laminex® wall panel
Post on 06-Feb-2017
228 Views
Preview:
TRANSCRIPT
LAMINEX® WALL PANELSOLUTIONS
FABRICATION AND INSTALLATION GUIDE
IMPORTANT NOTES
1. Suitable for internal use only
2. Failure to install or maintain this product in accordance with applicable building codes, regulations, standards and
Laminex’s instructions may lead to personal injury, affect system performance, violate building codes and void the
product warranty.
3. Laminex will only warrant the system when used with tested and approved Laminex decorative panels. For Laminex
panels not featured in the matrix, refer to your Laminex Representative for more information.
4. The strength of the system is dependant on the installer ensuring that all fasteners are firmly screwed to framework.
5. All panels should be pre-conditioned on-site for 48 hours before hanging.
RESPONSIBILITY
The specifier or person responsible for the project must ensure that the details in this instruction are appropriate for the
intended application and that additional detailing is performed for details that are not specified in these instructions.
FRAMING
Framing tolerances must be within 3mm over any 3000mm length of the frame. Frame must be square, straight and true.
Timber
All frames must be constructed in accordance with AS/NZS 1684 and be 35mm or wider. Ensure that all fasteners used
penetrate framing by at least 30mm.
Steel
All frames must be constructed in accordance with NASH standard Part 1.
Using Button-Fix over existing internal linings
Ensure that all fasteners used penetrate existing linings and are firmly screwed into studwork by at least 30mm. Laminex
recommends that wooden battens of 35mm x 45mm pine or 16mm MDF are used over existing plaster or masonary wall
linings.
Bracing
Laminex Button-Fix is not suitable for the provision of any bracing load resistance.
HOW IT WORKS
ATTACHING THE BUTTON
Choose an appropriate 5mm counter sunk screw to
provide >30mm engagement into the supporting structure.
NOTE: Plasterboard is not strong enough to support a
Laminex Decorative panel with Button-Fix. Secure Buttons
into studwork or battens only.
IMPORTANT: The integrity of the Laminex Wall Panel Solutions system is dependant on the installer providing a sound
support to the system such as stud work, framing or battens.
TYPE 2 FIX
The Type 2 Fix connects panels at
90° with a simple push/pull fit. It
is ideal for applications where the
emphasis is more on ease of fit
and less on strength. Unlike Type 1,
the Type 2 Fix does not require a
15mm dropdown engagement.
TYPE 1 FIX
The Type 1 Fix connects parallel
panels and is ideal for applications
where strength and security are
paramount.
Engage the Buttons in the Fixes and
slide the panel down by 15mm until
Button-fix goes ‘click’. The Type 1 Fix
can also be configured for sideways
assembly.
When surface-mounted, the Type
1 Fix creates an 8mm gap between
the two attaching panels.
Alternatively, you can rebate the Type
1 Fix, to reduce the gap between the
two attaching panels to only 3mm.
Do not use the REBATE method with Compact Laminate – as this reduces the systems tolerance to changes in panel dimensions as humidity changes.
Ø5mm pan head wood screws for surface-mounted Fix
15mm fall to engage panel
Panel drilling
Ø4.5mm countersunk wood screws for rebated Fix
Lime green Button for use with Ø5mm countersunk wood screw
Orange Button for use with Ø6.2mm Varianta Euro screw
Ø4.5mm pan head wood screws for Fix
Ø5mm pan head wood screws for surface-mounted Fix
15mm fall to engage panel
Panel drilling
Ø4.5mm countersunk wood screws for rebated Fix
Lime green Button for use with Ø5mm countersunk wood screw
Orange Button for use with Ø6.2mm Varianta Euro screw
Ø4.5mm pan head wood screws for Fix
Ø5mm pan head wood screws for surface-mounted Fix
15mm fall to engage panel
Panel drilling
Ø4.5mm countersunk wood screws for rebated Fix
Lime green Button for use with Ø5mm countersunk wood screw
Orange Button for use with Ø6.2mm Varianta Euro screw
Ø4.5mm pan head wood screws for Fix
Ø5mm pan head wood screws for surface-mounted Fix
15mm fall to engage panel
Panel drilling
Ø4.5mm countersunk wood screws for rebated Fix
Lime green Button for use with Ø5mm countersunk wood screw
Orange Button for use with Ø6.2mm Varianta Euro screw
Ø4.5mm pan head wood screws for Fix
Ø5mm pan head wood screws for surface-mounted Fix
15mm fall to engage panel
Panel drilling
Ø4.5mm countersunk wood screws for rebated Fix
Lime green Button for use with Ø5mm countersunk wood screw
Orange Button for use with Ø6.2mm Varianta Euro screw
Ø4.5mm pan head wood screws for Fix
Ø5mm pan head wood screws for surface-mounted Fix
15mm fall to engage panel
Panel drilling
Ø4.5mm countersunk wood screws for rebated Fix
Lime green Button for use with Ø5mm countersunk wood screw
Orange Button for use with Ø6.2mm Varianta Euro screw
Ø4.5mm pan head wood screws for Fix
Ø5mm pan head wood screws for surface-mounted Fix
15mm fall to engage panel
Panel drilling
Ø4.5mm countersunk wood screws for rebated Fix
Lime green Button for use with Ø5mm countersunk wood screw
Orange Button for use with Ø6.2mm Varianta Euro screw
Ø4.5mm pan head wood screws for Fix
Ø5mm pan head wood screws for surface-mounted Fix
15mm fall to engage panel
Panel drilling
Ø4.5mm countersunk wood screws for rebated Fix
Lime green Button for use with Ø5mm countersunk wood screw
Orange Button for use with Ø6.2mm Varianta Euro screw
Ø4.5mm pan head wood screws for Fix
THE SECRET FIXING FOR PANELS
The Button-fix range of fasteners
and accessories is:
BUTTONS
1. Lime green Button for
countersunk (5mm) wood
screws.
2. Orange buttons for Euro
screws/varianta. (Diameter
6.2mm countersunk).
FIXES
3. Type 1 Fix for connecting parallel
panels. (Diameter 5mm pan head
for face fixing. Diameter 4.5mm
countersunk for rebated fixing.)
4. Type 2 Fix for connecting 90°
panels. (Diameter 4.5mm pan
head.)
MARKER ACCESSORIES
5. Button marker accessory for
use with Type 1 Fixes.
6. Fix marker accessory for use
with Type 2 Fixes (and can also
be used with Type 1).
Marker accessories need to be
ordered separately from the
Button-fixes.
OTHER ACCESSORIES
7. Security cord accessory for use
with Type 2 Fixes.
8. Router jig for use when
recessing Type 1 Fixes.
These accessories need to be
ordered separately from the
Button-fixes.
1. 2.
5. 6.
3. 4.
7. 8.
ACCESSORIES
BUTTON MARKER
This re-usable accessory helps to
accurately align the Buttons with
Type 1 Fixes. Snap a marker into
each Fix, then position the second
panel and press firmly. The markers
will leave indents in the panel
surface, which can be used as pilot
guides for the Buttons.
SECURITY CORD ACCESSORY
This accessory should be installed with the Type 2 Fix in situations where safety
is an issue. On a vertical panel install two Security Cords, one to each Fix in the
top corners.
An additional Button is used to capture the loop on the Security Cord, installed
adjacent to the fixing Button. To remove the panel completely, ease the loop on
the Security Cord off the Button.
Please note that accessories must be ordered separately from the Button-fixes.
FIX MARKER
This re-usable accessory helps to
accurately align Type 2 Fixes. The
marker is assembled onto the Fix
and used to position the Button
from the panel edge. After fixing
the Button, position the second
panel and press firmly. The marker
will leave indents in the panel
surface, which can be used as
guides when drilling pilot holes for
the Fix.
The marker can be used for
internally mounted panels, but
must be assembled in the opposite
orientation, as shown on the right.
Tip: use some adhesive tape to
stop the marker and Fix assembly
rotating on the Button.
INSTRUCTIONS FOR USE – TYPE 1 FIX SETS
Button-fix is designed for furniture construction and interior fittings.
Provided that the screws and substrate are properly matched, a vertical panel fixed with four Type 1 Fixes can safely weigh
200kg. For critical applications it is essential to perform your own tests.
Avoid any contact with aggressive solvents and cleaning products.
SUGGESTED LAYOUT– MDF, PB & PLYWOOD
As an approximate guide, we suggest
that Button-fix centres are no greater
than 1000mm apart and no closer
than 35mm to the edge of the panel.
Always remember to allow at least
15mm clearance for the removable
panel to disengage.
Allow 3mm space minimum
between panels.
SUGGESTED LAYOUT– COMPACT LAMINATE
As an approximate guide, we suggest
that Button-fix centres are no greater
than 450mm apart and no closer
than 35mm to the edge of the panel.
Always remember to allow at least
15mm clearance for the removable
panel to disengage.
Allow 5mm space minimum
between panels.
Lime green Button for use with Ø5mm countersunk wood screw
Orange Button for use with Ø6.2mm Varianta Euro screw
MAX 1000
MAX 1000
MAX 1000
Lime green Button for use with Ø5mm countersunk wood screw
Orange Button for use with Ø6.2mm Varianta Euro screw
MAX 450
MAX 450
MAX 450
2700
600
2400
1200
Max1000
Max1000
Max300
Max300
2700
600
2400
1200
Max450
Max450
Max200
Max200
2700
600
2400
1200
Max1000
Max1000
Max300
Max300
2700
600
2400
1200
Max450
Max450
Max200
Max200
INSTRUCTIONS FOR USE – TYPE 1 FIX SETS
BUTTON MARKER ACCESSORY
The Button marker accessory helps to mark out where to install the Buttons.
Once you have attached the Fix mouldings (see following pages), snap a marker into each one. Then position the second panel
and press firmly. The markers will leave indents in the panel surface, which can be used as guides for drilling pilot holes for the
Buttons.
Remove the markers, which can be re-used to mark out the next panel.
Lime green Button for use with Ø5mm countersunk wood screw
Orange Button for use with Ø6.2mm Varianta Euro screw
MAX 1000
MAX 1000
MAX 1000
Lime green Button for use with Ø5mm countersunk wood screw
Orange Button for use with Ø6.2mm Varianta Euro screw
MAX 1000
MAX 1000
MAX 1000
SURFACE-MOUNTED FIX
Surface mounting creates an 8mm gap between the two panels. The Fix can be configured in three options:
1. BUTTON ON REMOVABLE PANEL
The Fix is attached to the background structure, pointing upwards as shown in the diagrams on the right.
In this configuration, the panels engage vertically and 15mm clearance is required above the removable panel.
2 x Ø5mm pan head wood screws
15mm fall to engage panel
2 x Ø5mm pan head wood screws
2 x Ø5mm pan head wood screws
15mm slide to engage panel
Panel drilling
Panel drilling
15mm fall to engage panel
Panel drilling
2 x Ø5mm pan head wood screws
15mm fall to engage panel
2 x Ø5mm pan head wood screws
2 x Ø5mm pan head wood screws
15mm slide to engage panel
Panel drilling
Panel drilling
15mm fall to engage panel
Panel drilling
2 x Ø5mm pan head wood screws
15mm fall to engage panel
2 x Ø5mm pan head wood screws
2 x Ø5mm pan head wood screws
15mm slide to engage panel
Panel drilling
Panel drilling
15mm fall to engage panel
Panel drilling
INSTRUCTIONS FOR USE – TYPE 1 FIX SETS
2. FIX ON REMOVABLE PANEL
The Fix is attached to the removable panel, pointing downwards as shown in the diagrams on the right.
In this configuration, the panels engage vertically and 15mm clearance is required above the removable panel.
3. SIDEWAYS ARRANGEMENT
The Fix is attached to either the background structure or the removable panel, pointing sideways as shown in the diagrams on
the right.
In this configuration, the panels engage horizontally and 15mm clearance is required to the side of the removable panel.
NOTE: Sideways arrangements are NOT suitable for Compact Laminate panels orientated vertically and over 1.2m wide.
Compact Laminate needs to be able to change dimensions as ambient humidity changes.
4. OVERHEAD & CEILING ARRANGEMENTS
Laminex does NOT consider Button-Fix suitable for ceiling or overhead installation of decorative panels.
2 x Ø5mm pan head wood screws
15mm fall to engage panel
2 x Ø5mm pan head wood screws
2 x Ø5mm pan head wood screws
15mm slide to engage panel
Panel drilling
Panel drilling
15mm fall to engage panel
Panel drilling
2 x Ø5mm pan head wood screws
15mm fall to engage panel
2 x Ø5mm pan head wood screws
2 x Ø5mm pan head wood screws
15mm slide to engage panel
Panel drilling
Panel drilling
15mm fall to engage panel
Panel drilling
2 x Ø5mm pan head wood screws
15mm fall to engage panel
2 x Ø5mm pan head wood screws
2 x Ø5mm pan head wood screws
15mm slide to engage panel
Panel drilling
Panel drilling
15mm fall to engage panel
Panel drilling
2 x Ø5mm pan head wood screws
15mm fall to engage panel
2 x Ø5mm pan head wood screws
2 x Ø5mm pan head wood screws
15mm slide to engage panel
Panel drilling
Panel drilling
15mm fall to engage panel
Panel drilling
2 x Ø5mm pan head wood screws
15mm fall to engage panel
2 x Ø5mm pan head wood screws
2 x Ø5mm pan head wood screws
15mm slide to engage panel
Panel drilling
Panel drilling
15mm fall to engage panel
Panel drilling
2 x Ø5mm pan head wood screws
15mm fall to engage panel
2 x Ø5mm pan head wood screws
2 x Ø5mm pan head wood screws
15mm slide to engage panel
Panel drilling
Panel drilling
15mm fall to engage panel
Panel drilling
INSTRUCTIONS FOR USE – TYPE 1 FIX SETS
REBATED FIX
Rebating the Fix creates a 3mm gap between the two panels. The Fix can be configured in three options:
1. BUTTON ON REMOVABLE PANEL
The Fix is attached to the background structure, pointing upwards as shown in the diagrams on the right.
In this configuration, the panels engage vertically and 15mm clearance is required above the removable panel.
2 x Ø4.5mm countersunk wood screws
2 x Ø4.5mm countersunk wood screws
2 x Ø4.5mm countersunk wood screws
15mm slide to engage panel
Panel drilling
15mm fall to engage panel
15mm fall to engage panel
Panel
drilling
Panel
drilling
2 x Ø4.5mm countersunk wood screws
2 x Ø4.5mm countersunk wood screws
2 x Ø4.5mm countersunk wood screws
15mm slide to engage panel
Panel drilling
15mm fall to engage panel
15mm fall to engage panel
Panel
drilling
Panel
drilling
2 x Ø4.5mm countersunk wood screws
2 x Ø4.5mm countersunk wood screws
2 x Ø4.5mm countersunk wood screws
15mm slide to engage panel
Panel drilling
15mm fall to engage panel
15mm fall to engage panel
Panel
drilling
Panel
drilling
2 x Ø4.5mm countersunk wood screws
2 x Ø4.5mm countersunk wood screws
2 x Ø4.5mm countersunk wood screws
15mm slide to engage panel
Panel drilling
15mm fall to engage panel
15mm fall to engage panel
Panel
drilling
Panel
drilling
2 x Ø4.5mm countersunk wood screws
2 x Ø4.5mm countersunk wood screws
2 x Ø4.5mm countersunk wood screws
15mm slide to engage panel
Panel drilling
15mm fall to engage panel
15mm fall to engage panel
Panel
drilling
Panel
drilling
2 x Ø4.5mm countersunk wood screws
2 x Ø4.5mm countersunk wood screws
2 x Ø4.5mm countersunk wood screws
15mm slide to engage panel
Panel drilling
15mm fall to engage panel
15mm fall to engage panel
Panel
drilling
Panel
drilling
2. FIX ON REMOVABLE PANEL
The Fix is attached to the removable panel, pointing downwards as shown in the diagrams on the right.
In this configuration, the panels engage vertically and 15mm clearance is required above the removable panel.
NOTE: REBATED FIX method is NOT suitable for Compact Laminate mounting. Compact laminate needs air flow on both
sides of the panel and room to change dimensions by ~2.5% as ambient humidity changes.
All battens behind compact laminate must be orientated vertically to allow for ventilation.
INSTRUCTIONS FOR USE – TYPE 1 FIX SETS
A USEFUL TIP
When several Button-fixes are used on a panel or if you require the panel to
be easily removable, you can reduce the strength of the click-fit.
To achieve this adapt some (but not all) the Fix mouldings by popping out
the ears with a flat screw driver, as shown in the diagram on the right. Wear
eye protection and gloves.
BUTTON DIMENSIONS FIX DIMENSIONS
3. SIDEWAYS ARRANGEMENT
The Fix is attached to either the background structure or the removable panel, pointing sideways as shown in the diagrams on
the right.
In this configuration, the panels engage horizontally and 15mm clearance is required to the side of the removable panel.
2 x Ø4.5mm countersunk wood screws
2 x Ø4.5mm countersunk wood screws
2 x Ø4.5mm countersunk wood screws
15mm slide to engage panel
Panel drilling
15mm fall to engage panel
15mm fall to engage panel
Panel
drilling
Panel
drilling
2 x Ø4.5mm countersunk wood screws
2 x Ø4.5mm countersunk wood screws
2 x Ø4.5mm countersunk wood screws
15mm slide to engage panel
Panel drilling
15mm fall to engage panel
15mm fall to engage panel
Panel
drilling
Panel
drilling
2 x Ø4.5mm countersunk wood screws
2 x Ø4.5mm countersunk wood screws
2 x Ø4.5mm countersunk wood screws
15mm slide to engage panel
Panel drilling
15mm fall to engage panel
15mm fall to engage panel
Panel
drilling
Panel
drilling
SUGGESTED JOIN DETAILS
LAP JOIN
LAP JOIN
The following diagrams offer suggestions for panel joins.
SEALED TONGUE AND GROOVE JOIN
Decorative panel
MDF, metal or HPL tongue
Flexible Sealant
Decorative panel
MDF, Metal or HPL tongue
Screw fixing
Decorative panel
HPL or Metal reveal
TONGUE AND GROOVE JOIN
Decorative panel
Paint for MDF & Plywood
CORNER DETAIL
Decorative panel
Screw fixing
HPL or Metal reveal
NOTE: Compact Laminate requires airflow on both sides of the panel and an allowance of 5mm between panels for
expansion and contraction. MDF PB requires 3mm gap between panels. All boards should be pre-conditioned on-site for
48 hours before hanging.
For more information visit laminex.com.au or call 132 136.
Laminex Wall Panel Solutions Button-Fix is marketed and distributed by Laminex ABN 98 004 093 092. The colours of the products featured within the imagery in this brochure are as close to the Laminex Wall Panel Solutions Button-Fix range as photographic lighting and modern printing processes allow. Laminex®, Button-Fix™
2/1
4 T
LG13
01
1. Subject to the conditions and limitations set out in this warranty below, Laminex Group Pty Limited ABN 98 004 093 092 trading as Laminex warrants to the original purchaser of any Laminex® Wall Panel Solutions Button-Fix™ for interior residential or commercial use who is a “consumer” as defined in section 3 of the Australian Consumer Law that Laminex will at its option, repair or replace any Laminex Wall Panel Solutions Button-Fix without charge if it is defective directly as a result of its manufacture by Laminex or it’s suppliers, or the materials used in its manufacture by Laminex or it’s suppliers, during the first seven years after the initial purchase (proof of purchase will be required). Subject to paragraph 7, this obligation terminates at the expiration of 7 years from the date of purchase of the product concerned from Laminex.
2. This warranty does not cover any defect caused by: a) any natural occurrence or any other circumstance beyond Laminex’s control; or b) failure to follow any procedures recommended by Laminex, at the time of
fabrication and installation, for the fabrication and installation of Laminex Wall Panel Solutions Button-Fix; or
c) physical abuse, misuse, accidents, exposure to excessive heat, exposure to excessive moisture, the use of solvents or inappropriate cleaning products/materials, improper maintenance, normal ‘wear and tear’, burns, exposure to chemical products; or
d) general fading and discolouration (exposure to sunlight should be avoided); or e) the product being used in applications that are not recommended by Laminex in the
product literature published; or f) where the defect has been caused by faulty workmanship by any person other
than Laminex; or g) variation in colour, pattern, shade of the material against the sample material, displays
and/or printed illustrations The warranty also does not cover: h) where the defect is trivial or insubstantial; or i) where, as at the date of notification of the defect to Laminex, the defective
product no longer forms part of Laminex’s standard stock range and the person complaining of the defect does not agree to the supply of a replacement which is as close a type as is possible from Laminex’s then prevailing stock range; or
j) anything that has been disclosed as a feature or limitation of Laminex Wall Panel Solutions Button-Fix in any literature published by Laminex; or
k) use of Laminex Wall Panel Solutions Button-Fix with panels other than the recommended Laminex Decorative Panels, as the Laminex Wall Lining system has been tested as a system incorporating appropriate Laminex Decorative Panels;
3. This warranty applies only to Laminex Wall Panel Solutions Button-Fix: a) Purchased from Laminex after 1 July 1994 for interior residential or commercial
use in Australia; b) That has remained installed at the location at which it was first installed after its
sale by Laminex; c) Which has been installed, maintained, used and protected in the manner
recommended by Laminex, as at the relevant time of such installation, maintenance, use or protection, in its literature published from time to time concerning Laminex Wall Panel Solutions Button-Fix, a copy of which may be obtained, free of charge, at the point of purchase or by writing directly to Laminex at the address given below; and
d) where Laminex has been notified of the defect within seven days of the first person to become aware of it.
4. Costs of claiming:a) Laminex will bear the expense of the reasonable labour charges which are necessary
for the repair or replacement of the Laminex Wall Panel Solutions Button-Fix Product covered by this warranty. When submitting a claim, please provide details of the quantum of the labour charges necessary for the repair or replacement of the Laminex Wall Panel Solutions Button-Fix (including any quotes you have obtained verifying the labour charges).
b) If Laminex considers that you have incurred or will incur reasonable labour charges which are necessary for the repair or replacement of the Laminex Wall Panel Solutions Button-Fix covered by this warranty, it will pay you the amount of those charges or pay those charges directly to a third party to undertake the necessary repair or replacement works.
c) Subject to a), the person claiming the warranty will bear all other expenses of claiming the warranty.
5. A replacement product may not be reasonably available from Laminex in the same shape, type or colour as the original Laminex Wall Panel Solutions Button-Fix product covered by this warranty. If a replacement product of the same shape, type or colour is not reasonably available, Laminex reserves the right to provide a replacement product of as close a shape, type and colour match as is reasonably possible from Laminex’s then prevailing product range in satisfaction of its obligations under this warranty.
6. Except as expressly provided in paragraphs 8 and 9, all terms, conditions, warranties, undertakings, inducements and representations, whether express or implied, statutory or otherwise relating in any way to Laminex Wall Panel Solutions Button-Fix are excluded. Without limiting the generality of the preceding sentence, Laminex will not be under any other liability in respect of any loss or damage (including consequential loss or damage) however caused (whether by negligence or otherwise) which may be suffered or incurred or which may arise directly or indirectly in respect of Laminex Wall Panel Solutions Button-Fix.
7. Where any applicable legislation implies any term, condition or warranty into the contract of sale between Laminex and a person, or Laminex’s relationship with a person, which has acquired Laminex Wall Panel Solutions Button-Fix, or otherwise gives that person a particular remedy against Laminex, and that legislation or any legislation voids or prohibits any provision excluding, or modifying the application of, or exercise of, any liability under such term, condition, warranty or remedy, then that term, condition warranty or remedy shall be deemed to be included in or, as the case may be, apply to that contract or relationship. However, Laminex’s liability for any breach of such term, condition or warranty or under such remedy, shall be limited, at Laminex’s option, in any one or more of the ways permitted by that legislation including, where so permitted:
a) If the breach related to Laminex Wall Panel Solutions Button-Fix:i. The replacement of Laminex Wall Panel Solutions Button-Fix or the supply of
equivalent product;ii. The repair of Laminex Wall Panel Solutions Button-Fix;iii. The payment of the cost of replacing Laminex Wall Panel Solutions Button-Fix or
acquiring equivalent product; oriv. The payment of the cost of having Laminex Wall Panel Solutions Button-Fix
repaired; and b) If the breach relates to services: i. The supplying of the services again; or ii. The payment of the cost of having the services supplied again.8. Please note that the benefits given by this warranty are in addition to other rights and
remedies of the person under a law in relation to the goods or services to which this warranty relates. This warranty should not therefore be read as an exclusive statement of the rights of the original purchaser or any other person.
9. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
10. This warranty does not cover any other product used or installed in connection with Laminex Wall Panel Solutions Button-Fix.
11. This warranty is not transferable or assignable.12. Any inquiries regarding this warranty should be sent to Laminex Wall Panel Solutions
Button-Fix Warranties, Laminex, P.O. Box 407, Doncaster, VIC 3108. Inquiries can also be made by calling 132 136 or emailing enquiries@laminex.com.au.
13. To claim this warranty, please send the following written details to the address set out above:• Your name, address and telephone number• Place where the Laminex Wall Panel Solutions Button-Fix Product was purchased
and amount you paid for it. Please also provide a copy of your proof of purchase• If the Laminex Wall Panel Solutions Button-Fix Product has been installed - the
address at which it was installed, the date of installation, the name of the person and company that installed it, the quantum of the labour charges necessary for the repair or replacement of the Laminex Wall Panel Solutions Button-Fix Product (including any quotes you have obtained verifying the labour charges)
• Description of how the Laminex Wall Panel Solutions Button-Fix Product is defective and when you found out that it was defective. Please also provide any photographs taken of the defect(s)
After we receive your written claim, we will contact you to discuss. In some circumstances Laminex may need to remove a sample of the installed Laminex Wall Panel Solutions Button-Fix Product for testing.
7 YEAR WARRANTY
top related