12089-66 v006 1221 - interline brands · v006 / 12089-66 1221 i25 i24 ... (electro-smog). do not...

swingo 755B/855B/1255B Power

V0

06 /

12

089

-66

122

1

I25

I24

I23

I22

I21

I20

I19

I18

trsv

slro

pt

pl

no

nl

ith

ufr

fies

end

ed

acz

*120

89-6

6*

I24

I23

I22

I21

I20

I19

I18

trsv

slro

pt

pl

no

nl

ith

ufr

fies

end

ed

acz

Translation of the original Instructions of Use

Symbols

Intended use of machinery

The TASKI swingo 755B/855B/1255B power are scrubber dryer machines that are designed for commercial use (for example, in hotels, schools, hospitals, factories, shopping centres, offices, etc.).Under strict observation of the instructions for use, they can be used for the wet cleaning of hard floor coverings.These machines are exclusively designed for indoor use only .

Content

Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Translation of the original EU Declaration of Conformity . . . . . . . . . 36Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Preparation for operation/Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 38Beginning work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41End of operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Service, maintenance and care. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Dimensions of the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Safety instructions

Due to their design and construction, TASKI machines comply with health and safety requirements of the EC guidelines and therefore carry the CE sign.ATTENTION!

Before first start-up, it is essential that you read the instructions for use and the safety notes carefully.Keep the instructions for use in an easily accessible place so that they can be consulted at any time.

Non-observance of this information can endanger people and / or cause servere damage!

Non-observance of this information can lead to malfunctions and property damage!

Indicates important information about economical use. Non-observance of this information could lead to malfunctions!

Marks worrking steps that you must carry out one after the other.

Caution:These machines may not be used for polishing, the application of wax, cleaning carpets or the vacuuming up of dust. The wet cleaning of parquet and laminate floors with this machine is carried out at your own risk.

Changes to the machines that have not been authorised by Diversey will lead to the cancellation of the Safety Marks and the CE conformity. Any use of the machines contrary to its intended purpose can lead to injuries to persons and damage to the machine and to the working environment.In such cases, any claims under the guarantee and warranty claims will normally become invalid.

STOPSTOP

•

STOPSTOP

Persons (including children) who are not able to use this machine safely due to their physical, sensory or mental capabilities or their inexperience or lack of knowledge may not use this machine without the supervision or instruction by a responsible person!

Children should be supervised to ensure that they do not play with the appliance.

Do not use this machine in rooms in which explosive and easily inflammable materials (such as petrol solvents, fuel oil, dusts, etc.) are stored or processed. The electrical or mechanical components could lead to the ignition of these materials.This machine must not be used in rooms that are subject to electro-magnetic loading (electro-smog).

Do not use this machine to vacuum toxic, poisonous, caustic or irritating substances (e.g. hazardous dusts, etc.). The filter system will not adequately retain these kinds of materials. A possible impairment of the health of the user and of third parties cannot be excluded.

While operating the machine, take note of the surrounding area and pay particular attention to third parties and children!In particular, the speed of the machine should be reduced in the vicinity of areas of unclear vision, for example, in front of doors or curves.

The machine may only be used by persons who have been suitably instructed in its use.

Neither persons or objects may be transported with the machine!

In case of damage to components that are relevant to safety, such as tool covers, battery disconnection socket, power supply cord, battery charger or covers provide access to current-carrying parts, the operation of the machine must be stopped immediately!

Regularly check the power supply cord for tearing or aging, and do not put the machine into operation if it is not in a safe and suitable condition!

Caution:Repairs to mechanical or electrical parts of the machine must only be undertaken by Diversey authorised customer service workshops or experts who are experienced in all relevant safety regulations.

Minimum requirements on the H05VV-F3G1 or H05VV-F3G1.5power cord.

Caution:This machine is only intended for use in dry areas, and must not be used or stored in the open air or under damp conditions.

Caution:Pay attention to the accident prevention regulations!

Caution:Switch off the suction unit immediately if foam or liquid escape from the machine!

See page 44 for further procedure .

Caution:Only use tools that are specified in these instructions for use under Accessories or that have been recommended by the TASKI technical specialist (page 45), as the use of other tools could impair safety.

Caution:The protection of persons is based on the special national regulations and the information from the detergent producer!

STOPSTOP

STOPSTOP

STOPSTOP

STOPSTOP

STOPSTOP

STOPSTOP

STOPSTOP

STOPSTOP

35

I25

Important! Switch the machine off when you:

• e.g. carry out cleaning or maintenance work, or convert the machine to another function

• store it in a suitable room to avoid any unauthorised use of the unit• leave it standing without supervision

To do this, remove the keyswitch, pull out the battery disconnection socket and prevent the machine from rolling away (e.g. by placing a wedge under it).

Store the machine in a dry, dust-free room with a corrosion-free atmosphere.

The temperature must not fall below +10 °C or exceed +35 °C. Low temperatures, damp and dust can significantly reduce the service life of the electrical components.

Translation of the original EU Declaration of Conformity

We hereby declare that the product described below conforms to the relevant safety and health-related requirements of the appropriate EU Directive, in both its design and construction, as well as in the version that we market.

This declaration shall cease to be valid if modifications are made to the product without our approval.

Applicable EU Directives:

Directive 2006/42/EG| Directive 2004/108/EG

Harmonised standards applied:

EN 60 335-1 / EN 60335-2-72 / EN 62233 / EN 55014-1 / EN 55014-2 / EN 61000-3-2 / EN 61000-3-3 / EN 55012

Internal measures have been taken to ensure that the products always correspond to the requirements of the latest EU Regulations and the standards that are currently in use

Download Link for the original EU Declaration of Conformity:

http://www.espares.diversey.com/manuals

Caution:This machine may not be operated without batteries!

Caution:The batteries may only be operated with a battery charger that has been tested to the latest state-of-the-art according to EN 60335-2-29!

(only type:CO755.1/CO855.1/CO1255.1)

Only use the machine on level floors or on gradients of 2% or less.

This symbol on the machine indicates that it is not suitable for use on surfaces with greater gradients.

The tank cap must be closed when moving or driving the machine.

Noise emission and vibrations:TASKI machines and units have been designed so that any danger to health through the noise emitted or through vibrations can be excluded according to the current state of knowledge. Refer to the technical information on page 44.

2%

Designation: Automatic machine for the treatment of floors for commercial purposes.

Product: scrubber dryerModel: swingo 755B power / swingo 855B power /

swingo 1255B powerModel: CO755.1 | CO755.1X | CO855.1 | CO855.1X |

CO1255.1 | CO1255.1X |

Serial number: Refer to the rating plate on the machine

Trade mark:

Manufacturer: Diversey Europe Operations B.V. - 1083 HJ Amsterdam - Netherland

Person authorised to compile the technical file:Angelo SabatinoMgr Regulatory AffairsDiversey Switzerland Services GmbHEschlikonerstrasse9542 Münchwilen TG

36

I24

I23

I22

I21

I20

I19

I18

trsv

slro

pt

pl

no

nl

ith

ufr

fies

end

ed

acz

Overview

1 Speed control2 Emptying hose for solution tank (blue cap)3 Emptying hose for recovery tank (red cap)4 Disconnector charger jack (coded)5 Variant: Foot pedal tool6 Foot pedal squeegee7 Squeegee8 Hour counter (optional)9 Lock battery compartment (optional)10 Tools (brush, pad drive, etc.)11 Brush unit12 Solution dosing control13 Suction unit button14 Keyswitch15 Eco mode16 Cleaning solution dosing control17 Indicator brush down/Automatic brush lowering (Option 1255)18 Battery indicator19 Battery fully charged20 Battery charging (Power plug connected)21 Failure of battery or charger indicator22 Service indicator

23 Filling level (max.)24 Fresh water filter25 Recovery tank26 Float (overfilling protection for recovery tank)27 Vacuum air filter28 Dirt sieve29 Solution tank30 Dosing aid31 Tank lid32 Tank lid catch

6

7 8 9 10

5

234

22

1

192021 18 17 16 15

14

13

12

11

Eco

29 2830

23

24

25

26

27

32

31

max.60°Cmax.140°F

MAX3/4

1/2

37

I25

Preparation for operation/Operation

Batteries

Safety measures when working with batteries:

Battery connection diagram

Charging procedure (traction block batteries with integrated charging unit)

After completing the charging and with immediate use

Charging procedure (traction block batteries with external charging unit)

Charging procedure (wet batteries with external charging unit)

• Protective goggles must be worn when working on the batteries.

• Do not subject batteries to an open flame or heat as there is a danger of explosion from the electolytic gas present in the cells!

• No smoking!

• Danger of chemical burns!

Caution:The battery must always be clean and dry. Do not place any metallic objects on the battery.

The integrated charging unit is only suitable for maintenance-free gel traction block batteries.

Caution:Batteries may only be installed or dismounted by customer service personnel or specialists approved by Diversey who are aware of all the safety regulations that apply here!

-

+

-

+

-

+

-

+

-

+

-

+

-

+

-

+

-

+Powerboard

Powerboard

+

-

+ -

+ -

+

-

SWINGO 1255BOnboardcharger

Onboardcharger

Powerboard

Powerboard

Onboardcharger

Onboardcharger

-

+

-

+

-

+

-

+

-

++

-

+ -

+ -

+

-

SWINGO 755BSWINGO 855B

• Check that the machine has been switched off with the keyswitch.• Disconnect the battery from the machine using the battery disconnection

socket.• Plug the power supply cord into the mains socket.

When the charging process is complete, the green indicator lights up.

The yellow indicator lights up permanently until approx. 90% of the battery capacity has been reached. After that, the indicator blinks until the battery is fully charged.

• Leave the power supply cord connected to the mains until you use the machine again. The on-board charger unit automatically monitors and charges the batteries. The energy consumption in the mode is limited to a few milliwatts.

If a fault occurs during the charging process as the result of a defect in the charging unit, an interruption of a cable or a defective battery cell, the red indicator will light up.

• Unplug the connection to the mains socket.• Connect the battery to the machine with the battery disconnection socket.


socket.• Connect the battery disconnection socket to the external battery charging

unit (pay attention to the voltage from the mains supply socket).

Caution:Follow the instructions for use for your battery charger!

Caution:If the machine is assembled with a wet battery kit (optional) the machine must be used with wet batteries only!

Wet batteries must not be charged with the internal charger!

Battery compartment must be open during charging.

Wet batteries must be charged in ventilated rooms only!

The gas given off could be ignited!

• Switch the machine off using the keyswitch and remove the key.• Disconnect the battery from the machine using the battery disconnection

socket.• Check that the tanks are empty.

• Unlock the battery compartment (with a screw driver) and in a sufficiently large area, lift the tank until it locates into its self support position.

38

I24

I23

I22

I21

I20

I19

I18

trsv

slro

pt

pl

no

nl

ith

ufr

fies

end

ed

acz

Maintenance of batteries (only wet batteries)

Please follow the instructions of use for your battery charger!

Opening battery compartment for maintenance

Closing battery compartment

After end of maintenance

Preparing to drive

Attaching tools

Check: • that the brushes are not below the red marking and that the bristle length is

no less than 1 cm.• the pad for wear before using.

Variant:(Option 1255) Automatic brush lowering

Tank position for charging.

• Connect the battery disconnection socket to the external battery charging unit (pay attention to the voltage from the mains supply socket).

Caution:Follow the instructions for use for your external battery charger!

• Turn on the battery charger.

Caution:When maintenance of batteries takes place, they must be disconnected from the machine!


socket.• Lower the squeegee.

• Check that the tanks are empty.

• Unlock the battery compartment, by pushing a screw driver or a similar tool into the allowed opening.

• Lift the tank until it locates into its self support position.

Tank position before it is altered for battery maintenance.

• Lock the tank lid.• Stand behind the machine.• Carefully open the battery compartment until

the drive handle is lying on the floor.

Tank position for battery maintenance.

• Stand behind the machine and lift the tank until it rests on the tank self support.

• Hold the tank and press the tank support inwards.

Now lower the tank until it locates into place.

• Connect the battery to the machine with the battery disconnection socket.• Raise the squeegee.

• Switch on the keyswitch.

The indicators light up briefly.

The battery indicator displays that the machine is ready for operation(on malfunction see page 44).

• Hold the handle and adjust to a height which is comfortable to work with.

By lightly pressing the speed control in the direction of drive, the machine is set in motion. Letting the speed control go stops the machine.

• Switch the machine off using the keyswitch and remove the key.

Working with worn out, damaged and or wrong tools, could result in possible damage to floors or their protective layers.

• Position the tool below the brush unit.• Switch on the keyswitch.


• Press the brush unit button.

While being lowered, the brush drive begins to pulse slowly. This centres and locks the tool into place.

The display lights up.

39

I25

Pedal brush unit

Attach squeegee

Filling water

Dosage:

Only use chemical products recommended by the manufacturer.

For precise dosing, use the scale in the dosing aid.

The level indicators on the tank correspond to those on the dosing aid. The machine type is noted on the dosing aid!

Dosing examples (The concentration is product dependent)

• Unlatch the foot lever and slowly lower the tool.

While being lowered, the brush drive begins to pulse slowly. This centres and locks the tool into place.

The display lights up.

When the brush is fully lowered, moving the machine forwards and backwards slightly makes coupling easier.

• Switch the machine off.• Lay the squeegee under the squeegee holder

so that the squeegee holder is underneath the attachment cord.

• Press the foot pedal down until the squeegee locks into place.

• Attach the suction hose to the squeegee.

Caution:Maximum permissible water temperature 60 °C/140 °F.

• Switch the machine off using the keyswitch and remove the key.• Reach into the opening between the tank lid and

the tank.

Palm facing upwards.

• Open the lid until the self support locates on the tank wall.• Remove the dosing aid.

• Fill water into the solution tank.

Maximum permissible filling level (page 40).

1255

755 / 855

max.60˚C

max.140˚F

Caution:Wear protective gloves, goggles and the corresponding (protective) work clothing when handling chemical products!

Caution:Using other chemicals (e.g. chemicals containing solvents, chlorine, hydrochloric acid and hydrofluoric acid) can damage or destroy the machine.

Dosage Tank capacity Dosing aid

0,5% 1/2 1 x 1/2

MAX 1 x MAX

1% 1/2 1 x MAX (2 x 1/2)

MAX 2 x MAX

• Dosing aid application

• Add the product measured with the dosing aid to the water in the solution tank.

• Lift the tank lid slightly.• Gently press the tank lid support inwards.• Close the tank lid.• By exerting slight pressure onto the front part of the tank lid, you can click it

into the latch.

When using the automatic dosing system „IntelliDose“, please follow the corresponding Instructions for Use.

40

I24

I23

I22

I21

I20

I19

I18

trsv

slro

pt

pl

no

nl

ith

ufr

fies

end

ed

acz

Beginning work

During these 5 minutes:

Always turn the keyswitch to the 0-position and remove the key from the machine if you are going to be out of sight of the machine.

During these 5 minutes:

Cleaning method

Direct method:

Scrubbing and vacuuming in one pass.

Indirect working method:

Apply the cleaning solution (only scrubbing), afterwards scrubbing and vacuuming.

The cleaning method is described in detail in the ”Method Card”. You can obtain this from your TASKI partner.

Refilling the solution tank

A rattling noise from the pump indicates that the solution tank is empty.

End of operation

Variant: (Option 1255) Automatic brush lowering

Pedal brush unit (optional):

Drain the recovery tank / solution tank

The disposal of the dirty water or the cleaning solution must be carried out in accordance with the appropriate national regulations.

Clean the recovery tank / solution tank

Caution:Always wear non-slip shoes and appropriate work clothing while working with this machine!

• Lower the squeegee.



• Lower the brush unit using either the brush unit button or brush unit pedal, see page 39.

• First press the solution dosing control button, and then the vacuum on.


• Choose the volume of solution (+/- button for volume control).

The chosen setting is displayed with green lights.

• By gently pressing the speed control in the direction of drive, the machine is set in to motion.

The tools start to turn and the solution is fed through the centre.

The machine switches itself off again after 5 minutes.

• no manipulations of any kind may be carried out on the brushes.• the operator must remain within sight of the machine.

• only the squeegee may be cleaned from sucked-in or jammed objects.• the operator may on ly leave the machine for the purposes of clearing the

area to be cleaned, but must remain in visual contact with the machine.

Caution:Do not clean without solution, as it could cause floor damage.

• Stop cleaning.• Refill the tank, see page 40.

• Stop the flow of solution.

• Drive a few metres so that the tools rotate further for a short time. You will avoid dripping by doing this.

Very important when using contact pads!

• Press the brush unit button to raise the tool.

• To raise the tool, press down the pedal and lock it in place.

• Drive on a few metres further in order to pick up the remaining dirty water.• Raise the squeegee.

Allow the suction unit to continue running until the rest of the dirty water has been sucked into the hose.

• Switch off the suction unit first, and then the keyswitch.

Always drain and clean the recovery tank every time you use the machine.

If the dirty water is allowed to stand, unpleasant smells and deposition of the dirt will take place after a few hours.

• Switch the machine off.• Remove the drainage hose from its holder.

Open the red or blue cap situated near the handle and lower the end of the hose slowly to drain the solution out.

• Switch the machine off.• Open the lid until the self support locates on the tank wall.• Remove the coarse dirt sieve (yellow), empty and clean it.• Thoroughly rinse out the recovery tank with flowing water.• Then thoroughly rinse out the solution tank with clean water.• Check the float is functioning correctly and that the suction filter (yellow) is

clean.

In case of damage or soiling of the float and suction filter, please refer to page 43.

• After draining and cleaning, screw the red and blue caps on again, and hang the hoses from their holders again.

41

I25

Clean solution tank filter

Cleaning the tools

Variant: (Option 1255) Automatic brush lowering

Pedal brush unit (optional):

Swingo 1255B model:

Swingo 755B/855B model:

Removing and cleaning the squeegee

Cleaning the machine

Storage / parking of machine (machine is idle)

Store the machine with the tank cap slightly open, by:• lifting the tank lid and turning the dosing aid upside down.• then rest the tank lid on the dosing aid.

Service, maintenance and care

The machine's maintenance is a pre-condition for trouble-free running and a long life.

Caution:Clogged filters reduce the flow of the cleaning solution. As a consequence you may damage the floor coating.

• Switch the machine off.• Once the solution tank has been drained, screw

the yellow cap from the solution tank filter and pull it away from its holder.

• Rinse the filter under running water.

If necessary, the filter should be descaled with a 10% TASKI calcacid solution.

The filter is lower than the tank outflow. A residual amount of solution will flow out once the filter cap has been unscrewed.

• Refit the solution filter.



• Press the brush unit button to raise the tool.


• Switch the machine off using the keyswitch and remove the key.• To raise the tool, press down the pedal and lock

it in place.

• Press the tool ejection handle briefly but firmly with your foot.

• Clean the tool under running water.

• Turn the tool anticlockwise away from the tool coupling using your foot.

• Clean the tool under running water.

• Switch the machine off.• Pull the suction hose away from the squeegee support.

• LIft the squeegee with the foot.

• Press the locking springs together. The squeegee will thereby be released and can be removed.

• Clean the squeegee with water using a brush.

Optimal suction results can only be obtained with clean and intact blades!

Caution:Never clean the machine with high water pressure or a water hose.

The ingress of water into the machine might cause considerable damage to mechanical or electrical parts.

• Wipe down the machine with a damp cloth.

We recommend that you disconnect the battery from the machine using the battery disconnection socket when storing / parking the machine and when charging the battery.

The dosing aid holds the tank lid slightly open, allowing the tank to dry out. As a result, the formation of mould and unpleasant smells can be reduced.

Caution:Only TASKI branded spare parts must be used, otherwise warranties and liabilities will be omitted!

Symbols: = After use, = Every week, = Every month, ⊗ = Service light

Activity ⊗ page

Recharge batteries 38

Clean all parts marked yellow

Drain and clean the tanks 41

Wipe down the machine with a damp cloth 42

Refill distilled water (wet batteries). Please follow the manufacturers instructions of use booklet for these batteries!

Clean the tank lid seal, check for cracks and repla-ce if necessary

Maintenance programs by TASKI service made by TASKI technician

42

I24

I23

I22

I21

I20

I19

I18

trsv

slro

pt

pl

no

nl

ith

ufr

fies

end

ed

acz

Service intervals

TASKI machines are build to the highest quality standards, and their safetx is checked in the factory and by authorised inspectors . Electrical and mechanical parts are subject to wear or aging if used for long periods of time.

Service centre

Should you contact us due to a malfunction or for placing an order, please always state the type, description and the serial number of your machine.

You can find this information on the name plate of your machine, and the address of your nearest TASKI partner can be found on the last page of this manual.

Blade replacement swingo 755B/855B

Blades replacement swingo 1255B

Blade on the inner radius

Blade on the outer radius

Cleaning or replacing the float (Indication for full recovery tank)

Disassembly:

• In order to ensure operational reliability and availability for use, the service must be carried out when the service indicatior lights up (factory setting 450 working hours) or at least once a year.

Under rough or extreme working conditions and/or insufficient maintenance, shorter periods are necessary.

• Unscrew the star grip (1), pull the blade body (2) out of the squeegee body and remove the blades (3).

• You can now turn or replace the blade.• Reinsert the blade body back into the squeegee body and screw the star

grip in place again.

3

1

2

• Place the clean squeegee unit on a solid surface (table, floor) with the rejection rollers downwards. (Detail I1)

• Loosen the screw (do not completely remove) in the middle of the 2-part tension rail until the tension rail can be removed (Detail I2).

• Clean the squeegee body, metal straps and reject roller under running water with a brush.

• Mount the "rotated" or replaced blade onto the squeegee body.• Remount the tension rail at the correct position on the lamella (Detail I3).• Tension the tension rail. (Detail I2)

• Place the clean squeegee unit on a solid surface (table, floor) with the rejection rollers downwards. (Detail A1)

• Loosen the screws (do not completely remove) on the left and right of the 3-part tension rail until the tension rail can be removed. (Detail A2)

• Clean the squeegee body, metal straps and reject roller under running water with a brush.

• Mount the "rotated" or replaced blade onto the squeegee body.• Remount the tension rail at the correct position on the lamella (Detail A3).• Tension the tension rail. (Detail A2)


• The yellow suction filter can be easily removed (quick-fit seal).

• Clean it with water using a brush (let it dry out well).

• Brush the yellow suction filter with a soft brush or remove the fluff with a cloth.

I

I2

I1

I1I3

XX<

Y

Y

AA2

A2

A1

A1

A3

XX<

Y

Y

43

I25

Malfunctions Transport

Transport the machine in an upright position and remove the batteries for transportation where necessary.

Ensure that the machine is firmly lashed down and secured in the transport vehicle.

Disposal

When it has reached the end of its operational life, the machine and its accessories must be disposed of according to the national regulations. Your TASKI partner can support you with proper disposal upon notification.

Batteries

The batteries must be removed from the machine before being disposed of properly.

Used batteries must be disposed of in an environmentally appropriate way in accordance with the EU guidelines 2006/66/EEC.

Technical data

Malfunction Possible causes Troubleshooting page

Machine does not run Maschine switched off

• Switch on the keyswitch. 37

• Connect the battery to the machine with the battery disconnection socket.

37

Battery/mains unit malfunction (display on con-trol panel)

Discharged batteries • Recharge batteries 38

Batteries/battery charger defective

• Call for technical assistence

Batteries not suf-ficiently charged

Power cord not plugged in or defecti-ve

• Plug in the power cord


Batteries or battery charging unit defecti-ve


Brush does not turn

Motor runs but not tool


Poor vacuum performance

Floor remains wet

Soiled solution not picked up

The float closes the inlet opening at the suction unit (overfill protection for recove-ry tank)

• Check the recovery tank is not full 41

• Check that the float is functioning correctly. 43

Squeegee not on the floor

• Lower the squeegee. 41

Suction hose not con-nected

• Connect suction hose

Check the seal on the tank lid for cracks/dirt

• Clean the seal, or replace if defective

Vacuum air filter blo-cked

• Remove the blockage

Hose or nozzle blo-cked (e.g. by pieces of wood or residual material)

• Remove the blockage

The blades do not ad-just well to the floor consistancy

• Clean the squeegee

• Change/turn the blades 43

• Check that the squeegee suspension is functioning correctly

Dirt sieve full (yellow)

• Remove the dirt sieve

• Knock out the coarse dirt from the sieve and rinse it under running water.

41

Vacuum switched off Recovery tank full • Empty the recovery

tank 41

Insufficient out-flow of cleaning solution

Solution tank empty • Fill the solution tank 40

Solution tank filter blo-cked

• Clean solution tank filter 42

Foam or liquid leaking from the machine

Float malfunction

• Turn off the suction aggregate 37

• Check that the float is functioning correctly. 43

Machine swingo 755

swingo 855

swingo 1255

type CO755.1/CO755.1X

CO855.1/CO855.1X

CO1255.1/CO1255.1X

Theoretical performance area operation width x drive speed (4,5) x 1000

1935 2250 2475 m2/h

Working speed 4.5 4.5 4.5 km/h

Working width 43 50 55 cm

Squeegee width 69 69 80 cm

Solution tank nominal 40 40 60 l

Recovery tank 40 40 60 l

Machine weight for operation

160 160 260 kg

Rated voltage 24V 24V 24V DC

Tools 1 x 43 1 x 50 2 x 28 cm

Brush rpm 165 165 195 min-1

Brush pressure 43 43 48 kg

Dimensions (L x W x H) 116x47.5x119.5

122x53x119.5

142x58x117 cm

Rated power 900 900 1000 W

A-weighted emission sound pressure level ISO 11201

<70 <70 <70 dB(A)

Vibrationtotal value of the Hand-Arm system ISO 5349

<0.5 <0.5 <0.5 m /s2

Splash water protection IPX3 IPX3 IPX3

Protection class without battery charger (only model: CO1255.1/CO1255.2)

III

Protection class (without battery charger). Only model: CO755.1/CO855.1

III III

Protection class with battery charger

I (II) I (II) I (II)

44

I24

I23

I22

I21

I20

I19

I18

trsv

slro

pt

pl

no

nl

ith

ufr

fies

end

ed

acz

Accessories

Dimensions of the machine

All dimensions in centimetres!

swingo 755

swingo 855

swingo 1255

Nr. Article CO755.1/CO755.1X

CO855.1/CO855.1X

CO1255.1/CO1255.1X

7510829 Driving disc Instalok 43cm 1X

8504750 Scrubbing brush 43cm nylon

1X

8504780 Scrubbing brush abrasive 43cm

1X

8504800 Scrubbing brush for washed concrete 43cm

1X


8504770 Scrubbing brush 50cm 1X


1X


1X


7510631 Scrubbing brush 28cm nylon

2X


2X


2X

8502830 Filling hose with universal water coupling

X X X

7517125 IntelliDose kit X X X

Wet battery set X X X

Different pads(Polyester brown, blue, red, and contact pad)

X X X

119.5

116

69 47.5

119.5

122

69 53

117

142

80 58

45

I25

12089-66 v006 1221 - interline brands · v006 / 12089-66 1221 i25 i24 ... (electro-smog). do not...

Documents