worldwide distribution - renox · worldwide distribution. 1) ... (welding, slag, grindings)....

Simple Solutions are the BEST!ISO 9000

1-877-888-8727 www.OneEyeIndustries.com 1-403-242-4221

Since 2004

Worldwide Distribution

1) Why is magnetic filtration of value? Quality magnetic filters are capable of filtering to submicron levels without flow restriction and are reusable for 10+ years. The most damaging contaminant in engine lube, hydraulic fluid, fuel and coolant is ferrous metal under 10 microns.

2) How do you collect non ferrous contamination on a magnetic filter? Through static adhesion caused by static charge build up with the high flow fluids and or gases. Also through entrainment which occurs when a particle of ferrous contamination gets embedded in the non-ferrous particle allowing the magnetic filter to capture the entire mass.

3) What types of magnetic filters are there? The most common are ceramic which have been used to filter oil and fluids for the past 50 years. The new magnetic filters use rare earth magnets in the magnetic filters.

4) What is the difference between ceramic and rare earth magnetic? Ceramics are low in magnetic strength and will crack and disassemble when exposed to vibration. They also lose their magnetic field strength when exposed to high heat. Exposed ceramic is also very hard to clean.

Rare earth magnets are 4 times stronger than ceramic magnets and handle high heat without losing field strength and are highly resistant to vibration. They are coated and do not crack. They are installed in stainless steel tubes, retain their strength and clean very easily. 5) What are the advantages of OEI magnetic filters? OEI magnetic filters are manufactured with our patented design and are 12 times stronger than ceramic magnetic filters; they are encased in stainless steel tubes in a patented format that creates powerful projected radial fields that have larger surface area than traditional magnetic filter rods. 6) How do you clean a magnetic filter rod? The OEI magnetic filter rod design has no magnetic field at the end thereby you slide the contamination down to the end and it falls off. 7) What do you do with contamination collected? It is recommended to have the trapped contamination analyzed for wear debris identification. The magnetic filter becomes a predictive maintenance tool.

8) Can I purchase your product directly? We have distribution in most locations around the world and if we do not cover your area, yes we will supply direct.

9) Custom designs? Yes we welcome custom designs.

10) What happens if you remove all the metal out of oil? Our magnetic filters remove the ferrous and in many applications the non ferrous contamination to submicron levels due to static adhesion but you will never remove all the metal as it is produced by moving metal parts, new oils and fluids are contaminated with metal and air ingression contaminates the system with fine metal particles under 10 microns. If you are tracking the contamination levels through oil analysis and install magnetic filters you will simply drop your bench mark levels much lower. The less hard metals results in less wear thereby extended component and fluid/oil life.

11) How long do magnetic filters last? OEI magnetic filters have a 10+ year life expectancy.

ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Padswww.OneEyeIndustries.com

F.A.Q.

Magnetic Filter Cores A novel approach to proactive maintenanceBy Christian Bauer, Pall Corporation and Roger Simonson, One Eye Industries

The generation of ferrous contaminants in most hydraulic and lube sys-

tems due to both normal and abnormal wear is a fact of life. Knowing the

amount and type of wear particles in the fluid system is paramount to avoid-

ing unscheduled outages. Standard filter elements will capture any type of

particulate contamination, ferrous and non-ferrous, within their media matrix

according to their micron rating. Identification of the contamination captured

typically requires off-site laboratory analyses.

Built-in magnetic filter cores can capture ferrous contaminants in fluid systems,

down to < 1 µm, before they reach the actual filter, thus providing an excel-

lent diagnostic tool for contamination monitoring and proactive maintenance.

Due to static adhesion, the cores can also retain some of the non-ferrous

contaminants. By simply removing the magnetic core and examining the

contamination retained on it under a microscope, reliability and maintenance

engineers across many industries now have a valuable tool for identifying

potential wear-related issues before they become a real problem.

Pall CorporationPALL

Reusable Oil Filter Magnets

www.OneEyeIndustries.com

Mission Statement

To design and manufacture the most effective cost efficient filtration systems in the world and answer the challenges the industry presents.

To grow our company into an international supplier through strategic partnerships with quality companies who operate on a similar high level of integrity and commitment.

With a dedicated effort, increase the application of our filtration solutions to improve industry efficiency thereby reduce overall dependency on fossil fuels and a reduction of harmful emissions that result from our industrial revolution.

About UsOne Eye Industries Inc welcomes its 17th year in business. With 4 years of product development and entering our 13th year of sales, our product lines continue to grow to answer the demand and expanding customer base around the world in every industry.

We manufacture an extensive product line utilizing new magnet technology. Our filters work with and compliment existing filtration systems and or replace them with reusable stainless screen filters. Custom designs are welcome.

Industry has been reluctant to employ magnetic filtration due to years of exposure to ineffective design and limited magnetic ability. Recent technological advances in magnetic properties and manufacturing processes have resulted in smaller, stronger high tech magnets available that allow innovative new designs for filtration systems and dramatically improve traditional magnetic filtration.

Industry research states “Iron and Steel” particles under 10 microns in size are the most damaging contaminants in air compression, water, lubrication, hydraulic fluid, coolant and fuel systems. The rate at which contamination enters these systems is greatly underestimated and understated. Likewise, the effectiveness of traditional filters at removing metal contaminants is greatly overstated. Magnetic filtration has practical and beneficial applications for all industry: chemical processing, oil & gas refining, manufacturing, construction equipment, transportation, food & pharmaceuticals, marine and pulp & paper.

Our first line: reusable magnetic filters that compliment and work with existing disposable filters. They attach to the outer skin, extract and trap contaminants to the interior filter skin.

Our second line: magnetic rods and scrubber filters install in-tank, or inline. They offer maximum filtration, no bypassing with minimal flow restriction, low & high- pressure applications with ten plus years of service.

Our third line: the ADD-Vantage 9000 series are heavy-duty reusable stainless screen filters equipped with an internal magnetic filter and an internal fail-safe by-pass. When the bypass is activated the fluid is still filtered by the magnetic filter. They are environmentally friendly with ten plus years of service.

All our products offer long life, are user friendly, easily cleaned, reusable and maintained with minimal effort and cost. Cleaner fuel and lubricants for all applications in industry will result in reduced maintenance costs and increased productivity. This will reduce the demand on industry to produce and use more energy that results in increased emissions.

R.M. Simonson

Founder, President & CEO

Table of Contents

1

ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads

1000 SeriesReusable Magnetic Filter Pads 3 sizes available for oil, fuel, transmission and hydraulic disposable spin-on filters

Page 9


One Eye Industries Inc. assures:• Consistent Quality (ISO 9000) • Leading Technical Innovation • Premier Customer ServiceOEI manufactures environmentally friendly filtration systems with proprietary magnetic technology. Reusable long life filters that allow extended maintenance schedules, increased fluid and equipment component life.

From Consumer to IndustrialOEI provides solutions to retail consumers and to industrial users in the Oil & Gas, Marine, Manufacturing, Mining and associated industries to effectively filter and remove ferrous and non-ferrous contamination in lube oil, hydraulic fluid, fuel, coolant, gear oil, glycol, process/effluent water and chemicals.

Product LinesMagnetic Filter Pads: Attaches to and compliments existing disposable filters for lube oil, fuel, hydraulics, and coolants applications. Magnetic Filter Rods & Scrubbers: Multiple designs for inline and reservoir applications with or without traditional filtration.ADD Vantage 9000 Series: Designed to replace disposable filters, combining two filtration technologies in one filter. Cleanable true absolute rated Stainless Steel elements and patented magnetic filter technology results in a highly effective environmentally friendly filter.

Why Filter Ferrous Contaminants?Removal of ferrous contaminants (iron, steel, etc) will dramatically reduce the damaging wear cycle, extending the life of the fluids and equipment.Studies show ferrous particles smaller than 10 microns will generate 3 to 5 times more wear than larger particles.Equipment is being manufactured with tighter tolerances causing a demand for higher filtration requirements to sub-micron levels. These contaminants are carried into high pressure contact areas causing damage to softer metals, seals, bearings and gaskets.The use of extremely strong magnetic fields, are required to trap these particles, especially in “high flow” and or high viscous fluids.OEI’s patented magnetic technology traps ferrous and non-ferrous contaminants to sub-micron in size.In many cases this is the first time credible filtration has been achieved to this level.

2000 • 2500 • 3000 SeriesMagnetic Filter Rods For installation inside of elements, tanks and reservoirs for both static and mobile equipment

Page 10-14

7000 SeriesMagnetic Plugs

Replacement drain or level plug for final drives, rear ends, transfer cases and transmissions

Page 23

5000 SeriesMagnetic Filter ScrubberMagnetic Y-Strainer For inline installation allowing for easy cleaning and no flow restriction

Page 17-22

8000 SeriesCustomized Filtration SystemsKidney loop, High Flow FiltrationHydrostatic Lube Lift

Page 24-27

ADD-Vantage 9000The most advanced filter technology for fluids in the world.Enviro- Wash 9000

Page 28-36

4000 SeriesMagnetic Funnel Scrubber

Food and Industrial Grade inline filtration

Page 15 & 16

What's New! New Products for a variety of applications

Page 2-8


2

ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on PadsISO 9000 • Reusable • 3 Year Warranty • 10+ Year Lifewww.OneEyeIndustries.com

Magnetic Filter Patches

Magnetic Patch

The Magnetic Patch is a temporary solution designed to plug off holes in piping, drop chutes and silos allowing production to be maintained. It is easily installed and removed during a scheduled down time. Ideal for spill kits in liquids and solids applications. The Magnetic patch comes in three sizes and can be cut into smaller sizes to accommodate smaller holes and pipes. Custom sizes and designs are available for slurry product applications and high temperature applications up to 300F.

A quick & secure way of repairing holes in:

- Steel Pipe - Round Radius Elbows - Flat Back Elbows – Silos - Chutes

Model Number Dimensions 1MP409 - 4" x 9" x 3/8" 1MP813 - 8" x 13" x 3/8" 1MP1713 - 17" x 13" x 3/8"

N E W !

Magnetic Sweeper25R14TH36

OEI introduces the magnetic sweeper which is designed to remove ferrous fillings and debris to sub-micron levels from new storage reservoirs created through the manufacturing process (welding, slag, grindings). Another application is cleaning fabrication flooring around work stations. CNC milling machine reservoirs can also be cleaned using this product.

This unit is designed to be used like a broom with a 36” reach x 14” wide you are able to move the magnetic sweeper throughout areas collecting the ferrous contamination. The flexible fiberglass handle is 36” in length and allows you to reach under and around tables and equipment. Simply clean the magnetic sweeper rod by wiping it with a clean cloth.

Magnetic Sweeper


3


Parker ModuFlow, BGT, RF72 & Guardian GT4 Magnetic Filters


Pall Magnetic Filters

PALL Marksman Series

OEI has manufactured a magnetic filter specifically for the Parker "Moduflow Plus IL2/RF2/CF2 Series", BGT 1210QLB-GEF2321, RF72 and Guardian GT4 at the request of our customers. The magnetic filter is easily installed and removed for inspection and cleaning. As with all OEI magnetic filters this will enhance your fluid cleanliness and extend equip-ment life.

Guardian GT4

OEI PART # - 2RNC384TH

ModuFlow "Plus" IL2/RF2/CF2 Series

Single Element - 2RMFP7Double Element - 2RMFP17

Size OEI Part #1 Bag 3RT12PALLT18652 Bag 3RT24PALLT186540 inch 3RT40PALLT1865

PALL HF SeriesSize OEI Part #20 inch 3RT20PALLHF40 inch 3RT40PALLHF60 inch 3RT60PALLHF

OEI has manufactured a magnetic filter specifically for the PALL "Marksman & HF Series" at the request of our custom-ers. the magnetic filter is easily installed and removed for inspection and cleaning. As with all OEI magnetic filters this will enhance your fluid cleanliness and extend equipment life.

Foot Rest to protect the element Handle Clamp

Original RF72

OEI PART # - 25RF72

BGT 1210QLBGEF2321

OEI PART # - 3RPBGT12

N E W !

For the Original Moduflow IL2 Series OEI has created

the 2RMFD334


4


OEI is pleased to announce that we are now offering magnetic filter replacement parts for PTI Technologies’ Model F8G-150, Model F5D-150, and F2P-120 Series filters.

PTI Magnetic Filters


N E W !

PTI Filter Model F2P - 120 Series PTI Filter Model F8G150

Magnetic Filter Rod 2RC1212C134Reusable Element 9ELPT120x25

Magnetic Filter Rod 3RF8G150Reusable Element 9ELPT815x25

PTI Filter Model FD-150Magnetic Filter Rod 3RF5D150Reusable Element 9ELPT10000x25

Schroeder & Stauff Magnetic Filters

OEI has manufactured a magnetic filter specifically for Schroeder filter model QLF15-16 or 39 and Stauff SF300 Series Filters at the request of our customers. As with all OEI magnetic filters this will enhance your fluid cleanli-ness and extend equipment life.

Schroeder Filter Model QLF15-16 OR 39

Stauff Filter Model SF300

Schroeder Element OEI Magnetic Filter #16Q – 16PML 25RT14T31216QCL 25RT16T31239Q – 39QPML 25RT34T31239QCLQF 25RT36T312

Magnetic Filter Rod 2RC23C134

N E W !

5




Schroeder Magnetic K and RTI Series Filters

OEI has designed an array of magnetic filters to fit Schroeder RTI, KL3 and K9 Filter Housings. These stack-able filter systems can be designed in 1, 2, or 3 rod series with stainless steel coupler to fit K1, KK1, 27K1 and 1K-3K Models.

K9-HousingModel Single Element Stackable K1 Elements1K 2RC7C112 2K 2RC16C112 2RSCHK23K 2RC2515C112 2RSCHK3

KL3- HousingModel Single Element Stackable K1 Elements1K 2RC7C112 2K 2RC16C112 2RSCHK23K 2RC2512C112 2RSCHK3

Schroeder Magnetic CTF60 Series Filters

OEI is pleased to introduce their new magnetic filter for Schroeder CTF60 Series filters to enhance their filtration capability. With this improvement, as with all OEI filters, contamination will be re-moved from the system down to sub-micron levels extending fluid and component life.

N E W !

N E W !

RTI- HousingModel Single Element Stackable K1 ElementsK1 2RC614C112 KK1 2RC15C112 2RSCHK227K1 2RC2434C112 2RSCHK3

CTF60- HousingModel Single Element 5C 2RT4T1 8C 2RT6T114C 2RT13T1

2RC##C112

2RSCHK3 consist of 2RSCHK2 and

2RSCHK1

2RSCHK2

2RT##T1

6



25RCAT-1W1564

The 25RCAT-1W1564 and 2RC12C412 magnetic filters are designed to be installed in the 3512B and C175 engine sump screen filter (1W-1564 and 364-8521) enhancing its filtration capability to sub-micron levels with the use of OEI's patented magnetic technology.

The magnetic filter has been designed for easy installation, on the 25RCAT-1W1564 simply remove the bolt and washer #8-9, place the washer on the magnetic filter and use the magnetic filter to hold the sump screen in place. A Tee handle has been installed to assist with the installation. A circular support has been installed on the 25RC12C412 for ease of installation as well.


Industrial Filtration Solutions

CAT Sump Filter Enhancement

CAT Motor Grader Chain Case Magnetic Filtration System

16H, G, M Motor Grader1PCAT-4D7678NPT

OEI now offers the Motor Grader Chain Case Magnetic Filter with the inspection plate ready for installation on the 16H, G, M, and 24H, G, M.

These plates can also be ordered seperately.

24H, G, M Motor Grader1PCAT-1206157NPT

Magnetic Filter and inspection plate for CAT Motor GraderModel Part Number16H, G, M - 3R20HD78PL24H, G, M - 3R24HD78PL

CAT Filter EnhancementCAT Transmission Replacement Filter

25RCAT-7160 (with 3S-3439 Plate) 25RCAT-3251 (with 8P-3251 Plate)

The OEI magnetic filter is designed to replace the ceramic OEM magnetic filtration technology.

OEI’s powerful rare earth magnetic fields dramatically improve filtration of ferrous contamination to sub-micron levels.

25RC12C412N E W !

CAT Transmission Plate Filter Enhancement

25RCAT-9P5925OEI now offers a filter enhancement for the CAT 9P5925

Transmission Plate. This enhancement increases the filtration capability down to sub-micron levels offering increased fluid

and transmission component life.

N E W !

7


7

2RFCS787-2 or 2RFCS787-12(1/4" OR 5/16" Sample Tube) (1/2" Sample Tube)

OEI is pleased to announce an innovative way to filter and prevent ingression contamination in the Komatsu 830E wheel motors. This design is multipurpose; first it acts as a level monitor for the oil, second as a filter to remove the most damaging contaminant “ferrous metal” to sub-micron levels, and the third is a predictive maintenance tool, simply remove the trapped contamination from the magnetic filter and send it away to a lab for analysis.

The 4-in-1 Magnetic filter also has the added benefit of being able to extract an oil sample without removing the filler cap reducing the opportunity for foreign materials to enter. The test will identify premature wear patterns of the components and allow predictive maintenance scheduling.

Dip Stick

Magnetic FilterSample Port

OEI has designed a reusable Stainless Steel Element (9ELSS77532x25) to replace Komatsu's 209-60-77531 disposable element. OEI's stainless steel elements provide maxi-mum filtration protection, eliminating any chance of “channelling or worm holing” the ele-ment is reusable and available in 40, 25 or 10 micron β200 rating.

The 2RNC3810T3 magnetic filter is designed to be installed in the Hydraulic Element Filter (209-60-77532).

The magnetic filter has been designed for easy installation, simply remove the strainer and drill a 3/8" hole in the center bottom, attach the magnetic filter with (2) 3/8" washers, place (1) washer on the magnetic filter insert through the strainer and fasten with the 2nd washer and 3/8" nut. The tee handle is designed to keep the magnetic filter centered in the element.

Komatsu Hydraulic Filter Enhancement

Komatsu Wheel Motor Filtration

PC 1250 Enhanced Hydraulic Filtration

4 in 1 Magnetic Filter/ Level Monitor/ Sampling Port 2RFCS787- #

Magnetic Filter / Level Monitor25RFC787

1/2" diameter magnetic filter projecting multiple 3" radial fields

3/4" diameter magnetic filter projecting multiple 4" radial

fields

Komatsu Hydraulic Return Filter

Komatsu PC3000 thru PC8000 Hydraulic Return In-Tank Magnetic Filter Rod

The OEI magnetic filter is designed to replace the steel OEM rod (763 795 73). The 2RKOM-79573 duplicates that of the OEM part allowing for a perfect fit. The magnetic filter rod will increase filtration capability to sub-micron levels and is designed for easy installation. It enhances hydraulic fluid cleanliness and increases reliability by extending fluid and component life.

N E W !

8




Komatsu Magnetic Plug

7PKOM0086 Magnetic Plug

OEI has re-designed our original 7000 series magnetic plug to include 4 divots in the interior to

lock into a 3/4" ratchet or extension drive

Currently available in 1 1/4" Designed specifically for Komatsu machinery*

N E W !

Mud Mag

8K3R216MLFT Mud Mag

OEI has designed a magnetic trap for application in all open mud tanks for mud logging on offshore and onshore drilling rigs. This magnetic trap has been de-signed for both vertical and horizontal system inser-tion, has the most powerful magnetic fields on the market and is light weight for safe handling.

The unit includes a collection bag to collect particles without cross contamination. This contamination is analysed to determine drilling component wear to add a higher level of efficiency to the drilling opera-tion.

8K3R216MLFT Horizontal 8K3R216MLFT Vertical

N E W !

Pump JacksN E W !

OEI has designed magnetic filter rods for application on Lufkin Legrand, Weatherford Ampscot and other Pump Jack gearboxes to remove con-tamination down to sub-micron levels with no flow restriction, extend-ing fluid and component life.

OEI manufactures magnetic filter rods for 114, 160, 228, 320, 456, 640, 912, 1280 and 1824 Pump Jack Models. The magnetic filter rods are installed in the splash oil area and are attached to the inspection plate using either an NPT or cam-lock (optional self-locking) fastener. Custom designs and sizes are available upon request. Please contact us to match our filter rods to your gearbox model.

NPT Fastener

Cam-lock Fastener

1000 Series Magnetic Filter Pads

9


9

BT500 For all brands of disposable filters up to 3” in diameter• Small trans missions, rear-end dis posable filters, small fuel filters• Marine engines and recreational vehiclesBT800 For all brands of disposable filters 3”- 4“ in diameter. Fuel, engine oil, hydraulic , coolant and transmission filters.

BT900 For all brands of disposable filters 4” and up in diameter. Fuel, engine oil, hydraulic, coolant and transmission filters

OIL FILTER MAGNET

Multiple high strength magnetic fields trap damaging

microscopic ferrous and non-ferrous metal contaminants

that the filter cannot

OIL FILTER MAGNET

Magnetically attaches to disposable filters

Works with and compliments existing disposable filters by:

• Filtering ferrous and non-ferrous contamination to sub- micron levels• Removing the hard metals reduces wear on the softer components• Extending the lube oil, hydraulic and coolant fluids opera-tional life

MULTIPLEHIGH STRENGTH

MAGNETIC FIELDSTRAP DAMAGING

MICROSCOPIC METALCONTAMINANTSTHAT THE FILTER

CANNOT

OIL FILTER MAGNET

MAGNETICALLY ATTACHESTO DISPOSABLE FILTERS

OIL FILTER MAGNET

FM800OIL FILTER MAGNET

FM900OIL FILTER MAGNET

MAGNETIC FILTRATION SOLUTIONS

BT 900

2 3/8"60.3 MM

1/4" / 6.3 MM

2 3/8"60.3 MM

3"76.2 MM

6"152.4 MM

1/4" / 6.3 MM

3/8" / 6.3 MM

4"101.6 MM

6"152.4 MM

2 3/8"

1/4"

2 3/8"

3"

6"

1/4"

3/8"

4"

6"

1000 SERIES MAGNETIC FILTER PADS – For application on all types and sizes of disposable filters.

1MPBT500 Magnetic pad 2-3/8”W x 2-3/8”L x 1/4”T

1MPBT800 Magnetic pad 3” W x 6”L x 1/4”T

1MPBT900 Magnetic pad 4”W x 6”L x 3/8”T

ISO 9000 • Reusable • 1 Year Warranty on Pads • 10+ Year Life

Made in Canada

• No Tools Required

• Endure Temperature variance from -40 to 350 F

• Removal of contamination down to sub-micron levels will enhance fluid and equipment component life

60.3 mm

60.3 mm

6.3 mm

76.2 mm

152.4 mm

152.4 mm

6.3 mm

9.5 mm

101.6 mm

2000 • 2500 • 3000 • 3200 Series Magnetic Filter Rods

10


Attach inside transmission and hydraulic cartridge elements.

ISO 9000 • Reusable • 3 Year Warranty on Rods • 10+ Year Life

2000/2500/3000/3200 Series Magnetic Filter Rods are designed to be installed in reservoirs, gear boxes, filter elements, pipe lines and more. These Magnetic Filters will trap ferrous contaminants and non-ferrous contaminants (by static adhesion and entrainment) to sub-micron levels. Available in a variety of magnetic filter rod sizes and fasteners.

OEI manufactures all our Magnetic Filter Rods with 304/316 Stainless Steel Tubing (Monel and other Stainless grades are available). Rare Earth Magnets are installed in our patented method that creates the most powerful non-electric magnetic fields available. For filtration of Ferrous and Non-ferrous (hydro statically charged) contamination down to sub-micron levels in all fluids, gases, chips and powders etc. Designed to be user friendly (easily cleaned) long life (10+ years) of service, custom designs are welcome.

Install inline before sock filters to eliminate worm holing.

Install in tank at the inlet/outlet

Magnetic Filter Protective Cage

National Course or Metric Thread

Magnetic Base Cam-lock with Male Adapter

NPT, ORB, BSP or Metric Plug

Protective Cage

Magnetic Filter

OEI's protective cage is designed to aid in the installation and removal of the magnetic filter.

The protective cage is supplied with all 3R2 magnetic filters as a safety precaution due to the magnetic filters strength.

Box 1 Box 2

25RPC 12

Box 1MagneticFilter Size

2RPC - 1/2" Dia.

25RPC - 3/4" Dia.

3RPC - 1" Dia.

3R2PC - 2" Dia.

Box 2Magnetic

Filter Length

In Inches

How To Order .....

11



ISO 9000 • Reusable • 3 Year Warranty on Rods • 10+ Year Life

2000 • 2500 • 3000 • 3200 Series Magnetic Filter Rods

2000/2500/3000/3200 Series Magnetic Filter Rods

Box 4 Fastener Size5/16” NC-Only3/8” NC-Only1/2”5/8”3/4”1”

1 1/4”1 1/2”

2”10 mm Bolt Thread Only

12 mm Bolt Thread Only

14 mm

16 mm18 mm20 mm22 mm24 mm50 mm

Etc.

Blank for MB, MBA, DS, CL or Tee

Box 1 Box 2 Box 3 Box 4 Box 5 Box 6 Box 7 Box 8

25R NC 38 7 T 3 HD

Box 1 Magnetic Filter Rod2R 1/2” Diameter 25R 3/4” Diameter 3R 1” Diameter

3R2 2” DiameterIncludes Protective Cage Box 6 Fastener Tool

Blank NC, MB, MBA, CL or DS

IS Internal SquareES External SquareIH Internal HexEH External HexT Tee EndD Disk

TH ThumbC Circular Support

Box 2 TemperatureBlank 300F / 150CHH 600F / 300C

Box 3 FastenerNC Nation Course Thread

NPT Nation Pipe Thread

BSPP British Standard Pipe Parallel

BSPT British Standard Pipe Tapered

M Metric ThreadORB O-Ring BossMB Magnetic Base

MBA Magnetic Base AdjustableDS Dual StandCL Cam-LockT Tee

CU CustomAJ AdjustableIT Internal Thread (Female)C Circular Support

MT Metric Tapered

Box 5 Magnetic Length

Insert in Inches 3, 3 1/2, 4, 7, 12, 16, 24, etc.

Box 7 T or D LengthInsert in Inches1, 112, 134, 2, 3, 312, etc.

Box 8 Design Strength

Blank Stationary Equipment

HD Mobile EquipmentFG Food Grade

HP High Pressure (over 300 PSI)

MODEL CODE:

HOW TO ORDER:

* Custom Designs are Available

3RT12D312 25RNC387T3HD

ISO 9000 • Reusable • 3 Year Warranty Rods • 10+ Year Life


12


OEM Part Number Magnetic Filter Plugs & Magnetic Filter Rods OEI Part

NumberAtlas Copco

5541 506500

ST 1520 Scoop Truck 7PM3320EH

Custom ST 8B - Scoop Truck Hydraulic Tank 3R24HDAC2ES CAT

1W-1564 Magnetic Filter for Engine Sump Filter (1W-1564) 3/4" x 6" w/ 3/8"nc and 2.875 x 3/8" Support tee 25RCAT-1W1564

2A-3852 777 Final Drive/ Planetary, 789 / 793 Front Wheel Cover, 621 B Final Drive 7PCAT-3837

2A-3852 Custom Design - 4"long x 1/2" diameter - Magnetic filter on a 2A-3852 25RCAT-38522H-3865 Magnetic Drain Plug Inside Square 7PCAT-2H3865

3E-2338 For: 854G Rubber Dozer Engine, 5130B Excavator, 789 CAT Haul Truck Transmission, 793 CAT Haul Truck Trans-mission, 330 Excavator Final Drive, 621F CAT Scraper Final Drive Plug, 345 Excavator Final Drive, 375 Excavator 7PCAT-3E2338

3H-4190 793D Haul Truck Drive Pumps Drain Plug 7PCAT-3H41904B-2363 For: CAT 245 Excavator Sump Final Drive 7PCAT-23634D-7678 CAT 16H, G, M - Motor Grader Chain Case Inspection Plate 1PCAT-4D76784T-2069 D10 Pivot Shaft Fill & Drain Plug 7PCAT-20695F-0304 777 Final Drive Fill Plug 7PCAT-3H41905K-7696 Wheel Loader Final Drive & Brake 988,992,836,B35C 7PCAT-76965P-8005 621F Scraper Transmission Housing Plug 7PCAT-80055P-8006 621F Scraper Transmission Housing Plug 7PCAT-80065P-4483 730 Rear Axle 7PCAT-41815P-4484 For: 854 R.T. Dozer Differential, 834 R.T. Dozer Differential, 988, 992 Differentials 7PCAT-4484

5P-8144 D-10 Transmission & Final Drive, D 9L, D-10 Transmission, D-IIR Final Drive, D-IIN Final Drive, 793 Rear Axle Drain, 797 Differential & Final Drive 3RCAT-8334

6B-5262 777 Final Drive/ Planetary, 16-H Grader Chain Case, 789 / 793 Front Wheel Cover, 621 B Final Drive 7PCAT-70316E-5047 For: 140H Grader Tandem Drive Plug -08 IH 7PCAT-50476E-7696 For: 140H Grader Tandem Drive Plug -08 IH 7PCAT-50476V-0439 For: 789 CAT Truck Final Drive, 854-G R.T Dozer Final Drive, 992 Wheel Loader 7PCAT-0439

6V-3298 For: D-8 Transmission & Final Drive, D 9L, D-10 Transmission, D-IIR Final Drive, D-IIN Final Drive, 793 Rear Axle Drain, 797 Differential & Final Drive 3RCAT-8334

6V-3963 For: D6 Final Drive & Differential Drive, 793 Final Drive 3RCAT-39637X-7731 16H Axle GP- Front 7PNPT34IS8B-6599 For: 637 CAT Scraper Transmission Plug 7PCAT-6599

8M-3837 777 Final Drive/ Planetary, 16-H Grader Chain Case, 789C / 793CD Front Wheel Cover, 621 B Final Drive 785C, 988H, G 7PCAT-3837

8M-5576 For: 24-H Grader Differential, 789 CAT Truck Rear Axle Housing, 793 CAT Truck Rear Axle Housing777 CAT Truck Rear Axle Housing, 785 CAT Truck Rear Axle Housing 7PCAT-5576

8M-7160 Magnetic Filter For Transmission (3/4" x 9" w/ Plate (3S3439) ) 25RCAT-7160M-2782D For: Twin Disc Transmission - 345 Final Drive 7PCAT-2782D

9J-7031 For: D-IIR Hydraulic Tank Drain and Engine, D-IIN Hydraulic Tank Drain and Engine, 621F CAT Scraper Final Drive, 24-H Hydraulic Grader, 854-G R.Tire Hydraulic Dozer 7PCAT-7031

9S-4181 For: 854G Rubber Dozer Engine, 5130B Excavator, 789 CAT Haul Truck Transmission, 793 CAT Haul Truck Trans, 330 Excavator Final Drive, 621F CAT Scraper Final Drive Plug, 345 Excavator Final Drive, 375 Excavator,D10 7PCAT-4181

9S-4182 For: D-10R Hydraulics, D-10N Hydraulics, D10T 7PCAT-41829S-4183 For: 854G R.T. Dozer Engine, 5130B Excavator Engine 7PCAT-41839S-4185 D 10 Dozer Final Drive Drain Plug 7PCAT-4185

"Custom" = OEI's Designed Magnetic Filter

OEM / OEI Cross Reference List


13


OEM / OEI Cross Reference List



NumberCAT Continued

9S-4205 For 621E CAT Scraper 7PCAT-4205

9S-4208 854G Rubber Dozer Engine, 5130B Excavator, 789 CAT Haul Truck Transmission, 793 CAT Haul Truck Transmis-sion, 330 Excavator Final Drive, 621F CAT Scraper Final Drive Plug, 345 Excavator Final Drive, 375 Excavator 7PCAT-4181

9S-8004 For: 24-H Motor Grader - Tandem Housing 7PCAT-8004

9S-8005 279C Track Motor GP-Piston 7PCAT-5047

9S-8006 For. CAT 5110 Excavator Sump Final Drive/16H Front GP- Hub Fill 7PCAT-9S8006

9X-6451 For: C-15 CAT Engine Pan Plug 7PC15EEH

106-8187 D10 Transmission Drain Plug 7PCAT-8187

126-8921 Final Drive Magnetic Drain Plug for 797B & 797F 7PCAT-9S8008

175-6689 For: 24-H Grader Differential, 789 CAT Truck Rear Axle Housing, 793 CAT Truck Rear Axle Housing777 CAT Truck Rear Axle Housing, 785 CAT Truck Rear Axle Housing 7PCAT-5576

264-1176 CAT 16H, G, M - Motor Grader Chain Case Inspection Plate 1PCAT-4D7678

295-5897 For: 3516-B Engine Magnetic Filter for Engine Sump Filter (295-5897) 3/4" x 6" w/ 3/8" NC and 2.875 x 3/8" Support Tee 25RCAT-1W1564

304-8032 For: M12 Tandem Drain Plug 7PCAT-8032Custom Plate # 3S-3439 - 8M- 7160 Magnetic Filter Transmission 25RCAT-7160Custom Plate # 8P3251 - 8M-7160 Magnetic Filter Transmission (O-Ring Plate) 25RCAT-3251Custom Plate # 9P5925 - Transmission Magnetic Filter D11R, 994D 3/4"D x 11.5"L Magnetic Filter Includes Plate 25RCAT-9S5925Custom Engine Sump # 1W-1564 Screen - Magnetic Filter 3/4" x 6" with 3/8" NC and Tee Support 25RCAT-1W1564Custom Engine Sump # 364-8521 For C175 Engine 25RC12C412Custom CAT 16-H, G, M Grader Chain Case Magnetic Filter "Includes stainless steel half coupler for 2" NPT Plug" 3R20HD78Custom CAT 24-H, G, M Grader Chain Case Magnetic Filter "Includes stainless steel half coupler for 2" NPT Plug" 3R24HD78

Custom CAT 16-H, G, M Grader Chain Case Magnetic Filter "Includes modified inspection for Magnetic Filter" 4D-7678, 246-1176 3R20HD78PL

Custom CAT 24-H, G, M Grader Chain Case Magnetic Filter "Includes modified inspection for Magnetic Filter" 120-6152, 120-6156 3R24HD78PL

Custom CAT D-8,D-9,D-10,D-11 Hydraulic Reservoir Magnetic Filter w/ Cam-Lock Mount 3RCL18HDCummins

32822 QSB 6.7 Magnetic Plug 7PM2215ESBS P & H Custom P&H 2800 Shovel Crowd Case "Includes stainless steel half coupler for 2" NPT external hex head" 3R18HD78Custom P&H 2300 Propel Gear Box Upper Location " Cam Lock Mount 24" Total Length, 20 " Magnetic Filter 3RCL24HDCU4Custom P&H 2300 Propel Gear Box Lower Location " Cam Lock Mount 28" Total Length 12" Magnetic Filter 3RCL28HDCU16Custom P&H Hoist Lube System (Install Scrubber Prior to Pump) 5SC12SCLCustom P&H Swing Lube System (Install Scrubber Prior to Pump) 5SC12SCL KOMATSU Custom KOMATSU 830E Hydraulic Tank Cap # TP 0623 with 24" Magnetic Filter 3RORB3224IHCustom 787 Wheel Drive Filler Cap with (Sample Port / Dip Stick and Magnetic Filter.) (GE#41B538253P1) 2RFCS787Custom 787 Wheel Drive Filler Cap with (1/4 or 5/16" Sample Port Dip Stick and Magnetic Filter.) 2RFCS787-2Custom 787 Wheel Drive Filler Cap with (1/2" Sample Port Dip Stick and Magnetic Filter.) 2RFCS787-12Custom 787 Wheel Drive Long Filler Cap with (1/2" Sample Port Dip Stick and Magnetic Filter.) 2RFCS787-127Custom 787 Wheel Motor Filler Cap With Magnetic Filter 6" in Length (GE#41B538253P1) 25RFC78707044-12412 830E Plug # 12412 7PM2415EH07044-13620 Komatsu Plug # 31420, #13620 7PM3615EH07044-31420 Komatsu Plug # 31420, #13620 7PM3615EH763795773 Return Tank Magnetic Filter - PC 3000 thru 8000 2KOM-79573GE-0086 Wheel Motor Magnetic Plug (8 Per Wheel) 7PKOM-0086


14



NumberKOMATSU Continued

H6881 830E Front Spindle Plug # H6881 7PNPT1ISR2491 830E Haul Truck - Hydraulic Tank Magnetic Plug & Spindle Hub 7PKOM-2491SF 9435 830E For: Haul Truck Wheel Drive Reservoir Plug 2RNPT1149ESTY8879 930E Front Spindle Plug # 7PKOM-8879VJ 6489 830E Haul Truck Upper Wheel Drive Plug #VJ 6489 7PNPT114ESVM-0315 830E Haul Truck - Hydraulic Tank Magnetic Plug & Front Brake Piping 7PKOM-0315VM-0317 830E Haul Truck - Steering Accumulator & Rear Brake 7PKOM-0317VS 8411 VS 8411 Komatsu Wheel Drive Plug 42mm x 2.0 Magnetic Plug 7PM4220IHWB-1199 930E Haul Truck Spindle Hub 7PKOM-1199Custom Magnetic Filter for PC1250-2000 - 1/2"D x 10"L with 3/8" NC and Tee Support 2RNC3810T3209-60-77532 Hydraulic Element Filter For: PC1250 9ELSS77532x2521N-60-12210 Hydraulic Spin on Filter For: PC1250 9ADV9-9377 LETOURNEAU 200-0002 Letourneau 200-0002 For: 1850 Final Drive 7PLET5262 LIEBHERR 409710601 Liebherr T282 Haul Truck Plug Part # 409710601 7PM3320EH Liebherr 380 For: Ton Wheel Drive Haul Truck 7PORB16IH Reclaimer Plug Long Travel Gear Box 42mm x 2.0 Magnetic Plug 7PM4220IH SISU 98073 For: Final Drive (Western Star Haul Truck), 793/789 7PORBSISU72 SISU Differential (Western Star Haul Truck) 793/789 7PORBSISUH7510336-F Front Wheel Brake Assem. Plug 2RLBR10336F John Deere R26727 John Deere R26727 For: G Series Back Hoe Axle Differential MT-2075, 310-G, 210-LE 2RORB5727

HITACHI5500 Loader Final Drive 7PHITC114

Hyundai Loader HL770-7 7PMM2215IS Ford New Holland 9848947 Rear Differential Drain Plug 7PFD-8947

SandvikLH621 Wheel End Differential 7PSCK-9842

Custom Sizes and Designs are available

OEM/OEI Cross Reference List


4000 Series Magnetic Funnel Scrubber

15


15


OEI Food Grade Magnetic Funnel Scrubbers are designed for maximum protection of sanitary lines and processing equipment from damaging ferrous contaminants. OEI’s patented Magnetic Technology traps particles to sub-micron levels.

• A variety of sanitary connec-tions are available for ease of installation and service.

• Employs powerful magnetic filter rods with full exposure to the product, with mini-mal flow restrictions and maximum contamination exposure.

• Magnetic filter rods are eas-ily removed for inspection and or cleaning.

• Magnetic field strength removes ferrous contami-nation down to sub-micron levels.

• Designed for permanent installations; simply flush clean then remove magnet-ic filter rods and wipe clean.

• Food • Dairy

• Beverage • Pharmaceutical

FG - Food Grade4FS42FGT


OEI Industrial Grade Magnetic Funnel Scrubbers are designed to remove unwanted ferrous metal (iron, steel, nickel and hardened stainless steel) from the processing lines in which products may be transferred and or packaged.

• A variety of connections are available for ease of installation and service.

• Employ powerful magnetic filter rods with full expo-sure to the product, with minimal flow restrictions and maximum contamina-tion exposure.

• Magnetic filter rods are easily removed for inspec-tion and or cleaning.

• Magnetic field strength removes ferrous con-tamination down to sub-microns.

• Designed for permanent installations, just remove magnetic filter rods and wipe clean.

• Food • Plastic Pellets

• Mineral Powders • Glass Powder

IG - Industrial Grade 4FS43IGW

Box 1 Box 2 Box 3 Box 4 Box 5

4FS 4 42 2 FG T V

Box 1

Funnel Scrubber

Box 4 Installation Connection

T Tri-Clamps

W Weldlet

Box 2 Pipe Size

4112 - 1 1/2" (38mm) 44 - 4" (100mm)

42 - 2" (50mm ) 46 - 6" (150mm)

43 - 3" (75mm ) 48 - 8" (200mm)

Box 3 Usage

FG Processed Food

IG Preprocessed Food and Minerals

Box 5 Installation Mount

H Horizontal

V Vertical

4000 Series Magnetic Funnel Scrubbers

16


16


4150 SERIES MAGNETIC FUNNEL SCRUBBERS 4FS4150FG (Process Food Grade) 304/316 S/S 1-1/2" Inlet/Outlet 31-1/2" L x 4" D (Houses 3-3RF334 magnetic rods)3RF334 1" x 4-1/4" S/S Rod w/2" Ferrules Fastener (fits 4FS4150FG)4FSHDSPC2 HD Single Pin Clamp (fastens magnetic rod to scrubber)4FSBG2 Buna Gasket Ring (seals magnetic rod to scrubber)4FS4150IG (Industrial Grade) 304/316 S/S 1-1/2" Inlet/Outlet 19-1/2" L x 3" D (Houses 3-3RCL334 magnetic rods)3RCL334 1" x 3-3/4" S/S Rod w/1-1/2" Cam Lock Fastener (fits 4FS4150IG)4FSCLBG15 Buna Gasket Ring (seals magnetic rod to scrubber)4200 SERIES MAGNETIC FUNNEL SCRUBBERS4FS4200FG (Process Food Grade) 304/316 S/S 2" Inlet/Outlet 27-1/2" L x 4" D (Houses 3-3RF434 magnetic rods)3RF434 1" x 4-1/4" S/S Rod w/2" Ferrules Fastener (fits 4FS4300/4200FG)4FSHDSPC2 HD Single Pin Clamp (fastens magnetic rod to scrubber)4FSBG2 Buna Gasket Ring (seals magnetic rod to scrubber)4FS4200IG (Industrial Grade) 304/316 S/S 2" Inlet/Outlet 19-1/2" L x 4" D (Houses 3-3RCL434 magnetic rods)3RCL434 1" x 4-3/4" S/S Rod w/1-1/2" Cam Lock Fastener (fits 4FS4300/4200IG)4FSCLBG15 Buna Gasket Ring (seals magnetic rod to scrubber)4300 SERIES MAGNETIC FUNNEL SCRUBBERS4FS4300 (Process Food Grade) 304/316 S/S 3" Inlet/Outlet 19" L x 4" D (Houses 3-3RF434 magnetic rods)3RF434 1" x 4-1/4" S/S Rod w/2" Ferrules Fastener (fits 4FS4300/4200FG)4FSHDSPC2 HD Single Pin Clamp (fastens magnetic rod to scrubber)4FSBG2 Buna Gasket Ring (seals magnetic rod to scrubber)4FS4300IG (Industrial Grade) 304/316 S/S 3" Inlet/Outlet 19-1/2" L x 4" D (Houses 3-3RCL434 magnetic rods)3RCL434 1" x 4-3/4" S/S Rod w/1-1/2" Cam Lock Fastener (fits 4FS4300/4200IG)4FSCLBG15 Buna Gasket Ring (seals magnetic rod to scrubber)4400 SERIES MAGNETIC FUNNEL SCRUBBERS4FS4400FG (Process Food Grade) 304/316 S/S 4" Inlet/Outlet 23-1/2" L x 6" D (Houses 3-3RF634 magnetic rods)3RF634 1" x 6-3/4" S/S Rod w/2" Ferrules Fastener (fits 4FS4400FG Funnel Scrubber)4FSHDSPC2 HD Single Pin Clamp (fastens magnetic rod to scrubber)4FSBG2 Buna Gasket Ring (seals magnetic rod to scrubber)4FS4400IG (Industrial grade) 304/316 S/S 4" Inlet/Outlet 23-1/2" L x 6" D (Houses 3-3RCL634 magnetic rods)3RCL634 1" x 6-3/4" S/S Rod w/1-1/2" Cam Lock Fastener (fits 4FS4400IG)4FSCLBG15 Buna Gasket Ring (seals magnetic rod to scrubber)

FS4600FG SERIES MAGNETIC FUNNEL SCRUBBERS4FS4600FG (Process Food Grade) 304/316 S/S 6" Inlet/Outlet 36" L x 8" D (Houses 4-3RF834 magnetic rods)3RF834 1" x 8-3/4" S/S Rod w/2" Ferrules Fastener (fits 4FS4600FG Funnel Scrubber)4FSHDSPC2 HD Single Pin Clamp (fastens magnetic rod to scrubber)4FSBG2 Buna Gasket Ring (seals magnetic rod to scrubber)4FS4600IG (Industrial Grade) 304/316 S/S 6" Inlet/Outlet 36" L x 8" D (Houses 4-3RCL834 magnetic rods)4R3CL834 1" x 8-3/4" S/S Rod w/2" Ferrules Fastener (fits 4FS4600IG Funnel Scrubber)4FSCLBG15 Buna Gasket Ring (seals magnetic rod to scrubber)4800 SERIES MAGNETIC FUNNEL SCRUBBERS4FS4800FG (Process Food Grade) 304/316 S/S 8" Inlet/Outlet 36" L x 10" D (Houses 4-3RF1034 magnetic rods)3RF1034 1" x 10-3/4" S/S Rod w/2" Ferrules Fastener (fits 4FS4800FG Funnel Scrubber)4FSHDSPC2 HD Single Pin Clamp (fastens magnetic rod to scrubber)4FSBG2 Buna Gasket Ring (seals magnetic rod to scrubber)4FS4800IG (Industrial Grade) 304/316 S/S 8" Inlet/Outlet 36" L x 10" D (Houses 4-3RCL1034 magnetic rods)3RCL1034 1" x 10-3/4" S/S Rod w/1-1/2" Cam Lock Fastener (fits 4FS4800IG Funnel Scrubber)4FSCLBG15 Buna Gasket Ring (seals magnetic rod to scrubber)

5000 Series Magnetic Filter Scrubber

17


Scrubber

Inlet/Outlet standard size is 1 1/2" NPT. Other sizes are available upon request, 1/4" to 1 1/2". * When installing

remember to allow clearance for rod removal.

5SC34 Series Scrubbers are designed for inline installation on low flow, light viscosity fluids such as fuel, engine lube, hydraulics and coolant systems, allowing for full exposure to the contamination and easy removal for cleaning. No flow restriction.

Magnetic filter: 3/4” D x 9” LDimension: 5”W x 3”D x 13” HSquare Housing 150psi

5SC34 Series Provides:• Total Filtration• 304/316 Stainless• Mounts horizontal or vertical• No flow restriction• Plumbed with W.O.G. valves

(optional)• Monel Construction (optional)• 300 F Operating Temperature


* Inlet/Outlet standard size is 2 1/2“ NPTOther sizes are available upon request,

3/4" to 2 1/2”. * When installing remember to allow for rod removal clearance

5000 Series Provides:• Total Filtration• 304/316 Stainless• Mounts horizontal or vertical• No flow restriction• Plumbed with W.O.G. valves

(optional)• Monel Construction (optional)• 300 F or 600 F Operating

Temperature

5000 Series Scrubbers are installed prior to pumps, or on return lines for fuel, lube oil, hydraulics, coolants and water systems, allowing full exposure of the contaminants to the magnetic fields. They are easily cleaned and there is no flow restriction

5SC Dimension lbs/Kg12” 6”Wx4”Dx16”H 16304 mm 101x101x406 mm 7.224” 6”Wx4”Dx28”H 28608 mm 101x101x711 mm 12.736” 6”Wx4”Dx40”H 38914 mm 101x101x1016 mm 19.3

5SC2 Dimension lbs/Kg24" 8”Wx6”Dx30”H 57608 mm 150x150x762 mm 25.9

5SC Custom Outlet

Outlet can be located in several pos-itions, standard design is 180 degrees off the inlet

Square Housing 150 psi

5SC ## RORBWLD ##

This unit is designed with offset in/outlet, a (R) round housing, the Magnetic Filter fastener is (ORB) Plug and the In/Outlet is (WLD) Weldlet

Round Housing 500 psi

5SCP12SCLNPT2This unit is designed with a (P) paral-lel in/outlet for easier installation. The ports can also be located near

the top.(5SCPT12SCLNPT2)

Square Housing 150 psi

Standard Offset DesignSquare Housing 150 psi

Offset Ports0 degrees

Offset PortsBottom

5SC012SCLNPT##5SCBTM12SCLNPT##


18


5SCWOC9FLN8Designed for high volume low pressure

fluid filtration

5SCP ## SCLFLN ##This unit is designed for ease of installation, 5SC- (P) Parallel In/Outlet Design with (S) Square Housing, the magnetic filter fastener is (CL) cam-lock and the In/Outlet is (FLN) flange.

5SCPT ## SCLFLN ##This unit is designed for ease of installation, 5SC- (P) Parallel In/Outlet (T) ports are located near the top, (S) Square Housing, (CL) cam-lock fastener for the Magnetic Filter and the In/Outlet is (FLN) flange.

5SCD ## SCLFLN ##This unit is designed for larger piping applications, designed with offset in/outlet, 5SC- (D) Double magnetic filter with (S) Square Housing, the magnetic filter fastener is (CL) cam-lock and the In/Outlet is (FLN) flange.

Model #Body Dimension only

W x D x H

5SC349SCL 3 x 3 x 13

5SC 4 x 4 x H

5SCR 4 “ Diameter x H

5SCD 4 x 6 x H

5SCP 6 x 4 x H

5SCPR 6” Diameter x H

5SCPD 6 x 6 x H

5SCPDI 4 x 8 x H

5SC2 6 x 6 x H

5SC2P 8 x 6 x H

5SC2PR 8” Diameter x H

5SC2PD 8 x 12 x H

Note: H = Magnetic filter length plus 4 inches

Note: Removal clearance is equal to the filter height

5SCDPI ## SCLNPT ##This unit is designed for ease of installation, 5SC- (D) Dual Magnetic Filters, (P) Parallel In/Outlet, (I) Inline, (S) Square Housing, (CL) Cam-lock magnetic filter fasteners, (NPT) In/Outlet Ports. Designed for single pass applications such as fuel, chemical, water, etc.

5000 Series Scrubber

19


19


Box 5: Length of Magnetic Filter Rod

9 9 inch Magnetic Filter Rod 5SC34 Scrubber only

12 12 inch Magnetic Filter Rod



Box 7: Fastener for Magnetic Filter

CL Cam-Lock 150 psi rating

ORB ORB 500 psi rating

Box 2: Magnetic Filter

34 3/4” Diameter Magnetic Filter 3 x 3 x 13H Body size

Blank 1” Diameter 300 F/ 150C

HH High Heat 1” Diameter 600F/300C

2 2” Diameter 300F/ 150C

2HH High Heat 2” Diameter 600F/300C

Box 3: In/Outlet Location

Blank Offset ports 180 Degree off top port

0 Offset ports 0 Degree off top port

90Offset ports 90 Degree off top port (looking down from top)

270Offset ports 270 Degree off top port (looking down from top)

P Parallel Ports BottomPT Parallel Ports TopBTM Bottom Port

Box 6: Housing Design

S Square 150 psi rating

R Round (500 psi w/ ORB Fastener)

Box 9:

Port Size

1/2

3/4

1

1 1/2

2

2 1/2

etc.

Box 10:

Flange ANSI Class

150

300

600

900

1500

Box 1 : Scrubber Model

5SC 5000 Series Large Flow Systems

Box 4: # of Magnetic Filters

Blank Single Magnetic Filter

D Dual Magnetic Filter

DI Dual Inline Magnetic Filter

T Triple Magnetic Filter

Q Quadruple Magnetic Filter

Box 8: Port Options

NPT Nation Pipe Thread Tapered

FLN Flange

WLD Weldlet

BSP British Pipe

M Metric

HOW TO ORDER: Select the desired code (in the correct position) to construct a product.

EXAMPLE:

Box 1: Box 2: Box 3: Box 4: Box 5: Box 6: Box 7: Box 8: Box 9: Box 10:

5SC P D 24 S CL FLN 6 150

See inside back cover for Flow Rates Chart

20




Magnetic Canister Filtration System

OEI's dual filtration system has reinforced cleanable stainless steel cloth media elements combined with our patented magnetic filtration capable of filtering to sub-micron levels.

Designed to replace traditional bag and sock filtration systems.

Designed for filtering water, oil, coolant, cutting oil, fuel and cleaning solutions.

* Custom Replacement elements with magnetic filters for existing bag filters and cartridge filters are available

Features:

• Housing – Carbon or Stainless Steel construction, permanently piped in (up to 6” pipe size)• Elements 304 and 316 stainless steel, include magnetic filter rod• Extend cleaning life up to 3x, easy to clean• Reduce maintenance cost, PM• Eliminates bags, outer baskets, bag hold down assemblies, and bag restrainers• 150 psi (standard)• Carry all sizes – custom sizes are available• Flow rates up to 400 gpm – custom design for other flow rates• High heat applications are available• Long life 10+ years

Box 1 Box 2 Box 3 Box 4 Box 5 Box 6 Box 7

5CF 304 2 FLN BTM 25 V

Box 3

Pipe Size

234 6

Custom

Box 7

Seal

B - BunanE - Ethylene Propylene

V - Viton

TEV - Teflon Encapsulated VitonTSW - Teflon (solid

white)

Box 1

Model Number- Filter Length

5CF-20

5CF-30

Box 4

In/OutletType

FLN - Flange

NPT - Thread

Box 5

In/OutletLocation

Blank - 180 degree

0 - 0 degree90 - 90 degree

270 - 270 degree

BTM - Bottom

Box 6Micron Rating

102540 60

80

100

Box 2

Housing

304

316CS- Carbon

Steel

5000 Series Magnetic Canister Filtration System

Dimensions

5CF-20 5CF-30

A = 6" 6" B = 4" 4" C = 5.5" 5.5" D = 8" 8" E = 33" 52" F = 38" 57" G = 20" 20"

Y-Strainer • Bronze / Brass

21


Y-Strainer • Bronze


OEI Introduces our Magnetic Filter Y-Strainer Series

OEI understands the importance of filtration and the restrictions of space on equipment. OEI saw the need to improve the filtering capabilities of the traditional Y-Strainer by installing our patented Magnetic Filter. If used as a suction strainer OEI suggests removing the filter screen. The Y-Strainer is now capable of trapping ferrous and non-ferrous contaminants by static adhesion and entrainment to the sub-micron range. This is a major improvement to many systems that rely on a Y-Strainer for protection. Visit our web site for more information, and view our case studies.• Chemical • Pneumatic Systems • Steering Systems • Grease Filtration • Brake Systems

• Coolant Systems • Fuel Systems • Hydraulic Systems • Mobile & Static Equipment • Cryogenic Applications

WORKING PRESSURE (NON-SHOCK): 300 PSI @ 350F

Steam Rated 400 PSI @ 150F WOG

SizeIn. mm

1 25mm1 1/2 40mm2 50mm2 1/2 64mm3 75mm4 100mm

A

4 3/4 (12cm)5 3/4 (14.6cm)6 3/4 (17.1cm)8 (20cm)9 1/2 (23.5cm)12 (30.5cm)

B

4 (10cm)5 (12.7cm)6 (15.2cm)6 (15.2cm)7 (17.5cm)10 (25.4cm)

NETWEIGHT

Lbs Kg

3 1.45 2.37 3.212 5.516 7.322 10

DIMENSIONS

Box 1: Box 2: Box 3: Box 4: Box 5: Box 6:

5Y B 112 T A

Box 3

Pipe Size

1 1 1/2

2 2 1/2

3 4

Box 5Flange ANSI

Class Bronze leave

Blank

1 - 150

3 - 300

6 - 600

9 - 900

15 - 1500

Box 1

5Y- Magnetic Y-Strainer

Box 4

Port Type

T - Threaded

F - FlangeBox 2

B - BronzeS - Stainless Steel

BC- CryogenicsHP- High Pressure

Box 6

Mesh

X - No Mesh Screen

A - 20

C - 40

D - 60

E - 100 NOTE:

BC- Y-strainer available in 2", 2 1/2", 3"

OEI is pleased to offer our custom designedMagnetic Filter Y-Strainer for cryogenic applications. Our flanged access allows access for cleaning at -320 degrees F. The magnetic filter removes both ferrous and non-ferrous contamination to sub-micron levels extending the life of linings and pump components.

This high pressure Y-Strainer is designed for system pressures of up to 6000 PSI. It's increased filtration capability removes both ferrous and non-ferrous contamination, including that due to pump damage, down to sub-micron levels without flow restriction effectively reducing the energy demands of traditional filtration. The magnetic filter has a life expectancy of 10+ years with minimal consumables.

N E W!

Y-Strainer • Stainless Steel

22


22


OEI’s Stainless Steel Magnetic Filter Y-Strainer Series

TempF

-20 to 100200300400500

150#Size A B WT

1” 6 3/8 5 111 1/2 7 3/4 5 1/4 172” 7 7/8 6 233” 10 7 1/2 424” 12 1/8 11 73

Working Pressure

275240215195170

150#, 300#, 600# ANSI 316SS - Raised Face Flange

5YS112F3

150# 300# 600#

Working Pressure

720620560515480

300#Size A B WT

2” 8 5/8 6 1/4 283” 12 8 1/4 564” 14 1/2 11 98

600#Size A B WT 1” 8 3/8 5 161 1/2 9 7/8 6 242” 11 1/8 6 3/4 473” 13 3/8 9 1/2 89

Working Pressure

1440124011201030955

• Body has machine seat to hold screen securely.

• Cover has a machined screen holder to align screen during installation and to retain sediment when cap is removed.

• Body is machined to hold gasket in a blow-out proof design.

• Flanges are back faced or spot faced.

TempF

-20 to 100200300400500

Size A B WT

2” 13 3/4 8 5/8 96

Working Pressure

360030952795256023905YS2F15

Description Material

Body ASTM A- 351 GR CF8MCap ASTM A- 351 GR CF8MGasket Spiral Wound SSScreen 304 SS Specify Mesh

1500# ANSI 316 SS - Raised Face / RJT Flange

5YS2T6

• Body has machine seat to hold screen securely.

• Cap has a machined screen holder to align screen during installation and to retain sediment when cap is removed.

• Body is machined to hold gasket in a blow-out proof design

TempF

-20 to 100200300400500

600#Size A B WT

1” 4 9/16 3 1/2 52” 7 1/2 6 1/2 16

WorkingPressure

1440124011201030965

600# 1500#

Working Pressure

36003095279525602390

1500#Size A B WT

1” 5 1/2 4 3/4 8

1 1/2 7 1/8 6 16

2” 8 5/16 6 5/8 22

600# / 1500# ANSI - 316SS - NPT Thread

7000 Series Plugs

23


OEI manufactures plugs with High Energy Magnetics, designed to replace the OEM industries standard ceramic magnetic plugs for final drives, rear ends, transfer cases and transmissions.

* 300F Operating Temperature (600F optional)

Box 4Inches

NPT, BSP1/8”1/4”3/8”1/2”3/4”1”

1 1/4”1 1/2”

2”2 1/2"

Box 1 Box 2 Box 3 Box 4 Box 5 Box 6

7P M 16 15 EH

Box 1 Magnetic Plug7P Plug

Box 2 TemperatureBlank 300F / 150CHH 600F / 300C

Box 3 FastenerNPT Nation Pipe Thread

BSPP British Standard Pipe Parallel

BSPT British Standard Pipe Tapered

M Metric ThreadORB O-Ring Boss

How to Order ...

* Custom Sizes and Designs are available

Plug Sizes & Types

Metric Sizes ORB Sizes

10mm -0412mm -0514mm -0616mm -0818mm -1020mm -1222mm -1426mm -1627mm -2030mm -2433mm -32

36mm etc.

Box 5 Metric Thread

1.01.251.52.0

Box 6 Fastener ToolIS Internal SquareES External SquareIH Internal HexEH External Hex

ESD External Square Drilled

Seal Types for ORB (SAE), BSPP, and Metric Plugs:

Standard O-Ring Recessed O-Ring Bonded Seal

Box 7 Seal TypeBlank Standard O-Ring

RO Recessed O-Ring

BS Bonded Seal (Hard Washer)

24




8000 Series Thermal Filtration System

N E W !DUAL PURPOSE THERMAL KIDNEY LOOP

Combining OEI sub-micron filtration capability and a thermal cooling system offers the ability to maintain a safe operational temperature and an ISO cleanliness level that will extend the lube oil and component life.

For application on gear boxes, hydraulic and coolant systems. Equipped with temperature gauges and sample ports before entering the unit and after to identify the reduction in temperature and contamina-tion in the fluid or oil.

Compact and available in custom designs for all applications to suit individual requirements. For mobile and static employment and powered by DC, AC and Hydraulic drive.

Our Thermal Kidney Loop system is designed with a magnetic filter in our Scrubber format prior to the pump to remove the ferrous metals to sub-micron levels and protect the pump and the thermal compo-nents and an ADD-Vantage 9000 filter to remove any residual non-ferrous contamination before returning the fluid and or oil to the application.

To ensure the most efficient and effective Thermal Kidney Loop for your application please identify the following:

• Static or Mobile Oil Temperature Ambient Air Temperature• Power Source AC/ DC Viscosity Required Heat Rejection (KW)• Voltage / Phase Reservoir Size ( gallons) Air Flow (Suction or Push)


25


THE NEXT GENERATION KIDNEY LOOP FILTRATION SYSTEMSENVIRONMENTALLY FRIENDLY AND HIGHLY EFFICIENT


The OEI Kidney Loop combines two filtration technologies in a three filtering stage design that offers a highly efficient and environmentally friendly cleanable long life filtration system.

1st Filtering Stage and primary filter is a magnetic scrubber utilizing OEI patented technology rated to sub-micron filtration capability.

2nd and 3rd Filtering Stage is the ADD-Vantage 9000 series dual filter. The 2nd Filtering Stage is a cleanable long life stainless steel cloth media element that has an absolute rating of 25 or 40 microns and a nominal rat-ing of 8 to 10 microns. The stainless steel cloth media element eliminates the worm holing and channeling that occurs in cloth, paper, fiberglass, or polymer media. The 3rd and final Filtering Stage is a magnetic filter inside the Add-Vantage 9000 stainless steel element to trap contamination to sub-micron levels.

System Features

• Positive Displacement Gear Pump• 5 - 10 gpm• Viscosity 500 or 1000 cSt• OEI 5000 Series Magnetic Scrubber• Removable Oil Spill / Drip Tray• On/Off Switch• Electrical System – International Requirements • 16”W x 20”D x 30”H

Options• Disposable Elements• Water Absorbent Filter• OEI Series Scrubber 24” Height• ADD-Vantage 9000 Dual Filter 12” or 24” (reusable filter element and magnetic filter)• Differential Pressure Gauge• Pneumatic Pump• Sample Port• Mobile (Wheels)• Fluid Flow Gauge • Flow Switch• Particle Counter• Isolation Ball Valve• Customer Preferred Pump or Motor (brand)• Quick Connection Fittings

* Custom orders are available.8KLF-51-91-40-500-E-230-60-1-NPT-2

Gear Boxes - Hydraulics - Lube Oil Water - Chemicals - Glycol - Transformer Fluids

8000 Series Kidney Loop System

26


Box 1 Box 2 Box 3 Box 4 Box 5 Box 6 Box 7 Box 8 Box 9 Box 10

8KLF 51 91 25 1000 E 240-50-3 NPT 2

Box 3 ADD-Vantage 9000

Blank No Filter Mount91 12" Tall Filter92 24" Tall Filter

Box 7 Voltage - Hertz - Phase

List

Box 1 Model Number

8KLF Kidney Filtration Stationary

8KLM Kidney Filtration Mobile

Box 4 Filter Micron RatingBlank No Filterx 100 100 Micron B200

x40 40 Micron B200 x25 25 Micron B200

x1 1 Micron B200

WA Water Absorbent Filter

DP Disposable Element

Box 5 Oil Viscosity

500 Up to 500 cSt

1000 500 to 1000 cSt

Box 6 Pump

E Electric

P Pneumatic

Box 2 Scrubber Model

51 12" Tall Scrubber

52 24" Tall Scrubber

Box 8 Pluming Connection

NPT National Pipe Thread

BSP British Standard PipeQ Quick Coupler

Box 9 Connection Size

List Size 1/2, 3/4, 1, 1 1/2, 2 "

Box 10 Options

DPG Differential Pressure Gauge

FFG Fluid Flow GaugeFS Flow SwitchPC Particle Counter

SPM Specify Pump & Motor Brand

SP Sample PortBV Isolation Ball Valve

* Replacement Parts

9EL5040001 x25 or x40 - Replacement Element 25 or 40 Micron for 91 filter9EL5040401 x25 or x40 - Replacement Element 25 or 40 Micron for 92 filter9OR348 - End Cap O-Ring for both filters9OR351sq - Filter Mount Gasket for both filters9BPA5050001 - ByPass and Magnetic Filter for 91 Filter9BPA5050401- ByPass and Magnetic Filter for 92 Filter9ELWA5040001 - Water Absorbing filter for 91 filter 9ELWA5040401 - Water Absorbing filter for 92 filter

8KLF-51-1000-E-230-60-1-NPT-2

8000 Series Kidney Loop System

8KLF-52-1000-E-230-60-1-NPT-2 8KLF-52-92-25-1000-E-230-60-1-NPT-2

Sample Port (8KLFSP)Fluid Flow Gauge (8KLFFFG)Flow Switch (8KLFFS)Particle Counter (8KLFPC)Differential Pressure Gauge (8KLFDPG)


27


The 1st stage and primary filter is a Magnetic Scrubber utilizing OEI patented tech-nology rated to sub-micron filtration capability.

- Manufactured with high quality stainless steel - Design allows for full exposure of ferrous contamination to the magnetic filter rod resulting in filtration of ferrous particles down to sub-micron levels and no internal flow restriction and is designed to protect the pump

2nd stage is the ADD-Vantage 9000 series filter. This is a dual filter with a stainless steel element to remove large contaminants with an absolute rating of 25 to 40 microns and a nominal rating of 8 to 10 microns.

-The stainless steel cloth media element also eliminates worm holing and channeling that occurs in cloth, paper, fiberglass or polymer media

3rd stage is a final magnetic filter inside the ADD-Vantage 9000 stainless steel ele-ment to trap ferrous contamination to sub-micron levels.

System Features: Positive Displacement Gear Pump, 5 to 10 GPM, Viscosity 500cSt, OEI 5000 Series Magnetic Scrubber, 9000 Series ADD-Vantage Magnetic Filter, On/Off Switch, Oil/Spill/Drip Tray, Electrical System- International Requirements

*Custom units are available

Mobile Filter Cart 8KLD5191

The OEI Mobile Filter Cart combines two filtration technologies in a three-stage design that offers a highly efficient and environmentally friendly, cleanable, long life filtration system.

N E W !

The High Flow Magnetic Filtration Systems are designed for Hydro Carbon Fluids, Chemical and Water.

This system is designed to be installed inline Custom designs and sizes are welcome!• 2” to 8” Inlet / Outlets: Flange, Threaded or Weldlet• 5SC2P - 2” x 24” (50mm x 600mm) Magnetic Filter• High Strength Magnetic Patented Technology rated at 300°F - 150°C (600°F - 300°C)• Cam Lock for easy cleaning• 2 - ADD-Vantage 9000 Filters mounted in parallel, construction with Stainless Steel elements 100%

Reusable

HOW TO ORDER...

8HF2PD - 94 - FLN - 3 - 24

Scrubber

8HF2P - Single 2” MF8HF2PD - Double 2” MF

Number of Filters

92 - 2 Filters94 - 4 Filters

In/Outlet Type Size HeightFLN - Flange 2 to 8 in 24" 60cmNPT - Pipe Thread 50 to 200mmWLD- WeldletBSP- British Thread

* Quote per order

8000 Series Filtration Systems


ADD-Vantage 9000 Series

28


ADD-Vantage 9000 Series is the combination of two filtration technologies: • Reusable, stainless steel element• Patented magnetic filter technologyThe 9000 offers the most advanced filtration on the market today; a reusable, easily cleaned, long life element.• Replaces disposable filters, eliminates environmental taxes

and used filter disposal costs• Installs just like a disposable filter, no retrofitting is required.

Removal and inspection are easy with a built-in Femco® compatible drain plug.

• No other filter on the market can provide the significant savings 2 year payback, 10+ year effective life – and unsurpassed filtering of the ADD-Vantage 9000 Primary Filter

Traps ferrous& non-ferrouscontamination

down tosubmicron levels

which areanalyzed fora predictivemaintenance

program.

The most advanced filtration technology for fluids and oils in the world.

Primary Oil, Fuel & Hydraulic FiltersThe most advanced filtration technology for fluids and oils in the world.

ApplicationsPrimary oil & fuel filter applications • Designed for heavy duty diesel trucks and large capacity die-

sel engine installations in all industries• Extend oil change intervals from 300 to 1000+ hours with oil

analysis• Removes ferrous and non-ferrous contaminants to sub-micron

levels reducing wear cycle on bearings, seals, heads and pis-tons

• Reduces the scoring of fuel injectors increasing fuel economyHydraulics – primary & secondary filtration and suction & return line installations• Removes contaminants that prematurely wear pumps and

seals• Maintains high ISO cleanliness levels, extending fluid life • Reduces corrosion• Amine & glycol • Compressor lube oil • Turbines

Benefits • Continuous total filtration of the most damaging contami-

nants (iron and steel) down to 1 micron.• Flows 40% more fluid than conventional elements• True filtration, no “channeling” or “worm holing”.• Filter elements easily clean in a parts washer or an ultrasonic

cleaner, with solvent, or soap & water or the OEI Enviro Wash Station (see page 34).

• Also fits conventional paper and glass pack filters • Allows inspection of wear metals trapped on the magnetic

filter rod and filter• Eliminates costs of filter stocking and used filter disposal• Eliminates environmental impact from disposal of used filters

& oil and associated environmental taxes• 3 year full warranty, 10+ year effective life• Extend oil change intervals from 300 to 1000+ hours with oil

analysis

Specifications• High flow rate inlet, outlet & filter. Patented bypass and magnetic filter rod.• 10, 25 & 40 micron, absolute rated, filter elements filter down

to 5-7 microns before activating the bypass• Exceeds industry standards for filtration (ISO 4572), bypass

limitations, and collapse pressure (ISO 2941)• 316 stainless steel magnetic filter – continuously filters fer-

rous and non-ferrous contaminants (due to adhesion) to sub-micron levels• Industrial steel machined housing• Femco© drain compatible • Remote mounts, spare parts, o-rings and filter elements are

all available• OEI's Stainless elements with integrated magnetic filter rod,

available for CAT, Waukesha, Cummins and most other brands

We carry a complete stock of replacement O-rings, filter elements, anti-drain back valves, bypass valves and components to repair dam-aged filters.

Check our web site www.OneEyeIndustries.com or contact us directly for more details.

Replacement O-rings, Filter Element & Repair Components

Improves Environmental Footprints

28

29


ADD-Vantage 9000 SeriesHigh Flow Dual Filtration System

The “High Flow Dual Filtration System” is a combination of two filtration technologies.1) Beta 200 rated reusable stainless steel element 2) OEIs’ patented magnetic filter extracts and traps ferrous and non-ferrous

contamination.The ability to remove non-ferrous contamination is through ferrous to non-ferrous abrasive contact and static adhesion.Employed on a custom OEI high flow filter mount base that allows up to 200 gallons a minute of flow. This filter is recommended for fuel and light viscous oils.Available in single and duplex configurations.

9ADV9 - 266FF - NPT# - B

Dimensions W x D x H Weight - lbs

9ADV9 5 x 5 x 24 22Base 6 x 6 x 5.50 12Inline 5 x 5 x 5.50 7

# Inch In/Outlets

NPT - National PipeBSP - British PipeFLN - FlangeWLD - Weldlet

Mount

B - Base MountI - Inline

5.0"

Length

New Lube Oil and Fluid Dispenser Filtration

How to Order...9ADV9 – 700 - # - #

Designed for filtering new fluids prior to dispensing in the following applications: Lube Oil – Hydraulic – Coolant – Fuel - etc. The ADD-Vantage 700 series is designed with two filtration systems in one, 1st a stainless steel element providing maximum filtration protection, eliminating any chance of “worm holing or channelling” the element is reusable and available in 40, 25 or 10 micron β200 rating. The 2nd is our patented magnetic filter designed to create multiple independent radial magnetic fields filtering contaminants to sub-micron levels.

The ADD-Vantage 700 is rated up to 700 psi and designed with 2” NPT in/outlets and available in a 15” or 27” long unit.

Model Box 1 Box 2

9ADV9-700 27 25

Box 1 Filter Body Length15 15” - Long Body 400 Sq inch media

27 27” - Long Body 850 sq inch media

Box 2 Filter Micron Rating40 40 Micron Filtration B200

25 25 Micron Filtration B200

10 10 Micron Filtration B200

30





ADD-Vantage 9000 Wrench

The ADD-Vantage 9000 Series bodies were designed to be held by an adjustable Pin Spanner Wrench while removing or installing the Element Cap.This tool is available at most tool supply companies.Description: Adjustable Pin Spanner WrenchMax Capacity: 6-1/4 "Diameter: 3/8"Pin Length: 1/4"Hook Size: 15.32"Length: 12-1/8"Part # 1APSW

OEI Duplex Filtration System. Designed with OEI’s reusable dual filtration units the stainless steel elements can be removed for cleaning and the magnetic filter inspected for wear contaminants while your equipment continues to work.

This duplex system is very versatile with multiple port op-tion from ¾” NPTF to 2” NPTF or SAE 12 to SAE24.

BOX 1Body Length

BOX 2Connection

BOX 3Micron Rating

D9L – 12“ BodyD9XL – 24” Body

PB – 3/4” NPTFPC – 1” NPTFPD – 1 1/4” NPTFPE – 1 1/2” NPTFPF – 2” NPTFPM – 12 SAEPN – 16 SAEPO – 20 SAEPP – 24 SAEPX – Blank Flange

X 25X 40 X 80

X 100

Duplex System W x D x H

9ADV9-D9L 12 ½” x 25” x 18” 32mm x 64mm x 46mm

9ADV9-D9XL 12 ½” x 25” x 30” 32mm x 64mm x 76mm

9ADV9 - D9XL - PX - x259ADV9 - D9L - PX - x25

To Order...9ADV9- BOX1- BOX2- BOX3


31


31


A 100% Reusable Filtration System designed for the machining/milling industry. This ADD-Vantage 9000 (Milling) replaces all conventional disposable filters. Designed with a dual filtration system: Stainless Steel Element with 1/16” perf. screen to trap large particles and OEI’s Patented Magnetic Filter will trap ferrous contaminants to sub-micron levels. Extending the life of your coolant/cutting fluids and equipment. This filter is easily cleaned and has an effective life of 10+ years. A remote mount base is available in 1" and 1-1/2" inlet/outlet. Continuously filters ferrous contaminants to sub-micron levels.

9ADV9 - M - 24

Filter System M - MillingG - Grease

Length1224

Grease Filtration System

Designed to filter grease before it reaches your bearings. The ADD-Vantage 9000 (Grease) filter is equipped with OEI’s Patented Magnetic Filter, trapping ferrous contaminants to sub-micron levels, extending the life of your seals and bearings. This filter is easily cleaned and has an effective life of 10+ years. Sold with a remote base mount, available with a 1" or 1-1/2" inlet/outlet.This system can be installed remotely on automatic greasing systems such as ATS Electro-Lube, Lincoln, Farval, etc.For smaller application, install OEI’s Magnetic Y-Strainer.

OEI has modified its Y-Strainers for smaller inline application for filtering grease. Equipped with OEI's patented Magnetic Filter, this system will trap ferrous contaminants extending the life of your seals and bearings.5YB1TXG - 1” inlet/outlet5YB112TXG - 1½” inlet/outlet

9RMHY5Remote Mount - Hydraulic 1 1/2" In/Outlet Other sizes available

9ADV9 - G - 12

Dual Milling Filtration System

32




THE ENVIRO-WASH 9000

OEI introduces an environmentally friendly and cost effective cleaning system for stainless steel cloth media filter elements. The Enviro-Wash 9000 cleaning system is compact, mobile, user friendly and replaces the tra-ditional ultrasonic cleaning systems.

OEI’s biodegradable cleaning solution will remove carbon, soot, graphite, oils, tars, solvent based products, water repellent greases, waxes, grease, soils and protein deposits.

The Enviro-Wash 9WSH-8 system is designed to clean all our stainless steel cloth media elements. The system operates as a soak and spray process that cycles in 30 minutes from dirty to clean elements and allows the cleaning of (2) 24” elements, (4) 12” elements or (8) 6” elements. The 20 litre envirowash cleaning solution will have a cleaning capacity of 900+ filter elements on average.

The Enviro-Wash 9PWSH-### system is designed as an individual system to clean all our stainless steel cloth media elements. The system operates as a soak and spray and air dry process.

Envirowash 9WSH-8 includes• Mobile wash station 33”W x 25”D x 40”H• 4 - 20 litre pails of envirowash • 6 - Absorbent filter pads• (12) - Element storage bags for 12” elements• (12) - Element storage bags for 24” elements

Envirowash 9000 Consumables • Envirowash solution – available in 20 litre pails• Absorbent filter pads• Element storage bags

We carry all replacement parts for the Envirowash 9000.

9WSH-8

9PWSH-318-elements 1” – 2.8” dia. up to 9” long, 1 Litre of cleaning solution required.

9PWSH-418-elements with a 2.8” – 3.8” dia. up to 9” long, 2 Litre of cleaning solution required.

9PWSH-436-elements with a 2.8” – 3.8” dia. up to 18” long, 4 Litre of cleaning solution required.

9PWSH-620-elements with a 3.8 – 5.8” dia. up to 10” long, 4 Litre of cleaning solution required.

9PWSH-648-elements with a 3.8” – 5.8” ”dia. up to 24” long, 8 Litre of cleaning solution required

9PWSH-###

9WSH-8 9PWSH-###



33


33


The filters below are in production, please identify other filters required. Screens are available in 10, 25 & 40 microns. Please specify. Filters for other applications and equipment manufacturers are available on order request (John Deere, Volvo).

ADD-VANTAGE 9000 REUSABLE FILTERS – FOR APPLICATION ON OIL FUEL HYDRAULIC COOLANT SYSTEMS – Cleanable 316 Stainless Steel Element & Magnetic Filter & Internal Bypass – All machined steel Construction. Custom orders for most disposable filter sizes 3.625” OD FILTER DIMENSIONS

Engine Adapters

9ADV9-1000 Primary Fuel Filter for most CAT/ Cummins / Detroit / Mac/ Volvo / Mercedes

9EA3010401 Engine Adapter 1” x 14 UN (BF 957)9SCG20 Gasket 2.47” ID x 2.85” OD 9ADV9-B260 Engine Lube, Compressor Lube and Hydraulic Applications9EA3010202 Engine Adapter 11/8” x 16 UN9SCG20 Gasket 2.412” ID x 2.812” OD 9ADV9-B262 Engine Lube, Compressor Lube and Hydraulic Applications9EA3010201 Engine Adapter 1” x 12 UN9SCG20 Gasket 2.412” ID x 2.812” OD 9ADV9-PH3976A Engine Lube, Compressor Lube and Hydraulic Applications9EA3010101 Engine Adapter 1” x 16 UN9SCG20 Gasket 2.47” x 2.85”9ADV9-B237 Engine Lube, Compressor Lube and Hydraulic Applications9EA3010301 Engine Adapter 3/4" x 16 UN9SCG20 Gasket 2.455” ID x 2.835” OD 3.625” COMMON FILTER COMPONENTS9B3020201 Canister Body 3.625: x 7.5L9EC3030001 Filter End Cap9BPA3050201 Bypass & Magnetic Filter 73mm x 1Bar/w 25RNC5165259BPS3060001 Bypass Coil Spring9OR218 Filter Element O-Ring9OR236 End Cap O-Ring9DP263750 Drain Plug 3/4" x 16 SAE9CG263860 Drain Plug Gasket 3/4"9EL3040201 S/S Filter Element4.25” OD FILTER DIMENSIONSEngine Adapters9ADV9-PH49A CAT/ Volvo/ Mack:

CAT 1R0658, 1R0714, 1R0739 1R1807, 2P4004, 2Y8096

9EA4010301 Engine Adapter 1 1/8” x 16 UN

9SCG9 Gasket 3.59” ID x 4.01” OD

9ADV9-B7155 Hitachi Excavators, Kobelco Wheel Loader


Gasket 3.875” ID x 4.315 OD

9ADV9-PH3786 Ford / IHC Trucks w/ 7.3 Turbo Diesel (94-03)


Gasket 3.692 x 4.0112”

9ADV9-0958 K2000 Fuel Primary

9EA5010203 Engine Adapter 1 1/8" x 12 UN

9SCG18 Gasket 3.85" ID x 4.35 OD

9ADV9-0959 K2000 Fuel Secondary


4.25” COMMON FILTER COMPONENTS9B4020001 Canister Body 4.25” OD x 9.90L

9EC4030001 Filter End Cap

9BPA4050001 Bypass & Magnetic Filter 94.5mm x 1Bar/w 25RNC5166

9BPS4060001 Bypass Coil Spring

9OR226 Filter Element O-Ring

9OR242 End Cap O-Ring

9DP263750 Drain Plug 3/4" x 16 SAE

9CG263860 Drain Plug Gasket 3/4"

9EL4040101 S/S Filter Element

5.0” OD FILTER DIMENSIONSEngine Adapters9ADV9-0755 CAT 1R-07559EA5010202 Engine Adapter 1 3/8” x 16 UN 9SCG18 Gasket 3.85” ID x 4.35” OD

9ADV9-4005 CAT C15,C12, C10, C16, 3406, 3408

9EA5010201 Engine Adapter 1 1/2 x 16 UN


9ADV9-3566 CAT 1R1808


9SCG18 Gasket 3.845” ID x 4.35 OD

9ADV9-3612 Cummins K2000, Detroit Diesel


9SCG10 Gasket 3.64 ID x 4.31” OD

9ADV9-3671 Detroit Diesel 50,60 Series LF3671


9SCG18 Gasket 3.845” ID x 4.35 OD

9ADV9-0495 Detroit Diesel 50, 60 Series Power Guard B495


9SGC10 Gasket 3.64” ID x 4.31” OD

9ADV9-3555 CAT, Cummins, Volvo, IHC, John Deere, P3555A



9ADV9-7138 IHC, Detroit Series 40

9EA5010006 Engine Adapter 36mm x 1.5


9ADV9-3000 N14 Cummins



9ADV9-9001 Cummins ISX, ISB, ISC, ISM



9ADV9-9024 Cummins QSK60


Gasket 4.0” x 4.68” OD

5.0”OD COMMON FILTER COMPONENTS

9B5020101 Canister Body N14

9B5020001 Canister Body 5” OD x 12 5/8” L


9EL5040001 S/S Filter Element for 12 5/8” Body & N14

9EL5040002 S/S Filter Element for 9 7/8” Body

9BPA5050001 Bypass & Magnetic Filter (25RNC387) 12 5/8 Body

9BPA5050002 Bypass & Magnetic Filter (25RNC3845) 9 7/8 Body





9CG263860 Drain Plug Gasket 3/4"

9EL4040001 S/S Filter Element


33

Industrial Filtration Solutions

34


34

ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on PadsISO 9000 • To order any other parts not listed above, please contact us.

ADD-VANTAGE 9000 HYDRAULIC FILTER

9ADV9-926170 Short Version


9EL5040002 S/S Filter Element 25 Micron 4.17 OD x 2.83” ID x 7.00” L

9BPA5050002 Bypass & Magnetic Filter 1 Bar – 25RNC384.75

9ADV9-926170L Standard


9EL5040001 S/S Filter Element 25 Micron 4.17” OD x 2.83” ID x 9.73” L

9BPA5050001 Bypass & Magnetic Filter 1 Bar – 25RNC387

9ADV9-926170LX2 Long Version

9B5020401 Canister Body 5” OD x 24” L

9EL5040401-B S/S Filter Element 25/40 Micron 4” OD x 2.83” ID x 21.6” L


9ADV9-266-FF High Flow Filter

9EA61010 Mount Adapter w/2” Flange

9B5020401 Canister Body 5” OD x 24” L

9EL5040401-B S/S Filter Element 25/40 Micron 4” OD x 2.83” ID x 21.6” L


Common Filter Components

9EA5010008 Mount Adapter 1 1/2" x 16 UN






9CG263860 Copper Gasket 3/4”

ADD-VANTAGE 9000 MILLING FILTER

9ADV9-M-12

9B5020001 Canister Body 12 5/8”

9EL5040003 S/S Filter 1/8” Perf. 4.17 OD x 2.83 ID x 9.7 L


9ADV9-M-24

9B5020401 Canister Body 24”

9EL5040004 S/S Filter 1/8” Perf. 4.17 OD x 2.83 ID x 19.5 L


Common Filter Components

9EA5010008 Mount Adapter 1 1/2" x 16 UN






9CG263860 Copper Gasket 3/4”

ADD-VANTAGE 9000 GREASE FILTER

9ADV9-G-12

9EA5003901 Mount Adapter 1 1/2” x 16 UN w/ Solid Element


9EC50300003 End Cap w/ 3R8 Magnetic Filter


9000 SERIES REMOTE FILTER BASE MOUNT

9RM3000 Base Mount for 9ADV9-3000 N-19

9RM3612 Base Mount for 9ADV9-3612

9RMHY5 Base Mount for 9ADV9-926170L

9RM266 Base Mount for High Filtration System

STAINLESS STEEL REPLACEMENT ELEMENTS – Lube and Hydraulic Applications Custom element sizes are available. – All OEI elements come with magnetic filters – Replace OEM Disposable Elements with OEI Stainless Steel Elements.

9ELSS9600825 Stainless Element 25 Micron Absolute/10 micron Nominal 8" L








STAINLESS STEEL SUCTION STRAINERS – Stainless Steel Suction Strainers w/magnetic filter

9ELSSSSNPT38 S/S Suction Strainer 3/8" NPT 1.80" OD X 3.50" L



9ELSSSSNPT100 S/S Suction Strainer 1" NPT 2.60" OD X 5.50" L

9ELSSSSNPT114 S/S Suction Strainer 1-1/4" NPT 3.40" OD X 7.70" L

9ELSSSSNPT112 S/S Suction Strainer 1-1/2" NPT 3.40" OD X 8.90 "L


9ELSSSSNPT212 S/S Suction Strainer 2-1/2" NPT 5.90" OD X 8.40" L


34

ADD-VANTAGE 9000 DISPOSABLE CELLULOSE ELEMENTS

9ELDP3040201 Filter Element 2.76"od x 1.6"id x 6.69"L 10 Micron Nominal

9ELDP4040101 Filter Element 3.54"od x 2.28"id x 7.48"L 10 Micron Nominal

9ELDP5040002 Filter Element 4.17" od x 2.83" id x 7.0 L 10 Micron Nominal

9ELDP5040001 Filter Element 4.17"ood x 2.83"id x 9.73"L 10 Micron Nominal

9ELWA5040001 Filter Element 4.17"ood x 2.83"id x 9.73"L Water Absorbing

9ELWA5040002 Filter Element 4.17" od x 2.83" id x 7.0 L Water Absorbing

9ELWR5040401 Filter Element 4.00"ood x 2.83"id x 21.6"L Water Absorbing


N E W !

35



CAT Filters Threading Dimension Gasket ADD-Vantage 9000Reusable/Cleanable

077-3058 1 1/2 x 16 5 x 7 none 9ADV9-926170077-3492 1 x 12 3 x 5 2.81 - 2.42 9ADV9-B262093-7521 1 1/8 X 16 4 X 7 2.83 - 2.46 9ADV9-B260102-2828 1 3/8 x 12 4 x 9 2.76 - 2.48 9ADV9-8878108-1153 1 3/4 x 12 11.63 L X 4.77 3.39 - 3.11 9ADV9-0973121-9868 1 3/8 X 12 4 X 6 2.76 - 2.48 9ADV9-8878126-1813 2 x 12 9.52 L X 3.13 3.13 - 1.86 9ADV9-1814126-1814 2 x 12 9.52 L X 3.13 3.13 - 1.86 9ADV9-1814126-1815 1 3/8 X 12 4 X 6 2.76 - 2.48 9ADV9-8878126-1816 1 3/4 x 12 5 x 8 3.34 - 3.13 9ADV9-6636126-1817 1 3/4 x 12 5 x 12 3.39 - 3.11 9ADV9-0973126-1818 1 3/8 x 12 4.7 x 11.6 2.76 - 2.48 9ADV9-8878129-0373 1 X 14 4.25 X 11.3 3.5 - 3.18 9ADV9-0373130-3212 2 x 12 3 x 9 3.13 - 1.86 9ADV9-1814133-5673 1 X 14 4.25 X 11.3 3.5 - 3.18 9ADV9-0373134-3014 1 3/4 x 12 5 x 12 3.35 - 3.11 9ADV9-0973144-0832 1 1/2 x 16 5 x 7 none 9ADV9-926170144-6691 1 3/8 X 12 4 X 6 2.76 - 2.48 9ADV9-8878152-6902 1 3/4 x 12 5 x 14 3.34 - 3.11 9ADV9-0973156-0214 1 3/8 x 12 4 x 9 2.76 - 2.48 9ADV9-8878185-0337 2 X 12 3 X 9 3.13 - 1.86 9ADV9-1814198-3188 1 1/2 x 16 5 x 11 none 9ADV9-926170L937-521 1 1/8 x 16 3.69 x 5.2 2.81 - 2.42 9ADV9-B2601G-8878 1 3/8 x 12 4 x 9 2.76 - 2.48 9ADV9-88781P-2299 1 x 14 3.65 x 7 2.81 - 2.42 9ADV9-10001R-0658 1 1/8 - 16 4.25 x 10.3 3.89 - 3.55 9ADV9-PH49A1R-0712 1 x 14 9.43L X 3.72" 2.81 - 2.42 9ADV9-10001R-0713 1 1/8 - 16 3.69 x 5.2 2.81 - 2.42 9ADV9-B2601R-0714 1 1/8 - 16 4.28 x 6 3.97 - 3.59 9ADV9-PH49A1R-0716 1 1/2 -16 5.3 x 12 4.31 - 3.92 9ADV9-40051R-0734 1 X 12 5.35L X 3.66 2.81 - 2.42 9ADV9-B2621R-0739 1 1/8 x 16 4.282 x 10.3 3.96 - 3.58 9ADV9-PH49A1R-0749 1 x 14 3.68 x 9.5 2.83 - 2.46 9ADV9-10001R-0750 1 x 14 3.68 x 7 2.83 - 2.46 9ADV9-10001R-0751 7/8 X 14 3.1 X 7.0 2.5 - 2.25 9ADV9-07511R-0755 1 3/8 x 16 5.3 x 12 4.28 - 3.9 9ADV9-07551R-0762 1 X 14 3.7 - 10.75 3.6 - 3.03 9ADV9-07621R-0769 1 X 14 4.24 X 9.90 4.25 - 3.68 9ADV9-07691R-0771 1 X 14 4.25 X 9.37 4.24 - 3.68 9ADV9-07691R-1807 1 1/8 x16 4 x 10.38 3.97 - 3.59 9ADV9-PH49A1R-1808 1 1/2 x 16 5.3 x 12 4.31 - 3.92 9ADV9-35661W-2660 1 1/2 x16 5.3 x 12 4.31 - 3.92 9ADV9-35661W-8845 1 3/8 x 16 4.66 x 9.75 4.32 - 3.85 9ADV9-0755207-5035 1 3/4 x 12 5 x 14 3.34 - 3.11 9ADV9-0973223-7809 1 1/2 x 16 5 x 7 none 9ADV9-926170225-4118 1 3/4 x 12 5 x 12 3.38 - 3.10 9ADV9-0973


ISO 9000 • To order any other items not listed above, please contact us.

36



CAT Filters Threading Dimension Gasket ADD-Vantage 9000Reusable/Cleanable

244-4484 1 1/2 x16 4.65 x 11.73 4.32 - 3.85 9ADV9-3566272-1788 1 1/2 x 16 5.3 x 12 4.31 - 3.92 9ADV9-4005275-2604 1 1/2 x 16 5.3 x 12 4.31 - 3.92 9ADV9-40052P-4004 1 1/8 - 16 4.25 X 10.3 3.89 - 3.55 9ADV9-PH49A2P-4005 1 1/2 x 16 5.3 x 12 4.31 - 3.92 9ADV9-40052Y-8096 1 1/8x 16 4.25 x 10.3 3.89 - 3.55 9ADV9-PH49A2Y-8097 1 1/2 x16 5.3 x 12 4.31 - 3.92 9ADV9-40052Y-8670 1 x 14 3.66 x 6.85 2.81 - 2.42 9ADV9-1000326-1643 1 X 14 4.25 x 9.3 4.25 -3.85 9ADV9-1643326-1644 1 x 14 4.25 x 7.6 4.25 - 3.7 9ADV9-16434I-3948 2 x 12 3 x 9 3.13 - 1.86 9ADV9-18144I-3950 2 x 12 3 x 9 3.13 - 1.86 9ADV9-18144T-6788 1 1/2 x 16 5 x 7 none 9ADV9-9261704T-6915 1 1/8 X16 4 X 6 2.72 - 2.41 9ADV9-B2607W-2326 3/4 x 16 3.81 x 6.78 2.82 - 2.42 9ADV9-B2377W-2327 3/4 x 16 3.66 x 5.35 2.81 - 2.41 9ADV9-B2379N-5570 1 1/8 x 16 3.81 x 5.22 2.81 - 2.42 9ADV9-B2379N-6007 1 1/8 x 16 4.28 x 5.78 3.97 - 3.59 9ADV9-PH37869T-0973 1 3/4 x 12 11.63L X 4.77 3.39 - 3.11 9ADV9-09739T-6636 1 3/4 x 12 5 x 8 3.34 - 3.13 9ADV9-66369T-8578 1 1/2 x 16 5 x 7 none 9ADV9-9261709U-5870 1 1/2 x 16 5 x 11 none 9ADV9-926170L9U-6983 1 1/2 x 16 5 x 11 none 9ADV9-926170L9U-6984 1 1/2 x 16 5 x 11 none 9ADV9-926170L9U-6985 1 1/2 x 16 5 x 11 none 9ADV9-926170L

CAT Filters Element Dimension ADD-Vantage 9000Reusable/Cleanable

054-1719 element 9.02L X 1.61 X 3.85 9ELSSK409X25077-5479 element 9.02L X 1.61 X 3.85 9ELSSK409X25086-3940 element 9.02L X 1.61 X 3.85 9ELSSK409X25094-4412 element 17.7L x 5.8 x 4.3 9ELSS5818x40132-8875 element 9.25L x 4.0 x 2.27 9ELSS773X40132-8876 element 9.0L x 5.07 x 3.34 9ELSS778X40134-0964 element 8.03L 3.1 X 1.71 9ELSS96008X25139-1536 element 11 X 5.07 X 3.34 REVERSE FLOW 9ELSS722X40139-1537 element 7.0 X 5 1/8 X 3 3/8 9ELSS5077X25167-2009 element 9.0 X 6.84 X 3.94 9ELSS709X40179-9806 element 16 3/4 X 5 5/8 X 3 7/8 9ELSS9806X25249-2337 element 9.0 X 6.75 X 4.25 REVERSE FLOW 9ELSS7409X25328-3655 element 10.5 X 5.0 X 2.0 9ELSS1809X251M-9156 element 9.25L x 4.0 x 2.27 9ELSS773X251R-0719 element 9.25L x 4.0 x 2.27 9ELSS773X401R-0722 element 11 X 5.07 X 3.34 9ELSS722X40



37



1R-0726 element 10 1/4 X 7 3/8 X 2 7/8 9ELSS726X401R-0728 element 9.0 X 3.0 X 1.6 9ELSS728X401R-0732 element 9.0 X 6.84 X 3.94 9ELSS709X251R-0735 element 7.0 X 5. 0 X 3.34 9ELSS507X251R-0741 element 9.0 X 5.0 X 3.34 9ELSS778X401R-0746 element 5.65 X 3.0 X 1.06 9ELSS746X401R-0756 element 9.0 X 3.0 X 1.6 9ELSS728X401R-0773 element 9.25L x 4.0 x 2.27 9ELSS773X401R-0774 element 11 X 5.0 X 3.34 9ELSS774X401R-0777 element 7.0 X 5.0 X 3 3/8 9ELSS507X251R-0778 element 9.0L x 5.07 x 3.34 9ELSS778X401R-1809 element 10.5 X 5.0 1.15 9ELSS1809X251S-9150 element 9.0 X 3.0 X 1 7/16 9ELSS9150X252J-1560 element 9.0L x 5.07 x 3.34 9ELSS778402M-3943 element 9.25L x 4.0 x 2.27 9ELSS773402P-5835 element 5.65 X 3.0 X 1.06 9ELSS5834X254A-0332 element 9.0 X 3.0 X 1 7/16 9ELSS9150X254J-0806 element 9.0L x 5.07 x 3.34 9ELSS778404J-6064 element 9.0L x 5.07 x 3.34 9ELSS778404P-2839 element 10 5/5 X 7 3/8 X 2 7/8 9ELSS726X40

4T-3131 element 9.25L x 4.0 x 2.27 9ELSS773404T-3132 element 9.0L X 5.07 X 3.34 9ELSS778254T-3133 element 9.0 X 6 3/4 X 4.0 9ELSS709X254T-3134 element 11 X 5.0 X 3.34 REVERSE FLOW 9ELSS722X405S-0484 element 9 5/16 X 4.0 X 1 5/8 9ELSS484X407J-0670 element 9.0 X 6 3/4 X 4.0 9ELSS709X257J-0732 element 9.0 X 6.84 X 3.94 9ELSS709X257M-3800 element 9 5/16 X 4.0 X 1 5/8 9ELSS484X407N-7500 element 10 5/16 X 7 3/8 X 2 7/8 9ELSS726X409F-6700 element 9 5/8 X 4.0 X 1 5/8 9ELSS484X409H-1252 element 6.5 X 3 5/16 X 1 1/16 9ELSS8792X259J-5461 element 11 X 5.0 X 3.34 9ELSS722X409M-9740 element 9.25 X 4.0 X 2.27 9ELSS773X40

CAT Filters Element Dimension ADD-Vantage 9000Reusable/Cleanable


38



Customers Who Have Been Using The OEI Product For Years and Continue To Do So

Customer List

Mining Industry: Atlas Copco Drilling, Arch Coal, Barrick Gold Corporation, BHP Billiton, Billiton Mitsubishi Alliance, Buckskin Mining Company, Cliff Mines, Cloud Peak Energy, Consol Energy, Filtervac International Inc, Freeport-McMoRan Copper & Gold, Grande Cache Coal Corporation, Homax Oil Sales Inc, Iron Ore Company of Canada, Joy Global Inc, Kiewit Mining Group, Mainland Sand & Gravel Ltd, Rio Tinto, Suncor Energy Inc, The Mosaic Company, Mount Polley Mining Corporation, Peabody Energy Inc, Phelps Dodge, Teck Resources Ltd, Vale Mining Company, Westmoreland Coal Company, etc.

Oil and Gas Industry: Alliance Pipeline, Canyon Technical Services Ltd, Dessert Industries Inc, ECOQUIP Rentals and Sales Ltd, Enbridge Inc, ESSO Canada, Hallibur-ton Group Canada, Kinder Morgan Pipelines, Lufkin Industries Ltd, National Oilwell Varco, Pemex, Petrobras, Pioneer National Resources, Precision Drilling Corpora-tion, Schlumberger, Sphere Drilling, Spectra Energy Corp, Stellarton Technologies Inc, STEP Energy Services, Suncor Energy Inc, Talisman Energy Inc, Trican Well Ser-vice, etc.

Food Industry: Barilla Ge R Fratelli, Big Rock Brewery, Bonduelle, Carnitech A/S, Cavendish Farms, Ital Pizza, Marel, Pinnacle Foods Inc, PT. Bentoel Prima, PT. Bin-tang Terang Gemilang, PT. Santos Jaya Abadi Safeway, St-Huberts, Svila srl Pizza Plant, etc.

Construction Industry: Kinecor, LaFarge, Marlin Engineered Technologies, Rio Tinto

Manufacturing Industry: Ariston, Cavendish Farms, Danieli Corporation, EVRAZ HP, Linamar, PT. Adi Prima Suraprinta, PT. Indorama Synthetic, PT. Tjiwi Kimia, SACMI, etc.

Transportation Industry: Bombardier Transportation, City of Houston, Great West-ern Kenworth, Town of Okotoks



Scrubber Flow Rates

ScrubberModel 5SC-

349SCL5SC-

12SCL5SC-

24SCL5SC-

36SCL5SC-

212SCL5SC-

224SCLViscosities Base

cSt @ 40CWater, Coolant Deisel Fuel (1 - 30 St)Single Pass Filtra-tion

GPM 8 21 40 60 50 98

Multi Pass Filtration 30 81 95 122 200 400

Engine, Gear andHydraulic Oil / cStSAE 10 (40 - 110 cSt)Single Pass Filtra-tion

GPM 7 20 38 55 50 98


SAE 20 (220 cSt)Single Pass Filtra-tion

GPM 6 15 30 45 40 70



GPM 5 12 20 25 25 40



GPM 3 6 10 12 12 20


Gear Oil (1000 cSt)Single Pass Filtra-tion

GPM 0 3 5 6 8 15


LIMITED WARRANTY3 Year Limited Warranty on 2000,3000,4000,5000 and 8000 Series inclusive plus ADD-Vantage 9000 Series

(Ten year life expectancy).1 Year Limited Warranty on 500,800,900 and 7000 Series

(Five year life expectancy).

The exclusive remedy for breach of this warranty is replacement of any product which the buyer, within the warranty period, has noti�ed the Seller in writing to be defective, and which the Seller has determined to be defective. If the buyer has submitted a warranty registration card for the product, the notice of the defect must include a proof of purchase. The Buyer will be responsible for all costs of shipment of replacement parts. In no event will the Seller’s liability for any damage exceed the purchase price of the product. SELLER WILL NOT BE LIABLE TO THE BUYER FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES INCLUDING, WITHOUT LIMITATION, LOST REVENUES OR PROFITS, EXPENSES RELATED TO TRAVEL, AND LOSS DUE TO PERSONAL INJURY. The sole purpose of the stipulated remedy shall be to provide the Buyer with free replacement of defective parts in the manner provided herein. This exclusive remedy shall not be deemed to have failed of its essential purpose so long as the Seller is willing and able to replace defective parts in the prescribed manner. SUCH WARRANTY IS EXTENDED ONLY TO THE ORIGINAL BUYER OF THE FILTER MASTER AND DOES NOT EXTEND TO A REPURCHASER OF THE PRODUCT. THE WARRANTIES IN THIS AGREEMENT ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND SUCH OTHER WARRAN-TIES ARE EXPRESSLY DISCLAIMED. THE SELLER HAS NOT MADE AND DOES NOT HEREBY MAKE ANY OTHER REPRESENTATION, WARRANTY OR COVENANT WITH RESPECT TO THE CONDITION, QUALITY, DURABILITY, DESIGN, OPERATION, CAPACITY, FITNESS FOR USE, OR SUITABILITY OF THE EQUIPMENT. THIS WARRANTY DOES NOT COVER PARTS THAT ARE SUBJECT TO NORMAL WEAR AND/OR DETRIMENTAL EFFECTS OF EROSION, CORROSION OR TEMPERATURE. Custom Products will have their own warranty supplied.

DEALER INFORMATION:

Since 2004

worldwide distribution - renox · worldwide distribution. 1) ... (welding, slag, grindings)....

Documents