OMF / Oral Maxillo Facial

ARCS - Alveolarkamm Reconstruction SystemThe ARCS System meets the requirements of modern implantology. Atrophy of the alveolar crest causes continuous problems during restoration with dental implants in patients where there is not enough bone to locate the implants securely. The lack of bone can be overcome by using autologous bone grafts for example. One easy method to fix the bone graft is by using these micro screws, either alone or in combination with titanium micromesh.

• Three dimensional alveolar crest reconstruction

• System for fixation of: Bone blocks, Titanium Mesh, Sinus Implant Stabilizer, Micro Plates and Distractors.

• Highly biocompatible implant material

• Rapid and less resorbing bone regeneration

• Possibility of using autologeous bone only

• Very low infection risk

ARCSPre-Implantology

MONDEAL

Page 2

ARCS

Table of Contents

• Screws Page 3 - 4

• Microplates, Titanium MICRO-MESH Page 5

• Titanium Membranes Page 6

• Drills Page 7 - 8

• Instruments Page 9 - 10

• SIS - Sinus Implant Stabilizer Page 11

• SWING-LIFT Instruments Page 12

• ARCS PIN Page 13 - 14

• Container Page 15

The ARCS System ist compatible to the MONDEAL MICRO 1200 Microplate Osteosynthesis-System.

MONDEAL

Page 3

LOCK-DRIVE Screw

Art. No. Diameter x Length

31-71203 1.2 x 3 mm

31-71204 1.2 x 4 mm

31-71205 1.2 x 5 mm

31-71206 1.2 x 6 mm

31-71207 1.2 x 7 mm

31-71208 1.2 x 8 mm

31-71211 1.2 x 11 mm

31-71213 1.2 x 13 mm

31-71215 1.2 x 15 mm

Self-tapping Screws „Standard“ (Packaging: 5/ea.)

CROSS-FIT Screw

Art. No. Diameter x Length

31-81203 1.2 x 3 mm

31-81204 1.2 x 4 mm

31-81205 1.2 x 5 mm

31-81206 1.2 x 6 mm

31-81207 1.2 x 7 mm

31-81208 1.2 x 8 mm

31-81211 1.2 x 11 mm

31-81213 1.2 x 13 mm

31-81215 1.2 x 15 mm

LOCK-DRIVE Emergency Screw

Art. No. Diameter x Length

31-71504 1.5 x 4 mm

31-71506 1.5 x 6 mm

31-71511 1.5 x 11 mm

31-71513 1.5 x 13 mm

31-71515 1.5 x 15 mm

CROSS-FIT Emergency Screw

Art. No. Diameter x Length

31-81504 1.5 x 4 mm

31-81506 1.5 x 6 mm

31-81511 1.5 x 11 mm

31-81513 1.5 x 13 mm

31-81515 1.5 x 15 mm

MONDEAL

Page 4

Self-drilling Screws „Advanced“ (Packaging: 1/ea.)

• Self-drilling Screws with suitable thread component for bone anchorage

• Flat shaft for the transplant

• Approved titanium implant quality

CROSS-FIT Screw, self-drilling

Art. No. Diameter x Length

31-41208 1.35 x 8 mm

31-41210 1.35 x 10 mm

31-41212 1.35 x 12 mm

31-41214 1.35 x 14 mm

MCD Screw, self-drilling

Art. No. Diameter x Length

31-51208 1.35 x 8 mm

31-51210 1.35 x 10 mm

31-51212 1.35 x 12 mm

31-51214 1.35 x 14 mm

MONDEAL

Page 5

Microplates (Packaging: 1/ea.) Thickness: 0.6 mm

12-06108 8-hole Plate straight 12-06162 6-hole X-Plate

More microplates please find in our brochure MICRO 1200.

Titanium MICRO-MESH (Packaging: 1/ea.)

MICRO-MESH, Thickness: 0.1 mm

Art. No. Length x Width x Thickness

12-07001 50 x 30 x 0.1 mm

12-07002 100 x 60 x 0.1 mm

12-07003 100 x 30 x 0.1 mm

12-07004 50 x 60 x 0.1 mm

12-07005 120 x 120 x 0.1 mm

MICRO-MESH, Thickness: 0.2 mm

Art. No. Length x Width x Thickness

12-07011 50 x 30 x 0.2 mm

12-07012 100 x 60 x 0.2 mm

12-07013 100 x 30 x 0.2 mm

12-07014 50 x 60 x 0.2 mm

12-07015 120 x 120 x 0.2 mm

Indications: Stable covering of medium and large bone defects after filling with autologeous bone grafts or with bone substitute materials. Duration of implantation of the Titanium Mesh: approx. 3-4 months.

MONDEAL

Page 6

Titanium Membranes (Packaging: 1/ea.)

Art. No. Length x Width x Thickness

31-00220 20 x 25 x 0.02 mm

31-00230 30 x 25 x 0.02 mm

31-00240 40 x 25 x 0.02 mm

31-00250 50 x 25 x 0.02 mm

Art. No. Length x Width x Thickness

31-00233 30 x 30 x 0.03 mm

Indikations: Covering of medium and small bone defects as barrier between the mucosa and the bone for the unilateral bone regeneration (tenting procedure) also when using bone substitute materials. Duration of implantation of the Titanium Membrane: approx. 2-4 months.

TI-PORE Membrane: Ti-Pore membranes distinguish to normal membranes by the micro-perforation in the centre of the membrane. The special features secure the volume of the augmentation and offer an optimized stability of the augmented bone for perfect aesthetic results.

Both Titamium membranes can be cut to individual form and size!

ARCS Titanium Membrane, micro-perforated

MONDEAL

Page 7

Art. No. Diameter x Length Working Length (WL) End

12-12620 1.0 x 20 mm 5 mm Dental

12-12622 1.0 x 23 mm 8 mm Dental

12-12623 1.0 x 25 mm 10 mm Dental

12-12625 1.0 x 30 mm 15 mm Dental

For the drilling of the gliding hole

in the bone graft

Art. No. Diameter x Length Working Length (WL) End

11-12622 1.4 x 25 mm 10 mm Dental

10-67515 1.5 x 22 mm 9 mm Dental

10-67516 1.5 x 33 mm 20 mm Dental

Art. No. Diameter x Length Working Length (WL) End

12-12614 1.0 x 47 mm 5 mm Dental

12-12618 1.0 x 50 mm 8 mm Dental

Drill Gliding Hole Art. No. Diameter x Length Working Length (WL) End

11-13620 1.4 x 49 mm 10 mm Dental

Drills Max. 1.000 rpm

For angled handpiece

For straight handpiece

for Screws „Standard“

MONDEAL

Page 8

Optional Art. No. Diameter x Length Working Length (WL) End

12-12623 1.0 x 25 mm 10 mm Dental

12-12625 1.0 x 30 mm 15 mm Dental

Art. No. Diameter x Length Working Length (WL) End

11-12622 1.4 x 25 mm 10 mm Dental

Drills Max. 1.000 rpm

for Screws „Advanced“

MONDEAL

Page 9

Instruments

12-12000 Screwdriver handle, 9 cm

12-12001 LOCK-DRIVE blade

12-12054 CROSS-FIT holding device, not self-retaining

12-12019 CROSS-FIT screwdriver with holding device

12-12066 Screwdriver handle, short, 6 cm

12-12008 CROSS-FIT blade

12-12010 LOCK-DRIVE, screwdriver fixed, 13 cm, self-retaining

12-12018 CROSS-FIT, screwdriver fixed, 13 cm, self-retaining

for Screws „Standard“

MONDEAL

Page 10

Instruments

12-12002 LOCK-DRIVE blade, short, 2 cm, DENTAL, self-retaining

12-12009 CROSS-FIT Klinge, short, 2 cm, DENTAL, self-retaining

33-18235 Thumb Screw Mandrel for Dental shaft instruments

for Screws „Standard“

for Screws „Advanced“

11-12000 Screwdriver handle, 10 cm

11-12025 CROSS-FIT blade

11-12026 MCD blade

MONDEAL

Page 11

SIS - Sinus Implant Stabilizer (Packaging: 1/ea.)

12-06350 SIS Sinus Implant Stabilizer, standard

12-06351 SIS Sinus Implant Stabilizer, standard, curved

12-06352 SIS Sinus Implant Stabilizer, large

12-06353 SIS Sinus Implant Stabilizer, large, curved

12-12070 Drill guide, 1/ea. (2 ea. recommended)

acc. to Prof. Dr. M. Lang, Nürnberg

• The implant and the healing screw must have a diameter larger than 3.3 mm (respectively 3.6 mm). Depending on the implant system and implant diameter the SIS-Version „Standard“ or SIS-Version „large“ should be used.

• Handling: The SIS is fixed between the implant and the healing screw. This combination can additionally be secured with ARCS Microscrews through the small SIS holes inside the bone.

• To be used with following endosseus implants (without guarantee): Branemark - Nobel Biocare, Osseotite 3i - Implant Innovations®, Ankylos® - Friadent Dentsply, Bonefit-Straumann, Replace - Nobel Biocare, Camlog-Altatec, Xive - Friadent Dentsply, Sky Implant - Bredent, u.a.

• Plate thickness: 0.6 mm

Ø 3.3

8 10

Ø 3.3

8 10

Ø 3.6

8 10

Ø 3.6

8 10

MONDEAL

Page 12

SWING-LIFT Instruments

18-33001 Swing-Lift instrument no.1, small hook, angled

18-33002 Swing-Lift instrument no. 2, hook, angled

18-33003 Swing-Lift instrument no. 3, spatula, straight/angled

18-33004 Swing-Lift instrument no. 4, spoon/condenser

18-33000 Swing-Lift Set, instruments I-4, complete (not illustrated)

The SWING-LIFT Instrument set for the direct sinus-lift increases the sensitivity during operation and reduces the risk of perforating the „Scheiderian membrane“ - due to the unique swing-effect of the instruments no. 1, 2 and 3.

MONDEAL

Page 13

ARCS PIN

31-01203 Titanium Pins 3 mm, with thread, 5/ea. 31-01213 Titanium Pins 3 mm, without thread, 5/ea.

31-01205 Titanium Pins 5 mm, with thread, 5/ea. 31-01215 Titanium Pins 5 mm, without thread, 5/ea.

31-01255 Drill for pins and foils, DENTAL 31-01226 Blade for Titanium Pins, DENTAL

31-01075 ARCS Membrane Perforator and spatula, 18 cm

31-01230 Tray for 15 Titanium Pins 33-18235 Thumb Screw Mandrel for Dental shaft instruments

24-30552 Mallet for placing the pins, 140 g, 21 cm

MONDEAL

Page 14

ARCS PIN

31-01220 Pin Placement Instrument straight, complete, 3 parts

31-01219 Pin Placement Instrument angled, complete, 3 parts

31-01223 Handle for Placement Instrument

31-01222 Placement adaptor straight for Placement Instrument, with cover cap

31-01221 Placement adaptor angled for Placement Instrument, with cover cap

31-01224 Cover cap for Placement Instrument

MONDEAL

Page 15

Container

31-TD5-2001 ARCS tray for instruments and implants

Am Gewerbering 7 • 78570 Mühlheim a. d. Donau/GermanyPhone +49 7463 99307 0 • Fax +49 7463 99307 33 • mail@mondeal.de

High Quality Implants

Made by MONDEAL

We reserve the right to make catalog and design changes arising from further developments and modifications. Pictures, product descriptions and texts are the property of MONDEAL Medical Systems GmbH. Further use and reproduction by Third Parties requires written consent from MONDEAL Medical Systems GmbH. All rights re-served! Note: Responsibility for the selection of the patient, for adequate training as well as the decision as to the choice and use of the implants, a post-operative removal or retention of implants is the sole decision of the surgeon. All brands and logos referred to in this brochure, registered by Third Parties, are subject without restriction to the legal provisions currently in force and to the rights of ownership of the respective registered owner.© 2011 - MONDEAL Medical Systems GmbH

97-D

105-

E AR

CS

01/ 0

4-11