8mm one door offset quadrant · product name:8mm one door offset quadrant product code: customer...
TRANSCRIPT
8mm ONE DOOR OFFSET QUADRANT Refer To Sheet 9 For Relevant Product Codes
VictoriaPlum.com0344 804 48 48
RH LH
RIGHT HAND ILLUSTRATED
Handle is supplied in separate carton (H).
1
BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION
1) General Information
2) Additional Notes
Please inspect this product upon delivery, any missing parts or manufacturing
defects must be reported immediately to the supplier. Damage or defects reported
later will not be accepted. TAKE CARE WHEN HANDLING GLASS PARTS - AVOID
HEAVY CONTACT BETWEEN THE GLASS EDGES AND ANY HARD SURFACE.
Glass breakage claims will not be accepted after the product has been unpacked.
Please note: Aluminium is a soft metal, and undergoes a series of extrusion,
fabrication, polishing and anodising processes in order to create your finished
shower enclosure. Some light surface marks are normal, and is a result of the
manufacturing processes. Quality control has ensured that this item is of a good
standard, and is fit for purpose.
Please read these instructions carefully before starting installation.Special care should be taken when drilling walls to avoid hidden pipes or electrical cables.
Note: this product is heavy and may require two people to install.
This product is heavy and may require two people to install.
TOOLS REQUIRED
Ø3mm Drill bit
Ø6mm Drill bit
Pencil
Spirit level
Tape measure
DESCRIPTION DESCRIPTIONPART IMAGE PART IMAGE
Drill
Flat-headScrewdriver
Cross headScrewdriver
Mallet
Silicone Sealant
PZ1
ASSEMBLY INSTRUCTIONS - DRAWING
2
(8) 1x Handle (8mm Supplied Separately)
(1) 2x Cover Caps (Guide Rail)(2) 4x Glass To Rail Brackets
(4) 8x Screws 4x30
(3) 8x Wall Plugs
(5) 2x Wall Profiles (6) 2x Wedge Gasket Seals(7) 1x Fixed Panel A
(9) 1x Bottom Sliding Block(10) 1xDrip Strip End Cap(11) 1x Drip Strip
(12) 1xBottom Guide Block A
(13) 1x Bottom Guide Block B(14) 1x Fixed Panel B
(18) 1xTop Seal(19) 1x Moving Panel (20) 2x Rollers(21) 1x Top Profile
(23) 2x Bump Stop Caps
(15) 4x Screws(16) 2x Wall Profile Cover Caps
(24) 4x Screw Caps
(22) 1x Fixed Panel Seal
(17) 1x Fixed Panel Seal
PACK I.D PACK I.DEE
EEB
EAHEEB
E
EA
EEC
CAEBCE
E
NB: ALL MEASUREMENTS + COMPONENT SIZES QUOTED ARE IN MM.
THESE DIMENSIONS ASSUME THE WALLS ARE PLUMB AND THE SHOWER TRAY IS LEVEL, AND THAT THE WALLS ARE TILED DOWN TO THE TOP OF THE TRAY USING A 10mm TILE/WET WALL PANEL.
ASSEMBLY INSTRUCTIONSIf you require help, we advise you to contact a competent plumber.
Installation Steps
3
FITTED ONE DOOR QUADRANT DRAWING
20
900/1000/1200
76
0/8
00
/90
0
20
LH
20
900/1000/1200
76
0/8
00
/90
0
20
RH
4
STEP CHECK BOX CONTENTS ARE CORRECT AND THEN MEASURE KEY COMPONENTS.1
STEP 2 DRAWING TO SHOW CORRECT SHOWER TRAY INSTALLATION
WALL
TILE OR WETWALL PANEL
SHOWER TRAY
YES
WALL
TILE OR WETWALL PANEL
SHOWER TRAY
NO
STEP 3 TRAY TO BE LEVEL
MAKE SURE THE TRAY IS LEVEL, USING A SPIRIT LEVEL, BEFORE INSTALLING THISSHOWER PANEL / DOOR, AND THAT SILICONE IS APPLIED ON ALL SIDES WHERE THETRAY MEETS THE TILES / WET WALL PANELS.
Top horizontal profiles
Measurement Matrix (before assembly) Dimension in mm
Units supplied loose for self assembly
Moving panel glass
Wall posts
Flat fixed panel glass
Curved fixed panel glass
1950x324x8 1950x324x8
1950x457x8 1950x457x8
1243 1243
1938x580x8 1938x580x8
1950x37 1950x37
DQD9762L DQD9762R
1950x424x8 1950x424x8
1950x497x8 1950x497x8
1383 1383
1938x580x8 1938x580x8
1950x37 1950x37
DQD8102L DQD8102R
1950x624x8 1950x624x8
1950x497x8 1950x497x8
1583 1583
1938x580x8 1938x580x8
1950x37 1950x37
DQD8122L DQD8122R
1950x624x8 1950x624x8
1950x547x8 1950x547x8
1673 1673
1938x630x8 1938x630x8
1950x37 1950x37
DQD9122L DQD9122R
STEP 5 FITTING THE FIXED PANELS
STEP 4 DRILLING WALL PROFILES TO THE WALL
5
10m
m1
x82 x8
Ø6mm
3
x85x84
84mm1
2
H2O
MAX:20mm
3
1
2
H2O
MAX:20mm
3
STEP 6 FITTING THE TOP PROFILE AND THE BOTTOM DRIP STRIP
6
STEP 7 FITTING THE ROLLERS
2
8mm glass3
4
1 x4
8mm glass
7
5
6
1 x2
2
8mm glass
STEP 8 ASSEMBLING THE GLASS TO RAIL BRACKETS, AND BOTTOM GUIDE BLOCKS
STEP 9 ADJUSTING THE MOVING PANEL AND FITTING END CAPS
x2Adjust
inside
5 6
7
8
9
inside
1
2
3
4
7
8
STEP 10 PUSH THE SEALS ON TO THE FIXED PANEL AND FIT THE HANDLE
STEP 11 SILICONE THE OUTSIDE EDGES
x2
8mm glass
INSIDE
Fin length 30mm
Fin length 25mm
Allow 24 hours for silicone to dry before use. Silicone on the
outside edge only, NOT THE INSIDE
CARE AND MAINTENANCE
COMMITMENT TO QUALITY
1) AFTER CARE INSTRUCTIONS
2) MAINTENANCE
Regularly clean your shower product with warm soapy water
Clean the plastic parts with a cloth and mild detergent. Never
use any abrasive creams, dissolvents, acetone or detergents
and disinfectants that contain chlorine. The supplier acceptsno liability for any type of use of care other than those contained
in these instructions. The supplier reserves the right to introduce
technical changes without notice.
It is our intention that the quality and functions of this productare of the highest standard. If you require help we advise you
firstly contact a competent plumber. However we understand that
this may not always be the case, so should you experience
any problems please contact our customer services quoting
the following:
to prevent lime scale build up. Do not use abrasive cleaning
fluids or materials, or strong chemical cleaners as this will
damage the product surface.
9
Product name: 8mm One Door Offset Quadrant
Product code:
Customer help line number: 0344 804 48 48
DQD9762L / DQD9762R / DQD8102L / DQD8102R DQD8122L / DQD8122R / DQD9122L / DQD9122R
10
INSTALLERS NOTES
V05/09/2019
The packaging you have received with your product is 100% recyclable.It must be disposed of in a safe and environmentally friendly way.
We suggest you take it to the local landfill site and discard in the designated bins.
Victoria Plum Limited, Bridgehead Business Hessle, HU13 0DG
Park
17
EN 14428:2015
DOP No.:J170320003-1
Shower enclosures with aluminiumprofiles and safety glass
Essentialcharacteristics
Performance Harmonisedtechnical
specificationCleanability
Impactresistance/shatter
properties
Pass
Pass
PassDurability
Clause 4.2 of EN 14428:2015
Clause 4.3 of EN 14428:2015
Clause 4.4 of EN 14428:2015