4-port antenna r1 y1 frequency range dual polarization x x ... · page 2 of 3 80010664 936.4850/b...
TRANSCRIPT
80010664 Page 1 of 3
936.4
850/b
S
ub
ject
to a
ltera
tio
n.
4-Port Antenna 790–960/1710–2690 65°/65° 15/17.5dBi 0°–16°/2°–10°T
Type No. 80010664Lowband R1, connector 1–2R1, connector 1–2
790–960Frequency range MHz 790 – 862 824 – 894 880 – 960
Polarization ° +45, –45 +45, –45 +45, –45
Average gainTilt
dBi°
14.5 ... 14.4 ... 14.20 ... 8 ... 16
14.6 ... 14.5 ... 14.30 ... 8 ... 16
14.8 ... 14.6 ... 14.40 ... 8 ... 16
Horizontal Pattern:Half-power beam width ° 69 68 67°
Front-to-back ratio, copolar (180°±30°) dB > 25 > 25 > 25
Cross polar ratioMaindirection 0°Sector ±60°
dB Typically: 25> 10
Typically: 25> 9
Typically: 25> 8
Horizontal Pattern:Half-power beam width ° 16.5 16.0 15.5
Electrical tilt ° 0–16, continuously adjustable
Sidelobe suppression for fi rst sidelobe above main beam
° TdB
0 ... 8 ... 1616 ... 15 ... 15
0 ... 8 ... 1616 ... 15 ... 15
0 ... 8 ... 1615 ... 15 ... 14
Impedance Ω 50
VSWR < 1.5
Isolation: Intrasystem dB > 30
Isolation: Intersystem dB > 30 (698–960 // 1710–2690 MHz)
Intermodulation IM3 dBc < –150 (2 x 43 dBm carrier)
Max. effective power per portMax. effective power for the antenna
W300 (at 50 °C ambient temperature)600 (at 50 °C ambient temperature)
4-Port AntennaFrequency RangeDual PolarizationHPBWAdjust. Electr. DTset by hand or by optional RCU (Remote Control Unit)
1710–2690
Y1Y1
790–960
R1R1
XX
65°65°
2°–10°0°–16°
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com
Page 2 of 3 80010664
936.4
850/b
S
ub
ject
to a
ltera
tio
n.
Highband Y1, connector 3–4Y1, connector 3–4
1710–2690Frequency range MHz 1710 – 1880 1850 – 1990 1920 – 2170 2300 – 2400 2490 – 2690
Polarization ° +45, –45 +45, –45 +45, –45 +45, –45 +45, –45
Average gainTilt
dBi°
17.2 ... 17.3 ... 16.82 ... 6 ... 10
17.4 ... 17.4 ... 16.92 ... 6 ... 10
17.6 ... 17.7 ... 17.02 ... 6 ... 10
17.0 ... 16.8 ... 16.02 ... 6 ... 10
17.2 ... 17.3 ... 16.72 ... 6 ... 10
Horizontal Pattern:Half-power beam width ° 63 64 66 73 65
Front-to-back ratio, copolar (180°±30°) dB > 25 > 28 > 29 > 26 > 25
Cross polar ratioMaindirection 0°Sector ±60°
dBTypically: 18
> 9> 20> 10
20> 10
23> 10
23> 8
Horizontal Pattern:Half-power beam width ° 6.2 5.8 5.6 5.4 4.8
Electrical tilt ° 2–10, continuously adjustable
Sidelobe suppression for fi rst sidelobe above main beam
°TdB
2 ... 6 ... 1014 ... 15 ... 16
2 ... 6 ... 1014 ... 15 ... 17
2 ... 6 ... 1015 ... 16 ... 17
2 ... 6 ... 1017 ... 18 ... 18
2 ... 6 ... 1015 ... 17 ... 18
Impedance Ω 50
VSWR < 1.5
Isolation: Intrasystem dB > 28 > 30
Isolation: Intersystem dB > 30 (790–960 // 1710–2690 MHz)
Intermodulation IM3 dBc < –150 (2 x 43 dBm carrier)
Max. effective power per portMax. effective power for the antenna
W 200 (at 50 °C ambient temperature)400 (at 50 °C ambient temperature)
4-Port Antenna
Mechanical specifi cations
Input 4 x 7-16 female (long neck)
Connector position Bottom
Adjustment mechanism 2x, Position bottomcontinuously adjustable
Wind load (at Rated Wind Speed: 150 km/h)
N | lbf Frontal: 260 | 58Maximal: 415 | 93
Max. wind velocity km/hmph
200124
Height / width / depth mminches
1403 / 300 / 15255.2 / 11.8 / 6.0
Category of mounting hardware
M (Medium)
Weight kglb
18 / 20 (clamps incl.)39.7 / 44.1 (clamps incl.)
Packing size mminches
1726 x 322 x 19068.0 x 12.7 x 7.5
Scope of supply Panel and 2 units of clamps for 42–115 mm |
1.7–4.5 inches diameter
R1Y1
Correlation Table
Frequency range Array Connector
790– 960 MHz R1 1–2
1710–2690 MHz Y1 3–4
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com
173 | 6
.8 *
46 | 1
.8
49 | 1
.9
108
| 4
.3
101 | 4.0
221 | 8.7
244 | 9.6
152 | 6
.0 *
300 | 11.8 *
Tilt 1710-2690Tilt 7
90-960
Bottom view* Dimensions refer to radomeAll dimensions in mm | inches
Any previous data sheet issues have now become invalid.
80010664 Page 3 of 3
936.4
850/b
S
ub
ject
to a
ltera
tio
n.
AccessoriesGeneral Information
For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.Wall mounting: No additional mounting kit needed.
Material: Refl ector screen: Aluminum.Fiberglass housing: It covers totally the internal antenna components. The special design reduces the sealing areas to a minimum and guarantees the best weather protection. Fiberglass material guarantees optimum performance with regards to stability, stiffness, UV resistance and painting. The color of the radome is light grey.All nuts and bolts: Stainless steel or hot-dip galvanized steel.
Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded.
Adjustment mechanismwith integrated scale
All dimensionsin mm | inches
1403 | 5
5.2
1433 | 5
6.4
1473 | 5
8.0
2)1)
1) 9 | 0.42) 64 | 2.5
Layout of interface:
Accessories (order separately if required)
Type No. Description Remarksmm | inches
Weight approx.kg | lb
Units per antenna
85010002 1 clamp Mast diameter: 110 – 220 | 4.3 – 8.7 2.7 | 6.0 2
85010003 1 clamp Mast diameter: 210 – 380 | 8.3 – 15.0 4.8 | 10.6 2
737978 1 downtilt kit Downtilt angle: 0° – 15° 2.3 | 5.1 1
Accessories (included in the scope of supply)
738546 1 clamp Mast diameter: 42 – 115 | 1.7 – 4.5 1.1 | 2.4 2
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com
738546 Page 1 of 1
Mounting HardwareClamp Included in the Scope of Supply
936.
3920
/c
Sub
ject
to a
ltera
tion.
Suitable for mast diameter (mm)[inches]
42 – 115[1.65 – 4.53]
Antenna – mast distance (mm)[inches]
20 – 25[0.79 – 0.98]
Material of clamp and screws Hot-dip galvanized steel / stainless steel
Weight (kg)[lb]
1.1[2.43]
Please note: Kathrein does not recommend to use counter nuts.The additional nuts supplied are only meant as spares.
All dimensions in mm and [inches]
152 [5.98]
100 [3.94]40 [1.57]
72 [2.83]
35 [1.38]
64 [2.52]
125 [4.92]
40 [1
.57]
20–
25
[0.7
9–
0.98
]
42–115
[1.65–4.53]
M10 MA = 25 Nm
M8 MA = 20 Nm
20–25
[0.79–0.98]
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com
Page 1 of 2
936.4
037/a
S
ub
ject
to a
ltera
tio
n.
General Instructionsfor Adjustment Mechanism
Description of the adjustment mechanism (protective cap removed):
Manual adjustment procedure:
Optional: RCU (Remote Control Unit) for remote-controlled downtilt adjustment:
For a description of RCU installation please refer to the respective data sheet.
Remove the protective cap and the
twist protection completely.
➀ Twist protection.
➁ Downtilt spindle with integrated
scale.
➀ Thread for fi xing the pro tective
cap or the RCU (Remote Control
Unit).
➁ Gearwheel for RCU power drive.
To set the downtilt angle exactly,
you must look horizontally at the
scale. The lower edge of the gear-
wheel must be used for alignment.
Set downtilt angle by rotating the
gearwheel.
Screw on the twist protection and
the protective cap again.
0° – max.°
0° – max.°
1
2
2
1
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com
Page 2 of 2
936.4
037/a
S
ub
ject
to a
ltera
tio
n.
Installation of the feederline connector and RCU (optional):In order to protect the adjustment mechanism, the protective caps have to be attached during feederline installation!
Carefully place the connector and
fi x the nut using a torque-wrench
(according to the manufacturers
guidelines).
After feederline installation, the
optional remote control units
(RCUs) can be mounted.
These tools are suitable for 7-16 connectors with a wrench size of
27 or 32 mm | 1.1 or 1.3 inches, and the RCU attachment nut with a
wrench size of 41 mm | 1.6 inches.
Tighten nuts within a torque range of 25 – 33 Nm depending on
connector manufacturers’ specifi cations, respectively the RCU nut
with a torque range of 15 – 18 Nm.
Kathrein installation set: Type No. 85010077Set has to be ordered separately!Set consists of three spanners of divers width27, 32 and 41 mm | 1.1, 1.3 and 1.6 inches
32 | 1.3
41 | 1
.627 | 1
.1
1/2˝ square actuationaccording toDIN 3120 Form C
All dimensions in mm | inches
Colour coding:Correlation of each RF input to:– the corresponding adjustment mechanism– the frequency range– the polarization
Ventilation hole
Spindle with tilting scale
7-16 female (long neck)
Adjustment mechanism(protective cap removed)
General Instructions for Feederline and RCU Installation for Antennas
Please note: In order not to damage the interfaces, please make sure that only the right tools are used.
Tighten the feederline connector interfaces solely by using a common torque-wrench with a suitable wrench
width.
Description of bottom end cap (exemplary picture):
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com