2 in 2 chain maille and bead bracelet part 1
TRANSCRIPT
2 in 2 Chain Maille and Bead Bracelet Part 1
Read more at http://www.allfreejewelrymaking.com/Chain-Bracelet/2-in-2-Chain-Maille-and-Bead-Bracelet-Part-1#r2dwVS9wYAFM2DSK.99
sixty four 18 gauge 6mm OD (outside diameter) 3.5mm ID (inside diameter) unsoldered jump ringssixty four 18 gauge 6mm OD (outside diameter) 3.5mm ID (inside diameter) unsoldered jump rings
four 2 1/4 inch (5.7 cm) lengths of 20 gauge round wire four 8mm cosmojet Swarovski® crystals one toggle clasp
Jewelry Making Tools:
wire cutters round nose pliers chain nose pliers, two pair
Instructions:
1. Make a double wire loop bead unit: Using the wire cutters, cut four 2 1/4 inch (5.7 cm) lengths of 20gauge round wire.
2. Grasp one end of one wire between the jaws of your round nose pliers, about half way up the pliers' jaws.
3. Rotate the pliers forward, creating a wire loop.
4. Reposition the pliers to their original position.
5. Rotate the pliers forward, creating one and a half wire loops.
6. Reposition the pliers to their original position, grasping the top of the wire loop between the pliers' jaws.
7. Rotate the pliers forward, creating a double wire loop.
8. With the tip of the pliers, grasp the wire loop where the tip of the wire of the
first loop meets the perpendicular portion of the wire. Rotate the pliers backward about 90 degrees, creating a bend in the wire.
9. You should end up with a length of with wire that has a double wire loop on one end.
10. String one 8mm cosmojet Swarovski® crystal bead onto the wire, resting it
against the double wire loop.
11. Repeat Steps 1 - 7 on the second end of the wire. You have made one double
ended double wire loop bead unit.
12. Repeat Steps 1 - 10 to make three more double ended double wire loop bead units for a total of four.
To finish this gorgeous bracelet, check out part 2!
Read more at http://www.allfreejewelrymaking.com/Chain-Bracelet/2-in-2-Chain-Maille-and-Bead-Bracelet-Part-1#r2dwVS9wYAFM2DSK.99
four 2 1/4 inch (5.7 cm) lengths of 20 gauge round wire four 8mm cosmojet Swarovski® crystals one toggle clasp
Jewelry Making Tools:
wire cutters round nose pliers chain nose pliers, two pair
Instructions:
1. Make a double wire loop bead unit: Using the wire cutters, cut four 2 1/4 inch (5.7 cm) lengths of 20gauge round wire.
2. Grasp one end of one wire between the jaws of your round nose pliers, about half way up the pliers' jaws.
3. Rotate the pliers forward, creating a wire loop.
4. Reposition the pliers to their original position.
5. Rotate the pliers forward, creating one and a half wire loops.
6. Reposition the pliers to their original position, grasping the top of the wire
loop between the pliers' jaws.
7. Rotate the pliers forward, creating a double wire loop.
8. With the tip of the pliers, grasp the wire loop where the tip of the wire of the
first loop meets the perpendicular portion of the wire. Rotate the pliers
backward about 90 degrees, creating a bend in the wire.
9. You should end up with a length of with wire that has a double wire loop on
one end.
10. String one 8mm cosmojet Swarovski® crystal bead onto the wire, resting it
against the double wire loop.
11. Repeat Steps 1 - 7 on the second end of the wire. You have made one double ended double wire loop bead unit.
12. Repeat Steps 1 - 10 to make three more double ended double wire loop bead
units for a total of four.
To finish this gorgeous bracelet, check out part 2!
Read more at http://www.allfreejewelrymaking.com/Chain-Bracelet/2-in-2-Chain-Maille-and-Bead-Bracelet-Part-1#r2dwVS9wYAFM2DSK.99
Jewelry Making Supplies:
sixty four 18 gauge 6mm OD (outside diameter) 3.5mm ID (inside diameter) unsoldered jump rings
four 2 1/4 inch (5.7 cm) lengths of 20 gauge round wire four 8mm cosmojet Swarovski® crystals one toggle clasp
Jewelry Making Tools:
wire cutters round nose pliers chain nose pliers, two pair
Instructions:
1. To open a jump ring, grasp the jump ring on both sides of the opening in the jump ring with the jaws of two pair of chain nose pliers parallel to the opening. Rotate one of the chain nose pliers forward (towards you) and one of the chain nose pliers backward (away from you).
2. To close a jump ring, move the pliers in the opposite direction until the ends of
the jump ring meet. Leave no opening in the jump ring. In the end, well closed jump rings make neater and better looking finished jewelry.
3. Lie two closed jump rings atop one another onto your work surface. Open one jump ring.
4. Using the chain nose pliers (or your fingers), slide the two closed jump rings onto the open jump ring. Close the open jump ring.
5. Open one jump ring. Using the chain nose pliers (or your fingers), slide the
two originally closed jump rings onto the open jump ring.Close the open jump ring. You now have two pair of interconnected jump rings, hence the name 2-in-2 chain weave.
6. Repeat Steps 15 - 17, connecting two open jump rings to the last two closed
jump rings on the emerging chain until you have six (6) pairs of interconnected jump rings.
7. Open one jump ring and slide it into the sixth pair of jump rings and one of the double wire loops of a bead unit. Close the jump ring.
8. Open another jump ring and slide it into the sixth pair of jump rings and the
same double wire loop of the bead unit. Close the jump ring.
9. Open two jump rings. Slide them one at a time into the second double wire
loop of the bead unit. Close each jump ring as you go.
10. Open, connect and close four more pairs of jump rings. double wire loop of another bead unit.
11. Repeat Steps 9 and 10 with twice more. On the second double wire loop of the
last bead unit connect seven pairs of jump rings.
12. Place the unfinished bracelet around your wrist determine if you need to add
any more pairs of jump rings. The bracelet should be within 3/4 inches (1.9 cm), the length of the clasp, of your desired length.
13. On my bracelet I added one pair of jump rings, for a total of eight pairs, to each side of the chain before I attached the clasp. Open two jump rings. Slide them one at a time into the last pair of jump rings and the ring of one half of the toggle clasp. If you need to remove any pairs of jump rings, open the last pair of jump rings on one end of the chain and remove them. Remove however many pairs you need to from each side of the chain until you get a good fit.
14. If you do not need to add any pairs of jump rings to your bracelet, open the last pair of jump rings and slide them into the ring of one half of the toggle clasp. Close each jump ring as you go.
15. Repeat for the second side of the bracelet using the second half of the toggle clasp.
16. You're done.Your 2-in-2 chain maille bead bracelet is complete!
Approximately 8 inches (20.3 cm)
Read more at http://www.allfreejewelrymaking.com/Chain-Bracelet/2-in-2-Chain-Maille-and-Bead-Bracelet-Part-2#XtmPQ7XCAbaOqh9x.99