zurn roof drains

Specification Drainage Engineering Guide

Roof Drains

www.zurn.com

ROOF DRAINS

ZURN INDUSTRIES, LLC SPECIFICATION DRAINAGE OPERATION, 1801 PITTSBURGH AVENUE, ERIE, PA 16502 PHONE 814/455-0921 FAX: 814/454-7929 www.zurn.com

TABLE OF CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

When Selecting A Roof Drain . . . . . . . . . . . . . . . . . . . . . . . . . 1

Pictorial Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Product Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Application Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Sizing Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Zurn Outlet Pipe Connections . . . . . . . . . . . . . . . . . . . . . . . . . 6

Neo-Loc Drain Gasket with Integral Test Cap . . . . . . . . . . . . . 7-8

General Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Options and Variations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Common Roof Drain Accessories . . . . . . . . . . . . . . . . . . . . . . 11

Top-Set® Deck Plate Installation Instructions . . . . . . . . . . . . . 12

Top-Set® Drain Riser Installation Instructions . . . . . . . . . . . . . 12

Typical Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-16

Z101 High Capacity 20" Diameter Main Roof Drain . . . . . . . . 17

Control-Flo Roof Drainage System . . . . . . . . . . . . . . . . . . . . . 18-19

RD2150 Replacement Roof Drain . . . . . . . . . . . . . . . . . . . . . . 20

Materials and Finishes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Product Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-45

ROOF DRAINS


Page 1

INTRODUCTION

All building roofs are subject to destructive effects of sun, rain, snow, seasonal weather changes, ventilation system, exhaust air, ventilationunder the roof, roof loading, traffic on the roof, acid-laden smoke, and the abrasive action of dust and grit borne by high velocity winds.Alternate wetting and drying, freezing and thawing caused by water lying on the roof causes expansion, contraction, and rotting, with damageoften extending even to the substructure.

While sound, comprehensive design and good materials will provide owners with trouble-free roof installation for many years, one certainmeans by which periods between repair and replacement can be importantly extended is through provision of more effective roof drainagesystems. By the simple act of draining water from the roof, many of the major causes of roofing failure can be eliminated.

The Zurn Roof Drains and Drain Accessories represent more than 100 years of experience in supplying engineered roof drainage equipment tothe construction market.

WHEN SELECTING A ROOF DRAIN

Note: First and foremost, be sure to comply with all local plumbing codes.

To select the proper roof drain, the following information must be known:

1. Type of Roof Construction

2. Roof Size

3. Roof Pitch

4. Location of Drains

5. Desired Rate of Drainage

6. Roof Load Requirement

7. Safety Load Requirement

8. Volume of Expected Rainfall(Consult the Inch Per Hour Rainfall map on Page 5.)

ROOF DRAINS


Page 2

Z104Deep Sump Roof DrainLow Silhouette Dome

Z105Control-Flo Roof Drainwith Parabolic Weir

Z10015" Diameter Main Roof Drain

Low Silhouette Dome

Z103-4515" Diameter Deep Sump 45°

Dual Outlet Roof Drain

Z10315" Diameter Deep SumpDual Outlet Roof Drain

Z101High Capacity 20" Diameter

Main Roof DrainLow Silhouette Dome

Z10815" Diameter

Deck Receptor Drain

Z107Wide Deck Flange Roof Drain

Z11112" Diameter Roof Drain

For Metal Decks

Z12112" Diameter Roof DrainLow Silhouette Dome

Z1258" Diameter Roof DrainLow Silhouette Dome

Z12212" Diameter

Deck Receptor Drain

Z1278-1/2" Diameter

Deck Receptor Drain

Z13014 9/32" Diameter Siphonic

Main Roof Drain

Z15014" Prom-Deck Drainwith Heel-Proof Grate

Z13114 9/32" Diameter Siphonic

Overflow Roof Drain

PICTORIAL INDEX

Z150-DT14" Prom-Deck Drainwith Heel-Proof Grate



Z158-DT8" Prom-Deck Drainwith Heel-Proof Grate

ROOF DRAINS


Page 3

PICTORIAL INDEX

Z16412" Diameter Combination

Main Roof and Overflow Drain

Z1804" Diameter Cornice Drain

Bottom Outlet

Z1658-3/8" Diameter Combination Main Roof and Overflow Drain

Z166Vandal Resistant Emergency

Overflow Drain


90° Outlet

Z1895" x 6" x 11" Scupper Drain


90° Outlet

Z1876" x 7" or 8" x 12"

Oblique Scupper Drain

Z190Vertical Expansion Joint

Z193Vandal-Proof Hooded Vent Cap

Z1915" x 4" x 24" Downspout Boot

Z191-RD4" x 18" Downspout Boot

Z16315" Diameter Combination

Main Roof and Overflow Drain

Z160135° Scupper Drain

Z1613" x 10" Oblique Scupper Drain

Z1924" x 3" Downspout Boot


Bottom Outlet

Available through Zurn Light Commercial

Z195Vent Stack Flashing Sleeve

Z196Vent Stack Flashing Sleeve

Z197Riser Sleeve


Page 4

ROOF DRAINS

Z198Parapet Scupper Sleeve

Z199Downspout Nozzle

Z199-DCDownspout Cover

RD2150Replacement Roof Drain

PICTORIAL INDEX

ROOF DRAINS


Page 5

Main Roof Z100, Z100-90, Z104, Z105, Z107, Z108, Z130

High Capacity Z101

Water Insulated Main Roof Z100-AW, Z100-W, Z100-89

Medium Area Z111, Z121, Z121-90, Z122

Inverted Membrane Roof Deck Z100-85, Z100-BS, Z121-85, Z125-85

Overflow Z108, Z122, Z127, Z163, Z164, Z165, Z131

Penthouse and Small Area Z125, Z125-90, Z127

Promenade and Patio Z150, Z154, Z158, Z150-DT, Z154-DT, Z158-DT

Parapet Scupper Z160, Z161, Z187, Z189

Canopy and Terrace Z180, Z181, Z182, Z185

Expansion Joints Z190

Downspout Boot Z191, Z191-RD, Z192

Vent Cap Z193

Flashing Sleeves and Scupper Sleeves Z195, Z196, Z197, Z198

Downspout Nozzle Z199, Z199-DC

Siphonic Roof Drains Z130, Z131

Dual Outlet Roof Drains Z103, Z103-45

APPLICATION INDEX – ZURN HAS A DRAIN FOR ALL APPLICATIONS

Roof drain selection should be made with a specific type of roof con struc tion in mind. The many types and sizes of drains offered by Zurn,coupled with a wide array of available options, provide you with a roof drain for all applications.

APPLICATION RECOMMENDED ROOF DRAIN

Zurn Roof Drains are constructed of high quality materials and, in general, are designed to meet the requirements of ASME Standard A112.6.4(revision and redesignation of ANSI A112.21.2M). For verification of a selected roof drain, contact your local Zurn Sales Representative.

PRODUCT COMPLIANCE


ROOF DRAIN VERTICAL REQUIREMENT FOR HORIZONTALROOF AREAS AT VARIOUS RAINFALL RATES*

Leader Size Hourly Rainfall In Inches

Pipe Open 1 1-1/2 2 2-1/2 3 4 5 6 7 8Size Area

(Inches) (Sq. In.) Total Square Footage Covered Per Drain

2 3.14 2,880 1,920 1,440 1,150 960 720 575 480 410 360

3 7.06 8,880 5,860 4,400 3,520 2,930 2,200 1,760 1,470 1,260 1,100

4 12.56 18,400 12,700 9,200 7,360 6,130 4,600 3,680 3,070 2,630 2,300

5 19.60 34,600 23,050 17,300 13,840 11,530 8,650 6,920 5,765 4,945 4,325

6 28.30 54,000 36,000 27,000 21,600 18,000 13,500 10,800 9,000 7,715 6,750

8 50.25 116,000 77,400 58,000 46,400 38,660 29,000 23,200 19,315 16,570 14,500

Page 6

Step 2: Locate building site on map below to find rainfall rate.Note: This map is taken from the National StandardPlumbing Code, Appendix A, and should only be used forgeneral reference. Consult local codes for more precisedata. Example: For a building located in Erie, PA, the map shows a 4" hourly rainfall.

Step 3: Cross reference leader size with hourly rainfall in chartbelow to obtain roof area that can be handled by eachleader. Example: For a 4" hourly rainfall and 4" leader, each drain can handle 4,600 sq. ft. of roof area.

Step 4: Divide total roof area by area found in Step 3 to obtain thenumber of drains required. Example: 150,000 sq. ft. dividedby the 4,600 sq. ft. equals 32.6, or 33 drains required. Thedrains should be equally spaced and located symmetricallyabout the roof.

SIZING DATA (For Conventional Drainage)

STORM DRAINAGE SIZING PRECIPITATION RATE INCHES/HOUR – BASED ON 15-MINUTE PRECIPITATION

Zurn makes it easy to size roof drains. The four things you will need to know are: 1) rate of precipitation; 2) total area of roof; 3) size ofleader required; and 4) area handled by each drain.

When sizing roof drains, the limiting factor for the amount of watereach drain will carry away is the size of leader. Therefore, increasingleader size decreases the number of drains required.

STEP-BY-STEP SIZING OF ZURN DRAINS

Step 1: A. Calculate total roof area. Example: Roof area is 300 x 500 ft; 300 x 500 =150,000 sq. ft.

B. Determine the size of leader to be used. Example: 4" leader size is selected.

*Above sizing data is offered as a guide only. For actual ap pli ca tions consult local codes.

ROOF DRAINS


Page 7

ZURN OUTLET PIPE CONNECTIONS

INSIDE CAULK (IC)Often specified where drain body is positioned on pipe, bottom ofoutlet is sealed with oakum and connection is then completedaccording to local plumbing codes.

INSIDE GASKET (IG)The IG connections utilize an inside caulk drain body and a Zurn“Sealtrol” gasket. This connection is only recommended forbasement or ground floor applications.

IRON PIPE (IP)Zurn Iron Pipe Threaded connection is an old industry standard. The female (NPT) threaded outlet is often speci fied on industrial and institutional applications.

NO-HUB (NH)The most widely used connection. A No-Hub connection is achievedby butting No-Hub soil pipe or plastic pipe to the bottom of drainand securing it with a NH joint clamp. (Clamp furnished by others.)

NEO-LOC (NL)Zurn Neo-Loc is a unique labor saving compression gasketedconnection designed to simply push on the stub end of the pipe. The Neo-Loc drain body and gasket can be utilized with plastic,steel, No-Hub and service weight soil pipe. A unique pipe stop cast in each Zurn Neo-Loc drain body ensures a proper fit.Note: Not recommended for roof drain applications due to the watertight integrity ofthe Neo-Loc connection to the leader pipe being dependant upon adequate leaderpipe support and accurate perpendicularity of leader pipe into Neo-Loc gasket.

Special Note: Zurn “Neo-Loc” and “Sealtrol” gaskets are designedfor use exclusively with Zurn drainage products. They are not soldseparately and all warranties either expressed or implied would beforfeited if used in other than a Zurn drainage product.

Dimensions in Inches [mm]

OUTLETS 'A' 'B' 'C'2" [51] No-Hub Outlet 2 [51] 2-3/8 [60] 1-1/8 [29]

3" [76] No-Hub Outlet 3 [76] 3-3/8 [86] 1-1/8 [29]

4" [102] No-Hub Outlet 4 [102] 4-3/8 [111] 1-1/8 [29]

5" [127] No-Hub Outlet 4-15/16 [126] 5-5/16 [135] 1-1/2 [38]

6" [152] No-Hub Outlet 5-15/16 [151] 6-5/16 [160] 1-1/2 [38]

8" [203] No-Hub Outlet 7-15/16 [202] 8-3/8 [213] 2 [51]

10" [254] No-Hub Outlet 10 [254] 10-9/16 [268] 2 [51]

12" [305] No-Hub Outlet 12 [305] 12-9/16 [319] 2 [51]

2" [51] Neo-Loc Outlet 2 [51] 3-3/8 [86] 3 [76]

3" [76] Neo-Loc Outlet 3 [76] 4-3/8 [111] 4 [102]

4" [102] Neo-Loc Outlet 4 [102] 5-1/2 [140] 5-1/8 [130]

2" [51] I.C. Outlet 2-5/8 [67] 3-1/16 [78] –

3" [76] I.C. Outlet 3-3/4 [95] 4-3/16 [106] –

4" [102] I.C. Outlet 4-3/4 [121] 5-3/16 [132] –

5" [127] I.C. Outlet 5-3/4 [146] 6-3/16 [157] –

6" [152] I.C. Outlet 6-3/4 [172] 7-3/16 [183] –

8" [203] I.C. Outlet 8-7/8 [226] 9-1/2 [241] –

2" [51] N.P.T. Outlet 2 [51] 9/16 [14] 3-1/4 [83]

3" [76] N.P.T. Outlet 3 [76] 3/4 [19] 4-1/2 [114]

4" [102] N.P.T. Outlet 4 [102] 15/16 [24] 5-5/8 [143]

5" [127] N.P.T. Outlet 5 [127] 15/16 [24] 6-11/16 [170]

6" [152] N.P.T. Outlet 6 [152] 15/16 [24] 7-3/4 [197]

8" [203] N.P.T. Outlet 8 [203] 1-1/8 [29] 9-3/8 [238]

2" [51] NL w/-TC 2 [51] 3-3/8 [86] 3 [76]

3" [76] NL w/-TC 3 [76] 4-3/8 [111] 4 [102]

4" [102] NL w/-TC 4 [102] 5-1/2 [140] 5-1/8 [130]

I.C. with Sealtrol Gasket (IG)Inside Caulk (IC)

I.P. (Threaded/N.P.T.)

No-Hub (NH)

“Neo-Loc” (NL)

ROOF DRAINS

ROOF DRAINS


Page 8

The Zurn Neo-Loc Gasket with Integral Test Cap is a unique pipeconnection designed to secure a drain fixture to the drain line. Thislabor-saving compression gasket is compatible with plastic, steel,no-hub, extra heavy, and service weight cast iron soil pipe. Both theNeo-Loc drain body and compression gasket are designed to simplypush onto the stub end of the pipe. A pipe stop molded into eachdrain body ensures a proper fit.

NEO-LOC DRAIN GASKET with INTEGRAL TEST CAP

Figure 1

It is often required by plumbing codes that drain lines be tested forleakage once installation is complete. This test is typically performedby plugging all openings in the drain line system and applying ahydrostatic pressure charge of not less than 10-ft. head pressure tothe lines for at least 15 minutes prior to inspection. The slightestloss of pressure in the system may indicate a possible leak.

Preparation to perform such testing can be a time-consuming andlabor-intensive process. All drain fixtures must be plugged prior toline pressurization, and unplugged upon test completion. Currentmethods of preparation may involve the use of an inflatable testplug (Figure 1). Each plug is inserted into an opening in the drainline and inflated to block off the line. Once testing is complete, theplugs have to be deflated and removed. This whole process requiresinitial setup and post-test removal of the plugs, costing valuable time.

Figure 2

The Zurn Neo-Loc Gasket with Integral Test Cap eliminates the needfor multiple test plugs and requires no loss of time for setup, prior toline system pressurization. The test cap is already in place when thedrain body is installed, allowing for immediate testing (Figure 2). Thereis no need to carry multiple plugs from one drain fixture to another.

Maximum Operating Pressure - 10 psi.Material conforms to ASTM standard C564.

Benefits of Using the Neo-Loc Gasket with Integral Test Cap• No setup time required. The test cap is already installed along withthe gasketed drain body. There is no need to carry around separatetest plugs and equipment from drain to drain.

• During construction and installation, dirt and debris often fall downinto the drain line, creating possible blockage problems. The testcap portion of the gasket prevents this from occurring prior to linesystem pressurization.

• Ease of removal. The test cap portion is easily removed and discarded,leaving a clean-edged opening for water to flow through the gasketand pipe.

• Individual test plugs may become lost, damaged, and unusableafter some use. The need to replace these plugs is eliminated,saving the contractor and customer money.

Installation of the Gasket1. Make sure that the end of the drain pipe is cut square, is free of

any burrs, and all sharp edges are broken.

2. Lubricate the inner and outer ribs of the gasket and the outsidediameter of the pipe.

3. Fully insert the gasket into the properly sized Neo-Loc drain body.

4. Push the drain body and gasket onto the end of the drain lineuntil the pipe comes to a secure stop.

Pat. No. 6,739,597


Page 9

NEO-LOC DRAIN GASKET with INTEGRAL TEST CAP, continued

Instructions for Removal of the Test CapOnce testing of the drain line system is complete and permissionhas been given to open the lines, the test cap portion of the gasketcan be removed by following these quick, easy steps:

1. Locate the dotted cutting line near the pull handle on the topsurface of the gasket (Figure 3).

2. Using a sharp-bladed utility knife, reach down into the drain bodyand cut into the gasket along the dotted line. It is important tomake sure that the cut is made fully through the two annularshaped rings shown in Figure 4. Failure to cut through theserings can result in tearing of the pull handle during removal ofthe cap.

3. Using a pair of long-handled channel lock pliers, grab the handlefirmly and pull in a radial direction opposite of the cutting line(Figure 3).

4. Continue pulling the handle until the cap portion is completelysevered from the body of the gasket.

5. Figure 5 shows a finished installation of the gasket after testinghas been completed.

Figure 3

Figure 4

Figure 5

ROOF DRAINS

ROOF DRAINS


Page 10

APipe Size B C D E H M U X

15" Diameter Drain Body

2 [51] 12-1/2 [318] 15 [381] 5-1/2 [140] 5-3/4 [146] 7-1/2 [191] 4-1/4 [108] 4-1/2 [114] 6-3/4 [171]

3 [76] 12-1/2 [318] 15 [381] 5-1/2 [140] 5-3/4 [146] 7-1/2 [191] 3-3/4 [95] 4-1/2 [114] 6-3/4 [171]

4 [102] 12-1/2 [318] 15 [381] 5-1/2 [140] 5-3/4 [146] 7-1/2 [191] 3-1/4 [83] 4-1/2 [114] 6-3/4 [171]

5 [127] 12-1/2 [318] 15 [381] 5-7/8 [149] 7-7/8 [200] 7-1/2 [191] 4-3/4 [121] 4-1/2 [114] 6-3/4 [171]

6 [152] 12-1/2 [318] 15 [381] 5-7/8 [149] 7-7/8 [200] 7-1/2 [191] 4-1/4 [108] 4-1/2 [114] 6-3/4 [171]


2 [51] 10 [254] 12 [305] 4-3/4 [121] 5-3/4 [146] 6 [152] 4-1/8 [105] 4-1/4 [108] 5-5/16 [135]

3 [76] 10 [254] 12 [305] 4-3/4 [121] 5-3/4 [146] 6 [152] 3-5/8 [92] 4-1/4 [108] 5-5/16 [135]

4 [102] 10 [254] 12 [305] 4-3/4 [121] 5-3/4 [146] 6 [152] 3-1/8 [79] 4-1/4 [108] 5-5/16 [135]

5 [127] 10 [254] 12 [305] 4-3/4 [121] 6-3/4 [171] 6-1/2 [165] 3-5/8 [92] 4-1/4 [108] 5-5/16 [135]


2 [51] 7-1/2 [191] 8-1/4 [210] 3-1/2 [89] 6 [152] 5-1/4 [133] 4-1/2 [114] 4-1/4 [108] 4-1/4 [108]

3 [76] 7-1/2 [191] 8-1/4 [210] 3-1/2 [89] 6 [152] 5-1/4 [133] 4 [102] 4-1/4 [108] 4-1/4 [108]

4 [102] 7-1/2 [191] 8-1/4 [210] 3-1/2 [89] 6 [152] 5-1/4 [133] 3-3/8 [86] 4-1/4 [108] 4-1/4 [108]

Zurn Roof Drains are comprised of three basic components: a body (sump), a combination membrane flashing clamp/gravel guard, and adome strainer.

Two of Zurn’s most popular roof drains are the Z100-C-EA-R and the Z100-DP-EA pictured below. These illustrate the basic components andseveral popular options: the adjustable extension (-EA), the roof sump receiver (-R), the underdeck clamp (-C), and the roof deck plate (-DP).

GENERAL PRODUCT INFORMATION

SIDE OUTLET (SUFFIX -90)90° outlet drains are available in 8", 12" and 15" di ame ters. Seethe chart below for di men sions on each size.

DIMENSIONAL CHART (Dimensions in Inches/[mm])

Standard Z100 Roof Drain Shown

Z100-C-EA-R

Z100-DP-EA


Page 11

OPTIONS and VARIATIONS

All Zurn roof drain options are specified as a PREFIX and/or SUFFIX letter or number added to the series designation. Below are the availableoptions. Each item in the catalog is listed with its individual prefix and suffix variation. For il lus tra tions of certain products and options, referto the installation drawings shown on the following pages.

PREFIXES

Z Standard Assembly or D.C.C.I. Body and Top ZAB All Bronze Body with Polished TopZA D.C.C.I. Body with Aluminum Dome ZRB D.C.C.I. Body with Plain Bronze TopZB D.C.C.I. Body with Polished Bronze Top ZANB All Nickel Bronze Body with Polished TopZC D.C.C.I. Body with Cast Iron Dome ZARB All Plain Bronze Body and TopZN D.C.C.I. Body with Polished Nickel Bronze Top ZABN All Bronze Body with Polished Nickel Bronze Grate

-GD Galvanized Cast Iron Dome-HD High Dome-MS Mesh Screen on Overflow Pipe-R Roof Sump Receiver

Distributes weight of the drain and securely cradles drain in roof deck.(It is rec om mended for most Z100, Z121, and Z125 installations.)

-RD Round Inlet and Outlet-S Secondary Strainer-SC Secondary Clamping Collar

For use when a flashing clamp is required at the bottom of an extension.Also used to clamp additional flashing at another level.

-SS Stainless Steel Mesh Screen Over DomeUsed to prevent debris or gravel from entering drain. Screen is securelyfastened to dome.

-ST Dome with Solid Top-TC Neo-Loc Test Cap Gasket

2"-4" NL bottom outlet only.-TS Secured Top with Slotted Screws-VP Vandal-Proof Secured Top

Exposed surface secured with vandal-proof screws.-W2 2" Internal Water Dam

Internal water dam for insulated roof.-W3 3" Internal Water Dam

Internal water dam for insulated roof.-W4 4" Internal Water Dam

Internal water dam for insulated roof.-XJ Vertical Expansion Joint

Allows for thermal expansion and contraction in the piping system.(See Z190)

-4 4" High Body (See Z180)-8 8" High Body (See Z180 and Z181)-10 Parabolic Weir for Sloped Roof (See Z105)-20F 2" High Overflow Pipe (See Z103)-45 45° Side Outlet Bod y (Threaded)-84 4" High Type 304 Stainless Steel Perforated Gravel Guard

Stainless steel ballast guard attached to exterior of clamp collar.Prevents debris from entering drain.

-85 4" High Type 304 Stainless Steel Perforated ExtensionStainless steel ballast guard for use with inverted membrane roof system.Can be ordered in various heights to meet insulation re quire ments.

-89 2" High External Water DamNon-adjustable overflow design. Keeps debris away from the domeuntil overflow action begins.

-90 90° Threaded Side Outlet Body (2" thru 6")

-AC Angular Underdeck ClampTwo-piece 19" square fabricated clamp with 1-1/2" raised lip. For in stal la tions where roof thickness does not ac com mo date standardunderdeck clamp.

-AR Acid Resistant Epoxy Coated Finish-AW 3/4" to 4" Adjustable Water Level Regulator

Made of Dura-Coated cast iron it is primarily used for storing wateron the roof structure to insulate the roof.

-BS Bronze Mesh Screen Over DomeOption used to prevent debris or gravel from entering drain. Bronzescreen is securely fastened to dome.

-C Underdeck ClampTwo-piece clamp made of Dura-Coated cast iron secures drain todeck. Sta bi lizes the drain and adds rigidity to the in stal la tion.

-CF Bottom Clamping Flange (See Z195)-DA Downspout Adapter

Typ i cal ly used on scupper drains, this Dura-Coated cast iron option isused as an interface between the drain and the downspout.

-DB Deep Sump Body (See Z104)-DE Deck Extensions (Includes Deck Plate -DP)-DG Duresist Grate

Used in place of regular grate on promenade deck drains whereheavier grate loading is required. Consult the General Ref er enceSection for speci fi ca tions on ductile iron.

-DP Top-Set® Roof Deck PlateReplaces both the -C and -R.

-DR Adjustable Drain Riser AssemblyAdjustment from 3-5/8" to 7-1/4".

-DU Cast Iron Dome on Overflow Pipe (See Z103)-DX Dex-O-Tex Flange

4" wide flange for use with applied latex. Wide flange assures watertight and per ma nent bond.

-E Static ExtensionNon-adjustable extension used to bring drain height up to total deckthickness. Extension height must be specified.

-EA Adjustable Extension AssemblyDura-Coated cast iron, 1-3/4" thru 3-1/2" adjustable extension whichincorporates a unique O-Ring seal to ensure a wa ter tight seal afteradjustment. Can be used with static extension to obtain extension height.

-EB Top-Set® Adjustable Extension Assembly-ES Static Extension with Secondary Clamp Collar at Body

For clamping at roof drain body.-FG Flush Grate

Grate flush with contour of drain body.-FS Flat Strainer-G Galvanized Cast Iron

SUFFIXES

ROOF DRAINS

ROOF DRAINS


Page 12

COMMON ROOF DRAIN ACCESSORIES

While roof applications and designs vary from one building to the next, the purpose of the drain does not. When determining the type of drain,the size of drains, and the total number of drains needed for your particular application, drain accessories are often used for installation purposes.

The patented Zurn Top-Set® Deck Plate (-DP) replaces the roof sump receiver (-R) and underdeck clamp (-C). The Top-Set® Deck Plate providesfor a faster, more durable installation using less parts, all installed from the top of the deck.

-R Roof Sump Receiver (Z100-R Option Shown)-DP Top-Set® Deck Plate (Z100-DP Option Shown)

The roof sump receiver, also referred to as a bearing pan, is usedwhen exact location of the drain can’t be determined or wheninstances of opening the roof can not be precisely cut.

Unless the roof drain is poured directly into the concrete, theUnderdeck Clamp (-C) is recommended to provide a secure, long lasting installation of the roof drain to your roof.

-C Underdeck Clamp (2"-5" Outlet)

-EA Adjustable Extension Assembly -DR Top-Set® Drain Riser

The -EA Adjustable Extension Assembly is very popular and oftenused when working with various degrees of roof insulation.

The -DR Top-Set Drain Riser Assembly is very similar to the -EA;however, the extension portion is completely removed from the path of the waterway.

-C Underdeck Clamp (6"-8" Outlet)


Page 13

TOP-SET® DECK PLATE (-DP) INSTALLATION INSTRUCTIONS

1. Create a square opening in roof (Q-deck) to receive drain assembly.Opening sizes are: Z100 18" x 18"

Z121 15" x 15"Z125 11" x 11"

2. Fasten drain body to deck plate by aligning the four (4) bosses onbody and four (4) slots on plate using bolts provided.

3. Put body/plate assembly onto the precut opening in the roof,aligning deck plate attachment slots in the appropriate position.

4. Fasten the assembly to the roof with self-tapping screws(provided by others).

5. Install insulation (if required) and secure waterproofing membraneto roof drain body with the clamp collar.

6. Attach dome to clamp collar to complete assembly.

Note: Full installation is completed from the top of the roof deck, except forpipe connection.

TOP-SET® DRAIN RISER (-DR) INSTALLATION INSTRUCTIONS

1. Create a square 18" x 18" opening in roof (Q-deck) to receivedrain assembly.

2. Fasten drain riser flange to deck plate by aligning the four (4)threaded holes on the flange and four (4) slots on the deck plateusing 3/8-16 x 1/2 bolts provided.

3. Thread bolts from underside of deck plate, thereby fastening thedeck plate between the bolt head and flange. Flange slots may beused as an alternative with other desired hardware (not included).

4. Fasten the drain body to the drain riser sleeve by aligning the four(4) threaded holes on the body and the four (4) holes on the drainriser using 3/8-16 x 3/4 bolts provided.

5. Put deck plate/flange assembly onto the precut opening in the roof,aligning deck plate attachment slots in the appropriate position.

6. Fasten the assembly to the roof with self-tapping screws(provided by others).

7. Screw on the drain body/drain riser sleeve assembly to deck plate/flange assembly on roof. Adjust to desired height.

8. Install insulation (if required) and secure waterproofing membraneto roof drain body with the clamp collar.

9. Attach dome to clamp collar to complete assembly.

ROOF DRAINS


Page 14

TYPICAL INSTALLATIONS

CONCRETE DECK with LIQUID MEMBRANEZ100-AC-DX

Drain installed in a concrete deck with a mopped Dex-O-Tex finish. Drain is illustrated with an gu larunderdeck clamp (-AC) and 20" diameter Dex-O-Texflange (-DX). The (-AC) option is a Zurn alternate to thestandard underdeck clamp which allows clearancearound the drain body.

THICK CONCRETE DECK with INSULATIONZ100-C-E-EA

Drain installed in an insulated concrete deck. Drain isillustrated with underdeck clamp (-C), static extension (-E) and adjustable extension assembly (-EA). This drainallows over 2" of adjustment for varying insulationthicknesses.

INVERTED ROOF STEEL DECKZ100-AC-BS-R-84

Drain installed in a steel deck with insulated built-uproof. Drain is illustrated with angular underdeck clamp(-AC), bronze mesh screen over dome (-BS), roof sumpreceiver (-R), and gravel guard (-84).

INVERTED ROOF CONCRETE DECKZ100-C-R-XJ-85

Drain installed in an insulated concrete deck. Drain is illustrated with underdeck clamp (-C), roof sumpreceiver (-R), vertical expansion joint (-XJ), and Zurnballast guard extension (-85). The (-XJ) option is alsoavailable in 8" and 12" di ame ter drains. (See Z121 and Z125.)

ROOF DRAINS


Page 15


STEEL DECK WATER INSULATED and/or OVERFLOWZ100-C-E-R-89

Drain installed in a steel deck. Drain is illustrated withunder deck clamp (-C), static extension (-E), roof sumpreceiver (-R), and 2" high external water dam (-89). The (-89) feature is used where a level of water is to bemaintained for insulation purposes or where an overflowdrain is required. The (-89) option is also avail able in 8"and 12" di ame ter drains. (See Z121 and Z125.)

PRECAST CONCRETE DECK with OVERFLOW DRAINAGEZ100-C-W2, -W3, or -W4

Drain installed in a precast concrete deck. Drain isillustrated with underdeck clamp (-C) and 4" internal water dam (-W4). The (-W4) option is used to maintain a 4" water level on the roof for insulation purposes orfor secondary drainage. The water dam is offered in 2" (-W2), 3" (-W3), or 4" (-W4) heights to meet specificapplication requirements.

INSULATED STEEL DECKZ103-45-DP-E

?

15" DIAMETER ADJUSTABLE ROOF DRAIN with DRAIN RISERZ100-DR

Drain installed in a steel deck with insulated roof. Drain isillustrated with the Top-Set® drain riser adjustable roof extension assembly (-DR).

ROOF DRAINS


Page 16

ROOF DRAINS

INSULATED STEEL DECKZ121-DP-E

Drain installed in a steel deck. Drain is illustrated withstatic extension (-E) and Top-Set® roof deck plate (-DP).Deck plate replaces the need for an underdeck clamp (-C) and roof sump receiver (-R).


14" PROM-DECK DRAINZ150-EA-SC-85

Drain installed in an above-grade concrete deck. Drainis illustrated with adjustable extension (-EA), secondaryclamping collar (-SC), and stainless steel ballast guardextension (-85).

15" DIAMETER COMBINATION MAIN ROOF and OVERFLOW DRAINZ163-E

Drain installed in a steel deck with insulated roof. Drain is illustrated with static extension (-E) and double Top-Set® deck plate.

RECEPTOR DRAINZ108-C-E-R-89

Drain installed in a steel deck. Drain is illustrated withunderdeck clamp (-C), static extension (-E), roof sumpreceiver (-R), and a 2" high external water dam (-89),open sump and a small bottom dome strainer. Specifywhere overflow or indirect waste application is required.

ROOF DRAINS


Page 17

SCUPPER DRAIN INSTALLEDZ187-DA

Zurn scupper drain illustrated with regu larly fur nishedclamping collar, oblique grate and optional downspoutadapter (-DA). See Z189 for additional scup per drains.


PROM DECK INSTALLEDZ150-C

Prom deck drain installed in a concrete deck. 14" squaredrain is illustrated with underdeck clamp (-C) and heavy-duty, heel-proof grate. Other Prom Deck drains includethe 11" Z154 and 8" Z158. Both of these drains arefurnished with a light-duty, heel-proof grate.

CORNICE DRAIN INSTALLED – CONCRETE DECKZ180

This 4" di ame ter cornice drain is complete with clampingcollar and available with 1-1/2" or 3" high dome. For adrain with 90° outlet, see Z185.


Page 18


DOWNSPOUT NOZZLEZ199

Overflow drain piping shown inside of building wall andexiting just above ground level.

DOWNSPOUT COVERZ199-DC

Overflow drain piping shown with round stainless steeldownspout cover with perforated hinged strainerinstalled flush with exterior wall.

ROOF DRAINS


Page 19

Z101 HIGH CAPACITY 20" DIAMETER MAIN ROOF DRAIN

Many regions are affected by tropical storms and other weatherphenomenon making it necessary to transport large amounts of runoffwater as fast and efficiently as possible. For these applications, Zurnoffers the Z101 High Capacity Roof Drain. The Z101 High CapacityRoof Drain is over 30 percent larger than standard size roof drains,making it the most efficient flowing roof drain available through themarket, comparing depth of head versus flow rate.

When designing roof drainage systems in regions where a largeamount of water can build up on the roof in a short period of time,extra consideration should be given to roof drain location and outletpipe diameter. The Z101 High Capacity Roof Drain is available in 8-, 10-, and 12-inch outlet sizes. It is common during severe stormsfor water to be blown by wind to one side of the roof area. This couldcreate a situation that exceeds the weight limits of the roof support,resulting in a roof collapse. To avoid this situation, the Z101 HighCapacity Roof Drain should be utilized and located to remove thewater buildup as quickly as possible.

The Z101 High Capacity Roof Drain has been independently lab testedand designed for maximum flow effectiveness, taking into considerationthe design of the drain body, outlet size, clamp collar, and dome strainer.The following table illustrates performance of the Z101 roof drain.

0 500 1000 1500 2000 2500 30000

5

10

15

20

25

Zurn Z101 10" High Capacity Roof Drain

Discharge (GPM)

Wat

er D

epth

Abo

ve D

rain

(inc

hes)

Water DepthDischarge Above Drain(GPM) (Inches)

471 2.8667 3.6817 3.8943 4.11156 6.71335 7.31493 7.31636 6.91768 7.11890 7.42005 8.52114 10.42316 13.02502 15.82675 19.12758 20.02916 21.8

Water Temperature: 40°FTest Facility: St. Anthony Falls LaboratoryTest Date: November 17, 1997

ROOF DRAINS


Page 20

ROOF DRAINS

CONTROL-FLO … Today’s Answer for Areas with Restricted Storm Water Drainage Capacity

WHAT IS “CONTROL-FLO”?Control-Flo is an advanced method of removing rain water off dead-level or sloped roofs. As contrasted with conventional drainage practiceswhich attempt to drain off storm water as quickly as it falls on theroof’s surface, Control-Flo drains the roof at a controlled rate. Excesswater accumulates on the roof under controlled conditions … thendrains off at a lower rate after a storm abates.

The key to economical Control-Flo drainage is the utilization of largeroof areas to temporarily store the maximum amount of water withoutoverloading average roofs or creating excessive draindown time duringperiods of heavy rainfall.

ADVANTAGES OF CONTROL-FLOCuts Drainage Costs Fewer roof drains, smaller diameter piping,smaller sewer sizes, and lower installation costs are possible with a Control-Flo drainage system because roof areas are utilized astemporary storage reservoirs.

Reduces Probability of Storm Damage Lightens load on combinationsewers by reducing rate of drain water from roof tops during severestorms, thereby reducing probability of flooded sewers and consequentback flow into basements and other low areas.

The key to successful Control-Flo drainage is a unique, scientificallydesigned weir containing accurately calibrated notches with sidesformed by parabolic curves which provide flow rates directly propor tionalto the head. Shape and size of notches are based on predeterminedflow rates, and all factors involved in roof drainage to assure permanentregulation of drainage flow rates for specific geographic locationsand rainfall intensities.

ROOF LOADING and RUN-OFF RATESExtensive studies show that stresses due to water load on a slopingroof for any fixed set of conditions are very nearly the same as thoseon a dead-level roof. A sloping roof tends to concentrate more waterin the valleys and increase the water depth at this point. The greaterdepth around the drain leads to a faster run-off rate, particularly afaster early run-off rate. As a result, the total volume of water storedon the roof is less, and the total load on the sloping roof is less. Byusing the same area on the sloping roof as on the dead-level roof theincrease in roof stresses due to increased water depth in the valleysis offset by the decrease in the total load due to less water stored.The net result is the maximum roof stresses are approximately thesame for any single span, rise, and fixed set of conditions. A fixed setof conditions would be the same notch area, the same frequency storm,and the same locality.

DEAD-LEVEL ROOFSA dead-level roof for purposes of applying the Zurn Control-Flo drainageprinciple is one which has been designed for zero slope across itsentire surface.

Plan View

Section View

SLOPED ROOFSA sloped roof is one designed commonly with a shallow slope. TheZurn Control-Flo drainage system can be applied to any slope whichresults in a total rise up to 6 inches … and data can be calculatedfor rises exceeding 6 inches.

The total rise of a roof as calculated for Control-Flo application isdefined as the vertical increase in height in inches, from the low pointor valley of a sloping roof (A) to the top of the sloping section (B).Example: A roof that slopes 1/8" per foot having a 24-foot span wouldhave a rise of 24 x 1/8, or 3".

Plan View

Section View

ROOF DRAINS


Page 21

CONTROL-FLO, continued

CONTROL-FLO INSTALLED – CONCRETE ROOFZ105-C Control-Flo Roof DrainThe Zurn Control-Flo roof drain can be used for almost any type ofroof design or installation where flow rates to the drainage systemmust be accurately controlled. The drain utilizes a unique weir designthat limits the flow through the drain.

1) Available with 1 to 6 inverted parabolic notches.

2) Allows linear relationship between depth of water on roof andflow rate through drain.

3) Stores water on roof with controlled discharge so that drainagesystem and roof structural system will not be over loaded.

4) May allow use of smaller diameter piping.

(For sizing, contact Zurn Engineering Department for details.)

PROPER DRAIN LOCATIONThe following good design practice is recommended for selecting theproper number of Control-Flo drains for a given area. On dead-levelroofs, drains should be located no further than 50 feet from eachedge of the roof to assure good run-off regardless of wind direction.Weir should be flush with roof surface, not recessed. On sloping roofs,drains should be located in the valleys at a distance no greater than50 feet from each end of the valleys. Weir should be flush with thevalley roof surface, not recessed. On large roof areas, drains shouldnot be spaced at a distance greater than 200 feet.

RIGID ROOF DESIGNNormal practice of roof design is based on 30 pounds per square foot,therefore this factor should definitely be kept in mind as a primerequirement for assuring a structurally sound roof. Otherwise, roofdeflection may minimize the advantages of a well-designed roofdrainage system.

Failure to recognize the adverse effects of roof deflection, even withconventional roof drainage, may lead to roof failure. With the conceptof Control-Flo roof drainage, the design condition of deflection is equallyimportant. If severe deflection is permitted, rain water will simply seeklow areas, thus intensifying the degree of deflection. Thus, it is extremelyimportant that flat roofs are designed in accordance with normal loadfactors so that deflection will be slight enough in any way to preventprogressive deflection which could cause water depths to load theroof beyond its design limits.

SCUPPERS and OVERFLOW DRAINSRoofing members and understructures, weakened by seepage androt resulting from improper drainage and roof construction, can giveaway under the weight of rapidly accumulated water during flashstorms. Thus, it is recommended, and often required by buildingcodes, to install scuppers and overflow drains in parapet-type roofs.Properly selected and sized scuppers and overflow drains are vitalto a well-engineered drainage system to prevent excessive loading,erosion, seepage, and rotting.


Page 22

ROOF DRAINS

RD2150 REPLACEMENT ROOF DRAINThe RD2150 is installed inside of an existing drain. The drain is usedwhere re-roofing is done over existing roofing, as well as total roofreplacement renovation applications. The original roof drain need notbe disturbed and the new drain is installed by insertion into the leaderpipe. The neoprene gasket with one-way gripping ribs holds the drainin place. Once installed, the drain is held securely in place and sealedto the pipe, preventing possible leakage. Typical installation shows newinsulation and membrane applied to roof.

Note: Tie-down slots for fasteners are provided in the RD2150 flange.It is recommended these be utilized during construction to hold drainbody firmly in place.

RD2150 REPLACEMENT ROOF DRAIN

RD2150 Replacement Roof Drain

RD2150 TYPICAL INSTALLATION

RD2150-FS Flat Sump Replacement Roof Drain

Note: The RD2150 and RD2150-FS are available through Zurn LightCommercial Operation.

ROOF DRAINS


Page 23

MATERIALS and FINISHES

Zurn Cast Iron conforms to ASTM Specification for Gray Iron CastingsA 48, Class 25. It is produced utilizing the latest equip ment andnewest developed foundry tech niques. Zurn cast iron castings arecharacterized by a high degree of strength, corrosion-resistance,workmanship, and finish.

Zurn Duresist is a ductile iron complying with ASTM Spec i fi ca tion A 536, Grade 60-45-10. Its physical prop er ties make it ideal forgrates and drain components that are subjected to severe and heavyduty service. Its chemi cal characteristics make possible a degree ofcorrosion-resistance far superior to that of cast iron. Zurn Duresistexhibits remarkable stress qual i ties, possessing a yield strength inthe same range as that of cast carbon steel, while its ability to absorbthe shock loading of traffic areas is unequalled, making its use idealfor all areas where extra heavy duty service is a requirement – whetherindoors or outdoors – in chemical and metal proc ess ing plants orother industrial applications.

“Zurn Dura Coat” is a specially formulated paint designed to resistcracking and chipping. Dura Coat is a latex based coating developedto be used with cast iron substrate. Dura-Coat is designed, perASME standards, to protect the product "during normal handling andwarehousing prior to installation."

Zurn Galvanized Cast Iron is a proc ess of applying heavy zinc coatingto a thoroughly cleaned iron casting. This coating contains 95% zinc.Zurn gal va niz ing can be supplied on all cast iron parts. It in creaseslongevity and is recommended wher ever the dis col or a tion caused by oxidation of cast iron is ob jec tion able. Gal va nize should be usedin coastal and industrial areas where cor ro sive atmos phere may be encountered.

Cadmium Plated Cast Iron is a process of applying a heavy cadmiumcoating to a thoroughly cleaned iron cast ing. This coating contains95% cadmium in a cold applied process. Cad mi um plating can besupplied on all cast iron parts. It increases longevity and is recom -mended wherever the discoloration caused by oxidation of cast ironis objectionable.

Zurn Bronze is a semi-red brass conforming to ASTM Spec i fi ca tionfor Copper Alloy Sand Casting B 584, Copper Alloy No. 844. The ex posed surface is normally supplied pos sess ing a satin sheen texturewhich allows it to blend unobtrusively with sur round ing finishes.When the ap pli ca tion requires, Zurn Bronze can be pol ished to ahigh gloss.

Zurn Nickel Bronze is a unique material that is ideally suited totraffic-bearing grates and strainers in finished floor areas. It affordsthe combined advantage of greater strength, better appearance, andlonger service life at the same price as chrome plated brass. Superiorductility and shock resistance are the result of a copper nickel alloy(Copper Alloy 997) having a wearing surface similar in appearanceto satin chrome plate; however, because it does not have a platedsurface it cannot chip, peel, crack, or wear off. It is highly resistantto corrosion; however, the process of oxidation will naturally occurover time with most metals. Methods have been developed to prevent,preserve, and restore metals affected by oxidation.

Chrome Plated Bronze is ideal for installation in walls, gutters, and other areas where a bright decorative finish is desired, and isnot subject to the abrasive action of foot and other traffic. It is notrecom mended for installations where the abrasion will eventuallywear through and cause peel ing. It should always be specified forswimming pool fittings due to its high re sis tance to the halogens(chlorine, etc.), encountered in swimming pool sanitation.

Aluminum supplied is casting grade 319. This is an alloy containingboth silicon and copper. It is a solid cast metal in a pleasing lightgray color. The light weight, coupled with its exceptional strengthand corrosion resistance, makes it ideal for drain components suchas sediment buckets and strainers. When used with acid-resistingporcelain enamel coated drains, the possibility of chipping is minimized.

Zurn Stainless Steel castings are normally produced in Type CF8 (304)which is an 18-8 Austenitic Stainless possessing excellent corrosionre sis tant qualities. For some applications where conditions demand,Type CF8M (316) stainless steel can be supplied. Items formed fromstainless steel sheet and other stainless steel prod ucts are regularlyfurnished in Type 304 with 316 as an optional material.

A.R.C. Acid Resisting Epoxy Coating is a baked-on powder coating,which produces a smooth, hard, high gloss finish. This epoxy basedcoating offers high impact re sis tance and excellent life expectancyin all drainage applications.

A.R.E. Acid Resisting Porcelain Enamel is a substantially vitreous or glassy inorganic coating bonded to metal by fusion at a hightemper ature above 800°F. This coating offers excellent acid, abrasion,and wear resistance. The coating is extremely hard and is the ultimatefor sanitation in drainage applications.

Metal Cast Iron Ductile Iron

Specification Class 25 60-45-10

Tensile Strength (PSI) 25/30,000 60/80,000

Yield Strength (PSI) NIL 45/60,000

Elongation NIL 10% to 25%

Modules of Elasticity 16 x 10 24 x 10

Properties of Basic Ductile Versus Cast Iron


Page 24

ROOF DRAINS

NOTES

ROOF DRAINS


Page 25

*Regularly furnished unless otherwise specified.

A Approx. Dome Pipe Size Wt. Open Area Inches [mm] Lbs. [Kg] Sq. In. [cm2]

2 - 3 - 4 [51-76-102] 26 [12]

5 - 6 [127-152] 27 [12] 103 [664]

8 [203] 28 [13]

Z100 15" [381 mm] DIAMETER MAIN ROOF DRAIN Low Silhouette Dome

OPTIONS

OUTLETS (Specify pipe size in inches and type of outlet.)

OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Inside Caulk . . . . . 2IC, 3IC, 4IC, 5IC, 6IC, 8IC . . . . . . 5-1/4" [133 mm]Threaded . . . . . . . 2IP, 3IP, 4IP, 5IP, 6IP, 8IP . . . . . . . . 3-3/4" [95 mm]No-Hub . . . . . . . . . 2NH, 3NH, 4NH, 5NH, 6NH, 8NH . . . 5-1/4" [133 mm]Neo-Loc . . . . . . . . 2NL, 3NL, 4NL . . . . . . . . . . . . . . . . 4-5/8" [118 mm]

PREFIXES Z D.C.C.I. Body with Poly-Dome*ZA D.C.C.I. Body with 6-3/4" [171 mm] High Aluminum DomeZC D.C.C.I. Body with Cast Iron DomeZRB D.C.C.I. Body with Plain Bronze Dome

SUFFIXES–AC Angular Underdeck Clamp–AR Acid Resistant Epoxy Coated Finish –AW 3/4" [19 mm] to 4" [102 mm] Adjustable Water Level Regulator

(Specify Height) (ZC Only)–BS Bronze Mesh Screen Over Dome –C Underdeck Clamp –DP Top-Set® Roof Deck Plate (Replaces both the -C and -R) –DR Adjustable Drain Riser Extension Assembly

Adjustment from 3-5/8" [92 mm] to 7-1/4" [184 mm]–DX Dex-O-Tex Flange –E Static Extension 1" [25 mm] thru 4" [102 mm] (Specify Height)–EA Adjustable Extension Assembly 1-3/4" [45 mm] thru 3-1/2" [89 mm]

For E and EA Extensions Greater Than 4" [102 mm] (Specify Height)–ES Static Extension with Secondary Clamp Collar at Body

(For clamping at roof drain body.)–FG Flush Grate (Replaces Dome Strainer)–G Galvanized Cast Iron–GD Galvanized Cast Iron Dome (ZC Only) –HD 6-3/4" [171 mm] High Aluminum Dome Strainer

(148 sq. in. [955 cm2] open area)–R Roof Sump Receiver–SC Secondary Clamp Collar–SS Stainless Mesh Screen Over Dome–TC Neo-Loc Test Cap Gasket (2" [51 mm] to 4" [102 mm] NL Bottom

Outlet Only)–VP Vandal-Proof Secured Top–W2 2" [51 mm] Internal Water Dam–W3 3" [76 mm] Internal Water Dam–W4 4" [102 mm] Internal Water Dam–XJ Vertical Expansion Joint (See Z190)–84 Stainless Steel Perforated Gravel Guard (Specify Height)–85 Stainless Steel Perforated Extension (Specify Height)–89 2" [51 mm] High External Water Dam–90 90° Threaded Side Outlet Body (2" [51 mm] thru 6" [152 mm])

ENGINEERING SPECIFICATION: ZURN Z100 15" [381 mm] diameter roof drain, Dura-Coated cast ironbody with combination membrane flashing clamp/gravel guard and low silhouette Poly-Dome.


Page 26

ROOF DRAINS

Z101 HIGH CAPACITY 20" [508 mm] DIAMETER MAIN ROOF DRAIN Low Silhouette Dome

OPTIONS


OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]No Hub . . . . . . . . . . . . . . . 8NH, 10NH, 12NH . . . . . . . 7-5/16" [186 mm]

PREFIXES Z D.C.C.I. Body with Cast Iron Dome*

SUFFIXES–AR Acid Resistant Epoxy Coated Finish–DP Top-Set® Roof Deck Plate (Replaces both the -C and -R)–E Static Extension 1" [25 mm] thru 4" [102 mm] (Specify Height)–G Galvanized Cast Iron–W2 2" [51 mm] Internal Water Dam–W3 3" [76 mm] Internal Water Dam–W4 4" [102 mm] Internal Water Dam–89 2" [51 mm] High External Water Dam


ENGINEERING SPECIFICATION: ZURN Z101 20" [508 mm] diameter roof drain, Dura-Coated cast ironbody with combination membrane flashing clamp/gravel guard and low silhouette cast iron dome.


8 [203] 77 [35]

10 [254] 78 [35] 216 [1393]

12 [305] 79 [36]

ROOF DRAINS


Page 27


ENGINEERING SPECIFICATION: ZURN Z104 15" [381 mm] diameter roof drain, Dura-Coated castiron deep sump body with combination membrane flashing clamp/gravel guard and low silhouettePoly-Dome.

Z104 DEEP SUMP ROOF DRAIN Low Silhouette Dome


3 - 4 [76-102]

6 - 8 [152-203] 46 [21] 103 [664]

OPTIONS


OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Inside Caulk . . . . . . . . . . 3IC, 4IC, 6IC . . . . . . . . . . . . . . 10" [254 mm]No Hub . . . . . . . . . . . . . . 3NH, 4NH, 6NH, 8NH . . . . . . . . . 10" [254 mm]


SUFFIXES–AC Angular Underdeck Clamp–AR Acid Resistant Epoxy Coated Finish–AW 3/4" [19 mm] to 4" [102 mm] Adjustable Water Level Regulator

(Specify Height) (ZC Only)–BS Bronze Mesh Screen Over Dome–C Underdeck Clamp–DX Dex-O-Tex Flange –E Static Extension 1" [25 mm] thru 4" [102 mm] (Specify Height)–EA Adjustable Extension Assembly 1-3/4" [45 mm] thru 3-1/2" [89 mm]

For E and EA Extensions Greater Than 4" [102 mm] (Specify Height)–ES Static Extension with Secondary Clamp Collar at Body

(For clamping at roof drain body.)–FG Flush Grate (Replaces Dome Strainer)–G Galvanized Cast Iron–GD Galvanized Cast Iron Dome (ZC Only)–HD 6-3/4" [171 mm] High Aluminum Dome Strainer

(148 sq. in. [955 cm2] open area)–R Roof Sump Receiver–SC Secondary Clamp Collar–SS Stainless Mesh Screen Over Dome–VP Vandal-Proof Secured Top–W2 2" [51 mm] Internal Water Dam–W3 3" [76 mm] Internal Water Dam–W4 4" [102 mm] Internal Water Dam–XJ Vertical Expansion Joint (See Z190)–84 Stainless Steel Perforated Gravel Guard

For Each Additional 1" [25 mm] above 4" [102 mm] (Specify Height)–85 Stainless Steel Perforated Extension

For Each Additional 1" [25 mm] above 4" [102 mm] (Specify Height)–89 2" [51 mm] High External Water Dam


Page 28

ROOF DRAINS


ENGINEERING SPECIFICATION: ZURN Z105 15" [381 mm] diameter Control-Flo Roof Drain fordead-level roof construction, Dura-Coated cast iron body. Control-Flo weir shall be linear functioningwith integral membrane flashing clamp/gravel guard and Poly-Dome. All data shall be verifiedproportional to flow rates.

Z105 CONTROL-FLO ROOF DRAIN with Parabolic Weir

ZURN Z105-C-EA-R Control-Flo roof drain for dead-level roof construction. Drain is as specifiedabove, with Dura-Coated steel roof sump receiver (-R), Dura-Coated cast iron underdeck clamp (-C),and Dura-Coated cast iron adjustable extension and clamp ring with neoprene O-Ring seal (-EA).

Z105-C-EA-R Illustrated


OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Inside Caulk . . . . . . . . . . . . 2IC, 3IC, 4IC . . . . . . . . . . 5-1/4" [133 mm]Threaded . . . . . . . . . . . . . . 2IP, 3IP, 4IP . . . . . . . . . . . 3-3/4" [95 mm]No-Hub . . . . . . . . . . . . . . . . 2NH, 3NH, 4NH . . . . . . . . . 5-1/4" [133 mm]Neo-Loc . . . . . . . . . . . . . . . 2NL, 3NL, 4NL . . . . . . . . . 4-5/8" [118 mm]

SUFFIXES–C Underdeck Clamp–DP Top-Set® Roof Deck Plate (Replaces both the -C and -R)–DR Adjustable Drain Riser Extension Assembly

Adjustment from 3-5/8" [92 mm] to 7-1/4" [184 mm]–E Static Extension 1" [25 mm] thru 4" [102 mm] (Specify Height)–EA Adjustable Extension Assembly 1-3/4" [45 mm] thru 3-1/2" [89 mm]

For E and EA Extensions Greater Than 4" [102 mm] (Specify Height)–G Galvanized Cast Iron–R Roof Sump Receiver–SC Secondary Clamp Collar–TC Neo-Loc Test Cap Gasket (2" [51 mm] to 4" [102 mm] NL Bottom

Outlet Only)–VP Vandal-Proof Secured Top–XJ Vertical Expansion Joint (See Z190) –10 6" [152 mm] High Parabolic Weir for Sloped Roof–90 90° Threaded Side Outlet Body (2" [51 mm] thru 4" [102 mm])


A Approx. Dome Pipe Size Wt. Open Area Inches [mm] Lbs. [Kg] Sq. In. [cm2 ]

2 - 3 - 4 [51-76-102] 34 [16] 103 [664]

OPTIONS

ROOF DRAINS


Page 29


Z107 20" [508 mm] WIDE DECK FLANGE ROOF DRAIN

ENGINEERING SPECIFICATION: ZURN Z107 20" [508 mm] diameter Wide Deck Flange Roof Drain,Dura-Coated cast iron body with combination membrane flashing clamp/gravel guard and lowsilhouette Poly-Dome.

ZURN Z107-C-85 20" [508 mm] diameter wide deck flange roof drain, as specified above, withperforated extension with flat clamp collar (-85), and Dura-Coated cast iron underdeck clamp (-C).

Z107-C-85 Illustrated


OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Inside Caulk . . . . . . . . . . 3IC, 4IC, 6IC . . . . . . . . . . . . 5-1/4" [133 mm]No-Hub . . . . . . . . . . . . . . 3NH, 4NH, 6NH, 8NH . . . . . . . 5-1/4" [133 mm]


SUFFIXES–AC Angular Underdeck Clamp–AR Acid Resistant Epoxy Coated Finish–AW 3/4" [19 mm] to 4" [102 mm] Adjustable Water Level Regulator

(Specify Height)–BS Bronze Mesh Screen Over Dome–C Underdeck Clamp–E Static Extension 1" [25 mm] thru 4" [102 mm] (Specify Height)–EA Adjustable Extension Assembly 1-3/4" [45 mm] thru 3-1/2" [89 mm]

For E and EA Extensions Greater Than 4" [102 mm] (Specify Height)–FG Flush Grate (Replaces Dome Strainer)–G Galvanized Cast Iron–GD Galvanized Cast Iron Dome–HD 6-3/4" [171 mm] High Aluminum Dome Strainer

(148 sq. in. [955 cm2] open area)–SS Stainless Mesh Screen Over Dome–VP Vandal-Proof Secured Top–W2 2" [51 mm] Internal Water Dam–W3 3" [76 mm] Internal Water Dam–W4 4" [102 mm] Internal Water Dam–XJ Vertical Expansion Joint (See Z190) –84 Stainless Steel Perforated Gravel Guard

For Each Additional 1" [25 mm] above 4" [102 mm] (Specify Height)–85 Stainless Steel Perforated Extension

For Each Additional 1" [25 mm] above 4" [102 mm] (Specify Height)–89 2" [51 mm] High External Water Dam

OPTIONS


3 - 4 [76-102]

6 - 8 [152-203] 39 [18] 103 [664]


Page 30

ROOF DRAINS


3 - 4 [76-102] 22 [10] 78 [503]

6 [152] 24 [11]


OPTIONS

Z108 15" [381 mm] DIAMETER DECK RECEPTOR DRAIN


OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Inside Caulk . . . . . 2IC, 3IC, 4IC, 5IC, 6IC, 8IC . . . . . . . 5-1/4" [133 mm]Threaded . . . . . . . 2IP, 3IP, 4IP, 5IP, 6IP, 8IP . . . . . . . . 3-3/4" [95 mm]No-Hub . . . . . . . . 2NH, 3NH, 4NH, 5NH, 6NH, 8NH . . . . 5-1/4" [133 mm]Neo-Loc . . . . . . . . 2NL, 3NL, 4NL . . . . . . . . . . . . . . . . 4-5/8" [118 mm]

Z111 12" [305 mm] DIAMETER ROOF DRAIN For Metal Decks

ENGINEERING SPECIFICATION: ZURN Z111 12" [305 mm] diameter Flat Deck Roof Drain for metaldecks, Dura-Coated cast iron body with combination membrane flashing clamp/gravel guard andlow silhouette cast iron dome.

PREFIXES Z D.C.C.I. Body with Collar*

SUFFIXES–AR Acid Resistant Epoxy Coated Finish–C Underdeck Clamp–DB Deep Sump Body–DP Top-Set® Roof Deck Plate (Replaces both the -C and -R)–DR Adjustable Drain Riser Extension Assembly

Adjustment from 3-5/8" [92 mm] to 7-1/4" [184 mm]–DX Dex-O-Tex Flange–E Static Extension 1" [25 mm] thru 4" [102 mm] (Specify Height)–EA Adjustable Extension Assembly 1-3/4" [45 mm] thru 3-1/2" [89 mm]

For E and EA Extensions Greater Than 4" [102 mm] (Specify Height)–FG Flush Grate–G Galvanized Cast Iron–HD High Dome–R Roof Sump Receiver–TC Neo-Loc Test Cap Gasket (2" [51 mm] to 4" [102 mm] NL Bottom

Outlet Only)–90 90° Threaded Side Outlet Body (2" [51 mm] thru 6" [152 mm])

(See Z1043)

ENGINEERING SPECIFICATION: ZURN Z108 15" [381 mm] diameter Deck Receptor Drain, Dura-Coated cast iron body with combination membrane flashing clamp/deck receptor frame and internalbottom dome strainer.


OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Threaded . . . . . . . . . . . . . . . . 3IP, 4IP . . . . . . . . . . . . . . 1-5/8" [41 mm]

6IP . . . . . . . . . . . . . . . . . . 1-7/8" [48 mm]

PREFIXES Z D.C.C.I. Body with Dome*ZRB D.C.C.I. Body with Plain Bronze Dome

SUFFIXES–BS Bronze Mesh Screen Over Dome–C Underdeck Clamp–FG Flush Grate (Z Only)–G Galvanized Cast Iron–R Roof Sump Receiver–SS Stainless Mesh Screen Over Dome–VP Vandal-Proof Secured Top–XJ Vertical Expansion Joint (See Z190)

A Approx. Pipe Size Wt. Inches [mm] Lbs. [Kg]

2 - 3 - 4 [51-76-102] 41 [19]

5 - 6 [127-152] 39 [18]

8 [203] 42 [19]

OPTIONS

ROOF DRAINS


Page 31


2 - 3 - 4 - 6 22 [10] 78 [503] [51-76-102-152]


OPTIONS

Z121 12" [305 mm] DIAMETER ROOF DRAIN Low Silhouette Dome

ENGINEERING SPECIFICATION: ZURN Z121 12" [305 mm] diameter roof drain, Dura-Coated cast ironbody with combination membrane flashing clamp/gravel guard and low silhouette cast iron dome.

SUFFIXES–AR Acid Resistant Epoxy Coated Finish–BS Bronze Mesh Screen Over Dome–C Underdeck Clamp–DP Top-Set® Roof Deck Plate (Replaces both the -C and -R) –DR Adjustable Drain Riser Extension Assembly

Adjustment from 3-5/8" [92 mm] to 7-1/4" [184 mm]–E 2" [51 mm] High Static Extension (Specify Height)–ES Static Extension with Secondary Clamp Collar at Body (For clamping at roof drain body.)–FG Flush Grate–G Galvanized Cast Iron–R Roof Sump Receiver–SC Secondary Clamp Collar–SS Stainless Mesh Screen Over Dome–TC Neo-Loc Test Cap Gasket (2" [51 mm] to 4" [102 mm] NL Bottom

Outlet Only)–VP Vandal-Proof Secured Top–XJ Vertical Expansion Joint (See Z190) –84 Stainless Steel Perforated Gravel Guard–85 Stainless Steel Perforated Extension–89 2" [51 mm] High External Water Dam–90 90° Threaded Side Outlet Body (2" [51 mm] thru 4" [102 mm])

(Previously Z124)


OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Inside Caulk . . . . . . . . . . 2IC, 3IC, 4IC, 6IC . . . . . . . . . 5-1/4" [133 mm]Threaded . . . . . . . . . . . . 2IP, 3IP, 4IP, 6IP . . . . . . . . . . . 3-3/4" [95 mm]No-Hub . . . . . . . . . . . . . 2NH, 3NH, 4NH, 6NH . . . . . . . 5-1/4" [133 mm]Neo-Loc . . . . . . . . . . . . . 2NL, 3NL, 4NL . . . . . . . . . . . . 4-5/8" [118 mm]

PREFIXES Z D.C.C.I. Body with Dome*ZA D.C.C.I. Body with Aluminum DomeZRB D.C.C.I. Body with Plain Bronze Dome


Page 32

ROOF DRAINS


ENGINEERING SPECIFICATION: ZURN Z122 12" [305 mm] diameter Deck Receptor Drain, Dura-Coated cast iron body with combination membrane flashing clamp/deck receptor frame and internaldome strainer.


2 - 3 - 4 - 6 [51-76-102-152] 29 [13]

Z122 12" [305 mm] DIAMETER DECK RECEPTOR DRAIN


OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Inside Caulk . . . . . . . . . . 2IC, 3IC, 4IC, 6IC . . . . . . . . . 5-1/4" [133 mm]Threaded . . . . . . . . . . . . 2IP, 3IP, 4IP, 6IP . . . . . . . . . . 3-3/4" [95 mm]No-Hub . . . . . . . . . . . . . 2NH, 3NH, 4NH, 6NH . . . . . . . 5-1/4" [133 mm]Neo-Loc . . . . . . . . . . . . . 2NL, 3NL, 4NL . . . . . . . . . . . 4-5/8" [118 mm]

SUFFIXES–AR Acid Resistant Epoxy Coated Finish–C Underdeck Clamp–DP Top-Set® Roof Deck Plate (Replaces both the -C and -R) –E 2" [51 mm] High Static Extension (Specify Height)–G Galvanized Cast Iron–HD High Dome–R Roof Sump Receiver–TC Neo-Loc Test Cap Gasket (2" [51 mm] to 4" [102 mm] NL Bottom


(See Z1043)


OPTIONS

ROOF DRAINS


Page 33


ENGINEERING SPECIFICATION: ZURN Z125 8" [203 mm] diameter roof drain, Dura-Coated cast ironbody with combination flashing clamp/gravel guard and low silhouette cast iron dome.

Z125 8" [203 mm] DIAMETER ROOF DRAIN Low Silhouette Dome

OUTLETS (Specify pipe size in inches and type of outlet.) OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Inside Caulk . . . . . . . . . . . . 2IC, 3IC, 4IC . . . . . . . . . . . 3-7/8" [98 mm]Threaded . . . . . . . . . . . . . . 2IP, 3IP, 4IP . . . . . . . . . . . . 2-5/8" [67 mm]No-Hub . . . . . . . . . . . . . . . . 2NH, 3NH, 4NH . . . . . . . . . . 3-7/8" [98 mm]Neo-Loc . . . . . . . . . . . . . . . 2NL, 3NL, 4NL . . . . . . . . . . 3-3/4" [95 mm]


SUFFIXES–AR Acid Resistant Epoxy Coated Finish–BS Bronze Mesh Screen Over Dome–C Underdeck Clamp–DP Top-Set® Roof Deck Plate (Replaces both the -C and -R) –DR Adjustable Drain Riser Extension Assembly

Adjustment from 3-5/8" [92 mm] to 7-1/4" [184 mm]–E 2" [51 mm] High Static Extension (Specify Height)–ES Static Extension with Secondary Clamp Collar at Body (For clamping at roof drain body.)–G Galvanized Cast Iron–R Roof Sump Receiver–SC Secondary Clamp Collar–SS Stainless Mesh Screen Over Dome–TC Neo-Loc Test Cap Gasket (2" [51 mm] to 4" [102 mm] NL Bottom

Outlet Only)–VP Vandal-Proof Secured Top–XJ Vertical Expansion Joint (See Z190)–84 Stainless Steel Perforated Gravel Guard–85 Stainless Steel Perforated Extension–89 2" [51 mm] High External Water Dam–90 90° Threaded Side Outlet Body (2" [51 mm] thru 4" [102 mm])

(Previously Z126)

OPTIONS


2 - 3 - 4 [51-76-102] 14 [6] 43 [277]

ENGINEERING SPECIFICATION: ZURN Z127 8-1/2" [216 mm] diameter Deck Receptor Drain, Dura-Coated cast iron body with combination membrane flashing clamp/deck receptor frame and internaldome strainer.

Z127 8-1/2" [216 mm] DIAMETER DECK RECEPTOR DRAIN


OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Inside Caulk . . . . . . . . . . . . 2IC, 3IC, 4IC . . . . . . . . . . . . 3-7/8" [98 mm]Threaded . . . . . . . . . . . . . . 2IP, 3IP, 4IP . . . . . . . . . . . . 2-5/8" [67 mm]No-Hub . . . . . . . . . . . . . . . 2NH, 3NH, 4NH . . . . . . . . . . 3-7/8" [98 mm]Neo-Loc . . . . . . . . . . . . . . . 2NL, 3NL, 4NL . . . . . . . . . . 3-3/4" [95 mm]

SUFFIXES–AR Acid Resistant Epoxy Coated Finish–C Underdeck Clamp–DP Top-Set® Roof Deck Plate (Replaces both the -C and -R) –E 2" [51 mm] High Static Extension (Specify Height)–G Galvanized Cast Iron–HD High Dome–R Roof Sump Receiver–TC Neo-Loc Test Cap Gasket (2" [51 mm] to 4" [102 mm] NL Bottom


(See Z1043)


OPTIONS


2 - 3 - 4 [51-76-102] 19 [9]


Page 34

ROOF DRAINS



A D E M

2 [51] 4-1/4 [108]

3 [76] 5-1/2 [140] 5-3/4 [146] 3-3/4 [95]

4 [102] 3-1/4 [83]

5 [127] 5-7/8 [149] 7-7/8 [200]

4-3/4 [121]

6 [152] 4-1/4 [108]

A Approx. Grate Pipe Size Wt. Open Area Inches [mm] Lbs. [Kg] Sq. In. [cm2]

2 - 3 - 4 [51-76-102]

5 - 6 [127-152] 53 [24]

44 [284]

8 [203] 54 [25]

OPTIONS

Z150 14" [356 mm] PROM-DECK DRAIN with Heel-Proof Grate

ENGINEERING SPECIFICATION: ZURN Z150 14" [356 mm] Square Top Prom-Deck Drain, Dura-Coated cast iron body with square promenade frame and heavy-duty, heel-proof grate withcombination membrane flashing clamp/gravel guard.


OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Inside Caulk . . . . . 2IC, 3IC, 4IC, 5IC, 6IC, 8IC . . . . . . . 5-1/4" [133 mm]Threaded . . . . . . . 2IP, 3IP, 4IP, 5IP, 6IP, 8IP . . . . . . . . 3-3/4" [95 mm]No-Hub . . . . . . . . 2NH, 3NH, 4NH, 5NH, 6NH, 8NH . . . . 5-1/4" [133 mm]Neo-Loc . . . . . . . . 2NL, 3NL, 4NL . . . . . . . . . . . . . . . . . 4-5/8" [118 mm]

PREFIXES Z D.C.C.I. Body with Top*ZB D.C.C.I. Body with Polished Bronze Top+ZN D.C.C.I. Body with Polished Nickel Bronze Top+

+Add 3/16" [5 mm] to 2" [51 mm] dimension and 3/8" [10 mm] to 14" [356 mm] dimension.

SUFFIXES–AR Acid Resistant Epoxy Coated Finish–C Underdeck Clamp–DB Deep Sump Body–DG Duresist Grate–DP Top-Set® Roof Deck Plate (Replaces both the -C and -R)–DR Adjustable Drain Riser Extension Assembly

Adjustment from 3-5/8" [92 mm] to 7-1/4" [184 mm]–DX Dex-O-Tex Flange–E Static Extension 1" [25 mm] thru 4" [102 mm] (Specify Height)–EA Adjustable Extension Assembly 1-3/4" [45 mm] thru 3-1/2" [89 mm]

For E and EA Extensions Greater Than 4" [102 mm] (Specify Height)–ES Static Extension with Secondary Clamp Collar at Body (For clamping at roof drain body.)–G Galvanized Cast Iron–R Roof Sump Receiver–S Secondary Strainer–SC Secondary Clamp Collar–TC Neo-Loc Test Cap Gasket (2" [51 mm] to 4" [102 mm] NL Bottom

Outlet Only)–TS Top Secured with Slotted Screws–VP Vandal-Proof Secured Top–XJ Vertical Expansion Joint (See Z190)–Y Sediment Bucket–85 Stainless Steel Perforated Extension–90 90° Threaded Side Outlet Body (2" [51 mm] thru 6" [152 mm])

(Previously Z153)Z150-85-90 Illustrated

ZURN Z150-85-90 14" [356 mm] Square Top Prom-Deck Drain, as specified above, with perforatedextension with flat clamp collar (-85), and 90° side outlet body (-90).

ROOF DRAINS


Page 35


OPTIONS


ENGINEERING SPECIFICATION: ZURN Z154 11" [279 mm] Square Top Prom-Deck Drain, Dura-Coated cast iron body with square promenade frame and heel-proof grate with combination membraneflashing clamp/gravel guard.


OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Inside Caulk . . . . . . . . 2IC, 3IC, 4IC, 5IC, 6IC . . . . . . 5-1/4" [133 mm]Threaded . . . . . . . . . . . 2IP, 3IP, 4IP, 5IP, 6IP . . . . . . . . 3-3/4" [95 mm]No-Hub . . . . . . . . . . . . 2NH, 3NH, 4NH, 5NH, 6NH . . . 5-1/4" [133 mm]Neo-Loc . . . . . . . . . . . 2NL, 3NL, 4NL . . . . . . . . . . . . 4-5/8" [118 mm]

PREFIXES Z D.C.C.I. Body with Top*ZB D.C.C.I. Body with Polished Bronze TopZN D.C.C.I. Body with Polished Nickel Bronze Top

ZURN Z154-C-E-R 11" [279 mm] Square Top Prom-Deck Drain, as specified above, with Dura-Coated cast iron extension (-E), Dura-Coated steel roof sump receiver (-R), and Dura-Coated castiron underdeck clamp (-C).

Z154-C-E-R Illustrated

SUFFIXES–AR Acid Resistant Epoxy Coated Finish–C Underdeck Clamp–DG Duresist Grate (Z Only)–DP Top-Set® Roof Deck Plate (Replaces both the -C and -R) –E 2" [51 mm] High Static Extension (Specify Height)–ES Static Extension with Secondary Clamp Collar at Body (For clamping at roof drain body.)–G Galvanized Cast Iron–R Roof Sump Receiver–S Secondary Strainer–SC Secondary Clamp Collar–TC Neo-Loc Test Cap Gasket (2" [51 mm] to 4" [102 mm] NL Bottom

Outlet Only)–TS Top Secured with Slotted Screws–VP Vandal-Proof Secured Top–XJ Vertical Expansion Joint (See Z190) –Y Sediment Bucket–85 Stainless Steel Perforated Extension–90 90° Threaded Side Outlet Body (2" [51 mm] thru 4" [102 mm])

A Approx. Grate Pipe Size Wt. Open Area Inches [mm] Lbs. [Kg] Sq. In. [cm2 ]

2 - 3 - 4 - 5 - 6 29 [13] 20 [129] [51-76-102-127-152]


Page 36

ROOF DRAINS

OPTIONS


ENGINEERING SPECIFICATION: ZURN Z158 8" [203 mm] Square Top Prom-Deck Drain, Dura-Coated cast iron body with square promenade frame and heel-proof grate with combinationmembrane flashing clamp/gravel guard.

OUTLETS (Specify pipe size in inches and type of outlet.) OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Inside Caulk . . . . . . . . . . . . . 2IC, 3IC, 4IC . . . . . . . . . . 3-7/8" [98 mm]Threaded . . . . . . . . . . . . . . . 2IP, 3IP, 4IP . . . . . . . . . . . . 2-5/8" [67 mm]No-Hub . . . . . . . . . . . . . . . . 2NH, 3NH, 4NH . . . . . . . . . 3-7/8" [98 mm]Neo-Loc . . . . . . . . . . . . . . . 2NL, 3NL, 4NL . . . . . . . . . 3-3/4" [95 mm]

PREFIXES Z D.C.C.I. Body with Top*ZB D.C.C.I. Body with Polished Bronze TopZN D.C.C.I. Body with Polished Nickel Bronze Top

SUFFIXES–AR Acid Resistant Epoxy Coated Finish–C Underdeck Clamp–DG Duresist Grate (Z Only)–DP Top-Set® Roof Deck Plate (Replaces both the -C and -R) –E 2" [51 mm] High Static Extension (Specify Height)–ES Static Extension with Secondary Clamp Collar at Body (For clamping at roof drain body.)–G Galvanized Cast Iron–R Roof Sump Receiver–S Secondary Strainer–SC Secondary Clamp Collar–TC Neo-Loc Test Cap Gasket (2" [51 mm] to 4" [102 mm] NL Bottom

Outlet Only)–TS Top Secured with Slotted Screws–VP Vandal-Proof Secured Top–XJ Vertical Expansion Joint (See Z190) –Y Sediment Bucket–85 Stainless Steel Perforated Extension–90 90° Threaded Side Outlet Body (2" [51 mm] thru 4" 102 mm])

(Previously Z159)Z160 135° SCUPPER DRAIN

ENGINEERING SPECIFICATION: ZURN ZRB160 135° Scupper Drain, Dura-Coated cast iron body,plain bronze grate with integral membrane clamp.


OUTLET 'E'OUTLET DESIGNATION BODY HT.TYPE Pipe Size/Outlet Type DIM.Threaded . . . . . . . . . . . . 2IP, 3IP, 4IP, 5IP, 6IP . . . . . . . . . . . . See Chart

PREFIXES ZRB D.C.C.I. Body with Plain Bronze Grate*ZB D.C.C.I. Body with Polished Bronze GrateZN D.C.C.I. Body with Polished Nickel Bronze Grate

SUFFIXES–DA Downspout Adapter 2" [51 mm], 3" [76 mm], 4" [102 mm],

6" [152 mm]–G Galvanized Cast Iron

OPTIONS


2 - 3 - 4 [51-76-102] 18 [8] 11 [71]

Dimensions in Inches [mm] Approx. Grate A Wt. Open Area Pipe Size B Lbs. [Kg] Sq. In. [cm2 ]

2 [51] 1-5/8 [41] 3 [76] 2-3/16 [56] 4 [102] 2-11/16 [68] 52 [24] 114 [735] 5 [127] 3-1/4 [83] 6 [152] 3-3/4 [95]


ROOF DRAINS


Page 37


SUFFIXES–DA Downspout Adapter–45 45° Side Outlet Body

OPTIONS

ENGINEERING SPECIFICATION: ZURN ZARB161 3" x 10" [76 mm x 254 mm] Oblique ScupperDrain, plain bronze body with gasket, plain bronze grate with integral membrane clamp.

Z161 3" x 10" [76 mm x 254 mm] OBLIQUE SCUPPER DRAIN


OUTLET 'E'OUTLET DESIGNATION BODY HT.TYPE Pipe Size/Outlet Type DIM.Threaded . . . . . . . . . . . . . . . . . . 2IP, 3IP . . . . . . . . . . . . . . . . See Chart

PREFIXES ZARB All Bronze Body with Plain Bronze Grate*ZAB All Bronze Body with Polished Bronze GrateZABN All Bronze Body with Polished Nickel Bronze Grate

A Approx. GratePipe Size Wt. Open Area

Inches [mm] Lbs. [Kg] Sq. In. [cm2]

2 - 3 [51-76] 21 [10] 19 [123]

Z163 15" [381 mm] DIAMETER COMBINATION MAIN ROOF and OVERFLOW DRAINwith Low Silhouette Domes and Double Top-Set® Deck Plate

A Approx. DomePipe Size Wt. Open Area

Inches [mm] Lbs. [Kg] Sq. In. [cm2 ]

2 - 3 - 4 [51-76-102] 36 [16]

5 - 6 [127-152] 37 [17] 103 [664]

8 [203] 38 [17]

ENGINEERING SPECIFICATION: ZURN Z163 15" [381 mm] diameter roof drain and overflow drain.Dura-Coated cast iron bodies with combination membrane flashing clamp/gravel guards, double Top-Set® deck plate, and low silhouette Poly-Domes.

OUTLETS (Specify pipe size in inches and type of outlet.) OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Inside Caulk . . . . . . 2IC, 3IC, 4IC, 5IC, 6IC, 8IC . . . . . 5-1/4" [133 mm]Threaded . . . . . . . . 2IP, 3IP, 4IP, 5IP, 6IP, 8IP . . . . . . . 3-3/4" [95 mm]No-Hub . . . . . . . . . 2NH, 3NH, 4NH, 5NH, 6NH, 8NH . . . 5-1/4" [133 mm]Neo-Loc . . . . . . . . . 2NL, 3NL, 4NL . . . . . . . . . . . . . . . 4-5/8" [118 mm]


SUFFIXES–AR Acid Resistant Epoxy Coated Finish–AW 3/4" [19 mm] to 4" [102 mm] Adjustable Water Level Regulator–BS Bronze Mesh Screen Over Dome–DR Top-Set® Drain Riser–E Static Extension 1" [25 mm] thru 4" [102 mm] (Specify Height)–EA Adjustable Extension Assembly 1-3/4" [45 mm] thru 3-1/2" [89 mm]–ES Static Extension with Secondary Clamp Collar–G Galvanized Cast Iron–GD Galvanized Cast Iron Dome–SC Secondary Clamping Collar–SS Stainless Steel Mesh Screen Over Dome–TC Neo-Loc Test Cap Gasket (2" [51 mm] to 4" [102 mm] NL Bottom

Outlet Only)–VP Vandal-Proof Secured Top–W3 3" [76 mm] Internal Water Dam–W4 4" [102 mm] Internal Water Dam–XJ Vertical Expansion Joint (See Z190) –84 Stainless Steel Perforated Gravel Guard–85 Stainless Steel Perforated Extension–89 2" [51 mm] High External Water Dam (Replaces Internal Dam)

OPTIONS


Page 38

ROOF DRAINS


Z164 12" [305 mm] DIAMETER COMBINATION MAIN ROOF and OVERFLOW DRAINwith Low Silhouette Domes and Double Top-Set® Deck Plate


2 - 3 - 4 - 5 - 6 31 [14] 78 [503] [51-76-102-127-152]

ENGINEERING SPECIFICATION: ZURN Z164 12" [305 mm] diameter roof drain and overflow drain.Dura-Coated cast iron bodies with combination membrane flashing clamp/gravel guards, double Top-Set® deck plate, and low silhouette cast iron domes.


OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Inside Caulk . . . . . . . . . . . 2IC, 3IC, 4IC, 6IC . . . . . . . . 5-1/4" [133 mm]Threaded . . . . . . . . . . . . . 2IP, 3IP, 4IP, 6IP . . . . . . . . . 3-3/4" [95 mm]No-Hub . . . . . . . . . . . . . . 2NH, 3NH, 4NH, 6NH . . . . . . 5-1/4" [133 mm]Neo-Loc . . . . . . . . . . . . . . 2NL, 3NL, 4NL . . . . . . . . . . . 4-5/8" [118 mm]


SUFFIXES–AR Acid Resistant Epoxy Coated Finish–BS Bronze Mesh Screen Over Dome–E Static Extension 1" [25 mm] thru 4" [102 mm] (Specify Height)–ES Static Extension with Secondary Clamp Collar at Body

(For clamping at roof drain body.)–G Galvanized Cast Iron–SC Secondary Clamping Collar–SS Stainless Steel Mesh Screen Over Dome–TC Neo-Loc Test Cap Gasket (2" [51 mm] to 4" [102 mm] NL Bottom

Outlet Only)–VP Vandal-Proof Secured Top–XJ Vertical Expansion Joint (See Z190) –84 Stainless Steel Perforated Gravel Guard–85 Stainless Steel Perforated Extension

OPTIONS

ROOF DRAINS


Page 39


Z180 4-1/2" [114 mm] DIAMETER CORNICE DRAIN Bottom Outlet

ENGINEERING SPECIFICATION: ZURN ZRB180 4-1/2" [114 mm] diameter by 2" [51 mm] highCornice Drain, Dura-Coated cast iron body, plain bronze dome, and membrane flashing clamp.


OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Threaded . . . . . . . . . . . . . . . . 2IP, 3IP . . . . . . . . . . . . . . . . 2" [51 mm]No-Hub (IP w/Z1040) . . . . . . . 2NH, 3NH

SUFFIXES–FS Flat Strainer (ZB or ZN)–G Galvanized Cast Iron–HD 3" [76 mm] High Dome–VP Vandal-Proof Secured Top–4 With 4" [102 mm] High Body; 2" [51 mm] Pipe Size–8 With 8" [203 mm] High Body; 2" [51 mm] Pipe Size

PREFIXES ZRB D.C.C.I. Body with Plain Bronze Dome*ZB D.C.C.I. Body with Polished Bronze DomeZN D.C.C.I. Body with Polished Nickel Bronze Dome

OPTIONS


2 - 3 [51-76] 5 [2] 4.5 [29]

Z165 8-3/8" [213 mm] DIAMETER COMBINATION MAIN ROOF and OVERFLOW DRAINwith Low Silhouette Domes and Double Top-Set® Deck Plate

ENGINEERING SPECIFICATION: ZURN Z165 8-3/8" [213 mm] diameter roof drain and overflow drain.Dura-Coated cast iron bodies with combination membrane flashing clamp/gravel guards, double Top-Set® deck plate, and low silhouette cast iron domes.


OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Inside Caulk . . . . . . . . . . . . 2IC, 3IC, 4IC . . . . . . . . . . . 3-7/8" [98 mm]Threaded . . . . . . . . . . . . . . 2IP, 3IP, 4IP . . . . . . . . . . . . 2-5/8" [67 mm]No-Hub . . . . . . . . . . . . . . . 2NH, 3NH, 4NH . . . . . . . . . . 3-7/8" [98 mm]Neo-Loc . . . . . . . . . . . . . . 2NL, 3NL, 4NL . . . . . . . . . . . 3-3/4" [95 mm]


SUFFIXES–AR Acid Resistant Epoxy Coated Finish–BS Bronze Mesh Screen Over Dome–E Static Extension 1" [25 mm] thru 4" [102 mm] (Specify Height)–ES Static Extension with Secondary Clamp Collar at Body

(For clamping at roof drain body.)–G Galvanized Cast Iron–SC Secondary Clamping Collar–SS Stainless Steel Mesh Screen Over Dome–TC Neo-Loc Test Cap Gasket (2" [51 mm] to 4" [102 mm] NL Bottom

Outlet Only)–VP Vandal-Proof Secured Top–XJ Vertical Expansion Joint (See Z190)–84 Stainless Steel Perforated Gravel Guard–85 Stainless Steel Perforated Extension

OPTIONS


2 - 3 - 4 [51-76-102] 22 [10] 43 [277]


Page 40

ROOF DRAINS


OPTIONS

Z181 6" [152 mm] DIAMETER CORNICE DRAIN Bottom Outlet

ENGINEERING SPECIFICATION: ZURN ZRB181 6" [152 mm] diameter by 4" [102 mm] high CorniceDrain, Dura-Coated cast iron body, plain bronze dome, and membrane flashing clamp.


OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Threaded . . . . . . . . . . . . . . . . 3IP, 4IP . . . . . . . . . . . . . . . 4" [102 mm]No-Hub (IP w/Z1040) . . . . . . . 3NH, 4NH


SUFFIXES–BS Bronze Mesh Screen Over Dome–C Underdeck Clamp–FS Flat Strainer (ZB or ZN)–G Galvanized Cast Iron–HD 5-3/4" [146 mm] High Dome–R Roof Sump Receiver–VP Vandal-Proof Secured Top–8 With 8" [203 mm] High Body; 3" [76 mm] and 4" [102 mm]

Pipe Size

Z182 4" [102 mm] DIAMETER CORNICE DRAIN 90° Outlet

ENGINEERING SPECIFICATION: ZURN ZRB182 4" [102 mm] diameter Cornice Drain, Dura-Coatedcast iron 90° side outlet body, plain bronze dome, and membrane flashing clamp.


OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Threaded . . . . . . . . . . . . . . . . . . . . 2IP . . . . . . . . . . . . . . . . 4" [102 mm]

SUFFIXES–FS Flat Strainer (ZB or ZN)–G Galvanized Cast Iron–HD 3" [76 mm] High Dome–VP Vandal-Proof Secured Top–45 45° Side Outlet Body


OPTIONS


3 [76] 7 [3] 12 [77]

4 [102] 8 [4]


2 [51] 5 [2] 4.5 [29]

ROOF DRAINS


Page 41


OPTIONS

Z185 6" [152 mm] DIAMETER CORNICE DRAIN 90° Outlet

ENGINEERING SPECIFICATION: ZURN ZRB185 6" [152 mm] diameter Cornice Drain, Dura-Coatedcast iron 90° side outlet body, plain bronze dome, and membrane flashing clamp.


OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Threaded . . . . . . . . . . . . . . . . . . . 3IP . . . . . . . . . . . . . 5-1/8" [130 mm]

4IP . . . . . . . . . . . . . 5-5/8" [143 mm]

SUFFIXES–FS Flat Strainer (ZB or ZN)–G Galvanized Cast Iron–HD 5-3/4" [146 mm] High Dome–VP Vandal-Proof Secured Top–45 45° Side Outlet Body


Dimensions in Inches [mm] GrateA App. Wt. Open Area

Pipe Lbs. Sq. In.Size B D H L L' M [Kg] [cm2]

2 [51] 1-1/2 [38] 6-5/8 [168]

3 [76] 7-1/2 2 [51] 2-3/4 6-3/8 6-3/8 6-1/8 [156] 22 [10]

20 [129]

4 [102] [191]

2-1/2 [64] [70]

[162]

[162]

5-5/8 [143] 20 [9]

6 [152] 12-1/2 3-1/2 [89] 3-1/2 8-3/8 8-3/8 7-7/8 [200] 32 [15]

57 [368]8 [203] [318] 4-5/8 [118] [89] [213] [213] 7-3/8 [187] 33 [15]

Z187 6" x 7" [152 mm x 178 mm] or 8" x 12" [203 mm x 305 mm] OBLIQUE SCUPPER DRAIN

ENGINEERING SPECIFICATION: ZURN Z187 6" x 7" [152 mm x 178 mm] or 8" x 12" [203 mm x305 mm] Scupper Drain, Dura-Coated cast iron body with reversible back or bottom outlet, obliquegrate with 90° combination frame, and membrane flashing clamp.


OUTLETOUTLET DESIGNATIONTYPE Pipe Size/Outlet TypeThreaded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2IP, 3IP, 4IP, 6IP, 8IPNo-Hub (IP w/Z1040) . . . . . . . . . . . . . . . . . . . . 2NH, 3NH, 4NH, 6NH, 8NH

PREFIXES Z D.C.C.I. Body with Grate*ZB D.C.C.I. Body with Polished Bronze GrateZN D.C.C.I. Body with Polished Nickel Bronze GrateZRB D.C.C.I. Body with Plain Bronze Grate

SUFFIXES–BS Bronze Mesh Screen Over Grate–DA Downspout Adapter (Previously Z188)–FG Flush Grate–G Galvanized Cast Iron–TS Secured Top–VP Vandal-Proof Secured Top

OPTIONS

A Approx. Grate Pipe Size Wt. Open Area Inches [mm] Lbs. [Kg] Sq. In. [cm2]

3 [76] 8 [4] 12 [77]

4 [102] 10 [5]


Page 42

ROOF DRAINS


Dimensions in Inches [mm] Approx. Grate A Wt. Open Area Pipe Size Lbs. [Kg] Sq. In. [cm2]

2 [51]

3 [76] 18 [8] 20 [129]

4 [102]

OPTIONS

OPTIONS

Z189 5" x 6" x 11" [127 mm x 152 mm x 279 mm] SCUPPER DRAIN

ENGINEERING SPECIFICATION: ZURN Z189 5" x 6" x 11" [127 mm x 152 mm x 279 mm] ScupperDrain, Dura-Coated cast iron body with 45° outlet and flush type strainer with combination frameand membrane flashing clamp.


OUTLET 'E'OUTLET DESIGNATION BODY HT.TYPE Pipe Size/Outlet Type DIM.Threaded . . . . . . . . . . . . . . . 2IP, 3IP, 4IP . . . . . . . . . . . . . . . . See ChartNo-Hub (IP w/Z1040) . . . . . . 2NH, 3NH, 4NH

PREFIXES Z D.C.C.I. Body with Grate*ZB D.C.C.I. Body with Polished Bronze GrateZN D.C.C.I. Body with Polished Nickel Bronze Grate

SUFFIXES–BS Bronze Mesh Screen Over Grate–DA Downspout Adapter–G Galvanized Cast Iron–OB Oblique Grate–TS Secured Top–VP Vandal-Proof Secured Top–90 Threaded Side Outlet Body

Dimensions in Inches [mm] Approx. A B Wt. Pipe Size Min. Max. C D F Lbs. [Kg]

2 [51] 3-5/8 [92] 5 [127]

2-3/4 [70] 8 [4]

3 [76] 6-1/2 [165] 8-1/2 [216] 4-5/8 [118] 3-1/4 [83] 11 [5]

4 [102] 5-1/2 [140] 4-3/4 [121] 3-3/4 [95] 13 [6]

5 [127] 6-7/8 [175] 8-5/8 [219]

6-1/2 [165] 4-1/4 [108] 18 [8]

6 [152] 7-7/8 [200] 5 [127] 5 [127] 25 [11]

8 [203] 7-7/8 [200] 10-7/8 [276] 9-7/8 [251] 6 [152] 35 [16]

10 [254] 7-7/8 [200] 10-7/8 [276] 11-3/4 [299] 6 [152] 6-7/8 [175] 45 [21]

ENGINEERING SPECIFICATION: ZURN ZRB190 Vertical Expansion Joint, Dura-Coated cast iron body,packing gland and siliconed bronze sleeve with preformed neoprene packing gasket.


OUTLET 'E'OUTLET DESIGNATION BODY HT.TYPE Pipe Size/Outlet Type DIM.Threaded . . . . . . . . . . . . 2IP, 3IP, 4IP, 5IP, 6IP, 8IP, 10IP . . . . . See ChartNo-Hub (IP w/Z1040) . . . 2NH, 3NH, 4NH, 5NH, 6NH, 8NH

PREFIXES ZRB D.C.C.I. Body with Polished Bronze Sleeve*

SUFFIXES–G Galvanized Cast Iron

Z190 VERTICAL EXPANSION JOINT

ROOF DRAINS


Page 43


OPTIONS

Z191 5" x 4" x 24" [127 mm x 102 mm x 610 mm] DOWNSPOUT BOOT

CONNECTION (Specify pipe size in inches and type of outlet.) CONNECTION DESIGNATIONCONNECTION TYPE Pipe Size/Outlet TypeNo-Hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4NH

PREFIXES Z D.C.C.I. Body*

SUFFIXES–G Galvanized Cast Iron–RD Round Inlet and Outlet

Dimensions in Inches [mm] Approx.Product A Wt.

Designation Size Pipe Size Lbs. [Kg]

-24 5 x 4 x 24 [127 x 102 x 610] 4 [102] 30 [14]

ENGINEERING SPECIFICATION: ZURN Z191 5" x 4" x 24" [127 mm x 102 mm x 610 mm] Down spout Boot, Dura-Coated cast iron body and strap with 1/4" [6 mm] diameter cast holes for flat head bolts.


Designation Size Pipe Size Lbs. [Kg]

Z191-RD 4 x 18 [102 x 457] 4 [102] 20 [9]

Z191-RD 4" x 18" [102 mm x 457 mm] DOWNSPOUT BOOT

ENGINEERING SPECIFICATION: ZURN Z191-RD Downspout Boot, Dura-Coated cast iron body,round inlet and outlet, and strap with 1/4" [6 mm] diameter cast holes for flat-head bolts.

OPTIONS


PREFIXES (See chart for pricing)Z D.C.C.I. Body*



Page 44

ROOF DRAINS


OPTIONS

Dimensions in Inches [mm] Approx. A Wt. Open Area Pipe Size B C Lbs. [Kg] Sq. In. [cm2]

1-1/2 - 2 [38-51] 3-1/8 [79] 6-3/8 [162] 9 [4]

3 [76] 4-3/16 [106] 7-5/8 [194] 12 [6]

4 [102] 5-1/4 [133] 9-1/8 [232] 14 [7] 2 : 1

5 [127] 6-3/16 [157] 10-1/8 [257] 16 [7]

6 [152] 7-3/16 [183] 11-5/8 [295] 18 [8]

Z193 VANDAL-PROOF HOODED VENT CAP

ENGINEERING SPECIFICATION: ZURN Z193 Vandal-Proof Vent Cap, Dura-Coated cast iron bodyand hooded dome cap, vandal-proof securing device.


OUTLET 'E' BODYOUTLET DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Inside Caulk . . . . . . . . . . . . 1.5IC, 2IC . . . . . . . . . . . 5-11/16" [145 mm]

3IC, 4IC, 5IC, 6IC . . . . . 5-9/16" [141 mm]


PREFIXES Z D.C.C.I. Body and Dome Cap*

OPTIONS

Z192 4" x 3" [102 mm x 76 mm] DOWNSPOUT BOOT

ENGINEERING SPECIFICATION: ZURN Z192 4" x 3" x 24" [102 mm x 76 mm x 610 mm]Downspout Boot, Dura-Coated cast iron body and strap with 1/4" [6 mm] diameter cast holes for flat head bolts.


SUFFIXES–CA Cleanout Access with Plug–G Galvanized Cast Iron



Designation Size Pipe Size B Lbs. [Kg]

-12 12 [305] 14 [6]

-18 4 x 3 [102 x 76] 4 [102] 18 [457] 20 [9]

-24 24 [610] 27 [12]

ROOF DRAINS


Page 45


Dimensions in Inches [mm] Approx. A Wt. Pipe Size B Lbs. [Kg]

1-1/2 [38] 3 [76] 2 [1]

2 [51] 3-1/2 [89] 3 [1]

3 [76] 4-3/4 [121] 4 [2]

4 [102] 5-5/8 [143]

5 [127] 6-3/4 [172] 6 [3]

6 [152] 7-3/4 [197] 7 [3]

OPTIONS

Z196 VENT STACK FLASHING SLEEVE

ENGINEERING SPECIFICATION: ZURN Z196 Vent Stack Flashing Sleeve, Dura-Coated cast iron body,inside caulk type.

CONNECTION (Specify pipe size in inches and type of outlet.) CONNECTION 'E' BODYCONNECTION DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Inside Caulk . . . . . . . . 1.5IC, 2IC, 3IC, 4IC, 5IC, 6IC . . . 3-1/2" [89 mm]



Dimensions in Inches [mm] Approx. A Wt. Pipe Size C D K Lbs. [Kg]

1-1/2 [38] 6-1/2 [165]

2-5/8 [67] 3 [76]

12 [6] 2 [51] 3-1/8 [79] 11 [5] 3 [76] 4-1/4 [108]

3-1/8 [79] 13 [6]

4 [102] 8-1/2 [216]

5-1/4 [133] 18 [8] 5 [127] 9-1/2 [241] 6-1/2 [165] 2-1/2 [64] 20 [9] 6 [152] 10-1/2 [267] 7-1/2 [191] 3-1/8 [79] 26 [12] 8 [203] 14-1/2 [368] 9-3/4 [248] 52 [24] 10 [254] 16-1/2 [419] 11-5/8 [295] 2-3/4 [70] 45 [21] 12 [305] 18-1/2 [470] 13-5/8 [346] 60 [27]

OPTIONS

ENGINEERING SPECIFICATION: ZURN Z195 Vent Stack Flashing Sleeve, Dura-Coated cast ironbody with fixed position combination membrane flashing flange and clamp.

Z195 VENT STACK FLASHING SLEEVE

CONNECTION (Specify pipe size in inches and type of outlet.) CONNECTION 'E' BODYCONNECTION DESIGNATION HT. DIM.TYPE Pipe Size/Outlet Type In./[mm]Inside Caulk . . . . . . . . . . . .1.5IC, 2IC . . . . . . . . . . . . . . 8" [203 mm] 3IC, 4IC, 6IC . . . . . . . . . . . 8-1/8" [206 mm] 5IC . . . . . . . . . . . . . . . . . . 8-1/2" [216mm] 8IC, 10IC, 12IC . . . . . . . . . 8-3/4" [222mm]


SUFFIXES–CF Bottom Clamping Flange–G Galvanized Cast Iron


Page 46

ROOF DRAINS


OPTIONS

Dimensions in Inches [mm] Approx. Product A B Wt. Designation Pipe Size Wall Thickness Lbs. [Kg]

– 8 8-1/2 [216] 26 [12]

– 11 11 [279] 29 [13]

– 13 4 [102] 13-1/2 [343] 31 [14]

– 17 17-1/2 [445] 35 [16]

– 22 22-1/2 [572] 40 [18]

Z198 PARAPET SCUPPER SLEEVE

ENGINEERING SPECIFICATION: ZURN Z198 Parapet Scupper Sleeve, Dura-Coated cast iron bodywith fixed position combination membrane flashing flange, and clamp and parapet wall face closing.

WALL THICKNESS (Specify thickness and size.) CONNECTION DESIGNATIONCONNECTION TYPE Pipe Size/Outlet TypeHub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4HB



OPTIONS

Dimensions in Inches [mm] Approx. A B Wt. Pipe Size Pipe Sleeve C D E Lbs. [Kg]

1-1/2 [38] 2-1/2 [64] 6 [3]

2 [51] 3 [76] 6-1/2 [165] 4 [102] 2-3/4 [70] 7 [3]

3 [76] 4 [102] 9 [4]

4 [102] 5 [127] 8-1/2 [216] 6 [152] 3-1/4 [83] 10 [5]

5 [127] 6 [152] 9-1/2 [241] 7-1/8 [181] 3-3/8 [86] 13 [6]

6 [152] 8 [203] 11-7/8 [302] 9-3/8 [238] 3-5/8 [92] 19 [9]

Z197 RISER SLEEVE

ENGINEERING SPECIFICATION: ZURN Z197 Riser Sleeve, Dura-Coated cast iron body, doublethreaded pipe connector with combination membrane flashing flange. (Pipe sleeve furnished by others.)

CONNECTION (Specify pipe size in inches and type of outlet.) CONNECTION 'E'CONNECTION DESIGNATION BODY HT.TYPE Pipe Size/Outlet Type DIM.

Threaded . . . . . . . . . . 1.5IP, 2IP, 3IP, 4IP, 5IP, 6IP . . . . . . . . . See Chart



ROOF DRAINS


Page 47


Z199-DC DOWNSPOUT COVER

ENGINEERING SPECIFICATION: ZURN ZS199-DC Downspout Cover, round fabricated stainlesssteel frame with fabricated, secured, perforated, stainless steel hinged strainer.

PREFIXESZS Type 304 Stainless Steel*

SUFFIXES–CP Chrome Plated–VP Vandal-Proof Secured Top–5 5" [127 mm] Long Downspout Frame

OPTIONS


A Pipe Size B C D

3 [76] 3-1/2 [89] 4-1/4 [108] 7-3/4 [197] 4 [102] 4-1/2 [114] 5-1/4 [133] 8-3/4 [222] 6 [152] 6-5/8 [168] 7-3/8 [187] 10-7/8 [276] 8 [203] 8-5/8 [219] 9-3/8 [238] 12-7/8 [327] 10 [254] 10-3/4 [273] 11-1/2 [292] 15 [381] 12 [305] 12-3/4 [324] 13-1/2 [343] 17 [432] 15 [381] 15 [381] 16-5/8 [422] 20-1/8 [511]

Dimensions in Inches [mm] Approx. A Wt. Pipe Size B C D F Lbs. [Kg]

2 [51] 5 [2]

3 [76] 6 [152] 3-1/2 [89] 5-1/2 [140] 4 [102]

6 [3]

4 [102] 7 [178] 3-1/2 [89] 5-1/2 [140] 5 [127] 7 [3]

5 [127] 12 [6]

6 [152] 9 [229] 3-1/2 [89] 5-1/2 [140] 7-1/8 [181]

13 [6]

8 [203] 10-7/8 [276] 3 [76] 5-1/2 [140] 9-1/8 [232] 14 [7]

10 [254] 12-7/8 [327] 3-1/2 [89] 6 [152] 11-1/8 [283] 15 [7]

12 [305] 14-5/8 [371] 4-1/16 [103] 6-9/16 [167] 13-1/8 [333] 17 [8]

Z199 DOWNSPOUT NOZZLE

ENGINEERING SPECIFICATION: ZURN ZANB199 Downspout Nozzle, nickel bronze body, threadedinlet and decorative face of wall flange and outlet nozzle.

CONNECTION (Specify pipe size in inches and type of outlet.) CONNECTION DESIGNATIONCONNECTION TYPE Pipe Size/Outlet TypeThreaded . . . . . . . . . . . . . . . . . . . . . . . . . 2IP, 3IP, 4IP, 5IP, 6IP, 8IP, 10IP

PREFIXES ZANB All Nickel Bronze Body*ZAB All Polished Bronze BodyZARB All Plain Bronze Body

SUFFIXES–SS Stainless Screen

OPTIONS

ZURN INDUSTRIES, LLC SPECIFICATION DRAINAGE OPERATION1801 PITTSBURGH AVENUE, ERIE, PA 16502 PHONE 814/455-0921 FAX: 814/454-7929 www.zurn.com

©2012 Zurn Industries, LLC Form No. SD14, Rev. 2/12

zurn roof drains

Documents

roof installation

roof loading

roof drainnote

roof size3

roof pitch4

proper roof drain

zurn roof drains

roof causes expansion