222
28’10’12’14’
GLCSL-FS-250-15 (S or AL)-28-10GLCSL-FS-250-15 (S or AL)-28-12GLCSL-FS-250-15 (S or AL)-28-14
SteelSteelSteel
25’25’25’
999
10 3/410 3/410 3/4
14 7/814 7/814 7/8
22 5/822 5/822 5/8
10 1/210 1/210 1/2
5 1/85 1/85 1/8
11 1/411 1/411 1/4
16’-4”16’-4”16’-4”
11’-7 3/8”13’-7 3/8”15’-7 3/8”
333
222
33’
10’10’12’12’14’14’
GLCS-FS-250-15 (S or AL)-33-10AL-FS-250-15-33-10
GLCS-FS-250-15 (S or AL)-33-12AL-FS-250-15-33-12
GLCS-FS-250-15 (S or AL)-33-14AL-FS-250-15-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9199
199
19
10 3/413 1/410 3/413 1/410 3/413 1/4
12 7/820
12 7/820
12 7/820
20 5/8-
20 5/8-
20 5/8-
10 1/210 3/410 1/210 3/410 1/210 3/4
5 1/87 1/45 1/87 1/45 1/87 1/4
11 1/423 5/811 1/423 5/811 1/423 5/8
16’-4”16’-4”16’-4”16’-4”16’-4”16’-4”
11’-5 3/8”12’-0 1/2”13’-5 3/8”14’-0 1/2”15’-5 3/8”16’-0 1/2”
333333
333333
43’
10’10’12’12’14’14’
GLCS-FS-250-15 (S or AL)-43-10AL-FS-250-15-43-10
GLCS-FS-250-15 (S or AL)-43-12AL-FS-250-15-43-12
GLCS-FS-250-15 (S or AL)-43-14AL-FS-250-15-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
112611261126
10 3/413 1/410 3/413 1/410 3/413 1/4
12 7/820
12 7/820
12 7/820
20 5/8-
20 5/8-
20 5/8-
10 1/210 3/410 1/210 3/410 1/210 3/4
5 1/87 1/45 1/87 1/45 1/87 1/4
11 1/423 5/811 1/423 5/811 1/423 5/8
16’-4”16’-4”16’-4”16’-4”16’-4”16’-4”
11’-5 3/8”12’-0 1/2”13’-5 3/8”14’-0 1/2”15’-5 3/8”16’-0 1/2”
333333
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-250-15 (S or AL)-53-10AL-FS-250-15-53-10
GLCSL-FS-250-15 (S or AL)-53-10GLCS-FS-250-15 (S or AL)-53-12
AL-FS-250-15-53-12GLCSL-FS-250-15 (S or AL)-53-12GLCS-FS-250-15 (S or AL)-53-14
AL-FS-250-15-53-14GLCSL-FS-250-15 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
133013133013133013
10 3/413 1/410 3/410 3/413 1/410 3/410 3/413 1/410 3/4
12 7/820
14 7/812 7/8
2014 7/812 7/8
2014 7/8
20 5/8-
22 5/820 5/8
-22 5/820 5/8
-22 5/8
10 1/210 3/410 1/210 1/210 3/410 1/210 1/210 3/410 1/2
5 1/87 1/45 1/85 1/87 1/45 1/85 1/87 1/45 1/8
11 1/423 5/811 1/411 1/423 5/811 1/411 1/423 5/811 1/4
16’-4”16’-4”16’-4”16’-4”16’-4”16’-4”16’-4”16’-4”16’-4”
11’-5 3/8”12’-0 1/2”11’-7 3/8”13’-5 3/8”14’-0 1/2”13’-7 3/8”15’-5 3/8”16’-0 1/2”15’-7 3/8”
333333333
443443443
63’
10’10’12’12’14’14’
GLCS-FS-250-15 (S or AL)-63-10AL-FS-250-15-63-10
GLCS-FS-250-15 (S or AL)-63-12AL-FS-250-15-63-12
GLCS-FS-250-15 (S or AL)-63-14AL-FS-250-15-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
153615361536
10 3/413 1/410 3/413 1/410 3/413 1/4
12 7/820
12 7/820
12 7/820
20 5/8-
20 5/8-
20 5/8-
10 1/210 3/410 1/210 3/410 1/210 3/4
5 1/87 1/45 1/87 1/45 1/87 1/4
11 1/423 5/811 1/423 5/811 1/423 5/8
16’-4”16’-4”16’-4”16’-4”16’-4”16’-4”
11’-5 3/8”12’-0 1/2”13’-5 3/8”14’-0 1/2”15’-5 3/8”16’-0 1/2”
333333
444444
78’10’12’14’
GLCSL-FS-250-15 (S or AL)-78-10GLCSL-FS-250-15 (S or AL)-78-12GLCSL-FS-250-15 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
10 3/410 3/410 3/4
14 7/814 7/814 7/8
22 5/822 5/822 5/8
10 1/210 1/210 1/2
5 1/85 1/85 1/8
21 7/821 7/821 7/8
16’-4”16’-4”16’-4”
11’-7 3/8”13’-7 3/8”15’-7 3/8”
333
444
83’
10’10’12’12’14’14’
GLCS-FS-250-15 (S or AL)-83-10AL-FS-250-15-83-10
GLCS-FS-250-15 (S or AL)-83-12AL-FS-250-15-83-12
GLCS-FS-250-15 (S or AL)-83-14AL-FS-250-15-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
10 3/413 1/410 3/413 1/410 3/413 1/4
12 7/820
12 7/820
12 7/820
20 5/8-
20 5/8-
20 5/8-
10 1/210 3/410 1/210 3/410 1/210 3/4
5 1/87 1/45 1/87 1/45 1/87 1/4
21 7/823 5/821 7/823 5/821 7/823 5/8
16’-4”16’-4”16’-4”16’-4”16’-4”16’-4”
11’-5 3/8”12’-0 1/2”13’-5 3/8”14’-0 1/2”15’-5 3/8”16’-0 1/2”
333333
555555
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-250-15 (S or AL)-103-10AL-FS-250-15-103-10
GLCSL-FS-250-15 (S or AL)-103-10GLCS-FS-250-15 (S or AL)-103-12
AL-FS-250-15-103-12GLCSL-FS-250-15 (S or AL)-103-12GLCS-FS-250-15 (S or AL)-103-14
AL-FS-250-15-103-14GLCSL-FS-250-15 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
10 3/413 1/410 3/410 3/413 1/410 3/410 3/413 1/410 3/4
12 7/820
14 7/812 7/8
2014 7/812 7/8
2014 7/8
20 5/8-
22 5/820 5/8
-22 5/820 5/8
-22 5/8
10 1/210 3/410 1/210 1/210 3/410 1/210 1/210 3/410 1/2
5 1/87 1/45 1/85 1/87 1/45 1/85 1/87 1/45 1/8
21 7/823 5/821 7/821 7/823 5/821 7/821 7/823 5/821 7/8
16’-4”16’-4”16’-4”16’-4”16’-4”16’-4”16’-4”16’-4”16’-4”
11’-5 3/8”12’-0 1/2”11’-7 3/8”13’-5 3/8”14’-0 1/2”13’-7 3/8”15’-5 3/8”16’-0 1/2”15’-7 3/8”
333333333
665665665
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
250# CAPACITYFR
EE S
TAN
DIN
G W
OR
KST
ATIO
N C
RA
NES
7
FREE STANDING WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTURE
MAX. L1
L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
20’
23’
10’10’12’12’14’14’
GLCS-FS-250-20 (S or AL)-23-10AL-FS-250-20-23-10
GLCS-FS-250-20 (S or AL)-23-12AL-FS-250-20-23-12
GLCS-FS-250-20 (S or AL)-23-14AL-FS-250-20-23-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9139
139
13
10 3/413 1/410 3/413 1/410 3/413 1/4
12 7/820
12 7/820
12 7/820
20 5/8-
20 5/8-
20 5/8-
10 1/210 3/410 1/210 3/410 1/210 3/4
5 1/87 1/45 1/87 1/45 1/87 1/4
19 1/227
19 1/227
19 1/227
21’-4”21’-4”21’-4”21’-4”21’-4”21’-4”
11’-5 3/8”12’-0 1/2”13’-5 3/8”14’-0 1/2”15’-5 3/8”16’-0 1/2”
333333
222222
28’10’12’14’
GLCSL-FS-250-20 (S or AL)-28-10GLCSL-FS-250-20 (S or AL)-28-12GLCSL-FS-250-20 (S or AL)-28-14
SteelSteelSteel
25’25’25’
999
10 3/410 3/410 3/4
14 7/814 7/814 7/8
22 5/822 5/822 5/8
10 1/210 1/210 1/2
5 1/85 1/85 1/8
19 1/219 1/219 1/2
21’-4”21’-4”21’-4”
11’-7 3/8”13’-7 3/8”15’-7 3/8”
333
222
33’
10’10’12’12’14’14’
GLCS-FS-250-20 (S or AL)-33-10AL-FS-250-20-33-10
GLCS-FS-250-20 (S or AL)-33-12AL-FS-250-20-33-12
GLCS-FS-250-20 (S or AL)-33-14AL-FS-250-20-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9199
199
19
10 3/413 1/410 3/413 1/410 3/413 1/4
12 7/820
12 7/820
12 7/820
20 5/8-
20 5/8-
20 5/8-
10 1/210 3/410 1/210 3/410 1/210 3/4
5 1/87 1/45 1/87 1/45 1/87 1/4
19 1/227
19 1/227
19 1/227
21’-4”21’-4”21’-4”21’-4”21’-4”21’-4”
11’-5 3/8”12’-0 1/2”13’-5 3/8”14’-0 1/2”15’-5 3/8”16’-0 1/2”
333333
333333
43’
10’10’12’12’14’14’
GLCS-FS-250-20 (S or AL)-43-10AL-FS-250-20-43-10
GLCS-FS-250-20 (S or AL)-43-12AL-FS-250-20-43-12
GLCS-FS-250-20 (S or AL)-43-14AL-FS-250-20-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
112611261126
10 3/413 1/410 3/413 1/410 3/413 1/4
12 7/820
12 7/820
12 7/820
20 5/8-
20 5/8-
20 5/8-
10 1/210 3/410 1/210 3/410 1/210 3/4
5 1/87 1/45 1/87 1/45 1/87 1/4
19 1/227
19 1/227
19 1/227
21’-4”21’-4”21’-4”21’-4”21’-4”21’-4”
11’-5 3/8”12’-0 1/2”13’-5 3/8”14’-0 1/2”15’-5 3/8”16’-0 1/2”
333333
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-250-20 (S or AL)-53-10AL-FS-250-20-53-10
GLCSL-FS-250-20 (S or AL)-53-10GLCS-FS-250-20 (S or AL)-53-12
AL-FS-250-20-53-12GLCSL-FS-250-20 (S or AL)-53-12GLCS-FS-250-20 (S or AL)-53-14
AL-FS-250-20-53-14GLCSL-FS-250-20 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
133013133013133013
10 3/413 1/410 3/410 3/413 1/410 3/410 3/413 1/410 3/4
12 7/820
14 7/812 7/8
2014 7/812 7/8
2014 7/8
20 5/8-
22 5/820 5/8
-22 5/820 5/8
-22 5/8
10 1/210 3/410 1/210 1/210 3/410 1/210 1/210 3/410 1/2
5 1/87 1/45 1/85 1/87 1/45 1/85 1/87 1/45 1/8
19 1/227
19 1/219 1/2
2719 1/219 1/2
2719 1/2
21’-4”21’-4”21’-4”21’-4”21’-4”21’-4”21’-4”21’-4”21’-4”
11’-5 3/8”12’-0 1/2”11’-7 3/8”13’-5 3/8”14’-0 1/2”13’-7 3/8”15’-5 3/8”16’-0 1/2”15’-7 3/8”
333333333
443443443
63’
10’10’12’12’14’14’
GLCS-FS-250-20 (S or AL)-63-10AL-FS-250-20-63-10
GLCS-FS-250-20 (S or AL)-63-12AL-FS-250-20-63-12
GLCS-FS-250-20 (S or AL)-63-14AL-FS-250-20-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
153615361536
10 3/413 1/410 3/413 1/410 3/413 1/4
12 7/820
12 7/820
12 7/820
20 5/8-
20 5/8-
20 5/8-
10 1/210 3/410 1/210 3/410 1/210 3/4
5 1/87 1/45 1/87 1/45 1/87 1/4
19 1/227
19 1/227
19 1/227
21’-4”21’-4”21’-4”21’-4”21’-4”21’-4”
11’-5 3/8”12’-0 1/2”13’-5 3/8”14’-0 1/2”15’-5 3/8”16’-0 1/2”
333333
444444
78’10’12’14’
GLCSL-FS-250-20 (S or AL)-78-10GLCSL-FS-250-20 (S or AL)-78-12GLCSL-FS-250-20 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
10 3/410 3/410 3/4
14 7/814 7/814 7/8
22 5/822 5/822 5/8
10 1/210 1/210 1/2
5 1/85 1/85 1/8
25 1/425 1/425 1/4
21’-4”21’-4”21’-4”
11’-7 3/8”13’-7 3/8”15’-7 3/8”
333
444
83’
10’10’12’12’14’14’
GLCS-FS-250-20 (S or AL)-83-10AL-FS-250-20-83-10
GLCS-FS-250-20 (S or AL)-83-12AL-FS-250-20-83-12
GLCS-FS-250-20 (S or AL)-83-14AL-FS-250-20-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
10 3/413 1/410 3/413 1/410 3/413 1/4
12 7/820
12 7/820
12 7/820
20 5/8-
20 5/8-
20 5/8-
10 1/210 3/410 1/210 3/410 1/210 3/4
5 1/87 1/45 1/87 1/45 1/87 1/4
25 1/427
25 1/427
25 1/427
21’-4”21’-4”21’-4”21’-4”21’-4”21’-4”
11’-5 3/8”12’-0 1/2”13’-5 3/8”14’-0 1/2”15’-5 3/8”16’-0 1/2”
333333
555555
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-250-20 (S or AL)-103-10AL-FS-250-20-103-10
GLCSL-FS-250-20 (S or AL)-103-10GLCS-FS-250-20 (S or AL)-103-12
AL-FS-250-20-103-12GLCSL-FS-250-20 (S or AL)-103-12GLCS-FS-250-20 (S or AL)-103-14
AL-FS-250-20-103-14GLCSL-FS-250-20 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
10 3/413 1/410 3/410 3/413 1/410 3/410 3/413 1/410 3/4
12 7/820
14 7/812 7/8
2014 7/812 7/8
2014 7/8
20 5/8-
22 5/820 5/8
-22 5/820 5/8
-22 5/8
10 1/210 3/410 1/210 1/210 3/410 1/210 1/210 3/410 1/2
5 1/87 1/45 1/85 1/87 1/45 1/85 1/87 1/45 1/8
25 1/427
25 1/425 1/4
2725 1/425 1/4
2725 1/4
21’-4”21’-4”21’-4”21’-4”21’-4”21’-4”21’-4”21’-4”21’-4”
11’-5 3/8”12’-0 1/2”11’-7 3/8”13’-5 3/8”14’-0 1/2”13’-7 3/8”15’-5 3/8”16’-0 1/2”15’-7 3/8”
333333333
665665665
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
FREE STA
ND
ING
WO
RK
STATION
CR
AN
ES
8
250# CAPACITY
FREE STANDING WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTURE
MAX. L1
L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
23’
23’
10’10’12’12’14’14’
GLCS-FS-250-23 (S or AL)-23-10AL-FS-250-23-23-10
GLCS-FS-250-23 (S or AL)-23-12AL-FS-250-23-23-12
GLCS-FS-250-23 (S or AL)-23-14AL-FS-250-23-23-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9139
139
13
10 3/413 1/410 3/413 1/410 3/413 1/4
12 7/820
12 7/820
12 7/820
20 5/8-
20 5/8-
20 5/8-
10 1/210 3/410 1/210 3/410 1/210 3/4
5 1/87 1/45 1/87 1/45 1/87 1/4
19 1/230 3/819 1/230 3/819 1/230 3/8
24’-4”24’-4”24’-4”24’-4”24’-4”24’-4”
11’-5 3/8”12’-0 1/2”13’-5 3/8”14’-0 1/2”15’-5 3/8”16’-0 1/2”
333333
222222
28’10’12’14’
GLCSL-FS-250-23 (S or AL)-28-10GLCSL-FS-250-23 (S or AL)-28-12GLCSL-FS-250-23 (S or AL)-28-14
SteelSteelSteel
25’25’25’
999
10 3/410 3/410 3/4
14 7/814 7/814 7/8
22 5/822 5/822 5/8
10 1/210 1/210 1/2
5 1/85 1/85 1/8
19 1/219 1/219 1/2
24’-4”24’-4”24’-4”
11’-7 3/8”13’-7 3/8”15’-7 3/8”
333
222
33’
10’10’12’12’14’14’
GLCS-FS-250-23 (S or AL)-33-10AL-FS-250-23-33-10
GLCS-FS-250-23 (S or AL)-33-12AL-FS-250-23-33-12
GLCS-FS-250-23 (S or AL)-33-14AL-FS-250-23-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9199
199
19
10 3/413 1/410 3/413 1/410 3/413 1/4
12 7/820
12 7/820
12 7/820
20 5/8-
20 5/8-
20 5/8-
10 1/210 3/410 1/210 3/410 1/210 3/4
5 1/87 1/45 1/87 1/45 1/87 1/4
19 1/230 3/819 1/230 3/819 1/230 3/8
24’-4”24’-4”24’-4”24’-4”24’-4”24’-4”
11’-5 3/8”12’-0 1/2”13’-5 3/8”14’-0 1/2”15’-5 3/8”16’-0 1/2”
333333
333333
43’
10’10’12’12’14’14’
GLCS-FS-250-23 (S or AL)-43-10AL-FS-250-23-43-10
GLCS-FS-250-23 (S or AL)-43-12AL-FS-250-23-43-12
GLCS-FS-250-23 (S or AL)-43-14AL-FS-250-23-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
112611261126
10 3/413 1/410 3/413 1/410 3/413 1/4
12 7/820
12 7/820
12 7/820
20 5/8-
20 5/8-
20 5/8-
10 1/210 3/410 1/210 3/410 1/210 3/4
5 1/87 1/45 1/87 1/45 1/87 1/4
19 1/230 3/819 1/230 3/819 1/230 3/8
24’-4”24’-4”24’-4”24’-4”24’-4”24’-4”
11’-5 3/8”12’-0 1/2”13’-5 3/8”14’-0 1/2”15’-5 3/8”16’-0 1/2”
333333
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-250-23 (S or AL)-53-10AL-FS-250-23-53-10
GLCSL-FS-250-23 (S or AL)-53-10GLCS-FS-250-23 (S or AL)-53-12
AL-FS-250-23-53-12GLCSL-FS-250-23 (S or AL)-53-12GLCS-FS-250-23 (S or AL)-53-14
AL-FS-250-23-53-14GLCSL-FS-250-23 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
133013133013133013
10 3/413 1/410 3/410 3/413 1/410 3/410 3/413 1/410 3/4
12 7/820
14 7/812 7/8
2014 7/812 7/8
2014 7/8
20 5/8-
22 5/820 5/8
-22 5/820 5/8
-22 5/8
10 1/210 3/410 1/210 1/210 3/410 1/210 1/210 3/410 1/2
5 1/87 1/45 1/85 1/87 1/45 1/85 1/87 1/45 1/8
19 1/230 3/819 1/219 1/230 3/819 1/219 1/230 3/819 1/2
24’-4”24’-4”24’-4”24’-4”24’-4”24’-4”24’-4”24’-4”24’-4”
11’-5 3/8”12’-0 1/2”11’-7 3/8”13’-5 3/8”14’-0 1/2”13’-7 3/8”15’-5 3/8”16’-0 1/2”15’-7 3/8”
333333333
443443443
63’
10’10’12’12’14’14’
GLCS-FS-250-23 (S or AL)-63-10AL-FS-250-23-63-10
GLCS-FS-250-23 (S or AL)-63-12AL-FS-250-23-63-12
GLCS-FS-250-23 (S or AL)-63-14AL-FS-250-23-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
153615361536
10 3/413 1/410 3/413 1/410 3/413 1/4
12 7/820
12 7/820
12 7/820
20 5/8-
20 5/8-
20 5/8-
10 1/210 3/410 1/210 3/410 1/210 3/4
5 1/87 1/45 1/87 1/45 1/87 1/4
19 1/230 3/819 1/230 3/819 1/230 3/8
24’-4”24’-4”24’-4”24’-4”24’-4”24’-4”
11’-5 3/8”12’-0 1/2”13’-5 3/8”14’-0 1/2”15’-5 3/8”16’-0 1/2”
333333
444444
78’10’12’14’
GLCSL-FS-250-23 (S or AL)-78-10GLCSL-FS-250-23 (S or AL)-78-12GLCSL-FS-250-23 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
10 3/410 3/410 3/4
14 7/814 7/814 7/8
22 5/822 5/822 5/8
10 1/210 1/210 1/2
5 1/85 1/85 1/8
30 3/830 3/830 3/8
24’-4”24’-4”24’-4”
11’-7 3/8”13’-7 3/8”15’-7 3/8”
333
444
83’
10’10’12’12’14’14’
GLCS-FS-250-23 (S or AL)-83-10AL-FS-250-23-83-10
GLCS-FS-250-23 (S or AL)-83-12AL-FS-250-23-83-12
GLCS-FS-250-23 (S or AL)-83-14AL-FS-250-23-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
10 3/413 1/410 3/413 1/410 3/413 1/4
12 7/820
12 7/820
12 7/820
20 5/8-
20 5/8-
20 5/8-
10 1/210 3/410 1/210 3/410 1/210 3/4
5 1/87 1/45 1/87 1/45 1/87 1/4
30 3/830 3/830 3/830 3/830 3/830 3/8
24’-4”24’-4”24’-4”24’-4”24’-4”24’-4”
11’-5 3/8”12’-0 1/2”13’-5 3/8”14’-0 1/2”15’-5 3/8”16’-0 1/2”
333333
555555
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-250-23 (S or AL)-103-10AL-FS-250-23-103-10
GLCSL-FS-250-23 (S or AL)-103-10GLCS-FS-250-23 (S or AL)-103-12
AL-FS-250-23-103-12GLCSL-FS-250-23 (S or AL)-103-12GLCS-FS-250-23 (S or AL)-103-14
AL-FS-250-23-103-14GLCSL-FS-250-23 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
10 3/413 1/410 3/410 3/413 1/410 3/410 3/413 1/410 3/4
12 7/820
14 7/812 7/8
2014 7/812 7/8
2014 7/8
20 5/8-
22 5/820 5/8
-22 5/820 5/8
-22 5/8
10 1/210 3/410 1/210 1/210 3/410 1/210 1/210 3/410 1/2
5 1/87 1/45 1/85 1/87 1/45 1/85 1/87 1/45 1/8
30 3/830 3/830 3/830 3/830 3/830 3/830 3/830 3/830 3/8
24’-4”24’-4”24’-4”24’-4”24’-4”24’-4”24’-4”24’-4”24’-4”
11’-5 3/8”12’-0 1/2”11’-7 3/8”13’-5 3/8”14’-0 1/2”13’-7 3/8”15’-5 3/8”16’-0 1/2”15’-7 3/8”
333333333
665665665
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
250# CAPACITYFR
EE S
TAN
DIN
G W
OR
KST
ATIO
N C
RA
NES
9
FREE STANDING WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTURE
MAX. L1
L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
28’
23’
10’10’12’12’14’14’
GLCS-FS-250-28 (S or AL)-23-10AL-FS-250-28-23-10
GLCS-FS-250-28 (S or AL)-23-12AL-FS-250-28-23-12
GLCS-FS-250-28 (S or AL)-23-14AL-FS-250-28-23-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9139
139
13
21 3/423 3/821 3/423 3/821 3/423 3/8
15 1/424 3/815 1/424 3/815 1/424 3/8
25 1/4-
25 1/4-
25 1/4-
12 1/212 5/812 1/212 5/812 1/212 5/8
5 1/87 1/45 1/87 1/45 1/87 1/4
28 1/237 1/828 1/237 1/828 1/237 1/8
29’-4”29’-4”29’-4”29’-4”29’-4”29’-4”
11’-8 3/4”12’-5 7/8”13’-8 3/4”14’-5 7/8”15’-8 3/4”16’-5 7/8”
333333
222222
28’10’12’14’
GLCSL-FS-250-28 (S or AL)-28-10GLCSL-FS-250-28 (S or AL)-28-12GLCSL-FS-250-28 (S or AL)-28-14
SteelSteelSteel
25’25’25’
999
21 3/421 3/421 3/4
17 1/417 1/417 1/4
27 1/427 1/427 1/4
12 1/212 1/212 1/2
5 1/85 1/85 1/8
28 1/228 1/228 1/2
29’-4”29’-4”29’-4”
11’-10 3/4”13’-10 3/4”15’-10 3/4”
333
222
33’
10’10’12’12’14’14’
GLCS-FS-250-28 (S or AL)-33-10AL-FS-250-28-33-10
GLCS-FS-250-28 (S or AL)-33-12AL-FS-250-28-33-12
GLCS-FS-250-28 (S or AL)-33-14AL-FS-250-28-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9199
199
19
21 3/423 3/821 3/423 3/821 3/423 3/8
15 1/424 3/815 1/424 3/815 1/424 3/8
25 1/4-
25 1/4-
25 1/4-
12 1/212 5/812 1/212 5/812 1/212 5/8
5 1/87 1/45 1/87 1/45 1/87 1/4
28 1/237 1/828 1/237 1/828 1/237 1/8
29’-4”29’-4”29’-4”29’-4”29’-4”29’-4”
11’-8 3/4”12’-5 7/8”13’-8 3/4”14’-5 7/8”15’-8 3/4”16’-5 7/8”
333333
333333
43’
10’10’12’12’14’14’
GLCS-FS-250-28 (S or AL)-43-10AL-FS-250-28-43-10
GLCS-FS-250-28 (S or AL)-43-12AL-FS-250-28-43-12
GLCS-FS-250-28 (S or AL)-43-14AL-FS-250-28-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
112611261126
21 3/423 3/821 3/423 3/821 3/423 3/8
15 1/424 3/815 1/424 3/815 1/424 3/8
25 1/4-
25 1/4-
25 1/4-
12 1/212 5/812 1/212 5/812 1/212 5/8
5 1/87 1/45 1/87 1/45 1/87 1/4
28 1/237 1/828 1/237 1/828 1/237 1/8
29’-4”29’-4”29’-4”29’-4”29’-4”29’-4”
11’-8 3/4”12’-5 7/8”13’-8 3/4”14’-5 7/8”15’-8 3/4”16’-5 7/8”
333333
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-250-28 (S or AL)-53-10AL-FS-250-28-53-10
GLCSL-FS-250-28 (S or AL)-53-10GLCS-FS-250-28 (S or AL)-53-12
AL-FS-250-28-53-12GLCSL-FS-250-28 (S or AL)-53-12GLCS-FS-250-28 (S or AL)-53-14
AL-FS-250-28-53-14GLCSL-FS-250-28 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
133013133013133013
21 3/423 3/821 3/421 3/423 3/821 3/421 3/423 3/821 3/4
15 1/424 3/817 1/415 1/424 3/817 1/415 1/424 3/817 1/4
25 1/4-
27 1/425 1/4
-27 1/425 1/4
-27 1/4
12 1/212 5/812 1/212 1/212 5/812 1/212 1/212 5/812 1/2
5 1/87 1/45 1/85 1/87 1/45 1/85 1/87 1/45 1/8
28 1/237 1/828 1/228 1/237 1/828 1/228 1/237 1/828 1/2
29’-4”29’-4”29’-4”29’-4”29’-4”29’-4”29’-4”29’-4”29’-4”
11’-8 3/4”12’-5 7/8”
11’-10 3/4”13’-8 3/4”14’-5 7/8”
13’-10 3/4”15’-8 3/4”16’-5 7/8”
15’-10 3/4”
333333333
443443443
63’
10’10’12’12’14’14’
GLCS-FS-250-28 (S or AL)-63-10AL-FS-250-28-63-10
GLCS-FS-250-28 (S or AL)-63-12AL-FS-250-28-63-12
GLCS-FS-250-28 (S or AL)-63-14AL-FS-250-28-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
153615361536
21 3/423 3/821 3/423 3/821 3/423 3/8
15 1/424 3/815 1/424 3/815 1/424 3/8
25 1/4-
25 1/4-
25 1/4-
12 1/212 5/812 1/212 5/812 1/212 5/8
5 1/87 1/45 1/87 1/45 1/87 1/4
35 3/837 1/835 3/837 1/835 3/837 1/8
29’-4”29’-4”29’-4”29’-4”29’-4”29’-4”
11’-8 3/4”12’-5 7/8”13’-8 3/4”14’-5 7/8”15’-8 3/4”16’-5 7/8”
333333
444444
78’10’12’14’
GLCSL-FS-250-28 (S or AL)-78-10GLCSL-FS-250-28 (S or AL)-78-12GLCSL-FS-250-28 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
21 3/421 3/421 3/4
17 1/417 1/417 1/4
27 1/427 1/427 1/4
12 1/212 1/212 1/2
5 1/85 1/85 1/8
35 3/835 3/835 3/8
29’-4”29’-4”29’-4”
11’-10 3/4”13’-10 3/4”15’-10 3/4”
333
444
83’
10’10’12’12’14’14’
GLCS-FS-250-28 (S or AL)-83-10AL-FS-250-28-83-10
GLCS-FS-250-28 (S or AL)-83-12AL-FS-250-28-83-12
GLCS-FS-250-28 (S or AL)-83-14AL-FS-250-28-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
21 3/423 3/821 3/423 3/821 3/423 3/8
15 1/424 3/815 1/424 3/815 1/424 3/8
25 1/4-
25 1/4-
25 1/4-
12 1/212 5/812 1/212 5/812 1/212 5/8
5 1/87 1/45 1/87 1/45 1/87 1/4
35 3/837 1/835 3/837 1/835 3/837 1/8
29’-4”29’-4”29’-4”29’-4”29’-4”29’-4”
11’-8 3/4”12’-5 7/8”13’-8 3/4”14’-5 7/8”15’-8 3/4”16’-5 7/8”
333333
555555
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-250-28 (S or AL)-103-10AL-FS-250-28-103-10
GLCSL-FS-250-28 (S or AL)-103-10GLCS-FS-250-28 (S or AL)-103-12
AL-FS-250-28-103-12GLCSL-FS-250-28 (S or AL)-103-12GLCS-FS-250-28 (S or AL)-103-14
AL-FS-250-28-103-14GLCSL-FS-250-28 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
21 3/423 3/821 3/421 3/423 3/821 3/421 3/423 3/821 3/4
15 1/424 3/817 1/415 1/424 3/817 1/415 1/424 3/817 1/4
25 1/4-
27 1/425 1/4
-27 1/425 1/4
-27 1/4
12 1/212 5/812 1/212 1/212 5/812 1/212 1/212 5/812 1/2
5 1/87 1/45 1/85 1/87 1/45 1/85 1/87 1/45 1/8
35 3/837 1/835 3/835 3/837 1/835 3/835 3/837 1/835 3/8
29’-4”29’-4”29’-4”29’-4”29’-4”29’-4”29’-4”29’-4”29’-4”
11’-8 3/4”12’-5 7/8”
11’-10 3/4”13’-8 3/4”14’-5 7/8”
13’-10 3/4”15’-8 3/4”16’-5 7/8”
15’-10 3/4”
333333333
665665665
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
FREE STA
ND
ING
WO
RK
STATION
CR
AN
ES
10
250# CAPACITY
FREE STANDING WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
10’
11’-6”10’12’14’
GLCS-FS-500-10 (S or AL)-11.5-10GLCS-FS-500-10 (S or AL)-11.5-12GLCS-FS-500-10 (S or AL)-11.5-14
SteelSteelSteel
20’20’20’
999
13 1/813 1/813 1/8
16 1/216 1/216 1/2
242424
6 5/86 5/86 5/8
7 1/87 1/87 1/8
10 1/210 1/210 1/2
11’-4”11’-6”11’-6”
11’-9”13’-9”15’-9”
344
222
23’
10’10’12’12’14’14’
GLCS-FS-500-10 (S or AL)-23-10AL-FS-500-10-23-10
GLCS-FS-500-10 (S or AL)-23-12AL-FS-500-10-23-12
GLCS-FS-500-10 (S or AL)-23-14AL-FS-500-10-23-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9139
139
13
13 1/813 1/413 1/813 1/413 1/813 1/4
16 1/223 7/816 1/223 7/816 1/223 7/8
24-
24-
24-
6 5/812 5/86 5/8
12 5/86 5/8
12 5/8
7 1/87 1/47 1/87 1/47 1/87 1/4
10 1/216 7/810 1/216 7/810 1/216 7/8
11’-4”11’-4”11’-6”11’-6”11’-6”11’-6”
11’-9”12’-4 3/8”
13’-9”14’-4 3/8”
15’-9”16’-4 3/8”
334444
222222
28’10’12’14’
GLCSL-FS-500-10 (S or AL)-28-10GLCSL-FS-500-10 (S or AL)-28-12GLCSL-FS-500-10 (S or AL)-28-14
SteelSteelSteel
25’25’25’
999
13 1/813 1/813 1/8
18 7/818 7/818 7/8
26 3/826 3/826 3/8
6 5/86 5/86 5/8
7 1/87 1/87 1/8
10 1/210 1/210 1/2
11’-4”11’-6”11’-6”
11’-11 3/8”13’-11 3/8”15’-11 3/8”
344
222
33’
10’10’12’12’14’14’
GLCS-FS-500-10 (S or AL)-33-10AL-FS-500-10-33-10
GLCS-FS-500-10 (S or AL)-33-12AL-FS-500-10-33-12
GLCS-FS-500-10 (S or AL)-33-14AL-FS-500-10-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9199
199
19
13 1/813 1/413 1/813 1/413 1/813 1/4
16 1/223 7/816 1/223 7/816 1/223 7/8
24-
24-
24-
6 5/812 5/86 5/8
12 5/86 5/8
12 5/8
7 1/87 1/47 1/87 1/47 1/87 1/4
10 1/216 7/810 1/216 7/810 1/216 7/8
11’-4”11’-4”11’-6”11’-6”11’-6”11’-6”
11’-9”12’-4 3/8”
13’-9”14’-4 3/8”
15’-9”16’-4 3/8”
334444
333333
34’10’12’14’
GLCSLX-FS-500-10 (S or AL)-34-10GLCSLX-FS-500-10 (S or AL)-34-12GLCSLX-FS-500-10 (S or AL)-34-14
SteelSteelSteel
30’30’30’
999
13 1/813 1/813 1/8
20 7/820 7/820 7/8
28 3/828 3/828 3/8
6 5/86 5/86 5/8
7 1/87 1/87 1/8
10 1/210 1/210 1/2
11’-4”11’-6”11’-6”
12’-1 3/8”14’-1 3/8”16’-1 3/8”
344
222
43’
10’10’12’12’14’14’
GLCS-FS-500-10 (S or AL)-43-10AL-FS-500-10-43-10
GLCS-FS-500-10 (S or AL)-43-12AL-FS-500-10-43-12
GLCS-FS-500-10 (S or AL)-43-14AL-FS-500-10-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
112611261126
13 1/813 1/413 1/813 1/413 1/813 1/4
16 1/223 7/816 1/223 7/816 1/223 7/8
24-
24-
24-
6 5/812 5/86 5/8
12 5/86 5/8
12 5/8
7 1/87 1/47 1/87 1/47 1/87 1/4
10 1/216 7/810 1/216 7/810 1/216 7/8
11’-4”11’-4”11’-6”11’-6”11’-6”11’-6”
11’-9”12’-4 3/8”
13’-9”14’-4 3/8”
15’-9”16’-4 3/8”
334444
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-500-10 (S or AL)-53-10AL-FS-500-10-53-10
GLCSL-FS-500-10 (S or AL)-53-10GLCS-FS-500-10 (S or AL)-53-12
AL-FS-500-10-53-12GLCSL-FS-500-10 (S or AL)-53-12GLCS-FS-500-10 (S or AL)-53-14
AL-FS-500-10-53-14GLCSL-FS-500-10 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
133013133013133013
13 1/813 1/413 1/813 1/813 1/413 1/813 1/813 1/413 1/8
16 1/223 7/818 7/816 1/223 7/818 7/816 1/223 7/818 7/8
24-
26 3/824-
26 3/824-
26 3/8
6 5/812 5/86 5/86 5/8
12 5/86 5/86 5/8
12 5/86 5/8
7 1/87 1/47 1/87 1/87 1/47 1/87 1/87 1/47 1/8
10 1/216 7/810 1/210 1/216 7/810 1/210 1/216 7/810 1/2
11’-4”11’-4”11’-4”11’-6”11’-6”11’-6”11’-6”11’-6”11’-6”
11’-9”12’-4 3/8”
11’-11 3/8”13’-9”
14’-4 3/8”13’-11 3/8”
15’-9”16’-4 3/8”
15’-11 3/8”
333444444
443443443
63’
10’10’12’12’14’14’
GLCS-FS-500-10 (S or AL)-63-10AL-FS-500-10-63-10
GLCS-FS-500-10 (S or AL)-63-12AL-FS-500-10-63-12
GLCS-FS-500-10 (S or AL)-63-14AL-FS-500-10-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
153615361536
13 1/813 1/413 1/813 1/413 1/813 1/4
16 1/223 7/816 1/223 7/816 1/223 7/8
24-
24-
24-
6 5/812 5/86 5/8
12 5/86 5/8
12 5/8
7 1/87 1/47 1/87 1/47 1/87 1/4
10 1/216 7/810 1/216 7/810 1/216 7/8
11’-4”11’-4”11’-6”11’-6”11’-6”11’-6”
11’-9”12’-4 3/8”
13’-9”14’-4 3/8”
15’-9”16’-4 3/8”
334444
444444
64’10’12’14’
GLCSLX-FS-500-10 (S or AL)-64-10GLCSLX-FS-500-10 (S or AL)-64-12GLCSLX-FS-500-10 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
13 1/813 1/813 1/8
20 7/820 7/820 7/8
28 3/828 3/828 3/8
6 5/86 5/86 5/8
7 1/87 1/87 1/8
16 7/816 7/816 7/8
11’-4”11’-6”11’-6”
12’-1 3/8”14’-1 3/8”16’-1 3/8”
344
333
78’10’12’14’
GLCSL-FS-500-10 (S or AL)-78-10GLCSL-FS-500-10 (S or AL)-78-12GLCSL-FS-500-10 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
13 1/813 1/813 1/8
18 7/818 7/818 7/8
26 3/826 3/826 3/8
6 5/86 5/86 5/8
7 1/87 1/87 1/8
16 7/816 7/816 7/8
11’-4”11’-6”11’-6”
11’-11 3/8”13’-11 3/8”15’-11 3/8”
344
444
83’
10’10’12’12’14’14’
GLCS-FS-500-10 (S or AL)-83-10AL-FS-500-10-83-10
GLCS-FS-500-10 (S or AL)-83-12AL-FS-500-10-83-12
GLCS-FS-500-10 (S or AL)-83-14AL-FS-500-10-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
13 1/813 1/413 1/813 1/413 1/813 1/4
16 1/223 7/816 1/223 7/816 1/223 7/8
24-
24-
24-
6 5/812 5/86 5/8
12 5/86 5/8
12 5/8
7 1/87 1/47 1/87 1/47 1/87 1/4
16 7/816 7/816 7/816 7/816 7/816 7/8
11’-4”11’-4”11’-6”11’-6”11’-6”11’-6”
11’-9”12’-4 3/8”
13’-9”14’-4 3/8”
15’-9”16’-4 3/8”
334444
555555
94’10’12’14’
GLCSLX-FS-500-10 (S or AL)-94-10GLCSLX-FS-500-10 (S or AL)-94-12GLCSLX-FS-500-10 (S or AL)-94-14
SteelSteelSteel
30’30’30’
535353
13 1/813 1/813 1/8
20 7/820 7/820 7/8
28 3/828 3/828 3/8
6 5/86 5/86 5/8
7 1/87 1/87 1/8
16 7/816 7/816 7/8
11’-4”11’-6”11’-6”
12’-1 3/8”14’-1 3/8”16’-1 3/8”
344
444
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-500-10 (S or AL)-103-10AL-FS-500-10-103-10
GLCSL-FS-500-10 (S or AL)-103-10GLCS-FS-500-10 (S or AL)-103-12
AL-FS-500-10-103-12GLCSL-FS-500-10 (S or AL)-103-12GLCS-FS-500-10 (S or AL)-103-14
AL-FS-500-10-103-14GLCSL-FS-500-10 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
13 1/813 1/413 1/813 1/813 1/413 1/813 1/813 1/413 1/8
16 1/223 7/818 7/816 1/223 7/818 7/816 1/223 7/818 7/8
24-
26 3/824-
26 3/824-
26 3/8
6 5/812 5/86 5/86 5/8
12 5/86 5/86 5/8
12 5/86 5/8
7 1/87 1/47 1/87 1/87 1/47 1/87 1/87 1/47 1/8
16 7/816 7/816 7/816 7/816 7/816 7/816 7/816 7/816 7/8
11’-4”11’-4”11’-4”11’-6”11’-6”11’-6”11’-6”11’-6”11’-6”
11’-9”12’-4 3/8”
11’-11 3/8”13’-9”
14’-4 3/8”13’-11 3/8”
15’-9”16’-4 3/8”
15’-11 3/8”
333444444
665665665
124’10’12’14’
GLCSLX-FS-500-10 (S or AL)-124-10GLCSLX-FS-500-10 (S or AL)-124-12GLCSLX-FS-500-10 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
13 1/813 1/813 1/8
20 7/820 7/820 7/8
28 3/828 3/828 3/8
6 5/86 5/86 5/8
7 1/87 1/87 1/8
16 7/816 7/816 7/8
11’-4”11’-6”11’-6”
12’-1 3/8”14’-1 3/8”16’-1 3/8”
344
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
500# CAPACITYFR
EE S
TAN
DIN
G W
OR
KST
ATIO
N C
RA
NES
11
FREE STA
ND
ING
WO
RK
STATION
CR
AN
ES
12
500# CAPACITYFREE STANDING WORK STATION BRIDGE CRANES
BRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
15’
23’
10’10’12’12’14’14’
GLCS-FS-500-15 (S or AL)-23-10AL-FS-500-15-23-10
GLCS-FS-500-15 (S or AL)-23-12AL-FS-500-15-23-12
GLCS-FS-500-15 (S or AL)-23-14AL-FS-500-15-23-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9139
139
13
13 1/813 1/413 1/813 1/413 1/813 1/4
16 1/223 7/816 1/223 7/816 1/223 7/8
24-
24-
24-
12 3/412 5/812 3/412 5/812 3/412 5/8
7 1/87 1/47 1/87 1/47 1/87 1/4
21 3/423 5/821 3/423 5/821 3/423 5/8
16’-4”16’-4”16’-6”16’-6”16’-6”16’-6”
11’-9”12’-4 3/8”
13’-9”14’-4 3/8”
15’-9”16’-4 3/8”
334444
222222
28’10’12’14’
GLCSL-FS-500-15 (S or AL)-28-10GLCSL-FS-500-15 (S or AL)-28-12GLCSL-FS-500-15 (S or AL)-28-14
SteelSteelSteel
25’25’25’
999
13 1/813 1/813 1/8
18 7/818 7/818 7/8
26 3/826 3/826 3/8
12 3/412 3/412 3/4
7 1/87 1/87 1/8
21 3/421 3/421 3/4
16’-4”16’-6”16’-6”
11’-11 3/8”13’-11 3/8”15’-11 3/8”
344
222
33’
10’10’12’12’14’14’
GLCS-FS-500-15 (S or AL)-33-10AL-FS-500-15-33-10
GLCS-FS-500-15 (S or AL)-33-12AL-FS-500-15-33-12
GLCS-FS-500-15 (S or AL)-33-14AL-FS-500-15-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9199
199
19
13 1/813 1/413 1/813 1/413 1/813 1/4
16 1/223 7/816 1/223 7/816 1/223 7/8
24-
24-
24-
12 3/412 5/812 3/412 5/812 3/412 5/8
7 1/87 1/47 1/87 1/47 1/87 1/4
21 3/423 5/821 3/423 5/821 3/423 5/8
16’-4”16’-4”16’-6”16’-6”16’-6”16’-6”
11’-9”12’-4 3/8”
13’-9”14’-4 3/8”
15’-9”16’-4 3/8”
334444
333333
34’10’12’14’
GLCSLX-FS-500-15 (S or AL)-34-10GLCSLX-FS-500-15 (S or AL)-34-12GLCSLX-FS-500-15 (S or AL)-34-14
SteelSteelSteel
30’30’30’
999
13 1/813 1/813 1/8
20 7/820 7/820 7/8
28 3/828 3/828 3/8
12 3/412 3/412 3/4
7 1/87 1/87 1/8
21 3/421 3/421 3/4
16’-4”16’-6”16’-6”
12’-1 3/8”14’-1 3/8”16’-1 3/8”
344
222
43’
10’10’12’12’14’14’
GLCS-FS-500-15 (S or AL)-43-10AL-FS-500-15-43-10
GLCS-FS-500-15 (S or AL)-43-12AL-FS-500-15-43-12
GLCS-FS-500-15 (S or AL)-43-14AL-FS-500-15-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
132613261326
13 1/813 1/413 1/813 1/413 1/813 1/4
16 1/223 7/816 1/223 7/816 1/223 7/8
24-
24-
24-
12 3/412 5/812 3/412 5/812 3/412 5/8
7 1/87 1/47 1/87 1/47 1/87 1/4
21 3/423 5/821 3/423 5/821 3/423 5/8
16’-4”16’-4”16’-6”16’-6”16’-6”16’-6”
11’-9”12’-4 3/8”
13’-9”14’-4 3/8”
15’-9”16’-4 3/8”
334444
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-500-15 (S or AL)-53-10AL-FS-500-15-53-10
GLCSL-FS-500-15 (S or AL)-53-10GLCS-FS-500-15 (S or AL)-53-12
AL-FS-500-15-53-12GLCSL-FS-500-15 (S or AL)-53-12GLCS-FS-500-15 (S or AL)-53-14
AL-FS-500-15-53-14GLCSL-FS-500-15 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
133013133013133013
13 1/813 1/413 1/813 1/813 1/413 1/813 1/813 1/413 1/8
16 1/223 7/818 7/816 1/223 7/818 7/816 1/223 7/818 7/8
24-
26 3/824-
26 3/824-
26 3/8
12 3/412 5/812 3/412 3/412 5/812 3/412 3/412 5/812 3/4
7 1/87 1/47 1/87 1/87 1/47 1/87 1/87 1/47 1/8
21 3/423 5/821 3/421 3/423 5/821 3/421 3/423 5/821 3/4
16’-4”16’-4”16’-4”16’-6”16’-6”16’-6”16’-6”16’-6”16’-6”
11’-9”12’-4 3/8”
11’-11 3/8”13’-9”
14’-4 3/8”13’-11 3/8”
15’-9”16’-4 3/8”
15’-11 3/8”
333444444
443443443
63’
10’10’12’12’14’14’
GLCS-FS-500-15 (S or AL)-63-10AL-FS-500-15-63-10
GLCS-FS-500-15 (S or AL)-63-12AL-FS-500-15-63-12
GLCS-FS-500-15 (S or AL)-63-14AL-FS-500-15-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
193619361936
13 1/813 1/413 1/813 1/413 1/813 1/4
16 1/223 7/816 1/223 7/816 1/223 7/8
24-
24-
24-
12 3/412 5/812 3/412 5/812 3/412 5/8
7 1/87 1/47 1/87 1/47 1/87 1/4
21 3/423 5/821 3/423 5/821 3/423 5/8
16’-4”16’-4”16’-6”16’-6”16’-6”16’-6”
11’-9”12’-4 3/8”
13’-9”14’-4 3/8”
15’-9”16’-4 3/8”
334444
444444
64’10’12’14’
GLCSLX-FS-500-15 (S or AL)-64-10GLCSLX-FS-500-15 (S or AL)-64-12GLCSLX-FS-500-15 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
13 1/813 1/813 1/8
20 7/820 7/820 7/8
28 3/828 3/828 3/8
12 3/412 3/412 3/4
7 1/87 1/87 1/8
23 5/823 5/823 5/8
16’-4”16’-6”16’-6”
12’-1 3/8”14’-1 3/8”16’-1 3/8”
344
333
78’10’12’14’
GLCSL-FS-500-15 (S or AL)-78-10GLCSL-FS-500-15 (S or AL)-78-12GLCSL-FS-500-15 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
13 1/813 1/813 1/8
18 7/818 7/818 7/8
26 3/826 3/826 3/8
12 3/412 3/412 3/4
7 1/87 1/87 1/8
23 5/823 5/823 5/8
16’-4”16’-6”16’-6”
11’-11 3/8”13’-11 3/8”15’-11 3/8”
344
444
83’
10’10’12’12’14’14’
GLCS-FS-500-15 (S or AL)-83-10AL-FS-500-15-83-10
GLCS-FS-500-15 (S or AL)-83-12AL-FS-500-15-83-12
GLCS-FS-500-15 (S or AL)-83-14AL-FS-500-15-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
13 1/813 1/413 1/813 1/413 1/813 1/4
16 1/223 7/816 1/223 7/816 1/223 7/8
24-
24-
24-
12 3/412 5/812 3/412 5/812 3/412 5/8
7 1/87 1/47 1/87 1/47 1/87 1/4
23 5/823 5/823 5/823 5/823 5/823 5/8
16’-4”16’-4”16’-6”16’-6”16’-6”16’-6”
11’-9”12’-4 3/8”
13’-9”14’-4 3/8”
15’-9”16’-4 3/8”
334444
555555
94’10’12’14’
GLCSLX-FS-500-15 (S or AL)-94-10GLCSLX-FS-500-15 (S or AL)-94-12GLCSLX-FS-500-15 (S or AL)-94-14
SteelSteelSteel
30’30’30’
545454
13 1/813 1/813 1/8
20 7/820 7/820 7/8
28 3/828 3/828 3/8
12 3/412 3/412 3/4
7 1/87 1/87 1/8
23 5/823 5/823 5/8
16’-4”16’-6”16’-6”
12’-1 3/8”14’-1 3/8”16’-1 3/8”
344
444
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-500-15 (S or AL)-103-10AL-FS-500-15-103-10
GLCSL-FS-500-15 (S or AL)-103-10GLCS-FS-500-15 (S or AL)-103-12
AL-FS-500-15-103-12GLCSL-FS-500-15 (S or AL)-103-12GLCS-FS-500-15 (S or AL)-103-14
AL-FS-500-15-103-14GLCSL-FS-500-15 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
13 1/813 1/413 1/813 1/813 1/413 1/813 1/813 1/413 1/8
16 1/223 7/818 7/816 1/223 7/818 7/816 1/223 7/818 7/8
24-
26 3/824-
26 3/824-
26 3/8
12 3/412 5/812 3/412 3/412 5/812 3/412 3/412 5/812 3/4
7 1/87 1/47 1/87 1/87 1/47 1/87 1/87 1/47 1/8
23 5/823 5/823 5/823 5/823 5/823 5/823 5/823 5/823 5/8
16’-4”16’-4”16’-4”16’-6”16’-6”16’-6”16’-6”16’-6”16’-6”
11’-9”12’-4 3/8”
11’-11 3/8”13’-9”
14’-4 3/8”13’-11 3/8”
15’-9”16’-4 3/8”
15’-11 3/8”
333444444
665665665
124’10’12’14’
GLCSLX-FS-500-15 (S or AL)-124-10GLCSLX-FS-500-15 (S or AL)-124-12GLCSLX-FS-500-15 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
13 1/813 1/813 1/8
20 7/820 7/820 7/8
28 3/828 3/828 3/8
12 3/412 3/412 3/4
7 1/87 1/87 1/8
23 5/823 5/823 5/8
16’-4”16’-6”16’-6”
12’-1 3/8”14’-1 3/8”16’-1 3/8”
344
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
FREE STANDING WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
20’
23’
10’10’12’12’14’14’
GLCS-FS-500-20 (S or AL)-23-10AL-FS-500-20-23-10
GLCS-FS-500-20 (S or AL)-23-12AL-FS-500-20-23-12
GLCS-FS-500-20 (S or AL)-23-14AL-FS-500-20-23-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9139
139
13
13 1/813 1/413 1/813 1/413 1/813 1/4
16 1/223 7/816 1/223 7/816 1/223 7/8
24-
24-
24-
12 3/412 5/812 3/412 5/812 3/412 5/8
7 1/87 1/47 1/87 1/47 1/87 1/4
21 3/427
21 3/427
21 3/427
21’-4”21’-4”21’-6”21’-6”21’-6”21’-6”
11’-9”12’-4 3/8”
13’-9”14’-4 3/8”
15’-9”16’-4 3/8”
334444
222222
28’10’12’14’
GLCSL-FS-500-20 (S or AL)-28-10GLCSL-FS-500-20 (S or AL)-28-12GLCSL-FS-500-20 (S or AL)-28-14
SteelSteelSteel
25’25’25’
999
13 1/813 1/813 1/8
18 7/818 7/818 7/8
26 3/826 3/826 3/8
12 3/412 3/412 3/4
7 1/87 1/87 1/8
21 3/421 3/421 3/4
21’-4”21’-6”21’-6”
11’-11 3/8”13’-11 3/8”15’-11 3/8”
344
222
33’
10’10’12’12’14’14’
GLCS-FS-500-20 (S or AL)-33-10AL-FS-500-20-33-10
GLCS-FS-500-20 (S or AL)-33-12AL-FS-500-20-33-12
GLCS-FS-500-20 (S or AL)-33-14AL-FS-500-20-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9199
199
19
13 1/813 1/413 1/813 1/413 1/813 1/4
16 1/223 7/816 1/223 7/816 1/223 7/8
24-
24-
24-
12 3/412 5/812 3/412 5/812 3/412 5/8
7 1/87 1/47 1/87 1/47 1/87 1/4
21 3/427
21 3/427
21 3/427
21’-4”21’-4”21’-6”21’-6”21’-6”21’-6”
11’-9”12’-4 3/8”
13’-9”14’-4 3/8”
15’-9”16’-4 3/8”
334444
333333
34’10’12’14’
GLCSLX-FS-500-20 (S or AL)-34-10GLCSLX-FS-500-20 (S or AL)-34-12GLCSLX-FS-500-20 (S or AL)-34-14
SteelSteelSteel
30’30’30’
999
13 1/813 1/813 1/8
20 7/820 7/820 7/8
28 3/828 3/828 3/8
12 3/412 3/412 3/4
7 1/87 1/87 1/8
21 3/421 3/421 3/4
21’-4”21’-6”21’-6”
12’-1 3/8”14’-1 3/8”16’-1 3/8”
344
222
43’
10’10’12’12’14’14’
GLCS-FS-500-20 (S or AL)-43-10AL-FS-500-20-43-10
GLCS-FS-500-20 (S or AL)-43-12AL-FS-500-20-43-12
GLCS-FS-500-20 (S or AL)-43-14AL-FS-500-20-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
132613261326
13 1/813 1/413 1/813 1/413 1/813 1/4
16 1/223 7/816 1/223 7/816 1/223 7/8
24-
24-
24-
12 3/412 5/812 3/412 5/812 3/412 5/8
7 1/87 1/47 1/87 1/47 1/87 1/4
21 3/427
21 3/427
21 3/427
21’-4”21’-4”21’-6”21’-6”21’-6”21’-6”
11’-9”12’-4 3/8”
13’-9”14’-4 3/8”
15’-9”16’-4 3/8”
334444
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-500-20 (S or AL)-53-10AL-FS-500-20-53-10
GLCSL-FS-500-20 (S or AL)-53-10GLCS-FS-500-20 (S or AL)-53-12
AL-FS-500-20-53-12GLCSL-FS-500-20 (S or AL)-53-12GLCS-FS-500-20 (S or AL)-53-14
AL-FS-500-20-53-14GLCSL-FS-500-20 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
133013133013133013
13 1/813 1/413 1/813 1/813 1/413 1/813 1/813 1/413 1/8
16 1/223 7/818 7/816 1/223 7/818 7/816 1/223 7/818 7/8
24-
26 3/824-
26 3/824-
26 3/8
12 3/412 5/812 3/412 3/412 5/812 3/412 3/412 5/812 3/4
7 1/87 1/47 1/87 1/87 1/47 1/87 1/87 1/47 1/8
21 3/427
21 3/421 3/4
2721 3/421 3/4
2721 3/4
21’-4”21’-4”21’-4”21’-6”21’-6”21’-6”21’-6”21’-6”21’-6”
11’-9”12’-4 3/8”
11’-11 3/8”13’-9”
14’-4 3/8”13’-11 3/8”
15’-9”16’-4 3/8”
15’-11 3/8”
333444444
443443443
63’
10’10’12’12’14’14’
GLCS-FS-500-20 (S or AL)-63-10AL-FS-500-20-63-10
GLCS-FS-500-20 (S or AL)-63-12AL-FS-500-20-63-12
GLCS-FS-500-20 (S or AL)-63-14AL-FS-500-20-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
193619361936
13 1/813 1/413 1/813 1/413 1/813 1/4
16 1/223 7/816 1/223 7/816 1/223 7/8
24-
24-
24-
12 3/412 5/812 3/412 5/812 3/412 5/8
7 1/87 1/47 1/87 1/47 1/87 1/4
21 3/427
21 3/427
21 3/427
21’-4”21’-4”21’-6”21’-6”21’-6”21’-6”
11’-9”12’-4 3/8”
13’-9”14’-4 3/8”
15’-9”16’-4 3/8”
334444
444444
64’10’12’14’
GLCSLX-FS-500-20 (S or AL)-64-10GLCSLX-FS-500-20 (S or AL)-64-12GLCSLX-FS-500-20 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
13 1/813 1/813 1/8
20 7/820 7/820 7/8
28 3/828 3/828 3/8
12 3/412 3/412 3/4
7 1/87 1/87 1/8
272727
21’-4”21’-6”21’-6”
12’-1 3/8”14’-1 3/8”16’-1 3/8”
344
333
78’10’12’14’
GLCSL-FS-500-20 (S or AL)-78-10GLCSL-FS-500-20 (S or AL)-78-12GLCSL-FS-500-20 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
13 1/813 1/813 1/8
18 7/818 7/818 7/8
26 3/826 3/826 3/8
12 3/412 3/412 3/4
7 1/87 1/87 1/8
272727
21’-4”21’-6”21’-6”
11’-11 3/8”13’-11 3/8”15’-11 3/8”
344
444
83’
10’10’12’12’14’14’
GLCS-FS-500-20 (S or AL)-83-10AL-FS-500-20-83-10
GLCS-FS-500-20 (S or AL)-83-12AL-FS-500-20-83-12
GLCS-FS-500-20 (S or AL)-83-14AL-FS-500-20-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
13 1/813 1/413 1/813 1/413 1/813 1/4
16 1/223 7/816 1/223 7/816 1/223 7/8
24-
24-
24-
12 3/412 5/812 3/412 5/812 3/412 5/8
7 1/87 1/47 1/87 1/47 1/87 1/4
272727272727
21’-4”21’-4”21’-6”21’-6”21’-6”21’-6”
11’-9”12’-4 3/8”
13’-9”14’-4 3/8”
15’-9”16’-4 3/8”
334444
555555
94’10’12’14’
GLCSLX-FS-500-20 (S or AL)-94-10GLCSLX-FS-500-20 (S or AL)-94-12GLCSLX-FS-500-20 (S or AL)-94-14
SteelSteelSteel
30’30’30’
545454
13 1/813 1/813 1/8
20 7/820 7/820 7/8
28 3/828 3/828 3/8
12 3/412 3/412 3/4
7 1/87 1/87 1/8
272727
21’-4”21’-6”21’-6”
12’-1 3/8”14’-1 3/8”16’-1 3/8”
344
444
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-500-20 (S or AL)-103-10AL-FS-500-20-103-10
GLCSL-FS-500-20 (S or AL)-103-10GLCS-FS-500-20 (S or AL)-103-12
AL-FS-500-20-103-12GLCSL-FS-500-20 (S or AL)-103-12GLCS-FS-500-20 (S or AL)-103-14
AL-FS-500-20-103-14GLCSL-FS-500-20 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
13 1/813 1/413 1/813 1/813 1/413 1/813 1/813 1/413 1/8
16 1/223 7/818 7/816 1/223 7/818 7/816 1/223 7/818 7/8
24-
26 3/824-
26 3/824-
26 3/8
12 3/412 5/812 3/412 3/412 5/812 3/412 3/412 5/812 3/4
7 1/87 1/47 1/87 1/87 1/47 1/87 1/87 1/47 1/8
272727272727272727
21’-4”21’-4”21’-4”21’-6”21’-6”21’-6”21’-6”21’-6”21’-6”
11’-9”12’-4 3/8”
11’-11 3/8”13’-9”
14’-4 3/8”13’-11 3/8”
15’-9”16’-4 3/8”
15’-11 3/8”
333444444
665665665
124’10’12’14’
GLCSLX-FS-500-20 (S or AL)-124-10GLCSLX-FS-500-20 (S or AL)-124-12GLCSLX-FS-500-20 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
13 1/813 1/813 1/8
20 7/820 7/820 7/8
28 3/828 3/828 3/8
12 3/412 3/412 3/4
7 1/87 1/87 1/8
272727
21’-4”21’-6”21’-6”
12’-1 3/8”14’-1 3/8”16’-1 3/8”
344
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
500# CAPACITYFR
EE S
TAN
DIN
G W
OR
KST
ATIO
N C
RA
NES
13
FREE STA
ND
ING
WO
RK
STATION
CR
AN
ES
14
500# CAPACITYFREE STANDING WORK STATION BRIDGE CRANES
BRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
23’
23’
10’10’12’12’14’14’
GLCS-FS-500-23 (S or AL)-23-10AL-FS-500-23-23-10
GLCS-FS-500-23 (S or AL)-23-12AL-FS-500-23-23-12
GLCS-FS-500-23 (S or AL)-23-14AL-FS-500-23-23-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9139
139
13
13 1/813 1/413 1/813 1/413 1/813 1/4
16 1/223 7/816 1/223 7/816 1/223 7/8
24-
24-
24-
12 3/412 5/812 3/412 5/812 3/412 5/8
7 1/87 1/47 1/87 1/47 1/87 1/4
21 3/430 3/821 3/430 3/821 3/430 3/8
24’-4”24’-4”24’-6”24’-6”24’-6”24’-6”
11’-9”12’-4 3/8”
13’-9”14’-4 3/8”
15’-9”16’-4 3/8”
334444
222222
28’10’12’14’
GLCSL-FS-500-23 (S or AL)-28-10GLCSL-FS-500-23 (S or AL)-28-12GLCSL-FS-500-23 (S or AL)-28-14
SteelSteelSteel
25’25’25’
999
13 1/813 1/813 1/8
18 7/818 7/818 7/8
26 3/826 3/826 3/8
12 3/412 3/412 3/4
7 1/87 1/87 1/8
21 3/421 3/421 3/4
24’-4”24’-6”24’-6”
11’-11 3/8”13’-11 3/8”15’-11 3/8”
344
222
33’
10’10’12’12’14’14’
GLCS-FS-500-23 (S or AL)-33-10AL-FS-500-23-33-10
GLCS-FS-500-23 (S or AL)-33-12AL-FS-500-23-33-12
GLCS-FS-500-23 (S or AL)-33-14AL-FS-500-23-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9199
199
19
13 1/813 1/413 1/813 1/413 1/813 1/4
16 1/223 7/816 1/223 7/816 1/223 7/8
24-
24-
24-
12 3/412 5/812 3/412 5/812 3/412 5/8
7 1/87 1/47 1/87 1/47 1/87 1/4
21 3/430 3/821 3/430 3/821 3/430 3/8
24’-4”24’-4”24’-6”24’-6”24’-6”24’-6”
11’-9”12’-4 3/8”
13’-9”14’-4 3/8”
15’-9”16’-4 3/8”
334444
333333
34’10’12’14’
GLCSLX-FS-500-23 (S or AL)-34-10GLCSLX-FS-500-23 (S or AL)-34-12GLCSLX-FS-500-23 (S or AL)-34-14
SteelSteelSteel
30’30’30’
999
13 1/813 1/813 1/8
20 7/820 7/820 7/8
28 3/828 3/828 3/8
12 3/412 3/412 3/4
7 1/87 1/87 1/8
21 3/421 3/421 3/4
24’-4”24’-6”24’-6”
12’-1 3/8”14’-1 3/8”16’-1 3/8”
344
222
43’
10’10’12’12’14’14’
GLCS-FS-500-23 (S or AL)-43-10AL-FS-500-23-43-10
GLCS-FS-500-23 (S or AL)-43-12AL-FS-500-23-43-12
GLCS-FS-500-23 (S or AL)-43-14AL-FS-500-23-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
132613261326
13 1/813 1/413 1/813 1/413 1/813 1/4
16 1/223 7/816 1/223 7/816 1/223 7/8
24-
24-
24-
12 3/412 5/812 3/412 5/812 3/412 5/8
7 1/87 1/47 1/87 1/47 1/87 1/4
21 3/430 3/821 3/430 3/821 3/430 3/8
24’-4”24’-4”24’-6”24’-6”24’-6”24’-6”
11’-9”12’-4 3/8”
13’-9”14’-4 3/8”
15’-9”16’-4 3/8”
334444
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-500-23 (S or AL)-53-10AL-FS-500-23-53-10
GLCSL-FS-500-23 (S or AL)-53-10GLCS-FS-500-23 (S or AL)-53-12
AL-FS-500-23-53-12GLCSL-FS-500-23 (S or AL)-53-12GLCS-FS-500-23 (S or AL)-53-14
AL-FS-500-23-53-14GLCSL-FS-500-23 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
133013133013133013
13 1/813 1/413 1/813 1/813 1/413 1/813 1/813 1/413 1/8
16 1/223 7/818 7/816 1/223 7/818 7/816 1/223 7/818 7/8
24-
26 3/824-
26 3/824-
26 3/8
12 3/412 5/812 3/412 3/412 5/812 3/412 3/412 5/812 3/4
7 1/87 1/47 1/87 1/87 1/47 1/87 1/87 1/47 1/8
21 3/430 3/821 3/421 3/430 3/821 3/421 3/430 3/821 3/4
24’-4”24’-4”24’-4”24’-6”24’-6”24’-6”24’-6”24’-6”24’-6”
11’-9”12’-4 3/8”
11’-11 3/8”13’-9”
14’-4 3/8”13’-11 3/8”
15’-9”16’-4 3/8”
15’-11 3/8”
333444444
443443443
63’
10’10’12’12’14’14’
GLCS-FS-500-23 (S or AL)-63-10AL-FS-500-23-63-10
GLCS-FS-500-23 (S or AL)-63-12AL-FS-500-23-63-12
GLCS-FS-500-23 (S or AL)-63-14AL-FS-500-23-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
193619361936
13 1/813 1/413 1/813 1/413 1/813 1/4
16 1/223 7/816 1/223 7/816 1/223 7/8
24-
24-
24-
12 3/412 5/812 3/412 5/812 3/412 5/8
7 1/87 1/47 1/87 1/47 1/87 1/4
21 3/430 3/821 3/430 3/821 3/430 3/8
24’-4”24’-4”24’-6”24’-6”24’-6”24’-6”
11’-9”12’-4 3/8”
13’-9”14’-4 3/8”
15’-9”16’-4 3/8”
334444
444444
64’10’12’14’
GLCSLX-FS-500-23 (S or AL)-64-10GLCSLX-FS-500-23 (S or AL)-64-12GLCSLX-FS-500-23 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
13 1/813 1/813 1/8
20 7/820 7/820 7/8
28 3/828 3/828 3/8
12 3/412 3/412 3/4
7 1/87 1/87 1/8
30 3/830 3/830 3/8
24’-4”24’-6”24’-6”
12’-1 3/8”14’-1 3/8”16’-1 3/8”
344
333
78’10’12’14’
GLCSL-FS-500-23 (S or AL)-78-10GLCSL-FS-500-23 (S or AL)-78-12GLCSL-FS-500-23 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
13 1/813 1/813 1/8
18 7/818 7/818 7/8
26 3/826 3/826 3/8
12 3/412 3/412 3/4
7 1/87 1/87 1/8
30 3/830 3/830 3/8
24’-4”24’-6”24’-6”
11’-11 3/8”13’-11 3/8”15’-11 3/8”
344
444
83’
10’10’12’12’14’14’
GLCS-FS-500-23 (S or AL)-83-10AL-FS-500-23-83-10
GLCS-FS-500-23 (S or AL)-83-12AL-FS-500-23-83-12
GLCS-FS-500-23 (S or AL)-83-14AL-FS-500-23-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
13 1/813 1/413 1/813 1/413 1/813 1/4
16 1/223 7/816 1/223 7/816 1/223 7/8
24-
24-
24-
12 3/412 5/812 3/412 5/812 3/412 5/8
7 1/87 1/47 1/87 1/47 1/87 1/4
30 3/830 3/830 3/830 3/830 3/830 3/8
24’-4”24’-4”24’-6”24’-6”24’-6”24’-6”
11’-9”12’-4 3/8”
13’-9”14’-4 3/8”
15’-9”16’-4 3/8”
334444
555555
94’10’12’14’
GLCSLX-FS-500-23 (S or AL)-94-10GLCSLX-FS-500-23 (S or AL)-94-12GLCSLX-FS-500-23 (S or AL)-94-14
SteelSteelSteel
30’30’30’
545454
13 1/813 1/813 1/8
20 7/820 7/820 7/8
28 3/828 3/828 3/8
12 3/412 3/412 3/4
7 1/87 1/87 1/8
30 3/830 3/830 3/8
24’-4”24’-6”24’-6”
12’-1 3/8”14’-1 3/8”16’-1 3/8”
344
444
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-500-23 (S or AL)-103-10AL-FS-500-23-103-10
GLCSL-FS-500-23 (S or AL)-103-10GLCS-FS-500-23 (S or AL)-103-12
AL-FS-500-23-103-12GLCSL-FS-500-23 (S or AL)-103-12GLCS-FS-500-23 (S or AL)-103-14
AL-FS-500-23-103-14GLCSL-FS-500-23 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
13 1/813 1/413 1/813 1/813 1/413 1/813 1/813 1/413 1/8
16 1/223 7/818 7/816 1/223 7/818 7/816 1/223 7/818 7/8
24-
26 3/824-
26 3/824-
26 3/8
12 3/412 5/812 3/412 3/412 5/812 3/412 3/412 5/812 3/4
7 1/87 1/47 1/87 1/87 1/47 1/87 1/87 1/47 1/8
30 3/830 3/830 3/830 3/830 3/830 3/830 3/830 3/830 3/8
24’-4”24’-4”24’-4”24’-6”24’-6”24’-6”24’-6”24’-6”24’-6”
11’-9”12’-4 3/8”
11’-11 3/8”13’-9”
14’-4 3/8”13’-11 3/8”
15’-9”16’-4 3/8”
15’-11 3/8”
333444444
665665665
124’10’12’14’
GLCSLX-FS-500-23 (S or AL)-124-10GLCSLX-FS-500-23 (S or AL)-124-12GLCSLX-FS-500-23 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
13 1/813 1/813 1/8
20 7/820 7/820 7/8
28 3/828 3/828 3/8
12 3/412 3/412 3/4
7 1/87 1/87 1/8
30 3/830 3/830 3/8
24’-4”24’-6”24’-6”
12’-1 3/8”14’-1 3/8”16’-1 3/8”
344
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
FREE STANDING WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
28’
23’
10’10’12’12’14’14’
GLCS-FS-500-28 (S or AL)-23-10AL-FS-500-28-23-10
GLCS-FS-500-28 (S or AL)-23-12AL-FS-500-28-23-12
GLCS-FS-500-28 (S or AL)-23-14AL-FS-500-28-23-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9139
139
13
23 1/423 3/823 1/423 3/823 1/423 3/8
18 3/822 5/818 3/822 5/818 3/822 5/8
22 5/8-
22 5/8-
22 5/8-
15 1/813 1/815 1/813 1/815 1/813 1/8
7 1/87 7/87 1/87 7/87 1/87 7/8
31 1/437 1/831 1/437 1/831 1/437 1/8
29’-4”29’-4”29’-6”29’-6”29’-6”29’-6”
11’-11 7/8”12’-4 1/8”
13’-11 7/8”14’-4 1/8”
15’-11 7/8”16’-4 1/8”
334444
222222
28’10’12’14’
GLCSL-FS-500-28 (S or AL)-28-10GLCSL-FS-500-28 (S or AL)-28-12GLCSL-FS-500-28 (S or AL)-28-14
SteelSteelSteel
25’25’25’
999
23 1/423 1/423 1/4
20 3/420 3/420 3/4
252525
15 1/815 1/815 1/8
7 1/87 1/87 1/8
31 1/431 1/431 1/4
29’-4”29’-6”29’-6”
12’-2 1/4”14’-2 1/4”16’-2 1/4”
344
222
33’
10’10’12’12’14’14’
GLCS-FS-500-28 (S or AL)-33-10AL-FS-500-28-33-10
GLCS-FS-500-28 (S or AL)-33-12AL-FS-500-28-33-12
GLCS-FS-500-28 (S or AL)-33-14AL-FS-500-28-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9199
199
19
23 1/423 3/823 1/423 3/823 1/423 3/8
18 3/822 5/818 3/822 5/818 3/822 5/8
22 5/8-
22 5/8-
22 5/8-
15 1/813 1/815 1/813 1/815 1/813 1/8
7 1/87 7/87 1/87 7/87 1/87 7/8
31 1/437 1/831 1/437 1/831 1/437 1/8
29’-4”29’-4”29’-6”29’-6”29’-6”29’-6”
11’-11 7/8”12’-4 1/8”
13’-11 7/8”14’-4 1/8”
15’-11 7/8”16’-4 1/8”
334444
333333
34’10’12’14’
GLCSLX-FS-500-28 (S or AL)-34-10GLCSLX-FS-500-28 (S or AL)-34-12GLCSLX-FS-500-28 (S or AL)-34-14
SteelSteelSteel
30’30’30’
999
23 1/423 1/423 1/4
22 3/422 3/422 3/4
272727
15 1/815 1/815 1/8
7 1/87 1/87 1/8
31 1/431 1/431 1/4
29’-4”29’-6”29’-6”
12’-4 1/4”14’-4 1/4”16’-4 1/4”
344
222
43’
10’10’12’12’14’14’
GLCS-FS-500-28 (S or AL)-43-10AL-FS-500-28-43-10
GLCS-FS-500-28 (S or AL)-43-12AL-FS-500-28-43-12
GLCS-FS-500-28 (S or AL)-43-14AL-FS-500-28-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
132613261326
23 1/423 3/823 1/423 3/823 1/423 3/8
18 3/822 5/818 3/822 5/818 3/822 5/8
22 5/8-
22 5/8-
22 5/8-
15 1/813 1/815 1/813 1/815 1/813 1/8
7 1/87 7/87 1/87 7/87 1/87 7/8
31 1/437 1/831 1/437 1/831 1/437 1/8
29’-4”29’-4”29’-6”29’-6”29’-6”29’-6”
11’-11 7/8”12’-4 1/8”
13’-11 7/8”14’-4 1/8”
15’-11 7/8”16’-4 1/8”
334444
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-500-28 (S or AL)-53-10AL-FS-500-28-53-10
GLCSL-FS-500-28 (S or AL)-53-10GLCS-FS-500-28 (S or AL)-53-12
AL-FS-500-28-53-12GLCSL-FS-500-28 (S or AL)-53-12GLCS-FS-500-28 (S or AL)-53-14
AL-FS-500-28-53-14GLCSL-FS-500-28 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
133013133013133013
23 1/423 3/823 1/423 1/423 3/823 1/423 1/423 3/823 1/4
18 3/822 5/820 3/418 3/822 5/820 3/418 3/822 5/820 3/4
22 5/8-
2522 5/8
-25
22 5/8-
25
15 1/813 1/815 1/815 1/813 1/815 1/815 1/813 1/815 1/8
7 1/87 7/87 1/87 1/87 7/87 1/87 1/87 7/87 1/8
31 1/437 1/831 1/431 1/437 1/831 1/431 1/437 1/831 1/4
29’-4”29’-4”29’-4”29’-6”29’-6”29’-6”29’-6”29’-6”29’-6”
11’-11 7/8”12’-4 1/8”12’-2 1/4”
13’-11 7/8”14’-4 1/8”14’-2 1/4”
15’-11 7/8”16’-4 1/8”16’-2 1/4”
333444444
443443443
63’
10’10’12’12’14’14’
GLCS-FS-500-28 (S or AL)-63-10AL-FS-500-28-63-10
GLCS-FS-500-28 (S or AL)-63-12AL-FS-500-28-63-12
GLCS-FS-500-28 (S or AL)-63-14AL-FS-500-28-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
193619361936
23 1/423 3/823 1/423 3/823 1/423 3/8
18 3/822 5/818 3/822 5/818 3/822 5/8
22 5/8-
22 5/8-
22 5/8-
15 1/813 1/815 1/813 1/815 1/813 1/8
7 1/87 7/87 1/87 7/87 1/87 7/8
31 1/437 1/831 1/437 1/831 1/437 1/8
29’-4”29’-4”29’-6”29’-6”29’-6”29’-6”
11’-11 7/8”12’-4 1/8”
13’-11 7/8”14’-4 1/8”
15’-11 7/8”16’-4 1/8”
334444
444444
64’10’12’14’
GLCSLX-FS-500-28 (S or AL)-64-10GLCSLX-FS-500-28 (S or AL)-64-12GLCSLX-FS-500-28 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
23 1/423 1/423 1/4
22 3/422 3/422 3/4
272727
15 1/815 1/815 1/8
7 1/87 1/87 1/8
37 1/837 1/837 1/8
29’-4”29’-6”29’-6”
12’-4 1/4”14’-4 1/4”16’-4 1/4”
344
333
78’10’12’14’
GLCSL-FS-500-28 (S or AL)-78-10GLCSL-FS-500-28 (S or AL)-78-12GLCSL-FS-500-28 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
23 1/423 1/423 1/4
20 3/420 3/420 3/4
252525
15 1/815 1/815 1/8
7 1/87 1/87 1/8
37 1/837 1/837 1/8
29’-4”29’-6”29’-6”
12’-2 1/4”14’-2 1/4”16’-2 1/4”
344
444
83’
10’10’12’12’14’14’
GLCS-FS-500-28 (S or AL)-83-10AL-FS-500-28-83-10
GLCS-FS-500-28 (S or AL)-83-12AL-FS-500-28-83-12
GLCS-FS-500-28 (S or AL)-83-14AL-FS-500-28-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
23 1/423 3/823 1/423 3/823 1/423 3/8
18 3/822 5/818 3/822 5/818 3/822 5/8
22 5/8-
22 5/8-
22 5/8-
15 1/813 1/815 1/813 1/815 1/813 1/8
7 1/87 7/87 1/87 7/87 1/87 7/8
37 1/837 1/837 1/837 1/837 1/837 1/8
29’-4”29’-4”29’-6”29’-6”29’-6”29’-6”
11’-11 7/8”12’-4 1/8”
13’-11 7/8”14’-4 1/8”
15’-11 7/8”16’-4 1/8”
334444
555555
94’10’12’14’
GLCSLX-FS-500-28 (S or AL)-94-10GLCSLX-FS-500-28 (S or AL)-94-12GLCSLX-FS-500-28 (S or AL)-94-14
SteelSteelSteel
30’30’30’
545454
23 1/423 1/423 1/4
22 3/422 3/422 3/4
272727
15 1/815 1/815 1/8
7 1/87 1/87 1/8
37 1/837 1/837 1/8
29’-4”29’-6”29’-6”
12’-4 1/4”14’-4 1/4”16’-4 1/4”
344
444
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-500-28 (S or AL)-103-10AL-FS-500-28-103-10
GLCSL-FS-500-28 (S or AL)-103-10GLCS-FS-500-28 (S or AL)-103-12
AL-FS-500-28-103-12GLCSL-FS-500-28 (S or AL)-103-12GLCS-FS-500-28 (S or AL)-103-14
AL-FS-500-28-103-14GLCSL-FS-500-28 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
23 1/423 3/823 1/423 1/423 3/823 1/423 1/423 3/823 1/4
18 3/822 5/820 3/418 3/822 5/820 3/418 3/822 5/820 3/4
22 5/8-
2522 5/8
-25
22 5/8-
25
15 1/813 1/815 1/815 1/813 1/815 1/815 1/813 1/815 1/8
7 1/87 7/87 1/87 1/87 7/87 1/87 1/87 7/87 1/8
37 1/837 1/837 1/837 1/837 1/837 1/837 1/837 1/837 1/8
29’-4”29’-4”29’-4”29’-6”29’-6”29’-6”29’-6”29’-6”29’-6”
11’-11 7/8”12’-4 1/8”12’-2 1/4”
13’-11 7/8”14’-4 1/8”14’-2 1/4”
15’-11 7/8”16’-4 1/8”16’-2 1/4”
333444444
665665665
124’10’12’14’
GLCSLX-FS-500-28 (S or AL)-124-10GLCSLX-FS-500-28 (S or AL)-124-12GLCSLX-FS-500-28 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
23 1/423 1/423 1/4
22 3/422 3/422 3/4
272727
15 1/815 1/815 1/8
7 1/87 1/87 1/8
37 1/837 1/837 1/8
29’-4”29’-6”29’-6”
12’-4 1/4”14’-4 1/4”16’-4 1/4”
344
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
500# CAPACITYFR
EE S
TAN
DIN
G W
OR
KST
ATIO
N C
RA
NES
15
FREE STA
ND
ING
WO
RK
STATION
CR
AN
ES
16
500# CAPACITYFREE STANDING WORK STATION BRIDGE CRANES
BRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
34’
28’10’12’14’
GLCSL-FS-500-34 (S or AL)-28-10GLCSL-FS-500-34 (S or AL)-28-12GLCSL-FS-500-34 (S or AL)-28-14
SteelSteelSteel
25’25’25’
999
23 1/423 1/423 1/4
20 3/420 3/420 3/4
252525
17 1/817 1/817 1/8
7 1/87 1/87 1/8
20 1/220 1/220 1/2
35’-6”35’-6”35’-6”
12’-3 1/4”14’-3 1/4”16’-3 1/4”
444
222
33’
10’10’12’12’14’14’
GLCS-FS-500-34 (S or AL)-33-10AL-FS-500-34-33-10
GLCS-FS-500-34 (S or AL)-33-12AL-FS-500-34-33-12
GLCS-FS-500-34 (S or AL)-33-14AL-FS-500-34-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9199
199
19
23 1/423 3/823 1/423 3/823 1/423 3/8
20 3/822 5/820 3/822 5/820 3/822 5/8
22 5/8-
22 5/8-
22 5/8-
17 1/815 1/417 1/815 1/417 1/815 1/4
7 1/87 7/87 1/87 7/87 1/87 7/8
20 1/243 7/820 1/243 7/820 1/243 7/8
35’-6”35’-6”35’-6”35’-6”35’-6”35’-6”
12’-2 7/8”12’-5 1/8”14’-2 7/8”14’-5 1/8”16’-2 7/8”16’-5 1/8”
444444
333333
34’10’12’14’
GLCSLX-FS-500-34 (S or AL)-34-10GLCSLX-FS-500-34 (S or AL)-34-12GLCSLX-FS-500-34 (S or AL)-34-14
SteelSteelSteel
30’30’30’
999
23 1/423 1/423 1/4
22 3/422 3/422 3/4
272727
17 1/817 1/817 1/8
7 1/87 1/87 1/8
20 1/220 1/220 1/2
35’-6”35’-6”35’-6”
12’-5 1/4”14’-5 1/4”16’-5 1/4”
444
222
43’
10’10’12’12’14’14’
GLCS-FS-500-34 (S or AL)-43-10AL-FS-500-34-43-10
GLCS-FS-500-34 (S or AL)-43-12AL-FS-500-34-43-12
GLCS-FS-500-34 (S or AL)-43-14AL-FS-500-34-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
132613261326
23 1/423 3/823 1/423 3/823 1/423 3/8
20 3/822 5/820 3/822 5/820 3/822 5/8
22 5/8-
22 5/8-
22 5/8-
17 1/815 1/417 1/815 1/417 1/815 1/4
7 1/87 7/87 1/87 7/87 1/87 7/8
20 1/243 7/820 1/243 7/820 1/243 7/8
35’-6”35’-6”35’-6”35’-6”35’-6”35’-6”
12’-2 7/8”12’-5 1/8”14’-2 7/8”14’-5 1/8”16’-2 7/8”16’-5 1/8”
444444
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-500-34 (S or AL)-53-10AL-FS-500-34-53-10
GLCSL-FS-500-34 (S or AL)-53-10GLCS-FS-500-34 (S or AL)-53-12
AL-FS-500-34-53-12GLCSL-FS-500-34 (S or AL)-53-12GLCS-FS-500-34 (S or AL)-53-14
AL-FS-500-34-53-14GLCSL-FS-500-34 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
133013133013133013
23 1/423 3/823 1/423 1/423 3/823 1/423 1/423 3/823 1/4
20 3/822 5/820 3/420 3/822 5/820 3/420 3/822 5/820 3/4
22 5/8-
2522 5/8
-25
22 5/8-
25
17 1/815 1/417 1/817 1/815 1/417 1/817 1/815 1/417 1/8
7 1/87 7/87 1/87 1/87 7/87 1/87 1/87 7/87 1/8
20 1/243 7/820 1/220 1/243 7/820 1/220 1/243 7/820 1/2
35’-6”35’-6”35’-6”35’-6”35’-6”35’-6”35’-6”35’-6”35’-6”
12’-2 7/8”12’-5 1/8”12’-3 1/4”14’-2 7/8”14’-5 1/8”14’-3 1/4”16’-2 7/8”16’-5 1/8”16’-3 1/4”
444444444
443443443
63’
10’10’12’12’14’14’
GLCS-FS-500-34 (S or AL)-63-10AL-FS-500-34-63-10
GLCS-FS-500-34 (S or AL)-63-12AL-FS-500-34-63-12
GLCS-FS-500-34 (S or AL)-63-14AL-FS-500-34-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
193619361936
23 1/423 3/823 1/423 3/823 1/423 3/8
20 3/822 5/820 3/822 5/820 3/822 5/8
22 5/8-
22 5/8-
22 5/8-
17 1/815 1/417 1/815 1/417 1/815 1/4
7 1/87 7/87 1/87 7/87 1/87 7/8
20 1/243 7/820 1/243 7/820 1/243 7/8
35’-6”35’-6”35’-6”35’-6”35’-6”35’-6”
12’-2 7/8”12’-5 1/8”14’-2 7/8”14’-5 1/8”16’-2 7/8”16’-5 1/8”
444444
444444
64’10’12’14’
GLCSLX-FS-500-34 (S or AL)-64-10GLCSLX-FS-500-34 (S or AL)-64-12GLCSLX-FS-500-34 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
23 1/423 1/423 1/4
22 3/422 3/422 3/4
272727
17 1/817 1/817 1/8
7 1/87 1/87 1/8
43 7/843 7/843 7/8
35’-6”35’-6”35’-6”
12’-5 1/4”14’-5 1/4”16’-5 1/4”
444
333
78’10’12’14’
GLCSL-FS-500-34 (S or AL)-78-10GLCSL-FS-500-34 (S or AL)-78-12GLCSL-FS-500-34 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
23 1/423 1/423 1/4
20 3/420 3/420 3/4
252525
17 1/817 1/817 1/8
7 1/87 1/87 1/8
43 7/843 7/843 7/8
35’-6”35’-6”35’-6”
12’-3 1/4”14’-3 1/4”16’-3 1/4”
444
444
83’
10’10’12’12’14’14’
GLCS-FS-500-34 (S or AL)-83-10AL-FS-500-34-83-10
GLCS-FS-500-34 (S or AL)-83-12AL-FS-500-34-83-12
GLCS-FS-500-34 (S or AL)-83-14AL-FS-500-34-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
23 1/423 3/823 1/423 3/823 1/423 3/8
20 3/822 5/820 3/822 5/820 3/822 5/8
22 5/8-
22 5/8-
22 5/8-
17 1/815 1/417 1/815 1/417 1/815 1/4
7 1/87 7/87 1/87 7/87 1/87 7/8
43 7/843 7/843 7/843 7/843 7/843 7/8
35’-6”35’-6”35’-6”35’-6”35’-6”35’-6”
12’-2 7/8”12’-5 1/8”14’-2 7/8”14’-5 1/8”16’-2 7/8”16’-5 1/8”
444444
555555
94’10’12’14’
GLCSLX-FS-500-34 (S or AL)-94-10GLCSLX-FS-500-34 (S or AL)-94-12GLCSLX-FS-500-34 (S or AL)-94-14
SteelSteelSteel
30’30’30’
545454
23 1/423 1/423 1/4
22 3/422 3/422 3/4
272727
17 1/817 1/817 1/8
7 1/87 1/87 1/8
43 7/843 7/843 7/8
35’-6”35’-6”35’-6”
12’-5 1/4”14’-5 1/4”16’-5 1/4”
444
444
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-500-34 (S or AL)-103-10AL-FS-500-34-103-10
GLCSL-FS-500-34 (S or AL)-103-10GLCS-FS-500-34 (S or AL)-103-12
AL-FS-500-34-103-12GLCSL-FS-500-34 (S or AL)-103-12GLCS-FS-500-34 (S or AL)-103-14
AL-FS-500-34-103-14GLCSL-FS-500-34 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
23 1/423 3/823 1/423 1/423 3/823 1/423 1/423 3/823 1/4
20 3/822 5/820 3/420 3/822 5/820 3/420 3/822 5/820 3/4
22 5/8-
2522 5/8
-25
22 5/8-
25
17 1/815 1/417 1/817 1/815 1/417 1/817 1/815 1/417 1/8
7 1/87 7/87 1/87 1/87 7/87 1/87 1/87 7/87 1/8
43 7/843 7/843 7/843 7/843 7/843 7/843 7/843 7/843 7/8
35’-6”35’-6”35’-6”35’-6”35’-6”35’-6”35’-6”35’-6”35’-6”
12’-2 7/8”12’-5 1/8”12’-3 1/4”14’-2 7/8”14’-5 1/8”14’-3 1/4”16’-2 7/8”16’-5 1/8”16’-3 1/4”
444444444
665665665
124’10’12’14’
GLCSLX-FS-500-34 (S or AL)-124-10GLCSLX-FS-500-34 (S or AL)-124-12GLCSLX-FS-500-34 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
23 1/423 1/423 1/4
22 3/422 3/422 3/4
272727
17 1/817 1/817 1/8
7 1/87 1/87 1/8
43 7/843 7/843 7/8
35’-6”35’-6”35’-6”
12’-5 1/4”14’-5 1/4”16’-5 1/4”
444
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
FREE STANDING WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
10’
11’-6”10’12’14’
GLCS-FS-1000-10 (S or AL)-11.5-10GLCS-FS-1000-10 (S or AL)-11.5-12GLCS-FS-1000-10 (S or AL)-11.5-14
SteelSteelSteel
20’20’20’
999
151515
18 1/818 1/818 1/8
22 1/822 1/822 1/8
7 5/87 5/87 5/8
7 7/87 7/87 7/8
13 3/813 3/813 3/8
11’-6”11’-6”11’-8”
11’-10 5/8”13’-10 5/8”15’-10 5/8”
445
222
23’
10’10’12’12’14’14’
GLCS-FS-1000-10 (S or AL)-23-10AL-FS-1000-10-23-10
GLCS-FS-1000-10 (S or AL)-23-12AL-FS-1000-10-23-12
GLCS-FS-1000-10 (S or AL)-23-14AL-FS-1000-10-23-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9139
139
13
151515151515
18 1/822 1/818 1/822 1/818 1/822 1/8
22 1/8-
22 1/8-
22 1/8-
7 5/813 1/87 5/8
13 1/87 5/8
13 1/8
7 7/87 7/87 7/87 7/87 7/87 7/8
13 3/817 1/213 3/817 1/213 3/817 1/2
11’-6”11’-6”11’-6”11’-6”11’-8”11’-8”
11’-10 5/8”12’-2 5/8”
13’-10 5/8”14’-2 5/8”
15’-10 5/8”16’-2 5/8”
444455
222222
28’10’12’14’
GLCSL-FS-1000-10 (S or AL)-28-10GLCSL-FS-1000-10 (S or AL)-28-12GLCSL-FS-1000-10 (S or AL)-28-14
SteelSteelSteel
25’25’25’
131313
151515
212121
252525
7 5/87 5/87 5/8
7 7/87 7/87 7/8
13 3/813 3/813 3/8
11’-6”11’-6”11’-8”
12’-1 1/2”14’-1 1/2”16’-1 1/2”
445
222
33’
10’10’12’12’14’14’
GLCS-FS-1000-10 (S or AL)-33-10AL-FS-1000-10-33-10
GLCS-FS-1000-10 (S or AL)-33-12AL-FS-1000-10-33-12
GLCS-FS-1000-10 (S or AL)-33-14AL-FS-1000-10-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
131913191319
151515151515
18 1/822 1/818 1/822 1/818 1/822 1/8
22 1/8-
22 1/8-
22 1/8-
7 5/813 1/87 5/8
13 1/87 5/8
13 1/8
7 7/87 7/87 7/87 7/87 7/87 7/8
13 3/817 1/213 3/817 1/213 3/817 1/2
11’-6”11’-6”11’-6”11’-6”11’-8”11’-8”
11’-10 5/8”12’-2 5/8”
13’-10 5/8”14’-2 5/8”
15’-10 5/8”16’-2 5/8”
444455
333333
34’10’12’14’
GLCSLX-FS-1000-10 (S or AL)-34-10GLCSLX-FS-1000-10 (S or AL)-34-12GLCSLX-FS-1000-10 (S or AL)-34-14
SteelSteelSteel
30’30’30’
131313
151515
24 1/824 1/824 1/8
28 1/828 1/828 1/8
7 5/87 5/87 5/8
7 7/87 7/87 7/8
13 3/813 3/813 3/8
11’-6”11’-6”11’-8”
12’-4 5/8”14’-4 5/8”16’-4 5/8”
445
222
43’
10’10’12’12’14’14’
GLCS-FS-1000-10 (S or AL)-43-10AL-FS-1000-10-43-10
GLCS-FS-1000-10 (S or AL)-43-12AL-FS-1000-10-43-12
GLCS-FS-1000-10 (S or AL)-43-14AL-FS-1000-10-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
192619261926
151515151515
18 1/822 1/818 1/822 1/818 1/822 1/8
22 1/8-
22 1/8-
22 1/8-
7 5/813 1/87 5/8
13 1/87 5/8
13 1/8
7 7/87 7/87 7/87 7/87 7/87 7/8
13 3/817 1/213 3/817 1/213 3/817 1/2
11’-6”11’-6”11’-6”11’-6”11’-8”11’-8”
11’-10 5/8”12’-2 5/8”
13’-10 5/8”14’-2 5/8”
15’-10 5/8”16’-2 5/8”
444455
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-1000-10 (S or AL)-53-10AL-FS-1000-10-53-10
GLCSL-FS-1000-10 (S or AL)-53-10GLCS-FS-1000-10 (S or AL)-53-12
AL-FS-1000-10-53-12GLCSL-FS-1000-10 (S or AL)-53-12GLCS-FS-1000-10 (S or AL)-53-14
AL-FS-1000-10-53-14GLCSL-FS-1000-10 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
193019193019193019
151515151515151515
18 1/822 1/8
2118 1/822 1/8
2118 1/822 1/8
21
22 1/8-
2522 1/8
-25
22 1/8-
25
7 5/813 1/87 5/87 5/8
13 1/87 5/87 5/8
13 1/87 5/8
7 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/8
13 3/817 1/213 3/813 3/817 1/213 3/813 3/817 1/213 3/8
11’-6”11’-6”11’-6”11’-6”11’-6”11’-6”11’-8”11’-8”11’-8”
11’-10 5/8”12’-2 5/8”12’-1 1/2”
13’-10 5/8”14’-2 5/8”14’-1 1/2”
15’-10 5/8”16’-2 5/8”16’-1 1/2”
444444555
443443443
63’
10’10’12’12’14’14’
GLCS-FS-1000-10 (S or AL)-63-10AL-FS-1000-10-63-10
GLCS-FS-1000-10 (S or AL)-63-12AL-FS-1000-10-63-12
GLCS-FS-1000-10 (S or AL)-63-14AL-FS-1000-10-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
263626362636
151515151515
18 1/822 1/818 1/822 1/818 1/822 1/8
22 1/8-
22 1/8-
22 1/8-
7 5/813 1/87 5/8
13 1/87 5/8
13 1/8
7 7/87 7/87 7/87 7/87 7/87 7/8
13 3/817 1/213 3/817 1/213 3/817 1/2
11’-6”11’-6”11’-6”11’-6”11’-8”11’-8”
11’-10 5/8”12’-2 5/8”
13’-10 5/8”14’-2 5/8”
15’-10 5/8”16’-2 5/8”
444455
444444
64’10’12’14’
GLCSLX-FS-1000-10 (S or AL)-64-10GLCSLX-FS-1000-10 (S or AL)-64-12GLCSLX-FS-1000-10 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
151515
24 1/824 1/824 1/8
28 1/828 1/828 1/8
7 5/87 5/87 5/8
7 7/87 7/87 7/8
23 3/823 3/823 3/8
11’-6”11’-6”11’-8”
12’-4 5/8”14’-4 5/8”16’-4 5/8”
445
333
78’10’12’14’
GLCSL-FS-1000-10 (S or AL)-78-10GLCSL-FS-1000-10 (S or AL)-78-12GLCSL-FS-1000-10 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
151515
212121
252525
7 5/87 5/87 5/8
7 7/87 7/87 7/8
23 3/823 3/823 3/8
11’-6”11’-6”11’-8”
12’-1 1/2”14’-1 1/2”16’-1 1/2”
445
444
83’
10’10’12’12’14’14’
GLCS-FS-1000-10 (S or AL)-83-10AL-FS-1000-10-83-10
GLCS-FS-1000-10 (S or AL)-83-12AL-FS-1000-10-83-12
GLCS-FS-1000-10 (S or AL)-83-14AL-FS-1000-10-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
151515151515
18 1/822 1/818 1/822 1/818 1/822 1/8
22 1/8-
22 1/8-
22 1/8-
7 5/813 1/87 5/8
13 1/87 5/8
13 1/8
7 7/87 7/87 7/87 7/87 7/87 7/8
23 3/817 1/223 3/817 1/223 3/817 1/2
11’-6”11’-6”11’-6”11’-6”11’-8”11’-8”
11’-10 5/8”12’-2 5/8”
13’-10 5/8”14’-2 5/8”
15’-10 5/8”16’-2 5/8”
444455
555555
94’10’12’14’
GLCSLX-FS-1000-10 (S or AL)-94-10GLCSLX-FS-1000-10 (S or AL)-94-12GLCSLX-FS-1000-10 (S or AL)-94-14
SteelSteelSteel
30’30’30’
545454
151515
24 1/824 1/824 1/8
28 1/828 1/828 1/8
7 5/87 5/87 5/8
7 7/87 7/87 7/8
23 3/823 3/823 3/8
11’-6”11’-6”11’-8”
12’-4 5/8”14’-4 5/8”16’-4 5/8”
445
444
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-1000-10 (S or AL)-103-10AL-FS-1000-10-103-10
GLCSL-FS-1000-10 (S or AL)-103-10GLCS-FS-1000-10 (S or AL)-103-12
AL-FS-1000-10-103-12GLCSL-FS-1000-10 (S or AL)-103-12GLCS-FS-1000-10 (S or AL)-103-14
AL-FS-1000-10-103-14GLCSL-FS-1000-10 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
151515151515151515
18 1/822 1/8
2118 1/822 1/8
2118 1/822 1/8
21
22 1/8-
2522 1/8
-25
22 1/8-
25
7 5/813 1/87 5/87 5/8
13 1/87 5/87 5/8
13 1/87 5/8
7 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/8
23 3/817 1/223 3/823 3/817 1/223 3/823 3/817 1/223 3/8
11’-6”11’-6”11’-6”11’-6”11’-6”11’-6”11’-8”11’-8”11’-8”
11’-10 5/8”12’-2 5/8”12’-1 1/2”
13’-10 5/8”14’-2 5/8”14’-1 1/2”
15’-10 5/8”16’-2 5/8”16’-1 1/2”
444444555
665665665
124’10’12’14’
GLCSLX-FS-1000-10 (S or AL)-124-10GLCSLX-FS-1000-10 (S or AL)-124-12GLCSLX-FS-1000-10 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
151515
24 1/824 1/824 1/8
28 1/828 1/828 1/8
7 5/87 5/87 5/8
7 7/87 7/87 7/8
23 3/823 3/823 3/8
11’-6”11’-6”11’-8”
12’-4 5/8”14’-4 5/8”16’-4 5/8”
445
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
1000# CAPACITYFR
EE S
TAN
DIN
G W
OR
KST
ATIO
N C
RA
NES
17
18
1000# CAPACITYFREE STANDING WORK STATION BRIDGE CRANES
BRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
15’
23’
10’10’12’12’14’14’
GLCS-FS-1000-15 (S or AL)-23-10AL-FS-1000-15-23-10
GLCS-FS-1000-15 (S or AL)-23-12AL-FS-1000-15-23-12
GLCS-FS-1000-15 (S or AL)-23-14AL-FS-1000-15-23-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9139
139
13
151515151515
18 1/822 1/818 1/822 1/818 1/822 1/8
22 1/8-
22 1/8-
22 1/8-
14 1/813 1/814 1/813 1/814 1/813 1/8
7 7/87 7/87 7/87 7/87 7/87 7/8
23 3/824 1/423 3/824 1/423 3/824 1/4
16’-6”16’-6”16’-6”16’-6”16’-8”16’-8”
11’-10 5/8”12’-2 5/8”
13’-10 5/8”14’-2 5/8”
15’-10 5/8”16’-2 5/8”
444455
222222
28’10’12’14’
GLCSL-FS-1000-15 (S or AL)-28-10GLCSL-FS-1000-15 (S or AL)-28-12GLCSL-FS-1000-15 (S or AL)-28-14
SteelSteelSteel
25’25’25’
131313
151515
212121
252525
14 1/814 1/814 1/8
7 7/87 7/87 7/8
23 3/823 3/823 3/8
16’-6”16’-6”16’-8”
12’-1 1/2”14’-1 1/2”16’-1 1/2”
445
222
33’
10’10’12’12’14’14’
GLCS-FS-1000-15 (S or AL)-33-10AL-FS-1000-15-33-10
GLCS-FS-1000-15 (S or AL)-33-12AL-FS-1000-15-33-12
GLCS-FS-1000-15 (S or AL)-33-14AL-FS-1000-15-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
131913191319
151515151515
18 1/822 1/818 1/822 1/818 1/822 1/8
22 1/8-
22 1/8-
22 1/8-
14 1/813 1/814 1/813 1/814 1/813 1/8
7 7/87 7/87 7/87 7/87 7/87 7/8
23 3/824 1/423 3/824 1/423 3/824 1/4
16’-6”16’-6”16’-6”16’-6”16’-8”16’-8”
11’-10 5/8”12’-2 5/8”
13’-10 5/8”14’-2 5/8”
15’-10 5/8”16’-2 5/8”
444455
333333
34’10’12’14’
GLCSLX-FS-1000-15 (S or AL)-34-10GLCSLX-FS-1000-15 (S or AL)-34-12GLCSLX-FS-1000-15 (S or AL)-34-14
SteelSteelSteel
30’30’30’
131313
151515
24 1/824 1/824 1/8
28 1/828 1/828 1/8
14 1/814 1/814 1/8
7 7/87 7/87 7/8
23 3/823 3/823 3/8
16’-6”16’-6”16’-8”
12’-4 5/8”14’-4 5/8”16’-4 5/8”
445
222
43’
10’10’12’12’14’14’
GLCS-FS-1000-15 (S or AL)-43-10AL-FS-1000-15-43-10
GLCS-FS-1000-15 (S or AL)-43-12AL-FS-1000-15-43-12
GLCS-FS-1000-15 (S or AL)-43-14AL-FS-1000-15-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
192619261926
151515151515
18 1/822 1/818 1/822 1/818 1/822 1/8
22 1/8-
22 1/8-
22 1/8-
14 1/813 1/814 1/813 1/814 1/813 1/8
7 7/87 7/87 7/87 7/87 7/87 7/8
23 3/824 1/423 3/824 1/423 3/824 1/4
16’-6”16’-6”16’-6”16’-6”16’-8”16’-8”
11’-10 5/8”12’-2 5/8”
13’-10 5/8”14’-2 5/8”
15’-10 5/8”16’-2 5/8”
444455
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-1000-15 (S or AL)-53-10AL-FS-1000-15-53-10
GLCSL-FS-1000-15 (S or AL)-53-10GLCS-FS-1000-15 (S or AL)-53-12
AL-FS-1000-15-53-12GLCSL-FS-1000-15 (S or AL)-53-12GLCS-FS-1000-15 (S or AL)-53-14
AL-FS-1000-15-53-14GLCSL-FS-1000-15 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
193019193019193019
151515151515151515
18 1/822 1/8
2118 1/822 1/8
2118 1/822 1/8
21
22 1/8-
2522 1/8
-25
22 1/8-
25
14 1/813 1/814 1/814 1/813 1/814 1/814 1/813 1/814 1/8
7 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/8
23 3/824 1/423 3/823 3/824 1/423 3/823 3/824 1/423 3/8
16’-6”16’-6”16’-6”16’-6”16’-6”16’-6”16’-8”16’-8”16’-8”
11’-10 5/8”12’-2 5/8”12’-1 1/2”
13’-10 5/8”14’-2 5/8”14’-1 1/2”
15’-10 5/8”16’-2 5/8”16’-1 1/2”
444444555
443443443
63’
10’10’12’12’14’14’
GLCS-FS-1000-15 (S or AL)-63-10AL-FS-1000-15-63-10
GLCS-FS-1000-15 (S or AL)-63-12AL-FS-1000-15-63-12
GLCS-FS-1000-15 (S or AL)-63-14AL-FS-1000-15-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
263626362636
151515151515
18 1/822 1/818 1/822 1/818 1/822 1/8
22 1/8-
22 1/8-
22 1/8-
14 1/813 1/814 1/813 1/814 1/813 1/8
7 7/87 7/87 7/87 7/87 7/87 7/8
23 3/824 1/423 3/824 1/423 3/824 1/4
16’-6”16’-6”16’-6”16’-6”16’-8”16’-8”
11’-10 5/8”12’-2 5/8”
13’-10 5/8”14’-2 5/8”
15’-10 5/8”16’-2 5/8”
444455
444444
64’10’12’14’
GLCSLX-FS-1000-15 (S or AL)-64-10GLCSLX-FS-1000-15 (S or AL)-64-12GLCSLX-FS-1000-15 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
151515
24 1/824 1/824 1/8
28 1/828 1/828 1/8
14 1/814 1/814 1/8
7 7/87 7/87 7/8
24 1/424 1/424 1/4
16’-6”16’-6”16’-8”
12’-4 5/8”14’-4 5/8”16’-4 5/8”
445
333
78’10’12’14’
GLCSL-FS-1000-15 (S or AL)-78-10GLCSL-FS-1000-15 (S or AL)-78-12GLCSL-FS-1000-15 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
151515
212121
252525
14 1/814 1/814 1/8
7 7/87 7/87 7/8
24 1/424 1/424 1/4
16’-6”16’-6”16’-8”
12’-1 1/2”14’-1 1/2”16’-1 1/2”
445
444
83’
10’10’12’12’14’14’
GLCS-FS-1000-15 (S or AL)-83-10AL-FS-1000-15-83-10
GLCS-FS-1000-15 (S or AL)-83-12AL-FS-1000-15-83-12
GLCS-FS-1000-15 (S or AL)-83-14AL-FS-1000-15-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
151515151515
18 1/822 1/818 1/822 1/818 1/822 1/8
22 1/8-
22 1/8-
22 1/8-
14 1/813 1/814 1/813 1/814 1/813 1/8
7 7/87 7/87 7/87 7/87 7/87 7/8
24 1/424 1/424 1/424 1/424 1/424 1/4
16’-6”16’-6”16’-6”16’-6”16’-8”16’-8”
11’-10 5/8”12’-2 5/8”
13’-10 5/8”14’-2 5/8”
15’-10 5/8”16’-2 5/8”
444455
555555
94’10’12’14’
GLCSLX-FS-1000-15 (S or AL)-94-10GLCSLX-FS-1000-15 (S or AL)-94-12GLCSLX-FS-1000-15 (S or AL)-94-14
SteelSteelSteel
30’30’30’
545454
151515
24 1/824 1/824 1/8
28 1/828 1/828 1/8
14 1/814 1/814 1/8
7 7/87 7/87 7/8
24 1/424 1/424 1/4
16’-6”16’-6”16’-8”
12’-4 5/8”14’-4 5/8”16’-4 5/8”
445
444
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-1000-15 (S or AL)-103-10AL-FS-1000-15-103-10
GLCSL-FS-1000-15 (S or AL)-103-10GLCS-FS-1000-15 (S or AL)-103-12
AL-FS-1000-15-103-12GLCSL-FS-1000-15 (S or AL)-103-12GLCS-FS-1000-15 (S or AL)-103-14
AL-FS-1000-15-103-14GLCSL-FS-1000-15 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
151515151515151515
18 1/822 1/8
2118 1/822 1/8
2118 1/822 1/8
21
22 1/8-
2522 1/8
-25
22 1/8-
25
14 1/813 1/814 1/814 1/813 1/814 1/814 1/813 1/814 1/8
7 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/8
24 1/424 1/424 1/424 1/424 1/424 1/424 1/424 1/424 1/4
16’-6”16’-6”16’-6”16’-6”16’-6”16’-6”16’-8”16’-8”16’-8”
11’-10 5/8”12’-2 5/8”12’-1 1/2”
13’-10 5/8”14’-2 5/8”14’-1 1/2”
15’-10 5/8”16’-2 5/8”16’-1 1/2”
444444555
665665665
124’10’12’14’
GLCSLX-FS-1000-15 (S or AL)-124-10GLCSLX-FS-1000-15 (S or AL)-124-12GLCSLX-FS-1000-15 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
151515
24 1/824 1/824 1/8
28 1/828 1/828 1/8
14 1/814 1/814 1/8
7 7/87 7/87 7/8
24 1/424 1/424 1/4
16’-6”16’-6”16’-8”
12’-4 5/8”14’-4 5/8”16’-4 5/8”
445
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
FREE STANDING WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
20’
23’
10’10’12’12’14’14’
GLCS-FS-1000-20 (S or AL)-23-10AL-FS-1000-20-23-10
GLCS-FS-1000-20 (S or AL)-23-12AL-FS-1000-20-23-12
GLCS-FS-1000-20 (S or AL)-23-14AL-FS-1000-20-23-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9139
139
13
151515151515
18 1/822 1/818 1/822 1/818 1/822 1/8
22 1/8-
22 1/8-
22 1/8-
14 1/813 1/814 1/813 1/814 1/813 1/8
7 7/87 7/87 7/87 7/87 7/87 7/8
23 3/827 5/823 3/827 5/823 3/827 5/8
21’-6”21’-6”21’-6”21’-6”21’-8”21’-8”
11’-10 5/8”12’-2 5/8”
13’-10 5/8”14’-2 5/8”
15’-10 5/8”16’-2 5/8”
444455
222222
28’10’12’14’
GLCSL-FS-1000-20 (S or AL)-28-10GLCSL-FS-1000-20 (S or AL)-28-12GLCSL-FS-1000-20 (S or AL)-28-14
SteelSteelSteel
25’25’25’
131313
151515
212121
252525
14 1/814 1/814 1/8
7 7/87 7/87 7/8
23 3/823 3/823 3/8
21’-6”21’-6”21’-8”
12’-1 1/2”14’-1 1/2”16’-1 1/2”
445
222
33’
10’10’12’12’14’14’
GLCS-FS-1000-20 (S or AL)-33-10AL-FS-1000-20-33-10
GLCS-FS-1000-20 (S or AL)-33-12AL-FS-1000-20-33-12
GLCS-FS-1000-20 (S or AL)-33-14AL-FS-1000-20-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
131913191319
151515151515
18 1/822 1/818 1/822 1/818 1/822 1/8
22 1/8-
22 1/8-
22 1/8-
14 1/813 1/814 1/813 1/814 1/813 1/8
7 7/87 7/87 7/87 7/87 7/87 7/8
23 3/827 5/823 3/827 5/823 3/827 5/8
21’-6”21’-6”21’-6”21’-6”21’-8”21’-8”
11’-10 5/8”12’-2 5/8”
13’-10 5/8”14’-2 5/8”
15’-10 5/8”16’-2 5/8”
444455
333333
34’10’12’14’
GLCSLX-FS-1000-20 (S or AL)-34-10GLCSLX-FS-1000-20 (S or AL)-34-12GLCSLX-FS-1000-20 (S or AL)-34-14
SteelSteelSteel
30’30’30’
131313
151515
24 1/824 1/824 1/8
28 1/828 1/828 1/8
14 1/814 1/814 1/8
7 7/87 7/87 7/8
23 3/823 3/823 3/8
21’-6”21’-6”21’-8”
12’-4 5/8”14’-4 5/8”16’-5 5/8”
445
222
43’
10’10’12’12’14’14’
GLCS-FS-1000-20 (S or AL)-43-10AL-FS-1000-20-43-10
GLCS-FS-1000-20 (S or AL)-43-12AL-FS-1000-20-43-12
GLCS-FS-1000-20 (S or AL)-43-14AL-FS-1000-20-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
192619261926
151515151515
18 1/822 1/818 1/822 1/818 1/822 1/8
22 1/8-
22 1/8-
22 1/8-
14 1/813 1/814 1/813 1/814 1/813 1/8
7 7/87 7/87 7/87 7/87 7/87 7/8
23 3/827 5/823 3/827 5/823 3/827 5/8
21’-6”21’-6”21’-6”21’-6”21’-8”21’-8”
11’-10 5/8”12’-2 5/8”
13’-10 5/8”14’-2 5/8”
15’-10 5/8”16’-2 5/8”
444455
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-1000-20 (S or AL)-53-10AL-FS-1000-20-53-10
GLCSL-FS-1000-20 (S or AL)-53-10GLCS-FS-1000-20 (S or AL)-53-12
AL-FS-1000-20-53-12GLCSL-FS-1000-20 (S or AL)-53-12GLCS-FS-1000-20 (S or AL)-53-14
AL-FS-1000-20-53-14GLCSL-FS-1000-20 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
193019193019193019
151515151515151515
18 1/822 1/8
2118 1/822 1/8
2118 1/822 1/8
21
22 1/8-
2522 1/8
-25
22 1/8-
25
14 1/813 1/814 1/814 1/813 1/814 1/814 1/813 1/814 1/8
7 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/8
23 3/827 5/823 3/823 3/827 5/823 3/823 3/827 5/823 3/8
21’-6”21’-6”21’-6”21’-6”21’-6”21’-6”21’-8”21’-8”21’-8”
11’-10 5/8”12’-2 5/8”12’-1 1/2”
13’-10 5/8”14’-2 5/8”14’-1 1/2”
15’-10 5/8”16’-2 5/8”16’-1 1/2”
444444555
443443443
63’
10’10’12’12’14’14’
GLCS-FS-1000-20 (S or AL)-63-10AL-FS-1000-20-63-10
GLCS-FS-1000-20 (S or AL)-63-12AL-FS-1000-20-63-12
GLCS-FS-1000-20 (S or AL)-63-14AL-FS-1000-20-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
263626362636
151515151515
18 1/822 1/818 1/822 1/818 1/822 1/8
22 1/8-
22 1/8-
22 1/8-
14 1/813 1/814 1/813 1/814 1/813 1/8
7 7/87 7/87 7/87 7/87 7/87 7/8
23 3/827 5/823 3/827 5/823 3/827 5/8
21’-6”21’-6”21’-6”21’-6”21’-8”21’-8”
11’-10 5/8”12’-2 5/8”
13’-10 5/8”14’-2 5/8”
15’-10 5/8”16’-2 5/8”
444455
444444
64’10’12’14’
GLCSLX-FS-1000-20 (S or AL)-64-10GLCSLX-FS-1000-20 (S or AL)-64-12GLCSLX-FS-1000-20 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
151515
24 1/824 1/824 1/8
28 1/828 1/828 1/8
14 1/814 1/814 1/8
7 7/87 7/87 7/8
27 5/827 5/827 5/8
21’-6”21’-6”21’-8”
12’-4 5/8”14’-4 5/8”16’-5 5/8”
445
333
78’10’12’14’
GLCSL-FS-1000-20 (S or AL)-78-10GLCSL-FS-1000-20 (S or AL)-78-12GLCSL-FS-1000-20 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
151515
212121
252525
14 1/814 1/814 1/8
7 7/87 7/87 7/8
27 5/827 5/827 5/8
21’-6”21’-6”21’-8”
12’-1 1/2”14’-1 1/2”16’-1 1/2”
445
444
83’
10’10’12’12’14’14’
GLCS-FS-1000-20 (S or AL)-83-10AL-FS-1000-20-83-10
GLCS-FS-1000-20 (S or AL)-83-12AL-FS-1000-20-83-12
GLCS-FS-1000-20 (S or AL)-83-14AL-FS-1000-20-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
151515151515
18 1/822 1/818 1/822 1/818 1/822 1/8
22 1/8-
22 1/8-
22 1/8-
14 1/813 1/814 1/813 1/814 1/813 1/8
7 7/87 7/87 7/87 7/87 7/87 7/8
27 5/827 5/827 5/827 5/827 5/827 5/8
21’-6”21’-6”21’-6”21’-6”21’-8”21’-8”
11’-10 5/8”12’-2 5/8”
13’-10 5/8”14’-2 5/8”
15’-10 5/8”16’-2 5/8”
444455
555555
94’10’12’14’
GLCSLX-FS-1000-20 (S or AL)-94-10GLCSLX-FS-1000-20 (S or AL)-94-12GLCSLX-FS-1000-20 (S or AL)-94-14
SteelSteelSteel
30’30’30’
545454
151515
24 1/824 1/824 1/8
28 1/828 1/828 1/8
14 1/814 1/814 1/8
7 7/87 7/87 7/8
27 5/827 5/827 5/8
21’-6”21’-6”21’-8”
12’-4 5/8”14’-4 5/8”16’-5 5/8”
445
444
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-1000-20 (S or AL)-103-10AL-FS-1000-20-103-10
GLCSL-FS-1000-20 (S or AL)-103-10GLCS-FS-1000-20 (S or AL)-103-12
AL-FS-1000-20-103-12GLCSL-FS-1000-20 (S or AL)-103-12GLCS-FS-1000-20 (S or AL)-103-14
AL-FS-1000-20-103-14GLCSL-FS-1000-20 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
151515151515151515
18 1/822 1/8
2118 1/822 1/8
2118 1/822 1/8
21
22 1/8-
2522 1/8
-25
22 1/8-
25
14 1/813 1/814 1/814 1/813 1/814 1/814 1/813 1/814 1/8
7 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/8
27 5/827 5/827 5/827 5/827 5/827 5/827 5/827 5/827 5/8
21’-6”21’-6”21’-6”21’-6”21’-6”21’-6”21’-8”21’-8”21’-8”
11’-10 5/8”12’-2 5/8”12’-1 1/2”
13’-10 5/8”14’-2 5/8”14’-1 1/2”
15’-10 5/8”16’-2 5/8”16’-1 1/2”
444444555
665665665
124’10’12’14’
GLCSLX-FS-1000-20 (S or AL)-124-10GLCSLX-FS-1000-20 (S or AL)-124-12GLCSLX-FS-1000-20 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
151515
24 1/824 1/824 1/8
28 1/828 1/828 1/8
14 1/814 1/814 1/8
7 7/87 7/87 7/8
27 5/827 5/827 5/8
21’-6”21’-6”21’-8”
12’-4 5/8”14’-4 5/8”16’-5 5/8”
445
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
1000# CAPACITYFR
EE S
TAN
DIN
G W
OR
KST
ATIO
N C
RA
NES
19
FREE STA
ND
ING
WO
RK
STATION
CR
AN
ES
20
1000# CAPACITYFREE STANDING WORK STATION BRIDGE CRANES
BRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
23’
23’
10’10’12’12’14’14’
GLCS-FS-1000-23 (S or AL)-23-10AL-FS-1000-23-23-10
GLCS-FS-1000-23 (S or AL)-23-12AL-FS-1000-23-23-12
GLCS-FS-1000-23 (S or AL)-23-14AL-FS-1000-23-23-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9139
139
13
151515151515
18 1/822 1/818 1/822 1/818 1/822 1/8
22 1/8-
22 1/8-
22 1/8-
14 1/813 1/814 1/813 1/814 1/813 1/8
7 7/87 7/87 7/87 7/87 7/87 7/8
23 3/831
23 3/831
23 3/831
24’-6”24’-6”24’-6”24’-6”24’-8”24’-8”
11’-11 5/8”12’-3 5/8”
13’-11 5/8”14’-3 5/8”
15’-11 5/8”16’-3 5/8”
444455
222222
28’10’12’14’
GLCSL-FS-1000-23 (S or AL)-28-10GLCSL-FS-1000-23 (S or AL)-28-12GLCSL-FS-1000-23 (S or AL)-28-14
SteelSteelSteel
25’25’25’
131313
151515
212121
252525
14 1/814 1/814 1/8
7 7/87 7/87 7/8
23 3/823 3/823 3/8
24’-6”24’-6”24’-8”
12’-2 1/2”14’-2 1/2”16’-2 1/2”
445
222
33’
10’10’12’12’14’14’
GLCS-FS-1000-23 (S or AL)-33-10AL-FS-1000-23-33-10
GLCS-FS-1000-23 (S or AL)-33-12AL-FS-1000-23-33-12
GLCS-FS-1000-23 (S or AL)-33-14AL-FS-1000-23-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
131913191319
151515151515
18 1/822 1/818 1/822 1/818 1/822 1/8
22 1/8-
22 1/8-
22 1/8-
14 1/813 1/814 1/813 1/814 1/813 1/8
7 7/87 7/87 7/87 7/87 7/87 7/8
23 3/831
23 3/831
23 3/831
24’-6”24’-6”24’-6”24’-6”24’-8”24’-8”
11’-11 5/8”12’-3 5/8”
13’-11 5/8”14’-3 5/8”
15’-11 5/8”16’-3 5/8”
444455
333333
34’10’12’14’
GLCSLX-FS-1000-23 (S or AL)-34-10GLCSLX-FS-1000-23 (S or AL)-34-12GLCSLX-FS-1000-23 (S or AL)-34-14
SteelSteelSteel
30’30’30’
131313
151515
24 1/824 1/824 1/8
28 1/828 1/828 1/8
14 1/814 1/814 1/8
7 7/87 7/87 7/8
23 3/823 3/823 3/8
24’-6”24’-6”24’-8”
12’-5 5/8”14’-5 5/8”16’-5 5/8”
445
222
43’
10’10’12’12’14’14’
GLCS-FS-1000-23 (S or AL)-43-10AL-FS-1000-23-43-10
GLCS-FS-1000-23 (S or AL)-43-12AL-FS-1000-23-43-12
GLCS-FS-1000-23 (S or AL)-43-14AL-FS-1000-23-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
192619261926
151515151515
18 1/822 1/818 1/822 1/818 1/822 1/8
22 1/8-
22 1/8-
22 1/8-
14 1/813 1/814 1/813 1/814 1/813 1/8
7 7/87 7/87 7/87 7/87 7/87 7/8
23 3/831
23 3/831
23 3/831
24’-6”24’-6”24’-6”24’-6”24’-8”24’-8”
11’-11 5/8”12’-3 5/8”
13’-11 5/8”14’-3 5/8”
15’-11 5/8”16’-3 5/8”
444455
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-1000-23 (S or AL)-53-10AL-FS-1000-23-53-10
GLCSL-FS-1000-23 (S or AL)-53-10GLCS-FS-1000-23 (S or AL)-53-12
AL-FS-1000-23-53-12GLCSL-FS-1000-23 (S or AL)-53-12GLCS-FS-1000-23 (S or AL)-53-14
AL-FS-1000-23-53-14GLCSL-FS-1000-23 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
193019193019193019
151515151515151515
18 1/822 1/8
2118 1/822 1/8
2118 1/822 1/8
21
22 1/8-
2522 1/8
-25
22 1/8-
25
14 1/813 1/814 1/814 1/813 1/814 1/814 1/813 1/814 1/8
7 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/8
23 3/831
23 3/823 3/8
3123 3/823 3/8
3123 3/8
24’-6”24’-6”24’-6”24’-6”24’-6”24’-6”24’-8”24’-8”24’-8”
11’-11 5/8”12’-3 5/8”12’-2 1/2”
13’-11 5/8”14’-3 5/8”14’-2 1/2”
15’-11 5/8”16’-3 5/8”16’-2 1/2”
444444555
443443443
63’
10’10’12’12’14’14’
GLCS-FS-1000-23 (S or AL)-63-10AL-FS-1000-23-63-10
GLCS-FS-1000-23 (S or AL)-63-12AL-FS-1000-23-63-12
GLCS-FS-1000-23 (S or AL)-63-14AL-FS-1000-23-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
263626362636
151515151515
18 1/822 1/818 1/822 1/818 1/822 1/8
22 1/8-
22 1/8-
22 1/8-
14 1/813 1/814 1/813 1/814 1/813 1/8
7 7/87 7/87 7/87 7/87 7/87 7/8
23 3/831
23 3/831
23 3/831
24’-6”24’-6”24’-6”24’-6”24’-8”24’-8”
11’-11 5/8”12’-3 5/8”
13’-11 5/8”14’-3 5/8”
15’-11 5/8”16’-3 5/8”
444455
444444
64’10’12’14’
GLCSLX-FS-1000-23 (S or AL)-64-10GLCSLX-FS-1000-23 (S or AL)-64-12GLCSLX-FS-1000-23 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
151515
24 1/824 1/824 1/8
28 1/828 1/828 1/8
14 1/814 1/814 1/8
7 7/87 7/87 7/8
313131
24’-6”24’-6”24’-8”
12’-5 5/8”14’-5 5/8”16’-5 5/8”
445
333
78’10’12’14’
GLCSL-FS-1000-23 (S or AL)-78-10GLCSL-FS-1000-23 (S or AL)-78-12GLCSL-FS-1000-23 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
151515
212121
252525
14 1/814 1/814 1/8
7 7/87 7/87 7/8
313131
24’-6”24’-6”24’-8”
12’-2 1/2”14’-2 1/2”16’-2 1/2”
445
444
83’
10’10’12’12’14’14’
GLCS-FS-1000-23 (S or AL)-83-10AL-FS-1000-23-83-10
GLCS-FS-1000-23 (S or AL)-83-12AL-FS-1000-23-83-12
GLCS-FS-1000-23 (S or AL)-83-14AL-FS-1000-23-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
151515151515
18 1/822 1/818 1/822 1/818 1/822 1/8
22 1/8-
22 1/8-
22 1/8-
14 1/813 1/814 1/813 1/814 1/813 1/8
7 7/87 7/87 7/87 7/87 7/87 7/8
313131313131
24’-6”24’-6”24’-6”24’-6”24’-8”24’-8”
11’-11 5/8”12’-3 5/8”
13’-11 5/8”14’-3 5/8”
15’-11 5/8”16’-3 5/8”
444455
555555
94’10’12’14’
GLCSLX-FS-1000-23 (S or AL)-94-10GLCSLX-FS-1000-23 (S or AL)-94-12GLCSLX-FS-1000-23 (S or AL)-94-14
SteelSteelSteel
30’30’30’
545454
151515
24 1/824 1/824 1/8
28 1/828 1/828 1/8
14 1/814 1/814 1/8
7 7/87 7/87 7/8
313131
24’-6”24’-6”24’-8”
12’-5 5/8”14’-5 5/8”16’-5 5/8”
445
444
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-1000-23 (S or AL)-103-10AL-FS-1000-23-103-10
GLCSL-FS-1000-23 (S or AL)-103-10GLCS-FS-1000-23 (S or AL)-103-12
AL-FS-1000-23-103-12GLCSL-FS-1000-23 (S or AL)-103-12GLCS-FS-1000-23 (S or AL)-103-14
AL-FS-1000-23-103-14GLCSL-FS-1000-23 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
151515151515151515
18 1/822 1/8
2118 1/822 1/8
2118 1/822 1/8
21
22 1/8-
2522 1/8
-25
22 1/8-
25
14 1/813 1/814 1/814 1/813 1/814 1/814 1/813 1/814 1/8
7 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/8
313131313131313131
24’-6”24’-6”24’-6”24’-6”24’-6”24’-6”24’-8”24’-8”24’-8”
11’-11 5/8”12’-3 5/8”12’-2 1/2”
13’-11 5/8”14’-3 5/8”14’-2 1/2”
15’-11 5/8”16’-3 5/8”16’-2 1/2”
444444555
665665665
124’10’12’14’
GLCSLX-FS-1000-23 (S or AL)-124-10GLCSLX-FS-1000-23 (S or AL)-124-12GLCSLX-FS-1000-23 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
151515
24 1/824 1/824 1/8
28 1/828 1/828 1/8
14 1/814 1/814 1/8
7 7/87 7/87 7/8
313131
24’-6”24’-6”24’-8”
12’-5 5/8”14’-5 5/8”16’-5 5/8”
445
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
FREE STANDING WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
28’
23’
10’10’12’12’14’14’
GLCS-FS-1000-28 (S or AL)-23-10AL-FS-1000-28-23-10
GLCS-FS-1000-28 (S or AL)-23-12AL-FS-1000-28-23-12
GLCS-FS-1000-28 (S or AL)-23-14AL-FS-1000-28-23-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9139
139
13
21 1/821
21 1/821
21 1/821
20 1/223 5/820 1/223 5/820 1/223 5/8
23 3/4-
23 3/4-
23 3/4-
1715 1/4
1715 1/4
1715 1/4
7 7/87 7/87 7/87 7/87 7/87 7/8
33 3/837 3/433 3/837 3/433 3/837 3/4
29’-6”29’-6”29’-6”29’-6”29’-8”29’-8”
12’-1”12’-5 1/8”
14’-1”14’-5 1/8”
16’-1”16’-5 1/8”
444455
222222
28’10’12’14’
GLCSL-FS-1000-28 (S or AL)-28-10GLCSL-FS-1000-28 (S or AL)-28-12GLCSL-FS-1000-28 (S or AL)-28-14
SteelSteelSteel
25’25’25’
999
21 1/821 1/821 1/8
23 3/823 3/823 3/8
26 5/826 5/826 5/8
171717
7 7/87 7/87 7/8
33 3/833 3/833 3/8
29’-6”29’-6”29’-8”
12’-5 7/8”14’-5 7/8”16’-5 7/8”
445
222
33’
10’10’12’12’14’14’
GLCS-FS-1000-28 (S or AL)-33-10AL-FS-1000-28-33-10
GLCS-FS-1000-28 (S or AL)-33-12AL-FS-1000-28-33-12
GLCS-FS-1000-28 (S or AL)-33-14AL-FS-1000-28-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9199
199
19
21 1/821
21 1/821
21 1/821
20 1/223 5/820 1/223 5/820 1/223 5/8
23 3/4-
23 3/4-
23 3/4-
1715 1/4
1715 1/4
1715 1/4
7 7/87 7/87 7/87 7/87 7/87 7/8
33 3/837 3/433 3/837 3/433 3/837 3/4
29’-6”29’-6”29’-6”29’-6”29’-8”29’-8”
12’-1”12’-5 1/8”
14’-1”14’-5 1/8”
16’-1”16’-5 1/8”
444455
333333
34’10’12’14’
GLCSLX-FS-1000-28 (S or AL)-34-10GLCSLX-FS-1000-28 (S or AL)-34-12GLCSLX-FS-1000-28 (S or AL)-34-14
SteelSteelSteel
30’30’30’
999
21 1/821 1/821 1/8
26 1/226 1/226 1/2
29 3/429 3/429 3/4
171717
7 7/87 7/87 7/8
33 3/833 3/833 3/8
29’-6”29’-6”29’-8”
12’-8”14’-8”16’-8”
445
222
43’
10’10’12’12’14’14’
GLCS-FS-1000-28 (S or AL)-43-10AL-FS-1000-28-43-10
GLCS-FS-1000-28 (S or AL)-43-12AL-FS-1000-28-43-12
GLCS-FS-1000-28 (S or AL)-43-14AL-FS-1000-28-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
132613261326
21 1/821
21 1/821
21 1/821
20 1/223 5/820 1/223 5/820 1/223 5/8
23 3/4-
23 3/4-
23 3/4-
1715 1/4
1715 1/4
1715 1/4
7 7/87 7/87 7/87 7/87 7/87 7/8
33 3/837 3/433 3/837 3/433 3/837 3/4
29’-6”29’-6”29’-6”29’-6”29’-8”29’-8”
12’-1”12’-5 1/8”
14’-1”14’-5 1/8”
16’-1”16’-5 1/8”
444455
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-1000-28 (S or AL)-53-10AL-FS-1000-28-53-10
GLCSL-FS-1000-28 (S or AL)-53-10GLCS-FS-1000-28 (S or AL)-53-12
AL-FS-1000-28-53-12GLCSL-FS-1000-28 (S or AL)-53-12GLCS-FS-1000-28 (S or AL)-53-14
AL-FS-1000-28-53-14GLCSL-FS-1000-28 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
133013133013133013
21 1/821
21 1/821 1/8
2121 1/821 1/8
2121 1/8
20 1/223 5/823 3/820 1/223 5/823 3/820 1/223 5/823 3/8
23 3/4-
26 5/823 3/4
-26 5/823 3/4
-26 5/8
1715 1/4
1717
15 1/41717
15 1/417
7 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/8
33 3/837 3/433 3/833 3/837 3/433 3/833 3/837 3/433 3/8
29’-6”29’-6”29’-6”29’-6”29’-6”29’-6”29’-8”29’-8”29’-8”
12’-1”12’-5 1/8”12’-5 7/8”
14’-1”14’-5 1/8”14’-5 7/8”
16’-1”16’-5 1/8”16’-5 7/8”
444444555
443443443
63’
10’10’12’12’14’14’
GLCS-FS-1000-28 (S or AL)-63-10AL-FS-1000-28-63-10
GLCS-FS-1000-28 (S or AL)-63-12AL-FS-1000-28-63-12
GLCS-FS-1000-28 (S or AL)-63-14AL-FS-1000-28-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
193619361936
21 1/821
21 1/821
21 1/821
20 1/223 5/820 1/223 5/820 1/223 5/8
23 3/4-
23 3/4-
23 3/4-
1715 1/4
1715 1/4
1715 1/4
7 7/87 7/87 7/87 7/87 7/87 7/8
33 3/837 3/433 3/837 3/433 3/837 3/4
29’-6”29’-6”29’-6”29’-6”29’-8”29’-8”
12’-1”12’-5 1/8”
14’-1”14’-5 1/8”
16’-1”16’-5 1/8”
444455
444444
64’10’12’14’
GLCSLX-FS-1000-28 (S or AL)-64-10GLCSLX-FS-1000-28 (S or AL)-64-12GLCSLX-FS-1000-28 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
21 1/821 1/821 1/8
26 1/226 1/226 1/2
29 3/429 3/429 3/4
171717
7 7/87 7/87 7/8
37 3/437 3/437 3/4
29’-6”29’-6”29’-8”
12’-8”14’-8”16’-8”
445
333
78’10’12’14’
GLCSL-FS-1000-28 (S or AL)-78-10GLCSL-FS-1000-28 (S or AL)-78-12GLCSL-FS-1000-28 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
21 1/821 1/821 1/8
23 3/823 3/823 3/8
26 5/826 5/826 5/8
171717
7 7/87 7/87 7/8
37 3/437 3/437 3/4
29’-6”29’-6”29’-8”
12’-5 7/8”14’-5 7/8”16’-5 7/8”
445
444
83’
10’10’12’12’14’14’
GLCS-FS-1000-28 (S or AL)-83-10AL-FS-1000-28-83-10
GLCS-FS-1000-28 (S or AL)-83-12AL-FS-1000-28-83-12
GLCS-FS-1000-28 (S or AL)-83-14AL-FS-1000-28-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
21 1/821
21 1/821
21 1/821
20 1/223 5/820 1/223 5/820 1/223 5/8
23 3/4-
23 3/4-
23 3/4-
1715 1/4
1715 1/4
1715 1/4
7 7/87 7/87 7/87 7/87 7/87 7/8
37 3/437 3/437 3/437 3/437 3/437 3/4
29’-6”29’-6”29’-6”29’-6”29’-8”29’-8”
12’-1”12’-5 1/8”
14’-1”14’-5 1/8”
16’-1”16’-5 1/8”
444455
555555
94’10’12’14’
GLCSLX-FS-1000-28 (S or AL)-94-10GLCSLX-FS-1000-28 (S or AL)-94-12GLCSLX-FS-1000-28 (S or AL)-94-14
SteelSteelSteel
30’30’30’
545454
21 1/821 1/821 1/8
26 1/226 1/226 1/2
29 3/429 3/429 3/4
171717
7 7/87 7/87 7/8
37 3/437 3/437 3/4
29’-6”29’-6”29’-8”
12’-8”14’-8”16’-8”
445
444
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-1000-28 (S or AL)-103-10AL-FS-1000-28-103-10
GLCSL-FS-1000-28 (S or AL)-103-10GLCS-FS-1000-28 (S or AL)-103-12
AL-FS-1000-28-103-12GLCSL-FS-1000-28 (S or AL)-103-12GLCS-FS-1000-28 (S or AL)-103-14
AL-FS-1000-28-103-14GLCSL-FS-1000-28 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
21 1/821
21 1/821 1/8
2121 1/821 1/8
2121 1/8
20 1/223 5/823 3/820 1/223 5/823 3/820 1/223 5/823 3/8
23 3/4-
26 5/823 3/4
-26 5/823 3/4
-26 5/8
1715 1/4
1717
15 1/41717
15 1/417
7 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/8
37 3/437 3/437 3/437 3/437 3/437 3/437 3/437 3/437 3/4
29’-6”29’-6”29’-6”29’-6”29’-6”29’-6”29’-8”29’-8”29’-8”
12’-1”12’-5 1/8”12’-5 7/8”
14’-1”14’-5 1/8”14’-5 7/8”
16’-1”16’-5 1/8”16’-5 7/8”
444444555
665665665
124’10’12’14’
GLCSLX-FS-1000-28 (S or AL)-124-10GLCSLX-FS-1000-28 (S or AL)-124-12GLCSLX-FS-1000-28 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
21 1/821 1/821 1/8
26 1/226 1/226 1/2
29 3/429 3/429 3/4
171717
7 7/87 7/87 7/8
37 3/437 3/437 3/4
29’-6”29’-6”29’-8”
12’-8”14’-8”16’-8”
445
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
1000# CAPACITYFR
EE S
TAN
DIN
G W
OR
KST
ATIO
N C
RA
NES
21
FREE STA
ND
ING
WO
RK
STATION
CR
AN
ES
22
1000# CAPACITYFREE STANDING WORK STATION BRIDGE CRANES
BRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
34’
28’10’12’14’
GLCSL-FS-1000-34 (S or AL)-28-10GLCSL-FS-1000-34 (S or AL)-28-12GLCSL-FS-1000-34 (S or AL)-28-14
SteelSteelSteel
25’25’25’
131313
21 7/821 7/821 7/8
23 3/823 3/823 3/8
26 5/826 5/826 5/8
20 1/820 1/820 1/8
7 7/87 7/87 7/8
39 3/839 3/839 3/8
35’-6”35’-6”35’-8”
12’-6 7/8”14’-6 7/8”16’-6 7/8”
445
222
33’
10’10’12’12’14’14’
GLCS-FS-1000-34 (S or AL)-33-10AL-FS-1000-34-33-10
GLCS-FS-1000-34 (S or AL)-33-12AL-FS-1000-34-33-12
GLCS-FS-1000-34 (S or AL)-33-14AL-FS-1000-34-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9199
199
19
21 7/821
21 7/821
21 7/821
23 1/223 5/823 1/223 5/823 1/223 5/8
23 3/4-
23 3/4-
23 3/4-
20 1/816 3/420 1/816 3/420 1/816 3/4
7 7/87 7/87 7/87 7/87 7/87 7/8
39 3/844 1/239 3/844 1/239 3/844 1/2
35’-6”35’-6”35’-6”35’-6”35’-8”35’-8”
12’-6”12’-7 1/8”
14’-6”14’-7 1/8”
16’-6”16’-7 1/8”
444455
333333
34’10’12’14’
GLCSLX-FS-1000-34 (S or AL)-34-10GLCSLX-FS-1000-34 (S or AL)-34-12GLCSLX-FS-1000-34 (S or AL)-34-14
SteelSteelSteel
30’30’30’
999
21 7/821 7/821 7/8
26 1/226 1/226 1/2
29 3/429 3/429 3/4
20 1/820 1/820 1/8
7 7/87 7/87 7/8
39 3/839 3/839 3/8
35’-6”35’-6”35’-8”
12’-9”14’-9”16’-9”
445
222
43’
10’10’12’12’14’14’
GLCS-FS-1000-34 (S or AL)-43-10AL-FS-1000-34-43-10
GLCS-FS-1000-34 (S or AL)-43-12AL-FS-1000-34-43-12
GLCS-FS-1000-34 (S or AL)-43-14AL-FS-1000-34-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
132613261326
21 7/821
21 7/821
21 7/821
23 1/223 5/823 1/223 5/823 1/223 5/8
23 3/4-
23 3/4-
23 3/4-
20 1/816 3/420 1/816 3/420 1/816 3/4
7 7/87 7/87 7/87 7/87 7/87 7/8
39 3/844 1/239 3/844 1/239 3/844 1/2
35’-6”35’-6”35’-6”35’-6”35’-8”35’-8”
12’-6”12’-7 1/8”
14’-6”14’-7 1/8”
16’-6”16’-7 1/8”
444455
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-1000-34 (S or AL)-53-10AL-FS-1000-34-53-10
GLCSL-FS-1000-34 (S or AL)-53-10GLCS-FS-1000-34 (S or AL)-53-12
AL-FS-1000-34-53-12GLCSL-FS-1000-34 (S or AL)-53-12GLCS-FS-1000-34 (S or AL)-53-14
AL-FS-1000-34-53-14GLCSL-FS-1000-34 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
133013133013133013
21 7/821
21 7/821 7/8
2121 7/821 7/8
2121 7/8
23 1/223 5/823 3/823 1/223 5/823 3/823 1/223 5/823 3/8
23 3/4-
26 5/823 3/4
-26 5/823 3/4
-26 5/8
20 1/816 3/420 1/820 1/816 3/420 1/820 1/816 3/420 1/8
7 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/8
39 3/844 1/239 3/839 3/844 1/239 3/839 3/844 1/239 3/8
35’-6”35’-6”35’-6”35’-6”35’-6”35’-6”35’-8”35’-8”35’-8”
12’-6”12’-7 1/8”12’-6 7/8”
14’-6”14’-7 1/8”14’-6 7/8”
16’-6”16’-7 1/8”16’-6 7/8”
444444555
443443443
63’
10’10’12’12’14’14’
GLCS-FS-1000-34 (S or AL)-63-10AL-FS-1000-34-63-10
GLCS-FS-1000-34 (S or AL)-63-12AL-FS-1000-34-63-12
GLCS-FS-1000-34 (S or AL)-63-14AL-FS-1000-34-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
193619361936
21 7/821
21 7/821
21 7/821
23 1/223 5/823 1/223 5/823 1/223 5/8
23 3/4-
23 3/4-
23 3/4-
20 1/816 3/420 1/816 3/420 1/816 3/4
7 7/87 7/87 7/87 7/87 7/87 7/8
39 3/844 1/239 3/844 1/239 3/844 1/2
35’-6”35’-6”35’-6”35’-6”35’-8”35’-8”
12’-6”12’-7 1/8”
14’-6”14’-7 1/8”
16’-6”16’-7 1/8”
444455
444444
64’10’12’14’
GLCSLX-FS-1000-34 (S or AL)-64-10GLCSLX-FS-1000-34 (S or AL)-64-12GLCSLX-FS-1000-34 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
21 7/821 7/821 7/8
26 1/226 1/226 1/2
29 3/429 3/429 3/4
20 1/820 1/820 1/8
7 7/87 7/87 7/8
44 1/244 1/244 1/2
35’-6”35’-6”35’-8”
12’-9”14’-9”16’-9”
445
333
78’10’12’14’
GLCSL-FS-1000-34 (S or AL)-78-10GLCSL-FS-1000-34 (S or AL)-78-12GLCSL-FS-1000-34 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
21 7/821 7/821 7/8
23 3/823 3/823 3/8
26 5/826 5/826 5/8
20 1/820 1/820 1/8
7 7/87 7/87 7/8
44 1/244 1/244 1/2
35’-6”35’-6”35’-8”
12’-6 7/8”14’-6 7/8”16’-6 7/8”
445
444
83’
10’10’12’12’14’14’
GLCS-FS-1000-34 (S or AL)-83-10AL-FS-1000-34-83-10
GLCS-FS-1000-34 (S or AL)-83-12AL-FS-1000-34-83-12
GLCS-FS-1000-34 (S or AL)-83-14AL-FS-1000-34-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
21 7/821
21 7/821
21 7/821
23 1/223 5/823 1/223 5/823 1/223 5/8
23 3/4-
23 3/4-
23 3/4-
20 1/816 3/420 1/816 3/420 1/816 3/4
7 7/87 7/87 7/87 7/87 7/87 7/8
44 1/244 1/244 1/244 1/244 1/244 1/2
35’-6”35’-6”35’-6”35’-6”35’-8”35’-8”
12’-6”12’-7 1/8”
14’-6”14’-7 1/8”
16’-6”16’-7 1/8”
444455
555555
94’10’12’14’
GLCSLX-FS-1000-34 (S or AL)-94-10GLCSLX-FS-1000-34 (S or AL)-94-12GLCSLX-FS-1000-34 (S or AL)-94-14
SteelSteelSteel
30’30’30’
545454
21 7/821 7/821 7/8
26 1/226 1/226 1/2
29 3/429 3/429 3/4
20 1/820 1/820 1/8
7 7/87 7/87 7/8
44 1/244 1/244 1/2
35’-6”35’-6”35’-8”
12’-9”14’-9”16’-9”
445
444
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-1000-34 (S or AL)-103-10AL-FS-1000-34-103-10
GLCSL-FS-1000-34 (S or AL)-103-10GLCS-FS-1000-34 (S or AL)-103-12
AL-FS-1000-34-103-12GLCSL-FS-1000-34 (S or AL)-103-12GLCS-FS-1000-34 (S or AL)-103-14
AL-FS-1000-34-103-14GLCSL-FS-1000-34 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
21 7/821
21 7/821 7/8
2121 7/821 7/8
2121 7/8
23 1/223 5/823 3/823 1/223 5/823 3/823 1/223 5/823 3/8
23 3/4-
26 5/823 3/4
-26 5/823 3/4
-26 5/8
20 1/816 3/420 1/820 1/816 3/420 1/820 1/816 3/420 1/8
7 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/87 7/8
44 1/244 1/244 1/244 1/244 1/244 1/244 1/244 1/244 1/2
35’-6”35’-6”35’-6”35’-6”35’-6”35’-6”35’-8”35’-8”35’-8”
12’-6”12’-7 1/8”12’-6 7/8”
14’-6”14’-7 1/8”14’-6 7/8”
16’-6”16’-7 1/8”16’-6 7/8”
444444555
665665665
124’10’12’14’
GLCSLX-FS-1000-34 (S or AL)-124-10GLCSLX-FS-1000-34 (S or AL)-124-12GLCSLX-FS-1000-34 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
21 7/821 7/821 7/8
26 1/226 1/226 1/2
29 3/429 3/429 3/4
20 1/820 1/820 1/8
7 7/87 7/87 7/8
44 1/244 1/244 1/2
35’-6”35’-6”35’-8”
12’-9”14’-9”16’-9”
445
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
FREE STANDING WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H5in
L3in
L6in OAW OAH D
in
SPT*
10’
11’-6”10’12’15’
GLCS-FS-2000-10 (S or AL)-11.5-10GLCS-FS-2000-10 (S or AL)-11.5-12GLCS-FS-2000-10 (S or AL)-11.5-15
SteelSteelSteel
20’20’20’
999
16 1/816 1/816 1/8
19 5/819 5/819 5/8
252525
8 7/88 7/88 7/8
8 1/88 1/88 1/8
252525
11’-8”11’-8”11’-8”
12’-0 1/8”15’-0 1/8”16’-1 1/8”
555
222
23’
10’10’12’12’14’14’
GLCS-FS-2000-10 (S or AL)-23-10AL-FS-2000-10-23-10
GLCS-FS-2000-10 (S or AL)-23-12AL-FS-2000-10-23-12
GLCS-FS-2000-10 (S or AL)-23-14AL-FS-2000-10-23-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9139
139
13
16 1/817
16 1/817
16 1/817
19 5/825 1/419 5/825 1/419 5/825 1/4
24-
24-
24-
8 7/813 3/88 7/8
13 3/88 7/8
13 3/8
8 1/88
8 1/88
8 1/88
2417 5/8
2417 5/8
2417 5/8
11’-8”11’-8”11’-8”11’-8”11’-8”11’-8”
12’-0 1/8”12’-5 3/4”14’-0 1/8”14’-5 3/4”16’-1 1/8”16’-6 3/4”
555555
222222
28’10’12’14’
GLCSL-FS-2000-10 (S or AL)-28-10GLCSL-FS-2000-10 (S or AL)-28-12GLCSL-FS-2000-10 (S or AL)-28-14
SteelSteelSteel
25’25’25’
131313
16 1/816 1/816 1/8
232323
27 3/827 3/827 3/8
8 7/88 7/88 7/8
8 1/88 1/88 1/8
242424
11’-8”11’-8”11’-8”
12’-4 1/2”14’-4 1/2”16’-4 1/2”
555
222
33’
10’10’12’12’14’14’
GLCS-FS-2000-10 (S or AL)-33-10AL-FS-2000-10-33-10
GLCS-FS-2000-10 (S or AL)-33-12AL-FS-2000-10-33-12
GLCS-FS-2000-10 (S or AL)-33-14AL-FS-2000-10-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
131913191319
16 1/817
16 1/817
16 1/817
19 5/825 1/419 5/825 1/419 5/825 1/4
24-
24-
24-
8 7/813 3/88 7/8
13 3/88 7/8
13 3/8
8 1/88
8 1/88
8 1/88
2417 5/8
2417 5/8
2417 5/8
11’-8”11’-8”11’-8”11’-8”11’-8”11’-8”
12’-0 1/8”12’-5 3/4”14’-0 1/8”14’-5 3/4”16’-1 1/8”16’-6 3/4”
555555
333333
34’10’12’14’
GLCSLX-FS-2000-10 (S or AL)-34-10GLCSLX-FS-2000-10 (S or AL)-34-12GLCSLX-FS-2000-10 (S or AL)-34-14
SteelSteelSteel
30’30’30’
131313
16 1/816 1/816 1/8
25 5/825 5/825 5/8
303030
8 7/88 7/88 7/8
8 1/88 1/88 1/8
242424
11’-8”11’-8”11’-8”
12’-7 1/8”14’-7 1/8”16’-7 1/8”
555
222
43’
10’10’12’12’14’14’
GLCS-FS-2000-10 (S or AL)-43-10AL-FS-2000-10-43-10
GLCS-FS-2000-10 (S or AL)-43-12AL-FS-2000-10-43-12
GLCS-FS-2000-10 (S or AL)-43-14AL-FS-2000-10-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
192619261926
16 1/817
16 1/817
16 1/817
19 5/825 1/419 5/825 1/419 5/825 1/4
24-
24-
24-
8 7/813 3/88 7/8
13 3/88 7/8
13 3/8
8 1/88
8 1/88
8 1/88
2417 5/8
2417 5/8
2417 5/8
11’-8”11’-8”11’-8”11’-8”11’-8”11’-8”
12’-0 1/8”12’-5 3/4”14’-0 1/8”14’-5 3/4”16’-1 1/8”16’-6 3/4”
555555
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-2000-10 (S or AL)-53-10AL-FS-2000-10-53-10
GLCSL-FS-2000-10 (S or AL)-53-10GLCS-FS-2000-10 (S or AL)-53-12
AL-FS-2000-10-53-12GLCSL-FS-2000-10 (S or AL)-53-12GLCS-FS-2000-10 (S or AL)-53-14
AL-FS-2000-10-53-14GLCSL-FS-2000-10 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
193019193019193019
16 1/817
16 1/816 1/8
1716 1/816 1/8
1716 1/8
19 5/825 1/4
2319 5/825 1/4
2319 5/825 1/4
23
24-
27 3/824-
27 3/824-
27 3/8
8 7/813 3/88 7/88 7/8
13 3/88 7/88 7/8
13 3/88 7/8
8 1/88
8 1/88 1/8
88 1/88 1/8
88 1/8
2417 5/8
2424
17 5/82424
17 5/824
11’-8”11’-8”11’-8”11’-8”11’-8”11’-8”11’-8”11’-8”11’-8”
12’-0 1/8”12’-5 3/4”12’-4 1/2”14’-0 1/8”14’-5 3/4”14’-4 1/2”16’-1 1/8”16’-6 3/4”16’-4 1/2”
555555555
443443443
63’
10’10’12’12’14’14’
GLCS-FS-2000-10 (S or AL)-63-10AL-FS-2000-10-63-10
GLCS-FS-2000-10 (S or AL)-63-12AL-FS-2000-10-63-12
GLCS-FS-2000-10 (S or AL)-63-14AL-FS-2000-10-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
263626362636
16 1/817
16 1/817
16 1/817
19 5/825 1/419 5/825 1/419 5/825 1/4
24-
24-
24-
8 7/813 3/88 7/8
13 3/88 7/8
13 3/8
8 1/88
8 1/88
8 1/88
2417 5/8
2417 5/8
2417 5/8
11’-8”11’-8”11’-8”11’-8”11’-8”11’-8”
12’-0 1/8”12’-5 3/4”14’-0 1/8”14’-5 3/4”16’-1 1/8”16’-6 3/4”
555555
444444
64’10’12’14’
GLCSLX-FS-2000-10 (S or AL)-64-10GLCSLX-FS-2000-10 (S or AL)-64-12GLCSLX-FS-2000-10 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
16 1/816 1/816 1/8
25 5/825 5/825 5/8
303030
8 7/88 7/88 7/8
8 1/88 1/88 1/8
242424
11’-8”11’-8”11’-8”
12’-7 1/8”14’-7 1/8”16’-7 1/8”
555
333
78’10’12’14’
GLCSL-FS-2000-10 (S or AL)-78-10GLCSL-FS-2000-10 (S or AL)-78-12GLCSL-FS-2000-10 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
16 1/816 1/816 1/8
232323
27 3/827 3/827 3/8
8 7/88 7/88 7/8
8 1/88 1/88 1/8
242424
11’-8”11’-8”11’-8”
12’-4 1/2”14’-4 1/2”16’-4 1/2”
555
444
83’
10’10’12’12’14’14’
GLCS-FS-2000-10 (S or AL)-83-10AL-FS-2000-10-83-10
GLCS-FS-2000-10 (S or AL)-83-12AL-FS-2000-10-83-12
GLCS-FS-2000-10 (S or AL)-83-14AL-FS-2000-10-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
16 1/817
16 1/817
16 1/817
19 5/825 1/419 5/825 1/419 5/825 1/4
24-
24-
24-
8 7/813 3/88 7/8
13 3/88 7/8
13 3/8
8 1/88
8 1/88
8 1/88
2417 5/8
2417 5/8
2417 5/8
11’-8”11’-8”11’-8”11’-8”11’-8”11’-8”
12’-0 1/8”12’-5 3/4”14’-0 1/8”14’-5 3/4”16’-1 1/8”16’-6 3/4”
555555
555555
94’10’12’14’
GLCSLX-FS-2000-10 (S or AL)-94-10GLCSLX-FS-2000-10 (S or AL)-94-12GLCSLX-FS-2000-10 (S or AL)-94-14
SteelSteelSteel
30’30’30’
545454
16 1/816 1/816 1/8
25 5/825 5/825 5/8
303030
8 7/88 7/88 7/8
8 1/88 1/88 1/8
242424
11’-8”11’-8”11’-8”
12’-7 1/8”14’-7 1/8”16’-7 1/8”
555
444
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-2000-10 (S or AL)-103-10AL-FS-2000-10-103-10
GLCSL-FS-2000-10 (S or AL)-103-10GLCS-FS-2000-10 (S or AL)-103-12
AL-FS-2000-10-103-12GLCSL-FS-2000-10 (S or AL)-103-12GLCS-FS-2000-10 (S or AL)-103-14
AL-FS-2000-10-103-14GLCSL-FS-2000-10 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
16 1/817
16 1/816 1/8
1716 1/816 1/8
1716 1/8
19 5/825 1/4
2319 5/825 1/4
2319 5/825 1/4
23
24-
27 3/824-
27 3/824-
27 3/8
8 7/813 3/88 7/88 7/8
13 3/88 7/88 7/8
13 3/88 7/8
8 1/88
8 1/88 1/8
88 1/88 1/8
88 1/8
2417 5/8
2424
17 5/82424
17 5/824
11’-8”11’-8”11’-8”11’-8”11’-8”11’-8”11’-8”11’-8”11’-8”
12’-0 1/8”12’-5 3/4”12’-4 1/2”14’-0 1/8”14’-5 3/4”14’-4 1/2”16’-1 1/8”16’-6 3/4”16’-4 1/2”
555555555
665665665
124’10’12’14’
GLCSLX-FS-2000-10 (S or AL)-124-10GLCSLX-FS-2000-10 (S or AL)-124-12GLCSLX-FS-2000-10 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
16 1/816 1/816 1/8
25 5/825 5/825 5/8
303030
8 7/88 7/88 7/8
8 1/88 1/88 1/8
242424
11’-8”11’-8”11’-8”
12’-7 1/8”14’-7 1/8”16’-7 1/8”
555
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
2000# CAPACITYFR
EE S
TAN
DIN
G W
OR
KST
ATIO
N C
RA
NES
23
24
2000# CAPACITYFREE STANDING WORK STATION BRIDGE CRANES
BRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
15’
23’
10’10’12’12’14’14’
GLCS-FS-2000-15 (S or AL)-23-10AL-FS-2000-15-23-10
GLCS-FS-2000-15 (S or AL)-23-12AL-FS-2000-15-23-12
GLCS-FS-2000-15 (S or AL)-23-14AL-FS-2000-15-23-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9139
139
13
16 1/817
16 1/817
16 1/817
19 5/825 1/419 5/825 1/419 5/825 1/4
24-
24-
24-
14 7/813 3/814 7/813 3/814 7/813 3/8
8 1/88
8 1/88
8 1/88
2424 3/8
2424 3/8
2424 3/8
16’-8”16’-8”16’-8”16’-8”16’-8”16’-8”
12’-1 1/8”12’-6 3/4”14’-1 1/8”14’-6 3/4”16’-1 1/8”16’-6 3/4”
555555
222222
28’10’12’14’
GLCSL-FS-2000-15 (S or AL)-28-10GLCSL-FS-2000-15 (S or AL)-28-12GLCSL-FS-2000-15 (S or AL)-28-14
SteelSteelSteel
25’25’25’
131313
16 1/816 1/816 1/8
232323
27 3/827 3/827 3/8
14 7/814 7/814 7/8
8 1/88 1/88 1/8
242424
16’-8”16’-8”16’-8”
12’-4 1/2”14’-4 1/2”16’-4 1/2”
555
222
33’
10’10’12’12’14’14’
GLCS-FS-2000-15 (S or AL)-33-10AL-FS-2000-15-33-10
GLCS-FS-2000-15 (S or AL)-33-12AL-FS-2000-15-33-12
GLCS-FS-2000-15 (S or AL)-33-14AL-FS-2000-15-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
131913191319
16 1/817
16 1/817
16 1/817
19 5/825 1/419 5/825 1/419 5/825 1/4
24-
24-
24-
14 7/813 3/814 7/813 3/814 7/813 3/8
8 1/88
8 1/88
8 1/88
2424 3/8
2424 3/8
2424 3/8
16’-8”16’-8”16’-8”16’-8”16’-8”16’-8”
12’-1 1/8”12’-6 3/4”14’-1 1/8”14’-6 3/4”16’-1 1/8”16’-6 3/4”
555555
333333
34’10’12’14’
GLCSLX-FS-2000-15 (S or AL)-34-10GLCSLX-FS-2000-15 (S or AL)-34-12GLCSLX-FS-2000-15 (S or AL)-34-14
SteelSteelSteel
30’30’30’
131313
16 1/816 1/816 1/8
25 5/825 5/825 5/8
303030
14 7/814 7/814 7/8
8 1/88 1/88 1/8
242424
16’-8”16’-8”16’-8”
12’-7 1/8”14’-7 1/8”16’-8 1/8”
555
222
43’
10’10’12’12’14’14’
GLCS-FS-2000-15 (S or AL)-43-10AL-FS-2000-15-43-10
GLCS-FS-2000-15 (S or AL)-43-12AL-FS-2000-15-43-12
GLCS-FS-2000-15 (S or AL)-43-14AL-FS-2000-15-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
192619261926
16 1/817
16 1/817
16 1/817
19 5/825 1/419 5/825 1/419 5/825 1/4
24-
24-
24-
14 7/813 3/814 7/813 3/814 7/813 3/8
8 1/88
8 1/88
8 1/88
2424 3/8
2424 3/8
2424 3/8
16’-8”16’-8”16’-8”16’-8”16’-8”16’-8”
12’-1 1/8”12’-6 3/4”14’-1 1/8”14’-6 3/4”16’-1 1/8”16’-6 3/4”
555555
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-2000-15 (S or AL)-53-10AL-FS-2000-15-53-10
GLCSL-FS-2000-15 (S or AL)-53-10GLCS-FS-2000-15 (S or AL)-53-12
AL-FS-2000-15-53-12GLCSL-FS-2000-15 (S or AL)-53-12GLCS-FS-2000-15 (S or AL)-53-14
AL-FS-2000-15-53-14GLCSL-FS-2000-15 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
193019193019193019
16 1/817
16 1/816 1/8
1716 1/816 1/8
1716 1/8
19 5/825 1/4
2319 5/825 1/4
2319 5/825 1/4
23
24-
27 3/824-
27 3/824-
27 3/8
14 7/813 3/814 7/814 7/813 3/814 7/814 7/813 3/814 7/8
8 1/88
8 1/88 1/8
88 1/88 1/8
88 1/8
2424 3/8
2424
24 3/82424
24 3/824
16’-8”16’-8”16’-8”16’-8”16’-8”16’-8”16’-8”16’-8”16’-8”
12’-1 1/8”12’-6 3/4”12’-4 1/2”14’-1 1/8”14’-6 3/4”14’-4 1/2”16’-1 1/8”16’-6 3/4”16’-4 1/2”
555555555
443443443
63’
10’10’12’12’14’14’
GLCS-FS-2000-15 (S or AL)-63-10AL-FS-2000-15-63-10
GLCS-FS-2000-15 (S or AL)-63-12AL-FS-2000-15-63-12
GLCS-FS-2000-15 (S or AL)-63-14AL-FS-2000-15-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
263626362636
16 1/817
16 1/817
16 1/817
19 5/825 1/419 5/825 1/419 5/825 1/4
24-
24-
24-
14 7/813 3/814 7/813 3/814 7/813 3/8
8 1/88
8 1/88
8 1/88
2424 3/8
2424 3/8
2424 3/8
16’-8”16’-8”16’-8”16’-8”16’-8”16’-8”
12’-1 1/8”12’-6 3/4”14’-1 1/8”14’-6 3/4”16’-1 1/8”16’-6 3/4”
555555
444444
64’10’12’14’
GLCSLX-FS-2000-15 (S or AL)-64-10GLCSLX-FS-2000-15 (S or AL)-64-12GLCSLX-FS-2000-15 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
16 1/816 1/816 1/8
25 5/825 5/825 5/8
303030
14 7/814 7/814 7/8
8 1/88 1/88 1/8
24 3/824 3/824 3/8
16’-8”16’-8”16’-8”
12’-7 1/8”14’-7 1/8”16’-8 1/8”
555
333
78’10’12’14’
GLCSL-FS-2000-15 (S or AL)-78-10GLCSL-FS-2000-15 (S or AL)-78-12GLCSL-FS-2000-15 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
16 1/816 1/816 1/8
232323
27 3/827 3/827 3/8
14 7/814 7/814 7/8
8 1/88 1/88 1/8
24 3/824 3/824 3/8
16’-8”16’-8”16’-8”
12’-4 1/2”14’-4 1/2”16’-4 1/2”
555
444
83’
10’10’12’12’14’14’
GLCS-FS-2000-15 (S or AL)-83-10AL-FS-2000-15-83-10
GLCS-FS-2000-15 (S or AL)-83-12AL-FS-2000-15-83-12
GLCS-FS-2000-15 (S or AL)-83-14AL-FS-2000-15-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
16 1/817
16 1/817
16 1/817
19 5/825 1/419 5/825 1/419 5/825 1/4
24-
24-
24-
14 7/813 3/814 7/813 3/814 7/813 3/8
8 1/88
8 1/88
8 1/88
24 3/824 3/824 3/824 3/824 3/824 3/8
16’-8”16’-8”16’-8”16’-8”16’-8”16’-8”
12’-1 1/8”12’-6 3/4”14’-1 1/8”14’-6 3/4”16’-1 1/8”16’-6 3/4”
555555
555555
94’10’12’14’
GLCSLX-FS-2000-15 (S or AL)-94-10GLCSLX-FS-2000-15 (S or AL)-94-12GLCSLX-FS-2000-15 (S or AL)-94-14
SteelSteelSteel
30’30’30’
545454
16 1/816 1/816 1/8
25 5/825 5/825 5/8
303030
14 7/814 7/814 7/8
8 1/88 1/88 1/8
24 3/824 3/824 3/8
16’-8”16’-8”16’-8”
12’-7 1/8”14’-7 1/8”16’-8 1/8”
555
444
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-2000-15 (S or AL)-103-10AL-FS-2000-15-103-10
GLCSL-FS-2000-15 (S or AL)-103-10GLCS-FS-2000-15 (S or AL)-103-12
AL-FS-2000-15-103-12GLCSL-FS-2000-15 (S or AL)-103-12GLCS-FS-2000-15 (S or AL)-103-14
AL-FS-2000-15-103-14GLCSL-FS-2000-15 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
16 1/817
16 1/816 1/8
1716 1/816 1/8
1716 1/8
19 5/825 1/4
2319 5/825 1/4
2319 5/825 1/4
23
24-
27 3/824-
27 3/824-
27 3/8
14 7/813 3/814 7/814 7/813 3/814 7/814 7/813 3/814 7/8
8 1/88
8 1/88 1/8
88 1/88 1/8
88 1/8
24 3/824 3/824 3/824 3/824 3/824 3/824 3/824 3/824 3/8
16’-8”16’-8”16’-8”16’-8”16’-8”16’-8”16’-8”16’-8”16’-8”
12’-1 1/8”12’-6 3/4”12’-4 1/2”14’-1 1/8”14’-6 3/4”14’-4 1/2”16’-1 1/8”16’-6 3/4”16’-4 1/2”
555555555
665665665
124’10’12’14’
GLCSLX-FS-2000-15 (S or AL)-124-10GLCSLX-FS-2000-15 (S or AL)-124-12GLCSLX-FS-2000-15 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
16 1/816 1/816 1/8
25 5/825 5/825 5/8
303030
14 7/814 7/814 7/8
8 1/88 1/88 1/8
24 3/824 3/824 3/8
16’-8”16’-8”16’-8”
12’-7 1/8”14’-7 1/8”16’-8 1/8”
555
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
FREE STANDING WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
20’
23’
10’10’12’12’14’14’
GLCS-FS-2000-20 (S or AL)-23-10AL-FS-2000-20-23-10
GLCS-FS-2000-20 (S or AL)-23-12AL-FS-2000-20-23-12
GLCS-FS-2000-20 (S or AL)-23-14AL-FS-2000-20-23-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9139
139
13
16 1/817
16 1/817
16 1/817
19 5/825 1/419 5/825 1/419 5/825 1/4
24-
24-
24-
14 7/815 1/214 7/815 1/214 7/815 1/2
8 1/88
8 1/88
8 1/88
2427 3/4
2427 3/4
2427 3/4
21’-8”21’-8”21’-8”21’-8”21’-8”21’-8”
12’-1 1/8”12’-6 3/4”14’-1 1/8”14’-6 3/4”16’-2 1/8”16’-7 3/4”
555555
222222
28’10’12’14’
GLCSL-FS-2000-20 (S or AL)-28-10GLCSL-FS-2000-20 (S or AL)-28-12GLCSL-FS-2000-20 (S or AL)-28-14
SteelSteelSteel
25’25’25’
131313
16 1/816 1/816 1/8
232323
27 3/827 3/827 3/8
14 7/814 7/814 7/8
8 1/88 1/88 1/8
242424
21’-8”21’-8”21’-8”
12’-4 1/2”14’-4 1/2”16’-5 1/2”
555
222
33’
10’10’12’12’14’14’
GLCS-FS-2000-20 (S or AL)-33-10AL-FS-2000-20-33-10
GLCS-FS-2000-20 (S or AL)-33-12AL-FS-2000-20-33-12
GLCS-FS-2000-20 (S or AL)-33-14AL-FS-2000-20-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
131913191319
16 1/817
16 1/817
16 1/817
19 5/825 1/419 5/825 1/419 5/825 1/4
24-
24-
24-
14 7/815 1/214 7/815 1/214 7/815 1/2
8 1/88
8 1/88
8 1/88
2427 3/4
2427 3/4
2427 3/4
21’-8”21’-8”21’-8”21’-8”21’-8”21’-8”
12’-1 1/8”12’-6 3/4”14’-1 1/8”14’-6 3/4”16’-2 1/8”16’-7 3/4”
555555
333333
34’10’12’14’
GLCSLX-FS-2000-20 (S or AL)-34-10GLCSLX-FS-2000-20 (S or AL)-34-12GLCSLX-FS-2000-20 (S or AL)-34-14
SteelSteelSteel
30’30’30’
131313
16 1/816 1/816 1/8
25 5/825 5/825 5/8
303030
14 7/814 7/814 7/8
8 1/88 1/88 1/8
242424
21’-8”21’-8”21’-8”
12’-7 1/8”14’-7 1/8”16’-8 1/8”
555
222
43’
10’10’12’12’14’14’
GLCS-FS-2000-20 (S or AL)-43-10AL-FS-2000-20-43-10
GLCS-FS-2000-20 (S or AL)-43-12AL-FS-2000-20-43-12
GLCS-FS-2000-20 (S or AL)-43-14AL-FS-2000-20-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
192619261926
16 1/817
16 1/817
16 1/817
19 5/825 1/419 5/825 1/419 5/825 1/4
24-
24-
24-
14 7/815 1/214 7/815 1/214 7/815 1/2
8 1/88
8 1/88
8 1/88
2427 3/4
2427 3/4
2427 3/4
21’-8”21’-8”21’-8”21’-8”21’-8”21’-8”
12’-1 1/8”12’-6 3/4”14’-1 1/8”14’-6 3/4”16’-2 1/8”16’-7 3/4”
555555
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-2000-20 (S or AL)-53-10AL-FS-2000-20-53-10
GLCSL-FS-2000-20 (S or AL)-53-10GLCS-FS-2000-20 (S or AL)-53-12
AL-FS-2000-20-53-12GLCSL-FS-2000-20 (S or AL)-53-12GLCS-FS-2000-20 (S or AL)-53-14
AL-FS-2000-20-53-14GLCSL-FS-2000-20 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
193019193019193019
16 1/817
16 1/816 1/8
1716 1/816 1/8
1716 1/8
19 5/825 1/4
2319 5/825 1/4
2319 5/825 1/4
23
24-
27 3/824-
27 3/824-
27 3/8
14 7/815 1/214 7/814 7/815 1/214 7/814 7/815 1/214 7/8
8 1/88
8 1/88 1/8
88 1/88 1/8
88 1/8
2427 3/4
2424
27 3/42424
27 3/424
21’-8”21’-8”21’-8”21’-8”21’-8”21’-8”21’-8”21’-8”21’-8”
12’-1 1/8”12’-6 3/4”12’-4 1/2”14’-1 1/8”14’-6 3/4”14’-4 1/2”16’-2 1/8”16’-7 3/4”16’-5 1/2”
555555555
443443443
63’
10’10’12’12’14’14’
GLCS-FS-2000-20 (S or AL)-63-10AL-FS-2000-20-63-10
GLCS-FS-2000-20 (S or AL)-63-12AL-FS-2000-20-63-12
GLCS-FS-2000-20 (S or AL)-63-14AL-FS-2000-20-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
263626362636
16 1/817
16 1/817
16 1/817
19 5/825 1/419 5/825 1/419 5/825 1/4
24-
24-
24-
14 7/815 1/214 7/815 1/214 7/815 1/2
8 1/88
8 1/88
8 1/88
2427 3/4
2427 3/4
2427 3/4
21’-8”21’-8”21’-8”21’-8”21’-8”21’-8”
12’-1 1/8”12’-6 3/4”14’-1 1/8”14’-6 3/4”16’-2 1/8”16’-7 3/4”
555555
444444
64’10’12’14’
GLCSLX-FS-2000-20 (S or AL)-64-10GLCSLX-FS-2000-20 (S or AL)-64-12GLCSLX-FS-2000-20 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
16 1/816 1/816 1/8
25 5/825 5/825 5/8
303030
14 7/814 7/814 7/8
8 1/88 1/88 1/8
27 3/427 3/427 3/4
21’-8”21’-8”21’-8”
12’-7 1/8”14’-7 1/8”16’-8 1/8”
555
333
78’10’12’14’
GLCSL-FS-2000-20 (S or AL)-78-10GLCSL-FS-2000-20 (S or AL)-78-12GLCSL-FS-2000-20 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
16 1/816 1/816 1/8
232323
27 3/827 3/827 3/8
14 7/814 7/814 7/8
8 1/88 1/88 1/8
27 3/427 3/427 3/4
21’-8”21’-8”21’-8”
12’-4 1/2”14’-4 1/2”16’-5 1/2”
555
444
83’
10’10’12’12’14’14’
GLCS-FS-2000-20 (S or AL)-83-10AL-FS-2000-20-83-10
GLCS-FS-2000-20 (S or AL)-83-12AL-FS-2000-20-83-12
GLCS-FS-2000-20 (S or AL)-83-14AL-FS-2000-20-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
16 1/817
16 1/817
16 1/817
19 5/825 1/419 5/825 1/419 5/825 1/4
24-
24-
24-
14 7/815 1/214 7/815 1/214 7/815 1/2
8 1/88
8 1/88
8 1/88
27 3/427 3/427 3/427 3/427 3/427 3/4
21’-8”21’-8”21’-8”21’-8”21’-8”21’-8”
12’-1 1/8”12’-6 3/4”14’-1 1/8”14’-6 3/4”16’-2 1/8”16’-7 3/4”
555555
555555
94’10’12’14’
GLCSLX-FS-2000-20 (S or AL)-94-10GLCSLX-FS-2000-20 (S or AL)-94-12GLCSLX-FS-2000-20 (S or AL)-94-14
SteelSteelSteel
30’30’30’
545454
16 1/816 1/816 1/8
25 5/825 5/825 5/8
303030
14 7/814 7/814 7/8
8 1/88 1/88 1/8
27 3/427 3/427 3/4
21’-8”21’-8”21’-8”
12’-7 1/8”14’-7 1/8”16’-8 1/8”
555
444
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-2000-20 (S or AL)-103-10AL-FS-2000-20-103-10
GLCSL-FS-2000-20 (S or AL)-103-10GLCS-FS-2000-20 (S or AL)-103-12
AL-FS-2000-20-103-12GLCSL-FS-2000-20 (S or AL)-103-12GLCS-FS-2000-20 (S or AL)-103-14
AL-FS-2000-20-103-14GLCSL-FS-2000-20 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
16 1/817
16 1/816 1/8
1716 1/816 1/8
1716 1/8
19 5/825 1/4
2319 5/825 1/4
2319 5/825 1/4
23
24-
27 3/824-
27 3/824-
27 3/8
14 7/815 1/214 7/814 7/815 1/214 7/814 7/815 1/214 7/8
8 1/88
8 1/88 1/8
88 1/88 1/8
88 1/8
27 3/427 3/427 3/427 3/427 3/427 3/427 3/427 3/427 3/4
21’-8”21’-8”21’-8”21’-8”21’-8”21’-8”21’-8”21’-8”21’-8”
12’-1 1/8”12’-6 3/4”12’-4 1/2”14’-1 1/8”14’-6 3/4”14’-4 1/2”16’-2 1/8”16’-7 3/4”16’-5 1/2”
555555555
665665665
124’10’12’14’
GLCSLX-FS-2000-20 (S or AL)-124-10GLCSLX-FS-2000-20 (S or AL)-124-12GLCSLX-FS-2000-20 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
16 1/816 1/816 1/8
25 5/825 5/825 5/8
303030
14 7/814 7/814 7/8
8 1/88 1/88 1/8
27 3/427 3/427 3/4
21’-8”21’-8”21’-8”
12’-7 1/8”14’-7 1/8”16’-8 1/8”
555
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
2000# CAPACITYFR
EE S
TAN
DIN
G W
OR
KST
ATIO
N C
RA
NES
25
FREE STA
ND
ING
WO
RK
STATION
CR
AN
ES
26
2000# CAPACITYFREE STANDING WORK STATION BRIDGE CRANES
BRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
23’
23’
10’10’12’12’14’14’
GLCS-FS-2000-23 (S or AL)-23-10AL-FS-2000-23-23-10
GLCS-FS-2000-23 (S or AL)-23-12AL-FS-2000-23-23-12
GLCS-FS-2000-23 (S or AL)-23-14AL-FS-2000-23-23-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9139
139
13
16 1/817
16 1/817
16 1/817
19 5/825 1/419 5/825 1/419 5/825 1/4
24-
24-
24-
14 7/815 1/214 7/815 1/214 7/815 1/2
8 1/88
8 1/88
8 1/88
2431 1/8
2431 1/8
2431 1/8
24’-8”24’-8”24’-8”24’-8”24’-8”24’-8”
12’-1 1/8”12’-6 3/4”14’-2 1/8”14’-7 3/4”16’-2 1/8”16’-7 3/4”
555555
222222
28’10’12’14’
GLCSL-FS-2000-23 (S or AL)-28-10GLCSL-FS-2000-23 (S or AL)-28-12GLCSL-FS-2000-23 (S or AL)-28-14
SteelSteelSteel
25’25’25’
131313
16 1/816 1/816 1/8
232323
27 3/827 3/827 3/8
14 7/814 7/814 7/8
8 1/88 1/88 1/8
242424
24’-8”24’-8”24’-8”
12’-4 1/2”14’-5 1/2”16’-6 1/2”
555
222
33’
10’10’12’12’14’14’
GLCS-FS-2000-23 (S or AL)-33-10AL-FS-2000-23-33-10
GLCS-FS-2000-23 (S or AL)-33-12AL-FS-2000-23-33-12
GLCS-FS-2000-23 (S or AL)-33-14AL-FS-2000-23-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
131913191319
16 1/817
16 1/817
16 1/817
19 5/825 1/419 5/825 1/419 5/825 1/4
24-
24-
24-
14 7/815 1/214 7/815 1/214 7/815 1/2
8 1/88
8 1/88
8 1/88
2431 1/8
2431 1/8
2431 1/8
24’-8”24’-8”24’-8”24’-8”24’-8”24’-8”
12’-1 1/8”12’-6 3/4”14’-2 1/8”14’-7 3/4”16’-2 1/8”16’-7 3/4”
555555
333333
34’10’12’14’
GLCSLX-FS-2000-23 (S or AL)-34-10GLCSLX-FS-2000-23 (S or AL)-34-12GLCSLX-FS-2000-23 (S or AL)-34-14
SteelSteelSteel
30’30’30’
131313
16 1/816 1/816 1/8
25 5/825 5/825 5/8
303030
14 7/814 7/814 7/8
8 1/88 1/88 1/8
242424
24’-8”24’-8”24’-8”
12’-7 1/8”14’-8 1/8”16’-9 1/8”
555
222
43’
10’10’12’12’14’14’
GLCS-FS-2000-23 (S or AL)-43-10AL-FS-2000-23-43-10
GLCS-FS-2000-23 (S or AL)-43-12AL-FS-2000-23-43-12
GLCS-FS-2000-23 (S or AL)-43-14AL-FS-2000-23-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
192619261926
16 1/817
16 1/817
16 1/817
19 5/825 1/419 5/825 1/419 5/825 1/4
24-
24-
24-
14 7/815 1/214 7/815 1/214 7/815 1/2
8 1/88
8 1/88
8 1/88
2431 1/8
2431 1/8
2431 1/8
24’-8”24’-8”24’-8”24’-8”24’-8”24’-8”
12’-1 1/8”12’-6 3/4”14’-2 1/8”14’-7 3/4”16’-2 1/8”16’-7 3/4”
555555
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-2000-23 (S or AL)-53-10AL-FS-2000-23-53-10
GLCSL-FS-2000-23 (S or AL)-53-10GLCS-FS-2000-23 (S or AL)-53-12
AL-FS-2000-23-53-12GLCSL-FS-2000-23 (S or AL)-53-12GLCS-FS-2000-23 (S or AL)-53-14
AL-FS-2000-23-53-14GLCSL-FS-2000-23 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
193019193019193019
16 1/817
16 1/816 1/8
1716 1/816 1/8
1716 1/8
19 5/825 1/4
2319 5/825 1/4
2319 5/825 1/4
23
24-
27 3/824-
27 3/824-
27 3/8
14 7/815 1/214 7/814 7/815 1/214 7/814 7/815 1/214 7/8
8 1/88
8 1/88 1/8
88 1/88 1/8
88 1/8
2431 1/8
2424
31 1/82424
31 1/824
24’-8”24’-8”24’-8”24’-8”24’-8”24’-8”24’-8”24’-8”24’-8”
12’-1 1/8”12’-6 3/4”12’-4 1/2”14’-2 1/8”14’-7 3/4”14’-5 1/2”16’-2 1/8”16’-7 3/4”16’-6 1/2”
555555555
443443443
63’
10’10’12’12’14’14’
GLCS-FS-2000-23 (S or AL)-63-10AL-FS-2000-23-63-10
GLCS-FS-2000-23 (S or AL)-63-12AL-FS-2000-23-63-12
GLCS-FS-2000-23 (S or AL)-63-14AL-FS-2000-23-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
263626362636
16 1/817
16 1/817
16 1/817
19 5/825 1/419 5/825 1/419 5/825 1/4
24-
24-
24-
14 7/815 1/214 7/815 1/214 7/815 1/2
8 1/88
8 1/88
8 1/88
2431 1/8
2431 1/8
2431 1/8
24’-8”24’-8”24’-8”24’-8”24’-8”24’-8”
12’-1 1/8”12’-6 3/4”14’-2 1/8”14’-7 3/4”16’-2 1/8”16’-7 3/4”
555555
444444
64’10’12’14’
GLCSLX-FS-2000-23 (S or AL)-64-10GLCSLX-FS-2000-23 (S or AL)-64-12GLCSLX-FS-2000-23 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
16 1/816 1/816 1/8
25 5/825 5/825 5/8
303030
14 7/814 7/814 7/8
8 1/88 1/88 1/8
31 1/831 1/831 1/8
24’-8”24’-8”24’-8”
12’-7 1/8”14’-8 1/8”16’-9 1/8”
555
333
78’10’12’14’
GLCSL-FS-2000-23 (S or AL)-78-10GLCSL-FS-2000-23 (S or AL)-78-12GLCSL-FS-2000-23 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
16 1/816 1/816 1/8
232323
27 3/827 3/827 3/8
14 7/814 7/814 7/8
8 1/88 1/88 1/8
31 1/831 1/831 1/8
24’-8”24’-8”24’-8”
12’-4 1/2”14’-5 1/2”16’-6 1/2”
555
444
83’
10’10’12’12’14’14’
GLCS-FS-2000-23 (S or AL)-83-10AL-FS-2000-23-83-10
GLCS-FS-2000-23 (S or AL)-83-12AL-FS-2000-23-83-12
GLCS-FS-2000-23 (S or AL)-83-14AL-FS-2000-23-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
16 1/817
16 1/817
16 1/817
19 5/825 1/419 5/825 1/419 5/825 1/4
24-
24-
24-
14 7/815 1/214 7/815 1/214 7/815 1/2
8 1/88
8 1/88
8 1/88
31 1/831 1/831 1/831 1/831 1/831 1/8
24’-8”24’-8”24’-8”24’-8”24’-8”24’-8”
12’-1 1/8”12’-6 3/4”14’-2 1/8”14’-7 3/4”16’-2 1/8”16’-7 3/4”
555555
555555
94’10’12’14’
GLCSLX-FS-2000-23 (S or AL)-94-10GLCSLX-FS-2000-23 (S or AL)-94-12GLCSLX-FS-2000-23 (S or AL)-94-14
SteelSteelSteel
30’30’30’
545454
16 1/816 1/816 1/8
25 5/825 5/825 5/8
303030
14 7/814 7/814 7/8
8 1/88 1/88 1/8
31 1/831 1/831 1/8
24’-8”24’-8”24’-8”
12’-7 1/8”14’-8 1/8”16’-9 1/8”
555
444
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-2000-23 (S or AL)-103-10AL-FS-2000-23-103-10
GLCSL-FS-2000-23 (S or AL)-103-10GLCS-FS-2000-23 (S or AL)-103-12
AL-FS-2000-23-103-12GLCSL-FS-2000-23 (S or AL)-103-12GLCS-FS-2000-23 (S or AL)-103-14
AL-FS-2000-23-103-14GLCSL-FS-2000-23 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
16 1/817
16 1/816 1/8
1716 1/816 1/8
1716 1/8
19 5/825 1/4
2319 5/825 1/4
2319 5/825 1/4
23
24-
27 3/824-
27 3/824-
27 3/8
14 7/815 1/214 7/814 7/815 1/214 7/814 7/815 1/214 7/8
8 1/88
8 1/88 1/8
88 1/88 1/8
88 1/8
31 1/831 1/831 1/831 1/831 1/831 1/831 1/831 1/831 1/8
24’-8”24’-8”24’-8”24’-8”24’-8”24’-8”24’-8”24’-8”24’-8”
12’-1 1/8”12’-6 3/4”12’-4 1/2”14’-2 1/8”14’-7 3/4”14’-5 1/2”16’-2 1/8”16’-7 3/4”16’-6 1/2”
555555555
665665665
124’10’12’14’
GLCSLX-FS-2000-23 (S or AL)-124-10GLCSLX-FS-2000-23 (S or AL)-124-12GLCSLX-FS-2000-23 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
16 1/816 1/816 1/8
25 5/825 5/825 5/8
303030
14 7/814 7/814 7/8
8 1/88 1/88 1/8
31 1/831 1/831 1/8
24’-8”24’-8”24’-8”
12’-7 1/8”14’-8 1/8”16’-9 1/8”
555
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
FREE STANDING WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
28’
23’
10’10’12’12’14’14’
GLCS-FS-2000-28 (S or AL)-23-10AL-FS-2000-28-23-10
GLCS-FS-2000-28 (S or AL)-23-12AL-FS-2000-28-23-12
GLCS-FS-2000-28 (S or AL)-23-14AL-FS-2000-28-23-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9139
139
13
25 7/821
25 7/821
25 7/821
2327 1/2
2327 1/2
2327 1/2
26-
26-
26-
18 1/417
18 1/417
18 1/417
8 1/88
8 1/88
8 1/88
34 1/237 7/834 1/237 7/834 1/237 7/8
29’-8”29’-8”29’-8”29’-8”29’-8”29’-8”
12’-5 1/2”12’-10”
14’-5 1/2”14’-10”
16’-6 1/2”16’-11”
555555
222222
28’10’12’14’
GLCSL-FS-2000-28 (S or AL)-28-10GLCSL-FS-2000-28 (S or AL)-28-12GLCSL-FS-2000-28 (S or AL)-28-14
SteelSteelSteel
25’25’25’
999
25 7/825 7/825 7/8
26 3/826 3/826 3/8
29 3/829 3/829 3/8
18 1/418 1/418 1/4
8 1/88 1/88 1/8
34 1/234 1/234 1/2
29’-8”29’-8”29’-8”
12’-8 7/8”14’-8 7/8”16’-9 7/8”
555
222
33’
10’10’12’12’14’14’
GLCS-FS-2000-28 (S or AL)-33-10AL-FS-2000-28-33-10
GLCS-FS-2000-28 (S or AL)-33-12AL-FS-2000-28-33-12
GLCS-FS-2000-28 (S or AL)-33-14AL-FS-2000-28-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9199
199
19
25 7/821
25 7/821
25 7/821
2327 1/2
2327 1/2
2327 1/2
26-
26-
26-
18 1/417
18 1/417
18 1/417
8 1/88
8 1/88
8 1/88
34 1/237 7/834 1/237 7/834 1/237 7/8
29’-8”29’-8”29’-8”29’-8”29’-8”29’-8”
12’-5 1/2”12’-10”
14’-5 1/2”14’-10”
16’-6 1/2”16’-11”
555555
333333
34’10’12’14’
GLCSLX-FS-2000-28 (S or AL)-34-10GLCSLX-FS-2000-28 (S or AL)-34-12GLCSLX-FS-2000-28 (S or AL)-34-14
SteelSteelSteel
30’30’30’
999
25 7/825 7/825 7/8
292929
323232
18 1/418 1/418 1/4
8 1/88 1/88 1/8
34 1/234 1/234 1/2
29’-8”29’-8”29’-8”
12’-11 1/2”14’-11 1/2”17’-0 1/2”
555
222
43’
10’10’12’12’14’14’
GLCS-FS-2000-28 (S or AL)-43-10AL-FS-2000-28-43-10
GLCS-FS-2000-28 (S or AL)-43-12AL-FS-2000-28-43-12
GLCS-FS-2000-28 (S or AL)-43-14AL-FS-2000-28-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
132613261326
25 7/821
25 7/821
25 7/821
2327 1/2
2327 1/2
2327 1/2
26-
26-
26-
18 1/417
18 1/417
18 1/417
8 1/88
8 1/88
8 1/88
34 1/237 7/834 1/237 7/834 1/237 7/8
29’-8”29’-8”29’-8”29’-8”29’-8”29’-8”
12’-5 1/2”12’-10”
14’-5 1/2”14’-10”
16’-6 1/2”16’-11”
555555
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-2000-28 (S or AL)-53-10AL-FS-2000-28-53-10
GLCSL-FS-2000-28 (S or AL)-53-10GLCS-FS-2000-28 (S or AL)-53-12
AL-FS-2000-28-53-12GLCSL-FS-2000-28 (S or AL)-53-12GLCS-FS-2000-28 (S or AL)-53-14
AL-FS-2000-28-53-14GLCSL-FS-2000-28 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
133013133013133013
25 7/821
25 7/825 7/8
2125 7/825 7/8
2125 7/8
2327 1/226 3/8
2327 1/226 3/8
2327 1/226 3/8
26-
29 3/826-
29 3/826-
29 3/8
18 1/417
18 1/418 1/4
1718 1/418 1/4
1718 1/4
8 1/88
8 1/88 1/8
88 1/88 1/8
88 1/8
34 1/237 7/834 1/234 1/237 7/834 1/234 1/237 7/834 1/2
29’-8”29’-8”29’-8”29’-8”29’-8”29’-8”29’-8”29’-8”29’-8”
12’-5 1/2”12’-10”
12’-8 7/8”14’-5 1/2”
14’-10”14’-8 7/8”16’-6 1/2”
16’-11”16’-9 7/8”
555555555
443443443
63’
10’10’12’12’14’14’
GLCS-FS-2000-28 (S or AL)-63-10AL-FS-2000-28-63-10
GLCS-FS-2000-28 (S or AL)-63-12AL-FS-2000-28-63-12
GLCS-FS-2000-28 (S or AL)-63-14AL-FS-2000-28-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
193619361936
25 7/821
25 7/821
25 7/821
2327 1/2
2327 1/2
2327 1/2
26-
26-
26-
18 1/417
18 1/417
18 1/417
8 1/88
8 1/88
8 1/88
34 1/237 7/834 1/237 7/834 1/237 7/8
29’-8”29’-8”29’-8”29’-8”29’-8”29’-8”
12’-5 1/2”12’-10”
14’-5 1/2”14’-10”
16’-6 1/2”16’-11”
555555
444444
64’10’12’14’
GLCSLX-FS-2000-28 (S or AL)-64-10GLCSLX-FS-2000-28 (S or AL)-64-12GLCSLX-FS-2000-28 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
25 7/825 7/825 7/8
292929
323232
18 1/418 1/418 1/4
8 1/88 1/88 1/8
37 7/837 7/837 7/8
29’-8”29’-8”29’-8”
12’-11 1/2”14’-11 1/2”17’-0 1/2”
555
333
78’10’12’14’
GLCSL-FS-2000-28 (S or AL)-78-10GLCSL-FS-2000-28 (S or AL)-78-12GLCSL-FS-2000-28 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
25 7/825 7/825 7/8
26 3/826 3/826 3/8
29 3/829 3/829 3/8
18 1/418 1/418 1/4
8 1/88 1/88 1/8
37 7/837 7/837 7/8
29’-8”29’-8”29’-8”
12’-8 7/8”14’-8 7/8”16’-9 7/8”
555
444
83’
10’10’12’12’14’14’
GLCS-FS-2000-28 (S or AL)-83-10AL-FS-2000-28-83-10
GLCS-FS-2000-28 (S or AL)-83-12AL-FS-2000-28-83-12
GLCS-FS-2000-28 (S or AL)-83-14AL-FS-2000-28-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
25 7/821
25 7/821
25 7/821
2327 1/2
2327 1/2
2327 1/2
26-
26-
26-
18 1/417
18 1/417
18 1/417
8 1/88
8 1/88
8 1/88
37 7/837 7/837 7/837 7/837 7/837 7/8
29’-8”29’-8”29’-8”29’-8”29’-8”29’-8”
12’-5 1/2”12’-10”
14’-5 1/2”14’-10”
16’-6 1/2”16’-11”
555555
555555
94’10’12’14’
GLCSLX-FS-2000-28 (S or AL)-94-10GLCSLX-FS-2000-28 (S or AL)-94-12GLCSLX-FS-2000-28 (S or AL)-94-14
SteelSteelSteel
30’30’30’
545454
25 7/825 7/825 7/8
292929
323232
18 1/418 1/418 1/4
8 1/88 1/88 1/8
37 7/837 7/837 7/8
29’-8”29’-8”29’-8”
12’-11 1/2”14’-11 1/2”17’-0 1/2”
555
444
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-2000-28 (S or AL)-103-10AL-FS-2000-28-103-10
GLCSL-FS-2000-28 (S or AL)-103-10GLCS-FS-2000-28 (S or AL)-103-12
AL-FS-2000-28-103-12GLCSL-FS-2000-28 (S or AL)-103-12GLCS-FS-2000-28 (S or AL)-103-14
AL-FS-2000-28-103-14GLCSL-FS-2000-28 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
25 7/821
25 7/825 7/8
2125 7/825 7/8
2125 7/8
2327 1/226 3/8
2327 1/226 3/8
2327 1/226 3/8
26-
29 3/826-
29 3/826-
29 3/8
18 1/417
18 1/418 1/4
1718 1/418 1/4
1718 1/4
8 1/88
8 1/88 1/8
88 1/88 1/8
88 1/8
37 7/837 7/837 7/837 7/837 7/837 7/837 7/837 7/837 7/8
29’-8”29’-8”29’-8”29’-8”29’-8”29’-8”29’-8”29’-8”29’-8”
12’-5 1/2”12’-10”
12’-8 7/8”14’-5 1/2”
14’-10”14’-8 7/8”16’-6 1/2”
16’-11”16’-9 7/8”
555555555
665665665
124’10’12’14’
GLCSLX-FS-2000-28 (S or AL)-124-10GLCSLX-FS-2000-28 (S or AL)-124-12GLCSLX-FS-2000-28 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
25 7/825 7/825 7/8
292929
323232
18 1/418 1/418 1/4
8 1/88 1/88 1/8
37 7/837 7/837 7/8
29’-8”29’-8”29’-8”
12’-11 1/2”14’-11 1/2”17’-0 1/2”
555
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
2000# CAPACITYFR
EE S
TAN
DIN
G W
OR
KST
ATIO
N C
RA
NES
27
FREE STA
ND
ING
WO
RK
STATION
CR
AN
ES
28
2000# CAPACITYFREE STANDING WORK STATION BRIDGE CRANES
BRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
34’
28’10’12’14’
GLCSL-FS-2000-34 (S or AL)-28-10GLCSL-FS-2000-34 (S or AL)-28-12GLCSL-FS-2000-34 (S or AL)-28-14
SteelSteelSteel
25’25’25’
131313
25 7/825 7/825 7/8
26 3/826 3/826 3/8
29 3/829 3/829 3/8
20 7/820 7/820 7/8
8 1/88 1/88 1/8
40 1/240 1/240 1/2
35’-8”35’-8”35’-8”
12’-9 7/8”14’-9 7/8”
16’-11 7/8”
555
222
33’
10’10’12’12’14’14’
GLCS-FS-2000-34 (S or AL)-33-10AL-FS-2000-34-33-10
GLCS-FS-2000-34 (S or AL)-33-12AL-FS-2000-34-33-12
GLCS-FS-2000-34 (S or AL)-33-14AL-FS-2000-34-33-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
9199
199
19
25 7/821
25 7/821
25 7/821
2527 1/2
2527 1/2
2527 1/2
26-
26-
26-
20 7/817 7/820 7/817 7/820 7/817 7/8
8 1/88
8 1/88
8 1/88
40 1/244 5/840 1/244 5/840 1/244 5/8
35’-8”35’-8”35’-8”35’-8”35’-8”35’-8”
12’-8 1/2”12’-11”
14’-8 1/2”14’-11”
16’-8 1/2”16’-11”
555555
333333
34’10’12’14’
GLCSLX-FS-2000-34 (S or AL)-34-10GLCSLX-FS-2000-34 (S or AL)-34-12GLCSLX-FS-2000-34 (S or AL)-34-14
SteelSteelSteel
30’30’30’
999
25 7/825 7/825 7/8
292929
323232
20 7/820 7/820 7/8
8 1/88 1/88 1/8
40 1/240 1/240 1/2
35’-8”35’-8”35’-8”
13’-2 1/2”15’-2 1/2”17’-2 1/2”
555
222
43’
10’10’12’12’14’14’
GLCS-FS-2000-34 (S or AL)-43-10AL-FS-2000-34-43-10
GLCS-FS-2000-34 (S or AL)-43-12AL-FS-2000-34-43-12
GLCS-FS-2000-34 (S or AL)-43-14AL-FS-2000-34-43-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
132613261326
25 7/821
25 7/821
25 7/821
2527 1/2
2527 1/2
2527 1/2
26-
26-
26-
20 7/817 7/820 7/817 7/820 7/817 7/8
8 1/88
8 1/88
8 1/88
40 1/244 5/840 1/244 5/840 1/244 5/8
35’-8”35’-8”35’-8”35’-8”35’-8”35’-8”
12’-8 1/2”12’-11”
14’-8 1/2”14’-11”
16’-8 1/2”16’-11”
555555
333333
53’
10’10’10’12’12’12’14’14’14’
GLCS-FS-2000-34 (S or AL)-53-10AL-FS-2000-34-53-10
GLCSL-FS-2000-34 (S or AL)-53-10GLCS-FS-2000-34 (S or AL)-53-12
AL-FS-2000-34-53-12GLCSL-FS-2000-34 (S or AL)-53-12GLCS-FS-2000-34 (S or AL)-53-14
AL-FS-2000-34-53-14GLCSL-FS-2000-34 (S or AL)-53-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
133013133013133013
25 7/821
25 7/825 7/8
2125 7/825 7/8
2125 7/8
2527 1/226 3/8
2527 1/226 3/8
2527 1/226 3/8
26-
29 3/826-
29 3/826-
29 3/8
20 7/817 7/820 7/820 7/817 7/820 7/820 7/817 7/820 7/8
8 1/88
8 1/88 1/8
88 1/88 1/8
88 1/8
40 1/244 5/840 1/240 1/244 5/840 1/240 1/244 5/840 1/2
35’-8”35’-8”35’-8”35’-8”35’-8”35’-8”35’-8”35’-8”35’-8”
12’-8 1/2”12’-11”
12’-9 7/8”14’-8 1/2”
14’-11”14’-9 7/8”16’-8 1/2”
16’-11”16’-11 7/8”
555555555
443443443
63’
10’10’12’12’14’14’
GLCS-FS-2000-34 (S or AL)-63-10AL-FS-2000-34-63-10
GLCS-FS-2000-34 (S or AL)-63-12AL-FS-2000-34-63-12
GLCS-FS-2000-34 (S or AL)-63-14AL-FS-2000-34-63-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
193619361936
25 7/821
25 7/821
25 7/821
2527 1/2
2527 1/2
2527 1/2
26-
26-
26-
20 7/817 7/820 7/817 7/820 7/817 7/8
8 1/88
8 1/88
8 1/88
40 1/244 5/840 1/244 5/840 1/244 5/8
35’-8”35’-8”35’-8”35’-8”35’-8”35’-8”
12’-8 1/2”12’-11”
14’-8 1/2”14’-11”
16’-8 1/2”16’-11”
555555
444444
64’10’12’14’
GLCSLX-FS-2000-34 (S or AL)-64-10GLCSLX-FS-2000-34 (S or AL)-64-12GLCSLX-FS-2000-34 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
25 7/825 7/825 7/8
292929
323232
20 7/820 7/820 7/8
8 1/88 1/88 1/8
44 5/844 5/844 5/8
35’-8”35’-8”35’-8”
13’-2 1/2”15’-2 1/2”17’-2 1/2”
555
333
78’10’12’14’
GLCSL-FS-2000-34 (S or AL)-78-10GLCSL-FS-2000-34 (S or AL)-78-12GLCSL-FS-2000-34 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
25 7/825 7/825 7/8
26 3/826 3/826 3/8
29 3/829 3/829 3/8
20 7/820 7/820 7/8
8 1/88 1/88 1/8
44 5/844 5/844 5/8
35’-8”35’-8”35’-8”
12’-9 7/8”14’-9 7/8”
16’-11 7/8”
555
444
83’
10’10’12’12’14’14’
GLCS-FS-2000-34 (S or AL)-83-10AL-FS-2000-34-83-10
GLCS-FS-2000-34 (S or AL)-83-12AL-FS-2000-34-83-12
GLCS-FS-2000-34 (S or AL)-83-14AL-FS-2000-34-83-14
SteelAlumSteelAlumSteelAlum
20’20’20’20’20’20’
464646464646
25 7/821
25 7/821
25 7/821
2527 1/2
2527 1/2
2527 1/2
26-
26-
26-
20 7/817 7/820 7/817 7/820 7/817 7/8
8 1/88
8 1/88
8 1/88
44 5/844 5/844 5/844 5/844 5/844 5/8
35’-8”35’-8”35’-8”35’-8”35’-8”35’-8”
12’-8 1/2”12’-11”
14’-8 1/2”14’-11”
16’-8 1/2”16’-11”
555555
555555
94’10’12’14’
GLCSLX-FS-2000-34 (S or AL)-94-10GLCSLX-FS-2000-34 (S or AL)-94-12GLCSLX-FS-2000-34 (S or AL)-94-14
SteelSteelSteel
30’30’30’
545454
25 7/825 7/825 7/8
292929
323232
20 7/820 7/820 7/8
8 1/88 1/88 1/8
44 5/844 5/844 5/8
35’-8”35’-8”35’-8”
13’-2 1/2”15’-2 1/2”17’-2 1/2”
555
444
103’
10’10’10’12’12’12’14’14’14’
GLCS-FS-2000-34 (S or AL)-103-10AL-FS-2000-34-103-10
GLCSL-FS-2000-34 (S or AL)-103-10GLCS-FS-2000-34 (S or AL)-103-12
AL-FS-2000-34-103-12GLCSL-FS-2000-34 (S or AL)-103-12GLCS-FS-2000-34 (S or AL)-103-14
AL-FS-2000-34-103-14GLCSL-FS-2000-34 (S or AL)-103-14
SteelAlumSteelSteelAlumSteelSteelAlumSteel
20’20’25’20’20’25’20’20’25’
545454545454545454
25 7/821
25 7/825 7/8
2125 7/825 7/8
2125 7/8
2527 1/226 3/8
2527 1/226 3/8
2527 1/226 3/8
26-
29 3/826-
29 3/826-
29 3/8
20 7/817 7/820 7/820 7/817 7/820 7/820 7/817 7/820 7/8
8 1/88
8 1/88 1/8
88 1/88 1/8
88 1/8
44 5/844 5/844 5/844 5/844 5/844 5/844 5/844 5/844 5/8
35’-8”35’-8”35’-8”35’-8”35’-8”35’-8”35’-8”35’-8”35’-8”
12’-8 1/2”12’-11”
12’-9 7/8”14’-8 1/2”
14’-11”14’-9 7/8”16’-8 1/2”
16’-11”16’-11 7/8”
555555555
665665665
124’10’12’14’
GLCSLX-FS-2000-34 (S or AL)-124-10GLCSLX-FS-2000-34 (S or AL)-124-12GLCSLX-FS-2000-34 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
25 7/825 7/825 7/8
292929
323232
20 7/820 7/820 7/8
8 1/88 1/88 1/8
44 5/844 5/844 5/8
35’-8”35’-8”35’-8”
13’-2 1/2”15’-2 1/2”17’-2 1/2”
555
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
FREE STANDING WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
15’
23’10’12’14’
GLCS-FS-4000-15 (S or AL)-23-10GLCS-FS-4000-15 (S or AL)-23-12GLCS-FS-4000-15 (S or AL)-23-14
SteelSteelSteel
20’20’20’
999
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
17’-0”17’-0”17’-0”
12’-11 7/8”14’-11 7/8”16’-11 7/8”
777
222
28’10’12’14’
GLCSL-FS-4000-15 (S or AL)-28-10GLCSL-FS-4000-15 (S or AL)-28-12GLCSL-FS-4000-15 (S or AL)-28-14
SteelSteelSteel
25’25’25’
111111
25 7/825 7/825 7/8
31 3/831 3/831 3/8
34 1/234 1/234 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
17’-0”17’-0”17’-0”
13’-1 7/8”15’-1 7/8”17’-1 7/8”
777
222
33’10’12’14’
GLCS-FS-4000-15 (S or AL)-33-10GLCS-FS-4000-15 (S or AL)-33-12GLCS-FS-4000-15 (S or AL)-33-14
SteelSteelSteel
20’20’20’
131313
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
17’-0”17’-0”17’-0”
12’-11 7/8”14’-11 7/8”16’-11 7/8”
777
333
34’10’12’14’
GLCSLX-FS-4000-15 (S or AL)-34-10GLCSLX-FS-4000-15 (S or AL)-34-12GLCSLX-FS-4000-15 (S or AL)-34-14
SteelSteelSteel
30’30’30’
131313
25 7/825 7/825 7/8
33 3/833 3/833 3/8
36 1/236 1/236 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
17’-0”17’-0”17’-0”
13’-3 7/8”15’-3 7/8”17’-3 7/8”
777
222
43’10’12’14’
GLCS-FS-4000-15 (S or AL)-43-10GLCS-FS-4000-15 (S or AL)-43-12GLCS-FS-4000-15 (S or AL)-43-14
SteelSteelSteel
20’20’20’
171717
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
17’-0”17’-0”17’-0”
12’-11 7/8”14’-11 7/8”16’-11 7/8”
777
333
53’
10’10’12’12’14’14’
GLCS-FS-4000-15 (S or AL)-53-10GLCSL-FS-4000-15 (S or AL)-53-10GLCS-FS-4000-15 (S or AL)-53-12
GLCSL-FS-4000-15 (S or AL)-53-12GLCS-FS-4000-15 (S or AL)-53-14
GLCSL-FS-4000-15 (S or AL)-53-14
SteelSteelSteelSteelSteelSteel
20’25’20’25’20’25’
191919191919
25 7/825 7/825 7/825 7/825 7/825 7/8
29 3/831 3/829 3/831 3/829 3/831 3/8
32 1/234 1/232 1/234 1/232 1/234 1/2
21 3/821 3/821 3/821 3/821 3/821 3/8
15 1/815 1/815 1/815 1/815 1/815 1/8
38 1/238 1/238 1/238 1/238 1/238 1/2
17’-0”17’-0”17’-0”17’-0”17’-0”17’-0”
12’-11 7/8”13’-1 7/8”
14’-11 7/8”15’-1 7/8”
16’-11 7/8”17’-1 7/8”
777777
434343
63’10’12’14’
GLCS-FS-4000-15 (S or AL)-63-10GLCS-FS-4000-15 (S or AL)-63-12GLCS-FS-4000-15 (S or AL)-63-14
SteelSteelSteel
20’20’20’
232323
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
17’-0”17’-0”17’-0”
12’-11 7/8”14’-11 7/8”16’-11 7/8”
777
444
64’10’12’14’
GLCSLX-FS-4000-15 (S or AL)-64-10GLCSLX-FS-4000-15 (S or AL)-64-12GLCSLX-FS-4000-15 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
25 7/825 7/825 7/8
33 3/833 3/833 3/8
36 1/236 1/236 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
17’-0”17’-0”17’-0”
13’-3 7/8”15’-3 7/8”17’-3 7/8”
777
333
78’10’12’14’
GLCSL-FS-4000-15 (S or AL)-78-10GLCSL-FS-4000-15 (S or AL)-78-12GLCSL-FS-4000-15 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
25 7/825 7/825 7/8
31 3/831 3/831 3/8
34 1/234 1/234 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
17’-0”17’-0”17’-0”
13’-1 7/8”15’-1 7/8”17’-1 7/8”
777
444
83’10’12’14’
GLCS-FS-4000-15 (S or AL)-83-10GLCS-FS-4000-15 (S or AL)-83-12GLCS-FS-4000-15 (S or AL)-83-14
SteelSteelSteel
20’20’20’
464646
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
17’-0”17’-0”17’-0”
12’-11 7/8”14’-11 7/8”16’-11 7/8”
777
555
94’10’12’14’
GLCSLX-FS-4000-15 (S or AL)-94-10GLCSLX-FS-4000-15 (S or AL)-94-12GLCSLX-FS-4000-15 (S or AL)-94-14
SteelSteelSteel
30’30’30’
535353
25 7/825 7/825 7/8
33 3/833 3/833 3/8
36 1/236 1/236 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
17’-0”17’-0”17’-0”
13’-3 7/8”15’-3 7/8”17’-3 7/8”
777
444
103’
10’10’12’12’14’14’
GLCS-FS-4000-15 (S or AL)-103-10GLCSL-FS-4000-15 (S or AL)-103-10GLCS-FS-4000-15 (S or AL)-103-12
GLCSL-FS-4000-15 (S or AL)-103-12GLCS-FS-4000-15 (S or AL)-103-14
GLCSL-FS-4000-15 (S or AL)-103-14
SteelSteelSteelSteelSteelSteel
20’25’20’25’20’25’
545454545454
25 7/825 7/825 7/825 7/825 7/825 7/8
29 3/831 3/829 3/831 3/829 3/831 3/8
32 1/234 1/232 1/234 1/232 1/234 1/2
21 3/821 3/821 3/821 3/821 3/821 3/8
15 1/815 1/815 1/815 1/815 1/815 1/8
38 1/238 1/238 1/238 1/238 1/238 1/2
17’-0”17’-0”17’-0”17’-0”17’-0”17’-0”
12’-11 7/8”13’-1 7/8”
14’-11 7/8”15’-1 7/8”
16’-11 7/8”17’-1 7/8”
777777
656565
124’10’12’14’
GLCSLX-FS-4000-15 (S or AL)-124-10GLCSLX-FS-4000-15 (S or AL)-124-12GLCSLX-FS-4000-15 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
25 7/825 7/825 7/8
33 3/833 3/833 3/8
36 1/236 1/236 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
17’-0”17’-0”17’-0”
13’-3 7/8”15’-3 7/8”17’-3 7/8”
777
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
4000# CAPACITYFR
EE S
TAN
DIN
G W
OR
KST
ATIO
N C
RA
NES
29
FREE STA
ND
ING
WO
RK
STATION
CR
AN
ES
30
4000# CAPACITYFREE STANDING WORK STATION BRIDGE CRANES
BRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
20’
23’10’12’14’
GLCS-FS-4000-20 (S or AL)-23-10GLCS-FS-4000-20 (S or AL)-23-12GLCS-FS-4000-20 (S or AL)-23-14
SteelSteelSteel
20’20’20’
999
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
22’-0”22’-0”22’-0”
12’-11 7/8”14’-11 7/8”16’-11 7/8”
777
222
28’10’12’14’
GLCSL-FS-4000-20 (S or AL)-28-10GLCSL-FS-4000-20 (S or AL)-28-12GLCSL-FS-4000-20 (S or AL)-28-14
SteelSteelSteel
25’25’25’
111111
25 7/825 7/825 7/8
31 3/831 3/831 3/8
34 1/234 1/234 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
22’-0”22’-0”22’-0”
13’-1 7/8”15’-1 7/8”17’-1 7/8”
777
222
33’10’12’14’
GLCS-FS-4000-20 (S or AL)-33-10GLCS-FS-4000-20 (S or AL)-33-12GLCS-FS-4000-20 (S or AL)-33-14
SteelSteelSteel
20’20’20’
131313
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
22’-0”22’-0”22’-0”
12’-11 7/8”14’-11 7/8”16’-11 7/8”
777
333
34’10’12’14’
GLCSLX-FS-4000-20 (S or AL)-34-10GLCSLX-FS-4000-20 (S or AL)-34-12GLCSLX-FS-4000-20 (S or AL)-34-14
SteelSteelSteel
30’30’30’
131313
25 7/825 7/825 7/8
33 3/833 3/833 3/8
36 1/236 1/236 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
22’-0”22’-0”22’-0”
13’-3 7/8”15’-3 7/8”17’-3 7/8”
777
222
43’10’12’14’
GLCS-FS-4000-20 (S or AL)-43-10GLCS-FS-4000-20 (S or AL)-43-12GLCS-FS-4000-20 (S or AL)-43-14
SteelSteelSteel
20’20’20’
171717
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
22’-0”22’-0”22’-0”
12’-11 7/8”14’-11 7/8”16’-11 7/8”
777
333
53’
10’10’12’12’14’14’
GLCS-FS-4000-20 (S or AL)-53-10GLCSL-FS-4000-20 (S or AL)-53-10GLCS-FS-4000-20 (S or AL)-53-12
GLCSL-FS-4000-20 (S or AL)-53-12GLCS-FS-4000-20 (S or AL)-53-14
GLCSL-FS-4000-20 (S or AL)-53-14
SteelSteelSteelSteelSteelSteel
20’25’20’25’20’25’
191919191919
25 7/825 7/825 7/825 7/825 7/825 7/8
29 3/831 3/829 3/831 3/829 3/831 3/8
32 1/234 1/232 1/234 1/232 1/234 1/2
21 3/821 3/821 3/821 3/821 3/821 3/8
15 1/815 1/815 1/815 1/815 1/815 1/8
38 1/238 1/238 1/238 1/238 1/238 1/2
22’-0”22’-0”22’-0”22’-0”22’-0”22’-0”
12’-11 7/8”13’-1 7/8”
14’-11 7/8”15’-1 7/8”
16’-11 7/8”17’-1 7/8”
777777
434343
63’10’12’14’
GLCS-FS-4000-20 (S or AL)-63-10GLCS-FS-4000-20 (S or AL)-63-12GLCS-FS-4000-20 (S or AL)-63-14
SteelSteelSteel
20’20’20’
232323
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
22’-0”22’-0”22’-0”
12’-11 7/8”14’-11 7/8”16’-11 7/8”
777
444
64’10’12’14’
GLCSLX-FS-4000-20 (S or AL)-64-10GLCSLX-FS-4000-20 (S or AL)-64-12GLCSLX-FS-4000-20 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
25 7/825 7/825 7/8
33 3/833 3/833 3/8
36 1/236 1/236 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
22’-0”22’-0”22’-0”
13’-3 7/8”15’-3 7/8”17’-3 7/8”
777
333
78’10’12’14’
GLCSL-FS-4000-20 (S or AL)-78-10GLCSL-FS-4000-20 (S or AL)-78-12GLCSL-FS-4000-20 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
25 7/825 7/825 7/8
31 3/831 3/831 3/8
34 1/234 1/234 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
22’-0”22’-0”22’-0”
13’-1 7/8”15’-1 7/8”17’-1 7/8”
777
444
83’10’12’14’
GLCS-FS-4000-20 (S or AL)-83-10GLCS-FS-4000-20 (S or AL)-83-12GLCS-FS-4000-20 (S or AL)-83-14
SteelSteelSteel
20’20’20’
464646
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
22’-0”22’-0”22’-0”
12’-11 7/8”14’-11 7/8”16’-11 7/8”
777
555
94’10’12’14’
GLCSLX-FS-4000-20 (S or AL)-94-10GLCSLX-FS-4000-20 (S or AL)-94-12GLCSLX-FS-4000-20 (S or AL)-94-14
SteelSteelSteel
30’30’30’
535353
25 7/825 7/825 7/8
33 3/833 3/833 3/8
36 1/236 1/236 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
22’-0”22’-0”22’-0”
13’-3 7/8”15’-3 7/8”17’-3 7/8”
777
444
103’
10’10’12’12’14’14’
GLCS-FS-4000-20 (S or AL)-103-10GLCSL-FS-4000-20 (S or AL)-103-10GLCS-FS-4000-20 (S or AL)-103-12
GLCSL-FS-4000-20 (S or AL)-103-12GLCS-FS-4000-20 (S or AL)-103-14
GLCSL-FS-4000-20 (S or AL)-103-14
SteelSteelSteelSteelSteelSteel
20’25’20’25’20’25’
545454545454
25 7/825 7/825 7/825 7/825 7/825 7/8
29 3/831 3/829 3/831 3/829 3/831 3/8
32 1/234 1/232 1/234 1/232 1/234 1/2
21 3/821 3/821 3/821 3/821 3/821 3/8
15 1/815 1/815 1/815 1/815 1/815 1/8
38 1/238 1/238 1/238 1/238 1/238 1/2
22’-0”22’-0”22’-0”22’-0”22’-0”22’-0”
12’-11 7/8”13’-1 7/8”
14’-11 7/8”15’-1 7/8”
16’-11 7/8”17’-1 7/8”
777777
656565
124’10’12’14’
GLCSLX-FS-4000-20 (S or AL)-124-10GLCSLX-FS-4000-20 (S or AL)-124-12GLCSLX-FS-4000-20 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
25 7/825 7/825 7/8
33 3/833 3/833 3/8
36 1/236 1/236 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
22’-0”22’-0”22’-0”
13’-3 7/8”15’-3 7/8”17’-3 7/8”
777
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
FREE STANDING WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
23’
23’10’12’14’
GLCS-FS-4000-23 (S or AL)-23-10GLCS-FS-4000-23 (S or AL)-23-12GLCS-FS-4000-23 (S or AL)-23-14
SteelSteelSteel
20’20’20’
999
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
30’-0”30’-0”30’-0”
12’-11 7/8”14’-11 7/8”16’-11 7/8”
777
222
28’10’12’14’
GLCSL-FS-4000-23 (S or AL)-28-10GLCSL-FS-4000-23 (S or AL)-28-12GLCSL-FS-4000-23 (S or AL)-28-14
SteelSteelSteel
25’25’25’
131313
25 7/825 7/825 7/8
31 3/831 3/831 3/8
34 1/234 1/234 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
30’-0”30’-0”30’-0”
13’-1 7/8”15’-1 7/8”17’-1 7/8”
777
222
33’10’12’14’
GLCS-FS-4000-23 (S or AL)-33-10GLCS-FS-4000-23 (S or AL)-33-12GLCS-FS-4000-23 (S or AL)-33-14
SteelSteelSteel
20’20’20’
131313
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
30’-0”30’-0”30’-0”
12’-11 7/8”14’-11 7/8”16’-11 7/8”
777
333
34’10’12’14’
GLCSLX-FS-4000-23 (S or AL)-34-10GLCSLX-FS-4000-23 (S or AL)-34-12GLCSLX-FS-4000-23 (S or AL)-34-14
SteelSteelSteel
30’30’30’
131313
25 7/825 7/825 7/8
33 3/833 3/833 3/8
36 1/236 1/236 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
30’-0”30’-0”30’-0”
13’-3 7/8”15’-3 7/8”17’-3 7/8”
777
222
43’10’12’14’
GLCS-FS-4000-23 (S or AL)-43-10GLCS-FS-4000-23 (S or AL)-43-12GLCS-FS-4000-23 (S or AL)-43-14
SteelSteelSteel
20’20’20’
191919
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
30’-0”30’-0”30’-0”
12’-11 7/8”14’-11 7/8”16’-11 7/8”
777
333
53’
10’10’12’12’14’14’
GLCS-FS-4000-23 (S or AL)-53-10GLCSL-FS-4000-23 (S or AL)-53-10GLCS-FS-4000-23 (S or AL)-53-12
GLCSL-FS-4000-23 (S or AL)-53-12GLCS-FS-4000-23 (S or AL)-53-14
GLCSL-FS-4000-23 (S or AL)-53-14
SteelSteelSteelSteelSteelSteel
20’25’20’25’20’25’
191919191919
25 7/825 7/825 7/825 7/825 7/825 7/8
29 3/831 3/829 3/831 3/829 3/831 3/8
32 1/234 1/232 1/234 1/232 1/234 1/2
21 3/821 3/821 3/821 3/821 3/821 3/8
15 1/815 1/815 1/815 1/815 1/815 1/8
38 1/238 1/238 1/238 1/238 1/238 1/2
30’-0”30’-0”30’-0”30’-0”30’-0”30’-0”
12’-11 7/8”13’-1 7/8”
14’-11 7/8”15’-1 7/8”
16’-11 7/8”17’-1 7/8”
777777
434343
63’10’12’14’
GLCS-FS-4000-23 (S or AL)-63-10GLCS-FS-4000-23 (S or AL)-63-12GLCS-FS-4000-23 (S or AL)-63-14
SteelSteelSteel
20’20’20’
262626
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
30’-0”30’-0”30’-0”
12’-11 7/8”14’-11 7/8”16’-11 7/8”
777
444
64’10’12’14’
GLCSLX-FS-4000-23 (S or AL)-64-10GLCSLX-FS-4000-23 (S or AL)-64-12GLCSLX-FS-4000-23 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
25 7/825 7/825 7/8
33 3/833 3/833 3/8
36 1/236 1/236 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
30’-0”30’-0”30’-0”
13’-3 7/8”15’-3 7/8”17’-3 7/8”
777
333
78’10’12’14’
GLCSL-FS-4000-23 (S or AL)-78-10GLCSL-FS-4000-23 (S or AL)-78-12GLCSL-FS-4000-23 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
25 7/825 7/825 7/8
31 3/831 3/831 3/8
34 1/234 1/234 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
30’-0”30’-0”30’-0”
13’-1 7/8”15’-1 7/8”17’-1 7/8”
777
444
83’10’12’14’
GLCS-FS-4000-23 (S or AL)-83-10GLCS-FS-4000-23 (S or AL)-83-12GLCS-FS-4000-23 (S or AL)-83-14
SteelSteelSteel
20’20’20’
464646
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
30’-0”30’-0”30’-0”
12’-11 7/8”14’-11 7/8”16’-11 7/8”
777
555
94’10’12’14’
GLCSLX-FS-4000-23 (S or AL)-94-10GLCSLX-FS-4000-23 (S or AL)-94-12GLCSLX-FS-4000-23 (S or AL)-94-14
SteelSteelSteel
30’30’30’
545454
25 7/825 7/825 7/8
33 3/833 3/833 3/8
36 1/236 1/236 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
30’-0”30’-0”30’-0”
13’-3 7/8”15’-3 7/8”17’-3 7/8”
777
444
103’
10’10’12’12’14’14’
GLCS-FS-4000-23 (S or AL)-103-10GLCSL-FS-4000-23 (S or AL)-103-10GLCS-FS-4000-23 (S or AL)-103-12
GLCSL-FS-4000-23 (S or AL)-103-12GLCS-FS-4000-23 (S or AL)-103-14
GLCSL-FS-4000-23 (S or AL)-103-14
SteelSteelSteelSteelSteelSteel
20’25’20’25’20’25’
545454545454
25 7/825 7/825 7/825 7/825 7/825 7/8
29 3/831 3/829 3/831 3/829 3/831 3/8
32 1/234 1/232 1/234 1/232 1/234 1/2
21 3/821 3/821 3/821 3/821 3/821 3/8
15 1/815 1/815 1/815 1/815 1/815 1/8
38 1/238 1/238 1/238 1/238 1/238 1/2
30’-0”30’-0”30’-0”30’-0”30’-0”30’-0”
12’-11 7/8”13’-1 7/8”
14’-11 7/8”15’-1 7/8”
16’-11 7/8”17’-1 7/8”
777777
656565
124’10’12’14’
GLCSLX-FS-4000-23 (S or AL)-124-10GLCSLX-FS-4000-23 (S or AL)-124-12GLCSLX-FS-4000-23 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
25 7/825 7/825 7/8
33 3/833 3/833 3/8
36 1/236 1/236 1/2
21 3/821 3/821 3/8
15 1/815 1/815 1/8
38 1/238 1/238 1/2
30’-0”30’-0”30’-0”
13’-3 7/8”15’-3 7/8”17’-3 7/8”
777
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
4000# CAPACITYFR
EE S
TAN
DIN
G W
OR
KST
ATIO
N C
RA
NES
31
FREE STA
ND
ING
WO
RK
STATION
CR
AN
ES
32
4000# CAPACITYFREE STANDING WORK STATION BRIDGE CRANES
BRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
28’
23’10’12’14’
GLCS-FS-4000-28 (S or AL)-23-10GLCS-FS-4000-28 (S or AL)-23-12GLCS-FS-4000-28 (S or AL)-23-14
SteelSteelSteel
20’20’20’
999
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
23 3/823 3/823 3/8
15 1/815 1/815 1/8
41 1/241 1/241 1/2
36’-0”36’-0”36’-0”
13’-0 7/8”15’-0 7/8”17’-0 7/8”
777
222
28’10’12’14’
GLCSL-FS-4000-28 (S or AL)-28-10GLCSL-FS-4000-28 (S or AL)-28-12GLCSL-FS-4000-28 (S or AL)-28-14
SteelSteelSteel
25’25’25’
999
25 7/825 7/825 7/8
31 3/831 3/831 3/8
34 1/234 1/234 1/2
23 3/823 3/823 3/8
15 1/815 1/815 1/8
41 1/241 1/241 1/2
36’-0”36’-0”36’-0”
13’-2 7/8”15’-2 7/8”17’-2 7/8”
777
222
33’10’12’14’
GLCS-FS-4000-28 (S or AL)-33-10GLCS-FS-4000-28 (S or AL)-33-12GLCS-FS-4000-28 (S or AL)-33-14
SteelSteelSteel
20’20’20’
999
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
23 3/823 3/823 3/8
15 1/815 1/815 1/8
41 1/241 1/241 1/2
36’-0”36’-0”36’-0”
13’-0 7/8”15’-0 7/8”17’-0 7/8”
777
333
34’10’12’14’
GLCSLX-FS-4000-28 (S or AL)-34-10GLCSLX-FS-4000-28 (S or AL)-34-12GLCSLX-FS-4000-28 (S or AL)-34-14
SteelSteelSteel
30’30’30’
999
25 7/825 7/825 7/8
33 3/833 3/833 3/8
36 1/236 1/236 1/2
23 3/823 3/823 3/8
15 1/815 1/815 1/8
41 1/241 1/241 1/2
36’-0”36’-0”36’-0”
13’-4 7/8”15’-4 7/8”17’-4 7/8”
777
222
43’10’12’14’
GLCS-FS-4000-28 (S or AL)-43-10GLCS-FS-4000-28 (S or AL)-43-12GLCS-FS-4000-28 (S or AL)-43-14
SteelSteelSteel
20’20’20’
131313
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
23 3/823 3/823 3/8
15 1/815 1/815 1/8
41 1/241 1/241 1/2
36’-0”36’-0”36’-0”
13’-0 7/8”15’-0 7/8”17’-0 7/8”
777
333
53’
10’10’12’12’14’14’
GLCS-FS-4000-28 (S or AL)-53-10GLCSL-FS-4000-28 (S or AL)-53-10GLCS-FS-4000-28 (S or AL)-53-12
GLCSL-FS-4000-28 (S or AL)-53-12GLCS-FS-4000-28 (S or AL)-53-14
GLCSL-FS-4000-28 (S or AL)-53-14
SteelSteelSteelSteelSteelSteel
20’25’20’25’20’25’
131313131313
25 7/825 7/825 7/825 7/825 7/825 7/8
29 3/831 3/829 3/831 3/829 3/831 3/8
32 1/234 1/232 1/234 1/232 1/234 1/2
23 3/823 3/823 3/823 3/823 3/823 3/8
15 1/815 1/815 1/815 1/815 1/815 1/8
41 1/241 1/241 1/241 1/241 1/241 1/2
36’-0”36’-0”36’-0”36’-0”36’-0”36’-0”
13’-0 7/8”13’-2 7/8”15’-0 7/8”15’-2 7/8”17’-0 7/8”17’-2 7/8”
777777
434343
63’10’12’14’
GLCS-FS-4000-28 (S or AL)-63-10GLCS-FS-4000-28 (S or AL)-63-12GLCS-FS-4000-28 (S or AL)-63-14
SteelSteelSteel
20’20’20’
191919
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
23 3/823 3/823 3/8
15 1/815 1/815 1/8
41 1/241 1/241 1/2
36’-0”36’-0”36’-0”
13’-0 7/8”15’-0 7/8”17’-0 7/8”
777
444
64’10’12’14’
GLCSLX-FS-4000-28 (S or AL)-64-10GLCSLX-FS-4000-28 (S or AL)-64-12GLCSLX-FS-4000-28 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
25 7/825 7/825 7/8
33 3/833 3/833 3/8
36 1/236 1/236 1/2
23 3/823 3/823 3/8
15 1/815 1/815 1/8
44 7/844 7/844 7/8
36’-0”36’-0”36’-0”
13’-4 7/8”15’-4 7/8”17’-4 7/8”
777
333
78’10’12’14’
GLCSL-FS-4000-28 (S or AL)-78-10GLCSL-FS-4000-28 (S or AL)-78-12GLCSL-FS-4000-28 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
25 7/825 7/825 7/8
31 3/831 3/831 3/8
34 1/234 1/234 1/2
23 3/823 3/823 3/8
15 1/815 1/815 1/8
44 7/844 7/844 7/8
36’-0”36’-0”36’-0”
13’-2 7/8”15’-2 7/8”17’-2 7/8”
777
444
83’10’12’14’
GLCS-FS-4000-28 (S or AL)-83-10GLCS-FS-4000-28 (S or AL)-83-12GLCS-FS-4000-28 (S or AL)-83-14
SteelSteelSteel
20’20’20’
464646
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
23 3/823 3/823 3/8
15 1/815 1/815 1/8
44 7/844 7/844 7/8
36’-0”36’-0”36’-0”
13’-0 7/8”15’-0 7/8”17’-0 7/8”
777
555
94’10’12’14’
GLCSLX-FS-4000-28 (S or AL)-94-10GLCSLX-FS-4000-28 (S or AL)-94-12GLCSLX-FS-4000-28 (S or AL)-94-14
SteelSteelSteel
30’30’30’
545454
25 7/825 7/825 7/8
33 3/833 3/833 3/8
36 1/236 1/236 1/2
23 3/823 3/823 3/8
15 1/815 1/815 1/8
44 7/844 7/844 7/8
36’-0”36’-0”36’-0”
13’-4 7/8”15’-4 7/8”17’-4 7/8”
777
444
103’
10’10’12’12’14’14’
GLCS-FS-4000-28 (S or AL)-103-10GLCSL-FS-4000-28 (S or AL)-103-10GLCS-FS-4000-28 (S or AL)-103-12
GLCSL-FS-4000-28 (S or AL)-103-12GLCS-FS-4000-28 (S or AL)-103-14
GLCSL-FS-4000-28 (S or AL)-103-14
SteelSteelSteelSteelSteelSteel
20’25’20’25’20’25’
545454545454
25 7/825 7/825 7/825 7/825 7/825 7/8
29 3/831 3/829 3/831 3/829 3/831 3/8
32 1/234 1/232 1/234 1/232 1/234 1/2
23 3/823 3/823 3/823 3/823 3/823 3/8
15 1/815 1/815 1/815 1/815 1/815 1/8
44 7/844 7/844 7/844 7/844 7/844 7/8
36’-0”36’-0”36’-0”36’-0”36’-0”36’-0”
13’-0 7/8”13’-2 7/8”15’-0 7/8”15’-2 7/8”17’-0 7/8”17’-2 7/8”
777777
656565
124’10’12’14’
GLCSLX-FS-4000-28 (S or AL)-124-10GLCSLX-FS-4000-28 (S or AL)-124-12GLCSLX-FS-4000-28 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
25 7/825 7/825 7/8
33 3/833 3/833 3/8
36 1/236 1/236 1/2
23 3/823 3/823 3/8
15 1/815 1/815 1/8
44 7/844 7/844 7/8
36’-0”36’-0”36’-0”
13’-4 7/8”15’-4 7/8”17’-4 7/8”
777
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
FREE STANDING WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH TS MODEL NUMBER TRACK
MAT.
RUNWAY BRIDGE SUPPORT STRUCTUREMAX.
L1L7 in
L8in
H3in
H3Ain
H4in
L3in
L6in OAW OAH D
in
SPT*
34’
28’10’12’14’
GLCSL-FS-4000-34 (S or AL)-28-10GLCSL-FS-4000-34 (S or AL)-28-12GLCSL-FS-4000-34 (S or AL)-28-14
SteelSteelSteel
25’25’25’
131313
25 7/825 7/825 7/8
31 3/831 3/831 3/8
34 1/234 1/234 1/2
25 3/825 3/825 3/8
15 1/815 1/815 1/8
47 1/247 1/247 1/2
36’-0”36’-0”36’-0”
13’-4 7/8”15’-4 7/8”17’-4 7/8”
777
222
33’10’12’14’
GLCS-FS-4000-34 (S or AL)-33-10GLCS-FS-4000-34 (S or AL)-33-12GLCS-FS-4000-34 (S or AL)-33-14
SteelSteelSteel
20’20’20’
999
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
25 3/825 3/825 3/8
15 1/815 1/815 1/8
47 1/247 1/247 1/2
36’-0”36’-0”36’-0”
13’-2 7/8”15’-2 7/8”17’-2 7/8”
777
333
34’10’12’14’
GLCSLX-FS-4000-34 (S or AL)-34-10GLCSLX-FS-4000-34 (S or AL)-34-12GLCSLX-FS-4000-34 (S or AL)-34-14
SteelSteelSteel
30’30’30’
999
25 7/825 7/825 7/8
33 3/833 3/833 3/8
36 1/236 1/236 1/2
25 3/825 3/825 3/8
15 1/815 1/815 1/8
47 1/247 1/247 1/2
36’-0”36’-0”36’-0”
13’-6 7/8”15’-6 7/8”17’-6 7/8”
777
222
43’10’12’14’
GLCS-FS-4000-34 (S or AL)-43-10GLCS-FS-4000-34 (S or AL)-43-12GLCS-FS-4000-34 (S or AL)-43-14
SteelSteelSteel
20’20’20’
131313
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
25 3/825 3/825 3/8
15 1/815 1/815 1/8
47 1/247 1/247 1/2
36’-0”36’-0”36’-0”
13’-2 7/8”15’-2 7/8”17’-2 7/8”
777
333
53’
10’10’12’12’14’14’
GLCS-FS-4000-34 (S or AL)-53-10GLCSL-FS-4000-34 (S or AL)-53-10GLCS-FS-4000-34 (S or AL)-53-12
GLCSL-FS-4000-34 (S or AL)-53-12GLCS-FS-4000-34 (S or AL)-53-14
GLCSL-FS-4000-34 (S or AL)-53-14
SteelSteelSteelSteelSteelSteel
20’25’20’25’20’25’
131313131313
25 7/825 7/825 7/825 7/825 7/825 7/8
29 3/831 3/829 3/831 3/829 3/831 3/8
32 1/234 1/232 1/234 1/232 1/234 1/2
25 3/825 3/825 3/825 3/825 3/825 3/8
15 1/815 1/815 1/815 1/815 1/815 1/8
47 1/247 1/247 1/247 1/247 1/247 1/2
36’-0”36’-0”36’-0”36’-0”36’-0”36’-0”
13’-2 7/8”13’-4 7/8”15’-2 7/8”15’-4 7/8”17’-2 7/8”17’-4 7/8”
777777
434343
63’10’12’14’
GLCS-FS-4000-34 (S or AL)-63-10GLCS-FS-4000-34 (S or AL)-63-12GLCS-FS-4000-34 (S or AL)-63-14
SteelSteelSteel
20’20’20’
191919
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
25 3/825 3/825 3/8
15 1/815 1/815 1/8
47 1/247 1/247 1/2
36’-0”36’-0”36’-0”
13’-2 7/8”15’-2 7/8”17’-2 7/8”
777
444
64’10’12’14’
GLCSLX-FS-4000-34 (S or AL)-64-10GLCSLX-FS-4000-34 (S or AL)-64-12GLCSLX-FS-4000-34 (S or AL)-64-14
SteelSteelSteel
30’30’30’
363636
25 7/825 7/825 7/8
33 3/833 3/833 3/8
36 1/236 1/236 1/2
25 3/825 3/825 3/8
15 1/815 1/815 1/8
51 5/851 5/851 5/8
36’-0”36’-0”36’-0”
13’-6 7/8”15’-6 7/8”17’-6 7/8”
777
333
78’10’12’14’
GLCSL-FS-4000-34 (S or AL)-78-10GLCSL-FS-4000-34 (S or AL)-78-12GLCSL-FS-4000-34 (S or AL)-78-14
SteelSteelSteel
25’25’25’
464646
25 7/825 7/825 7/8
31 3/831 3/831 3/8
34 1/234 1/234 1/2
25 3/825 3/825 3/8
15 1/815 1/815 1/8
51 5/851 5/851 5/8
36’-0”36’-0”36’-0”
13’-4 7/8”15’-4 7/8”17’-4 7/8”
777
444
83’10’12’14’
GLCS-FS-4000-34 (S or AL)-83-10GLCS-FS-4000-34 (S or AL)-83-12GLCS-FS-4000-34 (S or AL)-83-14
SteelSteelSteel
20’20’20’
464646
25 7/825 7/825 7/8
29 3/829 3/829 3/8
32 1/232 1/232 1/2
25 3/825 3/825 3/8
15 1/815 1/815 1/8
51 5/851 5/851 5/8
36’-0”36’-0”36’-0”
13’-2 7/8”15’-2 7/8”17’-2 7/8”
777
555
94’10’12’14’
GLCSLX-FS-4000-34 (S or AL)-94-10GLCSLX-FS-4000-34 (S or AL)-94-12GLCSLX-FS-4000-34 (S or AL)-94-14
SteelSteelSteel
30’30’30’
545454
25 7/825 7/825 7/8
33 3/833 3/833 3/8
36 1/236 1/236 1/2
25 3/825 3/825 3/8
15 1/815 1/815 1/8
51 5/851 5/851 5/8
36’-0”36’-0”36’-0”
13’-6 7/8”15’-6 7/8”17’-6 7/8”
777
444
103’
10’10’12’12’14’14’
GLCS-FS-4000-34 (S or AL)-103-10GLCSL-FS-4000-34 (S or AL)-103-10GLCS-FS-4000-34 (S or AL)-103-12
GLCSL-FS-4000-34 (S or AL)-103-12GLCS-FS-4000-34 (S or AL)-103-14
GLCSL-FS-4000-34 (S or AL)-103-14
SteelSteelSteelSteelSteelSteel
20’25’20’25’20’25’
545454545454
25 7/825 7/825 7/825 7/825 7/825 7/8
29 3/831 3/829 3/831 3/829 3/831 3/8
32 1/234 1/232 1/234 1/232 1/234 1/2
25 3/825 3/825 3/825 3/825 3/825 3/8
15 1/815 1/815 1/815 1/815 1/815 1/8
51 5/851 5/851 5/851 5/851 5/851 5/8
36’-0”36’-0”36’-0”36’-0”36’-0”36’-0”
13’-2 7/8”13’-4 7/8”15’-2 7/8”15’-4 7/8”17’-2 7/8”17’-4 7/8”
777777
656565
124’10’12’14’
GLCSLX-FS-4000-34 (S or AL)-124-10GLCSLX-FS-4000-34 (S or AL)-124-12GLCSLX-FS-4000-34 (S or AL)-124-14
SteelSteelSteel
30’30’30’
545454
25 7/825 7/825 7/8
33 3/833 3/833 3/8
36 1/236 1/236 1/2
25 3/825 3/825 3/8
15 1/815 1/815 1/8
51 5/851 5/851 5/8
36’-0”36’-0”36’-0”
13’-6 7/8”15’-6 7/8”17’-6 7/8”
777
555
*This column provides the total number of support assemblies based on the “L1” dimensions shown. Support assemblies are designed to AISC specifi ca ons and do not require bracing. If no movement of the support assembly is preferred, then bracing to the building steel is recommended (not included).
To Determine Hook Coverage: [Bridge Travel on Runway = Runway Length - (2xL8)] by [Hoist Trolley Travel on Bridge = Bridge Length - L3 - L6] (L6 allows for festoon stack-up).
Gorbel® Free Standing Work Sta on Bridge Crane Kits include: bridge, runways, the appropriate number of support assemblies, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Hoist and anchor bolts provided by others.
Dimensions are for reference only and are subject to change without no ce.
4000# CAPACITYFR
EE S
TAN
DIN
G W
OR
KST
ATIO
N C
RA
NES
33
STEELCEILING MOUNTED WORK STATION BRIDGE CRANES
ISOMETRIC VIEW
34
Model Number:
Capacity: pounds
Bridge Length (L): (OAL)
Runway Length: (OAL)L1: Are the number of support assemblies provided suffi cient?(See “HANGERS” column on dimensional chart pages)
Type of hanger required: Standard hanger with up to 20 inch drop. Support beam fl ange width ___________ inches Flush mounted, parallel Support beam fl ange width ___________ inches Flush mounted, perpendicular Support beam fl ange width ___________ inches Special hangersNote: Sway bracing is required on all systems except fl ush mounted systems. Sway bracing kits are available but are not included in the crane kit.
C: inches (hoist by others)
Gorbel® Ceiling Mounted Bridge Cranes include: bridge, runways, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63 feet and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Addi onal hanger points or longer drops, in excess of 20 inches, can be provided at an addi onal cost (hoist and sway bracing by others). Sway bracing kits are available but are not included in the crane kit.
Dimension and design details subject to change without no ce.
CEILIN
G M
OU
NTED
WO
RK
STATION
BR
IDG
E CR
AN
ES
L1
L1
L7
RUNWAY LENGTH
BRIDGE LENGTH (L)
L1
L1
L1
L1
L7
RUNWAY LENGTH
BRIDGE LENGTH (L)
GLC
GLCS(L,LX)
ALUMINUMCEILING MOUNTED WORK STATION BRIDGE CRANES
ISOMETRIC VIEW
35
Model Number:
Capacity: pounds
Bridge Length (L): (OAL)
Runway Length: (OAL)L1: Are the number of support assemblies provided suffi cient?(See “HANGERS” column on dimensional chart pages)
Type of hanger required: Standard hanger with up to 20 inch drop. Support beam fl ange width ___________ inches Flush mounted, parallel Support beam fl ange width ___________ inches Flush mounted, perpendicular Support beam fl ange width ___________ inches Special hangersNote: Sway bracing is required on all systems except fl ush mounted systems. Sway bracing kits are available but are not included in the crane kit.
C: inches (hoist by others)
Gorbel® Ceiling Mounted Bridge Cranes include: bridge, runways, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63 feet and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Addi onal hanger points or longer drops, in excess of 20 inches, can be provided at an addi onal cost (hoist and sway bracing by others). Sway bracing kits are available but are not included in the crane kit.
Dimension and design details subject to change without no ce.
CEI
LIN
G M
OU
NTE
D W
OR
KST
ATIO
N B
RID
GE
CR
AN
ES
L1
L1
L7
RUNWAY LENGTH
BRIDGE LENGTH (L)
STEELCEILING MOUNTED WORK STATION BRIDGE CRANES
36
Model Number:
Capacity: pounds
Bridge Length (L): (OAL)
Runway Length: (OAL)L1: Are the number of support assemblies provided suffi cient?(See “HANGERS” column on dimensional chart pages)
Type of hanger required: Standard hanger with up to 20 inch drop. Support beam fl ange width ___________ inches Flush mounted, parallel Support beam fl ange width ___________ inches Flush mounted, perpendicular Support beam fl ange width ___________ inches Special hangersNote: Sway bracing is required on all systems except fl ush mounted systems. Sway bracing kits are available but are not included in the crane kit.
C: inches (hoist by others)
Gorbel® Ceiling Mounted Bridge Cranes include: bridge, runways, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63 feet and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Addi onal hanger points or longer drops, in excess of 20 inches, can be provided at an addi onal cost (hoist and sway bracing by others). Sway bracing kits are available but are not included in the crane kit.
Dimension and design details subject to change without no ce.
CEILIN
G M
OU
NTED
WO
RK
STATION
BR
IDG
E CR
AN
ES
STEEL TRACK BRIDGE ON STEEL RUNWAYS
ALUMINUM TRACK BRIDGE ON STEEL RUNWAYS
COPED ALUMIINUM TRACK BRIDGE ON STEEL RUNWAYS
(L-L4)/2
H2
L3
L4
HOIST TROLLEY
BRIDGE LENGTH (L)
H4
C
L6
H3
H4(L-L4)/2
T1
(L-L4)/2
L3
L4
HOIST TROLLEY
BRIDGE LENGTH (L)
C
L6
H3AH4
(L-L4)/2
T1H2
(L-L4)/2
L3
L4
HOIST TROLLEYBRIDGE LENGTH (L)
C
L6
SEE NOTE**
H4(L-L4)/2
T1H2
Note**:250 SERIES = H3A - 3.25”500 SERIES = H3A - 5.12”1000 & 2000 SERIES STANDARD BRIDGES ARE A COPED 2-PIECE DESIGN
END VIEW
END VIEW
END VIEW
H2 L8
12” L1 L1 L1
RUNWAY LENGTH
8” MAX
L1 L1
SPLICE JOINT
HANGER
L1 12”
L8
L7
ENDTRUCK
GLC STEEL RUNWAY
SIDE VIEW
H2 L8
18” GLCS, GLCSL L1
RUNWAY LENGTH
48” MAXSPLICE JOINT
AND PLATE
HANGERL1
L8
L7
ENDTRUCK
GLCS, GLCSL, GLCSLXSTEEL RUNWAY
SIDE VIEW
H1
24” GLCSLX
18” GLCS, GLCSL24” GLCSLX
ALUMINUMCEILING MOUNTED WORK STATION BRIDGE CRANES
37
Model Number:
Capacity: pounds
Bridge Length (L): (OAL)
Runway Length: (OAL)L1: Are the number of support assemblies provided suffi cient?(See “HANGERS” column on dimensional chart pages)
Type of hanger required: Standard hanger with up to 20 inch drop. Support beam fl ange width ___________ inches Flush mounted, parallel Support beam fl ange width ___________ inches Flush mounted, perpendicular Support beam fl ange width ___________ inches Special hangersNote: Sway bracing is required on all systems except fl ush mounted systems. Sway bracing kits are available but are not included in the crane kit.
C: inches (hoist by others)
Gorbel® Ceiling Mounted Bridge Cranes include: bridge, runways, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63 feet and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Addi onal hanger points or longer drops, in excess of 20 inches, can be provided at an addi onal cost (hoist and sway bracing by others). Sway bracing kits are available but are not included in the crane kit.
Dimension and design details subject to change without no ce.
CEI
LIN
G M
OU
NTE
D W
OR
KST
ATIO
N B
RID
GE
CR
AN
ES
ALUMINUM TRACK BRIDGE ON ALUMINUM RUNWAYS
COPED ALUMINUM TRACK BRIDGE ON ALUMINUM RUNWAYS
(L-L4)/2
L3
L4
HOIST TROLLEY
BRIDGE LENGTH (L)
C
L6
H3H4
(L-L4)/2
T1H2
END VIEW
(L-L4)/2
L3
L4
HOIST TROLLEY
BRIDGE LENGTH (L)
C
L6
SEE NOTE**
H4
(L-L4)/2
T1H2
END VIEW
Note**:250 SERIES = H3 - 3.25”500 SERIES = H3 - 5.12”1000 & 2000 SERIES STANDARD BRIDGES ARE A COPED 2-PIECE DESIGN
H2
L8
18”
RUNWAY LENGTH
30” MAX
L1
SPLICE JOINT
HANGERL1 18”
L8
L7
ENDTRUCK
ALUMINUM RUNWAY
SIDE VIEW
CEILING MOUNTED WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH MODEL NUMBER TRACK
MATL.
BRIDGE RUNWAYMAX
L1T1in
L3in
L4
L6in
H3in
H3Ain
H4in
H2in
H1in
L7in
L8in
HANGERS(See Note)*
8’
11’-6”GLC250-8 (S or AL)-11.5
GLCS250-8 (S or AL)-11.5AL250-8-11.5
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
6’-6”6’-6”6’-6”
77
13 7/8
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
4 3/44 3/4
10 11/16
1 3/41 3/4
8
-9-
999
10 3/410 3/413 1/4
6 @ 379#4 @ 462#4 @ 443#
23’GLC250-8 (S or AL)-23
GLCS250-8 (S or AL)-23AL250-8-23
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
6’-6”6’-6”6’-6”
77
13 7/8
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
4 3/44 3/4
10 11/16
1 3/41 3/4
8
-9-
99
14
10 3/410 3/413 1/4
10 @ 379#4 @ 462#4 @ 443#
28’ GLCSL250-8 (S or AL)-28 Steel 25’ 1 1/2 5 1/16 6’-6” 7 14 15/16 22 11/16 4 3/4 1 3/4 11 9 10 3/4 4 @ 574#
33’GLC250-8 (S or AL)-33
GLCS250-8 (S or AL)-33AL250-8-33
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
6’-6”6’-6”6’-6”
77
13 7/8
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
4 3/44 3/4
10 11/16
1 3/41 3/4
8
-9-
99
20
10 3/410 3/413 1/4
14 @ 379#6 @ 462#6 @ 443#
43’GLC250-8 (S or AL)-43
GLCS250-8 (S or AL)-43AL250-8-43
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
6’-6”6’-6”6’-6”
77
13 7/8
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
4 3/44 3/4
10 11/16
1 3/41 3/4
8
-9-
131327
10 3/410 3/413 1/4
18 @ 379#6 @ 462#6 @ 443#
53’
GLC250-8 (S or AL)-53GLCS250-8 (S or AL)-53
AL250-8-53GLCSL250-8 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
1 1/21 1/2
2 11/161 1/2
5 1/165 1/167 3/165 1/16
6’-6”6’-6”6’-6”6’-6”
77
13 7/87
5 11/1612 15/1619 15/1614 15/16
13 7/1620 11/16
-22 11/16
4 3/44 3/4
10 11/164 3/4
1 3/41 3/4
81 3/4
-9-
11
13133013
10 3/410 3/413 1/410 3/4
22 @ 379#8 @ 462#8 @ 443#6 @ 574#
63’GLC250-8 (S or AL)-63
GLCS250-8 (S or AL)-63AL250-8-63
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
6’-6”6’-6”6’-6”
77
13 7/8
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
4 3/44 3/4
10 11/16
1 3/41 3/4
8
-9-
191937
10 3/410 3/413 1/4
26 @ 379#8 @ 462#8 @ 443#
78’ GLCSL250-8 (S or AL)-78 Steel 25’ 1 1/2 5 1/16 6’-6” 11 3/4 14 15/16 22 11/16 4 3/4 1 3/4 11 54 10 3/4 8 @ 574#
83’GLC250-8 (S or AL)-83
GLCS250-8 (S or AL)-83AL250-8-83
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
6’-6”6’-6”6’-6”
11 3/411 3/413 7/8
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
4 3/44 3/4
10 11/16
1 3/41 3/4
8
-9-
545447
10 3/410 3/413 1/4
34 @ 579#10 @ 462#10 @ 443#
103’
GLC250-8 (S or AL)-103GLCS250-8 (S or AL)-103
AL250-8-103GLCSL250-8 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
1 1/21 1/2
2 11/161 1/2
5 1/165 1/167 3/165 1/16
6’-6”6’-6”6’-6”6’-6”
11 3/411 3/413 7/811 3/4
5 11/1612 15/1619 15/1614 15/16
13 7/1620 11/16
-22 11/16
4 3/44 3/4
10 11/164 3/4
1 3/41 3/4
81 3/4
-9-
11
54545354
10 3/410 3/413 1/410 3/4
42 @ 379#12 @ 462#12 @ 443#10 @ 574#
10’
11’-6”GLC250-10 ( S or AL)-11.5
GLCS250-10 (S or AL)-11.5AL250-10-11.5
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
8’-0”8’-0”8’-0”
8 1/48 1/4
17 1/4
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
4 3/44 3/4
10 11/16
1 3/41 3/4
8
-9-
999
10 3/410 3/413 1/4
6 @ 382#4 @ 465#4 @ 446#
23’GLC250-10 (S or AL)-23
GLCS250-10 (S or AL)-23AL250-10-23
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
8’-0”8’-0”8’-0”
8 1/48 1/4
17 1/4
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
4 3/44 3/4
10 11/16
1 3/41 3/4
8
-9-
99
14
10 3/410 3/413 1/4
10 @ 382#4 @ 465#4 @ 446#
28’ GLCSL250-10 (S or AL)-28 Steel 25’ 1 1/2 5 1/16 8’-0” 8 1/4 14 15/16 22 11/16 4 3/4 1 3/4 11 9 10 3/4 4 @ 578#
33’GLC250-10 (S or AL)-33
GLCS250-10 (S or AL)-33AL250-10-33
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
8’-0”8’-0”8’-0”
8 1/48 1/4
17 1/4
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
4 3/44 3/4
10 11/16
1 3/41 3/4
8
-9-
99
20
10 3/410 3/413 1/4
14 @ 382#6 @ 465#6 @ 446#
43’GLC250-10 (S or AL)-43
GLCS250-10 (S or AL)-43AL250-10-43
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
8’-0”8’-0”8’-0”
8 1/48 1/4
17 1/4
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
4 3/44 3/4
10 11/16
1 3/41 3/4
8
-9-
131327
10 3/410 3/413 1/4
18 @ 382#6 @ 465#6 @ 446#
53’
GLC250-10 (S or AL)-53GLCS250-10 (S or AL)-53
AL250-10-53GLCSL250-10 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
1 1/21 1/2
2 11/161 1/2
5 1/165 1/167 3/165 1/16
8’-0”8’-0”8’-0”8’-0”
8 1/48 1/4
17 1/48 1/4
5 11/1612 15/1619 15/1614 15/16
13 7/1620 11/16
-22 11/16
4 3/44 3/4
10 11/164 3/4
1 3/41 3/4
81 3/4
-9-
11
13133013
10 3/410 3/413 1/410 3/4
22 @ 382#8 @ 465#8 @ 446#6 @ 578#
63’GLC250-10 (S or AL)-63
GLCS250-10 (S or AL)-63AL250-10-63
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
8’-0”8’-0”8’-0”
8 1/48 1/4
17 1/4
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
4 3/44 3/4
10 11/16
1 3/41 3/4
8
-9-
191937
10 3/410 3/413 1/4
26 @ 382#8 @ 465#8 @ 446#
78’ GLCSL250-10 (S or AL)-78 Steel 25’ 1 1/2 5 1/16 8’-0” 15 1/8 14 15/16 22 11/16 4 3/4 1 3/4 11 54 10 3/4 8 @ 578#
83’GLC250-10 (S or AL)-83
GLCS250-10 (S or AL)-83AL250-10-83
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
8’-0”8’-0”8’-0”
15 1/815 1/817 1/4
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
4 3/44 3/4
10 11/16
1 3/41 3/4
8
-9-
545447
10 3/410 3/413 1/4
34 @ 382#10 @ 465#10 @ 446#
103’
GLC250-10 (S or AL)-103GLCS250-10 (S or AL)-103
AL250-10-103GLCSL250-10 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
1 1/21 1/2
2 11/161 1/2
5 1/165 1/167 3/165 1/16
8’-0”8’-0”8’-0”8’-0”
15 1/815 1/817 1/415 1/8
5 11/1612 15/1619 15/1614 15/16
13 7/1620 11/16
-22 11/16
4 3/44 3/4
10 11/164 3/4
1 3/41 3/4
81 3/4
-9-
11
54545354
10 3/410 3/413 1/410 3/4
42 @ 382#12 @ 465#12 @ 446#10 @ 578#
*This column provides the total number of support hangers with the corresponding ver cal load applied by each support hanger (in pounds) based on the “L1” dimensions shown. Up to a 20” hanger drop will be provided by Gorbel. Addi onal hanger points or longer drops can be provided at an addi onal charge.
Gorbel® Ceiling Mounted Work Sta on Bridge Crane Kits include: bridge, runways, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Sway bracing is required on all systems except fl ush mounted systems (by others). Sway bracing kits are available but not included in the crane kit. Hoist provided by others.
Dimensions are for reference only and are subject to change without no ce.
38
250# CAPACITYC
EILING
MO
UN
TED W
OR
KSTATIO
N B
RID
GE C
RA
NES
250# CAPACITY
39
CEILING MOUNTED WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH MODEL NUMBER TRACK
MATL.
BRIDGE RUNWAYMAX
L1T1in
L3in
L4
L6in
H3in
H3Ain
H4in
H2in
H1in
L7in
L8in
HANGERS(See Note)*
15’
23’GLC250-15 (S or AL)-23
GLCS250-15 (S or AL)-23AL250-15-23
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
13’-0”13’-0”13’-0”
10 3/410 3/4
23 15/16
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
10 1/210 1/2
10 11/16
1 3/41 3/4
8
-9-
99
14
10 3/410 3/413 1/4
10 @ 398#4 @ 481#4 @ 456#
28’ GLCSL250-15 (S or AL)-28 Steel 25’ 1 1/2 5 1/16 13’-0” 10 3/4 14 15/16 22 11/16 10 1/2 1 3/4 11 9 10 3/4 4 @ 593#
33’GLC250-15 (S or AL)-33
GLCS250-15 (S or AL)-33AL250-15-33
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
13’-0”13’-0”13’-0”
10 3/410 3/4
23 15/16
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
10 1/210 1/2
10 11/16
1 3/41 3/4
8
-9-
99
20
10 3/410 3/413 1/4
14 @ 398#6 @ 481#6 @ 456#
43’GLC250-15 (S or AL)-43
GLCS250-15 (S or AL)-43AL250-15-43
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
13’-0”13’-0”13’-0”
10 3/410 3/4
23 15/16
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
10 1/210 1/2
10 11/16
1 3/41 3/4
8
-9-
131327
10 3/410 3/413 1/4
18 @ 396#6 @ 481#6 @ 456#
53’
GLC250-15 (S or AL)-53GLCS250-15 (S or AL)-53
AL250-15-53GLCSL250-15 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
1 1/21 1/2
2 11/161 1/2
5 1/165 1/167 3/165 1/16
13’-0”13’-0”13’-0”13’-0”
10 3/410 3/4
23 15/1610 3/4
5 11/1612 15/1619 15/1614 15/16
13 7/1620 11/16
-22 11/16
10 1/210 1/2
10 11/1610 1/2
1 3/41 3/4
81 3/4
-9-
11
13133013
10 3/410 3/413 1/410 3/4
22 @ 398#8 @ 481#8 @ 456#6 @ 593#
63’GLC250-15 (S or AL)-63
GLCS250-15 (S or AL)-63AL250-15-63
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
13’-0”13’-0”13’-0”
10 3/410 3/4
23 15/16
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
10 1/210 1/2
10 11/16
1 3/41 3/4
8
-9-
191937
10 3/410 3/413 1/4
26 @ 398#8 @ 481#8 @ 456#
78’ GLCSL250-15 (S or AL)-78 Steel 25’ 1 1/2 5 1/16 13’-0” 21 13/16 14 15/16 22 11/16 10 1/2 1 3/4 11 54 10 3/4 8 @ 593#
83’GLC250-15 (S or AL)-83
GLCS250-15 (S or AL)-83AL250-15-83
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
13’-0”13’-0”13’-0”
21 13/1621 13/1623 15/16
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
10 1/210 1/2
10 11/16
1 3/41 3/4
8
-9-
545447
10 3/410 3/413 1/4
34 @ 398#10 @ 481#10 @ 456#
103’
GLC250-15 (S or AL)-103GLCS250-15 (S or AL)-103
AL250-15-103GLCSL250-15 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
1 1/21 1/2
2 11/161 1/2
5 1/165 1/167 3/165 1/16
13’-0”13’-0”13’-0”13’-0”
21 13/1621 13/1623 15/1621 13/16
5 11/1612 15/1619 15/1614 15/16
13 7/1620 11/16
-22 11/16
10 1/210 1/2
10 11/1610 1/2
1 3/41 3/4
81 3/4
-9-
11
54545354
10 3/410 3/413 1/410 3/4
42 @ 398#12 @ 481#12 @ 456#10 @ 593#
20’
23’GLC250-20 (S or AL)-23
GLCS250-20 (S or AL)-23AL250-20-23
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
18’-0”18’-0”18’-0”
1212
27 5/16
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
10 1/210 1/2
10 11/16
1 3/41 3/4
8
-9-
99
14
10 3/410 3/413 1/4
10 @ 410#4 @ 493#4 @ 466#
28’ GLCSL250-20 (S or AL)-28 Steel 25’ 1 1/2 5 1/16 18’-0” 12 14 15/16 22 11/16 10 1/2 1 3/4 11 9 10 3/4 4 @ 606#
33’GLC250-20 (S or AL)-33
GLCS250-20 (S or AL)-33AL250-20-33
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
18’-0”18’-0”18’-0”
1212
27 5/16
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
10 1/210 1/2
10 11/16
1 3/41 3/4
8
-9-
99
20
10 3/410 3/413 1/4
14 @ 410#6 @ 493#6 @ 466#
43’GLC250-20 (S or AL)-43
GLCS250-20 (S or AL)-43AL250-20-43
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
18’-0”18’-0”18’-0”
1212
27 5/16
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
10 1/210 1/2
10 11/16
1 3/41 3/4
8
-9-
131327
10 3/410 3/413 1/4
18 @ 410#6 @ 493#6 @ 466#
53’
GLC250-20 (S or AL)-53GLCS250-20 (S or AL)-53
AL250-20-53GLCSL250-20 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
1 1/21 1/2
2 11/161 1/2
5 1/165 1/167 3/165 1/16
18’-0”18’-0”18’-0”18’-0”
1212
27 5/1612
5 11/1612 15/1619 15/1614 15/16
13 7/1620 11/16
-22 11/16
10 1/210 1/2
10 11/1610 1/2
1 3/41 3/4
81 3/4
-9-
11
13133013
10 3/410 3/413 1/410 3/4
22 @ 410#8 @ 493#8 @ 466#6 @ 606#
63’GLC250-20 (S or AL)-63
GLCS250-20 (S or AL)-63AL250-20-63
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
18’-0”18’-0”18’-0”
1212
27 5/16
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
10 1/210 1/2
10 11/16
1 3/41 3/4
8
-9-
191937
10 3/410 3/413 1/4
26 @ 410#8 @ 493#8 @ 466#
78’ GLCSL250-20 (S or AL)-78 Steel 25’ 1 1/2 5 1/16 18’-0” 25 3/16 14 15/16 22 11/16 10 1/2 1 3/4 11 54 10 3/4 8 @ 606#
83’GLC250-20 (S or AL)-83
GLCS250-20 (S or AL)-83AL250-20-83
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
18’-0”18’-0”18’-0”
25 3/1625 3/1627 5/16
5 11/1612 15/1619 15/16
13 7/1620 11/16
-
10 1/210 1/2
10 11/16
1 3/41 3/4
8
-9-
545447
10 3/410 3/413 1/4
34 @ 410#10 @ 493#10 @ 466#
103’
GLC250-20 (S or AL)-103GLCS250-20 (S or AL)-103
AL250-20-103GLCSL250-20 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
1 1/21 1/2
2 11/161 1/2
5 1/165 1/167 3/165 1/16
18’-0”18’-0”18’-0”18’-0”
25 3/1625 3/1627 5/1625 3/16
5 11/1612 15/1619 15/1614 15/16
13 7/1620 11/16
-22 11/16
10 1/210 1/2
10 11/1610 1/2
1 3/41 3/4
81 3/4
-9-
11
54545354
10 3/410 3/413 1/410 3/4
42 @ 410#12 @ 493#12 @ 466#10 @ 606#
*This column provides the total number of support hangers with the corresponding ver cal load applied by each support hanger (in pounds) based on the “L1” dimensions shown. Up to a 20” hanger drop will be provided by Gorbel. Addi onal hanger points or longer drops can be provided at an addi onal charge.
Gorbel® Ceiling Mounted Work Sta on Bridge Crane Kits include: bridge, runways, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Sway bracing is required on all systems except fl ush mounted systems (by others). Sway bracing kits are available but not included in the crane kit. Hoist provided by others.
Dimensions are for reference only and are subject to change without no ce.
CEI
LIN
G M
OU
NTE
D W
OR
KST
ATIO
N B
RID
GE
CR
AN
ES
CEILING MOUNTED WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH MODEL NUMBER TRACK
MATL.
BRIDGE RUNWAYMAX
L1T1in
L3in
L4
L6in
H3in
H3Ain
H4in
H2in
H1in
L7in
L8in
HANGERS(See Note)*
23’
23’GLC250-23 (S or AL)-23
GLCS250-23 (S or AL)-23AL250-23-23
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
21’-0”21’-0”20’-0”
13 1/413 1/430 5/8
5 11/1612 15/1619 15/16
18 1/1625 5/16
-
10 1/210 1/2
10 11/16
1 3/41 3/4
8
-9-
99
14
10 3/410 3/413 1/4
10 @ 417#4 @ 500#4 @ 470#
28’ GLCSL250-23 (S or AL)-28 Steel 25’ 1 1/2 5 1/16 21’-0” 13 1/4 14 15/16 27 5/16 10 1/2 1 3/4 11 9 10 3/4 4 @ 613#
33’GLC250-23 (S or AL)-33
GLCS250-23 (S or AL)-33AL250-23-33
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
21’-0”21’-0”20’-0”
13 1/413 1/430 5/8
5 11/1612 15/1619 15/16
18 1/1625 5/16
-
10 1/210 1/2
10 11/16
1 3/41 3/4
8
-9-
99
20
10 3/410 3/413 1/4
14 @ 417#6 @ 500#6 @ 470#
43’GLC250-23 (S or AL)-43
GLCS250-23 (S or AL)-43AL250-23-43
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
21’-0”21’-0”20’-0”
13 1/413 1/430 5/8
5 11/1612 15/1619 15/16
18 1/1625 5/16
-
10 1/210 1/2
10 11/16
1 3/41 3/4
8
-9-
131327
10 3/410 3/413 1/4
18 @ 417#6 @ 500#6 @ 470#
53’
GLC250-23 (S or AL)-53GLCS250-23 (S or AL)-53
AL250-23-53GLCSL250-23 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
1 1/21 1/2
2 11/161 1/2
5 1/165 1/167 3/165 1/16
21’-0”21’-0”20’-0”21’-0”
13 1/413 1/430 5/813 1/4
5 11/1612 15/1619 15/1614 15/16
18 1/1625 5/16
-27 5/16
10 1/210 1/2
10 11/1610 1/2
1 3/41 3/4
81 3/4
-9-
11
13133013
10 3/410 3/413 1/410 3/4
22 @ 417#8 @ 500#8 @ 470#6 @ 613#
63’GLC250-23 (S or AL)-63
GLCS250-23 (S or AL)-63AL250-23-63
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
21’-0”21’-0”20’-0”
13 1/413 1/430 5/8
5 11/1612 15/1619 15/16
18 1/1625 5/16
-
10 1/210 1/2
10 11/16
1 3/41 3/4
8
-9-
191937
10 3/410 3/413 1/4
26 @ 417#8 @ 500#8 @ 470#
78’ GLCSL250-23 (S or AL)-78 Steel 25’ 1 1/2 5 1/16 21’-0” 28 1/2 14 15/16 27 5/16 10 1/2 1 3/4 11 54 10 3/4 8 @ 613#
83’GLC250-23 (S or AL)-83
GLCS250-23 (S or AL)-83AL250-23-83
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
21’-0”21’-0”20’-0”
28 1/228 1/230 5/8
5 11/1612 15/1619 15/16
18 1/1625 5/16
-
10 1/210 1/2
10 11/16
1 3/41 3/4
8
-9-
545447
10 3/410 3/413 1/4
34 @ 417#10 @ 500#10 @ 470#
103’
GLC250-23 (S or AL)-103GLCS250-23 (S or AL)-103
AL250-23-103GLCSL250-23 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
1 1/21 1/2
2 11/161 1/2
5 1/165 1/167 3/165 1/16
21’-0”21’-0”20’-0”21’-0”
28 1/228 1/230 5/828 1/2
5 11/1612 15/1619 15/1614 15/16
18 1/1625 5/16
-27 5/16
10 1/210 1/2
10 11/1610 1/2
1 3/41 3/4
81 3/4
-9-
11
54545354
10 3/410 3/413 1/410 3/4
42 @ 417#12 @ 500#12 @ 470#10 @ 613#
28’
23’GLC250-28 (S or AL)-23
GLCS250-28 (S or AL)-23AL250-28-23
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
25’-0”25’-0”25’-0”
15 3/415 3/437 3/8
8 1/1615 5/1624 3/8
18 1/1625 5/16
-
12 1/212 1/2
12 11/16
1 3/41 3/4
10
-9-
99
14
21 3/421 3/423 3/8
10 @ 471#4 @ 554#4 @ 489#
28’ GLCSL250-28 (S or AL)-28 Steel 25’ 1 1/2 5 1/16 25’-0” 15 3/4 17 5/16 27 5/16 12 1/2 1 3/4 11 9 21 3/4 4 @ 667#
33’GLC250-28 (S or AL)-33
GLCS250-28 (S or AL)-33AL250-28-33
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
25’-0”25’-0”25’-0”
15 3/415 3/437 3/8
8 1/1615 5/1624 3/8
18 1/1625 5/16
-
12 1/212 1/2
12 11/16
1 3/41 3/4
10
-9-
99
20
21 3/421 3/423 3/8
14 @ 471#6 @ 554#6 @ 489#
43’GLC250-28 (S or AL)-43
GLCS250-28 (S or AL)-43AL250-28-43
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
25’-0”25’-0”25’-0”
15 3/415 3/437 3/8
8 1/1615 5/1624 3/8
18 1/1625 5/16
-
12 1/212 1/2
12 11/16
1 3/41 3/4
10
-9-
131327
21 3/421 3/423 3/8
18 @ 471#6 @ 554#6 @ 489#
53’
GLC250-28 (S or AL)-53GLCS250-28 (S or AL)-53
AL250-28-53GLCSL250-28 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
1 1/21 1/2
2 11/161 1/2
5 1/165 1/167 3/165 1/16
25’-0”25’-0”25’-0”25’-0”
15 3/415 3/437 3/815 3/4
8 1/1615 5/1624 3/8
17 5/16
18 1/1625 5/16
-27 5/16
12 1/212 1/2
12 11/1612 1/2
1 3/41 3/4
101 3/4
-9-
11
13133013
21 3/421 3/423 3/821 3/4
22 @ 471#8 @ 554#8 @ 489#6 @ 667#
63’GLC250-28 (S or AL)-63
GLCS250-28 (S or AL)-63AL250-28-63
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
25’-0”25’-0”25’-0”
15 3/415 3/437 3/8
8 1/1615 5/1624 3/8
18 1/1625 5/16
-
12 1/212 1/2
12 11/16
1 3/41 3/4
10
-9-
191937
21 3/421 3/423 3/8
26 @ 471#8 @ 554#8 @ 489#
78’ GLCSL250-28 (S or AL)-78 Steel 25’ 1 1/2 5 1/16 25’-0” 35 3/16 17 5/16 27 5/16 12 1/2 1 3/4 11 54 21 3/4 8 @ 667#
83’GLC250-28 (S or AL)-83
GLCS250-28 (S or AL)-83AL250-28-83
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
5 1/165 1/167 3/16
25’-0”25’-0”25’-0”
35 3/1635 3/1637 3/8
8 1/1615 5/1624 3/8
18 1/1625 5/16
-
12 1/212 1/2
12 11/16
1 3/41 3/4
10
-9-
545447
21 3/421 3/423 3/8
34 @ 471#10 @ 554#10 @ 489#
103’
GLC250-28 (S or AL)-103GLCS250-28 (S or AL)-103
AL250-28-103GLCSL250-28 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
1 1/21 1/2
2 11/161 1/2
5 1/165 1/167 3/165 1/16
25’-0”25’-0”25’-0”25’-0”
35 3/1635 3/1637 3/8
35 3/16
8 1/1615 5/1624 3/8
17 5/16
18 1/1625 5/16
-27 5/16
12 1/212 1/2
12 11/1612 1/2
1 3/41 3/4
101 3/4
-9-
11
54545354
21 3/421 3/423 3/821 3/4
42 @ 471#12 @ 554#12 @ 489#10 @ 667#
*This column provides the total number of support hangers with the corresponding ver cal load applied by each support hanger (in pounds) based on the “L1” dimensions shown. Up to a 20” hanger drop will be provided by Gorbel. Addi onal hanger points or longer drops can be provided at an addi onal charge.
Gorbel® Ceiling Mounted Work Sta on Bridge Crane Kits include: bridge, runways, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Sway bracing is required on all systems except fl ush mounted systems (by others). Sway bracing kits are available but not included in the crane kit. Hoist provided by others.
Dimensions are for reference only and are subject to change without no ce.
40
250# CAPACITYC
EILING
MO
UN
TED W
OR
KSTATIO
N B
RID
GE C
RA
NES
CEILING MOUNTED WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH MODEL NUMBER TRACK
MATL.
BRIDGE RUNWAYMAX
L1T1in
L3in
L4
L6in
H3in
H3Ain
H4in
H2in
H1in
L7in
L8in
HANGERS(See Note)*
8’
11’-6”GLC500-8 (S or AL)-11.5
GLCS500-8 (S or AL)-11.5AL500-8-11.5
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
6’-6”6’-6”6’-6”
8 11/168 11/1613 7/8
8 7/816 1/223 7/8
16 3/824-
6 11/166 11/16
12 11/16
2 3/82 3/8
10
-10-
999
13 3/1613 3/1613 1/4
6 @ 743#4 @ 867#4 @ 810#
23’GLC500-8 (S or AL)-23
GLCS500-8 (S or AL)-23AL500-8-23
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
6’-6”6’-6”6’-6”
8 11/168 11/1613 7/8
8 7/816 1/223 7/8
16 3/824-
6 11/166 11/16
12 11/16
2 3/82 3/8
10
-10-
99
14
13 3/1613 3/1613 1/4
10 @ 743#4 @ 867#4 @ 810#
28’ GLCSL500-8 (S or AL)-28 Steel 25’ 2 13/16 7 1/8 6’-6” 8 11/16 18 7/8 26 3/8 6 11/16 2 3/8 12 3/8 9 13 3/16 4 @ 986#
33’GLC500-8 (S or AL)-33
GLCS500-8 (S or AL)-33AL500-8-33
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
6’-6”6’-6”6’-6”
8 11/168 11/1613 7/8
8 7/816 1/223 7/8
16 3/824-
6 11/166 11/16
12 11/16
2 3/82 3/8
10
-10-
99
20
13 3/1613 3/1613 1/4
14 @ 743#6 @ 867#6 @ 810#
34’ GLCSLX500-8 (S or AL)-34 Steel 30’ 2 13/16 7 1/8 6’-6” 8 11/16 20 7/8 28 3/8 6 11/16 2 3/8 14 3/8 9 13 3/16 4 @ 1,049#
43’GLC500-8 (S or AL)-43
GLCS500-8 (S or AL)-43AL500-8-43
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
6’-6”6’-6”6’-6”
8 11/168 11/1613 7/8
8 7/816 1/223 7/8
16 3/824-
6 11/166 11/16
12 11/16
2 3/82 3/8
10
-10-
131327
13 3/1613 3/1613 1/4
18 @ 743#6 @ 867#6 @ 810#
53’
GLC500-8 (S or AL)-53GLCS500-8 (S or AL)-53
AL500-8-53GLCSL500-8 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
2 13/162 13/162 11/162 13/16
7 1/87 1/8
7 3/167 1/8
6’-6”6’-6”6’-6”6’-6”
8 11/168 11/1613 7/8
8 11/16
8 7/816 1/223 7/818 7/8
16 3/824-
26 3/8
6 11/166 11/16
12 11/166 11/16
2 3/82 3/8
102 3/8
-10-
12 3/8
13133013
13 3/1613 3/1613 1/4
13 3/16
22 @ 743#8 @ 867#8 @ 810#6 @ 986#
63’GLC500-8 (S or AL)-63
GLCS500-8 (S or AL)-63AL500-8-63
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
6’-6”6’-6”6’-6”
8 11/168 11/1613 7/8
8 7/816 1/223 7/8
16 3/824-
6 11/166 11/16
12 11/16
2 3/82 3/8
10
-10-
191937
13 3/1613 3/1613 1/4
26 @ 743#8 @ 867#8 @ 810#
64’ GLCSLX500-8 (S or AL)-64 Steel 30’ 2 13/16 7 1/8 6’-6” 13 13/16 20 7/8 28 3/8 6 11/16 2 3/8 14 3/8 46 13 3/16 6 @ 1,049#78’ GLCSL500-8 (S or AL)-78 Steel 25’ 2 13/16 7 1/8 6’-6” 13 13/16 18 7/8 26 3/8 6 11/16 2 3/8 12 3/8 54 13 3/16 8 @ 986#
83’GLC500-8 (S or AL)-83
GLCS500-8 (S or AL)-83AL500-8-83
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
6’-6”6’-6”6’-6”
13 13/1613 13/16
13 7/8
8 7/816 1/223 7/8
16 3/824-
6 11/166 11/16
12 11/16
2 3/82 3/8
10
-10-
545447
13 3/1613 3/1613 1/4
34 @ 743#10 @ 867#10 @ 810#
94’ GLCSLX-8 (S or AL)-94 Steel 30’ 2 13/16 7 1/8 6’-6” 13 13/16 20 7/8 28 3/8 6 11/16 2 3/8 14 3/8 54 13 3/16 8 @ 1,049#
103’
GLC500-8 (S or AL)-103GLCS500-8 (S or AL)-103
AL500-8-103GLCSL500-8 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
2 13/162 13/162 11/162 13/16
7 1/87 1/8
7 3/167 1/8
6’-6”6’-6”6’-6”6’-6”
13 13/1613 13/16
13 7/813 13/16
8 7/816 1/223 7/818 7/8
16 3/824-
26 3/8
6 11/166 11/16
12 11/166 11/16
2 3/82 3/8
102 3/8
-10-
12 3/8
54545354
13 3/1613 3/1613 1/4
13 3/16
42 @ 743#12 @ 867#12 @ 810#10 @ 986#
124’ GLCSLX500-8 (S or AL)-124 Steel 30’ 2 13/16 7 1/8 6’-6” 13 13/16 20 7/8 28 3/8 6 11/16 2 3/8 14 3/8 54 13 3/16 10 @ 1,049#
10’
11’-6”GLC500-10 ( S or AL)-11.5
GLCS500-10 (S or AL)-11.5AL500-10-11.5
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
8’-0”8’-0”8’-0”
9 15/169 15/1617 1/4
8 7/816 1/223 7/8
16 3/824-
6 11/166 11/16
12 11/16
2 3/82 3/8
10
-10-
999
13 3/1613 3/1613 1/4
6 @ 747#4 @ 871#4 @ 813#
23’GLC500-10 (S or AL)-23
GLCS500-10 (S or AL)-23AL500-10-23
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
8’-0”8’-0”8’-0”
9 15/169 15/1617 1/4
8 7/816 1/223 7/8
16 3/824-
6 11/166 11/16
12 11/16
2 3/82 3/8
10
-10-
99
14
13 3/1613 3/1613 1/4
10 @ 747#4 @ 871#4 @ 813#
28’ GLCSL500-10 (S or AL)-28 Steel 25’ 2 13/16 7 1/8 8’-0” 9 15/16 18 7/8 26 3/8 6 11/16 2 3/8 12 3/8 9 13 3/16 4 @ 990#
33’GLC500-10 (S or AL)-33
GLCS500-10 (S or AL)-33AL500-10-33
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
8’-0”8’-0”8’-0”
9 15/169 15/1617 1/4
8 7/816 1/223 7/8
16 3/824-
6 11/166 11/16
12 11/16
2 3/82 3/8
10
-10-
99
20
13 3/1613 3/1613 1/4
14 @ 747#6 @ 871#6 @ 813#
34’ GLCSLX500-10 (S or AL)-34 Steel 30’ 2 13/16 7 1/8 8’-0” 9 15/16 20 7/8 28 3/8 6 11/16 2 3/8 14 3/8 9 13 3/16 4 @ 1,053#
43’GLC500-10 (S or AL)-43
GLCS500-10 (S or AL)-43AL500-10-43
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
8’-0”8’-0”8’-0”
9 15/169 15/1617 1/4
8 7/816 1/223 7/8
16 3/824-
6 11/166 11/16
12 11/16
2 3/82 3/8
10
-10-
131327
13 3/1613 3/1613 1/4
18 @ 747#6 @ 871#6 @ 813#
53’
GLC500-10 (S or AL)-53GLCS500-10 (S or AL)-53
AL500-10-53GLCSL500-10 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
2 13/162 13/162 11/162 13/16
7 1/87 1/8
7 3/167 1/8
8’-0”8’-0”8’-0”8’-0”
9 15/169 15/1617 1/4
9 15/16
8 7/816 1/223 7/818 7/8
16 3/824-
26 3/8
6 11/166 11/16
12 11/166 11/16
2 3/82 3/8
102 3/8
-10-
12 3/8
13133013
13 3/1613 3/1613 1/4
13 3/16
22 @ 747#8 @ 871#8 @ 813#6 @ 990#
63’GLC500-10 (S or AL)-63
GLCS500-10 (S or AL)-63AL500-10-63
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
8’-0”8’-0”8’-0”
9 15/169 15/1617 1/4
8 7/816 1/223 7/8
16 3/824-
6 11/166 11/16
12 11/16
2 3/82 3/8
10
-10-
191937
13 3/1613 3/1613 1/4
26 @ 747#8 @ 871#8 @ 813#
64’ GLCSLX500-10 (S or AL)-64 Steel 30’ 2 13/16 7 1/8 8’-0” 17 3/16 20 7/8 28 3/8 6 11/16 2 3/8 14 3/8 46 13 3/16 6 @ 1,053#78’ GLCSL500-10 (S or AL)-78 Steel 25’ 2 13/16 7 1/8 8’-0” 17 3/16 18 7/8 26 3/8 6 11/16 2 3/8 12 3/8 54 13 3/16 8 @ 990#
83’GLC500-10 (S or AL)-83
GLCS500-10 (S or AL)-83AL500-10-83
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
8’-0”8’-0”8’-0”
17 3/1617 3/1617 1/4
8 7/816 1/223 7/8
16 3/824-
6 11/166 11/16
12 11/16
2 3/82 3/8
10
-10-
545447
13 3/1613 3/1613 1/4
34 @ 747#10 @ 871#10 @ 813#
94’ GLCSLX500-10 (S or AL)-94 Steel 30’ 2 13/16 7 1/8 8’-0” 17 3/16 20 7/8 28 3/8 6 11/16 2 3/8 14 3/8 54 13 3/16 8 @ 1,053#
103’
GLC500-10 (S or AL)-103GLCS500-10 (S or AL)-103
AL500-10-103GLCSL500-10 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
2 13/162 13/162 11/162 13/16
7 1/87 1/8
7 3/167 1/8
8’-0”8’-0”8’-0”8’-0”
17 3/1617 3/1617 1/4
17 3/16
8 7/816 1/223 7/818 7/8
16 3/824-
26 3/8
6 11/166 11/16
12 11/166 11/16
2 3/82 3/8
102 3/8
-10-
12 3/8
54545354
13 3/1613 3/1613 1/4
13 3/16
42 @ 747#12 @ 871#12 @ 813#10 @ 990#
124’ GLCSLX500-10 (S or AL)-124 Steel 30’ 2 13/16 7 1/8 8’-0” 17 3/16 20 7/8 28 3/8 6 11/16 2 3/8 14 3/8 54 13 3/16 10 @ 1,053#
*This column provides the total number of support hangers with the corresponding ver cal load applied by each support hanger (in pounds) based on the “L1” dimensions shown. Up to a 20” hanger drop will be provided by Gorbel. Addi onal hanger points or longer drops can be provided at an addi onal charge.
Gorbel® Ceiling Mounted Work Sta on Bridge Crane Kits include: bridge, runways, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Sway bracing is required on all systems except fl ush mounted systems (by others). Sway bracing kits are available but not included in the crane kit. Hoist provided by others.
Dimensions are for reference only and are subject to change without no ce.
500# CAPACITY
41
CEI
LIN
G M
OU
NTE
D W
OR
KST
ATIO
N B
RID
GE
CR
AN
ES
42
500# CAPACITYCEILING MOUNTED WORK STATION BRIDGE CRANES
BRIDGE LENGTH
(L)
RUNWAY LENGTH MODEL NUMBER TRACK
MATL.
BRIDGE RUNWAYMAX
L1T1in
L3in
L4
L6in
H3in
H3Ain
H4in
H2in
H1in
L7in
L8in
HANGERS(See Note)*
15’
23’GLC500-15 (S or AL)-23
GLCS500-15 (S or AL)-23AL500-15-23
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
13’-0”13’-0”13’-0”
12 7/1612 7/16
23 15/16
8 7/816 1/223 7/8
16 3/824-
12 13/1612 13/1612 11/16
2 3/82 3/8
10
-10-
99
14
13 3/1613 3/1613 1/4
10 @ 774#4 @ 898#4 @ 825#
28’ GLCSL500-15 (S or AL)-28 Steel 25’ 2 13/16 7 1/8 13’-0” 12 7/16 18 7/8 26 3/8 12 13/16 2 3/8 12 3/8 9 13 3/16 4 @ 1,017#
33’GLC500-15 (S or AL)-33
GLCS500-15 (S or AL)-33AL500-15-33
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
13’-0”13’-0”13’-0”
12 7/1612 7/16
23 15/16
8 7/816 1/223 7/8
16 3/824-
12 13/1612 13/1612 11/16
2 3/82 3/8
10
-10-
99
20
13 3/1613 3/1613 1/4
14 @ 774#6 @ 898#6 @ 825#
34’ GLCSLX500-15 (S or AL)-34 Steel 30’ 2 13/16 7 1/8 13’-0” 12 7/16 20 7/8 28 3/8 12 13/16 2 3/8 14 3/8 9 13 3/16 4 @ 1,079#
43’GLC500-15 (S or AL)-43
GLCS500-15 (S or AL)-43AL500-15-43
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
13’-0”13’-0”13’-0”
12 7/1612 7/16
23 15/16
8 7/816 1/223 7/8
16 3/824-
12 13/1612 13/1612 11/16
2 3/82 3/8
10
-10-
131327
13 3/1613 3/1613 1/4
18 @ 774#6 @ 898#6 @ 825#
53’
GLC500-15 (S or AL)-53GLCS500-15 (S or AL)-53
AL500-15-53GLCSL500-15 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
2 13/162 13/162 11/162 13/16
7 1/87 1/8
7 3/167 1/8
13’-0”13’-0”13’-0”13’-0”
12 7/1612 7/16
23 15/1612 7/16
8 7/816 1/223 7/818 7/8
16 3/824-
26 3/8
12 13/1612 13/1612 11/1612 13/16
2 3/82 3/8
102 3/8
-10-
12 3/8
13133013
13 3/1613 3/1613 1/4
13 3/16
22 @ 774#8 @ 898#8 @ 825#
6 @ 1,017#
63’GLC500-15 (S or AL)-63
GLCS500-15 (S or AL)-63AL500-15-63
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
13’-0”13’-0”13’-0”
12 7/1612 7/16
23 15/16
8 7/816 1/223 7/8
16 3/824-
12 13/1612 13/1612 11/16
2 3/82 3/8
10
-10-
191937
13 3/1613 3/1613 1/4
26 @ 774#8 @ 898#8 @ 825#
64’ GLCSLX500-15 (S or AL)-64 Steel 30’ 2 13/16 7 1/8 13’-0” 23 7/8 20 7/8 28 3/8 12 13/16 2 3/8 14 3/8 46 13 3/16 6 @ 1,079#78’ GLCSL500-15 (S or AL)-78 Steel 25’ 2 13/16 7 1/8 13’-0” 23 7/8 18 7/8 26 3/8 12 13/16 2 3/8 12 3/8 54 13 3/16 8 @ 1,017#
83’GLC500-15 (S or AL)-83
GLCS500-15 (S or AL)-83AL500-15-83
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
13’-0”13’-0”13’-0”
23 7/823 7/8
23 15/16
8 7/816 1/223 7/8
16 3/824-
12 13/1612 13/1612 11/16
2 3/82 3/8
10
-10-
545447
13 3/1613 3/1613 1/4
34 @ 774#10 @ 898#10 @ 825#
94’ GLCSLX-15 (S or AL)-94 Steel 30’ 2 13/16 7 1/8 13’-0” 23/7/8 20 7/8 28 3/8 12 13/16 2 3/8 14 3/8 54 13 3/16 8 @ 1,079#
103’
GLC500-15 (S or AL)-103GLCS500-15 (S or AL)-103
AL500-15-103GLCSL500-15 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
2 13/162 13/162 11/162 13/16
7 1/87 1/8
7 3/167 1/8
13’-0”13’-0”13’-0”13’-0”
23 7/823 7/8
23 15/1623 7/8
8 7/816 1/223 7/818 7/8
16 3/824-
26 3/8
12 13/1612 13/1612 11/1612 13/16
2 3/82 3/8
102 3/8
-10-
12 3/8
54545354
13 3/1613 3/1613 1/4
13 3/16
42 @ 774#12 @ 898#12 @ 825#
10 @ 1,017#124’ GLCSLX500-15 (S or AL)-124 Steel 30’ 2 13/16 7 1/8 13’-0” 23 7/8 20 7/8 28 3/8 12 13/16 2 3/8 14 3/8 54 13 3/16 10 @ 1,079#
20’
23’GLC500-20 (S or AL)-23
GLCS500-20 (S or AL)-23AL500-20-23
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
18’-0”18’-0”18’-0”
13 11/1613 11/1627 5/16
8 7/816 1/223 7/8
16 3/824-
12 13/1612 13/1612 11/16
2 3/82 3/8
10
-10-
99
14
13 3/1613 3/1613 1/4
10 @ 792#4 @ 916#4 @ 837#
28’ GLCSL500-20 (S or AL)-28 Steel 25’ 2 13/16 7 1/8 18’-0” 13 11/16 18 7/8 26 3/8 12 13/16 2 3/8 12 3/8 9 13 3/16 4 @ 1,035#
33’GLC500-20 (S or AL)-33
GLCS500-20 (S or AL)-33AL500-20-33
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
18’-0”18’-0”18’-0”
13 11/1613 11/1627 5/16
8 7/816 1/223 7/8
16 3/824-
12 13/1612 13/1612 11/16
2 3/82 3/8
10
-10-
99
20
13 3/1613 3/1613 1/4
14 @ 792#6 @ 916#6 @ 837#
34’ GLCSLX500-20 (S or AL)-34 Steel 30’ 2 13/16 7 1/8 18’-0” 13 11/16 20 7/8 28 3/8 12 13/16 2 3/8 14 3/8 9 13 3/16 4 @ 1,098#
43’GLC500-20 (S or AL)-43
GLCS500-20 (S or AL)-43AL500-20-43
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
18’-0”18’-0”18’-0”
13 11/1613 11/1627 5/16
8 7/816 1/223 7/8
16 3/824-
12 13/1612 13/1612 11/16
2 3/82 3/8
10
-10-
131327
13 3/1613 3/1613 1/4
18 @ 792#6 @ 916#6 @ 837#
53’
GLC500-20 (S or AL)-53GLCS500-20 (S or AL)-53
AL500-20-53GLCSL500-20 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
2 13/162 13/162 11/162 13/16
7 1/87 1/8
7 3/167 1/8
18’-0”18’-0”18’-0”18’-0”
13 11/1613 11/1627 5/16
13 11/16
8 7/816 1/223 7/818 7/8
16 3/824-
26 3/8
12 13/1612 13/1612 11/1612 13/16
2 3/82 3/8
102 3/8
-10-
12 3/8
13133013
13 3/1613 3/1613 1/4
13 3/16
22 @ 792#8 @ 916#8 @ 837#
6 @ 1,035#
63’GLC500-20 (S or AL)-63
GLCS500-20 (S or AL)-63AL500-20-63
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
18’-0”18’-0”18’-0”
13 11/1613 11/1627 5/16
8 7/816 1/223 7/8
16 3/824-
12 13/1612 13/1612 11/16
2 3/82 3/8
10
-10-
191937
13 3/1613 3/1613 1/4
26 @ 792#8 @ 916#8 @ 837#
64’ GLCSLX500-20 (S or AL)-64 Steel 30’ 2 13/16 7 1/8 18’-0” 27 1/4 20 7/8 28 3/8 12 13/16 2 3/8 14 3/8 46 13 3/16 6 @ 1,098#78’ GLCSL500-20 (S or AL)-78 Steel 25’ 2 13/16 7 1/8 18’-0” 27 1/4 18 7/8 26 3/8 12 13/16 2 3/8 12 3/8 54 13 3/16 8 @ 1,035#
83’GLC500-20 (S or AL)-83
GLCS500-20 (S or AL)-83AL500-20-83
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
18’-0”18’-0”18’-0”
27 1/427 1/4
27 5/16
8 7/816 1/223 7/8
16 3/824-
12 13/1612 13/1612 11/16
2 3/82 3/8
10
-10-
545447
13 3/1613 3/1613 1/4
34 @ 792#10 @ 916#10 @ 837#
94’ GLCSLX500-20 (S or AL)-94 Steel 30’ 2 13/16 7 1/8 18’-0” 27 1/4 20 7/8 28 3/8 12 13/16 2 3/8 14 3/8 54 13 3/16 8 @ 1,098#
103’
GLC500-20 (S or AL)-103GLCS500-20 (S or AL)-103
AL500-20-103GLCSL500-20 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
2 13/162 13/162 11/162 13/16
7 1/87 1/8
7 3/167 1/8
18’-0”18’-0”18’-0”18’-0”
27 1/427 1/4
27 5/1627 1/4
8 7/816 1/223 7/818 7/8
16 3/824-
26 3/8
12 13/1612 13/1612 11/1612 13/16
2 3/82 3/8
102 3/8
-10-
12 3/8
54545354
13 3/1613 3/1613 1/4
13 3/16
42 @ 792#12 @ 916#12 @ 837#
10 @ 1,035#124’ GLCSLX500-20 (S or AL)-124 Steel 30’ 2 13/16 7 1/8 18’-0” 27 1/4 20 7/8 28 3/8 12 13/16 2 3/8 14 3/8 54 13 3/16 10 @ 1,098#
*This column provides the total number of support hangers with the corresponding ver cal load applied by each support hanger (in pounds) based on the “L1” dimensions shown. Up to a 20” hanger drop will be provided by Gorbel. Addi onal hanger points or longer drops can be provided at an addi onal charge.
Gorbel® Ceiling Mounted Work Sta on Bridge Crane Kits include: bridge, runways, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Sway bracing is required on all systems except fl ush mounted systems (by others). Sway bracing kits are available but not included in the crane kit. Hoist provided by others.
Dimensions are for reference only and are subject to change without no ce.
CEILIN
G M
OU
NTED
WO
RK
STATION
BR
IDG
E CR
AN
ES
43
500# CAPACITYCEILING MOUNTED WORK STATION BRIDGE CRANES
BRIDGE LENGTH
(L)
RUNWAY LENGTH MODEL NUMBER TRACK
MATL.
BRIDGE RUNWAYMAX
L1T1in
L3in
L4
L6in
H3in
H3Ain
H4in
H2in
H1in
L7in
L8in
HANGERS(See Note)*
23’
23’GLC500-23 (S or AL)-23
GLCS500-23 (S or AL)-23AL500-23-23
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
21’-0”21’-0”21’-0”
14 15/1614 15/16
30 5/8
8 7/816 1/223 7/8
15 1/822 3/4
-
12 13/1612 13/1612 11/16
2 3/82 3/8
10
-10-
99
14
13 3/1613 3/1613 1/4
10 @ 803#4 @ 927#4 @ 841#
28’ GLCSL500-23 (S or AL)-28 Steel 25’ 2 13/16 7 1/8 21’-0” 14 15/16 18 7/8 25 1/8 12 13/16 2 3/8 12 3/8 9 13 3/16 4 @ 1,046#
33’GLC500-23 (S or AL)-33
GLCS500-23 (S or AL)-33AL500-23-33
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
21’-0”21’-0”21’-0”
14 15/1614 15/16
30 5/8
8 7/816 1/223 7/8
15 1/822 3/4
-
12 13/1612 13/1612 11/16
2 3/82 3/8
10
-10-
99
20
13 3/1613 3/1613 1/4
14 @ 803#6 @ 927#6 @ 841#
34’ GLCSLX500-23 (S or AL)-34 Steel 30’ 2 13/16 7 1/8 21’-0” 14 15/16 20 7/8 27 1/8 12 13/16 2 3/8 14 3/8 9 13 3/16 4 @ 1,109#
43’GLC500-23 (S or AL)-43
GLCS500-23 (S or AL)-43AL500-23-43
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
21’-0”21’-0”21’-0”
14 15/1614 15/16
30 5/8
8 7/816 1/223 7/8
15 1/822 3/4
-
12 13/1612 13/1612 11/16
2 3/82 3/8
10
-10-
131327
13 3/1613 3/1613 1/4
18 @ 803#6 @ 927#6 @ 841#
53’
GLC500-23 (S or AL)-53GLCS500-23 (S or AL)-53
AL500-23-53GLCSL500-23 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
2 13/162 13/162 11/162 13/16
7 1/87 1/8
7 3/167 1/8
21’-0”21’-0”21’-0”21’-0”
14 15/1614 15/16
30 5/814 15/16
8 7/816 1/223 7/818 7/8
15 1/822 3/4
-25 1/8
12 13/1612 13/1612 11/1612 13/16
2 3/82 3/8
102 3/8
-10-
12 3/8
13133013
13 3/1613 3/1613 1/4
13 3/16
22 @ 803#8 @ 927#8 @ 841#
6 @ 1,046#
63’GLC500-23 (S or AL)-63
GLCS500-23 (S or AL)-63AL500-23-63
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
21’-0”21’-0”21’-0”
14 15/1614 15/16
30 5/8
8 7/816 1/223 7/8
15 1/822 3/4
-
12 13/1612 13/1612 11/16
2 3/82 3/8
10
-10-
191937
13 3/1613 3/1613 1/4
26 @ 803#8 @ 927#8 @ 841#
64’ GLCSLX500-23 (S or AL)-64 Steel 30’ 2 13/16 7 1/8 21’-0” 30 9/16 20 7/8 27 1/8 12 13/16 2 3/8 14 3/8 46 13 3/16 6 @ 1,109#78’ GLCSL500-23 (S or AL)-78 Steel 25’ 2 13/16 7 1/8 21’-0” 30 9/16 18 7/8 25 1/8 12 13/16 2 3/8 12 3/8 54 13 3/16 8 @ 1,046#
83’GLC500-23 (S or AL)-83
GLCS500-23 (S or AL)-83AL500-23-83
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
7 1/87 1/8
7 3/16
21’-0”21’-0”21’-0”
30 9/1630 9/1630 5/8
8 7/816 1/223 7/8
15 1/822 3/4
-
12 13/1612 13/1612 11/16
2 3/82 3/8
10
-10-
545447
13 3/1613 3/1613 1/4
34 @ 803#10 @ 927#10 @ 841#
94’ GLCSLX-23 (S or AL)-94 Steel 30’ 2 13/16 7 1/8 21’-0” 30 9/16 20 7/8 27 1/8 12 13/16 2 3/8 14 3/8 54 13 3/16 8 @ 1,109#
103’
GLC500-23 (S or AL)-103GLCS500-23 (S or AL)-103
AL500-23-103GLCSL500-23 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
2 13/162 13/162 11/162 13/16
7 1/87 1/8
7 3/167 1/8
21’-0”21’-0”21’-0”21’-0”
30 9/1630 9/1630 5/8
30 9/16
8 7/816 1/223 7/818 7/8
15 1/822 3/4
-25 1/8
12 13/1612 13/1612 11/1612 13/16
2 3/82 3/8
102 3/8
-10-
12 3/8
54545354
13 3/1613 3/1613 1/4
13 3/16
42 @ 803#12 @ 927#12 @ 841#
10 @ 1,046#124’ GLCSLX500-23 (S or AL)-124 Steel 30’ 2 13/16 7 1/8 21’-0” 30 9/16 20 7/8 27 1/8 12 13/16 2 3/8 14 3/8 54 13 3/16 10 @ 1,109#
28’
23’GLC500-28 (S or AL)-23
GLCS500-28 (S or AL)-23AL500-28-23
SteelSteelAlum
6’20’20’
2 13/162 13/16
2 5/8
7 1/87 1/8
7 13/16
25’-0”25’-0”25’-0”
17 7/1617 7/16
38
10 11/1618 5/16
22 11/16
1522 5/8
-
15 3/1615 3/1613 1/8
2 3/82 3/8
10 1/2
-10-
99
14
23 5/1623 5/1623 3/8
10 @ 859#4 @ 983#4 @ 904#
28’ GLCSL500-28 (S or AL)-28 Steel 25’ 2 13/16 7 1/8 25’-0” 17 7/16 20 11/16 25 15 3/16 2 3/8 12 3/8 9 23 5/16 4 @ 1,102#
33’GLC500-28 (S or AL)-33
GLCS500-28 (S or AL)-33AL500-28-33
SteelSteelAlum
6’20’20’
2 13/162 13/16
2 5/8
7 1/87 1/8
7 13/16
25’-0”25’-0”25’-0”
17 7/1617 7/16
38
10 11/1618 5/16
22 11/16
1522 5/8
-
15 3/1615 3/1613 1/8
2 3/82 3/8
10 1/2
-10-
99
20
23 5/1623 5/1623 3/8
14 @ 859#6 @ 983#6 @ 904#
34’ GLCSLX500-28 (S or AL)-34 Steel 30’ 2 13/16 7 1/8 25’-0” 17 7/16 22 11/16 27 15 3/16 2 3/8 14 3/8 9 23 5/16 4 @ 1,165#
43’GLC500-28 (S or AL)-43
GLCS500-28 (S or AL)-43AL500-28-43
SteelSteelAlum
6’20’20’
2 13/162 13/16
2 5/8
7 1/87 1/8
7 13/16
25’-0”25’-0”25’-0”
17 7/1617 7/16
38
10 11/1618 5/16
22 11/16
1522 5/8
-
15 3/1615 3/1613 1/8
2 3/82 3/8
10 1/2
-10-
131327
23 5/1623 5/1623 3/8
18 @ 859#6 @ 983#6 @ 904#
53’
GLC500-28 (S or AL)-53GLCS500-28 (S or AL)-53
AL500-28-53GLCSL500-28 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
2 13/162 13/16
2 5/82 13/16
7 1/87 1/8
7 13/167 1/8
25’-0”25’-0”25’-0”25’-0”
17 7/1617 7/16
3817 7/16
10 11/1618 5/16
22 11/1620 11/16
1522 5/8
-25
15 3/1615 3/1613 1/8
15 3/16
2 3/82 3/8
10 1/22 3/8
-10-
12 3/8
13133013
23 5/1623 5/1623 3/8
23 5/16
22 @ 859#8 @ 983#8 @ 904#
6 @ 1,102#
63’GLC500-28 (S or AL)-63
GLCS500-28 (S or AL)-63AL500-28-63
SteelSteelAlum
6’20’20’
2 13/162 13/16
2 5/8
7 1/87 1/8
7 13/16
25’-0”25’-0”25’-0”
17 7/1617 7/16
38
10 11/1618 5/16
22 11/16
1522 5/8
-
15 3/1615 3/1613 1/8
2 3/82 3/8
10 1/2
-10-
191937
23 5/1623 5/1623 3/8
26 @ 859#8 @ 983#8 @ 904#
64’ GLCSLX500-28 (S or AL)-64 Steel 30’ 2 13/16 7 1/8 25’-0” 37 5/16 22 11/16 27 15 3/16 2 3/8 14 3/8 46 23 5/16 6 @ 1,165#78’ GLCSL500-28 (S or AL)-78 Steel 25’ 2 13/16 7 1/8 25’-0” 37 5/16 20 11/16 25 15 3/16 2 3/8 12 3/8 54 23 5/16 8 @ 1,102#
83’GLC500-28 (S or AL)-83
GLCS500-28 (S or AL)-83AL500-28-83
SteelSteelAlum
6’20’20’
2 13/162 13/16
2 5/8
7 1/87 1/8
7 13/16
25’-0”25’-0”25’-0”
37 5/1637 5/16
38
10 11/1618 5/16
22 11/16
1522 5/8
-
15 3/1615 3/1613 1/8
2 3/82 3/8
10 1/2
-10-
545447
23 5/1623 5/1623 3/8
34 @ 859#10 @ 983#10 @ 904#
94’ GLCSLX500-28 (S or AL)-94 Steel 30’ 2 13/16 7 1/8 25’-0” 37 5/16 22 11/16 27 15 3/16 2 3/8 14 3/8 54 23 5/16 8 @ 1,165#
103’
GLC500-28 (S or AL)-103GLCS500-28 (S or AL)-103
AL500-28-103GLCSL500-28 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
2 13/162 13/16
2 5/82 13/16
7 1/87 1/8
7 13/167 1/8
25’-0”25’-0”25’-0”25’-0”
37 5/1637 5/16
3837 5/16
10 11/1618 5/16
22 11/1620 11/16
1522 5/8
-25
15 3/1615 3/1613 1/8
15 3/16
2 3/82 3/8
10 1/22 3/8
-10-
12 3/8
54545354
23 5/1623 5/1623 3/8
23 5/16
42 @ 859#12 @ 983#12 @ 904#
10 @ 1,102#124’ GLCSLX500-28 (S or AL)-124 Steel 30’ 2 13/16 7 1/8 25’-0” 37 5/16 22 11/16 27 15 3/16 2 3/8 14 3/8 54 23 5/16 10 @ 1,165#
*This column provides the total number of support hangers with the corresponding ver cal load applied by each support hanger (in pounds) based on the “L1” dimensions shown. Up to a 20” hanger drop will be provided by Gorbel. Addi onal hanger points or longer drops can be provided at an addi onal charge.
Gorbel® Ceiling Mounted Work Sta on Bridge Crane Kits include: bridge, runways, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Sway bracing is required on all systems except fl ush mounted systems (by others). Sway bracing kits are available but not included in the crane kit. Hoist provided by others.
Dimensions are for reference only and are subject to change without no ce.
CEI
LIN
G M
OU
NTE
D W
OR
KST
ATIO
N B
RID
GE
CR
AN
ES
44
500# CAPACITYCEILING MOUNTED WORK STATION BRIDGE CRANES
BRIDGE LENGTH
(L)
RUNWAY LENGTH MODEL NUMBER TRACK
MATL.
BRIDGE RUNWAYMAX
L1T1in
L3in
L4
L6in
H3in
H3Ain
H4in
H2in
H1in
L7in
L8in
HANGERS(See Note)*
34’
28’ GLCSL500-15 (S or AL)-28 Steel 25’ 2 13/16 7 1/8 30’-0” 19 15/16 20 11/16 25 17 3/16 2 3/8 12 3/8 9 23 5/16 4 @ 1,133#
33’GLC500-15 (S or AL)-33
GLCS500-15 (S or AL)-33AL500-15-33
SteelSteelAlum
6’20’20’
2 13/162 13/16
2 5/8
7 1/87 1/8
7 13/16
30’-0”30’-0”30’-0”
19 15/1619 15/1644 11/16
10 11/1618 5/16
22 11/16
1522 5/8
-
17 3/1617 3/1615 1/4
2 3/82 3/8
12 5/8
-10-
99
20
23 5/1623 5/1623 3/8
14 @ 891#6 @ 1,014#
6 @ 935#34’ GLCSLX500-15 (S or AL)-34 Steel 30’ 2 13/16 7 1/8 30’-0” 19 15/16 22 11/16 27 17 3/16 2 3/8 14 3/8 9 23 5/16 4 @ 1,196#
43’GLC500-15 (S or AL)-43
GLCS500-15 (S or AL)-43AL500-15-43
SteelSteelAlum
6’20’20’
2 13/162 13/16
2 5/8
7 1/87 1/8
7 13/16
30’-0”30’-0”30’-0”
19 15/1619 15/1644 11/16
10 11/1618 5/16
22 11/16
1522 5/8
-
17 3/1617 3/1615 1/4
2 3/82 3/8
12 5/8
-10-
131327
23 5/1623 5/1623 3/8
18 @ 891#6 @ 1,014#
6 @ 935#
53’
GLC500-15 (S or AL)-53GLCS500-15 (S or AL)-53
AL500-15-53GLCSL500-15 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
2 13/162 13/16
2 5/82 13/16
7 1/87 1/8
7 13/167 1/8
30’-0”30’-0”30’-0”30’-0”
19 15/1619 15/1644 11/1619 15/16
10 11/1618 5/16
22 11/1620 11/16
1522 5/8
-25
17 3/1617 3/1615 1/4
17 3/16
2 3/82 3/8
12 5/82 3/8
-10-
12 3/8
13133013
23 5/1623 5/1623 3/8
23 5/16
22 @ 891#8 @ 1,014#
8 @ 935#6 @ 1,133#
63’GLC500-15 (S or AL)-63
GLCS500-15 (S or AL)-63AL500-15-63
SteelSteelAlum
6’20’20’
2 13/162 13/16
2 5/8
7 1/87 1/8
7 13/16
30’-0”30’-0”30’-0”
19 15/1619 15/1644 11/16
10 11/1618 5/16
22 11/16
1522 5/8
-
17 3/1617 3/1615 1/4
2 3/82 3/8
12 5/8
-10-
191937
23 5/1623 5/1623 3/8
26 @ 891#8 @ 1,014#
8 @ 935#64’ GLCSLX500-15 (S or AL)-64 Steel 30’ 2 13/16 7 1/8 30’-0” 44 22 11/16 27 17 3/16 2 3/8 14 3/8 46 23 5/16 6 @ 1,196#78’ GLCSL500-15 (S or AL)-78 Steel 25’ 2 13/16 7 1/8 30’-0” 44 20 11/16 25 17 3/16 2 3/8 12 3/8 54 23 5/16 8 @ 1,133#
83’GLC500-15 (S or AL)-83
GLCS500-15 (S or AL)-83AL500-15-83
SteelSteelAlum
6’20’20’
2 13/162 13/16
2 5/8
7 1/87 1/8
7 13/16
30’-0”30’-0”30’-0”
4444
44 11/16
10 11/1618 5/16
22 11/16
1522 5/8
-
17 3/1617 3/1615 1/4
2 3/82 3/8
12 5/8
-10-
545447
23 5/1623 5/1623 3/8
34 @ 891#10 @ 1,014#
10 @ 935#94’ GLCSLX-15 (S or AL)-94 Steel 30’ 2 13/16 7 1/8 30’-0” 44 22 11/16 27 17 3/16 2 3/8 14 3/8 54 23 5/16 8 @ 1,196#
103’
GLC500-15 (S or AL)-103GLCS500-15 (S or AL)-103
AL500-15-103GLCSL500-15 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
2 13/162 13/16
2 5/82 13/16
7 1/87 1/8
7 13/167 1/8
30’-0”30’-0”30’-0”30’-0”
4444
44 11/1644
10 11/1618 5/16
22 11/1620 11/16
1522 5/8
-25
17 3/1617 3/1615 1/4
17 3/16
2 3/82 3/8
12 5/82 3/8
-10-
12 3/8
54545354
23 5/1623 5/1623 3/8
23 5/16
42 @ 891#12 @ 1,041#
12 @ 935#10 @ 1,133#
124’ GLCSLX500-15 (S or AL)-124 Steel 30’ 2 13/16 7 1/8 30’-0” 44 22 11/16 27 17 3/16 2 3/8 14 3/8 54 23 5/16 10 @ 1,196#
*This column provides the total number of support hangers with the corresponding ver cal load applied by each support hanger (in pounds) based on the “L1” dimensions shown. Up to a 20” hanger drop will be provided by Gorbel. Addi onal hanger points or longer drops can be provided at an addi onal charge.
Gorbel® Ceiling Mounted Work Sta on Bridge Crane Kits include: bridge, runways, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Sway bracing is required on all systems except fl ush mounted systems (by others). Sway bracing kits are available but not included in the crane kit. Hoist provided by others.
Dimensions are for reference only and are subject to change without no ce.
CEILIN
G M
OU
NTED
WO
RK
STATION
BR
IDG
E CR
AN
ES
CEILING MOUNTED WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH MODEL NUMBER TRACK
MATL.
BRIDGE RUNWAYMAX
L1T1in
L3in
L4
L6in
H3in
H3Ain
H4in
H2in
H1in
L7in
L8in
HANGERS(See Note)*
8’
11’-6”GLC1000-8 (S or AL)-11.5
GLCS1000-8 (S or AL)-11.5AL1000-8-11.5
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
6’-6”6’-6”6’-6”
10 13/1610 13/16
13 1/2
10 3/1618 3/1622 1/16
14 1/822 1/8
-
7 5/87 5/87 3/4
3 1/163 1/165 1/8
-11 1/16
-
99
13
1515
14 15/16
6 @ 1,462#4 @ 1,670#4 @ 1,585#
23’GLC1000-8 (S or AL)-23
GLCS1000-8 (S or AL)-23AL1000-8-23
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
6’-6”6’-6”6’-6”
10 13/1610 13/16
13 1/2
10 3/1618 3/1622 1/16
14 1/822 1/8
-
7 5/87 5/87 3/4
3 1/163 1/165 1/8
-11 1/16
-
99
26
1515
14 15/16
10 @ 1,462#4 @ 1,670#4 @ 1585#
28’ GLCSL1000-8 (S or AL)-28 Steel 25’ 3 1/8 7 7/8 6’-6” 10 13/16 21 1/16 25 7 5/8 3 1/16 13 15/16 13 15 4 @ 1,777#
33’GLC1000-8 (S or AL)-33
GLCS1000-8 (S or AL)-33AL1000-8-33
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
6’-6”6’-6”6’-6”
10 13/1610 13/16
13 1/2
10 3/1618 3/1622 1/16
14 1/822 1/8
-
7 5/87 5/87 3/4
3 1/163 1/165 1/8
-11 1/16
-
131339
1515
14 15/16
14 @ 1,462#6 @ 1,670#6 @ 1,585#
34’ GLCSLX1000-8 (S or AL)-34 Steel 30’ 3 1/8 7 7/8 6’-6” 10 13/16 24 3/16 28 1/8 7 5/8 3 1/16 17 1/16 13 15 4 @ 1,949
43’GLC1000-8 (S or AL)-43
GLCS1000-8 (S or AL)-43AL1000-8-43
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
6’-6”6’-6”6’-6”
10 13/1610 13/16
13 1/2
10 3/1618 3/1622 1/16
14 1/822 1/8
-
7 5/87 5/87 3/4
3 1/163 1/165 1/8
-11 1/16
-
191949
1515
14 15/16
18 @ 1,462#6 @ 1,670#6 @ 1,585#
53’
GLC1000-8 (S or AL)-53GLCS1000-8 (S or AL)-53
AL1000-8-53GLCSL1000-8 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
3 1/83 1/82 5/83 1/8
7 7/87 7/8
7 13/167 7/8
6’-6”6’-6”6’-6”6’-6”
10 13/1610 13/16
13 1/210 13/16
10 3/1618 3/1622 1/1621 1/16
14 1/822 1/8
-25
7 5/87 5/87 3/47 5/8
3 1/163 1/165 1/8
3 1/16
-11 1/16
-13 15/16
19195319
1515
14 15/1615
22 @ 1,462#8 @ 1,670#8 @ 1,585#6 @ 1,777#
63’GLC1000-8 (S or AL)-63
GLCS1000-8 (S or AL)-63AL1000-8-63
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
6’-6”6’-6”6’-6”
10 13/1610 13/16
13 1/2
10 3/1618 3/1622 1/16
14 1/822 1/8
-
7 5/87 5/87 3/4
3 1/163 1/165 1/8
-11 1/16
-
262653
1515
14 15/16
26 @ 1,462#8 @ 1,670#8 @ 1,585#
64’ GLCSLX1000-8 (S or AL)-64 Steel 30’ 3 1/8 7 7/8 6’-6” 13 1/2 24 3/16 28 1/8 7 5/8 3 1/16 17 1/16 54 15 6 @ 1,949#78’ GLCSL1000-8 (S or AL)-78 Steel 25’ 3 1/8 7 7/8 6’-6” 13 1/2 21 1/16 25 7 5/8 3 1/16 13 15/16 54 15 8 @ 1,777#
83’GLC1000-8 (S or AL)-83
GLCS1000-8 (S or AL)-83AL1000-8-83
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
6’-6”6’-6”6’-6”
13 1/213 1/213 1/2
10 3/1618 3/1622 1/16
14 1/822 1/8
-
7 5/87 5/87 3/4
3 1/163 1/165 1/8
-11 1/16
-
545453
1515
14 15/16
34 @ 1,462#10 @ 1,670#10 @ 1,585#
94’ GLCSLX-8 (S or AL)-94 Steel 30’ 3 1/8 7 7/8 6’-6” 13 1/2 24 3/16 28 1/8 7 5/8 3 1/16 17 1/16 54 15 8 @ 1,949#
103’
GLC1000-8 (S or AL)-103GLCS1000-8 (S or AL)-103
AL1000-8-103GLCSL1000-8 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
3 1/83 1/82 5/83 1/8
7 7/87 7/8
7 13/167 7/8
6’-6”6’-6”6’-6”6’-6”
13 1/213 1/213 1/213 1/2
10 3/1618 3/1622 1/1621 1/16
14 1/822 1/8
-25
7 5/87 5/87 3/47 5/8
3 1/163 1/165 1/8
3 1/16
-11 1/16
-13 15/16
54545354
1515
14 15/1615
42 @ 1,462#12 @ 1,670#12 @ 1,585#10 @ 1,777#
124’ GLCSLX1000-8 (S or AL)-124 Steel 30’ 3 1/8 7 7/8 6’-6” 13 1/2 24 3/16 28 1/8 7 5/8 3 1/16 17 1/16 54 15 10 @ 1,949#
10’
11’-6”GLC1000-10 ( S or AL)-11.5
GLCS1000-10 (S or AL)-11.5AL1000-10-11.5
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
8’-0”8’-0”8’-0”
12 13/1612 13/16
16 7/8
10 3/1618 3/1622 1/16
14 1/822 1/8
-
7 5/87 5/8
13 1/8
3 1/163 1/1610 1/2
-11 1/16
-
99
13
1515
14 15/16
6 @ 1,468#4 @ 1,676#4 @ 1,604#
23’GLC1000-10 (S or AL)-23
GLCS1000-10 (S or AL)-23AL1000-10-23
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
8’-0”8’-0”8’-0”
12 13/1612 13/16
16 7/8
10 3/1618 3/1622 1/16
14 1/822 1/8
-
7 5/87 5/8
13 1/8
3 1/163 1/1610 1/2
-11 1/16
-
99
26
1515
14 15/16
10 @ 1,468#4 @ 1,676#4 @ 1,604#
28’ GLCSL1000-10 (S or AL)-28 Steel 25’ 3 1/8 7 7/8 8’-0” 12 13/16 21 1/16 25 7 5/8 3 1/16 13 15/16 13 15 4 @ 1,783#
33’GLC1000-10 (S or AL)-33
GLCS1000-10 (S or AL)-33AL1000-10-33
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
8’-0”8’-0”8’-0”
12 13/1612 13/16
16 7/8
10 3/1618 3/1622 1/16
14 1/822 1/8
-
7 5/87 5/8
13 1/8
3 1/163 1/1610 1/2
-11 1/16
-
131339
1515
14 15/16
14 @ 1,468#6 @ 1,676#6 @ 1,604#
34’ GLCSLX1000-10 (S or AL)-34 Steel 30’ 3 1/8 7 7/8 8’-0” 12 13/16 24 3/16 28 1/8 7 5/8 3 1/16 17 1/16 13 15 4 @ 1,955#
43’GLC1000-10 (S or AL)-43
GLCS1000-10 (S or AL)-43AL1000-10-43
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
8’-0”8’-0”8’-0”
12 13/1612 13/16
16 7/8
10 3/1618 3/1622 1/16
14 1/822 1/8
-
7 5/87 5/8
13 1/8
3 1/163 1/1610 1/2
-11 1/16
-
191949
1515
14 15/16
18 @ 1,468#6 @ 1,676#6 @ 1,604#
53’
GLC1000-10 (S or AL)-53GLCS1000-10 (S or AL)-53
AL1000-10-53GLCSL1000-10 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
3 1/83 1/82 5/83 1/8
7 7/87 7/8
7 13/167 7/8
8’-0”8’-0”8’-0”8’-0”
12 13/1612 13/16
16 7/812 13/16
10 3/1618 3/1622 1/1621 1/16
14 1/822 1/8
-25
7 5/87 5/8
13 1/87 5/8
3 1/163 1/1610 1/23 1/16
-11 1/16
-13 15/16
19195319
1515
14 15/1615
22 @ 1,468#8 @ 1,676#8 @ 1,604#6 @ 1,783#
63’GLC1000-10 (S or AL)-63
GLCS1000-10 (S or AL)-63AL1000-10-63
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
8’-0”8’-0”8’-0”
12 13/1612 13/16
16 7/8
10 3/1618 3/1622 1/16
14 1/822 1/8
-
7 5/87 5/8
13 1/8
3 1/163 1/1610 1/2
-11 1/16
-
262653
1515
14 15/16
26 @ 1,468#8 @ 1,676#8 @ 1,604#
64’ GLCSLX1000-10 (S or AL)-64 Steel 30’ 3 1/8 7 7/8 8’-0” 16 7/8 24 3/16 28 1/8 7 5/8 3 1/16 17 1/16 54 15 6 @ 1,955#78’ GLCSL1000-10 (S or AL)-78 Steel 25’ 3 1/8 7 7/8 8’-0” 16 7/8 21 1/16 25 7 5/8 3 1/16 13 15/16 54 15 8 @ 1,783#
83’GLC1000-10 (S or AL)-83
GLCS1000-10 (S or AL)-83AL1000-10-83
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
8’-0”8’-0”8’-0”
16 7/816 7/816 7/8
10 3/1618 3/1622 1/16
14 1/822 1/8
-
7 5/87 5/8
13 1/8
3 1/163 1/1610 1/2
-11 1/16
-
545453
1515
14 15/16
34 @ 1,468#10 @ 1,676#10 @ 1,604#
94’ GLCSLX1000-10 (S or AL)-94 Steel 30’ 3 1/8 7 7/8 8’-0” 16 7/8 24 3/16 28 1/8 7 5/8 3 1/16 17 1/16 54 15 8 @ 1,955#
103’
GLC1000-10 (S or AL)-103GLCS1000-10 (S or AL)-103
AL1000-10-103GLCSL1000-10 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
3 1/83 1/82 5/83 1/8
7 7/87 7/8
7 13/167 7/8
8’-0”8’-0”8’-0”8’-0”
16 7/816 7/816 7/816 7/8
10 3/1618 3/1622 1/1621 1/16
14 1/822 1/8
-25
7 5/87 5/8
13 1/87 5/8
3 1/163 1/1610 1/23 1/16
-11 1/16
-13 15/16
54545354
1515
14 15/1615
42 @ 1,468#12 @ 1,676#12 @ 1,604#10 @ 1,783#
124’ GLCSLX1000-10 (S or AL)-124 Steel 30’ 3 1/8 7 7/8 8’-0” 16 7/8 24 3/16 28 1/8 7 5/8 3 1/16 17 1/16 54 15 10 @ 1,955#
*This column provides the total number of support hangers with the corresponding ver cal load applied by each support hanger (in pounds) based on the “L1” dimensions shown. Up to a 20” hanger drop will be provided by Gorbel. Addi onal hanger points or longer drops can be provided at an addi onal charge.
Gorbel® Ceiling Mounted Work Sta on Bridge Crane Kits include: bridge, runways, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Sway bracing is required on all systems except fl ush mounted systems (by others). Sway bracing kits are available but not included in the crane kit. Hoist provided by others.
Dimensions are for reference only and are subject to change without no ce.
1000# CAPACITY
45
CEI
LIN
G M
OU
NTE
D W
OR
KST
ATIO
N B
RID
GE
CR
AN
ES
46
1000# CAPACITYCEILING MOUNTED WORK STATION BRIDGE CRANES
BRIDGE LENGTH
(L)
RUNWAY LENGTH MODEL NUMBER TRACK
MATL.
BRIDGE RUNWAYMAX
L1T1in
L3in
L4
L6in
H3in
H3Ain
H4in
H2in
H1in
L7in
L8in
HANGERS(See Note)*
15’
23’GLC1000-15 (S or AL)-23
GLCS1000-15 (S or AL)-23AL1000-15-23
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
13’-0”13’-0”13’-0”
16 13/1616 13/1623 9/16
10 3/1618 3/1622 1/16
14 1/822 1/8
-
14 1/814 1/813 1/8
3 1/163 1/1610 1/2
-11 1/16
-
99
26
1515
14 15/16
10 @ 1,517#4 @ 1,725#4 @ 1,626#
28’ GLCSL1000-15 (S or AL)-28 Steel 25’ 3 1/8 7 7/8 13’-0” 16 13/16 21 1/16 25 14 1/8 3 1/16 13 15/16 13 15 4 @ 1,832#
33’GLC1000-15 (S or AL)-33
GLCS1000-15 (S or AL)-33AL1000-15-33
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
13’-0”13’-0”13’-0”
16 13/1616 13/1623 9/16
10 3/1618 3/1622 1/16
14 1/822 1/8
-
14 1/814 1/813 1/8
3 1/163 1/1610 1/2
-11 1/16
-
131339
1515
14 15/16
14 @ 1,517#6 @ 1,725#6 @ 1,626#
34’ GLCSLX1000-15 (S or AL)-34 Steel 30’ 3 1/8 7 7/8 13’-0” 16 13/16 24 3/16 28 1/8 14 1/8 3 1/16 17 1/16 13 15 4 @ 2,004#
43’GLC1000-15 (S or AL)-43
GLCS1000-15 (S or AL)-43AL1000-15-43
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
13’-0”13’-0”13’-0”
16 13/1616 13/1623 9/16
10 3/1618 3/1622 1/16
14 1/822 1/8
-
14 1/814 1/813 1/8
3 1/163 1/1610 1/2
-11 1/16
-
191949
1515
14 15/16
18 @ 1,517#6 @ 1,725#6 @ 1,626#
53’
GLC1000-15 (S or AL)-53GLCS1000-15 (S or AL)-53
AL1000-15-53GLCSL1000-15 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
3 1/83 1/82 5/83 1/8
7 7/87 7/8
7 13/167 7/8
13’-0”13’-0”13’-0”13’-0”
16 13/1616 13/1623 9/16
16 13/16
10 3/1618 3/1622 1/1622 1/16
14 1/822 1/8
-25
14 1/814 1/813 1/814 1/8
3 1/163 1/1610 1/23 1/16
-11 1/16
-13 15/16
19195319
1515
14 15/1615
22 @ 1,517#8 @ 1,725#8 @ 1,626#6 @ 1,832#
63’GLC1000-15 (S or AL)-63
GLCS1000-15 (S or AL)-63AL1000-15-63
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
13’-0”13’-0”13’-0”
16 13/1616 13/1623 9/16
10 3/1618 3/1622 1/16
14 1/822 1/8
-
14 1/814 1/813 1/8
3 1/163 1/1610 1/2
-11 1/16
-
262653
1515
14 15/16
26 @ 1,517#8 @ 1,725#8 @ 1,626#
64’ GLCSLX1000-15 (S or AL)-64 Steel 30’ 3 1/8 7 7/8 13’-0” 23 9/16 24 3/16 28 1/8 14 1/8 3 1/16 17 1/16 54 15 6 @ 2,004#78’ GLCSL1000-15 (S or AL)-78 Steel 25’ 3 1/8 7 7/8 13’-0” 23 9/16 22 1/16 25 14 1/8 3 1/16 13 15/16 54 15 8 @ 1,832#
83’GLC1000-15 (S or AL)-83
GLCS1000-15 (S or AL)-83AL1000-15-83
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
13’-0”13’-0”13’-0”
23 9/1623 9/1623 9/16
10 3/1618 3/1622 1/16
14 1/822 1/8
-
14 1/814 1/813 1/8
3 1/163 1/1610 1/2
-11 1/16
-
545453
1515
14 15/16
34 @ 1,517#10 @ 1,725#10 @ 1,626#
94’ GLCSLX-15 (S or AL)-94 Steel 30’ 3 1/8 7 7/8 13’-0” 23 9/16 24 3/16 28 1/8 14 1/8 3 1/16 17 1/16 54 15 8 @ 2,004#
103’
GLC1000-15 (S or AL)-103GLCS1000-15 (S or AL)-103
AL1000-15-103GLCSL1000-15 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
3 1/83 1/82 5/83 1/8
7 7/87 7/8
7 13/167 7/8
13’-0”13’-0”13’-0”13’-0”
23 9/1623 9/1623 9/1623 9/16
10 3/1618 3/1622 1/1621 1/16
14 1/822 1/8
-25
14 1/814 1/813 1/814 1/8
3 1/163 1/1610 1/23 1/16
-11 1/16
-13 15/16
54545354
1515
14 15/1615
42 @ 1,517#12 @ 1,725#12 @ 1,626#10 @ 1,832#
124’ GLCSLX1000-15 (S or AL)-124 Steel 30’ 3 1/8 7 7/8 13’-0” 23 9/16 24 3/16 28 1/8 14 1/8 3 1/16 17 1/16 54 15 10 @ 2,004#
20’
23’GLC1000-20 (S or AL)-23
GLCS1000-20 (S or AL)-23AL1000-20-23
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
18’-0”18’-0”18’-0”
18 13/1618 13/1626 15/16
10 3/1618 3/1622 1/16
14 1/822 1/8
-
14 1/814 1/813 1/8
3 1/163 1/1610 1/2
-11 1/16
-
99
26
1515
14 15/16
10 @ 1,548#4 @ 1,756#4 @ 1,648#
28’ GLCSL1000-20 (S or AL)-28 Steel 25’ 3 1/8 7 7/8 18’-0” 18 13/16 21 1/16 25 14 1/8 3 1/16 13 15/16 13 15 4 @ 1,863#
33’GLC1000-20 (S or AL)-33
GLCS1000-20 (S or AL)-33AL1000-20-33
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
18’-0”18’-0”18’-0”
18 13/1618 13/1626 15/16
10 3/1618 3/1622 1/16
14 1/822 1/8
-
14 1/814 1/813 1/8
3 1/163 1/1610 1/2
-11 1/16
-
131339
1515
14 15/16
14 @ 1,548#6 @ 1,756#6 @ 1,648#
34’ GLCSLX1000-20 (S or AL)-34 Steel 30’ 3 1/8 7 7/8 18’-0” 18 13/16 24 3/16 28 1/8 14 1/8 3 1/16 17 1/16 13 15 4 @ 2,035#
43’GLC1000-20 (S or AL)-43
GLCS1000-20 (S or AL)-43AL1000-20-43
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
18’-0”18’-0”18’-0”
18 13/1618 13/1626 15/16
10 3/1618 3/1622 1/16
14 1/822 1/8
-
14 1/814 1/813 1/8
3 1/163 1/1610 1/2
-11 1/16
-
191949
1515
14 15/16
18 @ 1,548#6 @ 1,756#6 @ 1,648#
53’
GLC1000-20 (S or AL)-53GLCS1000-20 (S or AL)-53
AL1000-20-53GLCSL1000-20 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
3 1/83 1/82 5/83 1/8
7 7/87 7/8
7 13/167 7/8
18’-0”18’-0”18’-0”18’-0”
18 13/1618 13/1626 15/1618 13/16
10 3/1618 3/1622 1/1621 1/16
14 1/822 1/8
-25
14 1/814 1/813 1/814 1/8
3 1/163 1/1610 1/23 1/16
-11 1/16
-13 15/16
19195319
1515
14 15/1615
22 @ 1,548#8 @ 1,756#8 @ 1,648#6 @ 1,863#
63’GLC1000-20 (S or AL)-63
GLCS1000-20 (S or AL)-63AL1000-20-63
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
18’-0”18’-0”18’-0”
18 13/1618 13/1626 15/16
10 3/1618 3/1622 1/16
14 1/822 1/8
-
14 1/814 1/813 1/8
3 1/163 1/1610 1/2
-11 1/16
-
262653
1515
14 15/16
26 @ 1,548#8 @ 1,756#8 @ 1,648#
64’ GLCSLX1000-20 (S or AL)-64 Steel 30’ 3 1/8 7 7/8 18’-0” 26 15/16 24 3/16 28 1/8 14 1/8 3 1/16 17 1/16 54 15 6 @ 2,035#78’ GLCSL1000-20 (S or AL)-78 Steel 25’ 3 1/8 7 7/8 18’-0” 26 15/16 21 1/16 25 14 1/8 3 1/16 13 15/16 54 15 8 @ 1,863#
83’GLC1000-20 (S or AL)-83
GLCS1000-20 (S or AL)-83AL1000-20-83
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
18’-0”18’-0”18’-0”
26 15/1626 15/1626 15/16
10 3/1618 3/1622 1/16
14 1/822 1/8
-
14 1/814 1/813 1/8
3 1/163 1/1610 1/2
-11 1/16
-
545453
1515
14 15/16
34 @ 1,548#10 @ 1,756#10 @ 1,648#
94’ GLCSLX1000-20 (S or AL)-94 Steel 30’ 3 1/8 7 7/8 18’-0” 26 15/16 24 3/16 28 1/8 14 1/8 3 1/16 17 1/16 54 15 8 @ 2,035#
103’
GLC1000-20 (S or AL)-103GLCS1000-20 (S or AL)-103
AL1000-20-103GLCSL1000-20 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
3 1/83 1/82 5/83 1/8
7 7/87 7/8
7 13/167 7/8
18’-0”18’-0”18’-0”18’-0”
26 15/1626 15/1626 15/1626 15/16
10 3/1618 3/1622 1/1621 1/16
14 1/822 1/8
-25
14 1/814 1/813 1/814 1/8
3 1/163 1/1610 1/23 1/16
-11 1/16
-13 15/16
54545354
1515
14 15/1615
42 @ 1,548#12 @ 1,756#12 @ 1,648#10 @ 1,863#
124’ GLCSLX1000-20 (S or AL)-124 Steel 30’ 3 1/8 7 7/8 18’-0” 26 15/16 24 3/16 28 1/8 14 1/8 3 1/16 17 1/16 54 15 10 @ 2,035#
*This column provides the total number of support hangers with the corresponding ver cal load applied by each support hanger (in pounds) based on the “L1” dimensions shown. Up to a 20” hanger drop will be provided by Gorbel. Addi onal hanger points or longer drops can be provided at an addi onal charge.
Gorbel® Ceiling Mounted Work Sta on Bridge Crane Kits include: bridge, runways, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Sway bracing is required on all systems except fl ush mounted systems (by others). Sway bracing kits are available but not included in the crane kit. Hoist provided by others.
Dimensions are for reference only and are subject to change without no ce.
CEILIN
G M
OU
NTED
WO
RK
STATION
BR
IDG
E CR
AN
ES
47
1000# CAPACITYCEILING MOUNTED WORK STATION BRIDGE CRANES
BRIDGE LENGTH
(L)
RUNWAY LENGTH MODEL NUMBER TRACK
MATL.
BRIDGE RUNWAYMAX
L1T1in
L3in
L4
L6in
H3in
H3Ain
H4in
H2in
H1in
L7in
L8in
HANGERS(See Note)*
23’
23’GLC1000-23 (S or AL)-23
GLCS1000-23 (S or AL)-23AL1000-23-23
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
21’-0”21’-0”20’-0”
20 13/1620 13/16
30 1/4
10 3/1618 3/1622 1/16
15 11/1623 11/16
-
14 1/814 1/813 1/8
3 1/163 1/1610 1/2
-11 1/16
-
99
26
1515
14 15/16
10 @ 1,566#4 @ 1,774#4 @ 1,656#
28’ GLCSL1000-23 (S or AL)-28 Steel 25’ 3 1/8 7 7/8 21’-0” 20 13/16 21 1/16 26 9/16 14 1/8 3 1/16 13 15/16 13 15 4 @ 1,881#
33’GLC1000-23 (S or AL)-33
GLCS1000-23 (S or AL)-33AL1000-23-33
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
21’-0”21’-0”20’-0”
20 13/1620 13/16
30 1/4
10 3/1618 3/1622 1/16
15 11/1623 11/16
-
14 1/814 1/813 1/8
3 1/163 1/1610 1/2
-11 1/16
-
131339
1515
14 15/16
14 @ 1,566#6 @ 1,774#6 @ 1,656#
34’ GLCSLX1000-23 (S or AL)-34 Steel 30’ 3 1/8 7 7/8 21’-0” 20 13/16 24 3/16 29 11/16 14 1/8 3 1/16 17 1/16 13 15 4 @ 2,053#
43’GLC1000-23 (S or AL)-43
GLCS1000-23 (S or AL)-43AL1000-23-43
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
21’-0”21’-0”20’-0”
20 13/1620 13/16
30 1/4
10 3/1618 3/1622 1/16
15 11/1623 11/16
-
14 1/814 1/813 1/8
3 1/163 1/1610 1/2
-11 1/16
-
191949
1515
14 15/16
18 @ 1,566#6 @ 1,774#6 @ 1,656#
53’
GLC1000-23 (S or AL)-53GLCS1000-23 (S or AL)-53
AL1000-23-53GLCSL1000-23 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
3 1/83 1/82 5/83 1/8
7 7/87 7/8
7 13/167 7/8
21’-0”21’-0”20’-0”21’-0”
20 13/1620 13/16
30 1/420 13/16
10 3/1618 3/1622 1/1621 1/16
15 11/1623 11/16
-26 9/16
14 1/814 1/813 1/814 1/8
3 1/163 1/1610 1/23 1/16
-11 1/16
-13 15/16
19195319
1515
14 15/1615
22 @ 1,566#8 @ 1,774#8 @ 1,656#6 @ 1,881#
63’GLC1000-23 (S or AL)-63
GLCS1000-23 (S or AL)-63AL1000-23-63
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
21’-0”21’-0”20’-0”
20 13/1620 13/16
30 1/4
10 3/1618 3/1622 1/16
15 11/1623 11/16
-
14 1/814 1/813 1/8
3 1/163 1/1610 1/2
-11 1/16
-
262653
1515
14 15/16
26 @ 1,566#8 @ 1,774#8 @ 1,656#
64’ GLCSLX1000-23 (S or AL)-64 Steel 30’ 3 1/8 7 7/8 21’-0” 30 1/4 24 3/16 29 11/16 14 1/8 3 1/16 17 1/16 54 15 6 @ 2,053#78’ GLCSL1000-23 (S or AL)-78 Steel 25’ 3 1/8 7 7/8 21’-0” 30 1/4 21 1/16 26 9/16 14 1/8 3 1/16 13 15/16 54 15 8 @ 1,881#
83’GLC1000-23 (S or AL)-83
GLCS1000-23 (S or AL)-83AL1000-23-83
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
21’-0”21’-0”20’-0”
30 1/430 1/430 1/4
10 3/1618 3/1622 1/16
15 11/1623 11/16
-
14 1/814 1/813 1/8
3 1/163 1/1610 1/2
-11 1/16
-
545453
1515
14 15/16
34 @ 1,566#10 @ 1,774#10 @ 1,656#
94’ GLCSLX-23 (S or AL)-94 Steel 30’ 3 1/8 7 7/8 21’-0” 30 1/4 24 3/16 29 11/16 14 1/8 3 1/16 17 1/16 54 15 8 @ 2,053#
103’
GLC1000-23 (S or AL)-103GLCS1000-23 (S or AL)-103
AL1000-23-103GLCSL1000-23 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
3 1/83 1/82 5/83 1/8
7 7/87 7/8
7 13/167 7/8
21’-0”21’-0”20’-0”21’-0”
30 1/430 1/430 1/430 1/4
10 3/1618 3/1622 1/1621 1/16
15 11/1623 11/16
-26 9/16
14 1/814 1/813 1/814 1/8
3 1/163 1/1610 1/23 1/16
-11 1/16
-13 15/16
54545354
1515
14 15/1615
42 @ 1,566#12 @ 1,774#12 @ 1,656#10 @ 1,881#
124’ GLCSLX1000-23 (S or AL)-124 Steel 30’ 3 1/8 7 7/8 21’-0” 30 1/4 24 3/16 29 11/16 14 1/8 3 1/16 17 1/16 54 15 10 @ 2,053#
28’
23’GLC1000-28 (S or AL)-23
GLCS1000-28 (S or AL)-23AL1000-28-23
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
25’-0”25’-0”25’-0”
24 13/1624 13/16
37
12 7/1620 7/1623 5/8
15 11/1623 11/16
-
1717
15 1/4
3 1/163 1/1612 5/8
-11 1/16
-
99
26
21 1/1621 1/16
21
10 @ 1,614#4 @ 1,821#4 @ 1,686#
28’ GLCSL1000-28 (S or AL)-28 Steel 25’ 3 1/8 7 7/8 25’-0” 24 13/16 23 5/16 26 9/16 17 3 1/16 13 15/16 13 21 1/16 4 @ 1,928#
33’GLC1000-28 (S or AL)-33
GLCS1000-28 (S or AL)-33AL1000-28-33
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
25’-0”25’-0”25’-0”
24 13/1624 13/16
37
12 7/1620 7/1623 5/8
15 11/1623 11/16
-
1717
15 1/4
3 1/163 1/1612 5/8
-11 1/16
-
131330
21 1/1621 1/16
21
14 @ 1,614#6 @ 1,821#6 @ 1,686#
34’ GLCSLX1000-28 (S or AL)-34 Steel 30’ 3 1/8 7 7/8 25’-0” 24 13/16 26 7/16 29 11/16 17 3 1/16 17 1/16 13 21 1/16 4 @ 2,100#
43’GLC1000-28 (S or AL)-43
GLCS1000-28 (S or AL)-43AL1000-28-43
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
25’-0”25’-0”25’-0”
24 13/1624 13/16
37
12 7/1620 7/1623 5/8
15 11/1623 11/16
-
1717
15 1/4
3 1/163 1/1612 5/8
-11 1/16
-
191949
21 1/1621 1/16
21
18 @ 1,614#6 @ 1,821#6 @ 1,686#
53’
GLC1000-28 (S or AL)-53GLCS1000-28 (S or AL)-53
AL1000-28-53GLCSL1000-28 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
3 1/83 1/82 5/83 1/8
7 7/87 7/8
7 13/167 7/8
25’-0”25’-0”25’-0”25’-0”
24 13/1624 13/16
3724 13/16
12 7/1620 7/1623 5/8
23 5/16
15 11/1623 11/16
-26 9/16
1717
15 1/417
3 1/163 1/1612 5/83 1/16
-11 1/16
-13 15/16
19195319
21 1/1621 1/16
2121 1/16
22 @ 1,614#8 @ 1,821#8 @ 1,686#6 @ 1,928#
63’GLC1000-28 (S or AL)-63
GLCS1000-28 (S or AL)-63AL1000-28-63
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
25’-0”25’-0”25’-0”
24 13/1624 13/16
37
12 7/1620 7/1623 5/8
15 11/1623 11/16
-
1717
15 1/4
3 1/163 1/1612 5/8
-11 1/16
-
262653
21 1/1621 1/16
21
26 @ 1,614#8 @ 1,821#8 @ 1,686#
64’ GLCSLX1000-28 (S or AL)-64 Steel 30’ 3 1/8 7 7/8 25’-0” 37 26 7/16 29 11/16 17 3 1/16 17 1/16 54 21 1/16 6 @ 2,100#78’ GLCSL1000-28 (S or AL)-78 Steel 25’ 3 1/8 7 7/8 25’-0” 37 23 5/16 26 9/16 17 3 1/16 13 15/16 54 21 1/16 8 @ 1,928#
83’GLC1000-28 (S or AL)-83
GLCS1000-28 (S or AL)-83AL1000-28-83
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
25’-0”25’-0”25’-0”
373737
12 7/1620 7/1623 5/8
15 11/1623 11/16
-
1717
15 1/4
3 1/163 1/1612 5/8
-11 1/16
-
545453
21 1/1621 1/16
21
34 @ 1,614#10 @ 1,821#10 @ 1,686#
94’ GLCSLX1000-28 (S or AL)-94 Steel 30’ 3 1/8 7 7/8 25’-0” 37 26 7/16 29 11/16 17 3 1/16 17 1/16 54 21 1/16 8 @ 2,100#
103’
GLC1000-28 (S or AL)-103GLCS1000-28 (S or AL)-103
AL1000-28-103GLCSL1000-28 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
3 1/83 1/82 5/83 1/8
7 7/87 7/8
7 13/167 7/8
25’-0”25’-0”25’-0”25’-0”
37373737
12 7/1620 7/1623 5/8
23 5/16
15 11/1623 11/16
-26 9/16
1717
15 1/417
3 1/163 1/1612 5/83 1/16
-11 1/16
-13 15/16
54545354
21 1/1621 1/16
2121 1/16
42 @ 1,614#12 @ 1,821#12 @ 1,686#10 @ 1,928#
124’ GLCSLX1000-28 (S or AL)-124 Steel 30’ 3 1/8 7 7/8 25’-0” 37 26 7/16 29 11/16 17 3 1/16 17 1/16 54 21 1/16 10 @ 2,100#
*This column provides the total number of support hangers with the corresponding ver cal load applied by each support hanger (in pounds) based on the “L1” dimensions shown. Up to a 20” hanger drop will be provided by Gorbel. Addi onal hanger points or longer drops can be provided at an addi onal charge.
Gorbel® Ceiling Mounted Work Sta on Bridge Crane Kits include: bridge, runways, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Sway bracing is required on all systems except fl ush mounted systems (by others). Sway bracing kits are available but not included in the crane kit. Hoist provided by others.
Dimensions are for reference only and are subject to change without no ce.
CEI
LIN
G M
OU
NTE
D W
OR
KST
ATIO
N B
RID
GE
CR
AN
ES
48
1000# CAPACITYCEILING MOUNTED WORK STATION BRIDGE CRANES
BRIDGE LENGTH
(L)
RUNWAY LENGTH MODEL NUMBER TRACK
MATL.
BRIDGE RUNWAYMAX
L1T1in
L3in
L4
L6in
H3in
H3Ain
H4in
H2in
H1in
L7in
L8in
HANGERS(See Note)*
34’
28’ GLCSL1000-15 (S or AL)-28 Steel 25’ 3 1/8 7 7/8 30’-0” 28 13/16 23 5/16 26 9/16 20 1/8 3 1/16 13 15/16 13 21 1/16 4 @ 2,014#
33’GLC1000-15 (S or AL)-33
GLCS1000-15 (S or AL)-33AL1000-15-33
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
30’-0”30’-0”30’-0”
28 13/1628 13/1643 13/16
12 7/1620 7/1623 5/8
15 11/1623 11/16
-
20 1/820 1/816 3/4
3 1/163 1/1614 1/8
-11 1/16
-
131339
21 1/1621 1/16
21
14 @ 1,700#6 @ 1,907#6 @ 1,732#
34’ GLCSLX1000-15 (S or AL)-34 Steel 30’ 3 1/8 7 7/8 30’-0” 28 13/16 26 7/16 29 11/16 20 1/8 3 1/16 17 1/16 13 21 1/16 4 @ 2,187#
43’GLC1000-15 (S or AL)-43
GLCS1000-15 (S or AL)-43AL1000-15-43
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
30’-0”30’-0”30’-0”
28 13/1628 13/1643 13/16
12 7/1620 7/1623 5/8
15 11/1623 11/16
-
20 1/820 1/816 3/4
3 1/163 1/1614 1/8
-11 1/16
-
191949
21 1/1621 1/16
21
18 @ 1,700#6 @ 1,907#6 @ 1,732#
53’
GLC1000-15 (S or AL)-53GLCS1000-15 (S or AL)-53
AL1000-15-53GLCSL1000-15 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
3 1/83 1/82 5/83 1/8
7 7/87 7/8
7 13/167 7/8
30’-0”30’-0”30’-0”30’-0”
28 13/1628 13/1643 13/1628 13/16
12 7/1620 7/1623 5/8
23 5/16
15 11/1623 11/16
-26 9/16
20 1/820 1/816 3/420 1/8
3 1/163 1/1614 1/83 1/16
-11 1/16
-13 15/16
19195319
21 1/1621 1/16
2121 1/16
22 @ 1,700#8 @ 1,907#8 @ 1,732#6 @ 2,014#
63’GLC1000-15 (S or AL)-63
GLCS1000-15 (S or AL)-63AL1000-15-63
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
30’-0”30’-0”30’-0”
28 13/1628 13/1643 13/16
12 7/1620 7/1623 5/8
15 11/1623 11/16
-
20 1/820 1/816 3/4
3 1/163 1/1614 1/8
-11 1/16
-
262653
21 1/1621 1/16
21
26 @ 1,700#8 @ 1,907#8 @ 1,732#
64’ GLCSLX1000-15 (S or AL)-64 Steel 30’ 3 1/8 7 7/8 30’-0” 43 13/16 26 7/16 29 11/16 20 1/8 3 1/16 17 1/16 54 21 1/16 6 @ 2,187#78’ GLCSL1000-15 (S or AL)-78 Steel 25’ 3 1/8 7 7/8 30’-0” 43 13/16 23 5/16 26 9/16 20 1/8 3 1/16 13 15/16 54 21 1/16 8 @ 2,014#
83’GLC1000-15 (S or AL)-83
GLCS1000-15 (S or AL)-83AL1000-15-83
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
7 7/87 7/8
7 13/16
30’-0”30’-0”30’-0”
43 13/1643 13/1643 13/16
12 7/1620 7/1623 5/8
15 11/1623 11/16
-
20 1/820 1/816 3/4
3 1/163 1/1614 1/8
-11 1/16
-
545453
21 1/1621 1/16
21
34 @ 1,700#10 @ 1,907#10 @ 1,732#
94’ GLCSLX-15 (S or AL)-94 Steel 30’ 3 1/8 7 7/8 30’-0” 43 13/16 26 7/16 29 11/16 20 1/8 3 1/16 17 1/16 54 21 1/16 8 @ 2,187#
103’
GLC1000-15 (S or AL)-103GLCS1000-15 (S or AL)-103
AL1000-15-103GLCSL1000-15 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
3 1/83 1/82 5/83 1/8
7 7/87 7/8
7 13/167 7/8
30’-0”30’-0”30’-0”30’-0”
43 13/1643 13/1643 13/1643 13/16
12 7/1620 7/1623 5/8
23 5/16
15 11/1623 11/16
-26 9/16
20 1/820 1/816 3/420 1/8
3 1/163 1/1614 1/83 1/16
-11 1/16
-13 15/16
54545354
21 1/1621 1/16
2121 1/16
42 @ 1,700#12 @ 1,907#12 @ 1,732#10 @ 2,014#
124’ GLCSLX1000-15 (S or AL)-124 Steel 30’ 3 1/8 7 7/8 30’-0” 43 13/16 26 7/16 29 11/16 20 1/8 3 1/16 17 1/16 54 21 1/16 10 @ 2,187#
*This column provides the total number of support hangers with the corresponding ver cal load applied by each support hanger (in pounds) based on the “L1” dimensions shown. Up to a 20” hanger drop will be provided by Gorbel. Addi onal hanger points or longer drops can be provided at an addi onal charge.
Gorbel® Ceiling Mounted Work Sta on Bridge Crane Kits include: bridge, runways, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Sway bracing is required on all systems except fl ush mounted systems (by others). Sway bracing kits are available but not included in the crane kit. Hoist provided by others.
Dimensions are for reference only and are subject to change without no ce.
CEILIN
G M
OU
NTED
WO
RK
STATION
BR
IDG
E CR
AN
ES
CEILING MOUNTED WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH MODEL NUMBER TRACK
MATL.
BRIDGE RUNWAYMAX
L1T1in
L3in
L4
L6in
H3in
H3Ain
H4in
H2in
H1in
L7in
L8in
HANGERS(See Note)*
8’
11’-6”GLC2000-8 (S or AL)-11.5
GLCS2000-8 (S or AL)-11.5AL2000-8-11.5
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
6’-6”6’-6”6’-6”
1111
13 11/16
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
8 7/88 7/8
8 1/16
3 1/23 1/25 5/8
-12-
99
13
16 1/1616 1/16
16 15/16
6 @ 2,902#4 @ 3,185#4 @ 3,026#
23’GLC2000-8 (S or AL)-23
GLCS2000-8 (S or AL)-23AL2000-8-23
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
6’-6”6’-6”6’-6”
1111
13 11/16
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
8 7/88 7/8
8 1/16
3 1/23 1/25 5/8
-12-
99
26
16 1/1616 1/16
16 15/16
10 @ 2,902#4 @ 3,185#4 @ 3,026#
28’ GLCSL2000-8 (S or AL)-28 Steel 25’ 2 7/8 8 1/16 6’-6” 11 23 27 7/16 8 7/8 3 1/2 15 3/8 13 16 1/16 4 @ 3,331#
33’GLC2000-8 (S or AL)-33
GLCS2000-8 (S or AL)-33AL2000-8-33
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
6’-6”6’-6”6’-6”
1111
13 11/16
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
8 7/88 7/8
8 1/16
3 1/23 1/25 5/8
-12-
131339
16 1/1616 1/16
16 15/16
14 @ 2,902#6 @ 3,185#6 @ 3,026#
34’ GLCSLX2000-8 (S or AL)-34 Steel 30’ 2 7/8 8 1/16 6’-6” 11 25 5/8 30 1/16 8 7/8 3 1/2 18 13 16 1/16 4 @ 3,451#
43’GLC2000-8 (S or AL)-43
GLCS2000-8 (S or AL)-43AL2000-8-43
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
6’-6”6’-6”6’-6”
1111
13 11/16
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
8 7/88 7/8
8 1/16
3 1/23 1/25 5/8
-12-
191949
16 1/1616 1/16
16 15/16
18 @ 2,902#6 @ 3,185#6 @ 3,026#
53’
GLC2000-8 (S or AL)-53GLCS2000-8 (S or AL)-53
AL2000-8-53GLCSL2000-8 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
2 7/82 7/82 3/82 7/8
8 1/168 1/16
88 1/16
6’-6”6’-6”6’-6”6’-6”
1111
13 11/1611
11 1/819 5/8
25 5/1623
15 9/1624 1/16
-27 7/16
8 7/88 7/8
8 1/168 7/8
3 1/23 1/25 5/83 1/2
-12-
15 3/8
19195319
16 1/1616 1/16
16 15/1616 1/16
22 @ 2,902#8 @ 3,185#8 @ 3,026#6 @ 3,331#
63’GLC2000-8 (S or AL)-63
GLCS2000-8 (S or AL)-63AL2000-8-63
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
6’-6”6’-6”6’-6”
1111
13 11/16
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
8 7/88 7/8
8 1/16
3 1/23 1/25 5/8
-12-
262653
16 1/1616 1/16
16 15/16
26 @ 2,902#8 @ 3,185#8 @ 3,026#
64’ GLCSLX2000-8 (S or AL)-64 Steel 30’ 2 7/8 8 1/16 6’-6” 13 11/16 25 5/8 30 1/16 8 7/8 3 1/2 18 54 16 1/16 6 @ 3,451#78’ GLCSL2000-8 (S or AL)-78 Steel 25’ 2 7/8 8 1/16 6’-6” 13 11/16 23 27 7/16 8 7/8 3 1/2 15 3/8 54 16 1/16 8 @ 3,331#
83’GLC2000-8 (S or AL)-83
GLCS2000-8 (S or AL)-83AL2000-8-83
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
6’-6”6’-6”6’-6”
13 11/1613 11/1613 11/16
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
8 7/88 7/8
8 1/16
3 1/23 1/25 5/8
-12-
545453
16 1/1616 1/16
16 15/16
34 @ 2,902#10 @ 3,185#10 @ 3,026#
94’ GLCSLX-8 (S or AL)-94 Steel 30’ 2 7/8 8 1/16 6’-6” 13 11/16 25 5/8 30 1/16 8 7/8 3 1/2 18 54 16 1/16 8 @ 3,451#
103’
GLC2000-8 (S or AL)-103GLCS2000-8 (S or AL)-103
AL2000-8-103GLCSL2000-8 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
2 7/82 7/82 3/82 7/8
8 1/168 1/16
88 1/16
6’-6”6’-6”6’-6”6’-6”
13 11/1613 11/1613 11/1613 11/16
11 1/819 5/8
25 5/1623
15 9/1624 1/16
-27 7/16
8 7/88 7/8
8 1/168 7/8
3 1/23 1/25 5/83 1/2
-12-
15 3/8
54545354
16 1/1616 1/16
16 15/1616 1/16
42 @ 2,902#12 @ 3,185#12 @ 3,026#10 @ 3,331#
124’ GLCSLX2000-8 (S or AL)-124 Steel 30’ 2 7/8 8 1/16 6’-6” 13 11/16 25 5/8 30 1/16 8 7/8 3 1/2 18 54 16 1/16 10 @ 3,451#
10’
11’-6”GLC2000-10 ( S or AL)-11.5
GLCS2000-10 (S or AL)-11.5AL2000-10-11.5
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
8’-0”8’-0”8’-0”
1313
17 1/16
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
8 7/88 7/8
13 3/8
3 1/23 1/2
11
-12-
99
13
16 1/1616 1/16
16 15/16
6 @ 2,913#4 @ 3,196#4 @ 3,046#
23’GLC2000-10 (S or AL)-23
GLCS2000-10 (S or AL)-23AL2000-10-23
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
8’-0”8’-0”8’-0”
1313
17 1/16
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
8 7/88 7/8
13 3/8
3 1/23 1/2
11
-12-
99
26
16 1/1616 1/16
16 15/16
10 @ 2,913#4 @ 3,196#4 @ 3,046#
28’ GLCSL2000-10 (S or AL)-28 Steel 25’ 2 7/8 8 1/16 8’-0” 13 23 27 7/16 8 7/8 3 1/2 15 3/8 13 16 1/16 4 @ 3,342#
33’GLC2000-10 (S or AL)-33
GLCS2000-10 (S or AL)-33AL2000-10-33
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
8’-0”8’-0”8’-0”
1313
17 1/16
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
8 7/88 7/8
13 3/8
3 1/23 1/2
11
-12-
131339
16 1/1616 1/16
16 15/16
14 @ 2,913#6 @ 3,196#6 @ 3,046#
34’ GLCSLX2000-10 (S or AL)-34 Steel 30’ 2 7/8 8 1/16 8’-0” 13 25 5/8 30 1/16 8 7/8 3 1/2 18 13 16 1/16 4 @ 3,462#
43’GLC2000-10 (S or AL)-43
GLCS2000-10 (S or AL)-43AL2000-10-43
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
8’-0”8’-0”8’-0”
1313
17 1/16
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
8 7/88 7/8
13 3/8
3 1/23 1/2
11
-12-
191949
16 1/1616 1/16
16 15/16
18 @ 2,913#6 @ 3,196#6 @ 3,046#
53’
GLC2000-10 (S or AL)-53GLCS2000-10 (S or AL)-53
AL2000-10-53GLCSL2000-10 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
2 7/82 7/82 3/82 7/8
8 1/168 1/16
88 1/16
8’-0”8’-0”8’-0”8’-0”
1313
17 1/1613
11 1/819 5/8
25 5/1623
15 9/1624 1/16
-27 7/16
8 7/88 7/8
13 3/88 7/8
3 1/23 1/2
113 1/2
-12-
15 3/8
19195319
16 1/1616 1/16
16 15/1616 1/16
22 @ 2,913#8 @ 3,196#8 @ 3,046#6 @ 3,342#
63’GLC2000-10 (S or AL)-63
GLCS2000-10 (S or AL)-63AL2000-10-63
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
8’-0”8’-0”8’-0”
1313
17 1/16
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
8 7/88 7/8
13 3/8
3 1/23 1/2
11
-12-
262653
16 1/1616 1/16
16 15/16
26 @ 2,913#8 @ 3,196#8 @ 3,046#
64’ GLCSLX2000-10 (S or AL)-64 Steel 30’ 2 7/8 8 1/16 8’-0” 17 1/16 25 5/8 30 1/16 8 7/8 3 1/2 18 54 16 1/16 6 @ 3,462#78’ GLCSL2000-10 (S or AL)-78 Steel 25’ 2 7/8 8 1/16 8’-0” 17 1/16 23 27 7/16 8 7/8 3 1/2 15 3/8 54 16 1/16 8 @ 3,342#
83’GLC2000-10 (S or AL)-83
GLCS2000-10 (S or AL)-83AL2000-10-83
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
8’-0”8’-0”8’-0”
17 1/1617 1/1617 1/16
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
8 7/88 7/8
13 3/8
3 1/23 1/2
11
-12-
545453
16 1/1616 1/16
16 15/16
34 @ 2,913#10 @ 3,196#10 @ 3,046#
94’ GLCSLX2000-10 (S or AL)-94 Steel 30’ 2 7/8 8 1/16 8’-0” 17 1/16 25 5/8 30 1/16 8 7/8 3 1/2 18 54 16 1/16 8 @ 3,462#
103’
GLC2000-10 (S or AL)-103GLCS2000-10 (S or AL)-103
AL2000-10-103GLCSL2000-10 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
2 7/82 7/82 3/82 7/8
8 1/168 1/16
88 1/16
8’-0”8’-0”8’-0”8’-0”
17 1/1617 1/1617 1/1617 1/16
11 1/819 5/8
25 5/1623
15 9/1624 1/16
-27 7/16
8 7/88 7/8
13 3/88 7/8
3 1/23 1/2
113 1/2
-12-
15 3/8
54545354
16 1/1616 1/16
16 15/1616 1/16
42 @ 2,913#12 @ 3,196#12 @ 3,046#10 @ 3,342#
124’ GLCSLX2000-10 (S or AL)-124 Steel 30’ 2 7/8 8 1/16 8’-0” 17 1/16 25 5/8 30 1/16 8 7/8 3 1/2 18 54 16 1/16 10 @ 3,462#
*This column provides the total number of support hangers with the corresponding ver cal load applied by each support hanger (in pounds) based on the “L1” dimensions shown. Up to a 20” hanger drop will be provided by Gorbel. Addi onal hanger points or longer drops can be provided at an addi onal charge.
Gorbel® Ceiling Mounted Work Sta on Bridge Crane Kits include: bridge, runways, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Sway bracing is required on all systems except fl ush mounted systems (by others). Sway bracing kits are available but not included in the crane kit. Hoist provided by others.
Dimensions are for reference only and are subject to change without no ce.
2000# CAPACITY
49
CEI
LIN
G M
OU
NTE
D W
OR
KST
ATIO
N B
RID
GE
CR
AN
ES
50
2000# CAPACITYCEILING MOUNTED WORK STATION BRIDGE CRANES
BRIDGE LENGTH
(L)
RUNWAY LENGTH MODEL NUMBER TRACK
MATL.
BRIDGE RUNWAYMAX
L1T1in
L3in
L4
L6in
H3in
H3Ain
H4in
H2in
H1in
L7in
L8in
HANGERS(See Note)*
15’
23’GLC2000-15 (S or AL)-23
GLCS2000-15 (S or AL)-23AL2000-15-23
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
13’-0”13’-0”13’-0”
1717
23 3/4
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
14 7/814 7/813 3/8
3 1/23 1/2
11
-12-
99
26
16 1/1616 1/16
16 15/16
10 @ 2,965#4 @ 3,248#4 @ 3,073#
28’ GLCSL2000-15 (S or AL)-28 Steel 25’ 2 7/8 8 1/16 13’-0” 17 23 27 7/16 14 7/8 3 1/2 15 3/8 13 16 1/16 4 @ 3,394#
33’GLC2000-15 (S or AL)-33
GLCS2000-15 (S or AL)-33AL2000-15-33
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
13’-0”13’-0”13’-0”
1717
23 3/4
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
14 7/814 7/813 3/8
3 1/23 1/2
11
-12-
131339
16 1/1616 1/16
16 15/16
14 @ 2,965#6 @ 3,248#6 @ 3,073#
34’ GLCSLX2000-15 (S or AL)-34 Steel 30’ 2 7/8 8 1/16 13’-0” 17 25 5/8 30 1/16 14 7/8 3 1/2 18 13 16 1/16 4 @ 3,514#
43’GLC2000-15 (S or AL)-43
GLCS2000-15 (S or AL)-43AL2000-15-43
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
13’-0”13’-0”13’-0”
1717
23 3/4
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
14 7/814 7/813 3/8
3 1/23 1/2
11
-12-
191949
16 1/1616 1/16
16 15/16
18 @ 2,965#6 @ 3,248#6 @ 3,073#
53’
GLC2000-15 (S or AL)-53GLCS2000-15 (S or AL)-53
AL2000-15-53GLCSL2000-15 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
2 7/82 7/82 3/82 7/8
8 1/168 1/16
88 1/16
13’-0”13’-0”13’-0”13’-0”
1717
23 3/417
11 1/819 5/8
25 5/1623
15 9/1624 1/16
-27 7/16
14 7/814 7/813 3/814 7/8
3 1/23 1/2
113 1/2
-12-
15 3/8
19195319
16 1/1616 1/16
16 15/1616 1/16
22 @ 2,965#8 @ 3,248#8 @ 3,073#6 @ 3,394#
63’GLC2000-15 (S or AL)-63
GLCS2000-15 (S or AL)-63AL2000-15-63
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
13’-0”13’-0”13’-0”
1717
23 3/4
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
14 7/814 7/813 3/8
3 1/23 1/2
11
-12-
262653
16 1/1616 1/16
16 15/16
26 @ 2,965#8 @ 3,248#8 @ 3,073#
64’ GLCSLX2000-15 (S or AL)-64 Steel 30’ 2 7/8 8 1/16 13’-0” 23 3/4 25 5/8 30 1/16 14 7/8 3 1/2 18 54 16 1/16 6 @ 3,514#78’ GLCSL2000-15 (S or AL)-78 Steel 25’ 2 7/8 8 1/16 13’-0” 23 3/4 23 27 7/16 14 7/8 3 1/2 15 3/8 54 16 1/16 8 @ 3,394#
83’GLC2000-15 (S or AL)-83
GLCS2000-15 (S or AL)-83AL2000-15-83
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
13’-0”13’-0”13’-0”
23 3/423 3/423 3/4
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
14 7/814 7/813 3/8
3 1/23 1/2
11
-12-
545453
16 1/1616 1/16
16 15/16
34 @ 2,965#10 @ 3,248#10 @ 3,073#
94’ GLCSLX-15 (S or AL)-94 Steel 30’ 2 7/8 8 1/16 13’-0” 23 3/4 25 5/8 30 1/16 14 7/8 3 1/2 18 54 16 1/16 8 @ 3,514#
103’
GLC2000-15 (S or AL)-103GLCS2000-15 (S or AL)-103
AL2000-15-103GLCSL2000-15 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
2 7/82 7/82 3/82 7/8
8 1/168 1/16
88 1/16
13’-0”13’-0”13’-0”13’-0”
23 3/423 3/423 3/423 3/4
11 1/819 5/8
25 5/1623
15 9/1624 1/16
-27 7/16
14 7/814 7/813 3/814 7/8
3 1/23 1/2
113 1/2
-12-
15 3/8
54545354
16 1/1616 1/16
16 15/1616 1/16
42 @ 2,965#12 @ 3,248#12 @ 3,073#10 @ 3,394#
124’ GLCSLX2000-15 (S or AL)-124 Steel 30’ 2 7/8 8 1/16 13’-0” 23 3/4 25 5/8 30 1/16 14 7/8 3 1/2 18 54 16 1/16 10 @ 3,514#
20’
23’GLC2000-20 (S or AL)-23
GLCS2000-20 (S or AL)-23AL2000-20-23
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
18’-0”18’-0”18’-0”
1919
27 1/8
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
14 7/814 7/815 1/2
3 1/23 1/2
13 1/8
-12-
99
26
16 1/1616 1/16
16 15/16
10 @ 3,007#4 @ 3,290#4 @ 3,105#
28’ GLCSL2000-20 (S or AL)-28 Steel 25’ 2 7/8 8 1/16 18’-0” 19 23 27 7/16 14 7/8 3 1/2 15 3/8 13 16 1/16 4 @ 3,437#
33’GLC2000-20 (S or AL)-33
GLCS2000-20 (S or AL)-33AL2000-20-33
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
18’-0”18’-0”18’-0”
1919
27 1/8
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
14 7/814 7/815 1/2
3 1/23 1/2
13 1/8
-12-
131339
16 1/1616 1/16
16 15/16
14 @ 3,007#6 @ 3,290#6 @ 3,105#
34’ GLCSLX2000-20 (S or AL)-34 Steel 30’ 2 7/8 8 1/16 18’-0” 19 25 5/8 30 1/16 14 7/8 3 1/2 18 13 16 1/16 4 @ 3,556#
43’GLC2000-20 (S or AL)-43
GLCS2000-20 (S or AL)-43AL2000-20-43
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
18’-0”18’-0”18’-0”
1919
27 1/8
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
14 7/814 7/815 1/2
3 1/23 1/2
13 1/8
-12-
191949
16 1/1616 1/16
16 15/16
18 @ 3,007#6 @ 3,290#6 @ 3,105#
53’
GLC2000-20 (S or AL)-53GLCS2000-20 (S or AL)-53
AL2000-20-53GLCSL2000-20 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
2 7/82 7/82 3/82 7/8
8 1/168 1/16
88 1/16
18’-0”18’-0”18’-0”18’-0”
1919
27 1/819
11 1/819 5/8
25 5/1623
15 9/1624 1/16
-27 7/16
14 7/814 7/815 1/214 7/8
3 1/23 1/2
13 1/83 1/2
-12-
15 3/8
19195319
16 1/1616 1/16
16 15/1616 1/16
22 @ 3,007#8 @ 3,290#8 @ 3,105#6 @ 3,437#
63’GLC2000-20 (S or AL)-63
GLCS2000-20 (S or AL)-63AL2000-20-63
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
18’-0”18’-0”18’-0”
1919
27 1/8
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
14 7/814 7/815 1/2
3 1/23 1/2
13 1/8
-12-
262653
16 1/1616 1/16
16 15/16
26 @ 3,007#8 @ 3,290#8 @ 3,105#
64’ GLCSLX2000-20 (S or AL)-64 Steel 30’ 2 7/8 8 1/16 18’-0” 27 1/8 25 5/8 30 1/16 14 7/8 3 1/2 18 54 16 1/16 6 @ 3,556#78’ GLCSL2000-20 (S or AL)-78 Steel 25’ 2 7/8 8 1/16 18’-0” 27 1/8 23 27 7/16 14 7/8 3 1/2 15 3/8 54 16 1/16 8 @ 3,437#
83’GLC2000-20 (S or AL)-83
GLCS2000-20 (S or AL)-83AL2000-20-83
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
18’-0”18’-0”18’-0”
27 1/827 1/827 1/8
11 1/819 5/8
25 5/16
15 9/1624 1/16
-
14 7/814 7/815 1/2
3 1/23 1/2
13 1/8
-12-
545453
16 1/1616 1/16
16 15/16
34 @ 3,007#10 @ 3,290#10 @ 3,105#
94’ GLCSLX2000-20 (S or AL)-94 Steel 30’ 2 7/8 8 1/16 18’-0” 27 1/8 25 5/8 30 1/16 14 7/8 3 1/2 18 54 16 1/16 8 @ 3,556#
103’
GLC2000-20 (S or AL)-103GLCS2000-20 (S or AL)-103
AL2000-20-103GLCSL2000-20 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
2 7/82 7/82 3/82 7/8
8 1/168 1/16
88 1/16
18’-0”18’-0”18’-0”18’-0”
27 1/827 1/827 1/827 1/8
11 1/819 5/8
25 5/1623
15 9/1624 1/16
-27 7/16
14 7/814 7/815 1/214 7/8
3 1/23 1/2
13 1/83 1/2
-12-
15 3/8
54545354
16 1/1616 1/16
16 15/1616 1/16
42 @ 3,007#12 @ 3,290#12 @ 3,105#10 @ 3,437#
124’ GLCSLX2000-20 (S or AL)-124 Steel 30’ 2 7/8 8 1/16 18’-0” 27 1/8 25 5/8 30 1/16 14 7/8 3 1/2 18 54 16 1/16 10 @ 3,556#
*This column provides the total number of support hangers with the corresponding ver cal load applied by each support hanger (in pounds) based on the “L1” dimensions shown. Up to a 20” hanger drop will be provided by Gorbel. Addi onal hanger points or longer drops can be provided at an addi onal charge.
Gorbel® Ceiling Mounted Work Sta on Bridge Crane Kits include: bridge, runways, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Sway bracing is required on all systems except fl ush mounted systems (by others). Sway bracing kits are available but not included in the crane kit. Hoist provided by others.
Dimensions are for reference only and are subject to change without no ce.
CEILIN
G M
OU
NTED
WO
RK
STATION
BR
IDG
E CR
AN
ES
51
2000# CAPACITYCEILING MOUNTED WORK STATION BRIDGE CRANES
BRIDGE LENGTH
(L)
RUNWAY LENGTH MODEL NUMBER TRACK
MATL.
BRIDGE RUNWAYMAX
L1T1in
L3in
L4
L6in
H3in
H3Ain
H4in
H2in
H1in
L7in
L8in
HANGERS(See Note)*
23’
23’GLC2000-23 (S or AL)-23
GLCS2000-23 (S or AL)-23AL2000-23-23
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
21’-0”21’-0”20’-0”
2121
30 7/16
11 1/819 5/8
25 5/16
17 9/1626 1/6
-
14 7/814 7/815 1/2
3 1/23 1/2
13 1/8
-12-
99
26
16 1/1616 1/16
16 15/16
10 @ 3,033#4 @ 3,316#4 @ 3,116#
28’ GLCSL2000-23 (S or AL)-28 Steel 25’ 2 7/8 8 1/16 21’-0” 21 23 29 7/16 14 7/8 3 1/2 15 3/8 13 16 1/16 4 @ 3,462#
33’GLC2000-23 (S or AL)-33
GLCS2000-23 (S or AL)-33AL2000-23-33
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
21’-0”21’-0”20’-0”
2121
30 7/16
11 1/819 5/8
25 5/16
17 9/1626 1/6
-
14 7/814 7/815 1/2
3 1/23 1/2
13 1/8
-12-
131339
16 1/1616 1/16
16 15/16
14 @ 3,033#6 @ 3,316#6 @ 3,116#
34’ GLCSLX2000-23 (S or AL)-34 Steel 30’ 2 7/8 8 1/16 21’-0” 21 25 5/8 32 1/16 14 7/8 3 1/2 18 13 16 1/16 4 @ 3,582#
43’GLC2000-23 (S or AL)-43
GLCS2000-23 (S or AL)-43AL2000-23-43
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
21’-0”21’-0”20’-0”
2121
30 7/16
11 1/819 5/8
25 5/16
17 9/1626 1/6
-
14 7/814 7/815 1/2
3 1/23 1/2
13 1/8
-12-
191949
16 1/1616 1/16
16 15/16
18 @ 3,033#6 @ 3,316#6 @ 3,116#
53’
GLC2000-23 (S or AL)-53GLCS2000-23 (S or AL)-53
AL2000-23-53GLCSL2000-23 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
2 7/82 7/82 3/82 7/8
8 1/168 1/16
88 1/16
21’-0”21’-0”20’-0”21’-0”
2121
30 7/1621
11 1/819 5/8
25 5/1623
17 9/1626 1/6
-29 7/16
14 7/814 7/815 1/214 7/8
3 1/23 1/2
13 1/83 1/2
-12-
15 3/8
19195319
16 1/1616 1/16
16 15/1616 1/16
22 @ 3,033#8 @ 3,316#8 @ 3,116#6 @ 3,462#
63’GLC2000-23 (S or AL)-63
GLCS2000-23 (S or AL)-63AL2000-23-63
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
21’-0”21’-0”20’-0”
2121
30 7/16
11 1/819 5/8
25 5/16
17 9/1626 1/6
-
14 7/814 7/815 1/2
3 1/23 1/2
13 1/8
-12-
262653
16 1/1616 1/16
16 15/16
26 @ 3,033#8 @ 3,316#8 @ 3,116#
64’ GLCSLX2000-23 (S or AL)-64 Steel 30’ 2 7/8 8 1/16 21’-0” 30 7/16 25 5/8 32 1/16 14 7/8 3 1/2 18 54 16 1/16 6 @ 3,582#78’ GLCSL2000-23 (S or AL)-78 Steel 25’ 2 7/8 8 1/16 21’-0” 30 7/16 23 29 7/16 14 7/8 3 1/2 15 3/8 54 16 1/16 8 @ 3,462#
83’GLC2000-23 (S or AL)-83
GLCS2000-23 (S or AL)-83AL2000-23-83
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
21’-0”21’-0”20’-0”
30 7/1630 7/1630 7/16
11 1/819 5/8
25 5/16
17 9/1626 1/6
-
14 7/814 7/815 1/2
3 1/23 1/2
13 1/8
-12-
545453
16 1/1616 1/16
16 15/16
34 @ 3,033#10 @ 3,316#10 @ 3,116#
94’ GLCSLX-23 (S or AL)-94 Steel 30’ 2 7/8 8 1/16 21’-0” 30 7/16 25 5/8 32 1/16 14 7/8 3 1/2 18 54 16 1/16 8 @ 3,582#
103’
GLC2000-23 (S or AL)-103GLCS2000-23 (S or AL)-103
AL2000-23-103GLCSL2000-23 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
2 7/82 7/82 3/82 7/8
8 1/168 1/16
88 1/16
21’-0”21’-0”20’-0”21’-0”
30 7/1630 7/1630 7/1630 7/16
11 1/819 5/8
25 5/1623
17 9/1626 1/6
-29 7/16
14 7/814 7/815 1/214 7/8
3 1/23 1/2
13 1/83 1/2
-12-
15 3/8
54545354
16 1/1616 1/16
16 15/1616 1/16
42 @ 3,033#12 @ 3,316#12 @ 3,116#10 @ 3,462#
124’ GLCSLX2000-23 (S or AL)-124 Steel 30’ 2 7/8 8 1/16 21’-0” 30 7/16 25 5/8 32 1/16 14 7/8 3 1/2 18 54 16 1/16 10 @ 3,582#
28’
23’GLC2000-28 (S or AL)-23
GLCS2000-28 (S or AL)-23AL2000-28-23
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
25’-0”25’-0”25’-0”
2525
37 3/16
14 7/1622 15/16
27 1/2
17 9/1626 1/6
-
18 1/418 1/4
17
3 1/23 1/2
14 5/8
-12-
99
26
25 7/825 7/8
21
10 @ 3,097#4 @ 3,380#4 @ 3,162#
28’ GLCSL2000-28 (S or AL)-28 Steel 25’ 2 7/8 8 1/16 25’-0” 25 26 5/16 29 7/16 18 1/4 3 1/2 15 3/8 13 25 7/8 4 @ 3,527#
33’GLC2000-28 (S or AL)-33
GLCS2000-28 (S or AL)-33AL2000-28-33
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
25’-0”25’-0”25’-0”
2525
37 3/16
14 7/1622 15/16
27 1/2
17 9/1626 1/6
-
18 1/418 1/4
17
3 1/23 1/2
14 5/8
-12-
131330
25 7/825 7/8
21
14 @ 3,097#6 @ 3,380#6 @ 3,162#
34’ GLCSLX2000-28 (S or AL)-34 Steel 30’ 2 7/8 8 1/16 25’-0” 25 28 15/16 32 1/16 18 1/4 3 1/2 18 13 25 7/8 4 @ 3,646#
43’GLC2000-28 (S or AL)-43
GLCS2000-28 (S or AL)-43AL2000-28-43
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
25’-0”25’-0”25’-0”
2525
37 3/16
14 7/1622 15/16
27 1/2
17 9/1626 1/6
-
18 1/418 1/4
17
3 1/23 1/2
14 5/8
-12-
191949
25 7/825 7/8
21
18 @ 3,097#6 @ 3,380#6 @ 3,162#
53’
GLC2000-28 (S or AL)-53GLCS2000-28 (S or AL)-53
AL2000-28-53GLCSL2000-28 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
2 7/82 7/82 3/82 7/8
8 1/168 1/16
88 1/16
25’-0”25’-0”25’-0”25’-0”
2525
37 3/1625
14 7/1622 15/16
27 1/226 5/16
17 9/1626 1/6
-29 7/16
18 1/418 1/4
1718 1/4
3 1/23 1/2
14 5/83 1/2
-12-
15 3/8
19195319
25 7/825 7/8
2125 7/8
22 @ 3,097#8 @ 3,380#8 @ 3,162#6 @ 3,527#
63’GLC2000-28 (S or AL)-63
GLCS2000-28 (S or AL)-63AL2000-28-63
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
25’-0”25’-0”25’-0”
2525
37 3/16
14 7/1622 15/16
27 1/2
17 9/1626 1/6
-
18 1/418 1/4
17
3 1/23 1/2
14 5/8
-12-
262653
25 7/825 7/8
21
26 @ 3,097#8 @ 3,380#8 @ 3,162#
64’ GLCSLX2000-28 (S or AL)-64 Steel 30’ 2 7/8 8 1/16 25’-0” 37 3/16 28 15/16 32 1/16 18 1/4 3 1/2 18 54 25 7/8 6 @ 3,646#78’ GLCSL2000-28 (S or AL)-78 Steel 25’ 2 7/8 8 1/16 25’-0” 37 3/16 26 5/16 29 7/16 18 1/4 3 1/2 15 3/8 54 25 7/8 8 @ 3,527#
83’GLC2000-28 (S or AL)-83
GLCS2000-28 (S or AL)-83AL2000-28-83
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
25’-0”25’-0”25’-0”
37 3/1637 3/1637 3/16
14 7/1622 15/16
27 1/2
17 9/1626 1/6
-
18 1/418 1/4
17
3 1/23 1/2
14 5/8
-12-
545453
25 7/825 7/8
21
34 @ 3,097#10 @ 3,380#10 @ 3,162#
94’ GLCSLX2000-28 (S or AL)-94 Steel 30’ 2 7/8 8 1/16 25’-0” 37 3/16 28 15/16 32 1/16 18 1/4 3 1/2 18 54 25 7/8 8 @ 3,646#
103’
GLC2000-28 (S or AL)-103GLCS2000-28 (S or AL)-103
AL2000-28-103GLCSL2000-28 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
2 7/82 7/82 3/82 7/8
8 1/168 1/16
88 1/16
25’-0”25’-0”25’-0”25’-0”
37 3/1637 3/1637 3/1637 3/16
14 7/1622 15/16
27 1/226 5/16
17 9/1626 1/6
-29 7/16
18 1/418 1/4
1718 1/4
3 1/23 1/2
14 5/83 1/2
-12-
15 3/8
54545354
25 7/825 7/8
2125 7/8
42 @ 3,097#12 @ 3,380#12 @ 3,162#10 @ 3,527#
124’ GLCSLX2000-28 (S or AL)-124 Steel 30’ 2 7/8 8 1/16 25’-0” 37 3/16 28 15/16 32 1/16 18 1/4 3 1/2 18 54 25 7/8 10 @ 3,646#
*This column provides the total number of support hangers with the corresponding ver cal load applied by each support hanger (in pounds) based on the “L1” dimensions shown. Up to a 20” hanger drop will be provided by Gorbel. Addi onal hanger points or longer drops can be provided at an addi onal charge.
Gorbel® Ceiling Mounted Work Sta on Bridge Crane Kits include: bridge, runways, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Sway bracing is required on all systems except fl ush mounted systems (by others). Sway bracing kits are available but not included in the crane kit. Hoist provided by others.
Dimensions are for reference only and are subject to change without no ce.
CEI
LIN
G M
OU
NTE
D W
OR
KST
ATIO
N B
RID
GE
CR
AN
ES
52
2000# CAPACITYCEILING MOUNTED WORK STATION BRIDGE CRANES
BRIDGE LENGTH
(L)
RUNWAY LENGTH MODEL NUMBER TRACK
MATL.
BRIDGE RUNWAYMAX
L1T1in
L3in
L4
L6in
H3in
H3Ain
H4in
H2in
H1in
L7in
L8in
HANGERS(See Note)*
34’
28’ GLCSL2000-15 (S or AL)-28 Steel 25’ 2 7/8 8 1/16 30’-0” 29 26 5/16 29 7/16 20 7/8 3 1/2 15 3/8 13 25 7/8 4 @ 3,587#
33’GLC2000-15 (S or AL)-33
GLCS2000-15 (S or AL)-33AL2000-15-33
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
30’-0”30’-0”30’-0”
2929
43 7/8
14 7/1622 15/16
27 1/2
17 9/1626 1/16
-
20 7/820 7/817 7/8
3 1/23 1/2
15 1/2
-12-
131339
25 7/825 7/8
21
14 @ 3,157#6 @ 3,440#6 @ 3,245#
34’ GLCSLX2000-15 (S or AL)-34 Steel 30’ 2 7/8 8 1/16 30’-0” 29 28 15/16 32 1/16 20 7/8 3 1/2 18 13 25 7/8 4 @ 3,706#
43’GLC2000-15 (S or AL)-43
GLCS2000-15 (S or AL)-43AL2000-15-43
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
30’-0”30’-0”30’-0”
2929
43 7/8
14 7/1622 15/16
27 1/2
17 9/1626 1/16
-
20 7/820 7/817 7/8
3 1/23 1/2
15 1/2
-12-
191949
25 7/825 7/8
21
18 @ 3,157#6 @ 3,440#6 @ 3,245#
53’
GLC2000-15 (S or AL)-53GLCS2000-15 (S or AL)-53
AL2000-15-53GLCSL2000-15 (S or AL)-53
SteelSteelAlumSteel
6’20’20’25’
2 7/82 7/82 3/82 7/8
8 1/168 1/16
88 1/16
30’-0”30’-0”30’-0”30’-0”
2929
43 7/829
14 7/1622 15/16
27 1/226 5/16
17 9/1626 1/16
-29 7/16
20 7/820 7/817 7/820 7/8
3 1/23 1/2
15 1/23 1/2
-12-
15 3/8
19195319
25 7/825 7/8
2125 7/8
22 @ 3,157#8 @ 3,440#8 @ 3,245#6 @ 3 ,587#
63’GLC2000-15 (S or AL)-63
GLCS2000-15 (S or AL)-63AL2000-15-63
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
30’-0”30’-0”30’-0”
2929
43 7/8
14 7/1622 15/16
27 1/2
17 9/1626 1/16
-
20 7/820 7/817 7/8
3 1/23 1/2
15 1/2
-12-
262653
25 7/825 7/8
21
26 @ 3,157#8 @ 3,440#8 @ 3,245#
64’ GLCSLX2000-15 (S or AL)-64 Steel 30’ 2 7/8 8 1/16 30’-0” 43 7/8 28 15/16 32 1/16 20 7/8 3 1/2 18 54 25 7/8 6 @ 3,706#78’ GLCSL2000-15 (S or AL)-78 Steel 25’ 2 7/8 8 1/16 30’-0” 43 7/8 26 5/16 29 7/16 20 7/8 3 1/2 15 3/8 54 25 7/8 8 @ 3,587#
83’GLC2000-15 (S or AL)-83
GLCS2000-15 (S or AL)-83AL2000-15-83
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
8 1/168 1/16
8
30’-0”30’-0”30’-0”
43 7/843 7/843 7/8
14 7/1622 15/16
27 1/2
17 9/1626 1/16
-
20 7/820 7/817 7/8
3 1/23 1/2
15 1/2
-12-
545453
25 7/825 7/8
21
34 @ 3,157#10 @ 3,440#10 @ 3,245#
94’ GLCSLX-15 (S or AL)-94 Steel 30’ 2 7/8 8 1/16 30’-0” 43 7/8 28 15/16 32 1/16 20 7/8 3 1/2 18 54 25 7/8 8 @ 3,706#
103’
GLC2000-15 (S or AL)-103GLCS2000-15 (S or AL)-103
AL2000-15-103GLCSL2000-15 (S or AL)-103
SteelSteelAlumSteel
6’20’20’25’
2 7/82 7/82 3/82 7/8
8 1/168 1/16
88 1/16
30’-0”30’-0”30’-0”30’-0”
43 7/843 7/843 7/843 7/8
14 7/1622 15/16
27 1/226 5/16
17 9/1626 1/16
-29 7/16
20 7/820 7/817 7/820 7/8
3 1/23 1/2
15 1/23 1/2
-12-
15 3/8
54545354
25 7/825 7/8
2125 7/8
42 @ 3,157#12 @ 3,440#12 @ 3,245#10 @ 3,587#
124’ GLCSLX2000-15 (S or AL)-124 Steel 30’ 2 7/8 8 1/16 30’-0” 43 7/8 28 15/16 32 1/16 20 7/8 3 1/2 18 54 25 7/8 10 @ 3,706#
*This column provides the total number of support hangers with the corresponding ver cal load applied by each support hanger (in pounds) based on the “L1” dimensions shown. Up to a 20” hanger drop will be provided by Gorbel. Addi onal hanger points or longer drops can be provided at an addi onal charge.
Gorbel® Ceiling Mounted Work Sta on Bridge Crane Kits include: bridge, runways, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Sway bracing is required on all systems except fl ush mounted systems (by others). Sway bracing kits are available but not included in the crane kit. Hoist provided by others.
Dimensions are for reference only and are subject to change without no ce.
CEILIN
G M
OU
NTED
WO
RK
STATION
BR
IDG
E CR
AN
ES
4000# CAPACITY
53
CEI
LIN
G M
OU
NTE
D W
OR
KST
ATIO
N B
RID
GE
CR
AN
ES
CEILING MOUNTED WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH MODEL NUMBER TRACK
MATL.
BRIDGE RUNWAYMAX
L1T1in
L3in
L4
L6in
H3in
H3Ain
H4in
H2in
H1in
L7in
L8in
HANGERS(See Note)*
15’
23’ GLC4000-15 (S or AL)-23GLCS4000-15 (S or AL)-23
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
12’-6”12’-6”
2424
11 7/1629 7/16
14 1/232 1/2
21 3/821 3/8
3 1/23 1/2
-18
99
25 7/825 7/8
14 @ 5,730#4 @ 6,143#
28’ GLCSL4000-15 (S or AL)-28 Steel 25’ 3 3/8 15 1/16 12’-6” 24 31 7/16 34 1/2 21 3/8 3 1/2 20 13 25 7/8 4 @ 6,385#
33’ GLC4000-15 (S or AL)-33GLCS4000-15 (S or AL)-33
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
12’-6”12’-6”
2424
11 7/1629 7/16
14 1/232 1/2
21 3/821 3/8
3 1/23 1/2
-18
1313
25 7/825 7/8
20 @ 5,730#6 @ 6,143#
34’ GLCSLX4000-15 (S or AL)-34 Steel 30’ 3 3/8 15 1/16 12’-6” 24 32 7/16 35 1/2 21 3/8 3 1/2 22 13 25 7/8 4 @ 6,652#
43’ GLC4000-15 (S or AL)-43GLCS4000-15 (S or AL)-43
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
12’-6”12’-6”
2424
11 7/1629 7/16
14 1/232 1/2
21 3/821 3/8
3 1/23 1/2
-18
1919
25 7/825 7/8
24 @ 5,730#6 @ 6,143#
53’GLC4000-15 (S or AL)-53
GLCS4000-15 (S or AL)-53GLCSL4000-15 (S or AL)-53
SteelSteelSteel
4’20’25’
3 3/83 3/83 3/8
15 1/1615 1/1615 1/16
12’-6”12’-6”12’-6”
242424
11 7/1629 7/1631 7/16
14 1/232 1/234 1/2
21 3/821 3/821 3/8
3 1/23 1/23 1/2
-1820
191919
25 7/825 7/825 7/8
30 @ 5,730#8 @ 6,143#6 @ 6,385#
63’ GLC4000-15 (S or AL)-63GLCS4000-15 (S or AL)-63
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
12’-6”12’-6”
2424
11 7/1629 7/16
14 1/232 1/2
21 3/821 3/8
3 1/23 1/2
-18
2626
25 7/825 7/8
34 @ 5,730#8 @ 6,143#
64’ GLCSLX4000-15 (S or AL)-64 Steel 30’ 3 3/8 15 1/16 12’-6” 30 3/4 32 7/16 35 1/2 21 3/8 3 1/2 22 54 25 7/8 6 @ 6,652#78’ GLCSL4000-15 (S or AL)-78 Steel 25’ 3 3/8 15 1/16 12’-6” 30 3/4 31 7/16 34 1/2 21 3/8 3 1/2 20 54 25 7/8 8 @ 6,385#
83’ GLC4000-15 (S or AL)-83GLCS4000-15 (S or AL)-83
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
12’-6”12’-6”
30 3/430 3/4
11 7/1629 7/16
14 1/232 1/2
21 3/821 3/8
3 1/23 1/2
-18
5454
25 7/825 7/8
44 @ 5,730#10 @ 6,143#
94’ GLCSLX-15 (S or AL)-94 Steel 30’ 3 3/8 15 1/16 12’-6” 30 3/4 32 7/16 35 1/2 21 3/8 3 1/2 22 54 25 7/8 8 @ 6,652#
103’GLC4000-15 (S or AL)-103
GLCS4000-15 (S or AL)-103GLCSL4000-15 (S or AL)-103
SteelSteelSteel
4’20’25’
3 3/83 3/83 3/8
15 1/1615 1/1615 1/16
12’-6”12’-6”12’-6”
30 3/430 3/430 3/4
11 7/1629 7/1631 7/16
14 1/232 1/234 1/2
21 3/821 3/821 3/8
3 1/23 1/23 1/2
-1820
545454
25 7/825 7/825 7/8
54 @ 5,730#12 @ 6,143#10 @ 6,385#
124’ GLCSLX4000-15 (S or AL)-124 Steel 30’ 3 3/8 15 1/16 12’-6” 30 3/4 32 7/16 35 1/2 21 3/8 3 1/2 22 54 25 7/8 10 @ 6,652#
20’
23’ GLC4000-20 (S or AL)-23GLCS4000-20 (S or AL)-23
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
17’-6”17’-6”
2626
11 7/1629 7/16
14 1/232 1/2
21 3/821 3/8
3 1/23 1/2
-18
99
25 7/825 7/8
14 @ 5,781#4 @ 6,195#
28’ GLCSL4000-20 (S or AL)-28 Steel 25’ 3 3/8 15 1/16 17’-6” 26 31 7/16 34 1/2 21 3/8 3 1/2 20 13 25 7/8 4 @ 6,437#
33’ GLC4000-20 (S or AL)-33GLCS4000-20 (S or AL)-33
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
17’-6”17’-6”
2626
11 7/1629 7/16
14 1/232 1/2
21 3/821 3/8
3 1/23 1/2
-18
1313
25 7/825 7/8
20 @ 5,781#6 @ 6,195#
34’ GLCSLX4000-20 (S or AL)-34 Steel 30’ 3 3/8 15 1/16 17’-6” 26 32 7/16 35 1/2 21 3/8 3 1/2 22 13 25 7/8 4 @ 6,704#
43’ GLC4000-20 (S or AL)-43GLCS4000-20 (S or AL)-43
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
17’-6”17’-6”
2626
11 7/1629 7/16
14 1/232 1/2
21 3/821 3/8
3 1/23 1/2
-18
1919
25 7/825 7/8
24 @ 5,781#6 @ 6,195#
53’GLC4000-20 (S or AL)-53
GLCS4000-20 (S or AL)-53GLCSL4000-20 (S or AL)-53
SteelSteelSteel
4’20’25’
3 3/83 3/83 3/8
15 1/1615 1/1615 1/16
17’-6”17’-6”17’-6”
262626
11 7/1629 7/1631 7/16
14 1/232 1/234 1/2
21 3/821 3/821 3/8
3 1/23 1/23 1/2
-1820
191919
25 7/825 7/825 7/8
30 @ 5,781#8 @ 6,195#6 @ 6,437#
63’ GLC4000-20 (S or AL)-63GLCS4000-20 (S or AL)-63
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
17’-6”17’-6”
2626
11 7/1629 7/16
14 1/232 1/2
21 3/821 3/8
3 1/23 1/2
-18
2626
25 7/825 7/8
34 @ 5,781#8 @ 6,195#
64’ GLCSLX4000-20 (S or AL)-64 Steel 30’ 3 3/8 15 1/16 17’-6” 34 1/8 32 7/16 35 1/2 21 3/8 3 1/2 22 54 25 7/8 6 @ 6,704#78’ GLCSL4000-20 (S or AL)-78 Steel 25’ 3 3/8 15 1/16 17’-6” 34 1/8 31 7/16 34 1/2 21 3/8 3 1/2 20 54 25 7/8 8 @ 6,437#
83’ GLC4000-20 (S or AL)-83GLCS4000-20 (S or AL)-83
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
17’-6”17’-6”
34 1/834 1/8
11 7/1629 7/16
14 1/232 1/2
21 3/821 3/8
3 1/23 1/2
-18
5454
25 7/825 7/8
44 @ 5,781#10 @ 6,195#
94’ GLCSLX4000-20 (S or AL)-94 Steel 30’ 3 3/8 15 1/16 17’-6” 34 1/8 32 7/16 35 1/2 21 3/8 3 1/2 22 54 25 7/8 8 @ 6,704#
103’GLC4000-20 (S or AL)-103
GLCS4000-20 (S or AL)-103GLCSL4000-20 (S or AL)-103
SteelSteelSteel
4’20’25’
3 3/83 3/83 3/8
15 1/1615 1/1615 1/16
17’-6”17’-6”17’-6”
34 1/834 1/834 1/8
11 7/1629 7/1631 7/16
14 1/232 1/234 1/2
21 3/821 3/821 3/8
3 1/23 1/23 1/2
-1820
545454
25 7/825 7/825 7/8
54 @ 5,781#12 @ 6,195#10 @ 6,437#
124’ GLCSLX4000-20 (S or AL)-124 Steel 30’ 3 3/8 15 1/16 17’-6” 34 1/8 32 7/16 35 1/2 21 3/8 3 1/2 22 54 25 7/8 10 @ 6,704#
23’
23’ GLC4000-23 (S or AL)-23GLCS4000-23 (S or AL)-23
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
20’-6”20’-6”
2828
11 7/1629 7/16
14 1/232 1/2
21 3/821 3/8
3 1/23 1/2
-18
99
25 7/825 7/8
14 @ 5,812#4 @ 6,226#
28’ GLCSL4000-23 (S or AL)-28 Steel 25’ 3 3/8 15 1/16 20’-6” 28 31 7/16 34 1/2 21 3/8 3 1/2 20 13 25 7/8 4 @ 6,468#
33’ GLC4000-23 (S or AL)-33GLCS4000-23 (S or AL)-33
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
20’-6”20’-6”
2828
11 7/1629 7/16
14 1/232 1/2
21 3/821 3/8
3 1/23 1/2
-18
1313
25 7/825 7/8
20 @ 5,812#6 @ 6,226#
34’ GLCSLX4000-23 (S or AL)-34 Steel 30’ 3 3/8 15 1/16 20’-6” 28 32 7/16 35 1/2 21 3/8 3 1/2 22 13 25 7/8 4 @ 6,735#
43’ GLC4000-23 (S or AL)-43GLCS4000-23 (S or AL)-43
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
20’-6”20’-6”
2828
11 7/1629 7/16
14 1/232 1/2
21 3/821 3/8
3 1/23 1/2
-18
1919
25 7/825 7/8
24 @ 5,812#6 @ 6,226#
53’GLC4000-23 (S or AL)-53
GLCS4000-23 (S or AL)-53GLCSL4000-23 (S or AL)-53
SteelSteelSteel
4’20’25’
3 3/83 3/83 3/8
15 1/1615 1/1615 1/16
20’-6”20’-6”20’-6”
282828
11 7/1629 7/1631 7/16
14 1/232 1/234 1/2
21 3/821 3/821 3/8
3 1/23 1/23 1/2
-1820
191919
25 7/825 7/825 7/8
30 @ 5,812#8 @ 6,226#6 @ 6,468#
*This column provides the total number of support hangers with the corresponding ver cal load applied by each support hanger (in pounds) based on the “L1” dimensions shown. Up to a 20” hanger drop will be provided by Gorbel. Addi onal hanger points or longer drops can be provided at an addi onal charge.
Gorbel® Ceiling Mounted Work Sta on Bridge Crane Kits include: bridge, runways, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Sway bracing is required on all systems except fl ush mounted systems (by others). Sway bracing kits are available but not included in the crane kit. Hoist provided by others.
Dimensions are for reference only and are subject to change without no ce.
54
4000# CAPACITYC
EILING
MO
UN
TED W
OR
KSTATIO
N B
RID
GE C
RA
NES
CEILING MOUNTED WORK STATION BRIDGE CRANESBRIDGE LENGTH
(L)
RUNWAY LENGTH MODEL NUMBER TRACK
MATL.
BRIDGE RUNWAYMAX
L1T1in
L3in
L4
L6in
H3in
H3Ain
H4in
H2in
H1in
L7in
L8in
HANGERS(See Note)*
23’
63’ GLC4000-23 (S or AL)-63GLCS4000-23 (S or AL)-63
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
20’-6”20’-6”
2828
11 7/1629 7/16
14 1/232 1/2
21 3/821 3/8
3 1/23 1/2
-18
2626
25 7/825 7/8
34 @ 5,812#8 @ 6,226#
64’ GLCSLX4000-23 (S or AL)-64 Steel 30’ 3 3/8 15 1/16 20’-6” 37 7/16 32 7/16 35 1/2 21 3/8 3 1/2 22 54 25 7/8 6 @ 6,735#78’ GLCSL4000-23 (S or AL)-78 Steel 25’ 3 3/8 15 1/16 20’-6” 37 7/16 31 7/16 34 1/2 21 3/8 3 1/2 20 54 25 7/8 8 @ 6,468#
83’ GLC4000-23 (S or AL)-83GLCS4000-23 (S or AL)-83
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
20’-6”20’-6”
37 7/1637 7/16
11 7/1629 7/16
14 1/232 1/2
21 3/821 3/8
3 1/23 1/2
-18
5454
25 7/825 7/8
44 @ 5,812#10 @ 6,226#
94’ GLCSLX-23 (S or AL)-94 Steel 30’ 3 3/8 15 1/16 20’-6” 37 7/16 32 7/16 35 1/2 21 3/8 3 1/2 22 54 25 7/8 8 @ 6,735#
103’GLC4000-23 (S or AL)-103
GLCS4000-23 (S or AL)-103GLCSL4000-23 (S or AL)-103
SteelSteelSteel
4’20’25’
3 3/83 3/83 3/8
15 1/1615 1/1615 1/16
20’-6”20’-6”20’-6”
37 7/1637 7/1637 7/16
11 7/1629 7/1631 7/16
14 1/232 1/234 1/2
21 3/821 3/821 3/8
3 1/23 1/23 1/2
-1820
545454
25 7/825 7/825 7/8
54 @ 5,812#12 @ 6,226#10 @ 6,468#
124’ GLCSLX4000-23 (S or AL)-124 Steel 30’ 3 3/8 15 1/16 20’-6” 37 7/16 32 7/16 35 1/2 21 3/8 3 1/2 22 54 25 7/8 10 @ 6,735#
28’
23’ GLC4000-28 (S or AL)-23GLCS4000-28 (S or AL)-23
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
25’-0”25’-0”
3232
11 7/1629 7/16
14 1/232 1/2
23 3/823 3/8
3 1/23 1/2
-18
99
25 7/825 7/8
14 @ 5,928#4 @ 6,342#
28’ GLCSL4000-28 (S or AL)-28 Steel 25’ 3 3/8 15 1/16 25’-0” 32 31 7/16 34 1/2 23 3/8 3 1/2 20 13 25 7/8 4 @ 6,583#
33’ GLC4000-28 (S or AL)-33GLCS4000-28 (S or AL)-33
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
25’-0”25’-0”
3232
11 7/1629 7/16
14 1/232 1/2
23 3/823 3/8
3 1/23 1/2
-18
1313
25 7/825 7/8
20 @ 5,928#6 @ 6,342#
34’ GLCSLX4000-28 (S or AL)-34 Steel 30’ 3 3/8 15 1/16 25’-0” 32 32 7/16 35 1/2 23 3/8 3 1/2 22 13 25 7/8 4 @ 6,851#
43’ GLC4000-28 (S or AL)-43GLCS4000-28 (S or AL)-43
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
25’-0”25’-0”
3232
11 7/1629 7/16
14 1/232 1/2
23 3/823 3/8
3 1/23 1/2
-18
1919
25 7/825 7/8
24 @ 5,928#6 @ 6,342#
53’GLC4000-28 (S or AL)-53
GLCS4000-28 (S or AL)-53GLCSL4000-28 (S or AL)-53
SteelSteelSteel
4’20’25’
3 3/83 3/83 3/8
15 1/1615 1/1615 1/16
25’-0”25’-0”25’-0”
323232
11 7/1629 7/1631 7/16
14 1/232 1/234 1/2
23 3/823 3/823 3/8
3 1/23 1/23 1/2
-1820
191919
25 7/825 7/825 7/8
30 @ 5,928#8 @ 6,342#6 @ 6,583#
63’ GLC4000-28 (S or AL)-63GLCS4000-28 (S or AL)-63
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
25’-0”25’-0”
3232
11 7/1629 7/16
14 1/232 1/2
23 3/823 3/8
3 1/23 1/2
-18
2626
25 7/825 7/8
34 @ 5,928#8 @ 6,342#
64’ GLCSLX4000-28 (S or AL)-64 Steel 30’ 3 3/8 15 1/16 25’-0” 44 3/16 32 7/16 35 1/2 23 3/8 3 1/2 22 54 25 7/8 6 @ 6,851#78’ GLCSL4000-28 (S or AL)-78 Steel 25’ 3 3/8 15 1/16 25’-0” 44 3/16 31 7/16 34 1/2 23 3/8 3 1/2 20 54 25 7/8 8 @ 6,583#
83’ GLC4000-28 (S or AL)-83GLCS4000-28 (S or AL)-83
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
25’-0”25’-0”
44 3/1644 3/16
11 7/1629 7/16
14 1/232 1/2
23 3/823 3/8
3 1/23 1/2
-18
5454
25 7/825 7/8
44 @ 5,928#10 @ 6,342#
94’ GLCSLX4000-28 (S or AL)-94 Steel 30’ 3 3/8 15 1/16 25’-0” 44 3/16 32 7/16 35 1/2 23 3/8 3 1/2 22 54 25 7/8 8 @ 6,851#
103’GLC4000-28 (S or AL)-103
GLCS4000-28 (S or AL)-103GLCSL4000-28 (S or AL)-103
SteelSteelSteel
4’20’25’
3 3/83 3/83 3/8
15 1/1615 1/1615 1/16
25’-0”25’-0”25’-0”
44 3/1644 3/1644 3/16
11 7/1629 7/1631 7/16
14 1/232 1/234 1/2
23 3/823 3/823 3/8
3 1/23 1/23 1/2
-1820
545454
25 7/825 7/825 7/8
54 @ 5,928#12 @ 6,342#10 @ 6,583#
124’ GLCSLX4000-28 (S or AL)-124 Steel 30’ 3 3/8 15 1/16 25’-0” 44 3/16 32 7/16 35 1/2 23 3/8 3 1/2 22 54 25 7/8 10 @ 6,851#
34’
28’ GLCSL4000-34 (S or AL)-28 Steel 25’ 3 3/8 15 1/16 30’-0” 36 31 7/16 34 1/2 25 3/8 3 1/2 20 13 25 7/8 4 @ 6,717#
33’ GLC4000-34 (S or AL)-33GLCS4000-34 (S or AL)-33
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
30’-0”30’-0”
3636
11 7/1629 7/16
14 1/232 1/2
25 3/825 3/8
3 1/23 1/2
-18
1313
25 7/825 7/8
20 @ 6,062#6 @ 6,475#
34’ GLCSLX4000-34 (S or AL)-34 Steel 30’ 3 3/8 15 1/16 30’-0” 36 32 7/16 35 1/2 25 3/8 3 1/2 22 13 25 7/8 4 @ 6,985#
43’ GLC4000-34 (S or AL)-43GLCS4000-34 (S or AL)-43
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
30’-0”30’-0”
3636
11 7/1629 7/16
14 1/232 1/2
25 3/825 3/8
3 1/23 1/2
-18
1919
25 7/825 7/8
24 @ 6,062#6 @ 6,475#
53’GLC4000-34 (S or AL)-53
GLCS4000-34 (S or AL)-53GLCSL4000-34 (S or AL)-53
SteelSteelSteel
4’20’25’
3 3/83 3/83 3/8
15 1/1615 1/1615 1/16
30’-0”30’-0”30’-0”
363636
11 7/1629 7/1631 7/16
14 1/232 1/234 1/2
25 3/825 3/825 3/8
3 1/23 1/23 1/2
-1820
191919
25 7/825 7/825 7/8
30 @ 6,062#8 @ 6,475#6 @ 6,717#
63’ GLC4000-34 (S or AL)-63GLCS4000-34 (S or AL)-63
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
30’-0”30’-0”
3636
11 7/1629 7/16
14 1/232 1/2
25 3/825 3/8
3 1/23 1/2
-18
2626
25 7/825 7/8
34 @ 6,062#8 @ 6,475#
64’ GLCSLX4000-34 (S or AL)-64 Steel 30’ 3 3/8 15 1/16 30’-0” 50 7/8 32 7/16 35 1/2 25 3/8 3 1/2 22 54 25 7/8 6 @ 6,985#78’ GLCSL4000-34 (S or AL)-78 Steel 25’ 3 3/8 15 1/16 30’-0” 50 7/8 31 7/16 34 1/2 25 3/8 3 1/2 20 54 25 7/8 8 @ 6,717#
83’ GLC4000-34 (S or AL)-83GLCS4000-34 (S or AL)-83
SteelSteel
4’20’
3 3/83 3/8
15 1/1615 1/16
30’-0”30’-0”
50 7/850 7/8
11 7/1629 7/16
14 1/232 1/2
25 3/825 3/8
3 1/23 1/2
-18
5454
25 7/825 7/8
44 @ 6,062#10 @ 6,475#
94’ GLCSLX4000-34 (S or AL)-94 Steel 30’ 3 3/8 15 1/16 30’-0” 50 7/8 32 7/16 35 1/2 25 3/8 3 1/2 22 54 25 7/8 8 @ 6,985#
103’GLC4000-34 (S or AL)-103
GLCS4000-34 (S or AL)-103GLCSL4000-34 (S or AL)-103
SteelSteelSteel
4’20’25’
3 3/83 3/83 3/8
15 1/1615 1/1615 1/16
30’-0”30’-0”30’-0”
50 7/850 7/850 7/8
11 7/1629 7/1631 7/16
14 1/232 1/234 1/2
25 3/825 3/825 3/8
3 1/23 1/23 1/2
-1820
545454
25 7/825 7/825 7/8
54 @ 6,062#12 @ 6,475#10 @ 6,717#
124’ GLCSLX4000-34 (S or AL)-124 Steel 30’ 3 3/8 15 1/16 30’-0” 50 7/8 32 7/16 35 1/2 25 3/8 3 1/2 22 54 25 7/8 10 @ 6,985#
*This column provides the total number of support hangers with the corresponding ver cal load applied by each support hanger (in pounds) based on the “L1” dimensions shown. Up to a 20” hanger drop will be provided by Gorbel. Addi onal hanger points or longer drops can be provided at an addi onal charge.
Gorbel® Ceiling Mounted Work Sta on Bridge Crane Kits include: bridge, runways, hoist trolley, end trucks, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel runway lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Sway bracing is required on all systems except fl ush mounted systems (by others). Sway bracing kits are available but not included in the crane kit. Hoist provided by others.
Dimensions are for reference only and are subject to change without no ce.
CEILING MOUNTED WORK STATION MONORAILISOMETRIC VIEW
55
Model Number:
Capacity: pounds
Bridge Length (L): (OAL)
Runway Length: (OAL)L1: Are the number of support assemblies provided suffi cient?(See “HANGERS” column on dimensional chart pages)
Type of hanger required: Standard hanger with up to 20 inch drop. Support beam fl ange width ___________ inches Flush mounted, parallel Support beam fl ange width ___________ inches Flush mounted, perpendicular Support beam fl ange width ___________ inches Special hangersNote: Sway bracing is required on all systems except fl ush mounted systems. Sway bracing kits are available but are not included in the crane kit.
C: inches (hoist by others)
Gorbel® Monorails include: monorails, hoist trolley, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel monorail lengths greater than 63 feet and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Addi onal hanger points or longer drops, in excess of 20 inches, can be provided at an addi onal cost (hoist and sway bracing by others). Sway bracing kits are available but are not included in the crane kit.
Dimension and design details subject to change without no ce.CEI
LIN
G M
OU
NTE
D W
OR
KST
ATIO
N M
ON
OR
AIL
L1
L7
MONORAIL LENGTH
L1
L1
L1
L1
L7
GLMSTEEL MONORAIL
ALMALUMINUM MONORAIL
L1
MONORAIL LENGTH
GLMS(SL,SLX)STEEL MONORAIL
L1
L1
L7
L1
MONORAIL LENGTH
CEILIN
G M
OU
NTED
WO
RK
STATION
MO
NO
RA
ILSCEILING MOUNTED WORK STATION
MONORAIL
56
Model Number:
Capacity: pounds
Bridge Length (L): (OAL)
Runway Length: (OAL)L1: Are the number of support assemblies provided suffi cient?(See “HANGERS” column on dimensional chart pages)
Type of hanger required: Standard hanger with up to 20 inch drop. Support beam fl ange width ___________ inches Flush mounted, parallel Support beam fl ange width ___________ inches Flush mounted, perpendicular Support beam fl ange width ___________ inches Special hangersNote: Sway bracing is required on all systems except fl ush mounted systems. Sway bracing kits are available but are not included in the crane kit.
C: inches (hoist by others)Gorbel® Monorails inlcude: monorails, hoist trolley, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel monorail lengths great-er than 63 feet and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Addi onal hanger points or longer drops, in excess of 20 inches, can be provided at an addi onal cost (hoist and sway bracing by others). Sway bracing kits are available but are not included in the crane kit.
Dimension and design details subject to change without no ce.
H2
L3
12” L1 L1 L1MONORAIL LENGTH
8” MAX
L1 L1
SPLICE JOINT
HANGER
L1 12”
L3
L7
HOIST TROLLEY
GLM STEEL MONORAIL
H2
L3
L1
RUNWAY LENGTH
48”MAXSPLICE JOINT
AND PLATE
HANGERL1
L3
L7
GLMS, GLMSL, GLMSLXSTEEL MONORAIL
H1
18” 18”
CT1
HOIST TROLLEY
CT1
H2
L3
18”MONORAIL LENGTH
30” MAX
L1 L1
SPLICE JOINT
HANGER18”
L3
L7
HOIST TROLLEY
GLM STEEL MONORAIL
CT1
57
250#-500# CAPACITYCEILING MOUNTED WORK STATION MONORAILS
250#
CAP
ACIT
Y
MONORAIL LENGTH
MONORAIL LENGTH
TRACK MATL.
MAXL1
T1in
H1in
H2in
L3in
L7in
HANGERS(See Note)*
11’-6”GLM250-11.5
GLMS250-11.5ALM250-11.5
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
-9-
1 3/41 3/4
8
5 1/165 1/167 3/16
999
3 @ 366#2 @ 449#2 @ 430#
23’GLM250-23
GLMS250-23ALM250-23
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
-9-
1 3/41 3/4
8
5 1/165 1/167 3/16
99
14
5 @ 366#2 @ 449#2 @ 430#
28’ GLMSL250-28 Steel 25’ 1 1/2 11 1 3/4 5 1/16 9 2 @ 561#
33’GLM250-33
GLMS250-33ALM250-33
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
-9-
1 3/41 3/4
8
5 1/165 1/167 3/16
99
20
7 @ 366#3 @ 449#3 @ 430#
43’GLM250-43
GLMS250-43ALM250-43
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
-9-
1 3/41 3/4
8
5 1/165 1/167 3/16
131327
8 @ 366#3 @ 449#3 @ 430#
53’
GLM250-53GLMS250-53
ALM250-53GLMSL250-53
SteelSteelAlumSteel
6’20’20’25’
1 1/21 1/2
2 11/161 1/2
-9-
11
1 3/41 3/4
81 3/4
5 1/165 1/167 3/165 1/16
13133013
11 @ 366#4 @ 449#4 @ 430#3 @ 561#
63’GLM250-63
GLMS250-63ALM250-63
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
-9-
1 3/41 3/4
8
5 1/165 1/167 3/16
191937
12 @ 366#4 @ 449#4 @ 430#
78’ GLMSL250-78 Steel 25’ 1 1/2 11 1 3/4 5 1/16 54 4 @ 561#
83’GLM250-83
GLMS250-83ALM250-83
SteelSteelAlum
6’20’20’
1 1/21 1/2
2 11/16
-9-
1 3/41 3/4
8
5 1/165 1/167 3/16
545447
16 @ 366#5 @ 449#5 @ 430#
103’
GLM250-103GLMS250-103
ALM250-103GLMSL250-103
SteelSteelAlumSteel
6’20’20’25’
1 1/21 1/2
2 11/161 1/2
-9-
11
1 3/41 3/4
81 3/4
5 1/165 1/167 3/165 1/16
54545354
20 @ 366#6 @ 449#6 @ 430#5 @ 561#
500#
CAP
ACIT
Y
MONORAIL LENGTH MONORAIL LENGTH TRACK
MATL.MAX
L1T1in
H1in
H2
L3in
L7in
HANGERS(See Note)*
11’-6”GLM500-11.5
GLMS500-11.5ALM500-11.5
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
-10-
2 3/82 3/8
10
7 1/87 1/8
7 3/16
999
3 @ 725#2 @ 849#2 @ 794#
23’GLM500-23
GLMS500-23ALM500-23
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
-10-
2 3/82 3/8
10
7 1/87 1/8
7 3/16
99
14
5 @ 725#2 @ 849#2 @ 794#
28’ GLMSL500-28 Steel 25’ 2 13/16 12 3/8 2 3/8 7 1/8 9 2 @ 968#
33’GLM500-33
GLMS500-33ALM500-33
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
-10-
2 3/82 3/8
10
7 1/87 1/8
7 3/16
99
20
7 @ 725#3 @ 849#3 @ 794#
34’ GLMSLX500-34 Steel 30’ 2 13/16 14 3/8 2 3/8 7 1/8 9 2 @ 1,031#
43’GLM500-43
GLMS500-43ALM500-43
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
-10-
2 3/82 3/8
10
7 1/87 1/8
7 3/16
131327
8 @ 725#3 @ 849#3 @ 794#
53’
GLM500-53GLMS500-53
ALM500-53GLMSL500-53
SteelSteelAlumSteel
6’20’20’25’
2 13/162 13/162 11/162 13/16
-10-
12 3/8
2 3/82 3/8
102 3/8
7 1/87 1/8
7 3/167 1/8
13133013
11 @ 725#4 @ 849#4 @ 794#3 @ 968#
63’GLM500-63
GLMS500-63ALM500-63
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
-10-
2 3/82 3/8
10
7 1/87 1/8
7 3/16
191937
12 @ 725#4 @ 849#4 @ 794#
64’ GLMSLX500-64 Steel 30’ 2 13/16 14 3/8 2 3/8 7 1/8 46 3 @ 1,031@78’ GLMSL500-78 Steel 25’ 2 13/16 12 3/8 2 3/8 7 1/8 54 4 @ 968#
83’GLM500-83
GLMS500-83ALM500-83
SteelSteelAlum
6’20’20’
2 13/162 13/162 11/16
-10-
2 3/82 3/8
10
7 1/87 1/8
7 3/16
545447
16 @ 725#5 @ 849#5 @ 794#
94’ GLMSLX500-94 Steel 30’ 2 13/16 14 3/8 2 3/8 7 1/8 54 4 @ 1,031@
103’
GLM500-103GLMS500-103
ALM500-103GLMSL500-103
SteelSteelAlumSteel
6’20’20’25’
2 13/162 13/162 11/162 13/16
-10-
12 3/8
2 3/82 3/8
102 3/8
7 1/87 1/8
7 3/167 1/8
54545354
20 @ 725#6 @ 849#6 @ 794#5 @ 968#
124’ GLMSLX500-124 Steel 30’ 2 13/16 14 3/8 2 3/8 7 1/8 54 5 @ 1,031#
*This column provides the total number of support hangers with the corresponding ver cal load applied by each support hanger (in pounds) based on the “L1” dimensions shown. Up to a 20” hanger drop will be provided by Gorbel. Addi onal hanger points or longer drops can be provided at an addi onal charge.
Gorbel® Monorail Kits include: monorail track, hoist trolley, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel monorail lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Sway bracing is required on all systems except fl ush mounted systems (by others). Sway bracing kits are available but not included in the crane kit. Hoist provided by others.
Dimensions are for reference only and are subject to change without no ce.
CEI
LIN
G M
OU
NTE
D W
OR
KST
ATIO
N M
ON
OR
AIL
CEILIN
G M
OU
NTED
WO
RK
STATION
MO
NO
RA
ILS
58
1000#-2000# CAPACITYCEILING MOUNTED WORK STATION MONORAILS
1000
# CA
PACI
TY
MONORAIL LENGTH MONORAIL LENGTH TRACK
MATL.MAX
L1T1in
H1in
H2
L3in
L7in
HANGERS(See Note)*
11’-6”GLM1000-11.5
GLMS1000-11.5ALM1000-11.5
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
-11 1/16
-
3 1/163 1/16
11
7 7/87 7/8
7 13/16
99
13
3 @ 1,438#2 @ 1,645#2 @ 1,569#
23’GLM1000-23
GLMS1000-23ALM1000-23
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
-11 1/16
-
3 1/163 1/16
11
7 7/87 7/8
7 13/16
99
28
5 @ 1,438#2 @ 1,645#2 @ 1,569#
28’ GLMSL1000-28 Steel 25’ 3 1/8 13 15/16 3 1/16 7 7/8 13 2 @ 1,752#
33’GLM1000-33
GLMS1000-33ALM1000-33
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
-11 1/16
-
3 1/163 1/16
11
7 7/87 7/8
7 13/16
131339
7 @ 1,438#3 @ 1,645#3 @ 1,569#
34’ GLMSLX1000-34 Steel 30’ 3 1/8 17 1/16 3 1/16 7 7/8 13 2 @ 1,925#
43’GLM1000-43
GLMS1000-43ALM1000-43
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
-11 1/16
-
3 1/163 1/16
11
7 7/87 7/8
7 13/16
191949
8 @ 1,438#3 @ 1,645#3 @ 1,569#
53’
GLM1000-53GLMS1000-53
ALM1000-53GLMSL1000-53
SteelSteelAlumSteel
6’20’20’25’
3 1/83 1/82 5/83 1/8
-11 1/16
-13 15/16
3 1/163 1/16
113 1/16
7 7/87 7/8
7 13/167 7/8
19195319
11 @ 1,438#4 @ 1,645#4 @ 1,569#3 @ 1,752#
63’GLM1000-63
GLMS1000-63ALM1000-63
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
-11 1/16
-
3 1/163 1/16
11
7 7/87 7/8
7 13/16
262653
12 @ 1,438#4 @ 1,645#4 @ 1,569#
64’ GLMSLX1000-64 Steel 30’ 3 1/8 17 1/16 3 1/16 7 7/8 54 3 @ 1,925#78’ GLMSL1000-78 Steel 25’ 3 1/8 13 15/16 3 1/16 7 7/8 54 4 @ 1,752#
83’GLM1000-83
GLMS1000-83ALM1000-83
SteelSteelAlum
6’20’20’
3 1/83 1/82 5/8
-11 1/16
-
3 1/163 1/16
11
7 7/87 7/8
7 13/16
545453
16 @ 1,438#5 @ 1,645#5 @ 1,569#
94’ GLMSLX1000-94 Steel 30’ 3 1/8 7 1/16 3 1/16 7 7/8 54 4 @ 1,925#
103’
GLM1000-103GLMS1000-103
ALM1000-103GLMSL1000-103
SteelSteelAlumSteel
6’20’20’25’
3 1/83 1/82 5/83 1/8
-11 1/16
-13 15/16
3 1/163 1/16
113 1/16
7 7/87 7/8
7 13/167 7/8
54545354
20 @ 1,438#6 @ 1,645#6 @ 1,569#5 @ 1,752#
124’ GLMSLX1000-124 Steel 30’ 3 1/8 7 1/16 3 1/16 7 7/8 54 5 @ 1,925#
2000
# CA
PACI
TY
MONORAIL LENGTH MONORAIL LENGTH TRACK
MATL.MAX
L1T1in
H1in
H2
L3in
L7in
HANGERS(See Note)*
11’-6”GLM2000-11.5
GLMS2000-11.5ALM2000-11.5
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
-12-
3 1/23 1/2
13 1/4
8 1/168 1/16
8
99
13
3 @ 2,855#2 @ 3,138#2 @ 3,004#
23’GLM2000-23
GLMS2000-23ALM2000-23
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
-12-
3 1/23 1/2
13 1/4
8 1/168 1/16
8
99
26
5 @ 2,855#2 @ 3,138#2 @ 3,004#
28’ GLMSL2000-28 Steel 25’ 2 7/8 15 3/8 3 1/2 8 1/16 13 2 @ 3,285#
33’GLM2000-33
GLMS2000-33ALM2000-33
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
-12-
3 1/23 1/2
13 1/4
8 1/168 1/16
8
131339
7 @ 2,855#3 @ 3,138#3 @ 3,004#
34’ GLMSLX2000-34 Steel 30’ 2 7/8 18 3 1/2 8 1/16 13 2 @ 3,404#
43’GLM2000-43
GLMS2000-43ALM2000-43
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
-12-
3 1/23 1/2
13 1/4
8 1/168 1/16
8
191949
8 @ 2,855#3 @ 3,138#3 @ 3,004#
53’
GLM2000-53GLMS2000-53
ALM2000-53GLMSL2000-53
SteelSteelAlumSteel
6’20’20’25’
2 7/82 7/82 3/82 7/8
-12-
15 3/8
3 1/23 1/2
13 1/43 1/2
8 1/168 1/16
88 1/16
19195319
11 @ 2,855#4 @ 3,138#4 @ 3,004#3 @ 3,285#
63’GLM2000-63
GLMS2000-63ALM2000-63
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
-12-
3 1/23 1/2
13 1/4
8 1/168 1/16
8
262653
12 @ 2,855#4 @ 3,138#4 @ 3,004#
64’ GLMSLX2000-64 Steel 30’ 2 7/8 18 3 1/2 8 1/16 54 3 @ 3,404#78’ GLMSL2000-78 Steel 25’ 2 7/8 15 3/8 3 1/2 8 1/16 54 4 @ 3,285#
83’GLM2000-83
GLMS2000-83ALM2000-83
SteelSteelAlum
6’20’20’
2 7/82 7/82 3/8
-12-
3 1/23 1/2
13 1/4
8 1/168 1/16
8
545453
16 @ 2,855#5 @ 3,138#5 @ 3,004#
94’ GLMSLX2000-94 Steel 30’ 2 7/8 18 3 1/2 8 1/16 54 4 @ 3,404#
103’
GLM2000-103GLMS2000-103
ALM2000-103GLMSL2000-103
SteelSteelAlumSteel
6’20’20’25’
2 7/82 7/82 3/82 7/8
-12-
15 3/8
3 1/23 1/2
13 1/43 1/2
8 1/168 1/16
88 1/16
54545354
20 @ 2,855#6 @ 3,138#6 @ 3,004#5 @ 3,285#
124’ GLMSLX2000-124 Steel 30’ 2 7/8 18 3 1/2 8 1/16 54 5 @ 3,404#
*This column provides the total number of support hangers with the corresponding ver cal load applied by each support hanger (in pounds) based on the “L1” dimensions shown. Up to a 20” hanger drop will be provided by Gorbel. Addi onal hanger points or longer drops can be provided at an addi onal charge.
Gorbel® Monorail Kits include: monorail track, hoist trolley, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel monorail lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Sway bracing is required on all systems except fl ush mounted systems (by others). Sway bracing kits are available but not included in the crane kit. Hoist provided by others.
Dimensions are for reference only and are subject to change without no ce.
59
4000# CAPACITYCEILING MOUNTED WORK STATION MONORAILS
4000
# CA
PACI
TY
MONORAIL LENGTH MONORAIL LENGTH TRACK
MATL.MAX
L1T1in
H1in
H2
L3in
L7in
HANGERS(See Note)*
23’ GLM500-23GLMS500-23
SteelSteel
4’20’
3 3/83 3/8
-18
3 1/23 1/2
15 1/1615 1/16
99
7 @ 5,637#2 @ 6,014#
28’ GLMSL500-28 Steel 25’ 3 3/8 20 3 1/2 15 1/16 13 2 @ 6,256#
33’ GLM500-33GLMS500-33
SteelSteel
4’20’
3 3/83 3/8
-18
3 1/23 1/2
15 1/1615 1/16
1313
10 @ 5,637#3 @ 6,014#
34’ GLMSLX500-34 Steel 30’ 3 3/8 22 3 1/2 15 1/16 13 2 @ 6,523#
43’ GLM500-43GLMS500-43
SteelSteel
4’20’
3 3/83 3/8
-18
3 1/23 1/2
15 1/1615 1/16
1919
12 @ 5,637#3 @ 6,014#
53’GLM500-53
GLMS500-53GLMSL500-53
SteelSteelSteel
4’20’25’
3 3/83 3/83 3/8
-1820
3 1/23 1/23 1/2
15 1/1615 1/1615 1/16
191919
15 @ 5,637#4 @ 6,014#3 @ 6,523#
63’ GLM500-63GLMS500-63
SteelSteel
4’20’
3 3/83 3/8
-18
3 1/23 1/2
15 1/1615 1/16
2626
17 @ 5,637#4 @ 6,014#
64’ GLMSLX500-64 Steel 30’ 3 3/8 22 3 1/2 15 1/16 54 3 @ 6,523#78’ GLMSL500-78 Steel 25’ 3 3/8 20 3 1/2 15 1/16 54 4 @ 6,256#
83’ GLM500-83GLMS500-83
SteelSteel
4’20’
3 3/83 3/8
-18
3 1/23 1/2
15 1/1615 1/16
5454
22 @ 5,637#5 @ 6,014#
94’ GLMSLX500-94 Steel 30’ 3 3/8 22 3 1/2 15 1/16 54 4 @ 6,523#
103’GLM500-103
GLMS500-103GLMSL500-103
SteelSteelSteel
4’20’25’
3 3/83 3/83 3/8
-1820
3 1/23 1/23 1/2
15 1/1615 1/1615 1/16
545454
27 @ 5,637#6 @ 6,014#5 @ 6,256#
124’ GLMSLX500-124 Steel 30’ 3 3/8 22 3 1/2 15 1/16 54 5 @ 6,523#
*This column provides the total number of support hangers with the corresponding ver cal load applied by each support hanger (in pounds) based on the “L1” dimensions shown. Up to a 20” hanger drop will be provided by Gorbel. Addi onal hanger points or longer drops can be provided at an addi onal charge.
Gorbel® Monorail Kits include: monorail track, hoist trolley, end stops, fl at wire festooning, festoon gliders (festoon trolleys on steel monorail lengths greater than 63’ and all aluminum systems), festoon stack-up sec on, splice joints and hanger brackets. Sway bracing is required on all systems except fl ush mounted systems (by others). Sway bracing kits are available but not included in the crane kit. Hoist provided by others.
Dimensions are for reference only and are subject to change without no ce.
CEI
LIN
G M
OU
NTE
D W
OR
KST
ATIO
N M
ON
OR
AIL