INSTRUCTION MANUAL SUPPLEMENTARY SHEETUse this XB9E Supplementary Instruction Sheet along with the standard XB9 instruction manual included in the kit. This Supplementary Sheet highlights and explains new updated steps and you should refer to them while building your XB9E kit. Each step in this Supplementary Sheet indicates the section to which the updated step refers.

Please note that this kit does not include an air filter oil and other parts used for nitro XB9 version, and also does not include pinion gear and body.

New and Improved PartsAll of these parts are new or updated from the previous versions. Each of these parts feature their corresponding part number which can be used to re-order the parts. You can also refer to the complete exploded views.

#356194XB9E ALU MOUNT FOR RECEIVER BOX

8. CENTER DIFFERENTIAL PAGE 26-27

8. CENTER DIFFERENTIAL NEW STEP

358783

MOTOR(not included)

961032908312Do not follow the original manual,

assembly this section following just these steps.

908308903412 355011 903412

354010

354053

903308

902330

352290

358782

355712-17(not included)

#336000COMPOSITE RECEIVER CASE - V2

#356151XB9E COMPOSITE BATTERY PLATE

#358783XB9E ALU MOTOR MOUNT PLATE

#351155XB9E CHASSIS SIDE GUARDS L+R

#354053 XB9E GRAPHITE CENTER DIFF MOUNTING PLATE

#356195XB9E ALU BATTERY PLATE HOLDER

#911408HEX SCREW FLANGED SH M4x8 (10)

#356118XB9E GRAPHITE RECEIVER CASE TOP PLATE

#358782XB9E ALU MOTOR MOUNT

SCH 3x8SB 4x4

8. CENTER DIFFERENTIAL

8. CENTER DIFFERENTIAL

8. CENTER DIFFERENTIAL

NEW STEP

NEW STEP

NEW STEP

SFH3x8NOTE ORIENTATION

NOTE ORIENTATION

SH3x30

SFH4x12

S 3.2

SCH 3x12

GEAR MESH ADJUSTING

Adjust gear mesh so there is minimal play between the gears.

Too tight gear mesh will put excessive strain on all parts and damage the parts. Too loose gear mesh may result in stripped gears.

8. CENTER DIFFERENTIAL

9. FUEL TANK & ENGINE PAGE 28-30

NEW STEP

10. RADIO CASE PAGE 31 STEP 1

SERVO GROMMET(not included)

356118

960040

960040

902314

352460352670

960030

356194

903410356151

903416

902308

306310

902312

902308

902308

907206

336000

903410

911408356195

356120

902312

302611

352670352460356200

STEERING SERVO(not included)

LiPo BATTERY PACK(not included)

SPEED CONTROLLER(not included)

356160

SERVO SCREW(not included)

Do not follow the original manual, this section refers to nitro engine installation.

Use these holes only

SFH3x10

SFH3x10

SFH3x14

SFH3x14

10. RADIO CASE

10. RADIO CASE PAGE 29 STEP 3,4

NEW STEP

10. RADIO CASE PAGE 32 STEP 1,2

If the receiver box has 2 different-size openings for cable entry (narrow and wider), cut away the tab for the appropriate opening to allow the cables to fit properly.

DOUBLE-SIDED TAPE(not included)

TIE STRIPE(not included) SPEED CONTROLLER

(not included)

LiPo BATTERY PACK(not included)

Cut the foam as needed to fill in space between the batteries and holder.

VELCRO BATTERY STRAP

CUT HOLE FOR CABLES

RECEIVER(not included)

Antena

SH3x12

SERVO SCREW(not included) SH

3x8

2x6

SH3x8 SH

3x8

SFH4x10

SH3x14

SFH4x16

SHF4x8

INSTRUCTION MANUAL SUPPLEMENTARY SHEETUse this XB9E Supplementary Instruction Sheet along with the standard XB9 Instruction Manual.New and Improved PartsAll of these parts are new or updated from the previous versions.

#355261Alu Wheel Nut - Ribbed - Hard Coated (2)

2mm2mm

2mm2mm

INITIAL POSITION

INITIAL POSITION

#352215XB9 Composite 2-Hole Caster Block 16° Right

#352225XB9 Composite 2-Hole Caster Block 16° Left

#352253XB9 Composite Steering Block Right

#352263XB9 Composite Steering Block Left

#352612Adjustable Turnbuckle 45mm M4 L/R - HUDY Spring Steel™(2)

# 352621Adjustable Turnbuckle 58mm M5 L/R - HUDY Spring Steel™(2)

# 352631Adj. Turnbuckle 64mm M5 L/R - HUDY Spring Steel™ - V3 (2)

3. REAR SUSPENSION

4. REAR SUSPENSION

Page 13 / Step 1

Page 15 / Step 2

2mm2mm

Left threadRight thread28mm 28mm

Left thread Right thread

INITIAL POSITION

DETAIL

INITIAL POSITION21

6. FRONT SUSPENSION

5. FRONT SUSPENSION

7. STEERING

7. STEERING

Page 21 / Step 1

Page 18 / Step 1

Page 25 / Step 2

Page 25 / Step 3

DO NOT USE ShIM 1MM 1mm2mm

BUMP STEER

ShIM UNDER STEERING PLATE

mm2