6951943-83b921-hino_700_series_05_on

HINO

700 Series

2005 on

Euro 4

ALL

24v VOLTAGE

TRANSMISSION

ENGINE TYPE

YEAR OF MANUFACTURE

MODEL

VEHICLE MANUFACTURER

Digital Application Sheet

STONERIDGE DIGITAL KIT FOR THIS VEHICLE: 7800-057

PARTS LIST

SE5000 TACHOGRAPH

HARNESS

SENDER

SENDER CABLE

SHROUD SEALING KIT

DRIVER QUICKGUIDE

1

0

1

1

QUANTITY STONERIDGE PART NO.

INSTALLATION KIT

APPLICATION SHEET

1

1

1

6800321

ADDITIONAL VEHICLE MANUFACTURERS PARTS REQUIRED VEHICLE MANUFACTURERS PART NO.

FITTING INFORMATION

Workshop Technical Support

Tel +44 (0)1382 866 400 (choose opt.2. opt.1 )

Fax +44(0) 1382 866 401

Email [email protected]

Sales Office

Tel +44 (0)1382 866 400 (choose opt.1)

Fax +44(0) 1382 866 401


Whilst we have endeavoured to ensure the accuracy of the information supplied, Stoneridge Electronics cannot be held responsible for any errors or omissions. It is the installer's responsibility to ensure compliance with specific vehicle manufacturers repair procedures, especially with regard to the procedure for disconnection/reconnection of the battery. Failure to comply with the vehicle manufacturers

instructions may result in personal injury and/or component damage/data loss.

ALWAYS CHECK BEFORE FITTING A SENDER

A KRM series SE5000 programmed using the SE5000 Configuration System can also be used in this vehicle.

SE5000 Programming Sheet

PROGRAMMING PARAMETERS FOR FITTING THIS VEHICLE WITH AN SE5000 KRM SERIES TACHOGRAPH.





Fax +44(0) 1382 866 401


Sales Office

Tel +44 (0)1382 866 400 (choose opt.1)

Fax +44(0) 1382 866 401


Note. Read the parameters of the tachograph to be replaced, and note all connections to the tachograph,

paying particular attention to Vpulse, dual axle configuration, D8 serial data, Revs input etc.

The below vehicle settings are the default vehicle settings which should be applied. However, individual

vehicle specifications may vary.

Default setting for D6 outputs that can be switched between ISO & Open collector (o/c) is ISO.

The vehicle must be calibrated in an approved manner after fitting.

The road speed limiter must be calibrated after a replacement tachograph is fitted.

The illumination of the KRM series tachograph can be changed between White & Green, please select the

colour best suited to the vehicle illumination.

If you are in doubt regarding the replacement of any tachograph with a KRM series product please call:-

Workshop Support on 0870 887 9200 option2, option1. or email [email protected]

TACHOGRAPH CANBUS CAN CAN TERMINATION

ILLUMINATION REVS INPUT SPEED LIMITER SETTING

D6

5011KRM N/A N/A N/A A2 C3 90km/H O/C

READ ALL DATA LOG

PARAMETER VALUE / SETTING PARAMETER VALUE / SETTING

W-FACTOR

K-FACTOR L-FACTOR

TYRE SIZE

VIN

VEH. REG. NATION

VRN

PREF. LANGUAGE

CURRENT TIME

CURRENT DATE

TIME OFFSET

NEXT CALIB.DATE

INSTALL DATE

ACTIVATION TIME

SERVICE DELAY

ODOMETER

O/P SHAFT FACTOR

SPEEDO OP FACTOR

RESET HEARTBEAT

LOW SPEED LIMIT

BACKLIGHT SELECT

ILLUMINATION LEVEL

ILLUMINATION OFF

Def. KEY ON/OFF

RPM FACTOR

D4 PIN FUNCTION

D5 PIN FUNCTION

D6 PIN FUNCTION

D7 PIN FUNCTION

SERIAL DATA OUT (D8)

C1 PIN FUNCTION

FILTER PIN B3

CAN TRIP RESET

CAN WAKE UP

RD CAN CONFIG

ADD. EVENT REC.

ENG. SPEED REC.

VRESD

VEH. SPEED REC.

VRVSD

PRE-OVERSPEED

PRE-NEXT CALIBRATION

WARRANTY TIME

LOW POWER BAND

ECONOMY POWER BAND

POOR ECONOMY

READ ONLY. –DATE FORMAT / UNACTIVATED




Fax +44(0) 870 704 0002


Sales Office

Tel +44 (0)871 700 7070 (choose opt.1)

Fax +44(0) 870 704 0002




1. Fit the encrypted sender to the gearbox. 2. Connect the 6m cable to the sender and ensure the sender is sealed to the gearbox.

3. Feed the cable up through the chassis of the vehicle following the other cables on route to the cab.

4. Ensure that it is appropriately cable tied to avoid loose loops that may catch..




Fax +44(0) 870 704 0002


Sales Office

Tel +44 (0)871 700 7070 (choose opt.1)

Fax +44(0) 870 704 0002




5. Open the bonnet of the cab and remove the screws from the metal cover on the right hand side, then feed the cable through.

6. Remove the 2 screws from the plastic cover and feed the cable into the cab through one of the three rubber wire protectors.

7. Feed the cable behind the dashboard to exit behind the cabs centre console. Remove one of the two tidy trays and fit the radio cage for the Digital Tachograph.

8. Behind the centre console you will find a harness which you can take the power, light-ing, ignition and ground signals from. See Appendix for signal references to the wire colours.




Fax +44(0) 870 704 0002


Sales Office

Tel +44 (0)871 700 7070 (choose opt.1)

Fax +44(0) 870 704 0002




13. The D6 Speedo output factor should be set to 7450 to ensure the odometer on the cluster matches the odometer on the tachograph.

10. The speed signal wire can be found either behind the centre console (red wire with silver spots) or at the Rate Converter under the fuse board behind the passenger dash (blue wire with red stripe).

11. Click the passenger dash back carefully after ensuring all connections are sealed properly. 12. Fully press the tachograph into the radio cage ensuring a solid and tight fit, then calibrate ac-cordingly.

9. Connect pin D6 from the tachograph to the speed signal wire on the vehicle.




Fax +44(0) 870 704 0002


Sales Office

Tel +44 (0)871 700 7070 (choose opt.1)

Fax +44(0) 870 704 0002




Wire Harness Tachograph Connector Tachograph Connector Colour Blue with Yellow Stripe Main Power (A1) Red Red with Black Stripe Lighting (A2) Red with Silver Stripe White with Blue Stripe Ignition (A3) Black Brown with Silver Spot Ground (A5 & A6) Brown & Brown with Black Stripe

Appendix: Tachograph Harness (Supplied)

6951943-83b921-hino_700_series_05_on

Documents