you can obtain a board with actual material swatches by … · · 2016-10-14epdm reticulated foam...
TRANSCRIPT
EPDM
Reticulated Foam
2A1 Sponge Rubber
Water Resistant Hydro Foam *
2A2 Sponge Rubber
Soft EPDM
Anti-Squeak FeltSeat & Headrest Topper Foam *
Soft PVN / Vinyl Nitrile
EVA Foam
4 lb. HDPE
High Density Foam *
Low Perm Lok Cel *
Mini-Cell Polyethylene
Neoprene Sponge
Non-Woven Polyester
P.E.T. Fiber
Polyethylene
Poron
PVC
Reclaimed Rubber
Open Cell Natural Rubber
Mastic
Superseal
PVN / Vinyl Nitrile
2 lb. X-LinkedPolyethylene
The samples pictured below are a few of the numerous materials fabricated by Plastomer Corporation and Inteligente Technologies. They are all available with OEM approved pressure sensitive adhesives based on your specific substrate and surface shapes.You can obtain a board with actual material swatches by sending your request to [email protected] today.
Polyether Open Cell Foam *
Firmer Foams *
Reclaimed Foam
Good Tack PSA
High Tack PSA
High Temp PSA
High Humidity & High Temp PSA
Direct Coat PSA
A PSA to solve the most difficult
problem.
www.plastomer.com (734) 464-0700
5
6
7 14 21 28 35
34
33
32
31
30
4
3
2
1 8 15 22
9
10
11
12
13 20 27
19 26
17
16 23
24
2518
29
T E C H N O L O G I E S
* Plastomer EKOHFOAM® formulation available with sustainable & renewable components.
1 8 15 22 29C: MSAY 326D: SD2 - 209 PARA. 6.2F: ESA - M4D200 - BG: GMW 16750T: TSK 6712G - 1A40V: VAM Foam 1A 0B - 001
2
3
4
5
6
7 14 21 28 35
30
31
32
33
34
9 16 23
24
25
26
272013
12 19
18
1710
11
C: MSAY 335D: SD2 - 209 PARA.6.12D: SD2 - 209 PARA.6.13F: ESH - M4D291 - EG: GMW 16750V: VAM Foam 1A 0B - DC0002W: TLV - VW - 561W : TL - VW - 547
B: AA 04737C: MSAY 358F: ESA - M4D57 - AG: GMW 16750G: GMW 15058N: DDS 2360 (FETU - 02)
C: MSAY 309D: SD2 - 209 PARA. 6.13F: ESA - M4D57 - AG: GMNA GM223M (not for new design)G: GMW 16750G: GMW 16960
C: MSAY 545F: ESB - M4D75 - AG: GMW 16750
C: MSAY 558F: WSK - M2D460 - A (not for new design)F: WSS - M99P32 - CG: GMW 16750
C: MSAY 349F: WSK - M2D406 - AG: GMW 16750T: TSK 6712G - 1A40 - N
C: MSAY 551F: WSK - M4D649 - AG: GMW 15063
C: MSAY 551F: WSK - M4D649 - AG: GMW 15063
C: MSAY 551F: WSK - M4D649 - AG: GMW 15063
F: WSB - M4G109 - A2G: GMNA 99844208 (not for new design)
A: D1056 - 00 2A1C: MSAY 518F: WSK - M4D675 - AG: GMNA GM6075M
C: MSAY 551F: ESF - M8G156 - A, B, B2G: GMW 15063
C: MSAY 500F: ESB - M3G102 - AG: GMW 15473
A: D1056A: D1056 - 00 2A1A: D1056 - 00 2A2A: D1056 - 00 2A3C: MSAY 430D: SD2 - 207 PARA.6.10F: WSK - M2D419 - AT: TSM 1501 G
C: MSAY 550F: WSB - M3G212 - AG: GMW 15643T: TSK 6505 2A1 / 2A2
A: D1056 - 00 2B1A: D1056 - 00 2B2C: MSAY 516F: WSK - M2D419 - AG: GMW 15473T: TSM 1501 G
C: MSAY 500F: WSB - M3G102 - B2G: GMW 15473T: TSK 6505 G
A: D1056 - 07F: WSK - M2D419 - AG: GMW 15473T: TSM 1501 G
A: D1056 - 2A1C: MSAY 430D: SD2 - 207 PARA.6.1F: WSK - M2D419 - AG: GMW 15473T: TSM 1501 G
A: D1056 - 2A2C: MSAY 430D: SD2 - 207 PARA.6.2F: WSK - M2D419 - AG: GMW 15473T: TSM 1501 G
C: SAE J2558F: WSS - M99G133 - A3F: WSS - M2D476 - A2G: GMNA GMN10031
C: MSAY 552 / 550F: WSB - M3G102 - B (not for new design)F: WSB - M3G102 - B2G: GMW 15473
G: GMNA GM6420M (not for new design)G: GMW 16875T: In Development
C: MS - HZ 100F: WSS - M99P32 - A, B (not for new design)F: WSS - M99P32 - CG: GMW 14194
C: MS - HZ 100F: WSS - M99P32 - A, B (not for new design)F: WSS - M99P32 - CG: GMW 14194
C: MSAY 549AF: WSS - M2D496 - A1 - A10 (see Tech. Dept.)G: GMNA GM6098M (not for new design)G: GMW 14196
C: TBDD: SD2 - 209 PARA.6.16F: WSS - M2D224 - B1G: TBD
C: MSAY 335F: WSS - M99G133 - A3G: GMNA GM223M (not for new design)G: GMW 16960
C: MSAY 349 - C11 (PSA only)D: SD2 - 324 PARA.4.1.1.F: ESA - M11P19 - BG: GMW 14892
C: MSAY 349 - C12 (PSA only)D: SD2 - 324 PARA.4.2.2.F: ESA - M11P19 - BG: GMW 16443 Type 1
C: MSAY 349 - C21 (PSA only)D: SD2 - 324 PARA.4.3.4.F: WSA - M11P19 - CG: GMW 16443 Type 2
C: MSAY 349 - C22 (PSA only)D: SD2 - 324 PARA.4.3.3.F: WSA - M11P19 - CG: GMW 16443 Type 2
C: MSAY 324 - B21 (PSA only)D: SD2 - 324 PARA.4.2.3.F: ESH - M11P40 - A
C: Specify peel value desired.D: SD2 - 324 PARA.4.3.6.F: Specify peel value desired.G: Specify peel value desired.T: Specify peel value desired.
Call us for recommendations.(734) 464-0700
The speci�cation information listed below correlates to the same box number as shown on the front side. The beginning letter relates to the OEM/Tier 1 as follows: A = ASTM B = Behr C = Chrysler D = Delphi F = Ford G = GM N = Nippondenso T = Toyota V = Visteon W = VolkswagenUse RMA tolerances for die cut cellular products. Spec numbers can be obsoleted or introduced so please email any corrections or requests to [email protected] - Thank You!
Low PermLok Cel
2 lb. X-LinkedPolyethylene
Water ResistantHydro Foam
Seat & HeadrestTopper Foam
Firmer Foams
High DensityFoam
Superseal
Polyether Open Cell Foam
EPDM Reclaimed Rubber
Reclaimed Foam
Polyethylene Soft EPDM Open CellNatural Rubber
Good Tack PSA
Mini-CellPolyethylene
PVN / Vinyl Nitrile
Anti-SqueakFelt
High TackPSA
Mastic Soft PVN /Vinyl Nitrile
P.E.T. Fiber High TempPSA
EVA Foam Neoprene Sponge
Non-WovenPolyester
High Humidity& High Temp PSA
4 lb. HDPE 2A1 SpongeRubber
Poron Direct CoatPSA
PVC 2A2 SpongeRubber
ReticulatedFoam
A PSA to solvethe most
di�cult problem