3fe54967aaaatczza01_v1_7360 isam fx olt r4.4, ansi product information guide
DESCRIPTION
3fe54967aaaatczza01_v1_7360 Isam Fx Olt r4.4, Ansi Product Information Guide3fe54967aaaatczza01_v1_7360 Isam Fx Olt r4.4, Ansi Product Information Guide3fe54967aaaatczza01_v1_7360 Isam Fx Olt r4.4, Ansi Product Information GuideTRANSCRIPT
-
Alcatel-Lucent 7360INTELLIGENT SERVICES ACCESS MANAGER FX | RELEASE 04.04A N S I P R O D U C T I N F O R M A T I O N G U I D E
3FE 54967 AAAA TCZZA Edition 01
Alcatel-Lucent ProprietaryThis document contains proprietary information of Alcatel-Lucent and is not to be disclosedor used except in accordance with applicable agreements.Copyright 2012 Alcatel-Lucent. All rights reserved.
A N S I P R O D U C T I N F O R M A T I O N G U I D E
-
When printed by Alcatel-Lucent, this document is printed on recycled paper.
Alcatel-Lucent assumes no responsibility for the accuracy of the information presented, which is subject to change without notice. Alcatel, Lucent and the Alcatel-Lucent logo are registered trademarks of Alcatel-Lucent. All other trademarks are the property of their respective owners.
Copyright 2012 Alcatel-Lucent.All rights reserved.
Disclaimers
Alcatel-Lucent products are intended for commercial uses. Without the appropriate network design engineering, they must not be sold, licensed or otherwise distributed for use in any hazardous environments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft navigation or communication systems, air traffic control, direct life-support machines, or weapons systems, in which the failure of products could lead directly to death, personal injury, or severe physical or environmental damage. The customer hereby agrees that the use, sale, license or other distribution of the products for any such application without the prior written consent of Alcatel-Lucent, shall be at the customer's sole risk. The customer hereby agrees to defend and hold Alcatel-Lucent harmless from any claims for loss, cost, damage, expense or liability that may arise out of or in connection with the use, sale, license or other distribution of the products in such applications.This document may contain information regarding the use and installation of non-Alcatel-Lucent products. Please note that this information is provided as a courtesy to assist you. While Alcatel-Lucent tries to ensure that this information accurately reflects information provided by the supplier, please refer to the materials provided with any non-Alcatel-Lucent product and contact the supplier for confirmation. Alcatel-Lucent assumes no responsibility or liability for incorrect or incomplete information provided about non-Alcatel-Lucent products.However, this does not constitute a representation or warranty. The warranties provided for Alcatel-Lucent products, if any, are set forth in contractual documentation entered into by Alcatel-Lucent and its customers.This document was originally written in English. If there is any conflict or inconsistency between the English version and any other version of a document, the English version shall prevail.
-
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 iii3FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
Preface
This preface provides general information about the documentation set for the 7360 Intelligent Services Access Manager FX (7360 ISAM FX ) for ANSI.
Scope
This documentation set provides information about safety, features and functionality, ordering, hardware installation and maintenance, CLI and TL1 commands, and software installation procedures.
Audience
This documentation set is intended for planners, administrators, operators, and maintenance personnel involved in installing, upgrading, or maintaining the 7360 ISAM FX system.
Prerequired knowledge
The reader must be familiar with general telecommunications principles.
Assistance and ordering phone numbers
Alcatel-Lucent provides global technical support through regional call centers. Phone numbers for the regional call centers are available at the following URL: http://www.alcatel-lucent.com/myaccess
For ordering information, contact your Alcatel-Lucent sales representative.
-
Preface
iv May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
Safety information
See the 7360 ISAM FX Safety Manual for safety information.The following are examples of how special information is presented in this document.
Document conventions
The following conventions are used in this documentation set.
AcronymsSee the glossary for the expansion of acronyms used in this documentation set.
Release notes
See the release notes (such as the customer release notes or emergency fix release note) issued for software loads of the 7360 ISAM FX before you install or use the 7360 ISAM FX. The release notes provide important information about the software load.
Documents
Table 1 lists the documents that make up the 7360 ISAM FX documentation set.
Danger Danger indicates that the described activity or situation may result in serious personal injury or death; for example, high voltage or electric shock hazards.
Warning Warning indicates that the described activity or situation may, or will, cause equipment damage or serious performance problems.
Caution Caution indicates that the described activity or situation may, or will, cause service interruption.
Note A note provides information that is, or may be, of special interest.
-
Preface
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 v3FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
Table 1 7360 ISAM FX documentation set for ANSI
Title Description
General documentation
Product Information Provides general system and ordering information for the 7360 ISAM FX
System Description for FD 100/320Gbps NT and FX NT
Provides conceptual information for the: 7302 ISAM and the 7330 ISAM FTTN equipped with the
100Gpbs or the 320Gbps NT 7360 ISAM FX equipped with an FX NT
Safety Manual Provides general safety guidelines when handling, installing, or operating the 7360 ISAM FX equipment
Hardware documentation and unit data sheets
FX Hardware Installation Guide Describes the hardware installation for the 7360 ISAM FX equipment
UDS NFXS-D (FX-16) Describes the 7360 ISAM FX-16 slot shelf
UDS NFXS-E (FX-8) Describes the 7360 ISAM FX-8 slot shelf
UDS NFXS-F (FX-4) Describes the 7360 ISAM FX-4 slot shelf
UDS NGFC-G Describes the 7360 ISAM FX-4 general facilities card
UDS NGFC-H Describes the 7360 ISAM FX-8 general facilities card
UDS FANT-F Describes the NT card
UDS NELT-B Describes the GPON LT board (1) version B
UDS NGLT-A Describes the GPON LT board (1) version A
UDS dummy front panel FX NT Describes the dummy front panel (filler plate) for the NT card
UDS dummy front panel FX LT Describes the dummy front panel (filler plate) for the LT card
UDS AFAN-H Describes the fan unit for the 7360 ISAM FX-16
UDS AFAN-E Describes the fan unit for the 7360 ISAM FX-8
UDS AFAN-X Describes the fan unit for the 7360 ISAM FX-4
TL1 documentation
TL1 Commands and Messages for FD 100/320Gbps NT and FX NT
Describes the TL1 commands and messages for the: 7302 ISAM and the 7330 ISAM FTTN equipped with the
100Gpbs or the 320Gbps NT 7360 ISAM FX equipped with an FX NT
Operations and Maintenance Using TL1 for FD 100/320Gbps NT and FX NT
Provides task-oriented procedures using TL1 for operating and maintaining the: 7302 ISAM and the 7330 ISAM FTTN equipped with the
100Gpbs or the 320Gbps NT 7360 ISAM FX equipped with an FX NT
CLI documentation
CLI Commands for FD 100/320Gbps NT and FX NT
Describes the CLI commands for the: 7302 ISAM and the 7330 ISAM FTTN equipped with the
100Gpbs or the 320Gbps NT 7360 ISAM FX equipped with an FX NT
(1 of 2)
-
Preface
vi May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
Note(1) The term board and card are both used in the 7360 ISAM FX documentation set. Board is used
in reference to ETSI terminology, and card is used in reference to ANSI terminology.
Operations and Maintenance Using CLI for FD 100/320Gbps NT and FX NT
Provides task-oriented procedures using CLI for operating and maintaining the: 7302 ISAM and the 7330 ISAM FTTN equipped with the
100Gpbs or the 320Gbps NT 7360 ISAM FX equipped with an FX NT
IHub System Basics, Management and OAM Guide for FD 100/320Gbps NT and FX NT
Describes the IHub system basics, system management and OAM (Operations and Maintenance)
IHub Interface Guide for FD 100/320Gbps NT and FX NT
Describes the IHub system interfaces
IHub QoS Guide for FD 100/320Gbps NT and FX NT
Describes the IHub quality of service
IHub Router Configuration and Protocols Guide for FD 100/320Gbps NT and FX NT
Describes the IHub router configuration and router protocols
IHub Services Guide for FD 100/320Gbps NT and FX NT
Describes the IHub services
MPLS Guide for FD 100/320Gbps NT and FX NT
Describes the IHub MPLS services
Software documentation
Software Installation Guide Describes the software management of the 7302 ISAM, the 7330 ISAM FTTN and the 7360 ISAM FX equipment
Software Upgrade and Migration Application Procedures
Provides instructions for using the automated tools for upgrading and migrating the software for the 7302 ISAM, the 7330 ISAM FTTN and the 7360 ISAM FX
Title Description
(2 of 2)
-
Contents
Preface iiiScope ................................................................................................................... iiiAudience ................................................................................................................... iiiPrerequired knowledge................................................................................................. iiiAssistance and ordering phone numbers ........................................................................ iiiSafety information........................................................................................................ ivDocument conventions ................................................................................................. ivRelease notes .............................................................................................................. ivDocuments .................................................................................................................. iv
System and equipment overview
1 System overview 1-11.1 Introduction ............................................................................................... 1-2Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 vii3FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
1.2 Feature descriptions.................................................................................... 1-61.3 System architecture .................................................................................... 1-71.4 Network management............................................................................... 1-141.5 Equipment management ........................................................................... 1-161.6 Card capabilities and dimensioning............................................................. 1-171.7 NT redundancy support............................................................................. 1-231.8 CLEI codes............................................................................................... 1-24
2 Shelves 2-12.1 Overview ................................................................................................... 2-22.2 7360 ISAM FX shelves................................................................................. 2-2
-
Contents2.3 Supported plug-in units............................................................................... 2-72.4 Dummy front panels ................................................................................... 2-8
3 Rack mounting configurations 3-13.1 Overview ................................................................................................... 3-23.2 Rack equipment ......................................................................................... 3-23.3 7360 ISAM FX-16 rack mounting configurations ............................................ 3-33.4 7360 ISAM FX-8 rack mounting configurations .............................................. 3-53.5 7360 ISAM FX-4 rack mounting configurations .............................................. 3-8
4 Optical modules 4-14.1 Overview ................................................................................................... 4-24.2 Characteristics............................................................................................ 4-2
Planning and ordering
5 Planning the equipment 5-15.1 Overview ................................................................................................... 5-25.2 Network considerations ............................................................................... 5-25.3 Rack considerations .................................................................................... 5-45.4 Shelf considerations.................................................................................... 5-45.5 LT card considerations ................................................................................ 5-55.6 NT card considerations................................................................................ 5-55.7 V-OLT and video coupler equipment considerations....................................... 5-55.8 Installation considerations ........................................................................... 5-75.9 Power considerations ..................................................................................5-85.10 Maintenance considerations......................................................................... 5-85.11 Software licensing information..................................................................... 5-85.12 Documentation........................................................................................... 5-8
6 Ordering the equipment 6-16.1 Overview ................................................................................................... 6-26.2 Racks and mounting parts ........................................................................... 6-36.3 Shelves ...................................................................................................... 6-66.4 GFCs.......................................................................................................... 6-76.5 Fan units and fan filters .............................................................................. 6-86.6 NT card and dummy front panel .................................................................. 6-96.7 NTIO card and dummy front panel............................................................. 6-106.8 LT cards and dummy front panels .............................................................. 6-106.9 Optical modules........................................................................................ 6-116.10 Cables ..................................................................................................... 6-13
A. Mnemonics A-1A.1 Mnemonics overview...................................................................................A-2viii May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
-
ContentsGlossary
IndexAlcatel-Lucent 7360 ISAM FX R04.04 May 2012 ix3FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
-
ContentsList of figuresFigure 1-1 Basic 7360 ISAM FX network topology ........................................................ 1-3Figure 1-2 Cascading topology mode .......................................................................... 1-4Figure 1-3 Star topology mode................................................................................... 1-4Figure 1-4 Ring topology mode ..................................................................................1-5Figure 1-5 Network connections ................................................................................. 1-6Figure 1-6 7360 ISAM FX functional components ......................................................... 1-8Figure 1-7 7360 ISAM FX system components ............................................................. 1-8Figure 1-8 7360 ISAM FX forwarding architecture ........................................................ 1-9Figure 1-9 7360 ISAM FX network management ........................................................ 1-15Figure 1-10 7360 ISAM FX management topology ..................................................... 1-15Figure 2-1 7360 ISAM FX-16 shelf .............................................................................. 2-3Figure 2-2 7360 ISAM FX-8 shelf ................................................................................ 2-4Figure 2-3 7360 ISAM FX-4 shelf ................................................................................ 2-4Figure 2-4 Shelf configuration of 7360 ISAM FX-16...................................................... 2-5Figure 2-5 Shelf configuration of 7360 ISAM FX-8........................................................ 2-6Figure 2-6 Shelf configuration of 7360 ISAM FX-4........................................................ 2-6Figure 2-7 Heat and fiber management baffle for 7360 ISAM FX-16.............................. 2-7Figure 2-8 Dummy front panel for NT card.................................................................. 2-9Figure 2-9 Dummy front panel for optical LT card...................................................... 2-10Figure 2-10 Universal dummy front panel for NTIO card ............................................ 2-11Figure 3-1 Rack mounting configurations for 7360 ISAM FX-16 (3FE 66742 AB)............. 3-4Figure 3-2 Horizontal rack mounting configurations for 7360 ISAM FX-8 in an EIA
standard 19 in. rack ........................................................................... 3-6Figure 3-3 Horizontal rack mounting configurations for 7360 ISAM FX-8 in a 23 in.
rack................................................................................................... 3-7Figure 3-4 Horizontal rack mounting configurations for 7360 ISAM FX-4 in an EIA
standard 19 in. rack ........................................................................... 3-9Figure 3-5 Horizontal rack mounting configurations for 7360 ISAM FX-4 in a 23 in.
rack................................................................................................. 3-10
List of tablesTable 1 7360 ISAM FX documentation set for ANSI......................................................... vTable 1-1 Features for 7360 ISAM FX R4.3.01 .............................................................. 1-6Table 1-2 Features for 7360 ISAM FX R4.3.02 .............................................................. 1-7Table 1-3 Features for 7360 ISAM FX R4.4................................................................... 1-7Table 1-4 Supported LT cards ................................................................................... 1-10Table 1-5 Mapped items in a 7360 ISAM FX system .................................................... 1-11Table 1-6 FANT-F in 7360 ISAM FX-16....................................................................... 1-12Table 1-7 FANT-F in 7360 ISAM FX-8......................................................................... 1-12Table 1-8 FANT-F in 7360 ISAM FX-4......................................................................... 1-13Table 1-9 Manager overview ..................................................................................... 1-16Table 1-10 NT card dimensioning .............................................................................. 1-17Table 1-11 Faceplate port applicability for SyncE ........................................................ 1-18Table 1-12 IWF capabilities....................................................................................... 1-18Table 1-13 Ethernet frame size for LT cards ............................................................... 1-20x May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
-
ContentsTable 1-14 LT card dimensioning information ............................................................. 1-21Table 1-15 GPON-specific dimensioning information ................................................... 1-22Table 1-16 Total number of ports per LT card ............................................................ 1-23Table 1-17 NT Redundancy support-ready hardware modules ..................................... 1-24Table 1-18 CLEI codes.............................................................................................. 1-24Table 2-1 7360 ISAM FX shelves supported.................................................................. 2-2Table 2-2 Shelf configurations..................................................................................... 2-5Table 2-3 Mounting options/kits for 7360 ISAM FX shelves............................................ 2-7Table 2-4 Supported plug-in units in 7360 ISAM FX shelves........................................... 2-8Table 3-1 7360 ISAM FX supported rack equipment...................................................... 3-2Table 3-2 Rack mounting configurations for 7360 ISAM FX-16....................................... 3-3Table 3-3 Horizontal rack mounting configurations for 7360 ISAM FX-8.......................... 3-5Table 3-4 Horizontal rack mounting configurations for 7360 ISAM FX-4.......................... 3-8Table 4-1 Characteristics of approved optical modules .................................................. 4-2Table 5-1 Number of shelves per rack ......................................................................... 5-4Table 5-2 Ordering plug-in units and cables for the 7360 ISAM FX shelves ..................... 5-4Table 5-3 Number of LT ports per LT card ................................................................... 5-5Table 5-4 Number of NT ports per NT card .................................................................. 5-5Table 6-1 7360 ISAM FX equipment............................................................................. 6-2Table 6-2 Rack mounting configurations ...................................................................... 6-3Table 6-3 Racks ......................................................................................................... 6-3Table 6-4 FEMA level rack mounting parts for 7360 ISAM FX-16 .................................... 6-3Table 6-5 Rack mounting parts for 7360 ISAM FX-8 and 7360 ISAM FX-4 ...................... 6-4Table 6-6 Orderable 7360 ISAM FX shelves .................................................................. 6-6Table 6-7 Orderable GFCs........................................................................................... 6-7Table 6-8 Orderable fan units and filters ...................................................................... 6-8Table 6-9 Orderable NT card and NT dummy front panel .............................................. 6-9Table 6-10 Orderable NTIO dummy front panel .......................................................... 6-10Table 6-11 Orderable LT cards and LT dummy front panels......................................... 6-10Table 6-12 Orderable optical modules........................................................................ 6-11Table 6-13 Orderable CO external alarm cables .......................................................... 6-13Table A-1 Equipment mnemonics ................................................................................A-2Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 xi3FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
-
Contentsxii May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
-
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 3FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
System and equipment overview
1 System overview
2 Shelves
3 Rack mounting configurations
4 Optical modules
-
May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
-
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 1-13FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
1 System overview
1.1 Introduction 1-2
1.2 Feature descriptions 1-6
1.3 System architecture 1-7
1.4 Network management 1-14
1.5 Equipment management 1-16
1.6 Card capabilities and dimensioning 1-17
1.7 NT redundancy support 1-23
1.8 CLEI codes 1-24
-
1 System overview
1-2 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
1.1 Introduction
This chapter provides general information about the 7360 ISAM FX system including network topology, feature descriptions, system architecture, network management, equipment management, card capabilities, NT redundancy support, and CLEI code information.
Network topology
The 7360 ISAM FX system is a frame-based multi-service access platform, offering high-density fiber connections for multimedia, high-speed Internet access, voice, and business services.
Figure 1-1 shows the basic 7360 ISAM FX network topology.
-
1 System overview
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 1-33FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
Figure 1-1 Basic 7360 ISAM FX network topology
Subscriber side
At the subscriber side, each 7360 ISAM FX shelf can terminate:
Ethernet user interfaces PON interfaces
NT
EMAN
NSP IPbackbone
NSP IPbackbone
NSP IPbackbone
IP edge router/BRAS
Ethernet
DS1/E1
Video
FE/GE/10GE
FE/GE/10GE
22417
ISAM
EthernetSwitch
GPONLTONT
OMCIDS1/E1
Ethernet
Video GPONOAM
EPONEPON
LTISAM OLT
ISAM shelfISAM
EthLT FE/GE/10GE
FE/GE/10GE
EthernetONT
Note 1 Possible user interface types are not limited to the types shown in the Figure 1-1.
Note 2 A link is a term that refers to the physical layer of an interface of the 7360 ISAM FX, for example, an Ethernet link.
-
1 System overview
1-4 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
You can connect subtending DSLAMs to the FE/GE/10GE links at the subscriber side in:
cascading topology mode: a chain of one subtending ISAM per ISAM; see Figure 1-2
star topology mode: multiple subtending ISAMs per ISAM; see Figure 1-3 ring topology mode: (except when there is a ring behind a Hub-ISAM); see
Figure 1-4
Figure 1-2 Cascading topology mode
Figure 1-3 Star topology mode
k*FE/GE/10GE
ISAM
Userinterfaces
Cascading up to three levels
ISAM
k*FE/GE/10GE
Userinterfaces
ISAM
Userinterfaces
EMAN
22420
k*FE/GE/10GE
ISAM
Userinterfaces
k*FE/GE/10GE
ISAM
Userinterfaces
ISAM
Userinterfaces
EMAN
22421
-
1 System overview
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 1-53FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
Figure 1-4 Ring topology mode
Network side
At the network side, the 7360 ISAM FX terminates FE, GE, or 10GE links. Following are possible configurations.
Connect to one or more Ethernet switches.Ethernet links can be connected to one or more Ethernet switches. These Ethernet switches forward the frames over the Ethernet-based aggregation access network until they reach the IP edge router or BRAS of the corresponding NSP. At the IP edge router or BRAS, the frames enter the IP backbone of the NSP.
Connect more than one FE/GE/10GE link (link aggregation).In case of more than one link, Ethernet link aggregation is used.
Connect directly to an IP edge router.The 7360 ISAM FX can be connected directly to the IP edge router or BRAS. The Ethernet aggregation network is reduced to one or more parallel Ethernet links.
Connect to a MPLS network.
Figure 1-5 shows the 7360 ISAM FX system network connections.
ISAM
Userinterfaces
k*FE/GE/10GE
k*FE/GE/10GE
k*FE/GE/10GE
Userinterfaces
Userinterfaces
Userinterfaces
EMAN
22422
ISAM
ISAM
ISAM
-
1 System overview
1-6 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
Figure 1-5 Network connections
1.2 Feature descriptions
This section provides a brief description of the features for the 7360 ISAM FX system.
Release 4.3.01 featuresTable 1-1 describes the features for 7360 ISAM FX R4.3.01.
Table 1-1 Features for 7360 ISAM FX R4.3.01
Table 1-2 describes the features for 7360 ISAM FX R4.3.02.
EMAN
NSP IPbackbone
NSP IPbackbone
NSP IPbackbone
IP edge router/BRAS
NSP IPbackbone
Userinterfaces
FE/GE
m x FE/GE/10GE
m x FE/GE/10GE
EthernetSwitch
22423
ISAM
Userinterfaces
FE/GEISAM
Feature Description
ANSI hardware support Following is a list of ANSI-supported hardware for release 4.3.01: NFXS-D, 16-slot shelf NFXS-E, 8-slot shelf NFXS-F, 4-slot shelf FANT-F, BC variant NT card with a 480 Gbps switch NELT-B, GPON LT card version B NGLT-A, GPON LT card version A PDBP-C, GFC for the 16-slot shelf (preinstalled) NGFC-H, GFC for the 8-slot shelf NGFC-G, GFC for the 4-slot shelf AFAN-H, fan unit for 16-slot shelf AFAN-E, fan unit for 8-slot shelf AFAN-X, fan unit for 4-slot shelf
-
1 System overview
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 1-73FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
Table 1-2 Features for 7360 ISAM FX R4.3.02
Table 1-3 describes the features for 7360 ISAM FX R4.4.
Table 1-3 Features for 7360 ISAM FX R4.4
1.3 System architecture
This section describes the 7360 ISAM FX system architecture including the functional and physical components, and IHub.
Functional componentsThe 7360 ISAM FX is a multiplexer, which can be equipped with the following main cards:
NT card (optionally 1+1 redundant) NTIO card (optional) (not currently supported) LT cards implementing the user interfaces GPON LT cards
Figure 1-6 shows the 7360 ISAM FX functional components.
Feature Description
ANSI hardware support FANT-F, BD variant NT card with a 480 Gbps switch
Feature Description
ANSI hardware suppport FGLT-A, 16 port GPON LT card
NGLT-C, 8 port GPON LT card
XG-PON1 OLT XFP N1 Ctemp
XG-PON1 ONU SFP+ N2A Itemp
Note The XG-PON1 LT card is not supported in the current release. Related information is provided in the customer documentation in anticipation of their subsequent availability.
-
1 System overview
1-8 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
Figure 1-6 7360 ISAM FX functional components
The 7360 ISAM FX management plane, control plane, and most of the data plane are provided on the NT cards and on the LT cards.
Figure 1-7 shows the 7360 ISAM FX system components.
Figure 1-7 7360 ISAM FX system components
NT cards
The 7360 ISAM FX NT cards consist of an IHub subsystem and a system control subsystem.
The IHub subsystem has enhanced L2 functionality (VPLS based) and L3 functionality (VPRN based) and consists of a 10 GE switch/router device, and IHub control SW.
The system control subsystem implements the management plane of the system (both the NT cards and the LT cards) and part of the control plane (subscriber management in particular). The system control consists of SW running on a general purpose processor, shared with the IHub control SW (on a separate processor core).
ISAM
NT LT ...
NTIO LT-applique
22424
NT
iHub
System control
iHub control
Switch/Router
LT
Transport
Data plane
LT-Control
IWF
Control plane
22425
-
1 System overview
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 1-93FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
LT cards
The 7360 ISAM FX LT cards provide an IWF, a transport subsystem, and an LT control subsystem.
The transport subsystem terminates the physical layer of the user interfaces. The transport subsystem varies with the type of access technology used, such as Ethernet.
The IWF processes the packets in the fast path. The IWF is capable of handling frames at L2 (basically bridging) and L3 (basically IP forwarding), including sophisticated filtering and traffic management, all at the line rate of the transport medium.
The LT control subsystem provides the slow path control plane and internal operations and maintenance applications.
GPON LT cards
The GPON functionality of the 7360 ISAM FX extends the system boundaries up to 128 ONTs over fiber that can reach tens of kilometers from the GPON LT cards located in a 7360 ISAM FX shelf.
These GPON LT cards provide the physical interfaces from the 7360 ISAM FX shelf toward the CPE, or the ONTs.
XG-PON1 LT cards
The XG-PON1 functionality of the 7360 ISAM FX provides higher speed data rates of 10G downstream and 2.5G updstream.
Physical componentsFigure 1-8 shows the forwarding architecture of the 7360 ISAM FX system.
Figure 1-8 7360 ISAM FX forwarding architecture
A 7360 ISAM FX shelf consists of the following card types:
NT cards LT cards
IHUBrouter
Systemcontrol
IHUBcontrol
EPS
NTIO
NT LT
IWF
LTcontrol
EthernetGPONEPON
CPEONTONT
Transport
Network linksSubtending links
User links
EMAN 2 - n
22426
-
1 System overview
1-10 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
NTIO card (not currently supported) GFC card
NT cards
The shelf can accommodate two NT cards. These NT cards can act as an active/standby pair for all functions.
The FANT-F (480 Gbps) NT card is supported in 7360 ISAM FX equipment.This NT card with integrated IHub subsystem provides the following links on the front panel:
1 x fixed 10/100/1000Base-T port.This port operates in 10 Mb/s, 100 Mb/s, or 1 GE mode.
4 x 10 GE SFP+ port:This port operates in 1 GE mode (with standard SFP optics) and in 10 GE mode (with SFP+ optics).
LCMI interface (RJ-45 connector) ToD/1PPS interface (RJ-45 connector) 10 MHz GPS interface (SMA connector) 1 PPS interface (SMA connector)
LT cards
The LT cards in the shelf consist of an IWF, the transport termination, and the LT control.
The LT cards, also known as LIMs, use a different IWF between the user side and the Ethernet network side, depending on the card type. Table 1-4 lists the supported LT cards with their physical interface types, density (that is, number of lines per card), and IWF capability.
Table 1-4 Supported LT cards
Notes(1) L3: IWF capability on Layer 2 and Layer 3. For an overview of the IWF capabilities, see section 1.6.(2) Not all L3 features are supported in these ports, see Table 1-12.
LT card Physicalinterfaces
Overlay Density NT interface IWF
NELT-B Ethernet 36 10 GE L3 (1)
FGLT-A GPON 16 40 GE L3 (1) (2)
NGLT-A GPON 8 10 GE L3 (1) (2)
NGLT-C GPON 8 20 GE L3 (1) (2)
-
1 System overview
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 1-113FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
GFC card
The GFC provides connections for external power, circuit breakers for system protection, visual indications for power availability, and collection and cascading of external alarms.
NTIO card
The 7360 ISAM FX NTIO card plays the role of an applique to a single NT card, or to both NT cards, dependant on the NT redundancy configuration. The NTIO card can decouple NT equipment protection from up-link protection in case of a redundant NT pair. If the active NT fails, traffic on the NTIO external links will be switched automatically to and from the standby NT.
Port mapping
The following tables list the port mapping for the 7360 ISAM FX system, that is, the mapping between the logical port numbers as used in the system and the physical port numbers as visible on the equipment (front panel numbering). Table 1-5 lists the mapped items in a 7360 ISAM FX system. Table 1-6 lists the port mapping for the FANT-F card in a 7360 ISAM FX-16
shelf. Table 1-7 lists the port mapping for the FANT-F card in a 7360 ISAM FX-8 shelf. Table 1-8 lists the port mapping for the FANT-F card in a 7360 ISAM FX-4 shelf.
Table 1-5 Mapped items in a 7360 ISAM FX system
Note These cards are only used on the 7360 ISAM FX-8 and the 7360 ISAM FX-4.
Item Description
Physical port number Physical switch device port number
Logical port number Port number as denoted in the SNMP management interface
LT port number (index based)
For internal LT ports, the index of the LT in the main shelf that corresponds to this port (for local LTs only)
Front panel port number For external ports, how this port is identified at the front panel of the card
Port state / configurability For NTIO ports, how this port can be configured: UP for uplinks/subtending/user links DOWN for internal LT links FIXED for fixed configuration (UP or DOWN) CONF for configurable configuration (UP or DOWN)
-
1 System overview
1-12 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
Table 1-6 FANT-F in 7360 ISAM FX-16
Table 1-7 FANT-F in 7360 ISAM FX-8
Physical port number
Logical port number
LT slot number(index based)
Faceplateport number
Interface
10 15 1
12 16 2
16 17 3
18 18 4
32 19 5
34 20 6
41 21 7
43 22 8
45 23 9
37 24 10
22 25 11
8 26 12
39 27 13
28 28 14
20 29 15
17 30 16
2 5 1 (NT-A) RJ-45
4 6 X1 (NT-A) SFP+
5 7 X2 (NT-A) SFP+
6 8 X3 (NT-A) SFP+
7 9 X4 (NT-A) SFP+
3 3 IEEE1588 (NT-A)
10 1 (NT-B) RJ-45
11 X1 (NT-B) SFP+
12 X2 (NT-B) SFP+
13 X3 (NT-B) SFP+
14 X4 (NT-B) SFP+
4 IEEE1588 (NT-B)
Physical port number
Logical port number
LT slot number(index based)
Faceplateport number
Interface
10 15 1
12 16 2
(1 of 2)
-
1 System overview
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 1-133FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
Table 1-8 FANT-F in 7360 ISAM FX-4
16 17 3
18 18 4
32 19 5
34 20 6
41 21 7
43 22 8
2 5 1 (NT-A) RJ-45
4 6 X1 (NT-A) SFP+
5 7 X2 (NT-A) SFP+
6 8 X3 (NT-A) SFP+
7 9 X4 (NT-A) SFP+
3 3 IEEE1588 (NT-A)
10 1 (NT-B) RJ-45
11 X1 (NT-B) SFP+
12 X2 (NT-B) SFP+
13 X3 (NT-B) SFP+
14 X4 (NT-B) SFP+
4 IEEE1588 (NT-B)
Physical port number
Logical port number
LT slot number(index based)
Faceplateport number
Interface
10 15 1
12 16 2
16 17 3
18 18 4
2 5 1 (NT-A) RJ-45
4 6 X1 (NT-A) SFP+
5 7 X2 (NT-A) SFP+
6 8 X3 (NT-A) SFP+
7 9 X4 (NT-A) SFP+
3 3 IEEE1588 (NT-A)
10 1 (NT-B) RJ-45
11 X1 (NT-B) SFP+
12 X2 (NT-B) SFP+
(1 of 2)
Physical port number
Logical port number
LT slot number(index based)
Faceplateport number
Interface
(2 of 2)
-
1 System overview
1-14 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
IHub
The IHub provides L2 bridging (based on VPLS) and IP routing (based on VPRN). The IHub has at least 28 ports with various specializations.
A number of ports are used to make a connection at 1 Gb/s or at 2.5 Gb/s or at 10 Gb/s to an LT local in the shelf (one IHub link per LT). The connection speed depends on the LT capabilities; see Table 1-4.
The FE/GE ports, which are not used for connecting LT cards (local or remote), and the 10GE ports, are available as network interfaces, interfaces to subtended DSLAM systems, or for connecting directly to users. These links serve network links, subtending links, or user links respectively.
Use of these ports is possible through:
link interfaces that are physically located on an NTIO card, connected via bidirectional P2P high-speed connections on the backplane to both NT cardsThese interfaces can also be used as electrical FE or GE interfaces, or optical GE, or 10GE interfaces, for uplink, subtending, or user links. The NTIO card contains an NT equipment protection switch per external link interface.Link protection and NT equipment protection can be performed independently from each other for links terminated on the NTIO.
link interfaces that are physically located on the NT card, as electrical FE or GE interfaces, or optical GE or 10 GE interfaces, for uplink, subtending, or user links.
1.4 Network management
This section provides network management information for the 7360 ISAM FX system.
Figure 1-9 shows how the 7360 ISAM FX system can be managed in a network.
13 X3 (NT-B) SFP+
14 X4 (NT-B) SFP+
4 IEEE1588 (NT-B)
Physical port number
Logical port number
LT slot number(index based)
Faceplateport number
Interface
(2 of 2)
-
1 System overview
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 1-153FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
Figure 1-9 7360 ISAM FX network management
The remote craft terminal (CT) uses TL1 commands or command line interface (CLI) commands. TL1 is used for pre-provisioning of the NT cards. CLI is used to manage both the xHub subsystem and the IACM.
Figure 1-10 shows the management topology for the 7360 ISAM FX.
Figure 1-10 7360 ISAM FX management topology
The NT controller and the xHub subsystem each contain a separate SNMP agent. These can be managed using an element management station (EMS), such as the Alcatel-Lucent 5520 AMS.
It is also possible to use a local TL1 or CLI craft terminal on the NT card to manage the LT cards.
An integrated CLI approach is implemented on the NT card using a CLI agent. This agent implements CLI commands for the NT controller / LIMs and the xHub subsystem. However, there is no semantic integration.
Table 1-9 shows an overview of the involved managers.
20768
Remote CTCLI (via Telnet)
TL1 (via UDP-login)CTEMS RS232
ISAM
LIM
LIM
LIM
IACM
xHubNetwork Ports
Management Flowto cascaded ISAM
EMAN
20767
TL1agent
TL1 TerminalTL1 Gateway TL1 CTEMS(e.g. AMS 5520) CLI Terminal CLI CT
CLIagent
Debug Terminal
Debugagent
SNMPv2or
SNMPv3
UDP UDPSSH SSH TelnetRS232 RS232
SNMPagent ISAM
-
1 System overview
1-16 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
Table 1-9 Manager overview
1.5 Equipment management
This section describes the 7360 ISAM FX general equipment practice including CO equipment management, SyncE support, IWF capabilities, Ethernet frame size, dimensioning information, and OLT service and system capacity.
The NE equipment practice type does not have to be explicitly planned by the operator, but is auto-planned by the NT at startup, depending on the detected type. At the same time, the NT will auto-plan the maximum number of racks supported by this equipment practice. The following 7360 ISAM FX type is defined:
LNWW: large new equipment practice worldwide market (6 racks, 4 shelves per rack)
Shelves are automatically planned upon detection. The operator can control the administrative state of a shelf (lock/unlock).The NE manages different types of cards. A complete overview of all supported card types in each type of shelf is in the chapter 2 Shelves. Card planning is supported for all types of cards, including the appliques. For LSMs, the operator can control the administrative state (lock/unlock).
CO equipment managementCO equipment only supports configurations consisting of a single rack and shelf.
ONT managementFor more information about the ONT management, see System Description for FD 100/320Gbps NT and FX NT.
Type Description
EMS Element management system (EMS) based on SNMP. The Alcatel-Lucent work station (5520 AMS) is commonly used.
CT Craft terminal using TL1 commands or command line interface (CLI) commands.
Note 1 External OAM VLAN:
The IHub subsystem supports in-band management. This happens through a dedicated VLAN, which must be configured (if different than 4093) on both the IHub subsystem as on the NT.Note 2 VLAN 4094 is reserved for internal communication and cannot be used in any Ethernet network in which the 7360 ISAM FX system is deployed.
-
1 System overview
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 1-173FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
1.6 Card capabilities and dimensioning
This section provides an overview of:
dimensioning information for the NT cards; see Table 1-10 SyncE support on NT cards and NTIO cards; see Table 1-11 the IWF capabilities of the LT cards per forwarding type; see Table 1-12 Ethernet frame size; see Table 1-13 dimensioning information of the LT cards per forwarding type; see Table 1-14 GPON-specific dimensioning; see Table 1-15
NT card dimensioningTable 1-10 lists the dimensioning for the NT cards and their variants.
Table 1-10 NT card dimensioning
Description FANT-F
Throughput 480 Gbps
Maximum number of MAC addresses (FDB)(1) 128 k
Maximum number of IP interfaces 512
ARP table size IPv4 16 k
IPv6 8 k
Maximum number of IP routes: IPv4 FIBRIB
16 k16 k
IPv6 FIBRIB
8 k8 k
Maximum number of L2 filters 512(2)
Maximum number of L3 filters 512
Maximum number of VLANs 4 k
Maximum number of cross-connects 4 k
Maximum number of ONTs 16
Maximum number of UNIs 19584
Maximum number of VLAN ports 103680
Maximum number of CC VLAN 49152
Maximum number of (active) MC streams 2 k
Maximum number of L2-terminated VLAN 3072
L2 frame size (in bytes) 2048
External interfaces 1 x El. GE4 x 1/10 GE
BITS in/out ports 1/1
SyncE input/output 4/4
(1 of 2)
-
1 System overview
1-18 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
Notes(1) A number of MAC addresses are always used by the system for internal purposes.(2) The same resource is shared for L2 filters and L3 filters. So, the maximum cannot be obtained for
both at the same time.
SyncE supportTable 1-11 lists the port applicability of the SyncE NTR functionality for clock extraction (in) and generation (out).
Table 1-11 Faceplate port applicability for SyncE
IEEE 1588v2 PTP supportThe IEEE 1588v2 precise time protocol provides an upgraded architecture to improve syncronization accuracy and allow precise ToD information to be distributed within the NT and LT cards in a 7360 ISAM FX shelf. The ToD serial output and 1PPS signals are processed by the NT cards and are distributed to the LT cards through the backplane signals of the 7360 ISAM FX system to allow the collection of precise ToD information that can be measured on both the ToD/1PPS interface on the NT card, and on the system backplane.
IWF capabilitiesTable 1-12 lists the IWF capabilities of the LT cards. See Table 1-4 for an overview of the supported LT cards.
Table 1-12 IWF capabilities
IEEE1588 slave for frequency synchronization Y
Description FANT-F
(2 of 2)
Card Port SyncE in support SyncE out support
FANT-F X1 1 GE and 10 GE 1 GE and 10 GE
X2 1 GE and 10 GE 1 GE and 10 GE
X3 1 GE and 10 GE 1 GE and 10 GE
X4 1 GE and 10 GE 1 GE and 10 GE
Feature L3 L3GPON
NELT-B
UNI NNI
ATM AAL5 encapsulation type
LLC/SNAP bridged (IPoE and PPPoE) Y
LLC/SNAP routed (IPoA) Y
LLC/NLPid (PPPoA) Y
(1 of 3)
-
1 System overview
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 1-193FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
VC Mux bridged (IPoE and PPPoE) Y
VC Mux routed (IPoA) Y
VC Mux PPPoA (PPPoA) Y
Encapsulation autodetect
Auto-detect IP (between LLC/SNAP bridged and routed) Y
Auto-detect PPP (between LLC/SNAP bridged, VC Mux bridged and LLC-NLPID, VC Mux PPPoA)
Y
Auto-detect IP+PPP Y
Auto-detect PPPoA (between LLC-NLPID and VC Mux PPPoA) Y
Bridged encapsulation Ethernet packet formats
Reception of untagged packets Y Y Y
Reception of combination of untagged and priority-tagged packets Y Y Y
Reception of single-tagged packets Y Y Y Y
Reception of combination of untagged, priority-tagged, single-tagged packets
Y Y Y Y
Packet processing
Port-based default VLAN for untagged/priority-tagged (if applicable) packets
Y Y Y Y
Port- and protocol-based default VLAN for untagged/priority-tagged packets of the IpoE protocols
Y Y Y Y
Port- and protocol-based default VLAN for untagged/priority-tagged packets of the PPPoE protocols
Y Y Y Y
Priority-bit re-marking and mapping table for tagged/priority-tagged packets
Y Y Y Y
L2 Forwarding
RB mode: protocol filter (set of Ethertypes) for upstream traffic in VLANs in (PPPoE and IpoE)
Y Y Y Y
RB mode Ethernet packet types: Ethernet II encap on Ethernet Y Y Y Y
RB mode Ethernet packet types: LLC/SNAP on Ethernet Y Y Y Y
CC mode: transparently pass all encapsulations (for example, PPPoE and IpoE)
Y Y Y Y
CC mode: protocol filter Y Y Y
CC mode: IPoA to IPoE CC Y
VLAN stacking (S-VLAN CC and S-VLAN/C-VLAN CC) Y Y Y Y
VLAN stacking (S-VLAN/C-VLAN residential bridge)
QoS-aware CC Y
L2 Forwarding user access protocols
ARP: enabling/disabling broadcast Y Y Y
802.1X authentication Y Y Y
Feature L3 L3GPON
NELT-B
UNI NNI
(2 of 3)
-
1 System overview
1-20 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
Notes(1) IP aware bridge is only supported on L3 LT cards with 1GE NT interface; not on L3 LT cards with 2.5GE NT interface GPON
LT cards and NELT-B(2) Support policing on bridge port on L2.
Ethernet frame sizeTable 1-13 lists the supported Ethernet frame size for the LT cards.
Table 1-13 Ethernet frame size for LT cards
DHCP option 82 insertion Y Y Y
PPPoE relay tag Y Y Y
PPPoA-PPPoE relay Y
Multicast services access control Y Y Y
Multicast services resource control Y Y Y Y
L3 Forwarding
IPoE (1) Y Y Y
IPoA (1) Y Y Y
VLAN termination (at network side), forwarding at Layer 3 Y Y Y
L3 Forwarding user access protocols
802.1X authentication Y Y
ARP proxy user side for IPoE Y Y
DHCP relay Y Y
QoS
CAC profile Y Y Y Y
Association of QoS profiles to ports Y (2) Y Y Y
Association of QoS profiles to port-VLAN associations Y Y Y Y
Sub-flow counters Y
Feature L3 L3GPON
NELT-B
UNI NNI
(3 of 3)
LT card Encapsulation Frame size (bytes)
P2P Ethernet NELT-B UNI (with FCS) 1976
NELT-B NNI (with FCS) 2048
OLT FGLT-A (with FCS) 2000
OLT NGLT-A (with FCS) 2000
OLT NGLT-C (with FCS) 2000
-
1 System overview
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 1-213FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
Dimensioning of the LT cardsTable 1-14 lists the dimensioning information for the LT cards. See Table 1-4 for an overview of the supported LT cards.
Table 1-14 LT card dimensioning information
Feature L3 L3 GPON NELT-B
UNI NNI
General
Maximum number of PONs (2) 816
Maximum number of UNIs 4096
Maximum number of FE ports per card 36 36
Maximum number of GE ports per card 36 36
Maximum number of UNI port type (FE) per card
36
Maximum number of UNI port type (GE) per card
36
Maximum number of NNI port type (FE) per card
36
Maximum number of NNI port type (GE) per card
36
Maximum number of CC VLAN 768 11 520 4608 4608
Maximum number of RB VLAN 768 1296 1296 1296
Maximum number of VLAN per PVC 16 8
Maximum number of port-VLAN associations per LT
384 11 520 144 4608
Maximum number of VLAN port per UNI (FE/GE)
8
Maximum number of VLAN port per NNI (FE/GE)
256
Maximum number of MAC addresses per VLAN port
64 64
Maximum number of MAC addresses per UNI
64
Maximum number of MAC addresses per NNI
3072
Maximum number of MAC addresses per LT (including static)
1024 16 K(1) 2304 32768
Maximum number of user IP addresses per LT (including static)
384 8 K
Average number of IPv4 subnets or addresses per card (=Average IP anti-spoofing entries, full/32 IP address or subnet, per card
288 0
Maximum number of IPv4 hosts per card 288 0
(1 of 2)
-
1 System overview
1-22 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
Notes(1) A few MAC addresses are used by the system for internal purposes.(2) Dependant on variant of LT card; NGLT-A/NGLT-C:8, FGLT-A:16.
ISAM OLT service and system capacityThis section provides information about the 7360 ISAM FX service and system capacities, and ISAM OLT performance, distance, and connection capacities.
Service and system capacities
Table 1-15 lists dimensioning information specific to the GPON functionality.
Table 1-15 GPON-specific dimensioning information
Maximum number of IPv6 subnets or addresses per UNI
16 0
Maximum number of IPv6 subnets or addresses per VLAN port
4 0
Maximum number IPv6 host addresses per card
288 0
Maximum number of VRFs per LT 128 N\A
Multicast dimensioning
Maximum number of simultaneous multicast channels per LT
1024 1024 1024 1024
Maximum number of multicast groups per user
100 100 100 1024
Maximum number of multicast VLANs 128 64
802.1x
Maximum number of 802.1x sessions per PON
288
Maximum number of 802.1x sessions per UNI
1
Maximum number of 802.1x sessions per card
2304 36
Feature L3 L3 GPON NELT-B
UNI NNI
(2 of 2)
Feature L3 GPON
Maximum number of ONT per PON 128
Maximum number of UNIs per PON 288
Maximum number of TCONTs per PON 1024
Maximum number of GEM ports per PON 2048
-
1 System overview
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 1-233FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
ISAM OLT performance and distance
The P-OLT provides performance and distance capacity of 2.488 Gb/s downstream and 1.244 Gb/s upstream, within a 30 km (18.6 mi) span, for all NGLT cards. The optical link budget is defined by both loss and bandwidth characteristics. The loss characteristic is determined by the difference between the optical transmitter and optical receiver for each direction, and is typically 28 dB. The bandwidth characteristic is determined by the maximum link distance parameter of each OLT and ONT transmitter specification, and is limited by the smaller of the upstream and downstream values.
ISAM OLT connection capacities
The ISAM OLT can accommodate a maximum of 16 LT cards. The number of ports depends on the LT card used. Table 1-16 describes the total number of ports per LT card.
Table 1-16 Total number of ports per LT card
1.7 NT redundancy support
Four levels of redundancy are supported:
link redundancy equipment redundancy subscriber line redundancy application redundancy
NT redundancy implements link redundancy and equipment redundancy in a decoupled architecture, which results in the following redundancy cases:
only link protection:single NT, active-standby, or load-sharing uplinks
combined NT and link protection, no NTIO:dual active/standby NT, with direct uplink or link set
decoupled NT and link protection, single NTIO:dual active/standby NT, NTIO card with link switches
NT protection, passive link protection, no NTIO:single, active-standby or load sharing uplinks
subtending system protection
Table 1-17 lists the hardware modules that are ready for NT redundancy support.
Card type Number of ports per card
Totalnumber of ports
FGLT-A 16 256
NGLT-A 8 128
NGLT-C 8 128
-
1 System overview
1-24 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
Table 1-17 NT Redundancy support-ready hardware modules
1.8 CLEI codes
This sections provides the currently available CLEI codes.
Table 1-18 lists the cards and fan units for which CLEI codes are available.
Table 1-18 CLEI codes
Type Module
Shelf NFXS-DNFXS-ENFXS-F
NT cards FANT-F
LT cards NELT-B
NGLT-A
NGLT-C
FGLT-A
Caution The CLEI code changes whenever an item change (that is, an adaptation to a card) occurs.The latest status of these CLEI codes is always available on the following website:
https://codecenter.commonlanguage.com/applogin.asp?app=clei_inquiry
An account is required before the CLEI database can be accessed.
Mnemonic Variant CLEI code CPR Bar code
AFAN-E 3FE 65060 AA VAUCAJ86AA 072AXJ 178692
AFAN-H 3EC 37533 NB VAUCAE2KAA 070LXX 154967
AFAN-X 3FE 64994 AA VAUCAJ56AA 072ARC 178361
FANT-F 3FE 53701 BD VAI2AHVNAA 072DJP 182107
FGLT-A 3FE 66721 AA
NELT-B 3FE 62543 AA VAUCAJ36AA 072AEY 177909
NFXS-D 3FE 65209 BA VAMZ600BRA 215138 463997
NFXS-E 3FE 64936 BA VAMZ400BRA 215136 463993
NFXS-F 3FE 64991 BA VAMZ500BRA 215137 463996
NGFC-G 3FE 65676 AA VAUCAK26AA
NGFC-H 3FE 65675 AA VAUCAK36AA
(1 of 2)
-
1 System overview
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 1-253FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
NGLT-A 3FE 64279 AA VAI2AFHDAA 070YVT 175498
NGLT-C 3FE 67301 AA
Mnemonic Variant CLEI code CPR Bar code
(2 of 2)
-
1 System overview
1-26 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
-
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 2-13FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
2 Shelves
2.1 Overview 2-2
2.2 7360 ISAM FX shelves 2-2
2.3 Supported plug-in units 2-7
2.4 Dummy front panels 2-8
-
2 Shelves
2-2 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
2.1 Overview
This chapter provides information about the different 7360 ISAM FX shelves supported for ANSI.
2.2 7360 ISAM FX shelves
This section provides general information about the 7360 ISAM FX shelf types, shelf configurations, NT redundancy, fan unit, baffles, and drip tray.
The modular organization of the 7360 ISAM FX system allows a wide range of physical size and traffic capacity options.
The basic building blocks of the 7360 ISAM FX system are the shelves. The 7360 ISAM FX system for R4.x is a one-shelf system. Daisy-chaining multiple shelves using extender cards is not supported.
Multiple collocated shelves can be cascaded using the standard FE, GE, and 10 GE subtending links. In such a configuration, each shelf operates and is managed as a separate system.
Shelf types
Table 2-1 lists the 7360 ISAM FX shelves supported.
Table 2-1 7360 ISAM FX shelves supported
Note(1) Specific mounting kits must be used. See Table 2-3 for mounting kit requirements.
Figure 2-1 shows the 7360 ISAM FX-16 shelf.
Item Shelves
7360 ISAM FX-16
7360 ISAM FX-8
7360 ISAM FX-4
Code 3FE 65209 BA 3FE64936 BA 3FE-64991 BA
Mnemonic NFXS-D NFXS-E NFXS-F
Dimensions Width 529 mm20.83 in.
482.5 mm19.00 in.
482.5 mm19.00 in.
Height 622.5 mm24.51 in.
355 mm13.98 in.
222 mm8.74 in.
Depth max. 280 mm11.02 in.
278.3 mm10.96 in.
278.3 mm10.96 in.
Can be mounted in: 19 in. EIA standard racks
N Y(1) Y(1)
23 in. racks Y(1) Y(1) Y(1)
-
2 Shelves
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 2-33FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
Figure 2-2 shows the 7360 ISAM FX-8 shelf.
Figure 2-3 shows the 7360 ISAM FX-4 shelf.
Figure 2-1 7360 ISAM FX-16 shelf
ALM Energy Hazard
01 02 03 04 05 06 07 08 NTA NTIO NTB 09 10 11 12 13 14 15 16
Card cagearea
Power unit and cable connection
area
Fan unit
General functionand control unit
22120
7360 ISAM FX-16
N594
R T HAE
BO
N
DI N G P
O
I NT
ESD
ON
OFF
A/70 FOR LT
ON
OFF
B/70 FOR LT-48V 70A
Energy Hazard BAT ABAT B
ACO
CRITICAL
MAJOR
MINOR
BITS INTERFACE TIME OF DAY1 Hz-PULSE
NT-A NT-BRINGTIPFRAME GND
CO ALARMSCRAFT PORT
TB1-2 B
AT RTN A
TB1-3 B
AT RTN B
TB1-1 -4
8V BAT A
TB1-4 -4
8V BAT B
-
2 Shelves
2-4 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
Figure 2-2 7360 ISAM FX-8 shelf
Figure 2-3 7360 ISAM FX-4 shelf
Shelf configurations
Table 2-2 lists the shelf configurations.
N594
FAN
NTA
NTIO
NTB
0102
0304
0506
0708
7360
ISAM
FX-
8
Energy HazardCritical
Alarms
ACOBAT ARemote CraftBITSExternal Alarms
MajorMinor
BAT B
7360 ISAM FX-8B-40A
A-40ANTA GND NTB
21957
Cardcage
General facilities card Fan unit
FAN
NTA
NTI
ON
TB01
0203
04
22436
7360
ISAM
FX-4
TOD/IHZ Critical AlarmsFUSEBAT ARemote CraftBITSExternal Alarms
NTA GND NTB
Major ACO1A B
23 Minor
BAT BN594
7360 ISAM FX-4
Cardcage
General facilities card Fan unit
-
2 Shelves
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 2-53FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
Table 2-2 Shelf configurations
The following figures show the general layout and the slot numbering for the 7360 ISAM FX shelves:
Figure 2-4 shows the 7360 ISAM FX-16.
Figure 2-5 shows the 7360 ISAM FX-8.
Figure 2-6 shows the 7360 ISAM FX-4.
Figure 2-4 Shelf configuration of 7360 ISAM FX-16
Configuration 7360 ISAM FX-16 7360 ISAM FX-8
7360 ISAM FX-4
Maximum number of LT cards 16 8 4
Maximum number of NT cards 2 2 2
Maximum number of NTIO cards 1 (optional) 1 (optional) 1 (optional)
Fan unit
CBs, LEDs and switches
Connectors
LT1
LT2
LT3
LT4
LT5
LT6
LT7
LT8
NTA
NTIO NTB
LT9
LT10
LT11
LT12
LT13
LT14
LT15
LT16
22131
-
2 Shelves
2-6 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
Figure 2-5 Shelf configuration of 7360 ISAM FX-8
Figure 2-6 Shelf configuration of 7360 ISAM FX-4
NT redundancyThe protection scheme for NT redundancy is 1+1 (active/active) in the data plane, and 1:1 (active/standby) in the control and management plane.
Fan unitOne fan unit provides forced air cooling in the shelf.
The fan unit is a field-replaceable unit in the shelf fan area and plugs directly into the backplane. The fan unit can be equipped with a fan filter.
Shelf mounting kits
The mounting kits required for installation of 7360 ISAM FX-16 shelves are included with the shipment. The number of kits provided depends on the rack mounting configuration required, with either one or two shelves. Baffle kits, mounting bracket kits, and the required screws are all included.
Specific mounting kits may be required for installation of the 7360 ISAM FX-8 and 7360 ISAM FX-4 shelves, depending on the rack mounting configuration.
LT 7LT 6LT 5LT 4LT 3LT 2LT 1
NT ANT I/ONT B
NGFC-H
FAN
LT 8
21959
LT 4LT 3LT 2LT 1
NT ANT I/ONT B
NGFC-G
FAN
22406
-
2 Shelves
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 2-73FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
Table 2-3 describes the mounting options and mounting kits available. See the 7360 ISAM FX Hardware Installation Manual for more information.
Table 2-3 Mounting options/kits for 7360 ISAM FX shelves
Heat and fiber management baffle
A heat and fiber management baffle is installed with the 7360 ISAM FX-16 shelf for safety protection from heat, possible flame spread, and loose particles that may cause damage to equipment. Factory-installed fiber optic cabling ring-guides are used for proper fiber optic cable handling. See Figure 2-7.
Figure 2-7 Heat and fiber management baffle for 7360 ISAM FX-16
2.3 Supported plug-in units
Table 2-4 lists the supported plug-in units in the 7360 ISAM FX shelves.
Type of rack / mount 7360 ISAM FX-4 7360 ISAM FX-8
19 in. EIA rack with horizontal mount
Shelf mounting kit optionalIncludes: mounting brackets -not
required mounting screws -required
Shelf mounting kit optionalIncludes: mounting brackets -not
required mounting screws -required
23 in. rack with horizontal mount
Shelf mounting kit requiredIncludes: mounting brackets
-required mounting screws -required
Shelf mounting kit requiredIncludes: mounting brackets
-required mounting screws -required
22373
-
2 Shelves
2-8 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
Table 2-4 Supported plug-in units in 7360 ISAM FX shelves
2.4 Dummy front panels
This section describes the 7360 ISAM FX shelf dummy panels (filler plates) for NT cards, optical LT cards, and NTIO cards.
Dummy front panels must be mounted on any unused slot of a shelf to ensure:
EMC compliance thermal compliance via a correct airflow in the shelf safety by avoiding direct contact with backplane connectors
When a slot is provisioned, the dummy front panel is replaced by the appropriate card and the cables are connected to the card.
For NT cardsA dummy front panel must be used when the second NT card is not installed. Figure 2-8 shows the dummy front panel for an NT card.
Slot Plug-in Unit Description
NTA FANT-F 480 Gbps NT card
NTB FANT-F 480 Gbps NT card
LT slot NELT-B 36-line Ethernet (FE/GE) LT card
NGLT-A GPON LT card with 8 GPON interfaces
NGLT-C GPON LT card with 8 GPON interfaces
FGLT-A GPON LT card with 16 GPON interfaces
General facilities card NGFC-G GFC for 7360 ISAM FX-8 shelf
NGFC-H GFC for 7360 ISAM FX-4 shelf
Fan area AFAN-H NB Fan unit for 7360 ISAM FX-16 shelf
AFAN-E Fan unit for 7360 ISAM FX-8 shelf
AFAN-X Fan unit for 7360 ISAM FX-4 shelf
Note For more information about the plug-in units, see the relevant UDS. The mnemonics that are used are explained in Appendix A.
-
2 Shelves
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 2-93FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
Figure 2-8 Dummy front panel for NT card
For optical LT cardsA dummy front panel must be used when an LT card is not installed (NGLT-A, NGLT-C, FGLT-A). Figure 2-9 shows the dummy front panel for optical LT cards.
22197
XX
XX
XX
XX
XX
XX
X
-
2 Shelves
2-10 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
Figure 2-9 Dummy front panel for optical LT card
For NTIO cardA dummy front panel must be used when the NTIO card is not installed. Figure 2-10 shows the universal dummy front panel for an NTIO card.
Dust cap
22198
-
2 Shelves
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 2-113FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
Figure 2-10 Universal dummy front panel for NTIO card
22429
-
2 Shelves
2-12 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
-
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 3-13FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
3 Rack mounting configurations
3.1 Overview 3-2
3.2 Rack equipment 3-2
3.3 7360 ISAM FX-16 rack mounting configurations 3-3
3.4 7360 ISAM FX-8 rack mounting configurations 3-5
3.5 7360 ISAM FX-4 rack mounting configurations 3-8
-
3 Rack mounting configurations
3-2 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
3.1 Overview
This chapter describes the rack equipment and the supported rack mounting configurations for the following 7360 ISAM FX shelves:
7360 ISAM FX-16 7360 ISAM FX-8 7360 ISAM FX-4
3.2 Rack equipment
This section briefly describes the 7360 ISAM FX rack equipment and assembly.
The rack equipment can be delivered as a pre-assembled rack or in separate kits.
The rack assembly includes a rack, shelves, accompanying fan units, baffles, and drip tray assembly kits. Each rack configuration is ordered with a specific ordering code. The 7360 ISAM FX-16 rack mounting configurations include the rack, however, the racks are optional for the 7360 ISAM FX-8 and 7360 ISAM FX-4 rack mounting configurations. See Chapter 6 for ordering information.
Parts can also be delivered separately or in kits, where the assembly is done on site at the customer location.
Table 3-1 lists the 7360 ISAM FX system rack equipment that can be used, dependent on the rack configuration required and currently supported.
Table 3-1 7360 ISAM FX supported rack equipment
For more information about 7360 ISAM FX equipment and the supported racks and rack mounting configurations, see the 7360 ISAM FX Hardware Installation Manual.
Note 1 See chapter 6 for part numbers.
Note 2 See 7360 ISAM FX Hardware Installation Manual for more information about how to install the equipment.
Size of rack Shelf apeture between rack uprights
EIA standard 19 in. rack 17.75 in. (450.9 mm)
23 in. rack 21.5 in. (546.1 mm)
-
3 Rack mounting configurations
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 3-33FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
3.3 7360 ISAM FX-16 rack mounting configurations
This section describes the 7360 ISAM FX-16 rack mounting configurations.
The 7360 ISAM FX-16 can be installed vertically in a 23 in. rack.
Table 3-2 lists the supported rack configurations for the 7360 ISAM FX-16 shelves in a 23 in. rack. An example of a configuration is shown in Figure 3-1.
Table 3-2 Rack mounting configurations for 7360 ISAM FX-16
FEMA code 3FE 66742 AA 3FE 66742 AB
Rack unit 23 in. rack vertical mount
SR 1 NFXS-D NFXS-D
Fiber and heat baffle kit Fiber and heat baffle kit
Left and right mounting brackets Left and right mounting brackets
Fan 1 AFAN-H(with fan filter)
AFAN-H(with fan filter)
SR 2 NFXS-D
Fiber and heat baffle kit
Left and right mounting brackets
Fan 2 AFAN-H(with fan filter)
-
3 Rack mounting configurations
3-4 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
Figure 3-1 Rack mounting configurations for 7360 ISAM FX-16 (3FE 66742 AB)
BITS INTERFACE TIME OF DAY1 Hz-PULSE
NT-A NT-BRINGTIPFRAME GND
CO ALARMSCRAFT PORT
BITS INTERFACE TIME OF DAY1 Hz-PULSE
NT-A NT-BRINGTIPFRAME GND
CO ALARMSCRAFT PORT
22732
34 RU
21.522.3
-
3 Rack mounting configurations
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 3-53FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
3.4 7360 ISAM FX-8 rack mounting configurations
This section describes the 7360 ISAM FX-8 rack mounting configurations.
The 7360 ISAM FX-8 can be installed:
horizontally in an EIA standard 19 in. rack horizontally in a 23 in. rack
Table 3-3 lists the supported horizontal rack mounting configurations for 7360 ISAM FX-8 shelves.
Table 3-3 Horizontal rack mounting configurations for 7360 ISAM FX-8
Note(1) Although only two rack units are portrayed in this table, up to five rack units are supported.
Figure 3-3 shows the 7360 ISAM FX-8 horizontal rack mounting configurations in am EIA standard 19 in. rack.
Note A 19 in. seismic rack with a 17.5 in. shelf aperture between the uprights is not supported.
Rack unit (1) 19 in. EIA rack horizontal mount 23 in. rack horizontal mount
SR 1 NFXS-E NFXS-E
Shelf mounting kit Shelf mounting kit
Fan 1 AFAN-E(with fan filter)
AFAN-E(with fan filter)
SR 2 NFXS-E
Shelf mounting kit
Fan 2 AFAN-E(with fan filter)
-
3 Rack mounting configurations
3-6 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
Figure 3-2 Horizontal rack mounting configurations for 7360 ISAM FX-8 in an EIA standard 19 in. rack
Figure 3-3 shows the 7360 ISAM FX-8 horizontal rack mounting configurations in a 23 in. rack.
Energy Hazzard
22736
TOD/IHZ
FAN
NTA
NTIO
NTB
0102
0304
0506
0708
7360
ISAM
FX-
8
Energy HazardCritical
Alarms
ACOBAT ARemote CraftBITSExternal Alarms
MajorMinor
BAT B
7360 ISAM FX-8B-40A
A-40ANTA GND NTB
18.31217.750
35 RU
8 RU
-
3 Rack mounting configurations
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 3-73FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
Figure 3-3 Horizontal rack mounting configurations for 7360 ISAM FX-8 in a 23 in. rack
Energy Hazzard
TOD/IHZ
FAN
NTA
NTIO
NTB
0102
0304
0506
0708
7360
ISAM
FX-
8
Energy HazardCritical
Alarms
ACOBAT ARemote CraftBITSExternal Alarms
MajorMinor
BAT B
7360 ISAM FX-8B-40A
A-40ANTA GND NTB
22734
22.31321.500
35 RU
8 RU
-
3 Rack mounting configurations
3-8 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
3.5 7360 ISAM FX-4 rack mounting configurations
This section describes the 7360 ISAM FX-4 rack mounting configurations.
The 7360 ISAM FX-4 shelf can be installed:
horizontally in an EIA standard 19 in. rack horizontally in a 23 in. rack
Table 3-4 lists the supported horizontal rack mounting configurations for 7360 ISAM FX-4 shelves.
Table 3-4 Horizontal rack mounting configurations for 7360 ISAM FX-4
Note(1) Although only two rack units are portrayed in this table, up to seven rack units are supported.
Figure 3-5 shows the 7360 ISAM FX-4 horizontal rack mounting configurations in an EIA standard 19 in. rack.
Note A 19 in. seismic rack with a 17.5 in. shelf aperture between the uprights is not supported.
Rack unit (1) 19 in. EIA rack horizontal mount 23 in. rack horizontal mount
SR 1 NFXS-F NFXS-F
Shelf mounting kit Shelf mounting kit
Fan 1 AFAN-X(with fan filter)
AFAN-X(with fan filter)
SR 2 NFXS-F NFXS-F
Shelf mounting kit Shelf mounting kit
Fan 2 AFAN-X(with fan filter)
AFAN-X(with fan filter)
-
3 Rack mounting configurations
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 3-93FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
Figure 3-4 Horizontal rack mounting configurations for 7360 ISAM FX-4 in an EIA standard 19 in. rack
Figure 3-5 shows the 7360 ISAM FX-4 horizontal rack mounting configurations in a 23 in. rack.
22740
18.31217.750
38 RU
5 RUFAN
NTA
NTI
ON
TB01
0203
04
7360
ISAM
FX-4
TOD/IHZ Critical AlarmsFUSEBAT ARemote CraftBITSExternal Alarms
NTA GND NTB
Major ACO1A B
23 Minor
BAT BN594
7360 ISAM FX-4
-
3 Rack mounting configurations
3-10 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
Figure 3-5 Horizontal rack mounting configurations for 7360 ISAM FX-4 in a 23 in. rack
22738
22.31321.500
38 RU
5 RUFAN
NTA
NTI
ON
TB01
0203
04
7360
ISAM
FX-4
TOD/IHZ Critical AlarmsFUSEBAT ARemote CraftBITSExternal Alarms
NTA GND NTB
Major ACO1A B
23 Minor
BAT BN594
7360 ISAM FX-4
-
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 4-13FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
4 Optical modules
4.1 Overview 4-2
4.2 Characteristics 4-2
-
4 Optical modules
4-2 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
4.1 Overview
This chapter describes the Alcatel-Lucent approved SFP and XFP optical modules for the 7360 ISAM FX.
4.2 Characteristics
Table 4-1 describes the Alcatel-Lucent approved optical modules for the 7360 ISAM FX. See Chapter 6, Table 6-12 for part numbers and the cards that these modules support.
Table 4-1 Characteristics of approved optical modules
Part number
Description Wavelength(nm)
Operating casetemperature range
Opticalbudget(dB)
Reach Fiber Bidi /uni
UDS(1)
Fast Ethernet SFPs
3FE 25777 AA FE-FX 1310 40C to 85C40F to 185F
12 0.550 km0.342 mi
MM Uni DAAA
3FE 25778 AA FE-LX10 1310 40C to 85C40F to 185F
16 15 km9.3 mi
SM Uni
3FE 29194 AA FE BX10-D Tx: 1550Rx: 1310
40C to 85C40F to 185F
14 10 km6.2 mi
SM Bidi FAAA
3FE 29194 BA FE BX10-D Tx: 1490Rx: 1310
40C to 85C40F to 185F
14 10 km6.2 mi
SM Bidi
3FE 29195 AA FE BX10-U Tx: 1310Rx: 1550
40C to 85C40F to 185F
14 10 km6.2 mi
SM Bidi
3FE 63343 AA 100Base-T 0C to 70C32F to 188F
0.100 km0.062 mi
Cat5 PAAA
Copper SFPs
3FE 28784 AA 1000Base-T 0C to 85C32F to 188F
0.10 km0.06 mi
Cat5 EAAA
3FE 64927 AA 1000Base-T 40C to 85C40F to 185F
0.10 km0.06 mi
Cat5
Gigabit Ethernet SFPs
3FE 25773 AA GE-SX 850 40C to 85C40F to 185F
7 0.55 km0.34 mi
MM Uni CAAA
3FE 25774 AA GE-LX 1310 40C to 85C40F to 185F
11 10 km6.2 mi
SM Uni
3FE 25775 AA GE-EX 1310 40C to 85C40F to 185F
18 40 km24.9 mi
SM Uni
3FE 25776 AA GE-ZX 1550 40C to 85C40F to 185F
24 80 km49.7 mi
SM Uni
(1 of 4)
-
4 Optical modules
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 4-33FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
3FE 25771 AA GE-YX CWDM (24 dB)
1471 40C to 85C40F to 185F
22 62 SM Uni AAAA
3FE 25771 AB 1491
3FE 25771 AC 1511
3FE 25771 AD 1531
3FE 25771 AE 1551
3FE 25771 AF 1571
3FE 25771 AG 1591
3FE 25771 AH 1611
3FE 25771 CA GE-VX CWDM (32 dB)
1471 5C to 85C32F to 185F
31 120 SM Uni
3FE 29549 CA 1491
3FE 29550 CA 1511
3FE 29551 CA 1531
3FE 29552 CA 1551
3FE 29553 CA 1571
3FE 29554 CA 1591
3FE 29555 CA 1611
3FE 25772 AA GE-BX10-U Tx: 1310Rx: 1490
40C to 85C40F to 185F
9 10 km6.2 mi
SM Bidi GAAA
3FE 25772 AB GE-BX10-D Tx: 1490Rx: 1310
40C to 85C40F to 185F
9 10 km6.2 mi
SM Bidi
3FE 28785 AA GE-BX40-U Tx: 1310Rx: 1550
40C to 85C40F to 185F
19 40 km24.9 mi
SM Bidi
3FE 25785 AB GE-BX40-D Tx: 1550Rx: 1310
40C to 85C40F to 185F
19 40 km24.9 mi
SM Bidi
3FE 28784 AA 1000Base-T 0C to 85C32F to 188F
0.100 km0.062 mi
Cat5 EAAA
SFP+s
Part number
Description Wavelength(nm)
Operating casetemperature range
Opticalbudget(dB)
Reach Fiber Bidi /uni
UDS(1)
(2 of 4)
-
4 Optical modules
4-4 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
3FE 62600 AA 10 GE-R 1310 40C to 85C40F to 185F
10 10 km6.2 mi
SM Uni MAAA
3FE 62600 CA 10 GE-R 1310 5C to 85C32F to 185F
10 10 km6.2 mi
SM Uni
3FE 62600 DA 10 GE-R 1310 0C to 70C32F to 188F
10 10 km6.2 mi
SM Uni
3FE 62600 EA 10 GE-R 1310 40C to 85C40F to 185F
10 10 km6.2 mi
SM Uni
3FE 65608 AA 10 GE-R 850 0C to 70C32F to 188F
11 0.3 km0.19 mi
MM Uni
3FE 63264 AA 10 GE-R 850 40C to 85C40F to 185F
11 0.3 km0.19 mi
MM Uni
3FE 65831 AA 10 GE-R 1550 40C to 85C40F to 185F
15 40 km24.9 mi
SM Uni
3FE 65832 AA 10 GE-R 1550 40C to 85C40F to 185F
24 80 km53.3 mi
SM Uni
E1 SFPs
3FE 67231 AA E1/T1 SFP 40C to 65C40F to 149F
E1/T1: short haul0.5 km0.31 miE1/T1: long haul2.1 km1.3 mi
Uni XAAA
Dual SFPs
3FE 65106 AA GE-BX10-D Tx: 1490Rx: 1310
40C to 85C40F to 185F
9 10 km6.2 mi
SM Bidi TAAA
3FE 65106 DA GE-BX10-D Tx: 1490Rx: 1310
0C to 70C32F to 188F
9 10 km6.2 mi
SM Bidi
3FE 65107 AA FE-BX10-D Tx: 1550Rx: 1310
40C to 85C40F to 185F
14 10 km6.2 mi
SM Bidi
3FE 65107 DA FE-BX10-D Tx: 1550Rx: 1310
0C to 70C32F to 188F
14 10 km6.2 mi
SM Bidi
3FE 66131 AA FE-BX10-DGE-BX10-D
Tx: 1490Rx: 1310
40C to 85C40F to 185F
8 (FE)9 (GE)
10 km6.2 mi
SM Bidi
Part number
Description Wavelength(nm)
Operating casetemperature range
Opticalbudget(dB)
Reach Fiber Bidi /uni
UDS(1)
(3 of 4)
-
4 Optical modules
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 4-53FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
Note(1) For more information about the characteristics of the SFP module, see UDS 3HH 01046 xxxx TQZZA, where xxxx is the
document variant indicated in this column.
3FE 66131 DA FE-BX10-DGE-BX10-D
Tx: 1490Rx: 1310
0C to 70C32F to 188F
91000Base-BX108100Base-BX10
10 km6.2 mi
SM Bidi
GPON SFP
3FE 53441 AA Class B+, normal
Tx: 1490Rx: 1310
5C to 70C23F to 188F
28 30 km18.6 mi
SM Bidi RAAA
3FE 53441 AC Class B+, normal
Tx: 1490Rx: 1310
40C to 85C40F to 185F
28 30 km18.6 mi
SM Bidi
3FE 53441 BA Class C+, normal
Tx: 1490Rx: 1310
5C to 70C23F to 188F
32 60 km37.3 mi
SM Bidi
3FE 53441 CC Class B+ with OTDR
Tx: 1490Rx: 1310
40C to 85C40F to 185F
28 30 km18.6 mi
SM Bidi
3FE 53441 DA Class C+, with OTDR
Tx: 1490Rx: 1310
5C to 70C23F to 188F
32 60 km37.3 mi
SM Bidi
XG-PON XFPs/SFPs
3FE 53971 AA XG-PON1 OLT XFP
Tx: 1577Rx: 1270
5C to +70C+23F to +185F
29 dB 40 km SM Bidi YAAA
3FE 53972 AA XG-PON1 ONU SFP+
Tx: 1577Rx: 1270
40C to +85C 40F to +185F
29 dB 40 km SM Bidi
Other
3FE 66247 AA TM1 SFP 40C to 70C40F to 158F
28 SM Uni WAAA
Part number
Description Wavelength(nm)
Operating casetemperature range
Opticalbudget(dB)
Reach Fiber Bidi /uni
UDS(1)
(4 of 4)
-
4 Optical modules
4-6 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
-
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 3FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
Planning and ordering
5 Planning the equipment
6 Ordering the equipment
-
May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
-
Alcatel-Lucent 7360 ISAM FX R04.04 May 2012 5-13FE 54967 AAAA TCZZA Edition 01ANSI Product Information Guide
5 Planning the equipment
5.1 Overview 5-2
5.2 Network considerations 5-2
5.3 Rack considerations 5-4
5.4 Shelf considerations 5-4
5.5 LT card considerations 5-5
5.6 NT card considerations 5-5
5.7 V-OLT and video coupler equipment considerations 5-5
5.8 Installation considerations 5-7
5.9 Power considerations 5-8
5.10 Maintenance considerations 5-8
5.11 Software licensing information 5-8
5.12 Documentation 5-8
-
5 Planning the equipment
5-2 May 2012 Alcatel-Lucent 7360 ISAM FX R04.04Edition 01 3FE 54967 AAAA TCZZA
ANSI Product Information Guide
5.1 Overview
This chapter provides planning considerations for ordering the 7360 ISAM FX equipment. Consider the following items when determining what you need:
required number and type of shelves rack requirements shelf power and mounting accessories shelf hardware kits and shelf add-on kits installation-related items, such as power and alarm equipment expansion configuration requirements software licensing documentation other requirements, such as MTA, ITSC, and BITS
5.2 Network considerations
This section describes the 7360 ISAM FX network equipment considerations including system planning.
The 7360 ISAM FX is implemented in an access network topology that extends optical access across the last mile of the communications network to the subscriber using fiber optic cable to provide services from the network to residential or business subscribers.
The 7360 ISAM FX access network consists of four distinct equipment types:
P-OLT, which includes the rack and shelves, and the corresponding NT and LT cards
V-OLT, which distributes RF overlay video signals across the GPON if the network provider chooses this method for providing video services
WDM, which is only required to support the V-OLT, and is used to mix and separate the RF video signals to and from the optical fiber going toward ONUs.
ONU, which is located at the subscriber premi