advanced rfic design elen359, lecture 4: frequency multipliers · 2004. 4. 7. · frequency...

Advanced RFIC Design ELEN359A, Lecture 4: Frequency TranslationInstructor: Dr. Allen A Sweet

Copy Right 2004

Types of Frequency Translation

• Multipliers: No LO signal required, but High power drive signal is required (I.e. high DC current), high conversion loss.

• Translators: Convert any frequency to any other frequency, either up or down. Low drive power (low DC current), conversion gain. Requires a stable LO signal (PLL).

Copy Right 2004

Types of Multipliers

• Differential to Single Ended Diode Doublers

• Full Differential Diode Doublers• Single Ended Diode Tripler's• Gilbert Cell Doublers• Gilbert Cell Tripler's

Copy Right 2004

Diode IV Characteristics

Copy Right 2004

Diode Curve Schematic Diagram

Copy Right 2004

VBIC Diode IV

Copy Right 2004

Single Ended Diode Doubler

Copy Right 2004

Half sine Waves are Rich in secondHarmonic

ADS Model of a Single Ended Diode Doubler

Copy Right 2004

HB Controller and Sources for Diode Doubler

Copy Right 2004

ADS Simulations of a Single Ended Diode Doubler

Pout @ 2FIs 0 dBm

Copy Right 2004

Differential Diode Doubler

Copy Right 2004

ADS Model for a Full Differential Diode Doubler

Copy Right 2004

HB Controller and Sources for Differential Diode Doubler

Copy Right 2004

ADS Simulation of a Fully Differential Diode Doubler

Copy Right 2004

Pout @ 2F Is 0 dBm

(Requires a+20 dBm Drive signalWhich takes100 mA DC Current at 30% eff)

Single Ended Diode Tripler

Copy Right 2004

ADS Model for a Single Ended Diode Tripler

Copy Right 2004

HB Controller and Sources for Diode Tripler

Copy Right 2004

ADS Simulation of a Single Ended Diode Tripler

(No naturalSuppression ofFundamental)

Symmetric Clipping of Wave form byBack to backdiodes

Copy Right 2004

Gilbert Cell Doubler

Copy Right 2004

ADS Schematic of a Gilbert Cell Doubler

Copy Right 2004

Source Configuration

Copy Right 2004

HB Controller Setup

Copy Right 2004

Gilbert Cell Doubler SimulationMany mixingProducts Contribute

(Use highOrder # in simulations)Copy Right 2004

Simulated Gilbert Doubler by “Hard Wiring” RF and LO ports

Copy Right 2004

Simulation of “hard wired input” Gilbert Cell Doubler

(Add 3 dB to include LOSignal loss:gain=-4.287)

Copy Right 2004

Gilbert Cell Tripler

Copy Right 2004

Sources and HB Controller for Gilbert Cell Tripler

RF_freq=2 X LO_freq

(Use high order)

Copy Right 2004

Copy Right 2004

Simulation of Gilbert Cell Tripler

Many mixer productsContribute to tripling

Translators

• No harmonic relationships between the input and the output Frequencies.

• Up Converting Translators• Down Converting Translators• Requires a PLL LO Signal

Copy Right 2004

Gilbert Cell Down and up Converters

(i.e. +/-F2+/- F1)

Copy Right 2004

Translate Wi-Fi (B) Down to Wi-Fi (A) with a Gilbert Cell Mixer

(Use high side LO)

Flo=Frf + Fif=2.5 GHz + 5.5 GHz=8.0 GHz

Copy Right 2004

Sources

Copy Right 2004

Output BPF

Copy Right 2004

ADS Simulation of Down Converting Wi-Fi Translator

Copy Right 2004

Up Convert Cellular 850 MHz to PCS 1900 MHz

Flo=-Frf + Fif = .85 + 1.9 = 1.05

Copy Right 2004

Sources

Copy Right 2004

BPF at the Output

Copy Right 2004

ADS Simulations of Up Converting Frequency Translator

Copy Right 2004

Homework #4: Simulate a Wi-Fi Frequency Translator

• Design an Up Converting Frequency Translator from Wi-Fi A (2.4 GHz) to Wi-Fi B (5.8 GHz). The Translator shall have at least 25 dB gain, requiring either a pre or a post amplifier.

• All Spurs from 3.0 GHz to 7.0 GHz will be down by at least –40 dBc. You must design the filter.

• Make design decisions on the basis of lowest possible DC current.

Copy Right 2004