y pimped 3d printed rc truck v4.1 - original by · rodend idea is "stolen" with...
TRANSCRIPT
pstimpel
Pimped 3D PrintedRc Truck V4.1 -Original byMrCrankyface
VIEW IN BROWSER
updated 17. 6. 2019 | published 17. 6. 2019
PRUSAPRINTERS
Summary
Pimped version of the OpenRC TruckV4 made by Mr.Crankface. Replacedrods by 3d printed ones, some adjustments to the center gearbox, andmost important I added a second gearbox to allow the use of 540 motors.
Hobby & Makers > RC & Robotics
Based on the fantastic work of Mr.Crankyface this is version 4.1 (?) of thewonderful truck. It was pimped in several ways.
Maiden drive with these mentioned addons: https://www.youtube.com/watch?v=mJC_t949Rj8
First of all, I was too greedy to spend any money on panhard-rod or theother rods including the stearing rod, so I used 3d printed ones. Therodend idea is "stolen" with permission by the guys who made the Rancher4x4, so called 3dsets.com. The Rancher is another fun build, by the way.When I am done with driving the truck, I turn my Rancher on, usually.
Thanks a lot for the permission, @3dSets.com! Appreciated!
The rods created using this idea are working as good as original rods, butare lots cheaper. Basically you print two "rodends" or "Ball joints" per rod,
3D M
ODEL
ONLY
and use a vise and the tool to pressfit the rodends into the holes of therods. Works fantastic. If you add a little grease those rodends go as easyas original ones. The tool needed to press the things together is 3d printedas well. Just take care to press the jooints into the rods the right direction.The flat surface of the joint is the one pointing to the desired mountingpoint - usually the frame or axle, while you insert the screw from the roundside, always! The rodends are printed with 10 perimeters and 100% infill,basically they are solid. The rods are printed with 4 perimeters, and 50%cubic infill. I was in need of some spacers to mount the suspensions, theywere too close to the frame on the upper side. So I created some spacersyou might find useful. You will need one per suspension.
STLs Tool: 12mm Rodend Balljoint Helper Rod end: Ball joint Rods for rearaxles and front axle, 3 pieces per axle: 64mm rod rodend Rods for rearaxles, 1 piece per axle, the one that is mounted above differentials: 75mmrod rodend Panhard rod: 75mm rod rodend Stearing rod: 85mm rod rodend
I was in need of some spacers to mount the suspensions, they were tooclose to the frame on the upper side. So I created some spacers you mightfind useful. You will need one per suspension.
STL Suspension spacer: Spacer Suspension TruckV4
Another tweak is addressing the kind of strange angle the gearbox ismounted compared to the axles - at least with the 80mm suspensions I amusing. So I added part to mount the gearbox a bit lower compared to theoriginal. Just print the gearbox extender, and replace the screws withM3x25 to mount the original gearbox to the frame with the extender in themiddle. The extender was printed using 2 perimeters an 15% cubic infill.
STL: CentralGearDistance TruckV4
On top I was not able to buy such a motor MrCrankyface was using.Instead I went for a 540 RC brushed motor, 35 turns, 9000rpm. Now, thiswas too much RPM, so I created another gearbox to put the RPM down abit before the power enters the original gearbox. The gearbox uses 6bearings 10x15x4mm. Once I put the final addon gearbox online, I will tellabout the printing settings as well.
STLs: t.d.b.
As you can see the second gearbox is ugly, and simply tied. Needs somemore beauty before I will release these files. Make sure to subscribe so youwon't miss the moment when I am finishing this (soon).
STL files for th Original TruckV4: https://www.thingiverse.com/thing:2935751
Model Files (.stl, .3mf, .obj, .amf) DOWNLOAD ALL FILES
79.6 KBupdated 17. 6. 2019
80.4 KBupdated 17. 6. 2019
91.3 KBupdated 17. 6. 2019
66.3 KBupdated 17. 6. 2019
40.3 KBupdated 17. 6. 2019
11.2 KBupdated 17. 6. 2019
70.8 KBupdated 17. 6. 2019
55.4 KBupdated 17. 6. 2019
75mm-rod-rodend-v1.stl
12mm-rodend-balljoint-helper-v2.stl
64mm-rod-rodend-v1.stl
75mm-rod-rodend-v2.stl
spacer-suspension-truckv4-v1.stl
centralgeardistance-truckv4-v2.stl
64mm-rod-rodend-v2.stl
85mm-rod-rodend-v3.stl
1.2 MBupdated 17. 6. 2019
The Author has not uploaded any G-codes.Try to search in User G-codes section or generate and upload yourown.
License
This work is licensed under a Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike
✖ | Sharing without ATTRIBUTION ✔ | Remix Culture allowed ✖ | Commercial Use ✖ | Free Cultural Works ✖ | Meets Open Definition
ball-joint.stl