lenox boardwalk erollins@interceramic.com project information lenox boardwalk development 1500 south...

A Division of ACI Group, LLC1012 Mopac Circle · Suite 200 · Austin, Texas 78746 · (512) 328-1883 (FAX) 328-7448 · www.ppds-inc.com

Austin, Texas 78741

Construction Set: October 1, 2015

1500 South Pleasant Valley

LENOX BOARDWALKAPARTMENTS

SPECIFICATIONSPricing Set: June 8, 2015

[ UNIT ]

LENOX BOARDWALK TABLE OF CONTENTS

1. GENERAL FINISH NOTES 2. FLOORING FINISHES 3. BASE & TRIM FINISHES

4. PAINT & WALL FINISHES 5. MILLWORK FINISHES 6. LIGHT FIXTURES 7. PLUMBING FIXTURES 8. BATH ACCESSORIES 9. DOOR STYLE & HARDWARE 10. MISCELLANEOUS

[ UNIT ]

GENERAL FINISH NOTES

1. Contractor to provide all specified finish material submittals to Interior

Designer for approval prior to ordering. Any suggested alternate finishes to be submitted to Interior Designer for approval.

2. All paint & stain samples to be sampled at jobsite for Interior Designer

approval prior to painting full project. 3. Paint quality & application / preparation methods included. 4. Alternates will not be accepted on specified materials without the approval

of the Interior Designer. 5. All finish specifications and finish materials must be cross-checked and

verified by subcontractors prior to ordering. Any discrepancies require notification to the Interior Designer and the General Contractor prior to installation of materials.

6. "unless noted otherwise" will be abbreviated as "u.n.o." within this

specification manual. 7. Coordinate location of pendant light fixtures on site with Interior Designer

prior to installation. 8. Refer to manufacturer’s recommended installation methods for all finish

materials included in this package. 9. Re-use of enclosed specifications and corresponding documents for

purposes other than the above referenced project are forbidden without written permission of PPDS.

[ UNIT ]

Project Information

Lenox Boardwalk Development 1500 South Pleasant ValleyAustin, Texas 78741

Project Designer Information

Lead Designer:Janna Paulson, IIDA, LEED APjanna@ppds-inc.com

UNITFLOORING FINISHES

[ UNIT ]

Location: All Units Bedrooms and ClosetsAll Upper Level Units Living and Dining Areas

Description: Broadloom CarpetManufacturer: Mohawk Properties CollectionStyle: Hounds RunColor: 718 Mushroom CapWidth: 12' BroadloomFiber: 75%SmartStrand Nanoloc BCF Triexta

25% BCF P.E.T.Weight: 25ozLEED Info: Green Label Plus CertifiedInstallation: Over 1/2" 5Lbs. Pad

Notes:**Refer to Architectural Unit Sheets for location.**All 1st Level Unit Living Rooms and Dining Rooms will receive vinyl plank flooring.

**Carpet pad to be Green Label Plus Certified**No Carpet is to be installed within 3'-0" of entry door**Revision: 10-1-2015 Revised product per client request**Revision: 7-8-2015 Location clarification, carpet is only in bedroom and closets Contact InformationRecommended Vendor: Mohawk Properties CollectionAddress:

Contact: Ty ThompsonPhone: 512-203-4833Email: ty_thompson@mohawkind.com

Project Information

FLOOR: CARPET U-C-1

**Flooring transition strips between dissimular floor finish materials must not to exceed max. 1/4"V, if transition strip exceeds 1/4"V, it must not exceed 1/2"V with top 1/4" having a 1:2 or shallower bevel. If exceeding max 1/2" V it must then have a 1:12 or shallower slope

[ UNIT ]

Location: All 1st Level Units throughout exceptBedrooms, Bathrooms, and ClosetsAll Upper Level Units Kitchens

Description: Vinyl Plank Manufacturer: FloorFolioCollection: TimberColor / Number: 636-673Size: 6" x 36"Overall Thickness: 2mm (.080")Wear Layer: 8milInstallation: Direct Glue

Notes:**Refer to Architectural Unit Sheets for location.**All 1st Level Unit Living Rooms and Dining Areas will receive vinyl plank flooring.

**Revision: 10-1-2015 Location clarification, vinyl plank is used throughout except the above noted roomsContact InformationRecommended Vendor: FloorFolio IndustriesAddress: 110 Mayfield Ave

Edison, New Jersey 08837

Contact: Mike CarterPhone: 817-504-4996Email: mcarter@floorfolio.com

Project Information

FLOOR: VINYL PLANK U-VP-1

**Flooring transition strips between dissimilar floor finish materials must not to exceed max. 1/4"V, if transition strip exceeds 1/4"V, it must not exceed 1/2"V with top 1/4" having a 1:2 or shallower bevel. If exceeding max 1/2" V it must then have a 1:12 or shallower slope

[ UNIT ]

Location: All Unit Bathrooms

Description: Porcelain Floor TileManufacturer: InterceramicsCollection: ContessaColor / Number: PewterSize: 12" x 24"Thickness: 11mm (7/16")Installation: Brick Lay (1/3 offset)Grout Color: Custom Building Products

#545 Bleached Wood

Notes:**Refer to Architectural Unit Sheets for location.

Contact InformationRecommended Vendor: InterceramicAddress: 9701 Metric Blvd., #100

Austin, TX 78758Website: www.interceramicusa.com

Contact: Esther RollinsPhone: 512-497-9459Email: erollins@Interceramic.com

Project Information

FLOOR: FLOOR TILE U-FT-1

[ UNIT ]

Location: Vinyl Plank to Floor Tile

Description: Metal Transition StripManufacturer: SchluterStyle: RENO-UStyle#: EBU110Size: 7/16" (11mm)Finish: Brushed stainless steel (EB)Installation: Refer to Manufacturer Instructions

Notes:**Flooring installer to verify Schluter Transition Strip model number per flooring material height.

Project Information

FLOOR: TRANSITION U-TR-1

[ UNIT ]

Location: Carpet to Floor Tile

Description: Metal Transition StripManufacturer: SchluterStyle: RENO-TKStyle#: EBTK110Size: 7/16" (11mm)Finish: Brushed stainless steel (EB)Installation: Refer to Manufacturer Instructions

Notes:**Flooring installer to verify Schluter Transition Strip model number per flooring material height.

Project Information

FLOOR: TRANSITION U-TR-2

[ UNIT ]

Project Information

UNITBASE & TRIM FINISHES

[ UNIT ]

Location: All Units throughout

Description: Painted Wood BaseManufacturer: Architectural MillworkProfile: Square Edge Size: 4"HSpecies: FJ PinePaint: U-PT-2, Semi-gloss finish

Notes:**Contractor may provide "or equal" profile for Interior Designer's approval.

Contact InformationRecommended Vendor: Ameritech MillworksAddress: 2300 West Marshall Drive

Grand Prairie, Texas 75051Website: www.amillworks.com

Contact: John GilliamPhone: 817-825-1866 cellEmail: JGilliam@amillworks.com

Project Information

BASE U-B-1

[ UNIT ]

Description: Door CasingManufacturer: Architectural MillworkProfile: Square Edge Size: 1" x 4"Species: FJ PinePaint: U-PT-2, Semi-gloss finish

Notes:**Contractor may provide "or equal" profile for Interior Designer's approval.

**Revision: 10-1-2015 Revised size informationContact InformationRecommended Vendor: Ameritech MillworksAddress: 2300 West Marshall Drive

Grand Prairie, Texas 75051Website: www.amillworks.com

Contact: John GilliamPhone: 817-825-1866 cellEmail: JGilliam@amillworks.com

Project Information

TRIM: DOOR CASING U-TM-1

[ UNIT ]

Location: All Unit Bathrooms throughout(Finishing trim for exposed edgesof tub and shower wall tile)

Description: Tile Edge ProtectionManufacturer: SchluterProfile: JOLLY Style: A100ATSize: 3/8" - 10mmFinish: AT Satin Nickel

Anodize Aluminum

Notes:**Contractor may provide "or equal" profile for Interior Designer's approval.**To be installed at exposed vertical edges only.

**Revision 10-1-2015 Updated installation notes per client requestContact InformationRecommended Vendor: InterceramicAddress: 9701 Metric Blvd., #100

Project Information

TRIM - TILE EDGE PROTECTION U-TM-2

[ UNIT ]

Project Information

UNITPAINT & WALL FINISHES

[ UNIT ]

Location: All Unit walls and ceiling paint throughout

Description: Unit Wall and Ceiling PaintManufacturer: Sherwin WilliamsColor: Worldly Gray Number: SW7043Finish Flat Finish (Unit walls and

and ceiling u.n.o.)Semigloss Finish (BathroomWalls and Ceiling)

Wall Texture: Medium Orange Peel

Notes:**Low VOC paints to be used.**Minimum of Two Coats of Paint to cover.**Contractor to provide 2' x 2' mock ups in field for approval prior to ordering paint.

**Revision: 10-1-2015 Revised wall texture per client requestContact InformationRecommended Vendor: Sherwin WilliamsAddress:

Contact: Sherwin WilliamsPhone: 800-4-SHERWINWebsite: www.sherwin-williams.com

Project Information

PAINT U-PT-1

[ UNIT ]

Location: All Unit Base, Door Casing,and Interior Doors

Description: Trim PaintManufacturer: Sherwin WilliamsColor: Reserved WhiteNumber: SW7056Finish: Semi Gloss

Notes:**Low VOC paints to be used.**Minimum of Two Coats of Paint to cover.**Contractor to provide 2' x 2' mock ups in field for approval prior to ordering paint.

Contact InformationRecommended Vendor: Sherwin WilliamsAddress:

Contact: Sherwin WilliamsPhone: 800-4SHERWINWebsite: www.sherwinwilliams.com

Project Information

PAINT U-PT-2

[ UNIT ]

Location: Unit Bathrooms(tub/shower surround)

Description: Ceramic Wall TileManufacturer: InterceramicsStyle/Number: AquarelleColor: Shadow GraySize: 10" x 20"Thickness: 8.15mm Installation: Straight LayGrout Color: Custom Building Products

#545 Bleached Wood

Notes:**Refer to Interior Design Unit Elevations for wall tile locations & installation pattern.**Grout joint to be 1/8" maximum.**Seal all grout joints.**Schluter trim U-TM-2 to be installed at exposed vertical edges only

**Revision: 10-1-2015 Updated installation notes per client requestContact InformationRecommended Vendor: InterceramicAddress: 9701 Metric Blvd., #100

Project Information

WALL TILE U-WT-1

[ UNIT ]

Location: Unit Kitchen(Full height Backsplash)

Description: Ceramic Wall TileManufacturer: InterceramicsStyle/Number: Marbre Color: IvoryFinish: Natural (matte)Size: 4.25"x12.75"Thickness: 1/4"Installation: Brick Lay (1/3 offset)Grout Color: Custom Building Products

#381 Bright White

Notes:**Grout joint to be 1/8" maximum.**Seal all grout joints.

**Revision: 10-1-2015 Revised installation informationContact InformationRecommended Vendor: InterceramicAddress: 9701 Metric Blvd., #100

Project Information

WALL TILE U-WT-2

[ UNIT ]

Project Information

UNITMILLWORK FINISHES

[ UNIT ]

Location: All Unit Kitchen and Bathrooms

Description: Manufactured CabinetryProvided By: Master WoodcraftStyle: Roma

Framed-Full overlayFinish: EspressoAdditional Info: 7 total ANSI accessible and

live/work units: (4) A4 and (3) B2. Refer to Architectural Sheets for locations.

Notes:**42"H upper cabinets to be installed at kitchens**36"H upper cabinet to be installed over toilets at specific units. Refer to Architectural set for InteriorElevations**ANSI Accessible and live/work units to receive ADA Compliant cabinet heights and removable basecabinets at sinks.**(7) ANSI Accessible and live/work units to receive floor finish that continues under removable base cabinets

**Revision: 10-1-2015 Revised door style and added information per client requestContact InformationRecommended Vendor: Master WoodcraftAddress: 232 North Marshall Industrial Avenue

Marshall, TX 75670

Contact: Kelly AdamsPhone: 903-930-5193Website: www.mwccabinetry.com

Project Information

CABINETRY U-CAB-1

[ UNIT ]

Location: All Unit Kitchens and Bathrooms

Description: Quartz SurfaceManufacturer: Golden StonesColor: Pure GreyThickness: 2cmEdge Profile: Eased

Notes:**4" Quartz backsplash at Bathrooms.

**Revision: 10-1-2015 ClarificationContact InformationRecommended Vendor: Golden Stones LPAddress: 7902 Hillmont St.

Houston, Tx. 77040Website: www.goldenstones.com

Contact: Randy SkinnerPhone: 713-934-7887 - Office

713-934-7889 - Fax832-250-4227 - Cell

Email: RandySkinner@goldenstones.com

Project Information

COUNTERTOP U-S-1

[ UNIT ]

Location: All Unit Kitchens and Bathrooms

Description: Quartz SurfaceManufacturer: SilestoneColor: Grey ExpoThickness: 2cmEdge Profile: Eased

Notes:**4" Quartz backsplash at Bathrooms.

**Revision: 10-1-2015 ClarificationContact InformationRecommended Vendor: The Kip Co.Address: 7155 Old Katy Road, Suite S104

Houston, TX 77024Website www.thekipco.com

Contact: Kip AltstaetterPhone: (713) 590-0660Email: kip@thekipco.com

Project Information

COUNTERTOP - ALTERNATE U-S-1 ALT.

[ UNIT ]

Project Information

UNIT LIGHTING

[ UNIT ]

Location: Unit BathroomsSee Notes

Description: Deco BN LED VanityManufacturer: Biltmore Lighting (Custom)Style/Number: BLED1841Size: 25.5"W x 4.75"H x 4.25"DFinish: Satin NickelLamp: 2 x 10.5w 3000k LED (array included)Shade: Matte White Acrylic

Installation: Back plate to be 4" above mirror

Notes:**At single sink vanities, install 1 light fixture, centered on framed mirror, mounted 4" above mirror.**At double sink vanities, install 2 light fixtures, centered above each sink, mounted 4" above framed mirror.**Unit lighting package to be submitted to Interior Designer for final approval.

**Revision: 10-1-2015 Revised per VE alternates submited. Contact InformationRecommended Vendor: Biltmore LightingAddress:

Website:

Contact: Provided by Lighting Sub Contractor Phone:Email:

Project Information

LIGHTING U-DF-1

[ UNIT ]

Location: Kitchen Bar Pendant

Description: PendantManufacturer: Biltmore Lighting (Custom)Style/Number: B4312-CHRSize: 14.55"H x 7.2"Dia.Finish: White ChromeLamp: (1) 8W LED

Notes:**Refer to MEP plans for quantities and locations.**Unit lighting package to be submitted to Interior Designer for final approval.

**Revision: 10-1-2015 Revised per VE alternates submited. Contact InformationRecommended Vendor: Biltmore Lighting

Contact: Provided by Lighting Sub Contractor Phone:Website:

Project Information

LIGHTING U-DF-2

[ UNIT ]

Location: Entry, Hallway, Kitchen, Dining Areas,Bathrooms

Description: Disk LightManufacturer: Classic Lighting by J&LStyle/Number: 120V 6" LED Disk Light

SM6-15W-30K-W-D-WHTDimensions: 7.4"D x 1.6"H for 6" can lightFinish: WhiteLamp: (36) 15w LED chipsColor Temp: 3000K

Notes:**Refer to MEP plans for specific units, and quantities.**Lighting Sub Contractor to submit equal alternate options for GC pricing.**Unit lighting package to be submitted to Interior Designer for final approval.

**Revision: 10-1-2015 Revised per VE alternates submited. Contact InformationRecommended Vendor: J & L Industries Inc.

707 Avenue E.Stafford, TX 77477

Contact: Customer ServicePhone: 281-403-6733Website: www.jldistributors.com

Project Information

LIGHTING U-DF-3

[ UNIT ]

Location: Unit Exterior Patio Storage

Description: Mushroom Ceiling MountManufacturer: Biltmore Lighting (Custom)Style/Number: 2 Light Opal Mushroom, Energy Saving

B36GU213-XX-27KSize: 11.5" Dia. X 5.5"HFinish: Nickel/Opal WhiteLamp: (2)13W, GU24 CFL, 2700K

Notes:**Refer to MEP plans for quantities and locations.**Lighting Sub Contractor to submit equal alternate options for GC pricing.**Unit lighting package to be submitted to Interior Designer for final approval.

Contact: Provided by Lighting Sub ContractorPhone:Website:

Project Information

LIGHTING U-DF-4

[ UNIT ]

Location: Unit Utility and Closets

Description: Mushroom Ceiling MountManufacturer: Biltmore Lighting (Custom)Style/Number: 2 Light Opal Mushroom, Energy Saving

B36GU213-XX-27KSize: 11.5" Dia. X 5.5"HFinish: Nickel/Opal WhiteLamp: (2)13W, GU24 CFL, 2700K

Notes:**Refer to MEP plans for quantities and locations.**Lighting Sub Contractor to submit equal alternate options for GC pricing.**Unit lighting package to be submitted to Interior Designer for final approval.

Project Information

LIGHTING U-DF-5

[ UNIT ]

Location: Unit Bedrooms and Living

Description: Ceiling Fan with LightManufacturer: Biltmore Lighting (Custom)Style/Number: C785 BN/WLNTSize: 52"W sweepBlade Finish: Walnut Fan Finish: Brushed NickelGlass: OpalSize: 52"Lamp: (2) 13 W., GU24

Project Information

LIGHTING U-DF-6

[ UNIT ]

Location: Unit Balcony

Description: Outdoor Wall Mount, Steel Pan and Aluminum Frame

Manufacturer: Divine LightingStyle/Number: Sundance SUN712Size: 7"W x 12"H x 4"DFinish: Bronze, MT-Metal TopLamp: IncludedLens: WP-White PolycarbonateBallast: 120 v class P, 60 Hz. Magnetic

120 v class P, 60 Hz. Magnetic

**Revision: 10-1-2015 Revised fixture finishContact InformationRecommended Vendor: Divine LightingAddress: 3704 Hilltop, Ste. 200

Conroe, Texas 77303

Contact: Customer ServicePhone: 936-494-3900Website: www.divinelighting.net

Project Information

LIGHTING U-DF-7

FINISH TO BE BRONZE

[ UNIT ]

Project Information

UNITPLUMBING FIXTURES

[ UNIT ]

Location: Unit Kitchen

Description: Pull Down Kitchen FaucetManufacturer: PfisterStyle Name: LitaModel Number: GT529-SMSSize: 17"H x 9"P (OC)Finish: Stainless SteelFeatures: ADA Compliant, 1.8gpm

Notes:**Contractor to submit equal alternates for Interior Designer's approval.**ADA Compliant.

Contact InformationRecommended Vendor: Pfister FaucetsAddress: 19701 DaVinci

Lake Forest, California 92610

Contact: Customer ServicePhone: 1-800-732-8238Website: www.pfisterfaucets.com

Project Information

SINK FAUCET U-PF-1

[ UNIT ]

Location: Unit Bathroom Faucet

Description: Single Control Centerset Faucet Manufacturer: PfisterStyle Name: SeliaModel Number: F-042-SLKKSize: 7-3/8"H Finish: Brushed NickelMounting: One Hole InstallationFeatures: ADA Compliant, 1.5gpm

Notes:**Contractor to submit equal alternates for Interior Designer's approval.**Contractor to ensure proper clearance for faucet lever before ordering.

**Revision: 10-1-2015 Revised fixture style per client requestContact InformationRecommended Vendor: Pfister FaucetsAddress: 19701 DaVinci

Lake Forest, California 92610

Contact: Customer ServicePhone: 1-800-732-8238Website: www.pfisterfaucets.com

Project Information

SINK FAUCET U-PF-2

[ UNIT ]

Location: Unit Bathrooms

Description: Single Control tub/shower TrimManufacturer: CFG by MoenStyle Name: CornerstoneModel Number: 4311CBNGRFinish: Brushed NickelFeatures: ADA Compliant, 1.75 gpm

Notes:**Contractor to submit equal alternates for Interior Designer's approval.**Contractor to submit plumbing submittal package to Interior Designer prior to ordering fixtures.

**Revision: 10-1-2015 Revised per Client requestContact InformationRecommended Vendor: CFG by MoenAddress:

Contact: Customer ServicePhone: 888-450-5522Website: www.cfgonline.com

Project Information

TUB/SHOWER U-PF-3

[ UNIT ]

Description: Single Control Showerhead andFlange

Manufacturer: CFG by MoenStyle Name: CornerstoneModel Number: 40315CBNGRFinish: Brushed NickelFeatures: ADA Compliant, 1.75 gpm

Notes:**Contractor to submit equal alternates for Interior Designer's approval.**Contractor to submit plumbing submittal package to Interior Designer prior to ordering fixtures.

**Revision: 10-1-2015 Revised per Client requestContact InformationRecommended Vendor: CFG by MoenAddress:

Contact: Customer ServicePhone: 888-450-5522Website: www.cfgonline.com

Project Information

SHOWER ONLY U-PF-4

[ UNIT ]

Location: ADA UnitBathrooms (Shower only)

Description: 3 Function Hand Shower with Bracket

Manufacturer: ProFloStyle: PF14310CPFinish: Polished ChromeFeatures: 1.75 gpm

Notes:**Contractor to submit equal alternates for Interior Designer's approval.**To be installed in ADA units.

Contact InformationRecommended Vendor: ProFloAddress: 10500 Metropolitan Dr

Austin, TX 78758

Contact: Customer ServicePhone: 512-837-2290Website: www.proflo.com

Project Information

SHOWER - ADA U-PF-5a

[ UNIT ]

Location: ADA UnitBathrooms (Shower only)

Description: 24 Slide Bar with 7/8 Brass BarManufacturer: ProFloStyle: PF14BSBNFinish: Brushed Nickel

Notes:**Contractor to submit equal alternates for Interior Designer's approval.**To be installed in ADA units.

Contact InformationRecommended Vendor: ProFloAddress: 10500 Metropolotan Dr

Austin, Tx 78758

Contact: Customer Service Phone: 512-837-2290Website: www.proflo.com

Project Information

SHOWER SLIDE BAR - ADA U-PF-5b

**Brushed Nickel Finish

[ UNIT ]

Location: Unit Kitchen

Description: Stainless Steel Undermount Single Basin

Manufacturer: Just ManufacturingStyle: US-1830-ADimensions: 30"L x 18"WBowl Depth: 8"Finish: Stainless SteelGauge: 18Drain Punch: J-35 drain

Notes:

Contact InformationRecommended Vendor: Just ManufacturingAddress: 9233 King St

Franklin Park, IL 60131

Contact: Customer ServicePhone: 847-678-5151Website: www.justmfg.com

Project Information

SINK U-PF-6a

[ UNIT ]

Location: ADA Unit Kitchen

Description: Stainless Steel Undermount Single Basin

Manufacturer: Just ManufacturingStyle: US-ADA-1830-ADimensions: 30"L x 18"WBowl Depth: 5 1/2"Finish: Stainless SteelGauge: 18

Notes:**Plumbing contractor to submit equal alternates.**Sink to be installed 2" from front edge of counter per ADA requirements.**There are 7 total ANSI accessible units: (4) A4 and (3) B2. Refer to architectural sheets for locations.

**Revision: 10-1-2015 Added informationContact InformationRecommended Vendor: Just ManufacturingAddress: 9233 King St

Franklin Park, IL 60131

Contact: Customer ServicePhone: 847-678-5151Website: www.justmfg.com

Project Information

SINK - ADA U-PF-6b

[ UNIT ]

Description: Undermount SinkManufacturer: American StandardStyle: Studio Undercounter SinkStyle Number: 0614000.020/ 033056565506Dimensions: 21-1/4"L x 15-1/4"W x 6-3/4"DFinish: White 20

Notes:**Plumbing contractor to submit equal alternates.

Contact InformationRecommended Vendor: American StandardAddress:Website: www.americanstandard-us.com

Contact: Customer ServicePhone: 1-800-442-1902Email:

Project Information

SINK U-PF-7a

[ UNIT ]

Location: ADA Unit Bathrooms

Description: Undermount SinkManufacturer: KohlerStyle: LadenaStyle Number: K-2214Dimensions: 20-7/8"L x 14-3/8"W x 8-1/8"DFinish: White 0

Notes:**Plumbing contractor to submit equal alternates.**Sink to be installed per manufacturer's installation directions to meet ADA requirements.**There are 7 total ANSI accessible units: (4) A4 and (3) B2. Refer to architectural sheets for locations.

**Revision: 10-1-2015 Added informationContact InformationRecommended Vendor: KohlerAddress:Website: www.kohler.com

Contact: Customer ServicePhone: 1-800-4KOHLEREmail:

Project Information

SINK - ADA U-PF-7b

[ UNIT ]

Location: All A1 Units

Description: BathtubManufacturer: Spurlin IndustriesStyle: F 6030 GT L/RFinish: WhiteSize: 60"L x 30"W x 19"H

Notes:**Contractor to submit equal alternates for Interior Designer's approval.**Contractor to determine left or right drain location based on Architectural drawings.

**Revision: 10-1-2015 Tub specification determinedContact InformationRecommended Vendor: Ferguson Enterprises, IncAddress: 2551 N. Mays

Round Rock, TX 78665

Contact: Scott SupakPhone: 512-751-1580Email: scott.supak@ferguson.com

Project Information

BATH TUB U-PF-8a

[ UNIT ]

Location: All Units Except A1

Description: BathtubManufacturer: Spurlin IndustriesStyle: F 6036 GT L/RFinish: WhiteSize: 60"L x 35"W x 21 1/2"H

Notes:**Contractor to submit equal alternates for Interior Designer's approval.**Contractor to determine left or right drain location based on Architectural drawings.

**Revision: 10-1-2015 Tub specification determinedContact InformationRecommended Vendor: Ferguson Enterprises, IncAddress: 2551 N. Mays

Round Rock, TX 78665

Contact: Scott SupakPhone: 512-751-1580Email: scott.supak@ferguson.com

Project Information

BATH TUB U-PF-8b

[ UNIT ]

Description: Elongated ToiletManufacturer: GerberStyle Name: Maxwell HET Elongated ToiletStyle Number: 21-912GPF: 1.28Finish: White

Notes:**Contractor to submit equal alternates for Interior Designer's approval.

Contact InformationRecommended Vendor: GerberAddress:

Contact: Customer ServicePhone: 866-538-5536Website: www.gerberonline.com

Project Information

TOILET U-PF-9a

[ UNIT ]

Location: ADA Unit Bathrooms

Description: Elongated ToiletManufacturer: GerberStyle Name: Maxwell HET Elongated ToiletStyle: 21-918GPF: 1.28Finish: White

Notes:**Contractor to submit equal alternates for Interior Designer's approval.**To be installed in ADA units.**There are 7 total ANSI accessible units: (4) A4 and (3) B2. Refer to architectural sheets for locations.

**Revision: 10-1-2015 Added informationContact InformationRecommended Vendor: GerberAddress:

Contact: Customer ServicePhone: 866-538-5536Website: www.gerberonline.com

Project Information

TOILET - ADA U-PF-9b

[ UNIT ]

Location: 2 Bedroom Units

Description: Molded Fiberglass Shower Receptorw/ The Edge

Manufacturer: TBDStyle: TBDFinish: WhiteSize: 38"W x 60"L

42"W x 60"L At B4 units

Contact InformationRecommended Vendor: TBDAddress:

Contact:Phone:Website:

Project Information

SHOWER PAN U-PF-10

[ UNIT ]

Project Information

UNITBATH ACCESSORIES

[ UNIT ]

Description: 24" Towel BarManufacturer: TaymorStyle: LUX 1300 SeriesModel Number: 04-1324Finish: Polished Chrome

**Revision: 10-1-2015 Revised per client requestContact InformationRecommended Vendor: TaymorAddress: 1655 Derwent Way

Annacis Island, Delta, BC V3M6K8

Contact: Customer ServicePhone: 604-540-9525Website: www.taymor.ca

Project Information

BATH ACCESSORY U-BA-1

[ UNIT ]

Description: 18" Towel BarManufacturer: TaymorStyle: LUX 1300 SeriesModel Number: 04-1318Finish: Polished Chrome

Project Information

[ UNIT ]

Description: Tissue HolderManufacturer: TaymorStyle: LUX 1300 SeriesModel Number: 04-1348Finish: Polished Chrome

**Revision:10-1-2015 Revised per client requestContact InformationRecommended Vendor: TaymorAddress: 1655 Derwent Way

Project Information

[ UNIT ]

Description: Towel RingManufacturer: TaymorStyle: LUX 1300 SeriesModel Number: 04-1304Finish: Polished Chrome

Project Information

BATH ACCESSORY U-BA-4a

[ UNIT ]

Description: Double Robe HookManufacturer: TaymorStyle: LUX 1300 SeriesModel Number: 04-1302Finish: Polished Chrome

**Revision:10-1-2015 Addition per client requestContact InformationRecommended Vendor: TaymorAddress: 1655 Derwent Way

Project Information

BATH ACCESSORY U-BA-4b

[ UNIT ]

Description: Curved Shower RodManufacturer: Pamex Inc.Style: Crescent Curved 5ft RodModel Number: BSR-552Size 5' L x 1"D

Finish: Satin Nickel

Notes:**Shower rod to be mounted at 6'-8" AFF

**Revision: 10-1-2015 Mounting height added to specification per client requestContact InformationRecommended Vendor: Pamex Inc.Address:

Contact: Customer ServicePhone: (800) 621-6869Website: www.pamexinc.com

Project Information

[ UNIT ]

Manufacturer: InterceramicsDescription: Medium Corner CaddyStyle: White Ceramic Bathroom ShelfFinish: CeramicSize: 8-1/4" x 8-1/4"Color: White

Notes:**Contractor to submit equal alternates for Interior Designer's approval.**Mounting height to be 3'-6"(+/-) so that bottom aligns with grout joint at showers.**Refer to typical tub and shower tile pattern installation on next page.

**Revision: 10-1-2015 Mounting height added to specification page. Contact InformationRecommended Vendor: Interceramic USAAddress: 9701 Metric Blvd., #100

Contact: Esther RollinsPhone: 512-497-9459Email: erollins@interceramic.com

Project Information

[ UNIT ]

Project Information

UNITDOOR STYLE & HARDWARE

[ UNIT ]

Location: All Unit Interior Doors

Description: Interior 5 Panel DoorManufacturer: Provided by sub contractorSeries: 5 PanelHeight: 6'-8" And 8'-0" (See Notes)Type: MouldedFinish: SmoothPaint Color: U-PT-2

Notes:**Confirm door height and thickness with Architectural Door Schedule.**Confirm all Fire Rating requirements with Architect.** 1st level units to receive 8'-0"H interior doors.**2nd, 3rd, 4th level units to receive 6'-8"H interior doors. **5th level units #501, #512, #537, #566 to receive 8'-0"H interior doors. All remaining 5th level units to receive6'-8"H interior doors.

**Revision: 10-1-2015 Revised door height and specification Contact InformationRecommended Vendor: Ameritech MillworksAddress: 2300 West Marshall Drive

Grand Prairie, TX 75051

Contact: John GilliamPhone: 817-640-8133Website: www.amillworks.com

Project Information

DOOR U-D-1

[ UNIT ]

Location: All Unit Entry Doors

Description: Exterior 5 Panel DoorManufacturer: Provided by Sub ContractorStyle: 5 Panel Equal, No GlassHeight: 8'-0"Type: MetalFinish: SmoothPaint Color: Sherwin Williams

Urban Bronze SW7048

Notes:**Confirm door height and thickness with Architectural Door Schedule.**Confirm all Fire Rating requirements with Architect.

**Revision: 10-1-2015 Revised specification per client request.Contact InformationRecommended Vendor: Ameritech MillworksAddress: 2300 West Marshall Drive

Project Information

DOOR U-D-2

[ UNIT ]

Location: All Unit Patio Doors

Description: Exterior Single LiteManufacturer: Provided by Sub ContractorStyle: Full Lite Steel DoorHeight: 8'-0"Type: MetalFinish: SmoothPaint Color: TBD

Notes:**Confirm door height and thickness with Architectural Door Schedule.**Confirm all Fire Rating requirements with Architect.**Confirm which units have transome windows above door.

**Revision: 10-1-2015 Revised per client request.Contact InformationRecommended Vendor: Ameritech MillworksAddress: 2300 West Marshall Drive

Project Information

DOOR U-D-3

[ UNIT ]

Location: Unit Privacy Doors:Bedrooms & Bathrooms

Description: Privacy Door LeverManufacturer: Better Home ProductsStyle: Soma LeverFinish: Satin Nickel

Notes:**Contractor to verify all locking information with Owner.

**Revision: 10-1-2015 Revised per client request. Contact InformationRecommended Vendor: Better Home ProductsAddress:

Contact: Customer ServicePhone: 650-827-9270Website: www.betterhomeproducts.com

Project Information

HARDWARE U-H-1

[ UNIT ]

Location: Unit Passage Doors:Entry, Closets & Utility

Description: Passage Door LeverManufacturer: Better Home ProductsStyle: Soma LeverFinish: Satin Nickel

Notes:**Entry Door to receive Client approved deadbolt provided by Contractor.

**Revision: 10-1-2015 Revised per client request. Contact InformationRecommended Vendor: Better Home ProductsAddress:

Contact: Customer ServicePhone: 650-827-9270Website: www.betterhomeproducts.com

Project Information

HARDWARE U-H-2

[ UNIT ]

Location: Unit Kitchen & Bathrooms

Description: Cabinet PullManufacturer: DeltanaStyle: Bar PullModel Number: BP3000SSFinish: Stainless SteelDimensions: 5.25" Overall Length

3" C to C

Notes:**Contractor may provide "or equal" for Interior Designer's approval.

Contact InformationRecommended Vendor: DeltanaAddress:

Contact: Customer ServicePhone: 1-800-665-2226Website: www.deltana.net

Project Information

HARDWARE U-H-3

[ UNIT ]

Project Information

UNITMISCELLANEOUS

[ UNIT ]

Description: Switchplates and Outlet CoversManufacturer: Cooper Wiring DevicesStyle: 2132WFinish: White

Notes:

Contact InformationRecommended Vendor: Cooper Wiring DevicesAddress:

Contact: Customer ServicePhone: 866-853-4293Website: www.cooperindustries.com

Project Information

MISCELLANEOUS U-M-1

[ UNIT ]

Description: Switchplates Manufacturer: Cooper Wiring DevicesStyle: Rocker SwitchesFinish: White

Notes:

Contact InformationRecommended Vendor: Cooper Wiring DevicesAddress:

Contact: Customer ServicePhone: 866-853-4293Website: www.cooperindustries.com

Project Information

MISCELLANEOUS U-M-2

[ UNIT ]

Description: Wall TextureManufacturer: ContractorStyle: Medium Orange Peel

Notes:

**Revision: 10-1-2015 Revised wall texture per client requestContact InformationRecommended Vendor: General ContractorAddress:

Contact:Phone:Email:

Project Information

MISCELLANEOUS U-M-3

[ UNIT ]

Location: Window Blinds Throughout

Description: Faux wood collectionManufacturer: GraberStyle: 2" Faux Wood Traditions

#2539 Finish: Artic White

Notes:**Contractor to submit "or equal" options to Interior Designer for approval.

Contact InformationRecommended Vendor: GraberAddress:

Contact: Customer ServicePhone: 877-792-0002Website: www.graberblinds.com

Project Information

MISCELLANEOUS U-M-4

[ UNIT ]

Location: Unit Bathrooms Throughout

Description: Framed MirrorsManufacturer: FramericaStyle: BW241-061Finish: Espresso WalnutSize: 2"W x 3/4"H x 1/2"Rabbet

Notes:**At 1st level units, wood frame to sit directly on vanity backsplash per ADA.**At upper level units, wood frame to be mounted 1.5" above vanity backsplash. **Typical Install: Frame to be mounted 1.5" above vanity backsplash**ANSI and Live/Work Install: Frame to be mounted so that it sits directly on top of vanity backsplash**There are 7 total ANSI accessible units: (4) A4 and (3) B2. Refer to architectural sheets for locations.**Revision: 10-1-2015 Revised with notes addedContact InformationRecommended Vendor: FramericaAddress: 2 Todd Court

Yaphank, NY 11980

Contact: Customer ServicePhone: 800-372-6422Website: www.framerica.com

Project Information

MISCELLANEOUS U-M-5

lenox boardwalk erollins@interceramic.com project information lenox boardwalk development 1500 south...

Documents

lenox cutting tools

lenox advisors

kemah boardwalk

lenox banner 36x84

lenox pwm brochure

mep engineer filemep engineer: joe e. hutchison, pe . lenox...

boardwalk - assets.moen.com

lenox study day

lenox center

lenox corporate benefits

paquete lenox

laparoscopía - american lenox

lenox overview

boardwalk design - wilson timbers · 2018. 10. 30. ·...

jjp lenox catalog

presentación1 lenox

northwell health, inc. and lenox hill hospital corporate...

manual control lenox

lenox welcome brochure

club specs title page- elmont - oden hughes, llcemail:...