1759799 - key figure description for key figure does not exist in livecache sapapo_tsm298

SAP Knowledge Base Article Symptom The user receives SAP error message /SAPAPO/TSM298. The description of the message is "Key figure description for key figure <KF> does not exist in liveCache", where <KF> is a key figure with inconsistent description. Besides, you can receive a COM Error (40.134), which means that "Key figure does not exist", when loading data to a planning book in the Interactive Planning (/SAPAPO/SDP94). This error could be caused by the inconsistency with Key Figure description. Environment l SAP SCM Release Independent Reproducing the Issue The user ran consistency check /SAPAPO/TS_LCM_CONS_CHECK and found this issue in results: "Key figure description for key figure <KF> does not exist in liveCache Message no. /SAPAPO/TSM298" The consistency check doesn't repair the error. Cause The cause of this error is due to an inconsistency between the key figure description in liveCache and in the database key figure(s) of the planning area. This inconsistency is due to the fact that the key figure exists in the database but does not exists in liveCache. Resolution The first solution to this issue would be the following: l Try repair the error using /SAPAPO/TS_LCM_CONS_CHECK and the "Repair" option checked. Note 1283440 or corresponding Support Package level should be present. If consistency check cannot repair, then... l Check consistency using /SAPAPO/TS_LCM_CONS_CHECK, note down the key figures which couldn't be repaired. l Enter report /SAPAPO/TS_LCM_PAREA_CHANGE2. For the key figures in question, change one setting (e.g. disaggregation mode, accuracy). Execute changes. l Change back the settings to the previous values. Execute changes. l Double check with /SAPAPO/TS_LCM_CONS_CHECK. The key figure description should be repaired. However, this does not always repair the issue. So, if this solution does not take the desired effect, the only solution left is to do the de-initialization and re-initialization of the Planning Area. You can check the steps in the following Wiki page: http://wiki.sdn.sap.com/wiki/x/MwGCDw CAUTION: Deinitializing Planning Area will delete time series data. You should perform backup to infocube prior deinitialization. Keywords /SAPAPO/TSM298, Key figure description for key figure does not exist in liveCache, /SAPAPO/TS_LCM_CONS_CHECK, inconsistency, consistency check Header Data Product 1759799 - Key figure description for key figure does not exist in liveCache - /SAPAPO/TSM298 Version 1 Validity: 31.08.2012 - active Language English (Master) Released On 08.01.2013 22:00:52 Release Status Released to Customer Component SCM-APO-FCS-BF Basic Functions Priority Normal Category Problem Product Product Version SAP Supply Chain Management SAP Supply Chain Management 2005 SAP Supply Chain Management 2007

Upload: sergio-torres

Post on 10-Nov-2015

104 views

Category:

Documents

4 download

Report

Download

Embed Size (px):

DESCRIPTION

sap note

TRANSCRIPT

SAP Knowledge Base Article

Symptom

The user receives SAP error message /SAPAPO/TSM298. The description of the message is "Key figure description for key figure does not exist in liveCache", where is a key figure with inconsistent description.

Besides, you can receive a COM Error (40.134), which means that "Key figure does not exist", when loading data to a planning book in the Interactive Planning (/SAPAPO/SDP94). This error could be caused by the inconsistency with Key Figure description.

Environment

l SAP SCM Release Independent

Reproducing the Issue

The user ran consistency check /SAPAPO/TS_LCM_CONS_CHECK and found this issue in results:

"KeyfiguredescriptionforkeyfiguredoesnotexistinliveCache

Message no. /SAPAPO/TSM298"

The consistency check doesn't repair the error.

Cause

The cause of this error is due to an inconsistency between the key figure description in liveCache and in the database key figure(s) of the planning area. This inconsistency is due to the fact that the key figure exists in the database but does not exists in liveCache.

Resolution

The first solution to this issue would be the following:

l Try repair the error using /SAPAPO/TS_LCM_CONS_CHECK and the "Repair" option checked. Note 1283440 or corresponding Support Packagelevelshouldbepresent.Ifconsistencycheckcannotrepair,then...

l Check consistency using /SAPAPO/TS_LCM_CONS_CHECK, note down the key figures which couldn't be repaired. l Enter report /SAPAPO/TS_LCM_PAREA_CHANGE2. For the key figures in question, change one setting (e.g. disaggregation mode,

accuracy). Execute changes. l Change back the settings to the previous values. Execute changes. l Double check with /SAPAPO/TS_LCM_CONS_CHECK. The key figure description should be repaired.

However, this does not always repair the issue. So, if this solution does not take the desired effect, the only solution left is to do the de-initialization and re-initializationofthePlanningArea.YoucancheckthestepsinthefollowingWikipage:http://wiki.sdn.sap.com/wiki/x/MwGCDw

CAUTION: Deinitializing Planning Area will delete time series data. You should perform backup to infocube prior deinitialization.

Keywords

/SAPAPO/TSM298, Key figure description for key figure does not exist in liveCache, /SAPAPO/TS_LCM_CONS_CHECK, inconsistency, consistency check

Header Data

Product

1759799 - Key figure description for key figure does not exist in liveCache - /SAPAPO/TSM298

Version 1 Validity: 31.08.2012 - active Language English (Master)

Released On 08.01.2013 22:00:52 Release Status Released to Customer Component SCM-APO-FCS-BF Basic Functions Priority Normal Category Problem

Product Product Version

SAP Supply Chain Management SAP Supply Chain Management 2005

SAP Supply Chain Management 2007
References

This document refers to:

CSS SAP Notes

SAP Community Network

SAP Supply Chain Management 4.0

SAP Supply Chain Management 4.1

SAP Supply Chain Management 7.0

1283440 TS_LCM_CONS_CHECK does not repair inconsistencies

Deinitializing and reinitializing a Planning Area on SCM-APO system