509_sales

DEEP SEA ELECTRONICS

509AUTO MAINS

FAILURE

The configurable Automatic MainsFailure Model 509 allows many ofthe industry’s demandingspecifications to be acheived.Variations of the unit offer additionalfunctions such as the RS232interface for remote monitoring by avolt free relay module, annunciator orbuilding management system.

The 509 is used to start a generatoron a mains (utility) failure, andtransfer the load when the engine’soperating criteria has been met. Onrestoration of the mains (utility)supply, the engine is returned tostandby mode.

Operation of the module is via a fourposition rotary switch (key-switchoption available) mounted on thefront panel with STOP, AUTO,MANUAL (Off-load run) and TEST(on-load run) positions.

Once activated, the 509 modulecarries out all the start and stopprocedures of the engine, indicatingoperational status and faultconditions, and automaticallyshutting down the engine , givingtrue first up fault condition of theengine failure. The information isdisplayed on an illuminated LiquidCrystal Display on the front panel.

Text and selective operationalsequences can be altered using the801 Calibration Unit. Adjustableparameters are displayed on thescreen when the CONFIGURATIONmode is activated.

Access to the critical operationalsequences and timers, for use byrestricted personnel, are barred by asecurity code.

Relay outputs are provided for FuelSolenoid Output, Start Output, AlarmOutput and one configurable output.The configurable relay is usuallyconfigured as pre-heat, however thisfunction can be changed to activate ona range of 6 different functions,conditions or alarms. The relayssupply positive plant supply out.

Configurable inputs are available forLow Oil Pressure or High EngineTemperature, allowing the module tofunction with N/O or N/C switches.Three fully configurable auxiliaryinputs are provided to give protectionexpansion. These can be selected tobe indication, warning or shutdowninputs either immediate or held offduring start up. Alternatively they maybe configured to provide additionalcontrol features to the module.

The 500 series modules have beendesigned for front panel mounting.The module is fitted into the panel cut-out with the fixing clips removed.These are then fitted from the rear.Connection is via locking plug andsocket connectors.

FEATURES

Ø Under/over speed shutdownØ Under/over frequency shutdown

Ø Low oil pressure shutdownØ Adjustable crank cycle/attemptsØ External remote start input

Ø Magnetic pick-up or alternator speedmonitoring

Ø 3 digital inputs – fully userconfigurable

Ø Configurable relay output

Ø LCD back-lighting for low light-leveloperation

DESCRIPT ION

SPECIF ICATION

DC Supply:8 to 35 V Continuous.Cranking Dropouts:Able to survive 0 V for 50 mS,providing supply was at least 10 Vbefore dropout and supply recoversto 5V. This is achieved without theneed for internal batteries.Mains Input Range:100 - 300 V ac RMSMains Trip Range:75 - 275 V ac RMSAlternator Input Range:15 - 300 V ac RMSAlternator Input Frequency:50 - 60 Hz at rated engine speed.Magnetic Input Range:0.5 V to +/- 70 V (Clamped bytransient suppressors)Magnetic Pickup InputFrequency:2300Hz to 6000 Hz atrated engine speed.Start/Fuel Relay Output:16 Amp DC at supply voltage.Auxiliary/Alarm Relay Outputs: 6 Amp DC at supply voltage.Contactor Relay Outputs:8 Amp RMS AC at Mains voltage.Dimensions:144mm x 72mm x141mm5.7’’ x 2.8’’ x 5.5’’(Excluding Key-switch)Charge Fail / Excitation Range:0 V to 35 VOperating Temperature Range:-10° to +60°C

Issue 3VH 05/02/03

Deep Sea Electronics plc reserve the right tochange specification without notice.

CASE DIMENSIONS

TYPICAL CONNECTIONS

72.0mm

144.0mm

65.5mm

133.0mm

7.5mm

MAINS VOLTTRIP

OPTIONALRS232

Panel cutout138.5mm x 68.0mm (5.5” x 2.7”)

5.2” 5.7”

0.3”

2.8”

2.6”