9/27/2004ee 42 fall 2004 lecture 121 lecture #12 circuit models for diodes, power supplies reading:...
TRANSCRIPT
9/27/2004 EE 42 fall 2004 lecture 12 1
Lecture #12 Circuit models for Diodes, Power supplies
Reading: Malvino chapter 3, 4.1-4.4
Next: 4.10, 5.1, 5.8
Then transistors (chapter 6 and 14)
9/27/2004 EE 42 fall 2004 lecture 12 2
Circuit models
• Now that we have studied the physics underlying how a diode works, we are going to hide all of it in a circuit model
Why?
• If we create a circuit model, then we can draw and analyze electronic circuits without getting lost in the details.
9/27/2004 EE 42 fall 2004 lecture 12 3
IV curve for an ideal diode
• The IV curve for a ideal diode is to have zero current in the reverse direction, and no resistance when forward biased
Voltage →
Current
9/27/2004 EE 42 fall 2004 lecture 12 5
Idealized devices
• We have encountered the idea of ideal devices before:
• A voltage source is like a battery, but produces a perfect voltage regardless of current:
And the ideal current
source, a current
regardless of voltage~
9/27/2004 EE 42 fall 2004 lecture 12 6
The ideal diode
• We now add another ideal device, the ideal diode.
A real diode drawn as the same symbolsometimes in a circle tomake it clear that it is nota ideal diode
9/27/2004 EE 42 fall 2004 lecture 12 7
The ideal diode as a switch
• The ideal diode behaves as a switch:
• If current is being pushed through in the forward direction the switch is closed.
• If a reverse bias voltage is applied, the circuit is closed.
Reverse Bias:
Forward Bias:
9/27/2004 EE 42 fall 2004 lecture 12 9
Ideal diode vs real diode IV curveWe could improve our model for real diode by not closing the switch until the voltage gets about 0.7 volts into the forward bias. We can do this in a circuit by making a circuit model
9/27/2004 EE 42 fall 2004 lecture 12 10
The ideal diodeTo make a somewhat better model of a real diode:
We use an ideal diode in series
with an ideal voltage source
~+
0.7 volts
-
9/27/2004 EE 42 fall 2004 lecture 12 11
Ideal diode vs real diode IV curveWe could improve our model further by sloping the IV curve for the region where forward current is flowing
9/27/2004 EE 42 fall 2004 lecture 12 12
Improved diode modelTo make an even better model of a real diode:
We use an ideal diode in serieswith an ideal voltage source anda resistor. The resistance needed forthe model is given by the inverse’of the slope of the IV curve
~+
0.7 volts
-
R
9/27/2004 EE 42 fall 2004 lecture 12 13
Key point: the model can change
• Which model you use for a device can change depending on – What the mode of operation of the device is– how accurately you need to model the device
For example: A hand analysis of a power supply would probably use an ideal diode, and then break the problem into two time periods– When the diode is forward biased– When the diode is reverse biased
9/27/2004 EE 42 fall 2004 lecture 12 14
Higher accuracy models
• If a diode was to be used at high frequencies (hundreds of megahertz or higher) then the model would have to account for the movement of charge in and out of the depletion zone, a capacitive effect.
It is important to use a model which is accurate enough to account for the necessary effects, without using so complicated a model that it is difficult to understand what is going on!
9/27/2004 EE 42 fall 2004 lecture 12 15
Applications
• Applications of diodes include• Power supply rectifiers• Demodulators• Clippers • Limiters • Peak detectors• Voltage references• Voltage multipliers
9/27/2004 EE 42 fall 2004 lecture 12 16
Half-wave rectifier
• A single diode can be used to take an alternating current, and allow only the positive voltage swing to be applied to the load
~ R
9/27/2004 EE 42 fall 2004 lecture 12 17
An AC input is sinusoidal
-1.5
-1
-0.5
0
0.5
1
1.5
0 5 10 15 20
9/27/2004 EE 42 fall 2004 lecture 12 18
The diode blocks the negative voltages
-0.2
0
0.2
0.4
0.6
0.8
1
1.2
0 5 10 15 20
9/27/2004 EE 42 fall 2004 lecture 12 19
Full-wave rectifier
• If we add an additional diode, it does not pass current at the same time as the first diode, but the load is now disconnected during the negative half cycle.
• What if we could flip the connection and use the negative half wave?
~ R
9/27/2004 EE 42 fall 2004 lecture 12 20
Full-wave rectifier
• The result is called a full wave rectifier
~ R
9/27/2004 EE 42 fall 2004 lecture 12 21
Full-wave rectified voltage
0
0.2
0.4
0.6
0.8
1
1.2
0 5 10 15 20
9/27/2004 EE 42 fall 2004 lecture 12 22
Transformers
• In order to use a full wave rectifier, the source and the load must be able to float with respect to each other
• One way to isolate AC power is to use a transformer. A transformer is a couple of coils of wire which transfer power by a changing magnetic field.
• By having different numbers of windings, or turns of wire, a transformer can step up or step down an AC voltage.
9/27/2004 EE 42 fall 2004 lecture 12 24
• The voltage across the secondary of the transformer (the output windings) is:
• But this only works for changes in the voltage—and therefore for AC only
11
22 V
N
NV
9/27/2004 EE 42 fall 2004 lecture 12 25
Filtering
• A transformer and a full wave rectifier will produce a voltage which is always positive, but varies with time
• In order to power electronic devices, we need to smooth out the variations with time.
• Another way to look at this is that we need to store energy temporarily while the input voltage changes sign.
9/27/2004 EE 42 fall 2004 lecture 12 26
Power supply filter capacitor
• If we add a capacitor in parallel with the load, it will charge up when power is available from the voltage source, and then it will slowly discharge through the load when the diodes are off.
~ R
9/27/2004 EE 42 fall 2004 lecture 12 27
Full wave rectified, with filtering
0
0.2
0.4
0.6
0.8
1
1.2
0 5 10 15 20