www.anton-paar.com b78iv001en-b furnace rheometer system frs 1600

www.anton-paar.comB78IV001EN-B

Furnace Rheometer SystemFRS 1600


Cooling Concept of the Air Bearing DSR 301

Specifications DSR:

Max. torque 200 mNm

Min. torque 0.05 µNm

Max. speed with FRS 300 1/min

Normal force range 0.01 to50 N

Heat shield

Air and water cooled rheometer head fixture

Air cooled coupling

(Fluid circulator VT2 running at 20 °C required)

Side view rheometer part Top view rheometer part

Rheometer head DSR


The Furnace : Carbolite STF 16/180

Power Cable

Working Tube

X-Axis Movement

(vertical)

The furnace The temperature control unit

Temp. Display

Specifications Control Unit:

Power Connection 380V, 21A

Heating Pulsed Current

Connection to DSR Serial

Specifications Furnace:

Max. Temperature 1600°C

Min. Temperature 300°C

Inert Gas e.g.: Ar, N2


Preparation and Measurement of the Sample

Set zero gap Lift position Sample fillingSample heating, melting

Measuring position by NF control, start measurement

Lift position (NF control)

Reference position, cleaning

All you have to do is…


Vertical Movement Concept

Reference position for cooling and cleaning

Pne

uma

tic li

ft u

p to

fin

al c

up p

ositi

on

Pne

uma

tic li

ft d

own

to

hea

ting

po

sitio

n

Heating position Measuring position

Normal force controlled final positioning by stepper motor driven elevating thread

Fur

nace

mo

ved

to

park

pos

ition


Overall View

Furnace

Temperature range 300°C to 1600°C

Temperature control Eurotherm

Total lenght heat tube 600 mm

Heated lenght heat tube 180 mm

Constant temperature 80 mm

Rheometer Head

DSR measuring head Air bearing

Test modesRotation and oscillation

Software controls instrument and furnace

▸ Water measurement at 20 °C

From very low rotating speeds up to 300 1/s

Regarding the 300 mm shaft perfect concentricity and measurement results.


Measuring Systems for high Viscosity Samples as e.g. Glass melts, Lava, Basalts

Cup:

C-CC30/AO/FRSd(i): 30 mm, d(o): 40 mm

h(i): 60 mm

C-CC30/CA/FRSd(i): 30 mm, d(o): 40 mm

h(i): 60 mm

Bob:

D-CC11/AO/FRSd: 11.4 mm L: 30 mm

D-CC15/AO/FRSd: 15 mm L: 20 mm

D-CC11/CA/FRSd: 11.4 mm L: 30 mm

D-CC15/CA/FRSd: 15 mm L: 20 mm

C-CC Cup-Conc. Cylinderxx Inner Diameter in mmAO Aluminum oxideCA Carbon FRS for FRS

D-CC Disposable-Conc. Cylinderxx Inner diameter in mmAO Aluminum oxideCA Carbon FRS for FRS

C-CC30/CA/FRS/XLC-CC30/OA/FRS/XL

d(i): 30 mm, d(o): 40 mm h(i): 80 mm

Other materials and dimensions on request.


d(i): 30 mm, d(o): 40 mm h(i): 80 mm

Cups for powders and bulk goods

(Larger volume in a non-molten state)


d(i): 30 mm, d(o): 40 mm h(i): 80 mm


Standard Measuring Systems for low Viscosity Samples as e.g. Metal Melts

Bob:

D-CC25/CA/FRSd: 25 mm L: 37.5 mm

D-CC27/CA/FRSd: 26.66 mm L: 40 mm

D-CC Disposable-Conc. Cylinderxx Inner cylinder diameter in mmAO Aluminum oxideCA CarboneFRS for FRS

D-CC27.6/AO/FRSd: 27.6 mm L: 41.4 mm

Other materials and dimensions on request.

D-CC29/CA/FRSd: 29 mm L: 41.4 mm

D-CC27.6/CA/FRSd: 27.6 mm L: 41.4 mm


Possible applications: ▸ metal melts▸ glass melts▸ coal ash, slags▸ lava, basalte, rocks

Applications, Impressions and Standards

( )

(Withdrawn 2009)


▸ The FRS is the only reasonable decision for metal melts, because of the low viscosities which can

only be measured with an air bearing rheometer

▸ Potential costumers: ▸ Universities and other research centres ▸ Metal industry:

▸ Steel and Iron (melting points: ~1510 °C and 1530 °C )

▸ Copper (melting point: 1083 °C )▸ Silicium (melting point: 1410 °C)

▸ Cross-selling potential: CTD 600 and CTD 1000 (e.g. for Aluminium or Zinc and other lower melting materials)

▸ Until now, metal melts are measured with so called Oscillating Vessel Viscometers and Flow Cups (assuming Newtonian behaviour)

Metal (1)


▸ Argumentation and explanation: ▸ Based on the latest scientific

findings some metal and alloy melts exhibit non-Newtonian flow behaviour

▸ This is a fundamental finding, as most theories and all measuring techniques are based on the assumption that metal and alloy melts are Newtonian liquids

▸ Until now this effect could not be measured with competitor instruments, as they are all based on ball bearing rheometer heads

▸ This effect has not only an impact on academia, but also on the metal processing industry. For example during the casting process a wide spectrum of shear rates can be observed, so the exact flow curve needs to be determined

Metal (2): Measurements

Figure: Quadruple repetition of steel measurements at 1537 °C - Please note the non-Newtonian behaviour!


▸ The FRS delivers great results measuring glasses

▸ Potential costumers: ▸ Universities and other research centres ▸ Industry: Development of special glasses (standard glasses don’t need to

be measured anymore, as their viscosity can be calculated by equations, if the exact chemical composition is known)

Glass (1)


Argumentation and explanation: ▸ Glass is a Newtonian liquid▸ The viscosities at different

temperatures are from interested▸ Glass standards are available to

conform the validity of the measurements

▸ The FRS can measure glass according to the following standards:

▸ ASTM C1276 (withdrawn)▸ ASTM C965

▸ With the FRS one can determine the following additional parameters:

▸ Crystallisation point ▸ Melting point

Glass (2): Measurements

Figure: Viscosity curve of two different glasses during cooling


▸ The FRS can be used to measure slags and coal ash to determine their properties for their further processing

▸ Potential costumers: ▸ Universities and other research centres ▸ Industry:

▸ Slag: ▸ By-product of the iron und steel production▸ Range of application: Additives for cement, street building, glass industry,

brigs, fire proved materials, isolation materials….▸ Coal Ash:

▸ By-product of coal combustion (e.g. for Power generation or other industrial applications)

▸ Range of application: e.g. Alternative to cement, usage in brigs, asphalt, flow able film shingles – building material for monuments (e.g. freedom tower NY-city)….

Slags and coal ash (1)


Argumentation and explanation: ▸ Good and reliable results for

slag and coal ash▸ Slag or coal ash is sometimes

“splashing” and “bubbling” – the advantage of our instrument is that we are operating in a working tube as protection for the heating elements

▸ The working tube also protects the heating elements from corrosive gases released by the sample, that may cause severe damage

Slags an coal ash (2): Measurements

Figure: Viscosity curve of coal ash at 1400 °C


▸ High safety, reliability and quality (of the instrument and the results)

▸ Large shear rate range because of the air bearing

▸ Normal force control: Sample shrinkage or expansion is recognized and measured by the normal force sensor. With this function the melting point can be determined

▸ Toolmaster: DSR employs ToolmasterTM functionality.

▸ Oscillation measurements are possible

▸ Measurement of non-Newtonian material down to very low viscosities possible

▸ Operation in a working tube – to handle even splashing and bubbling materials

Conclusion and features (1)


▸ Easy and safe handling (CE certified)

▸ Measurement according to the following standards:▸ ASTM C1276 (withdrawn)▸ ASTM C965

▸ Disposable measuring systems (for saving time -> no cleaning is required and for solidification experiments)

▸ Temperature sensor / Temperature calibration: The FRS comes with a factory temperature calibration. The instrument sets the furnace temperature according to the calibration. The software displays the sample temperature

▸ AGC coefficient: The length change due to temperature of the measuring system is automatically compensated by the AGC function

Conclusion and features (2)


▸ Look out for potential costumers (according to the applications mentioned before) in your region

▸ Address them before their budget run

▸ Look for information material like application reports in the extranet or ask for reference measurements and additional information. We are constantly adding new application reports and marketing material

▸ Try to influence tenders according to our features and strengths and prepare yourself with arguments to explain the price differences to the competitors

▸ Demos, installations and the costumer support is handled in teamwork with Graz (Peter Brandes and Elke Riedl)

▸ Please update us about your FRS opportunities and give us your and the costumers feedback about the FRS. Your opinion and your information are very valuable for us

How to sell an FRS?


▸ One FRS project generates the turnover of two to three MCR projects

▸ If the customer is really interested there is a good chance to sell a FRS

▸ The FRS ensures safe operation and high quality (also in comparison to the competitors, a list will be handed out to all participants)

▸ You will get all the support you need from Graz – together we can win more projects

▸ Our team here in Graz is going to build up collaborations and further application knowledge in the high temperature rheometry area – be part of it!

Chances

www.anton-paar.com b78iv001en-b furnace rheometer system frs 1600

Documents

dcc25cafrs d

dcc11aofrs d

dcc15aofrs d

dcc11cafrs d

dcc15cafrs d

dcc27cafrs d

dcc29cafrs d

frs dcc27