written by: teagan allen...step 2 unscrew the eighteen 10mm screws that secure the back panels using...

6
SwagTron T1 Wheel Replacement Replacing the wheel of the SwagTron T1. Written By: Teagan Allen SwagTron T1 Wheel Replacement Draft: 2017-06-07 Guide ID: 88861 - This document was generated on 2020-11-18 05:02:55 PM (MST). © iFixit — CC BY-NC-SA www.iFixit.com Page 1 of 6

Upload: others

Post on 21-Aug-2020

2 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: Written By: Teagan Allen...Step 2 Unscrew the eighteen 10mm screws that secure the back panels using a Phillips #2 screwdriver. The screws are tightly in place. It will take effort

SwagTron T1 Wheel ReplacementReplacing the wheel of the SwagTron T1.

Written By: Teagan Allen

SwagTron T1 Wheel Replacement Draft: 2017-06-07Guide ID: 88861 -

This document was generated on 2020-11-18 05:02:55 PM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 1 of 6

Page 2: Written By: Teagan Allen...Step 2 Unscrew the eighteen 10mm screws that secure the back panels using a Phillips #2 screwdriver. The screws are tightly in place. It will take effort

INTRODUCTION

This guide will outline how to replace the wheel of the SwagTron T1 hoverboard. This may benecessary for any critical damage done to the hoverboard's wheel.

TOOLS:Phillips #2 Screwdriver (1)Allen Wrench (1)

SwagTron T1 Wheel Replacement Draft: 2017-06-07Guide ID: 88861 -

This document was generated on 2020-11-18 05:02:55 PM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 2 of 6

Page 3: Written By: Teagan Allen...Step 2 Unscrew the eighteen 10mm screws that secure the back panels using a Phillips #2 screwdriver. The screws are tightly in place. It will take effort

Step 1 — Back Panels

Ensure that the SwagTron is off.

Turn the SwagTron upside down tosee the underside.

Step 2

Unscrew the eighteen 10mm screws that secure the back panels using a Phillips #2 screwdriver.

The screws are tightly in place. It will take effort to screw them out.

The panel is still attached to the SwagTron by wires that go to the motherboard.

Carefully lift the panels off

SwagTron T1 Wheel Replacement Draft: 2017-06-07Guide ID: 88861 -

This document was generated on 2020-11-18 05:02:55 PM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 3 of 6

Page 4: Written By: Teagan Allen...Step 2 Unscrew the eighteen 10mm screws that secure the back panels using a Phillips #2 screwdriver. The screws are tightly in place. It will take effort

Step 3

Follow the wires from the panels to the motherboard.

You may need to cut any zip ties that are holding the wires together.

There is one connection on the battery side and three on the other side that must be removed.

These connections may be difficult to remove. Try to securely press the connection and pull firmly.

Your back panels are now completely removed.

Step 4 — Wheel

Using your Phillips #2 screwdriver, remove the four 1cm screws that attach the gyroscope and itsblack case to the hoverboard.

Carefully remove this component and set it off to the side.

SwagTron T1 Wheel Replacement Draft: 2017-06-07Guide ID: 88861 -

This document was generated on 2020-11-18 05:02:55 PM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 4 of 6

Page 5: Written By: Teagan Allen...Step 2 Unscrew the eighteen 10mm screws that secure the back panels using a Phillips #2 screwdriver. The screws are tightly in place. It will take effort

Step 5

Using your H 6.0 allen wrench, remove the four 20mm black bolts shown in the picture.

Take off the iron plate holding the wheel in place.

Remove the Motor/Wheel and set it aside close by to the hoverboard.

The wires from the Motor/Wheel should still be connected to the motherboard.

These bolts are very tight, it may be difficult to remove them. Try using a tool with a long handle.

Step 6

Slide the protective plastic off the connectors on the marked wires (green, blue, and yellow) usingyour hands or a set of tweezers.

The connectors on the wires of your hoverboard may be different from those shown in the pictureson the left due to differences in manufacturing.

Separate the set of marked green, blue, and yellow wires from their connectors.

SwagTron T1 Wheel Replacement Draft: 2017-06-07Guide ID: 88861 -

This document was generated on 2020-11-18 05:02:55 PM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 5 of 6

Page 6: Written By: Teagan Allen...Step 2 Unscrew the eighteen 10mm screws that secure the back panels using a Phillips #2 screwdriver. The screws are tightly in place. It will take effort

To reassemble your device, follow these instructions in reverse order.

Step 7

Finally separate the last connector shown on the left.

Your wheel is completely removed; slide in a new Motor/Wheel into the slot and follow the previoussteps in reverse order.

Make sure the replacement wheel is snug. Neither rubbing on the outer rim nor on the side of thehoverboard.

SwagTron T1 Wheel Replacement Draft: 2017-06-07Guide ID: 88861 -

This document was generated on 2020-11-18 05:02:55 PM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 6 of 6