2011 11-18 standards and standardization level 1
DESCRIPTION
Delivered to undergraduate design students at De Montfort University in November 2011TRANSCRIPT
Standards and StandardizationNewell Hampson-Jones, Education Sector Representative, British Standards Institution
25th November, 2011
Produced in Collaboration with:Dr Eujin Pei, FRSADe Montfort University
2
What are standards?
3
Before Standardization
• c. 3000 BC – c. 1500 BC Indus Valley Civilization First to develop uniform weights and measures
• c. 80–70 BC – c. 15 BC Marcus Vitruvius Pollio ‘The first engineer’
• 1215 Magna Carta Clause 35 established consistent measures
4
The Birth of Standardization
• Industrial Revolution
• 1841 – Sir Joseph Whitworth
• 1850 onwards – The birth of the railways
• 1895 – Henry Skelton
• 1901 – Sir John Wolfe-BarryImage: Tom Curtis /
FreeDigitalPhotos.net
5
History of BSI
1900
2010
1946
Founder member of ISO
1929
Granted Royal Charter
1901
Engineering Standards Committee founded in London
1903
Kitemark introducedFirst StandardsBS 1 published
1931
Renamed BSI
1959
First laboratories opened
1964
Founder Member of CEN & CENELEC
6
Types of Standard
Low High
ControlTim
eInt’l
Standards
(ISO)
European Standards (EN)
Publicly Available Specifications (PAS)
Private Standards
British Standards (BS)
Corporate Technical Specifications
7
• Proposal for new work• Project acceptance• Drafting• Public Comment• Approval• Publication• Review
The Standardization Process
• European standards body
• Differences in process
• Adoption by Weighted vote
European Committee for
Standardization (CEN)
• International (global) standards body
• One member, one vote.
• Final Draft International Standard
International Organization for Standardization
(ISO)
Picture source: http://www.chinaiceberg.com/about/attachment/berg0013
Standards and
Innovation
Blind, K.., Gauch, S., (2007). “Standardization Benefits Researchers.” Wissenschaftsmanagement Special, 2007 (2), pp. 16-17
Standards and Innovative Research
Standards in the research and innovation process, by Blind & Gauch
Bakal, M., (2011). Challenges and Opportunities For The Medical Device Industry: Meeting The New IEC 62304 Standard RTC, [online] Available at:<http://rtcmagazine.com/articles/view/102203>.
Bakal’s typical stages both software and hardware teams use for analysis, design, implementation, and testing.
Using Standards to Design & Engineer
Innovation
Using Standards to Design & Engineer
Innovation
14
Testing• Snapshot in time
• Susceptible to golden sampling
• “The sample submitted complied with the requirements of EN XXXX”
Certification• More than just a
test or quality control system
• Many certification and testing bodies in the UK
• UKAS (United Kingdom Accreditation Service)
Testing and Certification
Using Standards to Design & Engineer
Innovation
CE Mark
• Conformity to New Approach Directives
• Not a quality mark
• Mandatory in the EU
• BSI cannot give authority to apply the CE marking
• It is illegal to use the CE marking on a product that is outside the scope of all the New Approach directives.
Kitemark is…• Owned exclusively by BSI
• Issued under Licence
• 3rd party voluntary mark of quality and safety
The Process• Pre-Audit visit
• Initial Assessment visit
• Type Testing of new product
• Initial assessment report
• Award of Kitemark
• Continuing assessment visits
• Audit testing
CE and the Kitemark®
Using Standards to Design & Engineer
Innovation
Source
:http
://cod
yra
pol.co
m/in
tern
et/im
ag
es/it-w
asn
t-an-ice
berg
-that-sa
nk-th
e-tita
nic/
…could Standards have saved the Titanic?
Useful Standards for Engineers
British Standards and GPS
The Controlling Standards
• BS 8887 Specification for the preparation, content and structure of design output for manufacture, assembly, disassembly and end of life processing (MADE)
• BS 8888 Technical Product Specification
• BS 8889 Contribution to specification process; data collection; decision rules; instrumentation, calibration, uncertainty / traceability.
The Elements
of an Engineering Drawing
Geometric Product Specifications
“Within BS 8888, Geometric Product Specification (GPS), provides the link between design intent and metrology. It is the international specification language that communicates component functional requirements, defines a common datum system, controls tooling, assembly, and verification interfaces, ensuring compliance with a uniform international standard. The system is:
Designed and developed by engineers for engineers A shorthand language for the engineering industry Clear, consistent, and unambiguous Applies across the entire design, manufacture and quality processes”
A language for specification and verification of technical requirements
Geometrical
Product
Specification
±0,05
30
Ø
A
-0,3
0,05 A B C
SIMn/A=10/50mm2
Ø16 H8 ( )16,02716,000GPS
• a systematic methodology
• complete and unambiguous
• covers specification and verification of workpiece geometry
• mathematically consistent
• rigorously defined
• documented in a series of interlinked ISO standards
Ø
A
-0,3
0,05 A B CSIMn/A=10/50mm216 H8 ( )16,02716,000
±0,0530
Why do we need GPS?
• With greater precision and accuracy interpretation become more significant
• CAD, CAM and CAQ systems demand formal mathematical definitions
• Globalisation
Why do we need GPS?
The British Standards Committee for GPS estimates that manufacturing industry wastes between 15% and 20% of production costs due to problems with technical product specifications. Globally, this adds up to £1.5 trillion every year.
Effective use of GPS leads to…
• improved fit and function of parts
• reduced production costs
• better quality
• better product reliability
• less scrap
• fewer disputes over compliance
• faster time-to-market
28
Name: Newell Hampson-Jones
Title: Education Sector Representative
Address: BSI
389 Chiswick High Road
London
W4 4AL
Telephone: 020 8996 7227 / 07767 886 713
Email: [email protected]
Links: www.bsigroup.com / www.bsieducation.org
Contact