bc-2002 tandem rev3
TRANSCRIPT
Copyright 2004 BearCat Mfg., Inc. Revised January 31, 2004
FIELD OPERATIONS & MAINTENANCE 2000/2004
MODEL BC-2002/CRC TANDEM
Unit Serial Number:
Date of Service:
Customer:
Hopper ID Number (front):
Hopper ID Number (rear):
Footage Calibration Number:
BearCat Mfg., Inc. 3650 Sabin Brown Road Wickenburg, AZ 85390 Phone: (928) 684-7851 Fax: (928) 684-3241
T-2
This manual describes the Model BC-2002/CRC Tandem Chip Spreader as it is normally delivered to the user. Due to a continuing program of product improvement, changes may be made in equipment delivered at a later date. Every attempt is made to keep users fully informed of such changes.
BearCat Mfg. Date Received ___________________
REPORT OF POSSIBLE DATA ERROR
Mail this form to the address on the title page or FAX to (928) 684-3241
Your Name Company
Address
State Country Zip
Telephone No. FAX Date
Manual Title Page No. Paragraph Figure No. Table No. Problem
BearCat Reply:
Approval:
FOLD FOLD --------------------------------------------------------------------------------------------------------------------- From:
Place Stamp Here
BearCat Mfg. 3650 Sabin Brown Road Wickenburg, AZ 85390 --------------------------------------------------------------------------------------------------------------------- FOLD FOLD
Model BC-2002/CRC Tandem
March 31, 2002 WAR-1
WARRANTY AND CLAIM PROCEDURES
LIMITED WARRANTY
BearCat Mfg., Inc. (hereinafter referred to as “BearCat”) extends to the original purchaser-user of Model BC-2002/CRC Tandem Chip Spreader, the following warranty covering goods manufactured by BearCat and subject to the following qualifications.
The warranty applies only when the product:
1. Is properly used and maintained in accordance with BearCat instructions, governing agencies or associations.
2. Is being operated under proper fuel and/or cargo specifications.
3. Is not subjected to corrosive or abrasive atmosphere or materials.
4. Has not been damaged through malice or ignorance.
5. Has not been subjected to flood, lightning, accidents, misuse, neglect or unauthorized modification, repair or service.
Parts replaced under this warranty are warranted only through the remaining time of the original warranty.
BearCat warrants that at the time of delivery, the product manufactured by BearCat and delivered new to the original purchaser-user shall be free from defects in material and workmanship for a period of one (1) year after delivery. This warranty is valid when the product is operated and maintained under normal use and service and in accordance with the written instructions provided by BearCat.
Warranty Claims
BearCat agrees at its option, to repair or replace F.O.B. Wickenburg, Arizona, any part acknowledged by BearCat to be defective, provided:
1. The user notifies BearCat of any defect within this warranty no later than thirty (30) days after a defect is discovered.
2. Written or verbal authorization has been obtained from the BearCat Service Department to return the product.
Model BC-2002/CRC Tandem
WAR-2 March 31, 2002
3. Upon authorization, the defective part is returned within 60 days for inspection with transportation charges prepaid to BearCat.
BearCat Mfg., Inc. 3650 Sabin Brown Road Phone: (928) 684-7851 Wickenburg, AZ 85390 Fax: (928) 684-3241
4. BearCat determines the defective part failed under the terms of the above warranty.
BEARCAT WILL NOT INSTALL AND WILL NOT PAY ANY INSTALLATION COST, TRANSPORTATION COST, TRAVEL TIME, MILEAGE, LABOR COSTS OR OTHER EXPENSES OF ANY DEFECTIVE PARTS REPLACED OR REPAIRED UNLESS THE USER HAS REACHED A PRIOR AGREEMENT WITH BEARCAT.
EXCLUSIONS
The provisions of the foregoing warranty are BearCat’s sole obligation and exclude all other warranties, expressed or implied.
BearCat shall not be responsible for any loss, damage, incidental or consequential damages of any kind, whether based upon warranty, contract or negligence, arising concerning the sale, use, or repair of the product.
Components manufactured by any supplier other than BearCat shall bare only the warranty made by the manufacturer of that product.
3650 Sabin Brown RoadWickenburg, Arizona 85390
928-684-7851
BearCat Mfg.TM
Model BC-2002/CRC Tandem List of Effective Pages
LIST OF EFFECTIVE PAGES
Revision 0 March 31, 2002 Revision 1 July 15, 2002 Revision 2 January 31, 2004
Subheading and Page Rev Subheading and Page Rev
January 31, 2004 LEP-1
TITLE PAGE T-1 2 T-2 2
WARRANTY/CLAIM PROCEDURES
WAR-1 0 WAR-2 0
LIST OF EFFECTIVE PAGES LEP-1 2 LEP-2 2 LEP-3 2 LEP-4 2
TABLE OF CONTENTS TC-1 1 TC-2 1
LIST OF FIGURES TC-3 0 TC-4 0 TC-5 0
LIST OF TABLES TC-6 0
INTRODUCTION INTRO-1 0 INTRO-2 0
SECTION 1. DESCRIPTION 1-1 0 1-2 0 1-3 0 1-4 0 1-5 0 1-6 0 1-7 0 1-8 2 1-9 2 1-10 2
SECTION 2. SAFETY PRECAUTIONS 2-1 0 2-2 0
SECTION 3. PREPARING EQUIPMENT FOR USE
3-1 0 3-2 0 3-3 0 3-4 0 3-5 0 3-6 0 3-7 0 3-8 0 3-9 0 3-10 0 3-11 0 3-12 0 3-13 0 3-14 0 3-15 0 3-16 0
SECTION 4. OPERATING INSTRUCTIONS 4-1 0 4-2 0 4-3 0 4-4 0 4-5 0 4-6 0
Model BC-2002/CRC Tandem List of Effective Pages
Subheading and Page Rev Subheading and Page Rev
LEP-2 January 31, 2004
SECTION 5. TOW BAR (OPTIONAL) 5-1 0 5-2 0 5-3 0 5-4 0 5-5 0 5-6 0 5-7 0 5-8 0
SECTION 6. MAINTENANCE 6-1 0 6-2 0 6-3 0 6-4 0 6-5 0 6-6 0 6-7 0 6-8 0
SECTION 7. ILLUSTRATED PARTS LIST 7-1 0 7-2 2 7-3/7-4 0 7-5 0 7-6 0 7-7/7-8 0 7-9/7-10 0 7-11 0 7-12 0 7-13 0 7-14 0 7-15/7-16 0 7-17 2 7-18 0 7-19 0 7-20 0 7-21 0 7-22 0 7-23/7-24 0 7-25 0 7-26 0 7-27/7-28 0 7-29 2 7-30 0 7-31 0 7-32 0 7-33 0 7-34 0 7-35 0
7-36 0 7-37/7-38 0 7-39 0 7-40 0 7-41/7-42 0 7-43 0 7-44 0 7-45/7-46 0 7-47 0 7-48 0 7-49 0 7-50 0 7-51 0 7-52 0 7-53/7-54 0 7-55 0 7-56 0 7-57 0 7-58 0 7-59/7-60 0 7-61 0 7-62 0 7-63 2 7-64 0 7-65 2 7-66 0 7-67/7-68 0 7-69 1 7-70 1 7-71/7-72 0 7-73 0 7-74 0 7-75/7-76 0 7-77 2 7-78 0 7-79/7-80 0 7-81 2 7-82 0 7-83/7-84 0 7-85 0 7-86 0 7-87 0 7-88 0
Model BC-2002/CRC Tandem List of Effective Pages
Subheading and Page Rev Subheading and Page Rev
January 31, 2004 LEP-3
SECTION 8. DIAGRAMS 8-1 0 8-2 0 8-3/8-4 0 8-5/8-6 0 8-7/8-8 0 8-9/8-10 0 8-11/8-12 0 8-13/8-14 0 8-15/8-16 0 8-17/8-18 0 8-19/8-20 0 8-21/8-22 0 8-23/8-24 0 8-25/8-26 0 8-27 0 8-28 0 8-29 0 8-30 0 8-31 0 8-32 0 8-33 0 8-34 0 8-35 0 8-36 0 8-37/8-38 0 8-39 0 8-40 0 8-41/8-42 0 8-43 0 8-44 0 8-45 0 8-46 0 8-47/8-48 0 8-49 0 8-50 0 8-51/8-52 0 8-53 0 8-54 0 8-55 0 8-56 0 8-57 0 8-58 2 8-59 2 8-60 2
SECTION 9. PARTS INDEX 9-1 1 9-2 1 9-3 1 9-4 1 9-5 1 9-6 1 9-7 1 9-8 1 9-9 1 9-10 1 9-11 1 9-12 1 9-13 1 9-14 1 9-15 1 9-16 1
Model BC-2002/CRC Tandem List of Effective Pages
LEP-4 January 31, 2004
Blank Page
Model BC-2002/CRC Tandem Table of Contents
July 15, 2002 TC-1
TABLE OF CONTENTS
Subject Page
SECTION 1. DESCRIPTION........................................................................................................ 1-1
Equipment Description.......................................................................................................... 1-1
Power Train........................................................................................................................... 1-2
Aggregate Delivery System .................................................................................................. 1-2
Spread Hopper...................................................................................................................... 1-3
Gate Control Valve Box ........................................................................................................ 1-5
Computerized Rate Control (CRC)....................................................................................... 1-6
Chassis ................................................................................................................................. 1-7
Hydraulically Powered Remote Control Hitch....................................................................... 1-7
BC-2002/CRC Tandem Specifications ................................................................................. 1-8
SECTION 2. SAFETY PRECAUTIONS ....................................................................................... 2-1
Personal Safety..................................................................................................................... 2-1
Safety Rules.......................................................................................................................... 2-1
SECTION 3. PREPARING EQUIPMENT FOR USE.................................................................... 3-1
Initial Checkout of Machine................................................................................................... 3-1
Control Panel Switches......................................................................................................... 3-2
Computer Controls................................................................................................................ 3-4
Setting Spread Hopper Width ............................................................................................... 3-9
Weight Calibration .............................................................................................................. 3-11
Distance Calibration............................................................................................................ 3-13
Operator Station Adjustments............................................................................................. 3-14 Control Panel ................................................................................................................. 3-14 Bi-View Mirrors .............................................................................................................. 3-14
Hitch Adjustments............................................................................................................... 3-14 Height ............................................................................................................................ 3-14 Fore and Aft ................................................................................................................... 3-14
Chip Spreader Hitch Bar Requirements ............................................................................. 3-14
Model BC-2002/CRC Tandem Table of Contents
TC-2 July 15, 2002
SECTION 4. OPERATING INSTRUCTIONS............................................................................... 4-1
Mechanical Startup ............................................................................................................... 4-1
Operation .............................................................................................................................. 4-2
Setting Gate Opening for Manual Operation ........................................................................ 4-3
Clearing a Clogged Gate ...................................................................................................... 4-4
Shutdown on Completion of a Job........................................................................................ 4-4
SECTION 5. TOW BAR (OPTIONAL) ......................................................................................... 5-1
Towing Requirements........................................................................................................... 5-2
SECTION 6. MAINTENANCE...................................................................................................... 6-1
Scheduled Maintenance ....................................................................................................... 6-1
Routine Maintenance............................................................................................................ 6-3 Weight Calibration ........................................................................................................... 6-3 Distance Calibration ........................................................................................................ 6-4 Potentiometer Calibration ................................................................................................ 6-5
Replacement Filters, Belts and Fans.................................................................................... 6-7
Lubrication Specifications ..................................................................................................... 6-8
SECTION 7. ILLUSTRATED PARTS LIST ................................................................................. 7-1
SECTION 8. DIAGRAMS............................................................................................................. 8-1
SECTION 9. PARTS INDEX ........................................................................................................ 9-1
Model BC-2002/CRC Tandem Table of Contents
March 31, 2002 TC-3
LIST OF FIGURES
Figure Title Page
Figure 1-1. Model BC-2002/CRC Tandem, Curb Side..................................................1-1
Figure 1-2. Model BC-2002/CRC Tandem, Street Side ................................................1-1
Figure 1-3. Spread Hoppers at Minimum 10-foot Width................................................1-3
Figure 1-4. Spread Hoppers Extended to 20-foot Width ...............................................1-4
Figure 1-5. Gate Control Valve Box Interior ..................................................................1-5
Figure 1-6. Chassis Dimensions ...................................................................................1-7
Figure 3-1. Control Panel ..............................................................................................3-2
Figure 3-2. Computer Controls – View 1.......................................................................3-4
Figure 3-3. Computer Controls – View 2.......................................................................3-6
Figure 3-4. Examples of the Use of Computerized Gate Controls ................................3-7
Figure 3-5. Computer Controls – View 3.......................................................................3-7
Figure 3-6. Computer Controls – View 4.......................................................................3-8
Figure 3-7. Spread Hopper Remote Control Box ..........................................................3-9
Figure 3-8. Manual Gate Switches..............................................................................3-10
Figure 3-9. Computer Display During Distance Calibration ........................................3-13
Figure 3-10. Hitch Bar Location on Dump Truck.........................................................3-15
Figure 3-11. Typical Hitch Bar.....................................................................................3-15
Figure 4-1. Cam Open Indicator....................................................................................4-3
Figure 5-1. Tow Bar ......................................................................................................5-3
Figure 5-2. Wheel Placement and Removal Position....................................................5-3
Figure 5-3. Position No. 1 Loading Chip Spreader .......................................................5-4
Figure 5-4. Rear View, Coupling Pins ...........................................................................5-4
Figure 5-5. Position No. 2 Loading Chip Spreader .......................................................5-5
Figure 5-6. Position No. 3 Loading Chip Spreader .......................................................5-5
Figure 5-7. “Trailering” Jack and Pintle Eye..................................................................5-6
Figure 5-8. Truck Hitch and Hookups ...........................................................................5-6
Figure 5-9. Position No. 4 Loading Chip Spreader .......................................................5-7
Figure 6-1. Cam Shaft and Gate Grease Fittings..........................................................6-2
Figure 6-2. Checking Gate Opening .............................................................................6-2
Figure 6-3. Computer Display During Distance Calibration ..........................................6-4
Model BC-2002/CRC Tandem Table of Contents
TC-4 March 31, 2002
Figure 6-4. Potentiometer Guard ..................................................................................6-6
Figure 6-5. Potentiometer .............................................................................................6-6
Figure 7-1. Model BC-2002/CRC Tandem (Complete) .................................................7-4
Figure 7-2 (Sheet 1). Tandem Chip Spreader Assembly ..............................................7-8
Figure 7-2 (Sheet 2). Tandem Chip Spreader Assembly ............................................7-10
Figure 7-3. Engine/Hydrostatic Installation .................................................................7-16
Figure 7-4. Drivelines ..................................................................................................7-19
Figure 7-5. Exhaust System........................................................................................7-20
Figure 7-6. Frame Assembly.......................................................................................7-24
Figure 7-7. Wishbone Assembly .................................................................................7-28
Figure 7-8. Spherical Bearing .....................................................................................7-31
Figure 7-9. Panel Assembly, 2-Wheel Drive ...............................................................7-32
Figure 7-10. Panel Assembly, 4-Wheel Drive .............................................................7-34
Figure 7-11. Conveyor Assembly, Left-Hand ..............................................................7-38
Figure 7-12. Conveyor Assembly, Right-Hand............................................................7-42
Figure 7-13. Tube/Steering Assembly.........................................................................7-46
Figure 7-14. Junction Box ...........................................................................................7-48
Figure 7-15. Oil Cooler Assembly ...............................................................................7-50
Figure 7-16. Pedestal and Control Box Assembly ......................................................7-54
Figure 7-17. Hitch Assembly .......................................................................................7-56
Figure 7-18. Hitch Lift..................................................................................................7-60
Figure 7-19. Hitch Manifold W/Out Lift Option ............................................................7-62
Figure 7-20. Hitch Manifold W/Lift Option ...................................................................7-64
Figure 7-21. Chip Box, Tandem..................................................................................7-68
Figure 7-22. Potentiometer Assembly.........................................................................7-72
Figure 7-23. Gear Box Assembly ................................................................................7-76
Figure 7-24. Valve Box Assembly ...............................................................................7-80
Figure 7-25. Chip Box Extension ................................................................................7-84
Figure 7-26. Tow Bar Assembly..................................................................................7-86
Figure 7-27. Heat Exchanger ......................................................................................7-88
Figure 8-1. Console Wiring Detail, Tandem (2000 – 2001)...........................................8-3
Figure 8-2. Console Wiring Detail, Tandem (2002).......................................................8-5
Figure 8-3. Junction Box Wiring Detail, Tandem (2000 – 2001) ...................................8-7
Model BC-2002/CRC Tandem Table of Contents
March 31, 2002 TC-5
Figure 8-4. Junction Box Wiring Detail, Tandem (2002) ...............................................8-9
Figure 8-5. Valve Box Wiring Detail, Tandem (2000 – 2001)......................................8-11
Figure 8-6 (Sheet 1). Valve Box Wiring Detail, Tandem (2002)..................................8-13
Figure 8–6 (Sheet 2). Valve Box Wiring Detail, Tandem (2002) .................................8-15
Figure 8-7. Slave Box Wiring Detail, Tandem (2000 – 2001)......................................8-17
Figure 8-8. Slave Box Wiring Detail, Tandem (2002)..................................................8-19
Figure 8-9. Digital Foot Control Wiring Detail, Tandem (2002) ...................................8-21
Figure 8-10. Engine Wiring Detail, Tandem................................................................8-23
Figure 8-11. Lights Wiring Detail.................................................................................8-25
Figure 8-12. Air System Hose and Fitting Diagram, 2-Wheel Drive............................8-37
Figure 8-13. Air System Hose and Fitting Diagram, 4-Wheel Drive............................8-41
Figure 8-14. Spread Hopper Gate Air System ............................................................8-47
Figure 8-15. Hydraulic/Misc. Hose and Fittings ..........................................................8-51
Model BC-2002/CRC Tandem Table of Contents
TC-6 March 31, 2002
List of Tables
Table Title Page
Abbreviation/Definition Table INTRO-2
Table 1-1. Gate Control Valve Box Functions 1-6
Table 1-2. Specifications 1-8
Table 3-1. Control Panel Switches 3-3
Table 3-2. Control Functions for Figure 3-2 3-5
Table 3-3. Control Functions for Figure 3-3 3-6
Table 3-4. Control Functions for Figure 3-5 3-7
Table 3-5. Control Functions for Figure 3-6 3-8
Table 6-1. Scheduled Preventive Maintenance 6-1
Table 6-2. BearCat Part Numbers 6-7
Table 7-1. Recommended Spare Parts 7-2
Table 8-1. BC-2002/CRC Tandem Electrical Circuit 8-27
Table 8-2. Air System Hose and Fittings, 2-Wheel Drive 8-39
Table 8-3. Air System Hose and Fittings, 4-Wheel Drive 8-43
Table 8-4. Air System Parts and Fittings Chart 8-45
Table 8-5. Air System Hose and Fittings, Spread Hopper Gates, Front and Rear 8-49
Table 8-6. Hydraulic/Misc. Hose and Fittings 8-53
Table 8-7. Hydraulic System Parts and Fittings Chart 8-58
Model BC-2002/CRC Tandem Introduction
March 31, 2002 INTRO-1
INTRODUCTION
BearCat Chip Spreaders (Model BC-2002/CRC Tandem) are designed and manufactured to ensure personnel safety when the equipment is operated properly and all safety precautions are strictly followed.
Persons responsible for the operation and field maintenance of the Model BC-2002/CRC Tandem Chip Spreader should read this manual carefully before attempting to operate the equipment or performing any service or adjustment procedures on it.
NOTE: BearCat Manufacturing assumes no liability for accident or injury incurred through improper use of this equipment.
WARNING: BEARCAT CHIP SPREADERS MOVE LARGE AMOUNTS OF ABRASIVE MATERIAL AT HIGH SPEEDS. THIS EQUIPMENT CONTAINS EXPOSED MOVING PARTS AND BELTS. THE HYDRAULIC SYSTEM OPERATES AT HIGH PRESSURE AND THE FLUID AND LINES CAN REACH HIGH TEMPERATURES. POTENTIALLY LIFE-THREATENING HAZARDS MAY EXIST DURING EQUIPMENT OPERATION. PERSONNEL MUST BE TRAINED AND FAMILIAR WITH SECTION 2 (SAFETY PRECAUTIONS) BEFORE OPERATING BEARCAT EQUIPMENT.
WARNING: POTENTIALLY LIFE-THREATENING HAZARDS MAY EXIST DURING EQUIPMENT OPERATION. ONLY QUALIFIED PERSONNEL SHOULD ATTEMPT TO OPERATE, SERVICE OR MAKE ADJUSTMENTS TO THE BEARCAT EQUIPMENT.
WARNING: FOLLOW THESE PRECAUTIONARY INSTRUCTIONS EXACTLY. DO NOT TAKE SHORTCUTS. DO NOT ASSUME THAT SOMEONE ELSE HAS ACTED ON YOUR BEHALF. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN DEATH OR SERIOUS INJURY. IF ANY RULE OR PRECAUTION IS NOT CLEAR TO YOU, SEE YOUR SUPERVISOR BEFORE USING THE MACHINE.
Model BC-2002/CRC Tandem Introduction
INTRO-2 March 31, 2002
Abbreviation/Definition Table
Abbreviation Definition
CRC Computerized Rate Control
CCW Counterclockwise
CW Clockwise
PSY Pounds-per-square-yard
KgSM Kilograms-per-square-meter
FPM Feet-per-minute
MPM Meters-per-minute
PSI Pounds-per-square-inch
Model BC-2002/CRC Tandem Description
March 31, 2002 1-1
SECTION 1. DESCRIPTION
Equipment Description
The Model BC-2002/CRC Tandem Computer Controlled, Self-propelled Chip Spreader is illustrated in Figure 1-1 and Figure 1-2. The following description of the equipment should be read for familiarity with the operating features and capabilities of the Model BC-2002/CRC Tandem Chip Spreader.
Figure 1-1. Model BC-2002/CRC Tandem, Curb Side
Figure 1-2. Model BC-2002/CRC Tandem, Street Side
Model BC-2002/CRC Tandem Description
1-2 March 31, 2002
Power Train
Model BC-2002/CRC Tandem is equipped with a 6-cylinder diesel engine. The engine crankshaft is coupled to an axial-piston, high torque hydrostatic pump, and a hydrostatic transmission and two-speed transfer case which drives a limited-slip front axle.
The particular configuration of the Model BC-2002/CRC Tandem power train, consisting of front drive (limited-slip), hydrostatic transmission and transfer case, and single hydraulic motor, provides outstanding control and traction far exceeding that previously available. As an example, Model BC-2002/CRC Tandem is capable of pulling a fully loaded 15 cubic yard dump truck up a 15% grade from a dead stop.
In addition, the hydraulic motor is equipped with a Low-Lock function. With Low-Lock selected, the hydraulic motor is held in full displacement by an electrically actuated solenoid. Low-Lock acts as a speed-limiting device and eliminates any undesired acceleration by the chip spreader on downhill grades.
An optional four-wheel drive system is available for terrain/gradeability situations that require additional traction or control.
Aggregate Delivery System
Model BC-2002/CRC Tandem employs two hydraulically driven 30-inch wide conveyor belts to move aggregate from the receiving hopper to the spread hoppers. The belts form a 30° -trough angle, which increases the belt load capacity. They are capable of carrying twice the volume of rock while running only 2/3 as fast as a conventional 20-inch flat belt. The belt motion is controlled by solenoid-actuated valves that receive signals from level-sensing diaphragm switches mounted at the top of each spread hopper.
NOTE: Optional belts are rated at 350 °F (for use with hot aggregate).
The conveyor belt return rollers employ a self-cleaning design that prevents any accumulation of asphalt when the machine is used to spread precoated aggregate. Other than periodic lubrication of the shaft bearings, as specified in Section 6 of this manual, no maintenance is required for the conveyor belt return rollers.
Model BC-2002/CRC Tandem Description
March 31, 2002 1-3
Spread Hopper
Model BC-2002/CRC Tandem is equipped with two separate (front and rear) spread hoppers that can be quickly extended from a minimum width of 10 feet to a maximum width of 20 feet. Hopper extension and retraction is controlled from the operator’s station or from a remote control box at the top of the right-hand conveyor. By using the computer controlled aggregate gates, the operator can spread material at any width from 1 foot to 20 feet. Figure 1-3 shows the spread hoppers retracted to the minimum width of 10 feet.
Figure 1-3. Spread Hoppers at Minimum 10-foot Width
Hydraulic power is used to extend the front or rear spread hopper to the desired overall width. Each hopper can be extended or retracted independently for offset and special clearance applications. The hoppers may also be extended or retracted simultaneously for equal width applications. The front hopper extends to the left and the rear hopper extends to the right. Once the maximum spread width is established, the appropriate aggregate gates are selected from the operator’s station on the chip spreader. Figure 1-4 shows the spread hoppers extended to their maximum width of 20 feet.
Model BC-2002/CRC Tandem Description
1-4 March 31, 2002
Figure 1-4. Spread Hoppers Extended to 20-foot Width
The operator controls all gates individually from the operator’s station. The independently controlled spread hoppers eliminate the need to manually add or remove aggregate gates to accomplish spread width changes. With the hoppers retracted to the 10-foot width, the machine is readily transportable.
Each spread hopper uses a hydraulically driven, 14-inch diameter, abrasion resistant auger to ensure even distribution of the aggregate across the hopper. The 10 aggregate gates on each spread hopper are pneumatically actuated and provide instant response to any computer controlled or manual input. There is no agitator bar or spread roller to wear or limit production.
The spread hoppers have a total capacity of 3.8 cubic yards. The struck capacity of the receiving hopper is 4.5 cubic yards. These capacities allow the Model BC-2002/CRC Tandem to operate for longer periods than conventional units in situations where the chip spreader cannot be accompanied by a dump truck.
Optional spread hopper extensions are available. The extension adds 12 inches to the outside end of each hopper. This option increases the total spread width capability of the chip spreader to 22 feet.
Model BC-2002/CRC Tandem Description
March 31, 2002 1-5
Gate Control Valve Box
A gate control valve box is mounted on each spread hopper. Each valve box contains the solenoid valves that control the functions of the individual hopper. The solenoid valves can be manually controlled at the box, but are normally controlled from the operator’s station. The interior of a valve box is shown in Figure 1-5.
Figure 1-5. Gate Control Valve Box Interior
The functions of the components within the valve box are described in Table 1-1. The numbers in the table refer to the item numbers in Figure 1-5.
Model BC-2002/CRC Tandem Description
1-6 March 31, 2002
Table 1-1. Gate Control Valve Box Functions
No. Description Function
1 Hydraulic valve Controls spread hopper hydraulic functions
2 Switch (cam OPEN/CLOSE) Manually controls the cam
Manually operates gates Used for computer calibration
3 Electro-pneumatic valves 1 thru 10
Controls air flow to open or close the gates
4 Toggle switches 1 thru 10 Provides manual control to open and close individual gates
Used for setup and cleaning Used for manual operation
Computerized Rate Control (CRC)
Model BC-2002/CRC Tandem employs an onboard computer working with appropriate sensors to provide full automatic control of the aggregate flow at all times. Accuracy is assured for sand, rock, or any kind of coated or uncoated aggregate material. The computerized control system performs the following functions:
• Constantly measures the actual rate at which aggregate is being delivered
• Correlates the actual rate with the travel speed of the chip spreader
• Compares the actual flow rate to the rate selected by the operator
The computer then uses the information obtained from these three sources (actual aggregate flow, vehicle speed, and desired aggregate flow rate) to maintain the desired rate at all times. The system automatically adjusts the aggregate flow through the spread hopper gates.
Because the computer constantly monitors the speed of the vehicle, automatic rate control is maintained regardless of speed variations such as those encountered when the chip spreader moves up or down a grade or when accelerating or decelerating. Control is also constant whether the chip spreader is moving forward or backward.
It is important to note that the computerized control system responds instantaneously to changes in vehicle speed or to the selection of a different spread rate by the operator. Therefore, there is never any lag time. The actual rate at which aggregate is laid on the surface is always instantly maintained at the selected level required.
Changes in the width of the spread pattern, as for tapered areas, are accomplished by pressing the appropriate switches on the computer control panel. The corresponding gates are instantly closed, and the spread width varies accordingly. The operator does not need to leave his position to make these changes.
Regardless of the spread width selected, or the changes made during a run, the spread rate is automatically maintained at the selected level of aggregate distribution.
Model BC-2002/CRC Tandem Description
March 31, 2002 1-7
Chassis
The chassis members are channel steel, bolted rather than welded, for maximum repairability. The length of the chassis, as shown in Figure 1-6, permits a wheelbase of 158.5 inches. This length, in combination with rubber spring suspension on the front axle, assures smooth, steady control.
The BC-2002/CRC Tandem is 10 feet wide when the spread hoppers are fully retracted and 20 feet wide when the spread hoppers are fully extended.
Figure 1-6. Chassis Dimensions
Hydraulically Powered Remote Control Hitch
The hydraulically operated hitch provides positive hooking and unhooking in any of a wide range of relative positions and angles between the chip spreader and the dump truck. The hitch is actuated through a switch on the operator’s control panel.
NOTE: When equipped with the optional hitch lift, hitch height is also adjustable from the operator’s control panel.
Model BC-2002/CRC Tandem Description
1-8 January 31, 2004
BC-2002/CRC Tandem Specifications
Table 1-2 lists general specifications for the BC-2002/CRC Tandem Chip Spreader.
Table 1-2. Specifications
Hydrostatic Drive System
Type Front-wheel drive, closed-loop feedback control system
Transmission Axial piston variable rate high torque hydrostatic pump directly coupled to engine; variable rate hydraulic motor drives axle through 2-speed transfer case
Transfer Case 2-Speed, high-low range, manually shifted, with remote oil cooler
Operating Mode LOW Range (0-600 FPM) (Low-Lock engaged, 0-300 FPM)
HIGH Range (0-1600 FPM) (18 MPH) (Low-Lock engaged, 0-700 FPM)
NOTE: In low range the unit will pull a fully loaded 15 cubic yard dump truck up a 15% grade from a dead stop.
Diesel Engine
Pre March 2003
Cummins 5.9 liter, turbocharged. Electric start, alternator, dual batteries, dry-type air cleaner. Variable speed governor
Diesel Engine
March 2003/2004
Cummins QSB 5.9 liter, Inter-cooled turbocharger, with electric start, alternator, dual batteries, dry-type air cleaner and variable speed governor. Emissions compliant
Frame Main: 10 1/8 in. X 3 ½ in. channels
Cross members: 10 in. X 3 in. channels
Rear Axle
2-WD Solid trailer axle (5 in. diameter tube)
4-WD Rear drive axle with planetary gear hubs, over-all 17.1 to 1 reduction, solid mount
Rating (both) 25,000 lb
Front Axle
Type Drive/steering axle with planetary gear hubs, over-all 17.1 to 1 reduction, 42° steering angle; dual rubber spring suspension; 31,800 lb rating
Steering
Type Hydraulically powered orbital
Control Hand wheel; no mechanical linkage
Brakes
Front Wet disc, air over hydraulic
Model BC-2002/CRC Tandem Description
January 31, 2004 1-9
Table 1-2. Specifications
Rear (2-WD) 16.5 in. X 7 in. drum S-cam air brake, Anchorlok parking brake
Rear (4-WD) Wet disc, air over hydraulic
Parking Spring applied, hyd. released. Fail-safe driveline brake June 2005
Wheels Disc, front and rear interchangeable
Tires Truck type, 385/65R X 22.5 highway tread
Positive Lock Hitch
Type Hydraulically powered, positive grab and release
Adjustment Range 8 in. to 20 in. height, 6 in. fore and aft
Hydraulic System
Type Variable-volume, pressure compensated piston pump
Drive Engine crankshaft
Configuration Independent circuits for each conveyor and box function
Reservoir 70-gallon capacity, two 10-micron absolute return filters
Cooling Hydraulically driven oil cooler with total return flow capacity
Power Steering Engine-mounted vane pump feeding twin load-sensing closed-center steering valves (excess pump flow powers positive lock hitch)
Receiving Hopper
Width 10 feet
Struck Capacity 4.5 cubic yards (3.44 cubic meters); includes rubber skirting to prevent spilling
Spread Hopper
Width 10 feet (each)
Capacity Total 3.8 cubic yards (2.9 cubic meters)
Spread Width 1 to 20 feet, hydraulically actuated
Spread Rate Range 1-160 lbs per-square-yard
Spread Rate Control
Computer controlled CRC system
Cut-Off Gates Electro-pneumatic powered; 12 inches wide; infinite gate opening adjustment and preset capability from operator’s station
Conveyors
Belt Width 30 in.
Trough Angle 30°
Belt Rating 2-ply
Model BC-2002/CRC Tandem Description
1-10 January 31, 2004
Table 1-2. Specifications
Drive Independent hydraulic motors
Motion Control By solenoid valves through spread hopper-mounted level sensors
Conveyors (continued)
Conveyor Protection
Lined on each side; self-cleaning tail pulleys and return rollers; hooded deflectors at each head pulley
Operator’s Station Left-hand and right-hand adjustable cushioned seats with adjustable suspension; left-hand and right-hand adjustable tilt steering wheels; swing-over control/instrument panel with brake pedal and speed control
Controls and Instruments
Operator’s Panel Controls - ignition switch, hitch, spread width and rate controls, hydrostatic transmission, parking brake, augers, conveyor belts, transfer case, engine throttle; lockable covers included
Instruments - fuel, hydraulic temperature, engine temperature, engine RPM, hour meter, oil pressure, charging system voltage, air pressure
Safety Equipment Ladders on each side; safety hand rails; electric backup alarm; warning horn, strobe light, turn/flasher/stop lights, and tractor type night work lights
Miscellaneous
Empty Weight 25,000 lbs
Additional Equipment
80-gallon fuel tank; deck-mounted tool boxes under seats
Over All Dimensions With spread hoppers retracted and standard tires
Length 27 feet
Width 10 feet
Height 9 feet 3 in.
Ground Clearance 10 in.
Wheel Base 13 feet 2 1/2 in.
Turning Radius 19.5 feet
Front Approach Angle 18°
Rear Approach Angle 20°
Tread
Front 82 in.
Rear 104 in.
NOTE: As part of a continuing program of product improvement, BearCat Mfg., Inc. reserves the
Model BC-2002/CRC Tandem Description
January 31, 2004 1-11
Table 1-2. Specifications
right to make changes in Model BC-2002/CRC Tandem specifications at any time.
Model BC-2002/CRC Tandem Safety Precautions
March 31, 2002 2-1
SECTION 2. SAFETY PRECAUTIONS
Personal Safety
Persons responsible for the operation and maintenance of BearCat Chip Spreaders should read the following precautions and the remainder of this manual carefully before operating the equipment.
WARNING: ALWAYS REMEMBER THAT CHIP SPREADING MACHINES CAN BE DANGEROUS. THEY CONTAIN EXPOSED MOVING PARTS AND BELTS, AND THEY MOVE LARGE AMOUNTS OF ABRASIVE MATERIAL AT HIGH SPEED. YOU MUST OPERATE THIS MACHINE CAREFULLY TO PROTECT YOURSELF FROM PAINFUL OR EVEN FATAL INJURY. HAZARDS ASSOCIATED WITH THIS MACHINE, AND THE NECESSARY PRECAUTIONS TO AVOID DANGER, ARE GIVEN IN THIS MANUAL.
Safety Rules
Read each safety rule and make them a part of your daily work routine.
WARNING: FOLLOW THESE PRECAUTIONARY INSTRUCTIONS EXACTLY. DO NOT TAKE SHORTCUTS. DO NOT ASSUME THAT SOMEONE ELSE HAS ACTED ON YOUR BEHALF. IF ANY RULE OR PRECAUTION IS NOT CLEAR TO YOU, SEE YOUR SUPERVISOR BEFORE USING THE MACHINE.
• Keep clear of all moving parts.
• Stay out of the hoppers when diesel engine is running.
• Keep hands away from gates when connecting air hoses.
• Use caution around the conveyor belts and augers. They can start automatically.
• Keep clear of rear handrail. Contact with the dump truck tailgate is possible.
• Keep clear of the hitch. You could be injured if it actuates against any part of your body.
• Engage the parking brake and place the hydrostatic transmission in neutral before leaving the machine.
• Stop the engine before crawling under the machine.
• Keep the surface of the hydraulic oil cooler clear of obstructions.
NOTE: BearCat Manufacturing assumes no liability for accident or injury incurred through improper use of this equipment.
Model BC-2002/CRC Tandem Safety Precautions
2-2 March 31, 2002
Blank Page
Model BC-2002/CRC Tandem Preparing Equipment for Use
March 31, 2002 3-1
SECTION 3. PREPARING EQUIPMENT FOR USE
This section contains information the operator must know in order to prepare the Model BC-2002/CRC Tandem Chip Spreader for safe and proper spreading operations.
WARNING: OPERATORS MUST READ AND UNDERSTAND THIS MATERIAL BEFORE ATTEMPTING TO USE THE MACHINE. FAILURE TO FOLLOW THESE OPERATING INSTRUCTIONS MAY RESULT IN DEATH OR SERIOUS INJURY TO PERSONNEL.
CAUTION: THE INITIAL CHECKOUT PROCEDURES GIVEN BELOW ARE MINIMUM REQUIREMENTS. FAILURE TO PERFORM THESE STEPS CAN RESULT IN DAMAGE TO THE EQUIPMENT AND UNSAFE OPERATING CONDITIONS.
Initial Checkout of Machine
1. Make sure all fluid levels are adequate.
NOTE: Use Shell Tellus 100 or equivalent type 100 oil if the hydraulic system or the brake master cylinder level is low.
A. Hydraulic fluid – the sight glass is located behind the left front fender brace.
B. Brake master cylinder – located on the left side of the chassis.
C. Engine oil – the dipstick is located on the left side of the engine.
WARNING: RADIATOR SHOULD BE COOL TO THE TOUCH PRIOR TO REMOVING RADIATOR CAP. ESCAPING STEAM OR HOT LIQUID MAY CAUSE BURNS.
D. Radiator coolant – check the fluid level at the radiator cap.
2. Check the hydraulic line filters.
NOTE: If the gauge readings exceed 10 inches when the fluid is warm, replace the associated filter element.
3. Visually inspect the tires, hoses, fittings, and belts.
4. Make sure the receiving hopper is filled with the appropriate aggregate for the job.
Model BC-2002/CRC Tandem Preparing Equipment for Use
3-2 March 31, 2002
Control Panel Switches
Operators should thoroughly understand the functions of all of the control panel switches as shown in Figure 3-1 and listed in Table 3-1.
Figure 3-1. Control Panel
Model BC-2002/CRC Tandem Preparing Equipment for Use
March 31, 2002 3-3
Table 3-1. Control Panel Switches
Switch Function
L BELT AUTO: ON position enables the left belt to run until the spread hopper diaphragm switch turns it off.
OFF: The belt is off.
MAN: Manually runs the belt.
R BELT AUTO: ON position enables the right belt to run until the spread hopper diaphragm switch turns it off.
OFF: The belt is off.
MAN: Manually runs the belt.
HOPPER SHIFT
FRONT (): Extends and retracts the front spread hopper only.
REAR (): Extends and retracts the rear spread hopper only.
HOPPER SHIFT BOTH
OUT (): Extends both front and rear spread hoppers simultaneously.
IN (): Retracts both front and rear spread hoppers simultaneously.
FRONT AUGER
AUTO: ON position enables the front auger to run until the diaphragm switch turns it off.
OFF: The auger is off.
MAN: Manually runs the auger.
REAR AUGER
AUTO: ON position enables the rear auger to run until the diaphragm switch turns it off.
OFF: The auger is off.
MAN: Manually runs the auger.
HITCH OPEN: Used to open the hitch.
CLOSED: Used to close the hitch.
HITCH LIFT
Optional Equipment
UP: Moves the hitch up.
DOWN: Moves the hitch down.
FWD-REV. Selects forward, neutral, or reverse function for the hydrostatic drive.
MAXIMUM SPEED CONTROL
Variable speed control for hydrostatic drive. Used to adjust FPM rate of chip spreader. Turn knob CW to increase speed, turn knob CCW to decrease speed.
MASTER Manually controls the air cylinders that operate the gates. Must be ON for any gate to open in CRC operation.
LOW-LOCK ON: Actuates solenoid on hydraulic motor, engages motor full displacement speed-limiting function.
OFF: Normal hydraulic motor operation.
Model BC-2002/CRC Tandem Preparing Equipment for Use
3-4 March 31, 2002
Table 3-1. Control Panel Switches
Switch Function
LIGHTS ON: Turns work, tail, and clearance lights on.
OFF: Turns lights off.
BEACON Turns amber warning beacon on and off.
IGNITION Used to control chip spreader engine ignition system.
Computer Controls
Operators should thoroughly understand the computer controls and functions, which are shown in Figure 3-2 thru Figure 3-6 and listed in Table 3-2 thru Table 3-5.
Figure 3-2. Computer Controls – View 1
3
2
1
4 5 6 7 8 9
10
11
Model BC-2002/CRC Tandem Preparing Equipment for Use
March 31, 2002 3-5
Table 3-2. Control Functions for Figure 3-2
No. Control Function
1 SET Used in all computer functions to save a setting.
2 (Rate Select Switch)
Used to change the PSY or spread rate.
3 AUTO Used to change from CRC to manual rate control. The default setting is CRC. To control the cam manually, press and hold the AUTO switch for 5 seconds. The PSY will disappear on the screen and the Rate Control Switches will now control the cam openings (speed variations will no longer affect the cam opening). To return to CRC, press and hold the AUTO switch again for 5 seconds, the PSY will reappear and the computer will resume control of the cam opening.
4 CONTRAST Used to increase or decrease the computer control panel display contrast. Adjust display for different lighting conditions.
5 � Indicates a break in communication between the master computer and the slave unit (check computer connection).
6 PSY (KgSM) Use the Rate Select switch to change the application.
7 OPEN Indicates the cam position; the cam controls how much the gates open. The computer controls the cam in relation to ground speed and desired rate.
8 FPM (MPM) Indicates the travel speed.
9 FEET Indicates the distance covered while spreading (it does not calculate width). It starts measuring when any gate is open. This number continually keeps track of the total distance spread, which will be reset to zero when the machine is shut off.
10 ZERO
Resets the FEET to zero (press and hold for 5 seconds to clear the distance measurement).
11 CAL Used to calibrate the spread rate and the footage. The computer must be calibrated when there is a change in aggregate size and weight. DO NOT confuse this with spread rate. Once the computer is calibrated for a particular aggregate, the spread rate can be changed at any time. Press and hold the switch for 5 seconds for aggregate calibration mode. Press it again in aggregate calibration mode for footage calibration.
Model BC-2002/CRC Tandem Preparing Equipment for Use
3-6 March 31, 2002
Figure 3-3. Computer Controls – View 2
Table 3-3. Control Functions for Figure 3-3
No. Control Function
Indicates the selected gates are open (the star ٭ 1disappears when the selected gates are closed).
2 GATE SELECTION INDICATOR
Indicates which gates are selected to open. Each black square represents a gate on the hoppers.
3 GATE COUNT Indicates how many gates are open (spread width).
4 ON Opens all selected gates.
5 OFF Closes all gates.
6
DISPLAY Changes to the current view whenever a GATE SELECTION, ON, or OFF switch is pressed (after several seconds the display will change back to the original view).
7
(Gate Select Switches)
Used to select which gates will open. These switches can also be used to control spread width while spreading.
1
2 3
4
5
6
7
Model BC-2002/CRC Tandem Preparing Equipment for Use
March 31, 2002 3-7
The gate select switches can also be used to control or change spread width while spreading. Figure 3-4 shows several spread pattern examples.
Figure 3-4. Examples of the Use of Computerized Gate Controls
Figure 3-5. Computer Controls – View 3
Table 3-4. Control Functions for Figure 3-5
No. Control Function
1 (Gate Select Switch) Reselects or opens gates from a previous selection.
2 (Gate Select Switch) Pressing this switch repeatedly closes the gates from left to right. Note: The OPEN INDICATOR ( ) is not visible, indicating that all gates are closed and you are just making a gate selection.
3 GATE COUNT Indicates the number of gates selected (in this case, only one gate is selected).
٭
1
2
3
Model BC-2002/CRC Tandem Preparing Equipment for Use
3-8 March 31, 2002
Figure 3-6. Computer Controls – View 4
Table 3-5. Control Functions for Figure 3-6
No. Control Function
1 (Gate Select Switch) Reselects or opens gates from a previous selection.
2 (Gate Select Switch) In this example, closes or deselects gates from the left to the middle.
3 [ ] Shows selected gates are open.
4 GATE COUNT Indicates the number of gates selected (4 gates in this example).
5 OPEN Opens all selected gates.
6 CLOSE Closes all gates.
7 (Gate Select Switch) In this example, closes or deselects gates from the right to the middle.
8 (Gate Select Switch) Reselects or opens gates from a previous selection.
1
2
3 4
5
6
7
8
Model BC-2002/CRC Tandem Preparing Equipment for Use
March 31, 2002 3-9
Setting Spread Hopper Width
WARNING: ALWAYS KEEP YOUR FINGERS CLEAR OF THE AGGREGATE GATES. IF A GATE SHOULD CLOSE UNEXPECTEDLY, SERIOUS PERSONAL INJURY MAY RESULT.
WARNING: KEEP CLEAR OF ALL MOVING PARTS. THE SPREAD HOPPERS ARE HYDRAULICALLY ACTUATED. IMPROPER OR UNSAFE OPERATION MAY CAUSE SERIOUS PERSONAL INJURY.
1. Determine the maximum spread width required for the job.
2. Use the HOPPER SHIFT switches on the control panel (Figure 3-1), or the remote control box at the top of the right-hand conveyor (Figure 3-7), to extend the spread hoppers to the desired position.
Figure 3-7. Spread Hopper Remote Control Box
Model BC-2002/CRC Tandem Preparing Equipment for Use
3-10 March 31, 2002
3. Test the aggregate gates for free movement using the manual gate control switches located in each valve box (Figure 3-8).
Figure 3-8. Manual Gate Switches
4. Fill the hoppers and perform the WEIGHT CALIBRATION and DISTANCE CALIBRATION procedures.
Model BC-2002/CRC Tandem Preparing Equipment for Use
March 31, 2002 3-11
Weight Calibration
WARNING: POTENTIALLY LIFE-THREATENING HAZARDS MAY EXIST DURING EQUIPMENT OPERATION. ONLY QUALIFIED PERSONNEL SHOULD ATTEMPT TO OPERATE, SERVICE, OR MAKE ADJUSTMENTS TO THE BEARCAT EQUIPMENT.
Proper weight calibration ensures the computer controlled aggregate gates are opening to the exact extent required to deposit the specified amount of aggregate, under all operating conditions.
This procedure should be performed on a level surface.
NOTE: It is not necessary to perform the weight calibration with all gates open. Select a spread width that allows the operator to cover the canvas (4 to 6 feet).
This weight calibration should be carried out whenever the aggregate material is changed to one of a different type or from a different source.
1. Fill the hoppers with the new aggregate.
2. Place the yard-square piece of canvas (furnished) on the scale provided and set the scale to zero.
3. Lay the canvas out flat on level ground.
4. Switch the CRC unit ON and use the controls to enter the PSY (pounds-per-square-yard) value desired for the job.
5. On the Control Panel, position the following switches to AUTO or ON:
R and L BELTS
FRONT and REAR AUGER
MASTER
6. With the engine running at 1800-2000 RPM and the transfer case in LOW, drive the machine as follows:
A. Set the SPEED control fully CCW and the FWD-REV switch to FWD.
B. Press the foot pedal down.
C. Turn the SPEED control CW. The machine will begin moving after about three full turns. Turn the control to obtain the approximate expected spreading speed for the job.
Model BC-2002/CRC Tandem Preparing Equipment for Use
3-12 March 31, 2002
7. Drive toward the canvas square. Position the gate switch to OPEN to begin spreading just before reaching the canvas square (the chip spreader must be traveling at the required speed for the job).
8. After passing over the canvas, position the gate switch to CLOSE and stop the machine by releasing the foot pedal.
9. Use the scale to weigh the canvas with the deposited aggregate.
10. If the actual weight differs from the value entered in Step 4, press and hold the CAL switch (Figure 3-9). The display will instruct you to enter the actual weight of the aggregate sample.
11. Use the “ ” controls to enter the actual weight.
12. Press the SET switch. The display will show the PSY value entered in Step 4.
NOTE: If the difference between the entered PSY and the actual weight is large, a second calibration run may be necessary. If necessary, repeat Step 7 thru Step 12.
Model BC-2002/CRC Tandem Preparing Equipment for Use
March 31, 2002 3-13
Distance Calibration
Proper distance calibration ensures the correlation between machine ground speed and chip-spreading density is accurately maintained through the distance-measuring circuits in the CRC computer.
This procedure should be performed once in each operating season. It is not necessary that the receiving hopper or spread hoppers be filled.
1. With the engine running and the SPEED control fully CCW, position the CRC computer POWER switch to ON. Refer to Figure 3-1 and Figure 3-9 for the control locations.
Figure 3-9. Computer Display During Distance Calibration
2. Press ZERO to zero the FEET display.
3. Set the FWD-REV switch to FWD, press the foot pedal all the way down and turn the SPEED control CW until the display indicates approximately 300 FPM.
4. Position the gate switch to OPEN and drive a carefully measured distance of 1000 feet.
5. At exactly 1000 feet, position the gate switch to CLOSE and stop the machine by releasing the foot pedal. The FEET display should now read approximately 1000.
6. Press and hold CAL twice, holding the switch down approximately five seconds each time.
7. Press “ “ to lower the displayed FEET value or to raise it, until it reads 1000.
Model BC-2002/CRC Tandem Preparing Equipment for Use
3-14 March 31, 2002
8. When the display reads 1000, press SET. The distance calibration is now complete. The machine is in the normal operating mode.
9. Note the new distance (footage) calibration number and enter it on the title page of this manual. The computer control can be reset to this number if the box is replaced or the number is changed. If this number is used, the unit will not require a complete distance calibration.
Operator Station Adjustments
Control Panel
Select on which side of the machine to operate. The control panel swings left or right by pulling the spring loaded pin at the base and pushing the assembly left or right. During the course of the workday, the operator may change sides. Set up both sides comfortably.
Bi-View Mirrors
Optional bi-view mirrors are designed to give the operator a view of the blind side of the machine and the level of aggregate in each spread hopper. The mirror opposite to the operator’s position gives a view of the blind side and the end of the spread hopper. The mirror on the same side of the operator gives a view of the center of the hoppers.
Hitch Adjustments
Height
The hitch can be adjusted up and down using the chains. Pick the hitch up with one hand and move the links in or out of the slots, as desired.
NOTE: An optional hydraulic hitch lift can be adjusted from the control panel.
Fore and Aft
The hitch fore and aft adjustments are located between the conveyor rails underneath the chipper. Pull the spring pin and remove the bolt, there are four holes for adjustment.
NOTE: Be sure to replace the bolt, nut and spring pin.
Chip Spreader Hitch Bar Requirements
The location and measurements required to position the chip spreader hitch bar on the aggregate supply dump truck are shown in Figure 3-10. Figure 3-11 shows an example of the hitch bar. The exact positioning of the hitch bar is required for consistent aggregate flow to the receiving hopper without unnecessary spillage.
Model BC-2002/CRC Tandem Preparing Equipment for Use
March 31, 2002 3-15
Figure 3-10. Hitch Bar Location on Dump Truck
Figure 3-11. Typical Hitch Bar
Model BC-2002/CRC Tandem Preparing Equipment for Use
3-16 March 31, 2002
Blank Page
Model BC-2002/CRC Tandem Operating Instructions
March 31, 2002 4-1
SECTION 4. OPERATING INSTRUCTIONS
Mechanical Startup
Before starting the Chip Spreader, complete the fluid checks and visual inspection described under SECTION 3. PREPARING EQUIPMENT FOR USE.
WARNING: YOUR CONTINUED GOOD HEALTH AND EVEN YOUR LIFE MAY DEPEND ON FOLLOWING THE RULES OF OPERATION SET FORTH IN THIS MANUAL. ALWAYS REMEMBER THAT CHIP SPREADING MACHINES CAN BE DANGEROUS. THEY CONTAIN EXPOSED MOVING PARTS AND BELTS, AND THEY MOVE LARGE AMOUNTS OF ABRASIVE MATERIAL AT HIGH SPEED. YOU MUST OPERATE THIS MACHINE CAREFULLY TO PROTECT YOURSELF FROM PAINFUL OR EVEN FATAL INJURY. HAZARDS ASSOCIATED WITH THIS MACHINE, AND THE NECESSARY PRECAUTIONS TO AVOID DANGER, ARE GIVEN IN THIS MANUAL.
1. Set the following controls as specified:
• SET PARKING BRAKE (PULL)
• R and L BELTS (OFF)
• FRONT and REAR AUGER (OFF)
• FWD-REV NEUTRAL
• TRANSFER CASE NEUTRAL
• T-HANDLE START UP VALVE (PULL)
• RELEASE THROTTLE (PULL UP)
2. Start the engine and use the hand throttle to set it at 1000 RPM. Push the T-Handle Start Up Valve back.
3. Extend the spread hoppers to the desired width for the job.
4. Set the following controls as specified:
• MASTER ON
• R and L BELTS AUTO
• FRONT and REAR AUGER AUTO
5. Use the “ “ computer controls to enter the PSY or KgSM value desired for the job. The PSY or the KgSM may be adjusted during the run if necessary.
6. Release the parking brake.
Model BC-2002/CRC Tandem Operating Instructions
4-2 March 31, 2002
Operation
Drive the Chip Spreader as follows:
1. Set the FWD-REV switch to the desired direction.
2. Turn the SPEED control CW approximately ten turns, until it stops.
3. Select transfer case high or low range.
A. Move the transfer case shift lever to the desired position.
B. VERY SLOWLY AND GENTLY press the right foot pedal down to see if the chip spreader moves. Make sure the transfer case is in gear.
WARNING: KEEP CLEAR OF THE HITCH. YOU COULD BE INJURED IF IT ACTUATES AGAINST ANY PART OF YOUR BODY.
4. Adjust the hitch. On the control panel, push the HITCH switch to the OPEN position and hold for two seconds to open the hitch.
A. Back the chip spreader into the hitch bar of the aggregate supply dump truck. The driver of the dump truck should hold the brakes while the chip spreader is backed up.
B. To align the dump truck and chip spreader, center the bed of the dump truck within the receiving hopper opening.
NOTE: The optional hitch height can be adjusted from the control panel.
C. The mouth of the hitch should center itself vertically on the hitch bar. If the hitch mouth is not centered because it is too high or low, use the chains that the hitch hangs from to adjust the height.
D. With the chip spreader hitch mouth pushing against the dump truck hitch bar, push the HITCH switch to the CLOSED position for two seconds to close the hitch.
E. If the position of the dump bed is either too far into the receiving hopper or too far out, the hitch can be adjusted fore and aft 6 inches to compensate.
5. Fill the receiving hopper with aggregate.
A. Give the dump truck a small tug with the chip spreader to check if the hitch is locked.
B. Using hand signals, direct the dump truck operator to release the tailgate, tip the bed and dispense aggregate into the receiving hopper. The belts are still running from Step 4 in the Mechanical Startup. The spread hoppers should start filling with aggregate.
Model BC-2002/CRC Tandem Operating Instructions
March 31, 2002 4-3
Setting Gate Opening for Manual Operation
This procedure enables the use of the machine in a nonautomatic mode.
1. With the engine running and the CRC computer switched OFF, use the cam switches located in each valve box to set the cam indicators (Figure 4-1) to the same value at which the machine has been operating.
2. Turn the MASTER switch OFF.
WARNING: ALWAYS KEEP CLEAR OF THE AGGREGATE GATES. IF A GATE SHOULD OPEN OR CLOSE UNEXPECTEDLY, SERIOUS PERSONAL INJURY COULD RESULT.
3. Open individual gates with switches 1 thru 10 and 11 thru 20 (located in the valve boxes) as required for the job.
4. Set the CRC SPEED control to the number of turns that most nearly corresponds to the actual FPM at which the machine has been running.
5. Drive the machine up to speed, then turn the MASTER switch ON to open the gates and OFF to close the gates.
Figure 4-1. Cam Open Indicator
Model BC-2002/CRC Tandem Operating Instructions
4-4 March 31, 2002
NOTE: When operating in the manual mode, it is important to remember that any open gate will remain open the same distance no matter what speed the machine is driven. There is NO automatic control of PSY during manual override. In the manual mode, the most effective way to change PSY is by changing speed with the CRC SPEED control. Speed variations as small as 2% can readily be made with this control. As speed is raised, PSY decreases.
6. Upon completing the run, use the cam switch to return the cams to the closed position and close the gates.
Clearing a Clogged Gate
WARNING: NEVER INSERT YOUR HAND INTO A GATE. ALWAYS USE A METAL BAR OR ROD TO CLEAR AN OBSTRUCTION FROM A GATE. FAILURE TO DO SO MAY RESULT IN SERIOUS PERSONAL INJURY.
If a gate becomes plugged by a rock, perform the following:
1. Open the gate from the appropriate spread hopper valve box.
2. Use the cam switch in the valve box to set the cam fully open.
3. Open the clogged gate with the individual gate switch.
4. Remove the clog with a metal bar or rod.
5. When the clog is cleared, remove the metal bar and return the switches to their normal positions.
Shutdown on Completion of a Job
At the end of the job, perform the following steps:
NOTE: Step 1 and Step 2 should always be done unless the aggregate is so dry that there is no danger of caking.
1. Empty the spread hoppers.
2. Empty the receiving hopper.
3. Set the switches as follows:
• MASTER (ON)
• R and L BELTS (OFF)
• FRONT and REAR AUGER (OFF)
• CRC (OFF)
Model BC-2002/CRC Tandem Operating Instructions
March 31, 2002 4-5
4. To transport the machine to another location, accomplish the following steps:
A. Retract the spread hoppers to the 10-foot width.
B. Rotate the SPEED control fully CCW and set the FWD-REV switch to the NEUTRAL position.
5. If the optional tow bar is used, see the instructions in SECTION 5. TOW BAR (OPTIONAL).
6. Shut off the engine and set the parking brake.
Model BC-2002/CRC Tandem Operating Instructions
4-6 March 31, 2002
Blank Page
Model BC-2002/CRC Tandem Tow Bar
March 31, 2002 5-1
SECTION 5. TOW BAR (OPTIONAL)
WARNING: STAY OUT FROM UNDER THE TOW BAR AND CHIP SPREADER WHEN THEY ARE RAISED AND SUPPORTED BY THE HYDRAULIC LIFT CYLINDER. DEATH OR PERSONAL INJURY MAY OCCUR.
NOTE: The optional tow bar can only be used on 2-Wheel Drive models.
1. Position the tow bar on a hard, flat surface.
2. Using the “trailering” jack, disconnect the tow bar from the pickup or dump truck and lower the tow bar, raising the tires off the ground as shown in Figure 5-1.
3. Remove the tow bar tires and stow them in the tow bar (Figure 5-2).
4. Carefully drive the chip spreader up to the tow bar, centering it for attachment (Figure 5-3).
WARNING: THE CHIP SPREADER ENGINE MUST BE SHUT DOWN WHILE DISCONNECTING OR RECONNECTING HYDRAULIC HOSES. DEATH OR PERSONAL INJURY MAY OCCUR.
5. Connect the long 1/4 inch hydraulic hoses on the tow bar to the quick disconnects located on the street side of the front spread hopper. The tow bar valve controls the tow bar lift cylinder.
6. Position the wood blocks (5 in. X 8 in. X 48 in.) in front of the chip spreader as shown in Figure 5-3.
7. Raise the tow bar with the hydraulic lift cylinder as shown in Figure 5-3.
8. Carefully drive the chip spreader onto the wood blocks, keeping the tow bar centered (Figure 5-5).
NOTE: A large pry-bar is helpful in aligning the pins.
9. Adjust the pin-eye height with the lift cylinder and install the coupling pins and safety pins (Figure 5-4 and Figure 5-5).
CAUTION: DO NOT USE THE TRAILERING JACK TO RAISE THE CHIP SPREADER. DAMAGE TO THE TRAILERING JACK MAY OCCUR.
10. Raise the chip spreader and the tow bar with the hydraulic lift cylinder until the front chipper tires are at least 10 inches off the ground (Figure 5-6).
11. Adjust the pintle eye to match the towing vehicle (Figure 5-7). Torque the pintle eye bolts to 300 FT-LB.
Model BC-2002/CRC Tandem Tow Bar
5-2 March 31, 2002
12. Couple the tow bar to the towing vehicle.
13. Remove the wood blocks from under the chip spreader.
14. Make the air and light connections at each end of the tow bar (Figure 5-5 and Figure 5-8).
15. Change the air valve to the “Towing” position (located near the air glad-hand connection at the rear of the tow bar on the chip spreader).
16. Check the air brake operation from the towing vehicle, ensuring the rear brakes on the chip spreader function with the towing vehicle brakes.
17. Check all signal, brake and tail lights. Ensure they coordinate with the towing vehicle lights.
18. Attach the safety chains (2) to the towing vehicle (Figure 5-8 and Figure 5-9).
19. Double check the safety pins on the coupling pins at the rear of the tow bar (Figure 5-4).
Towing Requirements
WARNING: FAILURE TO COMPLY WITH THE FOLLOWING MINIMUM TOWING REQUIREMENTS COULD RESULT IN ACCIDENTAL SEPARATION OF THE CHIP SPREADER FROM THE TOW VEHICLE WHILE IN TRANSIT, CAUSING A POTENTIALLY DEADLY SITUATION.
1. The towing vehicle must be three axle, ten wheel (minimum) with a GVW of 52,000 lb. minimum (40,000 RAWR, 12,000 FAWR).
2. The pintle hook must be rated at 80,000 lb. towing capacity and 15,000 lb. vertical load minimum (Figure 5-8). The pintle must be mounted no more than 56 inches rear of the tandem suspensions trunion (Figure 5-9).
3. A combination hitch X-member complete with pintle and chipper hook bar can be supplied by BearCat (Part No. BRK-50960, Hitch and Hook Bar Assembly, MSC-50960 Premier 580 solid pintle coupling).
Model BC-2002/CRC Tandem Tow Bar
March 31, 2002 5-3
Figure 5-1. Tow Bar
Figure 5-2. Wheel Placement and Removal Position
Model BC-2002/CRC Tandem Tow Bar
5-4 March 31, 2002
Figure 5-3. Position No. 1 Loading Chip Spreader
Figure 5-4. Rear View, Coupling Pins
Model BC-2002/CRC Tandem Tow Bar
March 31, 2002 5-5
Figure 5-5. Position No. 2 Loading Chip Spreader
Figure 5-6. Position No. 3 Loading Chip Spreader
Model BC-2002/CRC Tandem Tow Bar
5-6 March 31, 2002
Figure 5-7. “Trailering” Jack and Pintle Eye
Figure 5-8. Truck Hitch and Hookups
Model BC-2002/CRC Tandem Tow Bar
March 31, 2002 5-7
Figure 5-9. Position No. 4 Loading Chip Spreader
Model BC-2002/CRC Tandem Tow Bar
5-8 March 31, 2002
Blank Page
Model BC-2002/CRC Tandem Maintenance
March 31, 2002 6-1
SECTION 6. MAINTENANCE
Scheduled Maintenance
Table 6-1. Scheduled Preventive Maintenance
Period Maintenance
Daily
1. Drain accumulated moisture from the air tanks.
2. If using precoated aggregate: to prevent buildup, parts of the machine exposed to the aggregate must be prelubricated with a suitable biodegradable solvent. These areas must be lubricated at every stop during the work shift.
Weekly
1. Grease the four fittings per foot on the camshaft and gates (Figure 6-1).
a. One on the shaft on each side of the gates.
b. One on the bottom of the gate.
c. One on the rear of the gate.
2. Grease the head bearings on the front and rear belt rollers (two fittings per roller).
Monthly
3. Grease the rear brakes’ S-cam bushings (2-WD model).
4. Grease both ends of the tie rod.
5. Grease both ends of the steering cylinder.
6. Grease the top and bottom of both steering knuckles.
7. Grease both ends of the drivelines.
8. Grease the front axle yoke bearing.
9. Verify the accuracy of the gate openings:
WARNING: TO AVOID INJURY KEEP FINGERS CLEAR OF THE GATE. SUDDEN OR UNEXPECTED MOVEMENT COULD CAUSE SERIOUS PERSONAL INJURY.
a. Set switches as follows:
CRC OFF MASTER ON MANUAL GATE SWITCHES (all) OPEN
b. Set the cam to the CLOSED position.
c. Set any gate to a measured 3/4-inch opening.
d. Adjust remaining gates to a 3/4-inch opening, using a 3/4-inch square tube as a feeler gauge (Figure 6-2).
NOTE: The grease used in all of these procedures is chassis grease.
Model BC-2002/CRC Tandem Maintenance
6-2 March 31, 2002
Figure 6-1. Cam Shaft and Gate Grease Fittings
Figure 6-2. Checking Gate Opening
Model BC-2002/CRC Tandem Maintenance
March 31, 2002 6-3
Routine Maintenance
Weight Calibration
WARNING: POTENTIALLY LIFE-THREATENING HAZARDS MAY EXIST DURING EQUIPMENT OPERATION. ONLY QUALIFIED PERSONNEL SHOULD ATTEMPT TO OPERATE, SERVICE, OR MAKE ADJUSTMENTS TO THE BEARCAT EQUIPMENT.
Proper weight calibration ensures the computer controlled aggregate gates are opening to the exact extent required to deposit the specified amount of aggregate under all operating conditions.
This procedure should be performed on a level surface.
NOTE: It is not necessary to perform the weight calibration with all gates open. Select a spread width that allows operator to cover the canvas (4 to 6 feet).
Weight calibration should be carried out whenever the aggregate material is changed to one of a different type or from a different source.
1. Fill the spread hoppers with the new aggregate.
2. Place the yard-square piece of canvas (furnished) on the scale provided and set the scale to zero.
3. Lay the canvas out flat on level ground.
4. Switch the CRC unit ON and use the controls to enter the PSY (pounds-per-square-yard) value desired for the job.
5. On the Control Panel, position the following switches to AUTO or ON:
• R and L BELTS
• FRONT and REAR AUGER
• MASTER
6. With the engine running at 1800-2000 RPM and the transfer case in LOW, drive the machine as follows:
A. Set the SPEED control fully CCW and the FWD-REV switch to FWD.
B. Press the foot pedal down.
C. Turn the SPEED control CW. The machine will begin moving after about three full turns. Turn the control to obtain approximately the expected spreading speed for the job.
Model BC-2002/CRC Tandem Maintenance
6-4 March 31, 2002
7. Drive toward the canvas square. Position the gate switch to OPEN to begin spreading just before reaching the canvas square (the chip spreader must be traveling at the required speed for the job).
8. After passing over the canvas, position the gate switch to CLOSE and stop the machine by releasing the foot pedal.
9. Use the scale to weigh the canvas with the deposited aggregate.
10. If the actual weight differs from the value entered in Step 4, press and hold the CAL switch. The display will instruct you to enter the actual weight of the aggregate sample.
11. Use the “ ” controls to enter the actual weight.
12. Press the SET switch. The display will show the PSY value entered in Step 4.
NOTE: If the difference between the entered PSY and the actual weight is large, a second calibration run may be necessary. In that event, repeat Step 7 thru Step 12.
Distance Calibration
Proper distance calibration ensures the correlation between machine ground speed and chip-spreading density is accurately maintained through the distance-measuring circuits in the CRC computer.
This procedure should be performed once in each operating season. It is not necessary that the receiving hopper or spread hoppers be filled. Refer to Figure 6-3 for the location of the controls.
Figure 6-3. Computer Display During Distance Calibration
Model BC-2002/CRC Tandem Maintenance
March 31, 2002 6-5
1. With the engine running and the SPEED control fully CCW, position the CRC computer POWER switch to ON.
2. Press ZERO to zero the FEET display.
3. Set the FWD-REV switch to FWD, press the foot pedal all the way down and turn the SPEED control CW until the display indicates approximately 300 FPM.
4. Position the gate switch to OPEN and drive a carefully measured distance of 1000 feet.
5. At exactly 1000 feet, position the gate switch to CLOSE and stop the machine by releasing the foot pedal. The FEET display should now read approximately 1000.
6. Press and hold CAL twice, holding the switch down approximately five seconds each time.
7. Press “ “ to lower the displayed FEET value or to raise it, until it reads 1000.
8. When the display reads 1000, press SET. The distance calibration is now complete and the machine is in the normal operating mode.
9. Note the new distance (footage) calibration number and enter it on the title page of this manual. The CRC computer can be reset to this number if the box is replaced or the number is changed. If this number is used, the unit will not require a complete distance calibration.
Potentiometer Calibration
The potentiometer (Pot) for each spread hopper is located on the outboard end of the camshaft and is protected by a heavy guard bolted to the end plate of the spread hopper (Figure 6-4). With the guard removed, the Pot can be accessed for repair or replacement (Figure 6-5). Perform the following steps to calibrate the Pot:
1. With the CRC computer POWER switch in the OFF position, press and hold the CAL switch and turn power ON.
2. Hold the switch in the CAL position until “SET POTS?” is shown on the CRC computer display and release the switch.
3. Immediately press the (up) switch to select YES and enter the Pot calibration mode.
4. When “MOVE CAMS NOW” is displayed, press the (up) switch to select YES and start cam movement and the Pot calibration routine. The CRC computer system will cycle the cam to the open and closed position and calibrate the Pot.
5. Once the cam has cycled and stopped, the Pot calibration is finished.
Model BC-2002/CRC Tandem Maintenance
6-6 March 31, 2002
Figure 6-4. Potentiometer Guard
Figure 6-5. Potentiometer
Model BC-2002/CRC Tandem Maintenance
March 31, 2002 6-7
Replacement Filters, Belts and Fans
Filters, belts and fans are not replaced during scheduled maintenance; they are replaced as needed. Table 6-2 lists BearCat’s part numbers for these components and the manufacturer’s part numbers.
Table 6-2. BearCat Part Numbers
Description Brand Part No.
BearCat
Part No. Qty
Hydraulic Components
Hydraulic Filters
Hydraulic Filter (100 Mesh) Hydraulic Filter (10 Micron) Hydraulic Filter (10 Micron 15 GPM)
Zinga Zinga Zinga
SE-100 SE-10 AE-10
FTR-22505 FTR-22502 FTR-51736
2 3 1
Cummins Engine Filters, Belt and Fan
Oil Filters
Oil Filter Fleet Guard LF3000 FTR-51260 1
Fuel Filters
Fuel Filter (Primary) Fuel Filter (Secondary) Pre-Fuel Filter
Fleet Guard Fleet Guard Fleet Guard
FS1280 FF5052 FS19512
FTR-51261 FTR-51262 FTR-51269
1 1 1
Water Filter
Water Filter (Service) Fleet Guard WF2071 FTR-60956 1
Air Filter
Air Filter (Primary) Air Filter (Secondary)
Fleet Guard Fleet Guard
AF418 AF490M
FTR-51265 FTR-51266
1 1
Belt
Fan Belt (Start Ser No. 45293079) Cummins 3926862 PTM-60961 1
Fan (Puller) Ky-Cadillac 4735-41393-35 MSC-51853 1
Model BC-2002/CRC Tandem Maintenance
6-8 March 31, 2002
Lubrication Specifications
The following list references the various types of lubricants that BearCat specifies for use on specific components of the BC-2002/CRC Tandem Chip Spreader.
Chassis Grease
• Gate Cylinder Ends
• Cam Bearings
• Gate Hinge Pins
• Head Pulley Bearings
• Auger Bearings
• Cam Lock Pivots
• Driveline (belt pump)
• Front and Rear Driveline (rear driveline 4-WD only)
• Trunion Bearing
• Take-Up Bearings (rear of conveyor)
• Spindle Bearings (top and bottom of axle)
• Tie Rod Ends
Cam Gear Box
Shell OMALA HD 460
Hydraulic Oil
Shell Tellus T 100 or equivalent (Shell Tellus 46 NOT used as of 05/20/00)
Texaco Rando HDZ 100 (Texaco Rando HD 46 NOT used as of 05/20/00)
Drive Axle Gear Oil
Must meet API GL-5 and MIL-PRF2105E qualifications
Shell Donax TD
Texaco TDH Oil
John Deere Hy-Gard Hy-Gard, Low Viscosity Hy-Gard Hy-Gard, Standard JDM J20C, or J20D Allison C-4
Cummins Engine Oil
Shell SAE 30 WT All Guard Diesel Oil
Model BC-2002/CRC Tandem Illustrated Parts List
March 31, 2002 7-1
SECTION 7. ILLUSTRATED PARTS LIST
Model BC-2002/CRC Tandem Illustrated Parts List
7-2 January 31, 2004
The following recommended spare parts list (Table 7-1) is provided as a guide to the user for convenience in the maintenance of Model BC-2002/CRC Chip Spreader. All of the parts listed are available from BearCat Manufacturing, Inc.
Table 7-1. Recommended Spare Parts
Description Part No. Quantity Belt Switch On/Off/Mom-On Single Pole ELC-51748 2
Switch, On/Off/On Single Pole Toggle ELC-24272 1
Switch, Fwd/Rev Switch 3 Pole 2 Position With Hesitation
ELC-51747 1
Switch, On/Off Single Pole Toggle ELC-24275 1
Switch, Mom-On/Off/Mom-On Single Pole Toggle ELC-24274 1
Switch, On/Off 2 Pole Toggle ELC-24267 1
Switch, High Temperature Level Control ELC-50915 1
Rheostat ELC-24288 1
Potentiometer, Geared (Modified) Thru 1999 ELC-50591 1
Potentiometer, 2000 and newer ELC-53128 1
Diaphragm, Material Level Switch MSC-50831 2
Air Solenoid Valve, 4-Way Versa C-7 VLV-50902 1
Connector Cable 6-Cond. ELC-26228 2
CRC Cable, 8-Cond. ELC-26235 30’
Gear Tooth Sensor Assembly ELC-26148 1
Cylinder Chipper Gate CYL-50703 1
Hinge Pin-Conveyor Belt FAS-51763 2
3’ X 3’ Canvas Calibration Bag MSC-51771 1
Calibration Scale, Weigh MSC-51749 1
Hydraulic Filter, Zinga FTR-22502 2
Hydraulic Filter 100 Mesh, Zinga FTR-22505 2
Hydraulic Filter, Water FTR-22508 1
Filter, Vent Breather FTR-22527 1
Fuel Filter, Primary FTR-51261 1
Fuel Filter, Secondary FTR-51262 1
Fuel Filter, Remote (inline) FTR-51269 1
Hydraulic Filter Zinga (case bleed) FTR-51736 1
Coolant Filter, Water Service FTR-60956 1
Air Filter, Primary FTR-51265 1
Air Filter, Safety FTR-51266 1
Oil Filter, (Chipper Engine) FTR-51260 1
Belt, Chipper Engine (start serial no. 45293079) PTM-60961 1
Model BC-2002/CRC Tandem Illustrated Parts List
7-3 Blank/7-4 March 31, 2002
Figure 7-1. Model BC-2002/CRC Tandem (Complete)
Model BC-2002/CRC Tandem Illustrated Parts List
March 31, 2002 7-5
Fig Item Description Part No. Qty 7-1 Chip Spreader, Tandem (Complete) BC-2002 RF
1 Tandem Chip Spreader Assembly BC-2002 (See Figure 7-2 for Details)
1
-2 Engine/Hydrostatic Installation (See Figure 7-3 for Details)
1
-3 Drivelines (See Figure 7-4 for Details)
1
-4 Spherical Bearing (See Figure 7-8 for Details)
1
5 Hitch Assembly (See Figure 7-17 for Details)
1
6 Hitch Lift (See Figure 7-18 for Details)
1
-7 Hitch Manifold W/Out Lift Option (See Figure 7-19 for Details)
1
-8 Hitch Manifold W/Lift Option (See Figure 7-20 for Details)
1
9 Chip Box, Tandem (See Figure 7-21 for Details)
2
-10 Chip Box Extension (See Figure 7-25 for Details)
1
NOTE: A dash (–) before the item number indicates the item is not illustrated on that figure.
Model BC-2002/CRC Tandem Illustrated Parts List
7-6 March 31, 2002
Blank Page
Model BC-2002/CRC Tandem Illustrated Parts List
7-7 Blank/7-8 March 31, 2002
Figure 7-2 (Sheet 1). Tandem Chip Spreader Assembly
Model BC-2002/CRC Tandem Illustrated Parts List
7-9 Blank/7-10 March 31, 2002
Figure 7-2 (Sheet 2). Tandem Chip Spreader Assembly
Model BC-2002/CRC Tandem Illustrated Parts List
March 31, 2002 7-11
Fig Item Description Part No. Qty 7-2 Tandem Chip Spreader Assembly BC-2002 RF
1 Support Panel, Right-Hand BRK-53083 1
3 Hex Bolt 1/2” – 13 X 1 1/4” AR
Lock-Washer 1/2” AR
Nut Hex 1/2” – 13 AR
6 Manifold MSC-53280 2
9 Hand Rail, Front (2000 – 2001) RNG-53307 1
12 Mirror GRD-61050 2
15 Mirror Base BRK-61051 2
18 Panel BRK-53299 1
21 Limit Switch Assembly MTR-53202 2
24 Seal RNG-53320 4
27 Door Assembly Left-Hand HSG-53294 1
Door Assembly Right-Hand HSG-53300 1
30 Guard Rail, Front Inside (2000 – 2001) GRD-53317 2
33 Conveyor Assembly, Right-Hand (See Figure 7-12 for Details)
HSG-53150 1
36 Guard Rail, Conveyor (2000 – 2001) GRD-61701 2
39 Manifold, Auger / Belt MSC-53376 1
42 Stiffener BRK-53257 1
45 Stiffener BRK-53260 3
48 Cross Member Aft BRK-53099 1
51 Cross Member Forward BRK-53100 1
54 Hex Bolt 3/8” – 16 X 1 1/4” 16
Lock-Washer 3/8” 16
Nut Hex 3/8” – 16 16
57 Coupling, Female PTM-60663 1
60 Coupling, Male PTM-60664 1
63 Taper Lock 1 1/2” PTM-60666 1
66 Taper Lock 1 15/16” PTM-60665 1
69 Mounting Plate BRK-51536 1
72 Belt Motor Assembly PTM-51619 2
75 Working Light ELC-51585 3
78 Air Intake Precleaner FTR-51855 1
81 Tube/Steering Assembly (2000 – 2001) (See Figure 7-13 for Details)
BRK-51529 1
84 Pedestal and Control Box Assembly (See Figure 7-16 for Details)
HSG-53372 1
87 Platform Mid HSG-53271 1
90 Platform Gripstrut GRD-53278 2
93 Oil Cooler Assembly (See Figure 7-15 for Details)
HSG-53233 1
96 Beacon ELC-24215 1
Model BC-2002/CRC Tandem Illustrated Parts List
7-12 March 31, 2001
Fig Item Description Part No. Qty 7-2 99 Receiving Hopper HSG-53365 1
102 Clamp, Vertical Seal BRK-51785 2
105 Seal, Vertical RNG-51795 2
108 Seal, 45 Corner RNG-53394 2
111 Hand Rail, Aft (2000 – 2001) GRD-51566 1
114 Seal, Horizontal RNG-51796 2
117 Seat MSC-51773 1
120 Clamp, Horizontal Seal BRK-51246 1
123 Clamp, Conveyor Rear Side Seal BRK-60647 4
126 Seal, Conveyor Flashing RNG-51793 4
129 Grizzly BRK-51846 2
132 Clamp, Conveyor Rear Seal BRK-51798 2
135 Seal, Horizontal Conveyor RNG-60645 2
138 Light Markers ELC-51596 2
141 Back-Up Alarm ELC-24293 1
144 Support, Receiving Hopper to Conveyor BRK-60614 2
147 Modified Axle Assembly (2WD) PTM-53348 1
150 Rear Drive Axle Assembly (4WD) PTM-53226 1
153 Platform with Seat Base, Right-Hand & Left-Hand HSG-53342 1
156 Horizontal Seal Stiffener, Outer BRK-51915 2
159 Horizontal Seal Stiffener, Inner BRK-51914 4
162 Wire Rope Clamp 3/4” FAS-51446 12
165 Hitch Assembly MCH-53216 1
168 Hitch X-Member BRK-53229 1
171 Channel Stiffener BRK-53241 1
174 Diesel Tank TNK-61824 1
177 Cap FIT-26045 1
180 Rear Fender GRD-51808 2
183 Bracket, Tank to Conveyor BRK-60604 2
186 Support, Upper BRK-60667 1
189 Ladder Assembly GRD-51528 1
192 Support, Lower BRK-60696 1
195 Bracket, Rear BRK-61479 2
198 Junction Box ELC-60950 1
201 Conveyor Assembly, Left-Hand (See Figure 7-11 for Details)
HSG-53149 1
204 Support Panel, Left-Hand BRK-53081 1
207 Hex Bolt 1/2” – 13 X 1 1/4” AR
Lock-Washer 1/2” AR
Nut Hex 1/2” – 13 AR
210 Hood HSG-61708 1
213 Brackets BRK-61696 AR
Model BC-2002/CRC Tandem Illustrated Parts List
March 31, 2002 7-13
Fig Item Description Part No. Qty 7-2 216 Bracket, Outer Conveyor Rail to Hydraulic Tank BRK-53355 2
219 Bracket, Inner Conveyor Rail to Hydraulic Tank BRK-51425 2
222 Track Support, Aft BRK-53366 1
225 Light, Turn ELC-51587 1
228 Bracket, Bearing Mount BRK-51416 4
231 Hex Bolt 3/8” – 16 X 1 1/4” 12
Lock-Washer 3/8” 12
Nut Hex 3/8” – 16 12
234 Pillow Block, Bearing PTM-51415 4
237 Hex Bolt 5/8” – 11 X 1 1/4” 8
Lock-Washer 5/8” 8
Nut Hex 5/8” – 11 8
240 Head Pulley Assembly PTM-61404 2
243 Track Support BRK-53087 1
246 Baffle BRK-53090 2
249 Cat Walk GRD-53311 1
252 Rock Box Panel Left-Hand, Front HSG-53291 1
255 Rock Box Panel Left-Hand, Rear HSG-53292 1
258 Seal Wiper RNG-53395 1
261 Panel, Right-Hand Side, Left-Hand Conveyor HSG-53295 1
264 Chain Assembly, Mirror FAS-61052 1
267 Rock Box End Panel, Left-Hand HSG-53293 1
270 Rock Box End Panel, Right-Hand HSG-53298 1
273 Slave Box Assembly HSG-53143 1
276 Bracket BRK-53353 2
279 Track Support, Front BRK-53341 1
282 Remote Box Assembly HSG-53331 1
285 Rock Box Panel Right-Hand, Front HSG-53296 1
288 Rock Box Panel Right-Hand, Rear HSG-53297 1
291 Seal Wiper RNG-53395 1
294 Cat Walk GRD-53133 1
297 Guard GRD-53411 1
300 Hand Rail, Front (2002) RNG-53424 1
303 Hand Rail, Front/Side (2002) RNG-53425 2
306 Guard Rail, Front Inside (2002) GRD-53429 2
309 Guard Rail, Conveyor (2002) GRD-53426 2
312 Tube/Steering Assembly (2002) (See Figure 7-13 for Details)
BRK-51529 1
315 Hand Rail, Aft (2002) GRD-51566 1
Model BC-2002/CRC Tandem Illustrated Parts List
7-14 March 31, 2001
Blank Page
Model BC-2002/CRC Tandem Illustrated Parts List
7-15 Blank/7-16 March 31, 2002
Figure 7-3. Engine/Hydrostatic Installation
Model BC-2002/CRC Tandem Illustrated Parts List
January 31, 2004 7-17
Fig Item Description Part No. Qty. 7-3 Engine/Hydrostatic Installation RF
1 Cummins 6CT 8.3 (230 HP) MCH-51849 1
2 Breather Assembly, Hydraulic Tank FTR-51539 1
3 Manifold, Pressure MSC-51600 1
4 Pump, Pressure Compensator, Belt Pump PMP-51618 1
5 Elbow, Compensator Pump FIT-60616 1
6 Swaybar Assembly PTM-51459 1
7 Mud Flap GRD-51815 2
8 Manifold, Return MSC-53371 1
9 Engine Mount Assembly, Rear BRK-51460 2
10 Exhaust System (See Figure 7-5 for Details)
MSC-51869 1
11 Fender Strut BRK-51805 4
12 Bracket, Air Cleaner Support BRK-51826 1
13 Valve, Shuttle, Sunstrand Pump VLV-53237 1
14 Bracket, Shuttle Valve, Sunstrand Pump BRK-53262 1
15 Front Fender GRD-51806 2
16 Pump, Sunstrand 90R, Hydrostatic Pump PMP-53230 1
17 Lifting Eye, Transfer Case BRK-53224 1
18 Transfer Case PTM-53160 1
19 Motor, Sunstrand 51V, Hydrostatic Motor PMP-53231 1
20 Frame Assembly (See Figure 7-6 for Details)
HSG-53135 1
21 Heat Exchanger, Transfer Case PMP-51925 1
22 Bracket, Cooler Mount BRK-53402 2
23 Radar Assembly (4-WD Option Only) HSG-53350 1
24 Fuel Filter Assembly, Primary FTR-60953 1
25 Air Dryer Assembly FTR-60945 1
26 Filter Head Assembly, Suction FTR-51731 1
27 Bracket Throttle Cable BRK-61681 1
28 Pump, Steering PMP-80016 1
29 Wishbone Assembly (See Figure 7-7 for Details)
HSG-53139 1
30 Timbren MSC-100130 4
31 Conical Nut FAS-61487 40
32 Wheel Adapter BRK-61491 2
33 Hydraulic Tank Assembly TNK-53158 1
34 Dip Stick 60” MTR-51862 1
35 Dip Stick Tube PIP-53303 1
36 Shield, Radiator GRD-51842 1
37 Radiator MSC-50814 1
Model BC-2002/CRC Tandem Illustrated Parts List
7-18 March 31, 2002
Model BC-2002/CRC Tandem Illustrated Parts List
January 31, 2004 7-19
Figure 7-4. Drivelines
Fig Item Description Part No. Qty. 7-4 Drivelines RF
1 Companion Flange 2-1-333 PTM-22273 1
2 Flange Yoke 2-2-329 PTM-22251 1
3 Flange Yoke 2-2-479 PTM-22252 1
4 U-Joint 1550 5 – 155x PTM-51548 2
5 Tube Shaft 4-40-761 1
6 Slip Yoke 4-3-1241KX 1
7 Flange Yoke 4-2-669 2
8 U-Joint 1550 5 – 155x PTM-51548 2
9 Tube Shaft 4-40-761 1
10 Slip Yoke 4-3-1241KX 1
11 Flange Yoke 4-2-669 2
Model BC-2002/CRC Tandem Illustrated Parts List
7-20 March 31, 2002
Figure 7-5. Exhaust System
Model BC-2002/CRC Tandem Illustrated Parts List
January 31, 2004 7-21
Fig Item No. Description Part No. Qty.
7-5 Exhaust System RF
1 Tail Pipe FIT-51884 1
2 Horizontal Mufflers MSC-51875 1
3 Muffler Hanger BRK-51877 1
4 Nipple Exhaust (4” X .083” Wall Tube X 6” Long) 1
5 Connector Tube FIT-51874 1
6 Elbow 18” X 18” 90 FIT-51873 1
7 Tube 4” X .083” W. Nipple Exhaust FIT-51885 1
8 Clamp U Guillotine Type FAS-51872 6
9 Elbow 18” X 18” 90 (6” Cut Off End) Modified FIT-51873
1
10 Clamp Connector Stainless Steel FIT-51871 2
11 Tubing Flex 4” X 10 1/2” FIT-51872 1
Model BC-2002/CRC Tandem Illustrated Parts List
7-22 March 31, 2002
Blank Page
Model BC-2002/CRC Tandem Illustrated Parts List
7-23 Blank/7-24 March 31, 2002
Figure 7-6. Frame Assembly
Model BC-2002/CRC Tandem Illustrated Parts List
March 31, 2002 7-25
Fig Item Description Part No. Qty. 7-6 Frame Assembly RF
1 Bracket, Double Timbren Spring BRK-61468 2
2 Bracket, Triple Return Filter BRK-51679 1
3 Bracket, Double Intake Filter BRK-51680 1
4 Baffle Air Dryer BRK-60948 1
5 Hex Bolt 1/4” – 20 X 1” 2
Flat Washer 1/4” 2
Lock-Washer 1/4” 2
Nut Hex 1/4” – 20 2
6 Right-Hand & Left-Hand Stanchion Plate BRK-51481 2
7 Bracket, Primary Fuel Filter BRK-60615 1
8 Hex Bolt 5/16” – 18 X 1 1/4” 2
Lock-Washer 5/16” 2
Nut Hex 5/16” – 18 2
9 Ring, Rear Frame Hosing RNG-53343 2
10 Ring, Chaffing 4” I.D. RNG-26422 1
11 Gusset BRK-61043 2
12 Panel Assembly, 2-Wheel Drive (See Figure 7-9 for Details)
HSG-61069 1
Panel Assembly, 4-Wheel Drive (See Figure 7-10 for Details)
BRK-61059 1
13 Stanchion Pipe, Wet Air Tank HSG-51473 1
14 Gusset BRK-20235 6
15 Front Engine Mount HSG-51472 1
16 Channel HSG-53381 1
17 Channel BRK-61485 1
18 Support Tube BRK-60925 1
19 Spacer 3/16” BRK-61440 1
20 Hook, Right-Hand BRK-51471 1
21 Hook, Left-Hand BRK-51472 1
22 Bracket Swaybar (Right-Hand & Left-Hand) BRK-51485 2
23 Gusset Pan Hard BRK-53141 2
24 Frame Rail, Left-Hand HSG-61481 1
25 Frame Rail, Right-Hand HSG-61480 1
26 Spacer Air Tank BRK-51573 2
27 Air Tank Assembly TNK-51993 1
28 Hex Bolt 7/16” – 14 X 1 1/4” 8
Flat Washer 7/16” 12
Lock-Washer 7/16” 8
Nut Hex 7/16” – 14 8
29 Battery Box HSG-51560 1
30 Tube X-Member Transmission Mount BRK-53223 1
Model BC-2002/CRC Tandem Illustrated Parts List
7-26 March 31, 2002
Fig Item Description Part No. Qty. 7-6 31 Hex Bolt 5/8” – 11 X 6 1/2” Gr. 8 2
Lock-Washer 5/8” 2
Nut Hex 5/8” – 11 2
32 Hex Bolt 5/8” – 11 X 8” Gr. 8 2
Lock-Washer 5/8” 2
Nut Hex 5/8” – 11 2
33 Plate, Conveyor to Frame HSG-53222 1
34 Quick Release Valve VLV-51642 1
35 1/2” Male Jic X 1/4” Male Pipe 8MJ-4MP 1
36 Hex Bushing 3/8” X 1/4” FIT-28342 1
37 1/4” Close Nipple FIT-28001 1
38 Hex Bolt 1/4” – 20 X 1 1/4” FAS-28703 2
Lock-Washer 1/4” FAS-28645 2
Nut Hex 1/4” – 20 FAS-28500 2
39 45# Fixed Regulator VLV-26201 1
40 Soc. Hd. Pipe Plug 1/4” FIT-28296 3
41 90 1/2” Male Jic X 1/4” Male Pipe 90D8MJ-4MP 1
Model BC-2002/CRC Tandem Illustrated Parts List
7-27 Blank/7-28 March 31, 2002
Figure 7-7. Wishbone Assembly
Model BC-2002/CRC Tandem Illustrated Parts List
January 31, 2004 7-29
Fig Item Description Part No. Qty. 7-7 Wishbone Assembly RF
1 Axle, Spicer/Dana HD 1350 PTM-61457 1
2 Plate, Left-Hand Top BRK-53137 1
3 Plate, Right-Hand Top BRK-53136 1
4 Spacer, Spherical Bearing PIP-51518 2
5 Nut 1 1/2” – 12 Esna (Nylon) Lock FAS-28593 1
6 Hex Bolt 1 1/2” – 12 X 8” Gr. 8 FAS-28999A 1
7 Channel HSG-53138 2
8 Plate, Bottom, Left-Hand & Right-Hand BRK-53134 2
9 Spacer BRK-53240 4
10 Chain Strap BRK-60797 2
11 Hex Bolt 3/4” – 10 X 8 1/2” CAT 8
Lock-Washer 3/4” CAT 16
Washer SAE 3/4” CAT 8
Nut Hex 3/4” – 10 CAT 8
12 Hex Bolt 9/16” – 12 X 1 3/4” Gr. 8 32
Lock-Washer 9/16” Gr. 8 32
Nut Hex 9/16” – 12 Gr. 8 32
13 Spacer, Tandem A-Frame HSG-53243 1
14 Parking Brake Assembly PTM-53235 1
15 Brake Mount BRK-53315 1
Sway Bar Assembly (not shown) PTM-51459 1
Model BC-2002/CRC Tandem Illustrated Parts List
7-30 March 31, 2002
Model BC-2002/CRC Tandem Illustrated Parts List
March 31, 2002 7-31
Figure 7-8. Spherical Bearing
Fig Item Description Part No. Qty. 7-8 Spherical Bearing RF
1 Nut Hex 3/8” – 16 FAS-28538 4
2 ¼” Grease Zerk .250-28M-2 1
3 Spherical Bearing PTM-51517 1
4 Spherical Bearing Retainer HSG-51513 2
5 Hex Bolt 3/8” – 16 X 2 ½” FAS-28736 4
Model BC-2002/CRC Tandem Illustrated Parts List
7-32 March 31, 2002
Figure 7-9. Panel Assembly, 2-Wheel Drive
Model BC-2002/CRC Tandem Illustrated Parts List
March 31, 2002 7-33
Fig Item Description Part No. Qty. 7-9 Panel Assembly, 2-Wheel Drive RF
1 Soc. Hd. Bolt 5/16” – 18 X 3” FAS-25483 2
2 Hitch Manifold (W/Fittings Only) HSG-61500 1
3 Bracket, Hitch Manifold, Tow Bar Glad Hand BRK-61048 1
4 Nut Hex 5/16” – 18 FAS-28501 2
Lock-Washer 5/16” FAS-28646 2
5 Soc. Hd. Screw 10 – 24 X 3/8” FAS-25451 2
6 Hex Bolt ¼” – 20 X 1” FAS-28702 2
Washer Flat ¼” FAS-28632 2
Lock-Washer ¼” FAS-28645 2
Nut Hex ¼” – 20 FAS-28500 2
7 Socket 7-Pole Trailer Conn. ELC-24245 1
Socket Boot ELC-24247 1
8 Glad Hand ELC-22375 2
9 ½” Male Pipe X ¾” Bulk Head X ½” Male Pipe 8MP-12BH-8MP 2
10 ½” Male Jic X ¼” Male Pipe 8MJ-4MP 1
11 Cable 7-Cond. Stranded Trailer Cable ELC-24058 10’
12 ¼” Male Jic X ¼” Male Pipe 4MJ-4MP 1
13 Valve S/S 3-Way Ball Valve VLV-29216 1
14 Bushing Hex ½” X ¼” FIT-28344 3
15 90 ¼” Male Jic X ¼” Male Pipe 90D4MJ-4MP 3
Model BC-2002/CRC Tandem Illustrated Parts List
7-34 March 31, 2002
Figure 7-10. Panel Assembly, 4-Wheel Drive
Model BC-2002/CRC Tandem Illustrated Parts List
March 31, 2002 7-35
Fig Item Description Part No. Qty. 7-10 Panel Assembly, 4-Wheel Drive RF
1 Master Cylinder PTM-51644 1
2 Hex Bolt 3/8” – 16 X 1 ¼” FAS-28732 4
Flat Washer 3/8” FAS-28634 4
Lock-Washer 3/8” FAS-28647 4
Nut Hex 3/8” – 16 FAS-28502 4
3 Hitch Manifold (W/Fittings Only) HSG-61500 1
4 Soc. Hd. Bolt 5/16” – 18 X 3” FAS-25483 2
Lock-Washer 5/16” FAS-28646 2
Nut Hex 5/16” – 18 FAS-28501 2
5 Bracket BRK-61048 1
Model BC-2002/CRC Tandem Illustrated Parts List
7-36 March 31, 2002
Blank Page
Model BC-2002/CRC Tandem Illustrated Parts List
7-37 Blank/7-38 March 31, 2002
Figure 7-11. Conveyor Assembly, Left-Hand
Model BC-2002/CRC Tandem Illustrated Parts List
March 31, 2002 7-39
Fig Item Description Part No. Qty. 7-11 Conveyor Assembly, Left-Hand RF
1 Take-Up Bearing Adjustment Assembly MCH-51965 2
2 Hex Bolt ½” – 13 X 1 ¼” 6
Lock-Washer ½” 6
Nut Hex ½” – 13 6
3 Tail Pulley Assembly MCH-51403 1
4 Take-Up Bearing PTM-51417 2
5 Hex Bolt 3/8” – 16 X 2 ½” 2
Nut Lock 3/8” – 16 2
6 Cat Walk, Left-Hand, Tandem GRD-53157 1
7 Return Rollers PTM-51413 5
8 Conveyor Rail #2 Left-Hand Inner, Tandem HSG-53152 1
9 Cross Channel HSG-51428 2
10 Plate, Rear Axle BRK-53225 1
11 Trough Rollers Assembly MCH-51402 6
12 Angle Brace BRK-61609 1
13 Bracket BRK-51407 10
14 Stub Shaft MCH-51412 10
15 Hex Bolt 3/8” – 16 X 1 ¼” 20
Lock-Washer 3/8” 20
Nut Hex 3/8” – 16 20
16 Cross Member BRK-61706 6
17 Hex Bolt 3/8” – 16 X 2 ½” 12
Flat Washer 3/8” 12
Nut Lock 3/8” – 16 12
18 Conveyor Rail #1 Left-Hand Outer, Tandem HSG-53151 1
Model BC-2002/CRC Tandem Illustrated Parts List
7-40 March 31, 2002
Blank Page
Model BC-2002/CRC Tandem Illustrated Parts List
7-41 Blank/7-42 March 31, 2002
Figure 7-12. Conveyor Assembly, Right-Hand
Model BC-2002/CRC Tandem Illustrated Parts List
March 31, 2002 7-43
Fig Item Description Part No. Qty. 7-12 Conveyor Assembly, Right-Hand RF
1 Take-Up Bearing Adjustment Assembly MCH-51965 2
2 Hex Bolt ½” – 13 X 1 ¼” 6
Lock-Washer ½” 6
Nut Hex ½” – 13 6
3 Tail Pulley Assembly MCH-51403 1
4 Take-Up Bearing PTM-51417 2
5 Hex Bolt 3/8” – 16 X 2 ½” 2
Nut Lock 3/8” – 16 2
6 Cat Walk, Right-Hand, Tandem GRD-53314 1
7 Return Roller Assembly PTM-51433 4
8 Conveyor Rail #3 Right-Hand Inner HSG-53153 1
9 Cross Channel HSG-51428 2
10 Trough Roller MCH-51402 5
11 Plate, Rear Axle BRK-53225 1
12 Angle Brace BRK-61610 1
13 Mount Angle Cylinder Hitch Lift BRK-61613 1
14 Bracket BRK-51407 10
15 Stub Shaft MCH-51412 10
16 Hex Bolt 3/8” – 16 X 1 ¼” 20
Lock-Washer 3/8” 20
Nut Hex 3/8” – 16 20
17 Cross Member BRK-53351 1
18 Hex Bolt 3/8” – 16 X 2 ½” 1
Cap Screw Flat Soc. Hd. 3/8” – 16 X 1” 1
Lock-Washer 3/8” 2
Flat Washer 3/8” 2
19 Cross Member With Guard BRK-53370 1
20 Hex Bolt 3/8” – 16 X 2 ½” 2
Lock-Washer 3/8” 2
Flat Washer 3/8” 2
21 Cross Member BRK-61706 4
22 Hex Bolt 3/8” – 16 X 2 ½” 8
Lock-Washer 3/8” 8
Flat Washer 3/8” 8
23 Conveyor Rail #4 Right-Hand Outer HSG-53154 1
Model BC-2002/CRC Tandem Illustrated Parts List
7-44 March 31, 2002
Blank Page
Model BC-2002/CRC Tandem Illustrated Parts List
7-45 Blank/7-46 March 31, 2002
Figure 7-13. Tube/Steering Assembly
Model BC-2002/CRC Tandem Illustrated Parts List
March 31, 2002 7-47
Fig Item Description Part No. Qty. 7-13 Tube/Steering Assembly RF
1 Platform Support/Forward Tube Assembly BRK-60673 1
2 Steering Shuttle Valve VLV-51605 1
Hex Bolt ¼” – 20 X 2 ¼” FAS-28707 2
Lock-Washer ¼” FAS-28645 2
3 Manifold, Steering MSC-60995 1
4 Soc. Hd. Cap Screw 5/16” – 18 X 3 ½” FAS-25493 2
Flat Washer 5/16” FAS-28646 2
Nut Hex 5/16” – 18 FAS-28501 2
Lock-Washer 5/16” FAS-28646 2
5 Junction Box (See Figure 7-14 for Details)
ELC-60931 1
6 Steering Wheel Cap MCH-51610 2
7 Steering Wheel Nut FAS-51611 2
8 Steering Wheel MCH-51609 2
9 ¼” Male O-Ring X ¼” Male Jic 4MB-4MJ 4
Cap ¼” Female Jic C4FJ 4
10 90 ¼” Male O-Ring X ¼” Male Jic 90D4MB-4MJ 1
11 3/8” Male O-Ring X ¼” Male Jic 6MB-4MJ 2
12 ½” Male O-Ring X ½” Male Jic 8MB-8MJ 8
13 90 ½” Male O-Ring X ½” Male Jic 90D8MB-8MJ 4
14 90 ¼” Male O-Ring X ¼” Male Jic 90D4MB-4MJ 2
15 ½” Male O-Ring X ½” Male Jic 8MB-8MJ 6
16 Inlet Check Valve VLV-51606 2
17 Valve Steering VLV-51607 2
18 Steering Column 30” MCH-51608 2
19 Clamp Muffler 1 ½” FAS-29362 2
NOTE: The Tube/Steering Assembly Hand Rail is changed for the 2002 model. See Figure 7-2 for differences. Specify model year when ordering a replacement hand rail.
Model BC-2002/CRC Tandem Illustrated Parts List
7-48 March 31, 2002
Figure 7-14. Junction Box
Model BC-2002/CRC Tandem Illustrated Parts List
March 31, 2002 7-49
Fig Item Description Part No. Qty. 7-14 Junction Box RF
1 Latch T-Handle FAS-24387 1
2 Screw Machine Rd. Hd. 10 – 32 X ¾” FAS-25834 7
Nut Hex 10 – 32 FAS-28554 7
3 Breaker 15 Amp ELC-24289 1
4 Flasher, Heavy Duty 2-Terminal ELC-101889 1
5 Clip, Flasher BRK-51850 1
6 Bracket Latch T-Handle FAS-24387A 1
7 Junction Panel Assembly HSG-51848 1
8 Relay 70 Amp ELC-24270 2
9 50 Amp Current Breaker ELC-24184 1
10 10 Lug Connector Cinch ELC-24188 1
11 Cinch Connector 6 Lug ELC-24190 1
12 Screw Machine Rd. Hd. 8 – 32 X ¾” FAS-25814 6
Nut Hex 8 – 32 FAS-28552 6
13 Connector 20 Lug Barrier Strip ELC-24220 1
14 Socket, Relay ELC-81005 1
Model BC-2002/CRC Tandem Illustrated Parts List
7-50 March 31, 2002
Figure 7-15. Oil Cooler Assembly
Model BC-2002/CRC Tandem Illustrated Parts List
March 31, 2002 7-51
Fig Item Description Part No. Qty. 7-15 Oil Cooler Assembly RF
1 Oil Cooler PTM-53230 1
2 Hex Bolt 5/16” – 18 X 1” 18
Flat Washer 5/16” 36
Lock-Washer 5/16” 18
Nut Hex 5/16” – 18 18
3 Fan Electric, Oil Cooler ELC-53231 2
4 Hex Bolt ¼” – 20 X 1” 8
Lock-Washer ¼” 8
Nut Hex ¼” – 20 8
5 Cover HSG-53245 1
6 Hex Bolt 3/8” – 16 X 1 ¼” 2
Flat Washer 3/8” 4
Nut Lock 3/8” – 16 2
7 Shroud HSG-53244 1
8 Sensor / Pressure Check Port (Modified 90D32MB-32MJ)
FIT-53335 1
9 Pressure Check Port Only (Modified 90D32MB-32MJ) FIT-53336 1
10 Bracket Hinge / Base BRK-53246 2
Model BC-2002/CRC Tandem Illustrated Parts List
7-52 March 31, 2002
Blank Page
Model BC-2002/CRC Tandem Illustrated Parts List
7-53 Blank/7-54 March 31, 2002
Figure 7-16. Pedestal and Control Box Assembly
Model BC-2002/CRC Tandem Illustrated Parts List
March 31, 2002 7-55
Fig Item Description Part No. Qty. 7-16 Pedestal and Control Box Assembly RF
1 Cable Assembly PTM-51634 1
2 Clevis (1/4” Pin) FAS-51635 1
3 Clevis (5/16” Pin) FAS-51758 1
4 Control Positive Lock MCH-51633 1
5 Valve Brake Control VLV-51640 1
6 Hex Bolt 5/16” – 18 X 1” FAS-28716 2
Lock-Washer 5/16” FAS-28646 2
Nut Hex 5/16” – 18 FAS-28501 2
7 Start Up Cable with Tee Handle & Clevis PTM-60980 1
8 Break Away Switch ELC-24281 1
9 Hex Bolt ¼” – 20 X ½” FAS-28700 4
10 Clamp, Cable FAS-60982 1
11 Parking Brake Knob MSC-51829 1
12 Security Box Assembly HSG-51697 1
13 CRC Display MTR-51753 1
14 Hex Bolt ¼” – 20 X ½” FAS-28714 2
15 Wiring Console Assembly SCH-51510 1
16 Hex Bolt 5/16” – 18 X ¾” FAS-28715 4
Lock-Washer 5/16” FAS-28646 4
Nut Hex 5/16” – 18 FAS-28501 4
17 Foot Pedal Brake Valve BRK-51240 1
18 Hex Bolt 5/16” – 18 X 1” FAS-28716 5
Lock-Washer 5/16” FAS-28646 5
Nut Hex 5/16” – 18 FAS-28501 5
19 Foot Switch, Varior Potentiometer (2000 – 2001) ELC-51832 1
Foot Pedal, Digital (2002) ELC-51836 1
20 Hex Bolt 5/16” – 18 X 1 ¼” FAS-28717 4
Flat Washer 5/16” FAS-28633 4
Lock-Washer 5/16” FAS-28646 4
Nut Hex 5/16” – 18 FAS-28501 4
21 Earphone ELC-60638 1
22 CB, 40 Channel ELC-60636 1
23 Antenna 39 ½” Height Magnetic Base ELC-60637 1
24 Ground Strap 12” ELC-24011 1
25 Nut Hex 3/8” – 16 FAS-28502 1
Flat Washer 3/8” FAS-28634 2
26 Pedestal Assembly, Tandem HSG-53373 1
Model BC-2002/CRC Tandem Illustrated Parts List
7-56 March 31, 2002
Figure 7-17. Hitch Assembly
Model BC-2002/CRC Tandem Illustrated Parts List
March 31, 2002 7-57
Fig Item Description Part No. Qty. 7-17 Hitch Assembly RF
1 Chipper Hitch Pin BRK-60658 1
2 Chipper Hitch Cylinder CYL-60651 1
3 Hex Bolt 5/8” – 11 X 3” FAS-28781A 2
Lock-Washer 5/8” FAS-28650 2
Nut Hex 5/8” – 11 FAS-28505 2
4 Hitch Assembly Cylinder Bracket BRK-51505 2
5 Tee ½” Male Jic X ½” O-Ring X ½” Male Jic T8MJ-8MB-8MJ 2
6 ½” Female Jic Cap C8FJ 2
9 Hitch Pin FAS-51506 1
Cotter Pin ¼” X 2 ½” FAS-25944 1
10 Pin Assembly Hitch Cylinder FAS-60941 1
Cotter Pin 3/16” X 2” FAS-25935 1
11 Hitch Hook BRK-61501 1
12 Hitch Assembly MCH-51500 1
Model BC-2002/CRC Tandem Illustrated Parts List
7-58 March 31, 2002
Blank Page
Model BC-2002/CRC Tandem Illustrated Parts List
7-59 Blank/7-60 March 31, 2002
Figure 7-18. Hitch Lift
Model BC-2002/CRC Tandem Illustrated Parts List
January 31, 2004 7-61
Fig Item Description Part No. Qty. 7-18 Hitch Lift RF
1 Directional Control Valve, Closed Center VLV-51621 2
2 Strain Relief 2
3 Double Check Valve, Stack-Up VLV-51920 1
4 Manifold Assembly HSG-61500 1
5 Soc. Hd. Bolt 5/16” – 18 X 3” 2
Lock-Washer 5/16” 2
Nut Hex 5/16” – 18 2
6 Hex Bolt ¾” – 10 X 3” 1
Nut Lock ¾” – 10 1
7 Restrictor Fitting FIT-29980 2
8 Cylinder 1 ½” X 10” CYL-22300 1
9 Hex Bolt ¾” – 10 X 2 ½” 1
Nut Lock ¾” – 10 1
10 Snatch Block Assembly 2
Snatch Block PTM-52053 2
Spacer PTM-53323 2
Nut Inner Spacer 7/8” – 9 2
Hex Bolt ¾” – 10 X 3 ½” 2
Nut Lock ¾” – 10 2
11 Sling Cable Assembly PTM-53333 1
12 Spring Assembly MCH-51816 1
13 Hex Bolt ¾” – 10 X 3” 1
Nut Lock ¾” – 10 1
14 Flat Washer ¾” 4
15 Nut Hex 7/8” – 9 1
Nut Jam 7/8” – 9 1
16 Hose #4 X 146” Long PIP-51762 1
17 Hose #4 X 156” Long PIP-51760 1
Model BC-2002/CRC Tandem Illustrated Parts List
7-62 March 31, 2002
Figure 7-19. Hitch Manifold W/Out Lift Option
Model BC-2002/CRC Tandem Illustrated Parts List
January 31, 2004 7-63
7-19 Hitch Manifold W/Out Lift Option RF
1 Soc. Hd. Cap Screw 10 – 24 X 2 ¾” FAS-25459 4
2 Valve Sol. Dir. Control Closed Center VLV-51621 1
3 Double Check Stack-Up Valve VLV-51920 1
4 Soc. Hd. Cap Screw 10 – 24 X ½” FAS-25450 4
5 Cover, Hydraulic Manifold Closed Center HSG-27355 1
6 Manifold, 2-Station Parallel MSC-51621 1
7 90 ½” Male O-Ring X ½” Male Jic 90D8MB-8MJ 2
8 Plug ½” Male O-Ring P8MB 4
9 ½” Male O-Ring X ½” Male Jic 8MB-8MJ 2
Model BC-2002/CRC Tandem Illustrated Parts List
7-64 March 31, 2002
Figure 7-20. Hitch Manifold W/Lift Option
Model BC-2002/CRC Tandem Illustrated Parts List
January 31, 2004 7-65
Fig Item Description Part No. Qty. 7-20 Hitch Manifold W/Lift Option RF
1 Soc. Hd. Bolt 10 – 24 X 2 ¾” 8
2 Directional Control Valve, Closed Center VLV-51621 2
3 Double Check Valve, Stack-Up VLV-51920 2
4 Manifold, 2-Station Parallel MSC-51621 1
5 90 ½” Male O-Ring X ½” Male Jic 90D8MB-8MJ 2
6 Plug ½” Male O-Ring P8MB 2
7 ½” Male O-Ring X ¼” Male Jic 8MB-4MJ 2
8 ½” Male O-Ring X ½” Male Jic 8MB-8MJ 2
Model BC-2002/CRC Tandem Illustrated Parts List
7-66 March 31, 2002
Blank Page
Model BC-2002/CRC Tandem Illustrated Parts List
7-67 Blank/7-68 March 31, 2002
Figure 7-21. Chip Box, Tandem
Model BC-2002/CRC Tandem Illustrated Parts List
July 15, 2002 7-69
Fig Item Description Part No. Qty. 7-21 Chip Box, Tandem RF
1 Auger Motor PMP-51625 1
2 Shaft, Auger Motor End PTM-53105 1
3 Left-Hand Auger 14” PTM-53130 1
Right-Hand Auger 14” PTM-53131 1
4 Shaft, Auger Bearing End PTM-53106 1
5 Bearing Guard GRD-53212 1
6 Proximity Switch Assembly MTR-53213 1
7 Valve Box Assembly (See Figure 7-24 for Details)
HSG-53110 1
8 Spacer, Valve Box BRK-53272 2
9 Quick Coupler, Female FIT-60911 1
10 Quick Coupler, Male FIT-60912 1
11 Bracket, Tow Bar, Quick Disconnect BRK-53409 2
12 Support Track BRK-53112 1
13 Chain PTM-50834 1
14 Cover PTM-50835 1
15 Bore Coupling 2 7/16” PTM-50837 1
16 Modified Coupling PTM-53065 1
17 Bracket, Auger Mount BRK-53056 1
18 Air Tank TNK-53080 1
19 Grizzly GRD-53204 2
20 Runner, Bearing Load PTM-53010 4
21 Snap Ring FAS-53017 4
22 Scraper, Rock GRD-53279 4
23 Chip Box Weldment HSG-53010 1
24 Bearing 4-Bolt PTM-51905 1
25 Spacer, Bearing BRK-53057 1
26 Bearing Plate BRK-53020 1
27 Seal RNG-53068 2
28 Seal Support Bracket BRK-53071 9
29 Modified Seal Bracket BRK-53096 2
30 Gate Assembly 12” MCH-53050 10
31 Hydraulic Motor Gear Box PMP-53160 1
32 Retainer, Cam Motor BRK-53069 1
33 Gate Cylinder Assembly CYL-50919 10
34 Bushing BRK-50738 20
35 Hex Bolt ½” – 20 X 1 ¼” FAS-28911 20
Flat Washer 7/16” FAS-28635 20
36 Support Locator, Potentiometer BRK-53109 1
37 Potentiometer Assembly (See Figure 7-22 for Details)
ELC-53322 1
Model BC-2002/CRC Tandem Illustrated Parts List
7-70 July 15, 2002
Fig Item Description Part No. Qty. 7-21 38 Manifold Hydraulic, Return MSC-53358 1
39 Retainer, Hose Guide GRD-53374 1
40 Mount Cam/Gate MCH-53052 10
41 Hex Bolt ¾” – 10 X 5 ½” FAS-28997 10
Nut Lock ¾” – 10 FAS-28542 10
42 Hex Bolt ¾” – 10 X 3 ½” FAS-28954 10
Nut Lock ¾” – 10 FAS-28542 10
43 Nut Hex 7/16” – 14 FAS-28503 20
Lock-Washer 7/16” FAS-28648 20
44 Cam Stop BRK-53070 2
45 Gear Box Assembly (See Figure 7-23 for Details)
PTM-53377 1
46 Camshaft MCH-53075 1
47 Guard, Potentiometer Barrier Strip GRD-53127 1
Model BC-2002/CRC Tandem Illustrated Parts List
7-71 Blank/7-72 March 31, 2002
Figure 7-22. Potentiometer Assembly
Model BC-2002/CRC Tandem Illustrated Parts List
March 31, 2002 7-73
Fig Item Description Part No. Qty. 7-22 Potentiometer Assembly RF
1 Capacitor, Axial 100 MFD ELC-24551 1
2 Barrier Strip, 6-Gang ELC-24190 1
3 Potentiometer ELC-53128 1
4 Housing, Potentiometer MSC-53067 1
5 Coupling, Female Pot Drive PTM-53270 1
6 Set Screw, Half Dog Point 5/16” – 18 X 5/16” FAS-25629 1
7 Coupling, Male Pot Drive PTM-50972 1
8 Soc. Hd. Set Screw 8 – 32 X ¼” FAS-25619 1
9 O-Ring 1 3/8” I.D. RNG-20910 1
Model BC-2002/CRC Tandem Illustrated Parts List
7-74 March 31, 2002
Blank Page
Model BC-2002/CRC Tandem Illustrated Parts List
7-75 Blank/7-76 March 31, 2002
Figure 7-23. Gear Box Assembly
Model BC-2002/CRC Tandem Illustrated Parts List
January 31, 2004 7-77
Fig Item Description Part No. Qty. 7-23 Gear Box Assembly RF
1 Gear Box Housing HSG-50621 1
2 Face Gear Box Housing HSG-50622 1
3 Gear Box Thrust Bearing Matched Pairs
PTM-53462 2
4 Bearing Gear Box #LM11949 PTM-50845 1
5 Bearing #11910 Cup PTM-50846 1
6 Bearing Gear Box #48548 PTM-50847 1
7 Bearing #LM48510 Cup PTM-50848 1
9 Speedo Gear Large 19 Tooth PTM-50843 1
11 Shaft Worm Drive Gear Box PTM-50856 1
12 Helix Angle Worm #WGA-1G For PTM-53463 1
13 Motor Mount Gear Box BRK-50855 1
14 Gear, Split PTM-53461 1
15 Soc. Hd. Cap Screw 3/8” – 16 X 1 ¾” FAS-25489 4
16 Soc. Hd. Cap Screw 3/8” – 16 X 5 ½” FAS-25496 2
17 Soc. Hd. Cap Screw 5/16” – 18 X 1” FAS-25480 4
18 Dowel Pin ½” I.D. X ¾” FAS-25353 6
20 3/16” X 3/16” X 2” Key STL-30951 1
21 1/8” Male Grease Zerk 2MP-Z 1
22 Soc. Hd. Set Screw 10 – 24 X ½” FAS-25614 2
23 Soc. Hd. Cap Screw 3/8” – 16 X 4” FAS-25499 2
Model BC-2002/CRC Tandem Illustrated Parts List
7-78 March 31, 2002
Blank Page
Model BC-2002/CRC Tandem Illustrated Parts List
7-79 Blank/7-80 March 31, 2002
Figure 7-24. Valve Box Assembly
Model BC-2002/CRC Tandem Illustrated Parts List
January 31,2004 7-81
Fig Item Description Part No. Qty. 7-24 Valve Box Assembly RF
1 Hydraulic Valve Closed Center VLV-51621 1
2 Soc. Hd. Screw 10 – 24 X 2 ¾” FAS-25459 4
3 Pressure Reducing Valve VLV-51929 1
4 Male Pipe 8MB-4MJ 1
5 90 Male Pipe 90D8MB-4MJ 3
6 Manifold, Sub Plate VLV-51613 1
7 30 Amp Circuit Breaker ELC-24290 1
8 Screw 8 – 32 X ½” FAS-25813 2
Nut Hex 8 – 32 FAS-25856 2
9 Insulator ELC-50152 2
10 Brass Screw 10 – 24 X 1 ½” FAS-25845 1
Brass Flat Washer FAS-28616 2
Brass Jam Nut 10 – 24 FAS-28571 2
11 Switch, Mom – Off – Mom ELC-24274 1
12 Chrome Plug FIT-24219 2
13 Switch, On/Off Single Pole ELC-24275 10
14 Spacer BRK-53116 2
15 Hex Bolt 3/8” – 16 X ¾” FAS-28730 4
Lock-Washer 3/8” 4
16 Switch Panel HSG-53115 1
17 20 Lug Barrier Strip ELC-24220 1
18 Din Connector ELC-24416 10
19 Blank Cover C-7 MSM-50899 2
20 Soc. Hd. Plug 3/8” FIT-28297 1
21 Soc. Hd. Plug ¼” FIT-28296 4
22 Male Pipe 4MJ-4MP 20
23 Valve Assembly, 12 Station VLV-50917 10
24 Hex Bolt ¼” – 20 X ¾” FAS-28701 4
Nut Hex ¼” – 20 FAS-28500 4
25 Male Pipe 8MJ-6MP 1
26 End Plate Set VLV-50900 1
27 Connector Strain Relief ½” ELC-24420 1
Locknut FAS-24170 1
28 Modified Box HSG-53111 1
4 way Versa Valve VLV-50902 10
Valve to Manifold Gasket RNG-27266 12
Model BC-2002/CRC Tandem Illustrated Parts List
7-82 March 31, 2002
Blank Page
Model BC-2002/CRC Tandem Illustrated Parts List
7-83 Blank/7-84 March 31, 2002
Figure 7-25. Chip Box Extension
Model BC-2002/CRC Tandem Illustrated Parts List
March 31, 2002 7-85
Fig Item Description Part No. Qty. 7-25 Chip Box Extension RF
1 Seal 1’ RNG-54059 1
2 Hex Bolt 5/16” – 18 X 1 ¼” 2
Lock-Washer 5/16” 2
Nut Hex 5/16” – 18 2
3 Hex Bolt ¾” – 10 X 5 ½” 1
Nut Lock ¾” – 10 1
4 Cylinder CYL-50919 1
5 Camshaft 1’ MCH-54048 1
6 Riser, Seal Support BRK-21447 2
7 Nut Hex 7/16” – 14 2
Lock-Washer 7/16” 2
8 Gate Assembly 12” MCH-53030 1
9 Bushing BRK-50738 1
10 Hex Bolt ½” – 20 X 1 ¼” 1
Flat Washer 7/16” 2
11 Plate Base HSG-54058 1
12 Mount Cam/Gate MCH-53052 1
13 Hex Bolt ¾” – 10 X 3 ½” 1
Nut Lock ¾” – 10 1
14 Extension Weldment 1’ HSG-54049 1
Model BC-2002/CRC Tandem Illustrated Parts List
7-86 March 31, 2002
Figure 7-26. Tow Bar Assembly
Model BC-2002/CRC Tandem Illustrated Parts List
March 31, 2002 7-87
Fig Item Description Part No. Qty. 7-26 Tow Bar Assembly RF
1 Pintle Eye MSC-51961 1
2 Drop Leg Jack MSC-51960 1
3 Safety Chain Lift Cylinder Shoe BRK-60829 1
4 4” X 20” Stroke Hydraulic Cylinder CYL-51962 1
5 Tow Bar Cylinder Top & Bottom Pins BRK-60825 2
6 Bushing Hex ½” X ¼” FIT-28344 1
7 Tee ¼” Male Jic X ¼” Male Jic X ¼” Male Pipe T4MJ-4MJ-4MP 1
8 ¼” Male Jic X ¼” Male Pipe 4MJX4MP 1
9 Elbow Pipe Street ½” FIT-28238 1
10 Bushing Hex ½” X ¼” FIT-28344 1
11 Nipple ¼” X Close Sch. 80 FIT-28001 1
12 Lock Out Valve VLV-22319 1
13 90 ¼” Male Jic X ¼” Male Pipe 90D4MJ-4MP 1
14 Hydraulic Supply Line Assembly PIP-60844 1
15 3/8” Male O-Ring X ¼” Male Jic 6MB-4MJ 2
16 Quick Disconnect Male HP ¼” X 6 Mor FIT-29632 2
17 Wheel & Tire Assembly MSC-80087 2
Rim Assembly White Rim 16.5 X 6.75 Spoked 8-6.5 MSC-80126 2
Tire 9.50-16.5 10 Ply Radial MSC-80127-T 2
18 2” Tow Bar Chipper Pin BRK-60823 2
Clip Click Pin Spring Loaded FAS-60821 2
19 Spindle Assembly BRK-60832 2
20 Hub Assembly PTM-51964 2
21 Air Supply Line Assembly PIP-60842 2
22 Glad Hands ELC-22375 2
23 Trailer Cord Assembly Chipper Tow Bar ELC-60840 2
24 Plug Trailer 7-Cond. ELC-24246 2
25 Hydraulic Cylinder Shoe BRK-60787 1
26 Safety Chain Tow Bar BRK-60828 2
27 Swing Away Hitch Assembly MCH-60796 1
Model BC-2002/CRC Tandem Illustrated Parts List
7-88 March 31, 2002
Figure 7-27. Heat Exchanger
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-1
SECTION 8. DIAGRAMS
Model BC-2002/CRC Tandem Diagrams
8-2 March 31, 2002
Blank Page
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-3/8-4 Blank
Figure 8-1. Console Wiring Detail, Tandem (2000 – 2001)
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-5/8-6 Blank
Figure 8-2. Console Wiring Detail, Tandem (2002)
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-7/8-8 Blank
Figure 8-3. Junction Box Wiring Detail, Tandem (2000 – 2001)
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-9/8-10 Blank
Figure 8-4. Junction Box Wiring Detail, Tandem (2002)
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-11/8-12 Blank
Figure 8-5. Valve Box Wiring Detail, Tandem (2000 – 2001)
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-13/8-14 Blank
Figure 8-6 (Sheet 1). Valve Box Wiring Detail, Tandem (2002)
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-15/8-16 Blank
Figure 8–6 (Sheet 2). Valve Box Wiring Detail, Tandem (2002)
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-17/8-18 Blank
Figure 8-7. Slave Box Wiring Detail, Tandem (2000 – 2001)
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-19/8-20 Blank
Figure 8-8. Slave Box Wiring Detail, Tandem (2002)
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-21/8-22 Blank
Figure 8-9. Digital Foot Control Wiring Detail, Tandem (2002)
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-23/8-24 Blank
Figure 8-10. Engine Wiring Detail, Tandem
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-25/8-26 Blank
Figure 8-11. Lights Wiring Detail
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-27
Table 8-1. BC-2002/CRC Tandem Electrical Circuit
Wire No. Wire Size Wire Color Description
1 16 WT-BK-GN CB1 to JB1 (back-up alarm)
1 16 BU JB1 to BB10 (back-up alarm)
1 16 BU BB10 to back-up alarm
1 16 BU BB10 to back-up alarm
2 16 WT-BK-YL CB2 from left belt switch (middle term)
2 16 WT-BK-YL CB2 to JB2 (left conveyor)
2 16 YL JB2 to left conveyor solenoid
3 16 WT-BN CB3 from right belt switch (middle term)
3 16 WT-BN CB3 to JB3 (right conveyor)
3 16 GN JB3 to right conveyor solenoid
4 16 WT-SL CB4 from hitch switch (top term)
4 16 WT-SL CB4 to JB4 (hitch open)
4 16 WT JB4 to hitch control valve
5 16 WT-BK-SL CB5 from hitch switch (bottom term)
5 16 WT-BK-SL CB5 to JB5 (hitch closed)
5 16 BK JB5 to hitch control valve
6 16 WT-BU-BN CB6 from water temp gauge (S-term)
6 16 WT-BU-BN CB6 to JB6 (water temp)
6 14 YL JB6 to water temp sensor on engine
7 16 WT-OR CB7 from hydraulic oil temp gauge (S-term)
7 16 WT-OR CB7 to JB7 (hydraulic oil temp)
7 16 WT JB7 to hydraulic oil temp sensor
8 16 WT-BK CB8 from oil pressure gauge (S-term)
8 16 WT-BK CB8 to JB8 (engine oil pressure)
8 14 BU JB8 to engine oil pressure sensor
9 16 WT-BN-PU CB9 from fuel gauge (S-term)
9 16 WT-BN-PU CB9 to JB9 (fuel gauge)
9 16 OR JB9 to fuel gauge
10 16 RN-GN CB10 from circuit breaker
10 16 RN-GN Right term 30 A circuit breaker to right term 15 A circuit breaker
10 16 RD-GN CB10 to JB10 to #7 term of relay (jumper to #8, #1 relay)
10 14 RD Relay term #5 to fuel pump solenoid (jumper to term #4 relay)
11 16 RD-BK CB11 from tach (bottom left term)
11 16 RD-BK CB11 to JB11 (tach)
11 14 BK JB11 to tach (off alternator)
12 16 WT-BK-BU CB12 from horn switch (right term)
12 16 WT-BK-BU CB12 to JB12 (horn)
Model BC-2002/CRC Tandem Diagrams
8-28 March 31, 2002
Table 8-1. BC-2002/CRC Tandem Electrical Circuit
Wire No. Wire Size Wire Color Description
12 14 BN JB12 to RB (remote shift barrier strip) #1 term
13 16 WT-RD CB13 from beacon switch (top right term) to beacon switch (bottom right term)
13 16 WT-RD CB13 to JB13 (beacon)
13 14 WT JB13 to beacon light
14 16 WT-BK-OR CB14 temp light & buzzer
14 16 WT-BK-OR CB14 to JB14 to term #2 relay (WT-BN-RD) to over-temp lights on console
14 14 OR JB14 to sensor (on oil cooler)
15 12 RD CB15 to light switch and to gauge lights
15 12 RD CB15 to JB15 (work & tail lights)
15 16 BK JB15 to front work light
15 16 BK JB15 to right work light
15 16 BK JB15 to rear work light
15 14 BK JB15 to BB8
15 14 BK BB8 to left work light
15 Diode BB8 to BB9
15 14 BN BB9 to left tail light
15 14 BN BB9 to right tail light
16 12 RD-WT Ignition switch (start term) to relay (term #4 & #5) from relay term (#1 & #8) to CB16s
16 12 RD-WT CB16 to JB16 (starter solenoid)
16 12 RD-WT JB16 to starter solenoid
17 12 Y1 CB17 to ignition switch (battery term)
17 12 Y1 CB17 to JB17 (starter post main +12V)
17 10 RD JB17 to starter post (main +12V term)
17 8 RD Starter post to battery (+12V term)
17 8 RD Battery (+ term) to alternator (+12V term)
18 12 OR CB18 from ignition switch (acc term)
18 12 OR CB18 to JB18 (ignition acc)
18 12 RD JB18 to 15 A (battery term) breaker
18 12 RD (Aux term) 15 A breaker to JB19 to air dryer
19 14 RD JB18 to air brake switch
19 16 WT CB19 to #2 term potentiometer port #7 amplifier (input)
19 16 WT (from 3-cond.)
CB19 to digital foot pedal
20 16 RD CB20 to #3 term potentiometer port #6 amplifier (+8V reg)
21 16 WT CB21 to center term digital foot pedal
22 16 RD CB22 from forward and reverse switch (bottom middle term) to CB22
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-29
Table 8-1. BC-2002/CRC Tandem Electrical Circuit
Wire No. Wire Size Wire Color Description
22 16 RD CB22 to E.D.C. plug (on hydrostatic trans)
23 16 BK CB23 to forward and reverse switch (center term) to CB23
23 16 BK CB23 to E.D.C. plug (on hydrostatic trans)
24 16 WT-BK-OR CB24 to buzzer & water temperature light
24 16 WT-RD-OR CB24 to JB24
24 12 GN JB24 to hydraulic temperature sensor
25 16 BN CB24 to buzzer and oil light
25 14 BN CB24 to JB24
25 14 BN JB24 to oil sending sensor
26 16 PU CB26 to rear auger switch (bottom term auto)
26 16 PU CB26 to SB15 (in 19-cond. Cable from slave box on right-hand conveyor)
26 16 WT-SL SB15 to (rear) VB12 (19-cond.)
26 16 RD VB12 to rear auger proximity switch (2-cond.)
26 16 BN Proximity switch (rear) VB11 (2-cond.)
26 16 WT-OR VB11 to SB14 (19-cond.)
27 16 GN CB27 to rear auger switch (top term manual)
27 16 YL CB27 to SB23 (19-cond.)
27 16 YL SBA23 to rear auger solenoid valve (4-cond.)
28 16 SL CB28 to breaker (right-hand term)
28 16 SL CB28 to SB11 (19-cond.)
28 16 SL SB11 to valve box power relay ¼” term #86
28 16 BK ¼” term #85 valve box power relay to ground
29 16 YL CB29 to front auger switch (top term manual)
29 16 YL CB29 to SB24 (19-cond.)
29 16 YL SB24 to front auger solenoid valve (4-cond.)
30 16 BU CB30 to front auger switch (bottom term auto)
30 16 BU CB30 to SB12 (19-cond.)
30 16 WT-BK-YL SB12 (19-cond.) to VB11
30 16 RD VB11 to front auger proximity switch (2-cond.)
30 16 BN Proximity switch (front) VB12 (2-cond.)
30 16 WT VB12 to SB13 (19-cond.)
31 16 WT-BK-GN CB31 to amplifier port #4 (valve +) to forward/reverse switch
31 16 PU Top center term to bottom lower term of switch
32 12 RD CB32 to master switch (top left-hand term) to master switch (top right-hand term)
32 12 RD CB32 to SB binding post (19-cond.)
32 12 RD SB32 binding post to 70 A relay 3/8” term valve box power
Model BC-2002/CRC Tandem Diagrams
8-30 March 31, 2002
Table 8-1. BC-2002/CRC Tandem Electrical Circuit
Wire No. Wire Size Wire Color Description
32 12 RD Valve box power relay 3/8” term to main binding power post
32 12 RD Computer power relay ¼” term and 3/8” term to SB binding post
32 14 RD From 3/8” term computer power relay to 12-pin connector slave L pin
32 12 RD From SB binding post to SB4 jumper SB4, SB3, SB2, jumper wire to SB13 jump to SB14, jumper wire to SB18 and jumper to SB19
32 8 RD SB main power binding post to 105 A breaker on engine
33 12 RD-WT CB33 to master switch (bottom right term) to master switch (bottom left term)
33 12 RD-WT CB33 to SB3, SB3 to rear 19-cond. And front 19-cond to VB rear 30 A breaker and VB front 30 A breaker
33 12 RD 30 A breaker to binding post of front VB and rear VB
33 16 RD All red wires from din connectors of air valves 1 thru 10 (front hopper) and 11 thru 20 (rear hopper) to binding posts in each valve box
33 16 RD VB1 to air solenoid valve #1
33 16 RD VB2 to air solenoid valve #2
33 16 RD VB3 to air solenoid valve #3
33 16 RD VB4 to air solenoid valve #4
33 16 RD VB5 to air solenoid valve #5
33 16 RD VB6 to air solenoid valve #6
33 16 RD VB7 to air solenoid valve #7
33 16 RD VB8 to air solenoid valve #8
33 16 RD VB9 to air solenoid valve #9
33 16 RD VB10 to air solenoid valve #10
33 16 RD VB11 to air solenoid valve #11
33 16 RD VB12 to air solenoid valve #12
33 16 RD VB13 to air solenoid valve #13
33 16 RD VB14 to air solenoid valve #14
33 16 RD VB15 to air solenoid valve #15
33 16 RD VB16 to air solenoid valve #16
33 16 RD VB17 to air solenoid valve #17
33 16 RD VB18 to air solenoid valve #18
33 16 RD VB19 to air solenoid valve #19
33 16 RD VB20 to air solenoid valve #20
34 16 BU CB34 from buzzer and air pressure light
34 16 BU CB34 to air pressure sending unit on throttle valve
35 16 WT CB35 to amplifier port #5 (valve –) to top right-hand term forward/reverse switch
35 10 WT-BK-RD Top right-hand term to bottom center terminal of forward/reverse switch
36 16 WT-BK-GN CB36 to right-hand belt switch (bottom term)
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-31
Table 8-1. BC-2002/CRC Tandem Electrical Circuit
Wire No. Wire Size Wire Color Description
36 16 WT-BK-GN CB36 to SB20 (19-cond.)
36 14 WT SB20 to right-hand (2-cond.) hopper diaphragm switch
37 16 RD CB37 to buzzer diode
38 16 WT-BK-YL CB38 to left-hand belt switch (bottom term)
38 16 WT-BK-YL CB38 to SB17 (19-cond.)
38 16 BN SB17 to left-hand (2-cond.) hopper diaphragm switch
39 – 40 CB39 – CB40 (for CB radio option)
41 16 BK (CB) ground to CRC (computer)
42 SHLD (CB) ground to CRC (computer)
44 16 GN (CB) forward and reverse switch from diodes to (CB) relay (term #7)
45 12 RD (CB) breaker (left term) to beacon switch (middle left term) to beacon switch (middle right term)
46 10 RD (CB) breaker (right term) to ignition switch (+12V term)
47 12 RD (CB) breaker (left term) to voltmeter (+ term)
47 16 RD (CB) voltmeter (+ term) to oil pressure gauge (+ term) to fuel gauge (+ term) to tachometer (+ term) to water temperature gauge (+ term) to hydraulic oil temp gauge (+ term)
48 16 BK (CB) ground to relay (term #2) to all lights & gauges & potentiometer
49 16 RD (CB) low-lock switch (middle term) to beacon switch (middle right term) to left belt switch (top term) to hitch switch (middle term) to right belt switch (top term) to hopper shift (middle term) both, front, & rear switches
50 16 RD (CB) horn switch (left term) to left term 15 Amp circuit breaker to warning gauge light terminals (+ side)
51 16 BU (CB) light switch (middle left term) to all gauge lights
52 8 RD JB17 to breaker (battery term)
52 12 RD Out breaker (aux. Term) to relays #1 & #2 (#30 term) out
52 16 BU Relay #1 (#87 term) to JB27
52 16 BU JB27 to fan #1
52 16 BU Relay #2 (#87 term) to JB28
52 16 BU JB28 to fan #2
53 16 RD JB18 to JB30 (acc to relay to sensor)
53 16 RD JB30 to relay #1 jump to relay #2 (#86 term)
53 16 OR Out relay #2 (#85 term) jump to relay #1 (#85 term) to JB26
53 16 OR JB26 to temperature switch on hydraulic return manifold
54 16 YL Turn signal switch to JB22
54 16 YL JB22 to flasher
54 16 RD Out flasher to JB29
54 16 RD JB29 to breaker (aux. Term)
55 16 BK Turn signal switch to JB23 (ground)
Model BC-2002/CRC Tandem Diagrams
8-32 March 31, 2002
Table 8-1. BC-2002/CRC Tandem Electrical Circuit
Wire No. Wire Size Wire Color Description
55 16 BK JB23 to stop light switch
55 16 RD Light switch to JB18
56 SLAVE
57 – 59 JB24-JB25 (SPARE)
60 16 BK BB1 from ground
60 16 WT BB1 to female trailer light socket (ground)
61 16 YL BB5 to female trailer light socket (optional)
62 16 GN BB7 to female trailer light socket (optional)
63 16 BN BB9 to female trailer light socket (optional)
64 16 BU Turn signal switch to BB2
64 16 YL BB2 to left front turn signal
65 16 GN Turn signal switch to BB3
65 16 GN BB3 to right front turn signal
66 16 YL Turn signal switch to BB4
66 Diode BB4 to BB5
66 16 GN BB5 to left rear turn signal
67 16 BN Turn signal switch to BB6
67 Diode BB6 to BB7
67 16 GN BB7 to right rear turn signal
68 12 RD Ground screw in VB to ground screw in SB (rear 19-cond.)
68 16 BK Ground screw in VB to rear cam switch (center term)
68 16 BK Cam switch (center term) to gate switch (center term)
68 16 BK Jumper wires from center term of all gate switches (rear VB)
69 12 RD Ground screw in VB to ground screw in SB (front 19-cond.)
69 16 BK Ground screw in VB to front cam switch (center term)
69 16 BK Cam switch (center term) to gate switch (center term)
69 16 BK Jumper wires from center term of all gate switches (front VB)
70 – 76 SPARE
77 16 BN Right-hand VB10 from computer slave SL-20
77 16 BK Right-hand VB10 to air solenoid valve #20
77 16 BK Right-hand VB10 to switch #20 (bottom term)
78 16 BN Right-hand VB9 from computer slave SL-19
78 16 BK Right-hand VB9 to air solenoid valve #19
78 16 BN Right-hand VB9 to switch #19 (bottom term)
79 16 BU Right-hand VB8 from computer slave SL-18
79 16 BK Right-hand VB8 to air solenoid valve #18
79 16 BU Right-hand VB8 to switch #18 (bottom term)
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-33
Table 8-1. BC-2002/CRC Tandem Electrical Circuit
Wire No. Wire Size Wire Color Description
80 16 GN Right-hand VB7 from computer slave SL-17
80 16 BK Right-hand VB7 to air solenoid valve #17
80 16 GN Right-hand VB7 to switch #17 (bottom term)
81 16 PU Right-hand VB6 from computer slave SL-16
81 16 BK Right-hand VB6 to air solenoid valve #16
81 16 PU Right-hand VB6 to switch #16 (bottom term)
82 16 SL Right-hand VB5 from computer slave SL-15
82 16 BK Right-hand VB5 to air solenoid valve #15
82 16 SL Right-hand VB5 to switch #15 (bottom term)
83 16 YL Right-hand VB4 from computer slave SL-14
83 16 BK Right-hand VB4 to air solenoid valve #14
83 16 YL Right-hand VB4 to switch #14 (bottom term)
84 16 WT-BK Right-hand VB3 from computer slave SL-13
84 16 BK Right-hand VB3 to air solenoid valve #13
84 16 WT-BK Right-hand VB3 to switch #13 (bottom term)
85 16 WT-BN Right-hand VB2 from computer slave SL-12
85 16 BK Right-hand VB2 to air solenoid valve #12
85 16 WT-BN Right-hand VB2 to switch #12 (bottom term)
86 16 WT-BK-GN Right-hand VB1 from computer slave SL-11
86 16 BK Right-hand VB1 to air solenoid valve #11
86 16 WT-BK-GN Right-hand VB1 to switch #11 (bottom term)
87 16 WT-BK-GN Left-hand VB1 from computer slave SL-10
87 16 BK Left-hand VB1 to air solenoid valve #10
87 16 WT-BK-GN Left-hand VB1 to switch #10 (bottom term)
88 16 WT-BN Left-hand VB2 from computer slave SL-9
88 16 BK Left-hand VB2 to air solenoid valve #9
88 16 WT-BN Left-hand VB2 to switch #9 (bottom term)
89 16 WT-BK Left-hand VB3 from computer slave SL-8
89 16 BK Left-hand VB3 to air solenoid valve #8
89 16 WT-BK Left-hand VB3 to switch #8 (bottom term)
90 16 YL Left-hand VB4 from computer slave SL-7
90 16 BK Left-hand VB4 to air solenoid valve #7
90 16 OR Left-hand VB4 to switch #7 (bottom term)
91 16 SL Left-hand VB5 from computer slave SL-6
91 16 BK Left-hand VB5 to air solenoid valve #6
91 16 SL Left-hand VB5 to switch #6 (bottom term)
92 16 PU Left-hand VB6 from computer slave SL-5
Model BC-2002/CRC Tandem Diagrams
8-34 March 31, 2002
Table 8-1. BC-2002/CRC Tandem Electrical Circuit
Wire No. Wire Size Wire Color Description
92 16 BK Left-hand VB6 to air solenoid valve #5
92 16 PU Left-hand VB6 to switch #5 (bottom term)
93 16 GN Left-hand VB7 from computer slave SL-4
93 16 BK Left-hand VB7 to air solenoid valve #4
93 16 GN Left-hand VB7 to switch #4 (bottom term)
94 16 BU Left-hand VB8 from computer slave SL-3
94 16 BK Left-hand VB8 to air solenoid valve #3
94 16 BU Left-hand VB8 to switch #3 (bottom term)
95 16 BN Left-hand VB9 from computer slave SL-2
95 16 BK Left-hand VB9 to air solenoid valve #2
95 16 BN Left-hand VB9 to switch #2 (bottom term)
96 16 BK Left-hand VB10 from computer slave SL-1
96 16 BK Left-hand VB10 to air solenoid valve #1
96 16 BK Left-hand VB10 to switch #1 (bottom term)
97 16 WT-BK-BU VB16 from computer slave pin #26 (right-hand 19-cond.)
97 16 WT-BK-BU VB16 to rear cam switch (bottom Term) (right-hand 19-cond.)
97 16 BK VB16 to hydraulic cam valve right-hand coil (right-hand VB)
98 16 WT-BK-OR VB15 from computer slave pin #25 (right-hand 19-cond.)
98 16 WT-BK-OR VB15 to right-hand cam switch (top term) (right-hand 19-cond.)
98 16 BK VB15 to hydraulic cam valve left-hand coil (right-hand VB)
99 16 WT-BK-BU VB16 from computer slave pin #24 (left-hand 19-cond.)
99 16 WT-BK-BU VB16 to left-hand cam switch (top term) (left-hand 19-cond.)
99 16 BK VB16 to hydraulic cam valve right-hand coil (left-hand VB)
100 16 WT-BK-OR VB15 from computer slave pin #23
100 16 WT-BK-OR VB15 to left-hand cam switch (bottom term)
100 16 BK VB15 to hydraulic cam valve left-hand coil (front VB)
101 16 WT-RD SB3 (left-hand 19-cond.) to front VB18 to right-hand hydraulic coil
101 16 WT-RD To jumper to VB13 to left-hand hydraulic coil
102 16 WT-RD SB3 (right-hand 19-cond.) to rear VB18 to right-hand hydraulic coil
102 16 WT-RD To jumper to VB13 to left-hand hydraulic coil
103 14 BK SB power 70 A relay ¼” connector to L port slave
104 16 UNSHD & BK SB from computer slave (off gray 3-wire) (J port)
104 16 UNSHD & BK To FPM sensor
105 16 WT SB from computer slave (off gray 3-wire) (G port)
105 16 WT To FPM sensor
106 16 RD SB from computer slave (off gray 3-wire) (A port)
106 16 RD To 5 A fuse to FPM sensor
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-35
Table 8-1. BC-2002/CRC Tandem Electrical Circuit
Wire No. Wire Size Wire Color Description
107 16 UNSHD & BK SB from computer slave (off gray 3-wire) (E port)
107 16 UNSHD & BK To rear barrier strip on hopper to potentiometer right term
108 16 RD SB from computer slave (off gray 3-wire) (F port)
108 16 RD To rear barrier strip on hopper to potentiometer left term
109 16 WT SB from computer slave (off gray 3-wire) (C port)
109 16 WT To rear barrier strip on hopper to potentiometer middle term
110 16 UNSHD & BK SB from computer slave (off gray 3-wire) (E port)
110 16 UNSHD & BK To front barrier strip on hopper to potentiometer right term
111 16 WT SB from computer slave (off gray 3-wire) (D port)
111 16 WT To front barrier strip on hopper to potentiometer left term
112 16 RD SB from computer slave (off gray 3-wire) (F port)
112 16 RD To front barrier strip on hopper to potentiometer middle term
113 – 120 SPARE
121 Diode From left-hand term on both hopper switches to right-hand term on front hopper switch and left-hand term on rear hopper switch
121 Diode From right-hand term on both hopper switches to right-hand term on front hopper switch and left-hand term on rear hopper switch
122 16 WT-BK From left-hand term of front hopper switch to CB122
122 16 WT-BK CB122 (cab 19-cond.) to SB8 to front control box
122 16 RD Front hopper switch in control box (4-cond.)
122 16 BK From left-hand term of front hopper switch to top left-hand term hydraulic valve coil
123 16 WT-OR From left-hand of front hopper switch to CB123
123 16 WT-OR CB123 (cab 19-cond.) to SB9 to front control box
123 16 WT Front hopper switch in control box (4-cond.)
123 16 WT From right-hand term of front hopper switch to top right-hand term hydraulic valve coil
124 16 WT-SL From right-hand term of rear hopper switch to CB124
124 16 WT-SL CB124 (cab 19-cond.) to SB10 to front control box
124 16 BK Rear hopper switch in control box (4-cond.)
124 16 RD From right-hand term of rear hopper switch to bottom left-hand term hydraulic valve coil
125 16 WT-RD From right-hand term of rear hopper switch to CB125
125 16 WT-RD CB125 (19-cond.) to SB1 to front control box
125 16 GN Rear hopper switch in control box (4-cond.)
125 16 BN From left-hand term of rear hopper switch to bottom right-hand term hydraulic valve coil
126 16 YL From bottom term hitch raise switch to CB126
126 16 YL CB126 to JB126 aux. Barrier strip to top hitch hydraulic valve coil
127 16 GN From top term hitch raise switch to CB127
Model BC-2002/CRC Tandem Diagrams
8-36 March 31, 2002
Table 8-1. BC-2002/CRC Tandem Electrical Circuit
Wire No. Wire Size Wire Color Description
127 16 GN CB126 to JB126 aux. Barrier strip to bottom hitch hydraulic valve coil
128 16 RD From bottom term low-lock switch to CB128 aux. Barrier strip
128 16 RD CB128 aux. Barrier strip to (2-cond.) low-lock valve on trans
129 16 RD Neutral light to CB129 aux. Barrier strip to low-lock switch
129 16 BK From low-lock valve to ground on CB aux. Barrier strip
129 16 BK From low-lock switch to ground on CB aux. Barrier strip
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-37/8-38 Blank
Figure 8-12. Air System Hose and Fitting Diagram, 2-Wheel Drive
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-39
Table 8-2. Air System Hose and Fittings, 2-Wheel Drive
Hose No. Hose Type Length Fitting Hose Description
1 H10408 124” 8U-8FJX, 2 Ea. From Regulator on Top Port of Air Tank (on Frame) to Chip Box Air Tank.
2 100R5.188 118” 4U-4FJX, 2 Ea. From 90D4MJ-4MP on End of Air Tank (on Frame) to Front Top 90D4MJ-2MPL on D-2 Governor.
3 H10408 55” 8U-8FJX 45D8U-8FJX
From 90D8MJ-8MP on Rear of Air Tank (on Frame) to Check Valve (comes with Air Dryer) on Wet Tank Right-Hand side.
4 100R5.188 34” 4U-4FJX, 2 Ea. From 90D4MJ-4MP on top of Compressor (on Cummins Engine) to Tee on Front of D-2 Governor.
5 S-10TW 68” 8E4-8FJX, 2 Ea. From Compressor (Supply S/S Hose) to Top Port of E-Con Valve (comes with Air Dryer).
6 H10408 115” 8U-8FJX, 2 Ea. From Air Tank (on Frame) to Right-Hand Front 8MJ-8MP on Treadle Valve.
7 1/8” SYNFLEX
24” NONE From 90D 10-32 Push-Lock to bottom on Air to Gauge in Console.
8 SPARE
9 100R5.188 50” 4U-4FJX, 2 Ea. From Tee on Left-Hand Front Port of Shuttle Valve (with Low Pressure Switch) to IN Port of 3-Way Mack Valve.
10 100R5.188 97” 4U-4FJX, 2 Ea. From 3-Way Mack Valve OUT Port to Air Horn.
11 H10408 56” 8U-8FJX, 2 Ea. From 90D8MJ-8MP Top Right-Hand Port of Treadle Valve to Right-Hand Port of Stop Light Switch.
12 SPARE
13 100R5.188 36” 4U-4FJX, 2 Ea. From 90D4MJ-4MP on Right-Hand Lower Port of Treadle Valve to 90D4MJ-2MP on Front Center Port of Emergency Brake Control.
14 SPARE
15 H10408 56” 8U-8FJX, 2 Ea. From 90D8MJ-4MP Top Port of 45# Fixed Regulator to Tee on Bottom Port of Double Check Valve Brake Switch.
16 H10408 40” 8U-8FJX, 2 Ea. From Left-Hand Port of Double Check Valve Brake Switch to 8MJ-4MP Forward Glad Hand.
17 100R5.188 90” 4U-4FJX, 2 Ea. From 90D4MJ-4MP on Right-Hand Rear Port of Tee on Quick Release Valve.
18 100R5.188 11 ½” 4U-4FJX, 2 Ea. From Lower Port of 3-Way Ball Valve to 4MJ-4MP of Glad Hand.
19 H10408 52” 8U-8FJX, 2 Ea. From Tee on Bottom Port of Double Check Valve Brake Switch to Middle Port of Left-Hand Quick Release Valve.
20 100R5.188 116” 4U-4FJX, 2 Ea. From Center Port of 3-Way Ball Valve to Center Port of Right-Hand Quick Release Valve.
21 H10408 26” 8U-8FJX, 2 Ea. From Front Port of Quick Release Valve to Forward Port of Right-Hand Air Brake Chamber.
22 H10408 34” 8U-8FJX, 2 Ea. From Rear Port of Right-Hand Quick Release Valve to Forward Port of Left-Hand Air Brake Chamber.
23 H10408 34” 8U-8FJX, 2 Ea. From Right-Hand Rear Port on Right-Hand Air Brake Chamber to Rear Port of Left-Hand Quick Release Valve.
24 H10408 26” 8U-8JFX, 2 Ea. From Front Port of Left-Hand Quick Release Valve to Rear Port of Left-Hand Air Brake Chamber.
Model BC-2002/CRC Tandem Diagrams
8-40 March 31, 2002
Table 8-2. Air System Hose and Fittings, 2-Wheel Drive
Hose No. Hose Type Length Fitting Hose Description
25 H10408 15” 8U-8FJX, 2 Ea. From Front Port of Quick Release Valve (with 45# Regulator) to Front Port of Air Can on Master Cylinder.
26 SPARE
27 H10408 75” 8U-8FJX, 2 Ea. From Quick Release Valve to Top Port of Air Can on Parking Disc Brake.
28 SPARE
29 100R5.188 10 ½” 4U-4FJX, 2 Ea. From Tee on Bottom of D-2 Governor to Air Dryer Left-Hand Port.
30 H10408 30” 8U-8FJX, 2 Ea. From 90D8MJ-8MP on Right-Hand Front of Air Dryer to 90D8MJ-8MP on Top Left-Hand Port of Wet Tank.
31 100R5.188 17” 4U-4FJX, 2 Ea. From 90D4MJ-4MP (Fitting Comes with E-Con Valve, has Built-In Check Valve) on Bottom Port of E-Con Valve to Top Outside 4MJ-2MP Port of D-2 Governor.
32 100R5.188 19” 4U-4FJX & 90D4E-4FJX
From 90D4MJ-4MP Front Center Port of E-Con Valve to Lower Outside Port 4MJ-2MP on D-2 Governor.
33 100R5.188 24” 4U-4FJX, 2 Ea. From Front Port of Tee on Quick Release Valve to Upper Port of 3-Way Ball Valve.
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-41/8-42 Blank
Figure 8-13. Air System Hose and Fitting Diagram, 4-Wheel Drive
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-43
Table 8-3. Air System Hose and Fittings, 4-Wheel Drive
Hose No. Hose Type Length Fitting Hose Description
1 H10408 124” 8U-8FJX, 2 Ea. From Regulator on Top Port of Air Tank (on Frame) to Chip Box Air Tank.
2 100R5.188 118” 4U-4FJX, 2 Ea. From 90D4MJ-4MP on End of Air Tank (on Frame) to Front Top 90D4MJ-2MPL on D-2 Governor.
3 H10408 55” 8U-8FJX & 45D8U-8FJX
From 90D8MJ-8MP on Rear of Air Tank (on Frame) to Check Valve (comes with Air Dryer) on Wet Tank Right-Hand Side.
4 100R5.188 34” 4U-4FJX, 2 Ea. From 90D4MJ-4MP on Top of Compressor (on Cummins Engine) to Tee on Front of D-2 Governor.
5 S-10TW 68” 8E4-8FJX, 2 Ea. From Compressor (Supply S/S Hose) to Top Port of E-Con Valve (comes with Air Dryer).
6 H10408 115” 8U-8FJX, 2 Ea. From Air Tank (on Frame) to Right-Hand Front 8MJ-8MP on Treadle Valve.
7 1/8” SYNFLEX
24” NONE From 90D 10-32 Push Lock Fitting to Bottom on Air Gauge in Console.
8 SPARE
9 100R5.188 50” 4U-4FJX, 2 Ea. From Tee on Left-Hand Front Port of Shuttle Valve (with Low Pressure Switch) to IN Port of 3-Way Mack Valve.
10 100R5.188 97” 4U-4FJX, 2 Ea. From 3-Way Mack Valve OUT Port to Air Horn.
11 H10408 56” 8U-8FJX, 2 Ea. From 90D8MJ-8MP Top Right-Hand Port of Treadle Valve to Top Port 45# Regulator.
12 SPARE
13 100R5.188 36” 4U-4FJX, 2 Ea. From 90D4MJ-4MP on Right-Hand Lower Port of Treadle Valve to 90D4MJ-2MP on Front Center Port of Emergency Brake Control.
14 SPARE
15 SPARE
16 SPARE
17 100R5.188 90” 4U-4FJX, 2 Ea. From 90D4MJ-4MP on Right-Hand Rear Port of Emergency Brake Control Valve to Upper Port of Quick Release Valve Front Parking Disc Brake.
18 SPARE
19 SPARE
20 SPARE
21 SPARE
24 SPARE
25 H10408 15” 8U-8FJX, 2 Ea. From Front Port of Quick Release Valve (with 45# Regulator) to Front Port of Air Can Master Cylinder.
26 H10408 40” 8U-8FJX, 2 Ea. From Right-Hand Port of Quick Release Port to Front Port of Air Can on Master Cylinder.
27 H10408 75” 8U-8FJX, 2 Ea. From Quick Release Valve to Top Port of Air Can on Parking Disc Brake.
28 SPARE
29 100R5.188 10 ½” 4U-4FJX, 2 Ea. From Tee on Bottom of D-2 Governor to Air Dryer Left-Hand Port.
Model BC-2002/CRC Tandem Diagrams
8-44 March 31, 2002
Table 8-3. Air System Hose and Fittings, 4-Wheel Drive
Hose No. Hose Type Length Fitting Hose Description
30 H10408 30” 8U-8FJX, 2 Ea. From 90D8MJ-8MP on Right-Hand Front of Air Dryer to 90D8MJ-8MP on Top Left-Hand Port of Wet Tank.
31 100R.188 17” 4U-4FJX, 2 Ea. From 90D4MJ-4MP (Fitting Comes with E-Con Valve, has Built in Check Valve) on Bottom Port of E-Con Valve to Top Outside 4MJ-2MP Port of D-2 Governor.
32 100R5.188 19” 4U-4FJX & 90D4E-4FJX
From 90D4MJ-4MP Front Center Port of E-Con Valve of Lower Outside Port 4MJ-2MP on D-2 Governor.
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-45
Table 8-4. Air System Parts and Fittings Chart
Item No. Description Part Number Qty
A Nipple ¼” X Close FIT-28001 3
B Nipple ¼” X 1 ½” FIT-28012 1
C Bushing Hex ¾” X ¼” FIT-28346 1
D Bushing Hex ½” X ¼” FIT-28344 3
E 90 Pipe Straight Elbow ¼” FIT-28236 1
F Valve Ball ¼” VLV-29195 2
G ¼” Male Jic X ¼” Male Pipe 4MJ-4MP 1
H 90 ¼” Male Jic X ¼” Male Pipe 90D4MJ-4MP 7
I ¼” Male Jic X 1/8” Male Pipe 4MJ-2MP 2
J 90 ¼” Male Jic X 3/8” Male Pipe 90D4MJ-6MP 1
K 90 ¼” Male Jic X 1/8” Male Pipe 90D4MJ-2MP 4
L Tee ¼” Male Jic X ¼” Male Pipe X ¼” Male Jic T4MJ-2MP-4MJ 1
M ½” Male Jic X ¼” Male Pipe 8MJ-4MP 2
N 90 ½” Male Jic X ¼” Male Pipe 90D8MJ-4MP 5
O 3/8” Female Pipe X ½” Male Jic 6FP-8MP 1
P ½” Male Jic X 3/8” Male Pipe 8MJ-6MP 6
Q 90 ½” Male Jic X 3/8” Male Pipe 90D8MJ-6MP 2
R Tee ½” Male Jic 3/8” Male Pipe X ½” Male Jic T8MJ-6MP-8MJ 1
S ½” Male Jic ½” Male Pipe 8MJ-8MP 2
T ½” Male Jic X ¾” Male Pipe 8MJ-12MP 1
U 90 ½” Male Jic X ½” Male Pipe 90D8MJ-8MP 6
V 90 ½” Push Lock X 10-32 Thread 90D2PL-10-32M 1
W ½” MP X ¾” Bulk Head X ½” Male Pipe 8MP-12BH-8MP 2
X Glad Hand ELC-22370 2
Y 60 PSI Governor MTR-25255 1
Z Safety Relief Valve (150 PSI) VLV-51638 1
AA Air Tank Assembly Chassis TNK-51993 1
AB Cummins Engine Part Compressor 1
AC D-2 Governor VLV-51637 1
AD Wet Air Tank HSG-51437 1
AE E3 Brake Valve VLV-51639 1
AF Valve PP3 Brake Control VLV-51640 1
AG Valve S/S 3-Way Ball Valve VLV-29216 1
AH DS2 DB1 Check & Stop Light Switch VLV-51641 1
AI Comes With Air Dryer Pressure Controlled CK Valve 1
AJ Master/Cylinder Air/Hydraulic JD&SP/Dana (2-Ea if 4-Wheel Drive). PTM-51644 1
Model BC-2002/CRC Tandem Diagrams
8-46 March 31, 2002
Table 8-4. Air System Parts and Fittings Chart
Item No. Description Part Number Qty
AK Comes on Rear Axle Air Chamber Rear Brakes 2
AL QR-1 Quick Release Valve VLV-51642 3
AM Horn MSC-51645 1
AN Comes With Air Dryer E-Con Valve 1
AO Air Dryer Rockwell Wabco FTR-60949 1
AP Brake Parking Assembly PTM-53235 1
AQ SPARE
AR Regulator Air 45# Fixed ¼” NPT VLV-26201 1
AS Tee ¼” Female Pipe X ¼” Female Pipe X ¼” Male Pipe T4FP-4FP-4MP 1
AT 90 ¼” Male Jic X ¼” Male Pipe Long 90D4MJ-2MP-L 1
AU Modified (90D4MJ-2MP) Air Supply FIT-51998 1
AV Switch Low Air 65 PSI Control Grnd ELC-60309 1
AW Bushing Hex 3/8” X ¼” FIT-28342 1
AX Regulator Air 80# Fixed ¼” NPT VLV-26199 1
AY Gauge 1 ½” Dia (O-160) 1/8” NPT Control Port MTR-50665 1
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-47/8-48 Blank
Figure 8-14. Spread Hopper Gate Air System
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-49
Table 8-5. Air System Hose and Fittings, Spread Hopper Gates, Front and Rear
Hose No. (A & B) Hose Type Length Fitting Hose Description
1A or 20A 100R5.188 20” RS4, R4FJ, RN4FJX
From Bottom Port “A” on No. 1 and No. 20 Gate Cylinder to “A” Port Air Valve.
1B or 20B 100R5.188 18” RS4, R4FJ, RN4FJX
From Top Port “B” on No. 1 and No. 20 Gate Cylinder to “B” Port Air Valve.
2A or 19A 100R5.188 20” RS4, R4FJ, RN4FJX
From Bottom Port “A” on No. 2 and No. 19 Gate Cylinder to “A” Port Air Valve.
2B or 19B 100R5.188 18” RS4, R4FJ, RN4FJX
From Top Port “B” on No. 2 and No. 19 Gate Cylinder to “B” Port Air Valve.
3A or 18A 100R5.188 30 ½” RS4, R4FJ, RN4FJX
From Bottom Port “A” on No. 3 and No. 18 Gate Cylinder to “A” Port Air Valve.
3B or 18B 100R5.188 23 ½” RS4, R4FJ, RN4FJX
From Top Port “B” on No. 3 and No. 18 Gate Cylinder to “B” Port Air Valve.
4A or 17A 100R5.188 43” RS4, R4FJ, RN4FJX
From Bottom Port “A” on No. 4 and No. 17 Gate Cylinder to “A” Port Air Valve.
4B or 17B 100R5.188 34 ½” RS4, R4FJ, RN4FJX
From Top Port “B” on No. 4 and No. 17 Gate Cylinder to “B” Port Air Valve.
5A or 16A 100R5.188 53 ½” RS4, R4FJ, RN4FJX
From Bottom Port “A” on No. 5 and No, 16 Gate Cylinder to “A” Port Air Valve.
5B or 16B 100R5.188 45” RS4, R4FJ, RN4FJX
From Top Port “B” on No. 5 and No. 16 Gate Cylinder to “B” Port Air Valve.
6A or 15A 100R5.188 71 ½” RS4, R4FJ, RN4FJX
From Bottom Port “A” on No, 6 and No. 15 Gate Cylinder to “A” Port Air Valve.
6B or 15B 100R5.188 58” RS4, R4FJ, RN4FJX
From Top Port “B” on No. 6 and No. 15 Gate Cylinder to “B” Port Air Valve.
7A or 14A 100R5.188 74” RS4, R4FJ, RN4FJX
From Bottom Port “A” on No. 7 and No. 14 Gate Cylinder to “A” Port Air Valve.
7B or 14B 100R5.188 68” RS4, R4FJ, RN4FJX
From Top Port “B” on No. 7 and No. 14 Gate Cylinder to “B” Port Air Valve.
8A or 13A 100R5.188 86” RS4, R4FJ, RN4FJX
From Bottom Port “A” on No, 8 and No. 13 Gate Cylinder to “A” Port Air Valve.
8B or 13B 100R5.188 77” RS4, R4FJ, RN4FJX
From Top Port “B” on No. 8 and No. 13 Gate Cylinder to “B” Port Air Valve.
9A or 12A 100R5.188 93” RS4, R4FJ, RN4FJX
From Bottom Port “A” on No. 9 and No. 12 Gate Cylinder to “A” Port Air Valve.
9B or 12B 100R5.188 88” RS4, R4FJ, RN4FJX
From Top Port “B” on No. 9 and No. 12 Gate Cylinder to “B” Port Air Valve.
10A or 11A 100R5.188 105 ½” RS4, R4FJ, RN4FJX
From Bottom Port “A” on No. 10 and No. 11 Gate Cylinder to “A” Port Air Valve.
10B or 11B 100R5.188 99” RS4, R4FJ, RN4FJX
From Top Port “B” on No. 10 and No. 11 Gate Cylinder to “B” Port Air Valve.
Air Supply H10408 104” 8U-8FJX, 90D8U-8FJX-L
From Air Tank on Hopper to Air Valve Assembly in Valve Box.
Model BC-2002/CRC Tandem Diagrams
8-50 March 31, 2002
Blank Page
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-51/8-52 Blank
Figure 8-15. Hydraulic/Misc. Hose and Fittings
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-53
Table 8-6. Hydraulic/Misc. Hose and Fittings
Item No. Hose Type Length Fitting Hose Description
1 H10408 118” 8U-8FJX, 2 Ea. From Diesel Tank Supply to IN Port Primary Fuel Filter on Frame.
2 H10408 50” 8U-8FJX, 2 Ea. From OUT Port of Primary Fuel Filter on Frame to Cummins Primary Fuel Filter.
3 5/16” Fuel Hose
160” 5PL-4MP & 90D5PL-4MP
Return Off Injector Pump to Fuel Tank.
4 H24504 98” 4U2-4FJX, 2 Ea. From Brake Master Cylinder to T4MJ-4MJ-MJ Tee on Left-Hand Brake on Drive Axle.
5 H24504 19 ½” 4U2-4FJX & 90D4U2-4FJX
From T4MJ-4MJ-4MJ Tee to Left-Hand Brake.
6 H24504 70” 4U2-4FJX & 90D4U2-4FJX
From T4MJ-4MJ-4MJ Tee to Right-Hand Brake.
7 H24504 39 ¼” 4U2-4FJX, 2 Ea. From 90D4MB-4MJ on Left Steering Valve (LS Port) to 6MB-4MJ on Shuttle Valve Port on Left Side.
8 H24504 26” 4U2-4FJX & 90D4U2-4FJX
From 90D4MB-4MJ (LS Port) of Priority Valve to Center Port of Shuttle Valve.
9 H24504 39 ¼” 4U2-4FJX, 2 Ea. From 90D4MB-4MJ Hand Steering Valve (LS Port) to 6MB-4MJ on Right-Hand Side of Shuttle Valve.
10 H10408 35 ½” 8U-8FJX, 2 Ea. From 8MB-8MJ Bottom Port on Steering Manifold Left-Hand Side to 8MB-8MJ (L Port) at Left-Hand Steering Valve.
11 H10408 35 ½” 8U-8FJX, 2 Ea. From 8MB-8MJ Top Part on Steering Manifold Left-Hand Side to 8MB-8MJ (T Port) of Left-Hand Steering Valve.
12 H10408 35 ½” 8U-8FJX, 2 Ea. From 8MB-8MJ 2nd Port From Top on Steering Manifold Left-Hand Side to (P Port) of Left-Hand Steering Valve.
13 H10408 35 ½” 8U-8FJX, 2 Ea. From 8MB-8MJ 3rd Port From Top on Steering Manifold Left-Hand Side to (R Port) of Left-Hand Steering Valve.
14 H10408 115” 8U-8FJX & 45D8U-8FJX
From 90D8MB-8MJ Front Bottom Left to T8MB-8MJ-8MJ Tee on Port of Rod End of Left-Hand Steering Cylinder.
15 H10408 31 ½” 8U-8FJX & 45D8U-8FJX
From T8MB-8MJ Tee on Left-Hand Steering Cylinder to 90D6MB-8MJ on Rear Port of Right-Hand Steering Cylinder.
16 H10408 31 ½” 8U-8FJX & 45D8U-8FJX
From T8MB-8MJ-8MJ Tee on Right-Hand Steering Cylinder to 90D6MB-8MJ on Rear Port of Left-Hand Steering Cylinder.
17 H10408 110” 8U-8FJX & 45D8U-8FJX
From 90D8MB-8MJ Front Bottom Right to T8MB-8MJ-8MJ Tee on Port of Rod End of Right-Hand Steering Cylinder.
18 H10408 35 ½” 8U-8FJX, 2 Ea. From 8MB-8MJ 3rd Port from Top on Steering Manifold Right-Hand Side to (R Port) of Steering Valve.
19 H10408 35 ½” 8U-8FJX, 2 Ea. From 8MB-8MJ 2nd Port from Top on Steering Manifold Right-Hand Side to (P Port) of Right-Hand Steering Valve.
20 H10408 35 ½” 8U-8FJX, 2 Ea. From 8MB-8MJ Bottom Port on Steering Manifold Right-Hand Side to 8MB-8MJ (L Port) of Right-Hand Steering Valve.
21 H10408 35 ½” 8U-8FJX, 2 Ea. From 8MB-8MJ Top Port on Steering Manifold Right-Hand Side to 8MB-8MJ (T Port) of Right-Hand Steering Valve.
22 H10408 12” 8U-8FJX, & 90D8U-8FJX
From 90D8MB-8MJ Center Left-Hand Port of Steering Manifold to 90D8MB-8MJ of ”CF” Port of Priority Valve.
23 H10408 77” 8U-8FJX, 2 Ea. From 90D8MB-8MJ Top Right-Hand Port of Steering Manifold to 90D8MB-8MJ 2nd Port on Top of Return Manifold.
Model BC-2002/CRC Tandem Diagrams
8-54 January 31, 2004
Table 8-6. Hydraulic/Misc. Hose and Fittings
Item No. Hose Type Length Fitting Hose Description
24 H10408 96” 8U-8FJX, 2 Ea. From 90D8MB-8MJ (B Port) of Hitch Manifold to T8MB-8MJ-8MJ Tee Rod End of Hitch Cylinder.
25 H10408 103 ½” 8U-8FJX, 2 Ea. From 8MB-8MJ (A Port) of Hitch Manifold to T8MB-8MJ-8MJ Tee Rear Port of Hitch Cylinder.
26 H10408 110” 8U-8FJX, 2 Ea. From (T Port) on Hitch Manifold to Top 1st Port Return Manifold.
27 H42508 185” 8U-8FJX & 90D8U-8FJX
From 90D8MB-8MJ on Right-Hand Port of Pressure Manifold to (P Port) of Hitch Manifold.
28 PiP-53310 41 ½” PURCHASED HOSE
From Left-Hand Port on Sunstrand Pump to Left Port of Sunstrand Motor.
29 H10412 36” 12U-12FJX, 2 Ea. Sunstrand Pump Case Bleed Port to Sunstrand Motor Top Case Bleed Port.
30 H10420 48” 20U-20FJX, 2 Ea. From Sunstrand Pump (Drive Pump) Suction Port to Left-Hand 2-Filter Assembly OUT Port.
31 H10420 29” 20U-20FJX, 2 Ea. From IN Port on 2-Filter Assembly to Left Shut Off Gate Valve on Hydraulic Tank.
32 H10416 60” 16U-16FJX, 2 Ea. From Suction Screen on Top of Hydraulic Tank to Front Port on Power Steering Pump on Engine.
33 H10412 32” 12U-16FJX & 12U-12FJX
From Compensator Valve on Belt Drive Pump to T12MP-12MJ-12MJ Tee on Hydraulic Tank.
34 SPARE
35 SPARE
36 H10412 18” 12U-12FJX, & 90D12U-12FJX
From Right-Hand Back Port of Belt Pump (Case Bleed) to Tee on Front Right-Hand Side Hydraulic Tank.
37 SPARE
38 H24504 90” 4U2-4FJX, 2 Ea. From T Port of Priority Valve to Top Front Port of Return Manifold.
39 SPARE
40 H10412 116” 12U-12FJX, 2 Ea. From Sunstrand Motor Case Bleed Port to Traction Filter Assembly on Hydraulic Tank.
41 PiP-53269 43” PURCHASED HOSE
From Right-Hand Port on Sunstrand Pump to Right-Hand Port on Sunstrand Motor.
42 H10408 110” 8U-8FJX, 2 Ea. From (T Port) on Chip Box Hydraulic Manifold to Center Top Return Manifold.
43 PiP-53328 111” PURCHASED HOSE
From Left-Hand Port of Oil Cooler to Rear Port of Return Hydraulic Manifold.
44 PiP-53327 130” PURCHASED HOSE
From Right-Hand Port of Oil Cooler to IN Port of 3-Filter Assembly.
45 SPARE
46 SPARE
47 H10420 23” 20U-20FJX, 2 Ea. From OUT Port of 3-Filter Assembly to Gate Valve on Hydraulic Tank.
48 SPARE
49 SPARE
50 H42508 15” 8U-8FJX, 2 Ea. From Top of Pressure Manifold to Front Pump Valve.
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-55
Table 8-6. Hydraulic/Misc. Hose and Fittings
Item No. Hose Type Length Fitting Hose Description
51 H10408 15” 8U-8FJX, 2 Ea. From Back Port of Pump Valve to 90D8MP-8MJ on Top of Hydraulic Tank.
52 2 ½” SUCTION HOSE
30 ½” NONE 5/8” BANDING
From Right-Hand Filter.
53 H42508 65” 8U-8FJX & 90D8U-8FJX-L
From Top Port of Steering Pump (on Engine) to 90D8MB-8MJ (P Port) on Priority Valve.
54 H10412 85” 12U-12FJX & 45D12-12FJX
From “EF” Port of Priority Valve to Bottom Front Port of Return Manifold.
55 H43012 127” 12E4-12FJX, 2 Ea. From Front Flow Regulator on Pressure Manifold (on Conveyor) to Left Belt Motor Pressure Port.
56 H43012 133” 12E4-12FJX, 2 Ea. From Rear Flow Regulator on Pressure Manifold (on Conveyor) to Right Belt Motor Pressure Port.
57 H24504 24” 4U2-4FJX, 2 Ea. Right-Hand Belt Motor Case Bleed to Center Return Manifold (on Conveyor).
58 H24504 30” 4U2-4FJX, 2 Ea. Left-Hand Belt Motor Case Bleed to Center Return Manifold (on Conveyor).
59 H10412 21 ½” 12U-12FJX, 2 Ea. Right-Hand Belt Motor Return to Center Manifold (on Conveyor).
60 H10412 22 ½” 12U-12FJX, 2 Ea. Left-Hand Belt Motor Return to Center Manifold (on Conveyor).
61 H10412 160” 12U-12FJX, 2 Ea. Return Manifold (Rear Hopper) to Center Return Manifold (on Conveyor).
62 H10412 195” 12U-12FJX, 2 Ea. Return Manifold (Front Hopper) to Center Return Manifold (on Conveyor).
63 H24504 109” 4U2-4FJX, 2 Ea. Hydraulic Valve Manifold (in Front Valve Box) Return to Return Manifold on Front Hopper.
64 H24504 109” 4U2-4FJX, 2 Ea. Hydraulic Valve Manifold (in Rear Valve Box) Return to Return Manifold on Rear Hopper.
65 H10408 27” 8U-8FJX, 2 Ea. Front Auger Motor Return Hose to Return Manifold (on Front Hopper).
66 H10408 27” 8U-8FJX, 2 Ea. Rear Auger Motor Return Hose to Return Manifold (on Rear Hopper).
67 H24504 30” 4U2-4FJX, 2 Ea. Rear Auger Motor Case Bleed to Return Manifold (on Rear Hopper).
68 H24504 30” 4U2-4FJX, 2 Ea. Front Auger Motor Case Bleed to Return Manifold (on Front Hopper).
69 H24504 276” 4U2-4FJX, 2 Ea. Pressure Hose From P Port on 2-Station Manifold (on Left-Hand Conveyor) to Front Valve Box Manifold.
70 H24504 265” 4U2-4FJX, 2 Ea. Pressure Hose From P Port on 2-Station Manifold (on Left-Hand Conveyor) to Rear Valve Box Manifold.
71 H24504 212” 4U2-4FJX, 2 Ea. Left-Hand 4-Port Lock-Out Valve to Rear Hopper Hydraulic Cylinder (Ram End of Cylinder).
72 H24504 139” 4U2-4FJX, 2 Ea. Left-Hand 4-Port Lock-Out Valve to Rear Hopper Hydraulic Cylinder (Housing End of Cylinder).
73 H24504 212” 4U2-4FJX, 2 Ea. Right-Hand 4-Port Lock-Out Valve to Front Hopper Hydraulic Cylinder (Ram End of Cylinder).
Model BC-2002/CRC Tandem Diagrams
8-56 January 31, 2004
Table 8-6. Hydraulic/Misc. Hose and Fittings
Item No. Hose Type Length Fitting Hose Description
74 H24504 139” 4U2-4FJX, 2 Ea. Right-Hand 4-Port Lock-Out Valve to Front Hopper Hydraulic Cylinder (Housing End of Cylinder).
75 H24504 25 ½” 4U2-4FJX, 2 Ea. Pressure Port on 2-Station Manifold (on Conveyor) to Left-Hand 4-Port Lock-Out Valve.
76 H24504 25 ½” 4U2-4FJX, 2 Ea. Pressure Port on 2-Station Manifold (on Conveyor) to Left-Hand 4-Port Lock-Out Valve.
77 H24504 29” 4U2-4FJX, 2 Ea. Pressure Port on 2-Station Manifold (on Conveyor) To Right-Hand 4-Port Lock-Out Valve.
78 H24504 29” 4U2-4FJX, 2 Ea. Pressure Port on 2-Station Manifold (on Conveyor) to Right-Hand 4-Port Lock-Out Valve.
79 H24508 223” 8U-8FJX, 2 Ea. Front Flow Control Valve (Right-Hand Conveyor) to Front Auger Motor (Pressure).
80 H24508 279” 8U-8FJX, 2 Ea. 2nd Flow Control Valve Right-Hand Conveyor (from Front) to Rear Auger Motor (Pressure).
81 H24504 59” 4U2-4FJX & 90D4U2-4FJX
From Port on Rear Valve Box Manifold to Port on Rear Cam Motor.
82 H24504 70” 4U2-4FJX & 90D4U2-4FJX
From Port on Rear Valve Box Manifold to Port on Rear Cam Motor.
83 H24504 59” 4U2-4FJX & 90D4U2-4FJX
From Port on Front Valve Box Manifold to Port on Front Cam Motor.
84 H24504 70” 4U2-4FJX & 90D4U2-4FJX
From Port on Front Valve Box Manifold to Port on Front Cam Motor.
85 H24508 42” 8U-8FJX & 90D8U-8FJX
Pressure From P Port (on Front Center Pressure Manifold) to P Port on 2-Station Manifold on Left-Hand Conveyor.
86 H24508 47” 8U-8MJ & 90D8U-8FJX-L
Return From T Port on 2-Station Manifold (Left-Hand Conveyor) to Return Manifold on Right-Hand Side Chipper Frame.
87 H24504 10” 4U2-4FJX, 2 Ea. From Port on Right-Hand Side Hydrostatic Pump to Right-Hand Port on Shuttle Valve.
88 H24504 10” 4U2-4FJX, 2 Ea. From Port on Left-Hand Side Hydrostatic Pump to Left-Hand Port on Shuttle Valve.
89 H24504 53” 4U2-4FJX, 2 Ea. From Port on Hydrostatic Motor EDC Valve to Center Port of Shuttle Valve.
90 4-WD
H24504 124” 4U2-4FJX & 90D4U2-4FJX
Pressure Hose From Master Cylinder to Brake Tee Center (Rear Axle).
91 4-WD
H24504 54” 4U2-4FJX & 90D4U2-4FJX
From Brake Tee (Left-Hand) to Rear Axle Left-Hand Brake.
92 4-WD
H24504 58” 4U2-4FJX & 90D4U2-4FJX
From Brake Tee to Rear Axle Right-Hand Brake.
93 H24504 146” 4U2-4FJX, 2 Ea. From Pressure Port 2-Station Manifold (Hitch) to Cylinder (Ram End) Hitch Raise Cylinder.
94 H24504 156” 4U2-4FJX, 2 Ea. From Pressure Port 2-Station Manifold (Hitch) to Cylinder (Housing End) Hitch Raise Cylinder.
95 H24504 31” 4U2-4FJX, 2 Ea. Return From T Port 2-Station Hitch Manifold to Port on Cooler Motor (DM-8).
96 H24504 31” 4U2-4FJX, 2 Ea. Pressure From P Port 2-Station Hitch Manifold to Port on Cooler Motor (DM-8).
Model BC-2002/CRC Tandem Diagrams
March 31, 2002 8-57
Table 8-6. Hydraulic/Misc. Hose and Fittings
Item No. Hose Type Length Fitting Hose Description
97 H10408 40” 8U-8FJX & 90D8U-8FJX
From Port on Cooler Pump to Port on Funk Transfer Case.
98 H10408 49” 8U-8FJX & 45D8U-8FJX
From Port on Oil/Water Cooler to Port on Funk Transfer Case.
99 H10408 9” 8U-8FJX & 90D8U-8FJX
From Port on Cooler Pump to Port on Oil/Water Cooler.
100 H06908 210” 6.5U-8FJX, 2 Ea. Port on Oil/Water Cooler to Port on Engine Cooling System.
101 H06908 144” 6.5U-8FJX, 2 Ea. Port on Oil/Water Cooler to Port on Engine Cooling System.
102 H24508 124” 8U-8FJX & 45D8U-8FJX
From Pressure Manifold on Center of Hydraulic Tank to Flow Control Valve Manifolds on Right-Hand Conveyor.
103 PiP-53382 140 1/16” PURCHASED HOSE, 1 ¼”
From Compensator Valve on Belt Pump to Flow Control Valve Manifolds on Right-Hand Conveyor.
104 H10416 72” 16U-16FJX & 90D16U-16FJX
Suction Port on Power Steering/Cooler Pump on Cummins Engine to Strainer on Hydraulic Tank.
105 H10412 90” 12U-12FJX & 90D12U-12FJX
Port on Power Steering/Cooler Pump on Cummins Engine to Bottom Port Return Manifold on Frame.
106 PiP-53391 85” PURCHASED HOSE 1 ½”
Return from Return Manifold on Left-Hand Conveyor to Return Manifold on Right-Hand Frame.
Model BC-2002/CRC Tandem Diagrams
8-58 January 31, 2004
Table 8-7. Hydraulic System Parts and Fittings Chart
Item No. Description Part Number Qty
A 90 3/8” Male Pipe X 5/16” Push On 90D6MP-5PL 1
B 90 ½” Female Pipe X ½” Male Jic 90D8FP-8MJ 1
C Tee ¼” Female Jic X ¼” Male Jic X ¼” Male Jic T4FJX-4MJ-4MJ 1
D 3/8” Male O-Ring X ¼” Male Jic 6MB-4MJ 4
E 90 ½” Male Jic X ½” Male Pipe 90D8MJ-8MP 5
F Tee ¼” Male Jic X ¼” Male Jic X ¼” Male Jic T4MJ-4MJ-4MJ 1
G 90 3/8” Male O-Ring X ¼” Male Jic 90D6MBMJ 4
H 90 ¼” Male O-Ring X ¼” Male Jic 90D4MB-4MJ 9
I ½” Male O-Ring X ½” Male Jic 8MB-8MJ 18
J ½” Male O-Ring X ¼” Male Jic 8MB-4MJ 3
K Cap ¼” Female Jic C4FJ 6
L 90 ¼” Male O-Ring X ½” Male Jic 90D8MB-8MJ 9
M Tee ¼” Male O-Ring X ¼” Male Jic X ½” Male Jic T8MB-8MJ-8MJ 2
N 3/8” Male O-Ring X ½” Female O-Ring 6MB-8FB 2
O 90 3/8” Male O-Ring X ½” Male Jic 90D6MB-8MJ 2
P 1 ¼” Close Nipple FIT-28006 2
Q 1 ¼” Gate Valve VLV-29250 2
R 1 ¼” Male Jic X 1 ¼” Male Pipe 20MJ-20MP 3
S 1 ½” Male O-Ring X 1 ¼” Male Jic 24MB-20MJ 3
T 1 ½” Male O-ring X 1 ¼” Male Jic 90D24MB-20MJ 1
U 1” Male Jic X 1” Male Pipe 16MJ-16MP 1
V 45 1” Flange X 1” Male Jic Code 62 45D16FG-16MJ 1
W ¾” Male O-Ring X ¾” Male O-Ring Union 12MB-12MB 2
X Belt Flow Control Valve VLV-51811 4
Y 90 ¾” Male O-Ring X ¾” Male Jic 90D12MB-12MJ 8
Z Belt On/Off Sol. Valve VLV-53444 4
AA ½” Male Jic X ½” Male Pipe 8MJ-8MP 1
AB 1” Male O-Ring X 1” Male Jic 16MB-16MJ 2
AC Tee ½” Male Jic X ½” Male O-Ring X ½” Male Jic T8MJ-8MJB-8MJ 3
AD 1” Male O-Ring X ½” Female O-Ring 16MB-8FB 1
AE ½” Female Jic Cap C8FJ 2
AF 1” Flange X 1” Male Jic Code 62 16FG62-16MJ 1
AI 1” Flange Clamp code 62 16FG62 6
AJ ¾” Male O-Ring X ¾” Male Jic 12MB-12MJ 4
AK Elbow, Belt Drive Pump FIT-60616 1
AL Tee ¾” Male Pipe X ¾” Male Jic X ¾” Male Jic T12MP-12MJ-12MJ 1
Model BC-2002/CRC Tandem Diagrams
January 31, 2004 8-59
Table 8-7. Hydraulic System Parts and Fittings Chart
Item No. Description Part Number Qty
AM Filter Piping Assembly FTR-51534 1
AN Traction Drive Filter Assembly HSG-51738 1
AO 1 ¼” 90 Street Elbow FIT-28241 1
AP 90 ¾” Male Jic X ¾” Male Pipe 90D12MJ-12MP 1
AQ Chipper Pump/Start Up Valve Assembly MCH-60984 1
AR ¾” Male O-Ring Plug P12MB 1
AS ½” Male O-Ring Plug P8MB 1
AT Bushing ¼” Female Pipe X ½” Male O-Ring 4FP-8MB 1
AU Fan Switch Oil Cooler 150 ELC-51660 1
AV 1 ¼” Male O-Ring X 1 ¼” Male Jic 20MB-20MJ 1
AW ¾” Male O-Ring X ¼” Female O-Ring 12MB-4FB 1
AX ¼” Male O-Ring X ¼” Male Jic 4MB-4MJ 4
AY ½” Male O-Ring X ½” Male Jic 10MB-8MJ 2
AZ Pump Steering/Cooler (Gear) Chipper PMP-53412 1
BA Compensating Pressure Pump PMP-51618 1
BB Belt Drive Motor 22.84 CI PMP-51619 2
BC Sunstrand Pump 90R PMP-53230 1
BD Sunstrand Motor 51V PMP-53231 1
BE Hitch Cylinder CYL-60651 1
BF 90 1” Flange X 1” Male Jic Code 62 90D16FG-16MJ 4
BG 45 ¾” Male Pipe X ¾” Male Jic 45D12MP-12MJ 1
BH 45 1” Male O-Ring X 1 ¼” Male Jic 45D16MB-20MJ 1
BI ¾” Male O-Ring X ½” Male Jic 12MB-8MJ 1
BJ 90D32MJ-32MB With Pressure CK Port FIT-53335 1
BK 90D32MJ-32MB With Temp Sealer CK Port FIT-53336 1
BL Temp Switch (140) Hayden Oil Cooler ELC-53236 1
BM Check Valve Steering Valve VLV-51606 2
BN Plug ¼” Male O-Ring P4MB 1
BO Valve Steering Priority VLV-51604 1
BP Steering Control Valve VLV-51607 2
BQ Oil Cooler Pump (Funk Transfer Case) PMP-52223 1
BR Heat Exchanger Oil/Water PMP-51925 1
BS Funk Transfer Case PTM-53160 1
BT Manifold Pressure Forward (Conveyor) MSC-53280 2
BU Manifold Sub Plate Valve (Valve box) VLV-51613 2
BV Auger Motor PMP-51625 2
BW Motor Hydraulic Cam Gear Box PMP-53160 2
Model BC-2002/CRC Tandem Diagrams
8-60 January 31, 2004
Table 8-7. Hydraulic System Parts and Fittings Chart
Item No. Description Part Number Qty
BX Manifold Hydraulic Return (Small) Hopper MSC-53358 2
BY Cylinder Hopper Extend And Retract CYL-53700 2
BZ Lock-Out Valve 4-Port VLV-22333 2
CA Manifold Hydraulic Return (Belt/Auger) Forward MSC-53376 1
CB Oil Cooler Motor (Funk Transfer Case) PMP-80322 1
CC Shuttle Valve (Sunstrand Pump) VLV-53237 1
CD Hitch Raise Cylinder CYL-53333 1
CE Manifold Hydraulic Return (Frame) MSC-53371 1
CF Manifold Hydraulic Pressure (Forward on Hydraulic Tank) MSC-51600 1
CG Manifold Hydraulic Hitch/Hopper MSC-51621 2
CH Manifold Brake Tee MSC-53268 1
CI 90 ¼” Male O-Ring X ¼’ Male Jic 90D4MB-4MJ 6
CJ 90 ½” Male O-Ring X ¼” Male Jic 90D8MB-4MJ 10
CK 90 3/8” Male Pipe X ¼” Male Jic 90D6MP-4MJ 5
CL 3/8” Male Pipe X ½” Male Jic 8MJ-6MP 1
CM 3/8” Male Pipe X ¼” Male Jic 4MJ-6MP 2
CN 45 ¾” Male O-Ring X ¾” Male Jic 45D12MB-12MJ 1
CO 90 1” Male O-Ring X ¾” Male Jic 90D16MB-12MJ 3
CP ¼” Male Pipe X ¼” Male Jic 4MJ-4MP 2
CQ 90 ¼” Male Pipe X ¼” Male Jic 90D4MJ-4MP 2
CR 45 ¼” Male Pipe X ¼” Male Jic 45D4MJ-4MJ 2
CS 45 ¾” Male O-Ring X ½” Male Jic 45D12MB-8MJ 4
CT 5/8” Male O-Ring X ¼” Female O-Ring Bushing 10MB-4FB 4
CU 2” Male O-Ring x 1 ½” Female O-Ring Bushing 32MB-24FB 1
CV 45 1 ½” Male O-Ring X 1 ½” Male Jic 45D24MB-24MJ 1
CW 1 ½” Male O-Ring Plug P24MB 1
CX 1 ¼” Male O-Ring X 1-1/4” Male O-Ring Union 20MB-20MB 1
CY 45 ¼” Male O-Ring X ¼” Male Jic 45D4MB-4MJ 1
CZ 90 ¾” Male Pipe X ½” Male Jic 90D12MB-8MJ 1
DA 3-Filter Head Assembly FTR-51731 1
DB 2-Filter Head Assembly FTR-51732 1
DC Suction Filter Housing (Cooler Pump) HSG-53413 1
Model BC-2002/CRC Tandem Parts Index
July 15, 2002 9-1
SECTION 9. PARTS INDEX
This section contains an alphabetical listing of parts for the BC-2002/CRC Tandem. The part description, part number, and illustrated parts list (IPL) figure number and item number is given. Standard hardware such as nuts, bolts, and washers is not included in this parts index. Standard hardware is listed in the applicable figure of the IPL.
Description Part No. Fig Item ½” Female Jic Cap C8FJ 7-17 6
½” Male Jic X ¼” Male Pipe 8MJ-4MP 7-6 35
½” Male Jic X ¼” Male Pipe 8MJ-4MP 7-9 10
½” Male O-Ring X ½” Male Jic 8MB-8MJ 7-13 12
½” Male O-Ring X ½” Male Jic 8MB-8MJ 7-13 15
½” Male O-Ring X ½” Male Jic 8MB-8MJ 7-19 9
½” Male O-Ring X ½” Male Jic 8MB-8MJ 7-20 8
½” Male O-Ring X ¼” Male Jic 8MB-4MJ 7-20 7
½” Male Pipe X ¾” Bulk Head X ½” Male Pipe 8MP-12BH-8MP 7-9 9
¼” Close Nipple FIT-28001 7-6 37
¼” Grease Zerk .250-28M-2 7-8 2
¼” Male Jic X ¼” Male Pipe 4MJ-4MP 7-9 12
¼” Male Jic X ¼” Male Pipe 4MJX4MP 7-26 8
¼” Male O-Ring X ¼” Male Jic 4MB-4MJ 7-13 9
1/8” Male Grease Zerk 2MP-Z 7-23 21
3/16” X 3/16” X 2” Key STL-30951 7-23 20
3/8” Male O-Ring X ¼” Male Jic 6MB-4MJ 7-13 11
3/8” Male O-Ring X ¼” Male Jic 6MB-4MJ 7-26 15
4” X 20” Stroke Hydraulic Cylinder CYL-51962 7-26 4
90 ½” Male O-Ring X ½” Male Jic 90D8MB-8MJ 7-13 13
90 ½” Male O-Ring X ½” Male Jic 90D8MB-8MJ 7-19 7
90 ½” Male O-Ring X ½” Male Jic 90D8MB-8MJ 7-20 5
90 ¼” Male Jic X ¼” Male Pipe 90D4MJ-4MP 7-9 15
90 ¼” Male Jic X ¼” Male Pipe 90D4MJ-4MP 7-26 13
90 ¼” Male O-Ring X ¼” Male Jic 90D4MB-4MJ 7-13 10
90 ¼” Male O-Ring X ¼” Male Jic 90D4MB-4MJ 7-13 14
90 Male Pipe 90D8MB-4MJ 7-24 5
A
Air Dryer Assembly FTR-60945 7-3 25
Air Intake Precleaner FTR-51855 7-2 78
Air Supply Line Assembly, Tow Bar PIP-60842 7-26 21
Model BC-2002/CRC Tandem Parts Index
9-2 July 15, 2002
Description Part No. Fig Item Air Tank TNK-53080 7-21 18
Air Tank Assembly TNK-51993 7-6 27
Air Tank Spacer BRK-51573 7-6 26
Angle Brace BRK-61609 7-11 12
Angle Brace BRK-61610 7-12 12
Antenna 39 ½” Height, Magnetic Base ELC-60637 7-16 23
Auger 14”, Left-Hand PTM-53130 7-21 3
Auger 14”, Right-Hand PTM-53131 7-21 –
Auger Bearing End Shaft PTM-53106 7-21 4
Auger Motor PMP-51625 7-21 1
Auger Motor End Shaft PTM-53105 7-21 2
Axle Assembly, Modified (2WD) PTM-53348 7-2 147
Axle Assembly, Rear Drive (4WD) PTM-53226 7-2 150
Axle, Spicer/Dana HD 1350 PTM-61457 7-7 1
B
Back-Up Alarm ELC-24293 7-2 141
Baffle BRK-53090 7-2 246
Baffle, Air Dryer BRK-60948 7-6 4
Barrier Strip, 6-Gang ELC-24190 7-22 2
Barrier Strip, 20 Lug ELC-24220 7-24 17
Battery Box HSG-51560 7-6 29
Beacon ELC-24215 7-2 96
Bearing #11910 Cup PTM-50846 7-23 5
Bearing #LM48510 Cup PTM-50848 7-23 7
Bearing 4-Bolt PTM-51905 7-21 24
Bearing Gear Box #48548 PTM-50847 7-23 6
Bearing Gear Box #LM11949 PTM-50845 7-23 4
Bearing Guard GRD-53212 7-21 5
Bearing, Pillow Block PTM-51415 7-2 234
Bearing Plate BRK-53020 7-21 26
Belt Motor Assembly PTM-51619 7-2 72
Blank Cover C-7 MSM-50899 7-24 19
Bore Coupling 2 7/16” PTM-50837 7-21 15
Bracket BRK-53353 7-2 276
Bracket BRK-61048 7-10 5
Bracket BRK-51407 7-11 13
Bracket BRK-51407 7-12 14
Bracket, Air Cleaner Support BRK-51826 7-3 12
Model BC-2002/CRC Tandem Parts Index
July 15, 2002 9-3
Description Part No. Fig Item Bracket, Auger Mount BRK-53056 7-21 17
Bracket, Bearing Mount BRK-51416 7-2 228
Bracket, Cooler Mount BRK-53402 7-3 22
Bracket, Double Intake Filter BRK-51680 7-6 3
Bracket, Double Timbren Spring BRK-61468 7-6 1
Bracket, Hinge / Base BRK-53246 7-15 10
Bracket, Hitch Manifold, Tow Bar Glad Hand BRK-61048 7-9 3
Bracket, Inner Conveyor Rail to Hydraulic Tank BRK-51425 7-2 219
Bracket, Latch T-Handle FAS-24387A 7-14 6
Bracket, Outer Conveyor Rail to Hydraulic Tank BRK-53355 7-2 216
Bracket, Primary Fuel Filter BRK-60615 7-6 7
Bracket, Rear BRK-61479 7-2 195
Bracket, Shuttle Valve, Sunstrand Pump BRK-53262 7-3 14
Bracket, Swaybar (Right-Hand & Left-Hand) BRK-51485 7-6 22
Bracket, Tank to Conveyor BRK-60604 7-2 183
Bracket, Throttle Cable BRK-61681 7-3 27
Bracket, Tow Bar, Quick Disconnect BRK-53409 7-21 11
Bracket, Triple Return Filter BRK-51679 7-6 2
Brackets BRK-61696 7-2 213
Brake Mount BRK-53315 7-7 15
Break Away Switch ELC-24281 7-16 8
Breather Assembly, Hydraulic Tank FTR-51539 7-3 2
Bushing BRK-50738 7-21 34
Bushing BRK-50738 7-25 9
Bushing Hex ½” X ¼” FIT-28344 7-9 14
Bushing Hex ½” X ¼” FIT-28344 7-26 6
Bushing Hex ½” X ¼” FIT-28344 7-26 10
C
Cable 7-Cond. Stranded Trailer Cable ELC-24058 7-9 11
Cable Assembly PTM-51634 7-16 1
Cam Stop BRK-53070 7-21 44
Camshaft MCH-53075 7-21 46
Camshaft 1’ MCH-54048 7-25 5
Cap FIT-26045 7-2 177
Cap ¼” Female Jic C4FJ 7-13 –
Capacitor, Axial 100 MFD ELC-24551 7-22 1
Cat Walk GRD-53311 7-2 249
Cat Walk GRD-53133 7-2 294
Model BC-2002/CRC Tandem Parts Index
9-4 July 15, 2002
Description Part No. Fig Item Cat Walk, Left-Hand, Tandem GRD-53157 7-11 6
Cat Walk, Right-Hand, Tandem GRD-53314 7-12 6
CB, 40 Channel ELC-60636 7-16 22
Chain PTM-50834 7-21 13
Chain Assembly, Mirror FAS-61052 7-2 264
Chain Strap BRK-60797 7-7 10
Channel HSG-53381 7-6 16
Channel BRK-61485 7-6 17
Channel HSG-53138 7-7 7
Channel Stiffener BRK-53241 7-2 171
Chip Box Extension 7-25
Chip Box Weldment HSG-53010 7-21 23
Chip Box, Tandem 7-21
Chrome Plug FIT-24219 7-24 12
Cinch Connector 6 Lug ELC-24190 7-14 11
Circuit Breaker, 15 Amp ELC-24289 7-14 3
Circuit Breaker, 30 Amp ELC-24290 7-24 7
Clamp Muffler 1 ½” FAS-29362 7-13 19
Clamp, Cable FAS-60982 7-16 10
Clamp, Conveyor Rear Seal BRK-51798 7-2 132
Clamp, Conveyor Rear Side Seal BRK-60647 7-2 123
Clamp, Horizontal Seal BRK-51246 7-2 120
Clamp, Vertical Seal BRK-51785 7-2 102
Clevis (1/4” Pin) FAS-51635 7-16 2
Clevis (5/16” Pin) FAS-51758 7-16 3
Clip Click Pin, Spring Loaded FAS-60821 7-26
Companion Flange 2-1-333 PTM-22273 7-4 1
Compensator Pump Elbow FIT-60616 7-3 5
Conical Nut FAS-61487 7-3 31
Connector, Cinch, 10 Lug ELC-24188 7-14 10
Connector 20 Lug Barrier Strip ELC-24220 7-14 13
Connector Strain Relief ½” ELC-24420 7-24 27
Control, Positive Lock MCH-51633 7-16 4
Conveyor Assembly, Left-Hand (See Figure 7-11 for Details)
HSG-53149 7-11 201
Conveyor Assembly, Right-Hand (See Figure 7-12 for Details)
HSG-53150 7-2 33
Conveyor Belt, Hot RS (30” x 489”) MSC-51767
Conveyor Belt, Hot LS (30” x 547”) MSC-60400
Conveyor Belt, Standard RS (30” x 489”) MSC-60482
Conveyor Belt, Standard LS (30” x 547”) MSC-60485
Model BC-2002/CRC Tandem Parts Index
July 15, 2002 9-5
Description Part No. Fig Item Conveyor Rail #1 Left-Hand Outer, Tandem HSG-53151 7-11 18
Conveyor Rail #2 Left-Hand Inner, Tandem HSG-53152 7-11 8
Conveyor Rail #3 Right-Hand Inner HSG-53153 7-12 8
Conveyor Rail, #4 Right-Hand Outer HSG-53154 7-12 23
Cotter Pin ¼” X 2 ½” FAS-25944 7-17 –
Cotter Pin 3/16” X 2” FAS-25935 7-17 –
Coupling, Pot Drive, Female PTM-53270 7-22 5
Coupling, Pot Drive, Male PTM-50972 7-22 7
Coupling, Taper Lock, Female PTM-60663 7-2 57
Coupling, Taper Lock, Male PTM-60664 7-2 60
Cover, Chain coupler/auger motor PTM-50835 7-21 14
Cover, Guard. Proximity Switch auger/belt HSG-50801 7-2
7-21
Cover, Hydraulic Manifold Closed Center HSG-27355 7-19 5
CRC Display MTR-51753 7-16 13
Cross Channel HSG-51428 7-11 9
Cross Channel HSG-51428 7-12 9
Cross Member BRK-61706 7-11 16
Cross Member BRK-53351 7-12 17
Cross Member BRK-61706 7-12 21
Cross Member Aft BRK-53099 7-2 48
Cross Member Forward BRK-53100 7-2 51
Cross Member With Guard BRK-53370 7-12 19
Cummins 6CT 8.3 (230 HP) MCH-51849 7-3 1
Current Breaker 50 Amp ELC-24184 7-14 9
Cylinder CYL-50919 7-25 4
Cylinder 1 ½” X 10” CYL-22300 7-18 8
D
Diaphragm, Proximity Switch (auger/belt) MSC-50831 7-2
7-21
Diesel Tank TNK-61824 7-2 174
Din Connector ELC-24416 7-24 18
Dip Stick 60” MTR-51862 7-3 34
Dip Stick Tube PIP-53303 7-3 35
Directional Control Valve, Closed Center VLV-51621 7-18 1
Directional Control Valve, Closed Center VLV-51621 7-20 2
Door Assembly Left-Hand HSG-53294 7-2 27
Door Assembly Right-Hand HSG-53300 7-2
Double Check Valve, Stack-Up VLV-51920 7-18 3
Dowel Pin ½” I.D. X ¾” FAS-25353 7-23 18
Model BC-2002/CRC Tandem Parts Index
9-6 July 15, 2002
Description Part No. Fig Item Drivelines 7-4
Drop Leg Jack MSC-51960 7-26 2
E
Earphone ELC-60638 7-16 21
Elbow Pipe Street ½” FIT-28238 7-26 9
End Plate Set VLV-50900 7-24 26
Engine, Cummins 6CT 8.3 (1999-2002) MCH-51849 7-3 1
Engine, Cummins QSB-44 (2003 & Newer) MCH-51833
Engine Mount Assembly, Rear BRK-51460 7-3 9
Engine Mount, Front HSG-51472 7-6 15
Exhaust Clamp Connector Stainless Steel FIT-51871 7-5 10
Exhaust Clamp U Guillotine Type FAS-51872 7-5 8
Exhaust Connector Tube FIT-51874 7-5 5
Exhaust Elbow 18” X 18” 90 FIT-51873 7-5 6
Exhaust Elbow 18” X 18” 90 (6” Cut Off End) Modified FIT-51873
7-5 9
Exhaust Nipple (4” X .083” Wall Tube X 6” Long) 7-5 4
Exhaust System (See Figure 7-5 for Details)
MSC-51869 7-3 10
Exhaust Tube 4” X .083” W. Nipple Exhaust FIT-51885 7-5 7
Exhaust Tubing Flex 4” X 10 ½” FIT-51872 7-5 11
Extension Weldment 1’ HSG-54049 7-25 14
F
Face Gear Box Housing HSG-50622 7-23 2
Fan Cover HSG-53245 7-15 5
Fan Electric, Oil Cooler ELC-53231 7-15 3
Fender Strut BRK-51805 7-3 11
Filter Head Assembly, Suction FTR-51731 7-3 26
Flange Yoke 2-2-329 PTM-22251 7-4 2
Flange Yoke 2-2-479 PTM-22252 7-4 3
Flange Yoke 4-2-669 7-4 7
Flange Yoke 4-2-669 7-4 11
Flasher Clip BRK-51850 7-14 5
Flasher, Heavy Duty 2-Terminal ELC-101889 7-14 4
Foot Pedal Brake Valve BRK-51240 7-16 17
Foot Pedal, Digital (2002) ELC-51836 7-16 –
Foot Switch, Varior Potentiometer (2000 – 2001) ELC-51832 7-16 19
Model BC-2002/CRC Tandem Parts Index
July 15, 2002 9-7
Description Part No. Fig Item Frame Assembly
(See Figure 7-6 for Details) HSG-53135 7-3 20
Frame Rail, Left-Hand HSG-61481 7-6 24
Frame Rail, Right-Hand HSG-61480 7-6 25
Front Fender GRD-51806 7-3 15
Fuel Filter Assembly, Primary FTR-60953 7-3 24
G
Gasket, Valve to manifold RNG-27266 7-24
Gate Assembly 12” MCH-53050 7-21 30
Gate Assembly 12” MCH-53030 7-25 8
Gate Cylinder Assembly CYL-50919 7-21 33
Gear Box Assembly (See 7-23 for Details)
PTM-53377 7-21 45
Gear Box Housing HSG-50621 7-23 1
Gear Box, Split Gear PTM-53461 7-23 14
Gear Box, Thrust Bearing Matched Pairs
PTM-53462 7-23 3
Glad Hand ELC-22375 7-9 8
Glad Hands ELC-22375 7-26 22
Grizzly, Receiving Hopper BRK-51846 7-2 129
Grizzly, Tandem Hopper GRD-53204 7-21 19
Ground Strap 12” ELC-24011 7-16 24
Guard GRD-53411 7-2 297
Guard Rail, Conveyor (2000 – 2001) GRD-61701 7-2 36
Guard Rail, Conveyor (2002) GRD-53426 7-2 309
Guard Rail, Front Inside (2000 – 2001) GRD-53317 7-2 30
Guard Rail, Front Inside (2002) GRD-53429 7-2 306
Guard, Potentiometer Barrier Strip GRD-53127 7-21 47
Gusset BRK-61043 7-6 11
Gusset BRK-20235 7-6 14
Gusset Pan Hard BRK-53141 7-6 23
H
Hand Rail, Aft (2000 – 2001) GRD-51566 7-2 111
Hand Rail, Aft (2002) GRD-51566 7-2 315
Hand Rail, Front (2000 – 2001) RNG-53307 7-2 9
Hand Rail, Front (2002) RNG-53424 7-2 300
Hand Rail, Front/Side (2002) RNG-53425 7-2 303
Head Pulley Assembly PTM-61404 7-2 240
Heat Exchanger, Transfer Case PMP-51925 7-3 21
Helix Angle Worm #WGA-1G For PTM-53463 7-23 12
Model BC-2002/CRC Tandem Parts Index
9-8 July 15, 2002
Description Part No. Fig Item Hex Bolt ¼” – 20 X 2 ¼” FAS-28707 7-13
Hex Bushing 3/8” X ¼” FIT-28342 7-6 36
Hitch Assembly MCH-53216 7-2 165
Hitch MCH-51500 7-17 12
Hitch Assembly Cylinder Bracket BRK-51505 7-17 4
Hitch Cylinder CYL-60651 7-17 2
Hitch Cylinder Pin Assembly FAS-60941 7-17 10
Hitch Hook BRK-61501 7-17 11
Hitch Lift 7-18
Hitch Manifold (W/Fittings Only) HSG-61500 7-9 2
Hitch Manifold (W/Fittings Only) HSG-61500 7-10 3
Hitch Manifold W/Lift Option 7-20
Hitch Manifold W/Out Lift Option 7-19
Hitch Pin BRK-60658 7-17 1
Hitch Pin FAS-51506 7-17 9
Hitch X-Member BRK-53229 7-2 168
Hood HSG-61708 7-2 210
Hook, Left-Hand BRK-51472 7-6 21
Hook, Right-Hand BRK-51471 7-6 20
Horizontal Mufflers MSC-51875 7-5 2
Horizontal Seal Stiffener, Inner BRK-51914 7-2 159
Horizontal Seal Stiffener, Outer BRK-51915 7-2 156
Hose #4 X 146” Long PIP-51762 7-18 16
Hose #4 X 156” Long PIP-51760 7-18 17
Housing, Potentiometer MSC-53067 7-22 4
Hub Assembly, Tow Bar PTM-51964 7-26 20
Hydraulic Cylinder Shoe BRK-60787 7-26 25
Hydraulic Motor Gear Box PMP-53160 7-21 31
Hydraulic Supply Line Assembly PIP-60844 7-26 14
Hydraulic Tank Assembly TNK-53158 7-3 33
Hydraulic Valve Closed Center VLV-51621 7-24 1
I
Inlet Check Valve VLV-51606 7-13 16
Insulator ELC-50152 7-24 9
J
Junction Box ELC-60950 7-2 198
Model BC-2002/CRC Tandem Parts Index
July 15, 2002 9-9
Description Part No. Fig Item Junction Box
(See Figure 7-14 for Details) ELC-60931 7-13 5
Junction Panel Assembly HSG-51848 7-14 7
L
Ladder Assembly GRD-51528 7-2 189
Latch T-Handle FAS-24387 7-14 1
Lifting Eye, Transfer Case BRK-53224 7-3 17
Light, Markers ELC-51596 7-2 138
Light, Turn ELC-51587 7-2 225
Light, Work ELC-51585 7-2 75
Limit Switch Assembly (Proximity) MTR-53202 7-2 21
Lock Out Valve VLV-22319 7-26 12
M
Male Pipe 8MB-4MJ 7-24 4
Male Pipe 4MJ-4MP 7-24 22
Male Pipe 8MJ-6MP 7-24 25
Manifold Assembly HSG-61500 7-18 4
Manifold, Auger / Belt control (pressure) MSC-53280 7-2 6
Manifold, Auger / Belt (return) MSC-53376 7-2 39
Manifold, Hydraulic Return MSC-53358 7-21 38
Manifold, Pressure MSC-51600 7-3 3
Manifold, Return MSC-53371 7-3 8
Manifold, Steering MSC-60995 7-13 3
Manifold, Sub Plate VLV-51613 7-24 6
Manifold, 2-Station Parallel MSC-51621 7-19 6
Manifold, 2-Station Parallel MSC-51621 7-20 4
Master Cylinder PTM-51644 7-10 1
Mirror GRD-61050 7-2 12
Mirror Base BRK-61051 7-2 15
Modified Box HSG-53111 7-24 28
Modified Coupling PTM-53065 7-21 16
Modified Seal Bracket BRK-53096 7-21 29
Motor Mount Gear Box BRK-50855 7-23 13
Model BC-2002/CRC Tandem Parts Index
9-10 July 15, 2002
Description Part No. Fig Item Motor, Sunstrand 51V, Hydrostatic Motor PMP-53231 7-3 19
Mount Angle Cylinder Hitch Lift BRK-61613 7-12 13
Mount Cam/Gate MCH-53052 7-21 40
Mount Cam/Gate MCH-53052 7-25 12
Mounting Plate BRK-51536 7-2 69
Mud Flap GRD-51815 7-3 7
Muffler Hanger BRK-51877 7-5 3
N
Nipple ¼” X Close Sch. 80 FIT-28001 7-26 11
Nut Inner Spacer 7/8” – 9 7-18
O
Oil Cooler PTM-53230 7-15 1
Oil Cooler Assembly (See Figure 7-15 for Details)
HSG-53233 7-2 93
O-Ring 1 3/8” I.D. RNG-20910 7-22 9
P
Panel BRK-53299 7-2 18
Panel Assembly, 2-Wheel Drive (See Figure 7-9 for Details)
HSG-61069 7-6 12
Panel Assembly, 4-Wheel Drive (See Figure 7-10 for Details)
BRK-61059 7-6 –
Panel, Right-Hand Side, Left-Hand Conveyor HSG-53295 7-2 261
Parking Brake Assembly PTM-53235 7-7 14
Parking Brake Knob MSC-51829 7-16 11
Pedestal and Control Box Assembly (See Figure 7-16 for Details)
HSG-53372 7-2 84
Pedestal Assembly, Tandem HSG-53373 7-16 26
Pillow Block, Bearing PTM-51415 7-2 234
Pintle Eye MSC-51961 7-26 1
Plate Base HSG-54058 7-25 11
Plate, Bottom, Left-Hand & Right-Hand BRK-53134 7-7 8
Plate, Conveyor to Frame HSG-53222 7-6 33
Plate, Left-Hand Top BRK-53137 7-7 2
Plate, Rear Axle BRK-53225 7-11 10
Plate, Rear Axle BRK-53225 7-12 11
Plate, Right-Hand Top BRK-53136 7-7 3
Model BC-2002/CRC Tandem Parts Index
July 15, 2002 9-11
Description Part No. Fig Item Platform Gripstrut GRD-53278 7-2 90
Platform Mid HSG-53271 7-2 87
Platform Support/Forward Tube Assembly BRK-60673 7-13 1
Platform with Seat Base, Right-Hand & Left-Hand HSG-53342 7-2 153
Plug ½” Male O-Ring P8MB 7-19 8
Plug ½” Male O-Ring P8MB 7-20 6
Plug Trailer 7-Cond. ELC-24246 7-26 24
Potentiometer ELC-53128 7-22 3
Potentiometer Assembly (See 7-22 for Details)
ELC-53322 7-21 37
Pressure Check Port Only (Modified 90D32MB-32MJ) FIT-53336 7-15 9
Pressure Reducing Valve VLV-51929 7-24 3
Proximity Switch Assembly, Conveyor Control MTR-53202 7-2 21
Proximity Switch Assembly, Auger Control MTR-53213 7-21 6
Pump, Pressure Compensator, Belt Pump PMP-51618 7-3 4
Pump, Steering PMP-80016 7-3 28
Pump, Sunstrand 90R, Hydrostatic Pump PMP-53230 7-3 16
Q
Quick Coupler, Female FIT-60911 7-21 9
Quick Coupler, Male FIT-60912 7-21 10
Quick Disconnect Male HP ¼” X 6 Mor FIT-29632 7-26 16
R
Radar Assembly (4-WD Option Only) HSG-53350 7-3 23
Radiator MSC-50814 7-3 37
Radiator Shield GRD-51842 7-3 36
Rear Fender GRD-51808 7-2 180
Receiving Hopper HSG-53365 7-2 99
Regulator, 45# Fixed VLV-26201 7-6 39
Relay 70 Amp ELC-24270 7-14 8
Relay Socket ELC-81005 7-14 14
Remote Box Assembly HSG-53331 7-2 282
Restrictor Fitting FIT-29980 7-18 7
Retainer, Cam Motor BRK-53069 7-21 32
Retainer, Hose Guide GRD-53374 7-21 39
Model BC-2002/CRC Tandem Parts Index
9-12 July 15, 2002
Description Part No. Fig Item Return Roller Assembly PTM-51433 7-12 7
Return Rollers PTM-51413 7-11 7
Right-Hand & Left-Hand Stanchion Plate BRK-51481 7-6 6
Rim Assembly White Rim 16.5 X 6.75 Spoked 8-6.5 MSC-80126 7-26
Ring, Chaffing 4” I.D. RNG-26422 7-6 10
Ring, Rear Frame Hosing RNG-53343 7-6 9
Riser, Seal Support BRK-21447 7-25 6
Rock Box End Panel, Left-Hand HSG-53293 7-2 267
Rock Box End Panel, Right-Hand HSG-53298 7-2 270
Rock Box Panel Left-Hand, Front HSG-53291 7-2 252
Rock Box Panel Left-Hand, Rear HSG-53292 7-2 255
Rock Box Panel Right-Hand, Front HSG-53296 7-2 285
Rock Box Panel Right-Hand, Rear HSG-53297 7-2 288
Runner, Bearing Load PTM-53010 7-21 20
S
Safety Chain Lift Cylinder Shoe BRK-60829 7-26 3
Safety Chain Tow Bar BRK-60828 7-26 26
Scraper, Rock GRD-53279 7-21 22
Seal RNG-53320 7-2 24
Seal RNG-53068 7-21 27
Seal 1’ RNG-54059 7-25 1
Seal Support Bracket BRK-53071 7-21 28
Seal Wiper, Head Pulley LH RNG-53395 7-2 258
Seal Wiper, Head Pulley LH RNG-53395 7-2 291
Seal Wiper, Head Pulley RH RNG-53396
Seal, Conveyor Flashing RNG-51793 7-2 126
Seal, Horizontal RNG-51796 7-2 114
Seal, Horizontal Conveyor RNG-60645 7-2 135
Seal, Vertical RNG-51795 7-2 105
Seal, 45 Corner RNG-53394 7-2 108
Seat MSC-51773 7-2 117
Security Box Assembly HSG-51697 7-16 12
Sensor / Pressure Check Port (Modified 90D32MB-32MJ)
FIT-53335 7-15 8
Shaft, Worm Drive Gear Box PTM-50856 7-23 11
Shroud HSG-53244 7-15 7
Slave Box Assembly HSG-53143 7-2 273
Model BC-2002/CRC Tandem Parts Index
July 15, 2002 9-13
Description Part No. Fig Item Sling Cable Assembly PTM-53333 7-18 11
Slip Yoke 4-3-1241KX 7-4 6
Slip Yoke 4-3-1241KX 7-4 10
Snap Ring FAS-53017 7-21 21
Snatch Block PTM-52053 7-18
Snatch Block Assembly 7-18 10
Socket 7-Pole Trailer Conn. ELC-24245 7-9 7
Socket Boot ELC-24247 7-9
Spacer BRK-53240 7-7 9
Spacer PTM-53323 7-18
Spacer BRK-53116 7-24 14
Spacer 3/16” BRK-61440 7-6 19
Spacer, Bearing BRK-53057 7-21 25
Spacer, Spherical Bearing PIP-51518 7-7 4
Spacer, Tandem A-Frame HSG-53243 7-7 13
Spacer, Valve Box BRK-53272 7-21 8
Speedo Gear Large 19 Tooth PTM-50843 7-23 9
Spherical Bearing PTM-51517 7-8 3
Spherical Bearing Retainer HSG-51513 7-8 4
Spindle Assembly, Tow Bar BRK-60832 7-26 19
Spring Assembly MCH-51816 7-18 12
Stanchion Pipe, Wet Air Tank HSG-51473 7-6 13
Start Up Cable with Tee Handle & Clevis PTM-60980 7-16 7
Steering Assembly (2000 – 2001) (See Figure 7-13 for Details)
BRK-51529 7-2 81
Steering Assembly (2002) (See Figure 7-13 for Details)
BRK-51529 7-13 312
Steering Column 30” MCH-51608 7-13 18
Steering Shuttle Valve VLV-51605 7-13 2
Steering Wheel MCH-51609 7-13 8
Steering Wheel Cap MCH-51610 7-13 6
Steering Wheel Nut FAS-51611 7-13 7
Stiffener BRK-53257 7-2 42
Stiffener BRK-53260 7-2 45
Strain Relief 7-18 2
Stub Shaft MCH-51412 7-11 14
Stub Shaft MCH-51412 7-12 15
Model BC-2002/CRC Tandem Parts Index
9-14 July 15, 2002
Description Part No. Fig Item Support Locator, Potentiometer BRK-53109 7-21 36
Support Panel, Left-Hand BRK-53081 7-2 204
Support Panel, Right-Hand BRK-53083 7-2 1
Support Track BRK-53112 7-21 12
Support Tube BRK-60925 7-6 18
Support, Lower BRK-60696 7-2 192
Support, Receiving Hopper to Conveyor BRK-60614 7-2 144
Support, Upper BRK-60667 7-2 186
Swaybar Assembly PTM-51459 7-3 6
Swing Away Hitch Assembly MCH-60796 7-26 27
Switch Panel HSG-53115 7-24 16
Switch, Micro (Proximity Switch for auger/belt) ELC-50915 7-2
7-21
Switch, Mom – Off – Mom ELC-24274 7-24 11
Switch, On/Off Single Pole ELC-24275 7-24 13
T
Tail Pipe FIT-51884 7-5 1
Tail Pulley Assembly MCH-51403 7-11 3
Tail Pulley Assembly MCH-51403 7-12 3
Take-Up Bearing PTM-51417 7-11 4
Take-Up Bearing PTM-51417 7-12 4
Take-Up Bearing Adjustment Assembly MCH-51965 7-11 1
Take-Up Bearing Adjustment Assembly MCH-51965 7-12 1
Taper Lock 1 ½” PTM-60666 7-2 63
Taper Lock 1 15/16” PTM-60665 7-2 66
Taper Lock, Coupling, Female PTM-60663 7-2 57
Taper Lock, Coupling, Male PTM-60664 7-2 60
Tee ½” Male Jic X ½” O-Ring X ½” Male Jic T8MJ-8MB-8MJ 7-17 5
Tee ¼” Male Jic X ¼” Male Jic X ¼” Male Pipe T4MJ-4MJ-4MP 7-26 7
Timbren MSC-100130 7-3 30
Tire 9.50-16.5 10 Ply Radial (Tow Bar) MSC-80127-T 7-26 –
Tow Bar Assembly 7-26
Tow Bar Chipper Pin, 2” BRK-60823 7-26 18
Tow Bar Cylinder Top & Bottom Pins BRK-60825 7-26 5
Track Support BRK-53087 7-2 243
Track Support, Aft BRK-53366 7-2 222
Model BC-2002/CRC Tandem Parts Index
July 15, 2002 9-15
Description Part No. Fig Item Track Support, Front BRK-53341 7-2 279
Trailer Cord Assembly Chipper Tow Bar ELC-60840 7-26 23
Transfer Case PTM-53160 7-3 18
Trough Roller MCH-51402 7-12 10
Trough Rollers Assembly MCH-51402 7-11 11
Tube Shaft 4-40-761 7-4 5
Tube Shaft 4-40-761 7-4 9
Tube X-Member Transmission Mount BRK-53223 7-6 30
U
U-Joint 1550 5 – 155x PTM-51548 7-4 4
U-Joint 1550 5 – 155x PTM-51548 7-4 8
V
Valve Assembly, 12 Station VLV-50917 7-24 23
Valve Box Assembly (See Figure 7-24 for Details)
HSG-53110 7-21 7
Valve Brake Control VLV-51640 7-16 5
Valve S/S 3-Way Ball Valve VLV-29216 7-9 13
Valve Sol. Dir. Control Closed Center VLV-51621 7-19 2
Valve, Sol. Belt On/Off VLV-53444
Valve Steering VLV-51607 7-13 17
Valve, Double Check Stack-Up VLV-51920 7-19 3
Valve, Double Check Stack-Up VLV-51920 7-20 3
Valve, Four Way Versa Valve VLV-50902 7-24
Valve, Quick Release VLV-51642 7-6 34
Valve, Shuttle, Sunstrand Pump VLV-53237 7-3 13
W
Wheel & Tire Assembly MSC-80087 7-26 17
Wheel Adapter BRK-61491 7-3 32
Wire Rope Clamp 3/4” FAS-51446 7-2 162
Wiring Console Assembly SCH-51510 7-16 15
Wishbone Assembly (See Figure 7-7 for Details)
HSG-53139 7-3 29
Working Light ELC-51585 7-2 75
Model BC-2002/CRC Tandem Parts Index
9-16 July 15, 2002
Model BC-2002/CRC Tandem Parts Index
July 15, 2002 9-17
Blank Page