IMPORTANT: If installing a Pivot Door and Side Panel, ie. a corner installation, please refer to alternative fixing details on the document reverse.

Bi-fold DoorInstallation Instructions

• Instruction suitable for both Right and Left Hand fixing variations.

Please note: Enclosure shown is for Illustration purposes only. IN00443 (rev B)

2 YEAR GUARANTEE

IMPORTANT: If installing a Slider Door only, ie. a recess installation, please refer to alternativefixing details on the document reverse.

Slider Door & Side PanelInstallation Instructions

• Instruction suitable for both Right and Left Hand fixing variations.

Please note: Enclosure shown is for illustration purposes only. IN00445 (rev B)

• Check that the tray has been installed correctly and that it is level (Fig. A) Tiled down onto and sealed to the manufacturer’s guidelines. Please Note: All product is supplied without a tray.

• Ensure the product is fitted to a non-porous surface eg ceramic tiles & waterproof panels.• Check that the wall surface is flat.• Unpack and check the product is complete and undamaged.

• Handle all glass with care - support on cardboard to avoid risk of breakage.• This product is heavy and requires 2 people to carry and install it.• When drilling walls, check first for hidden pipes and cables.• All glass is toughened – it cannot be reworked or replaced by ordinary glass.• Use safety eyewear when drilling.• Use safety eyewear when handling glass.• Keep all small parts away from children.

Safety

• Please notify the retailer immediately of any damage or faults. The manufacturer cannot be held responsible for any installation costs that may arise from damaged or faulty product being installed.

• Please dispose of all packaging with due regard to the environment.

Disclaimer

Before You Start

Tools Required (not supplied)

Fig. A

Spirit Level Screwdriver Tape Measure

Junior Hacksaw

Pencil Utility Knife

Silicone Gun & Sealant Power Drill Suitable Drill Bits

6mm dia. *

3mm dia. HSS

* Ensure drill bit used is suitable for wall surface

• Fixings are supplied for solid walls only. Ensure that the correct fixings are used for the wall type – if in doubt seek professional advice.

• Ensure the area is clean, dry and dust free.• Read the instructions in full.• Have the correct tools available,

(See ‘Tools Required’ below).• It is recommended to situate the showerhead and

door adjacent to each other in order to allow any water spray to be on the side panel or upstanding wall.

We have taken great care to ensure that this product reaches you in perfect condition. However should any parts be damaged or missing please contact your point of purchase. This does not affect your statutory rights. In addition if you require replacement parts your point of purchase will be happy to assist.

Parts & Fittings Supplied

Please notify the retailer immediately of any damage or faults. The manufacturer cannot be held responsible for any installation costs that may arise from a damaged or faulty product being installed.

!Keep small parts away from children!

Side PanelX1

Glass Panel AssemblyX1

Glass DoorX1

D2

D1

D3

D4

D6

D5

A

Wall Channel X2

E

D

D1

D3D2

*Wall ChannelCap X3

B

D

*Stile Cap X3

*Channel TrimX3

* Please Note:Left and Right Hand variations supplied.

Bubble SealX1

Loose Stile

X1

Head & Cill ProfileX2

Top Adjustable BearingX2

Door Handle Assembly

X1

D4 D5

D6

Blade SealX2

Bottom SpringLoaded BearingX4

(actual size)

No.8 x 1” Pan Head Pozi Screws Cx8

Qty

No.8 x 1¾” Pan Head Pozi Screws (actual size)

(actual size)

(actual size)

Ax6

Qty

Wall PlugsBx6

Qty

No.8 x ⅜” Pan Head Pozi ScrewsDx9

Qty

(actual size)

Screw CupEx9

Qty

Loose Screws & Fittings Supplied

Fix through pre-drilled holes

C

1.1

Fix through pre-drilled holes

Tip: Assemble frame vertically.*

1.2

Ensure Glass Side Panels are located in pre-fitted glass holders as shown.!

Inside View

Tip: When inserting screws, apply a small amount of oil to the screw thread to allow easier fixing.

*

C

2.1

2.2

2

Note: Two different Blade Seal lengths supplied. Use shorter of the two seal lengths at this stage.

! Tip: To push fit Side Panel Blade Seal, start at the bottom and work up.*

Inside View

Inside View

Inside View

3.1

3.2

Plan View

3

Mark Wall Channel position.

IMPORTANT NOTEEnsure glass is positioned straight and is parallel with tray. DO NOT push frame fully into channel, allow a suitable gap to ensure adjustment and fixing.

!

Do NOT fix Wall Channels at this stage. Ensure Wall Channel is level and mark position.

!

4

4.1

6mm dia. holes with drill bit suitable for wall surface

Mark position of pre-drilled Wall Channel fixing hole

A

4.2

4.3

B

Fix through pre-drilled Wall Channel fixing hole

Wall plugs supplied are for solid walls only. Ensure correct wall plug for wall type is used. If in doubt, seek professional advice.

!Position Wall Channel on wall as shown, ensure Wall Channel is fixed level. !Tip: When drilling tiles apply masking tape to surface to stop drill bit slipping.*

Inside View

Leave 3mm gap for trim strip

D

Tip: When inserting screws, apply a small amount of oil to the screw thread to allow easier fixing.

*

Inside View*3mm dia. holes through pre-drilled holes using HSS drill bit

6.1*

6.2E

Ensure glass is positioned straight and is parallel with tray. !

6Inside View

Plan View

IMPORTANT NOTEEnsure glass is positioned straight and is parallel with tray. !

5

Tip: When positioning frame, hold frame and position bottom corners first.*

D

E

8

8.1 8.2

8.3

Top Adjustable Bearing Fixing Preparation

Inside View

Please Note: Top Adjustable Bearings are supplied fully assembled. Disassemble part prior to fixing.!Please Note: Top adjustable Bearing and Bottom Spring Loaded Bearing variations. Use TOP ADJUSTABLE BEARING only.!

7

Inside View

Inside View

Tip: When inserting screws, apply a small amount of oil to the screw thread to allow easier fixing.

*

7.1*

7.2

*3mm dia. holes through pre-drilled holes using HSS drill bit

Ensure glass is positioned straight and is parallel with tray. !

9.1 9.2

9.3

Please Note: Bottom Spring Loaded Bearings are supplied fully assembled. Disassemble part prior to fixing.!Please Note: Bottom Spring Loaded Bearing and Top adjustable Bearing variations. Use BOTTOM SPRING LOADED BEARING only.!

Bottom Spring Loaded Bearing Fixing Preparation

Inside View

9

Inside View

10Inside View

10.1

Please Note: Door Handles are supplied assembled. Disassemble part and then re-assemble as shown. DO NOT overtighten.

!

Tip: Locate bearing wheels on the top rail first.*

Inside View

12

Inside View

11Inside View

Note: Two different Seal lengths supplied. Use longer of the two versions at this stage.

!

Ensure Door Blade Seal is fitted with blade facing away from enclosure (As Shown).!Tip: Push fit Door Blade Seal, start at the bottom and work up.*

11.1

13.1

13.2

Inside View

14

Tip: When door is correctly located, door position can be adjusted up and down using Top Bearing adjustment screws (above).

*Ensure free movement of door. Adjust to suit.!

Inside View

Inside View

Bottom bearings are sprungloaded. Push them down so they fitinto the bottom cill rail.*

13

Inside, Underside View

Inside View

15Inside View

First locate channel trims and pushuntil they snap into place. Next fitcover caps.*

16

Apply Silicone Sealant (not supplied).!Only apply silicone sealant to the inside verticals where the WallChannels meet the wall.!

150mm

150mm 150mm

17

Apply Silicone Sealant (not supplied).!Product Care: Use a non-abrasive cleaner. Water marks may be removed with a proprietary limescale remover or household vinegar.

*

Notes:Notes:

Notes:Notes:

• Check that the tray has been installed correctly and that it is level (Fig. A) Tiled down onto and sealed to the manufacturer’s guidelines. Please Note: All product is supplied without a tray.

• Ensure the product is fitted to a non-porous surface eg ceramic tiles & waterproof panels.• Check that the wall surface is flat.• Unpack and check the product is complete and undamaged.

• Handle all glass with care - support on cardboard to avoid risk of breakage.• This product is heavy and requires 2 people to carry and install it.• When drilling walls, check first for hidden pipes and cables.• All glass is toughened – it cannot be reworked or replaced by ordinary glass.• Use safety eyewear when drilling.• Use safety eyewear when handling glass.• Keep all small parts away from children.

Safety

• Please notify the retailer immediately of any damage or faults. The manufacturer cannot be held responsible for any installation costs that may arise from damaged or faulty product being installed.

• Please dispose of all packaging with due regard to the environment.

Disclaimer

Before You Start

Tools Required (not supplied)

Fig. A

Spirit Level Screwdriver Tape Measure

Junior Hacksaw

Pencil Utility Knife

Silicone Gun & Sealant Power Drill Suitable Drill Bits

6mm dia. *

3mm dia. HSS

* Ensure drill bit used is suitable for wall surface

• Fixings are supplied for solid walls only. Ensure that the correct fixings are used for the wall type – if in doubt seek professional advice.

• Ensure the area is clean, dry and dust free.• Read the instructions in full.• Have the correct tools available,

(See ‘Tools Required’ below).• It is recommended to situate the showerhead and

door adjacent to each other in order to allow any water spray to be on the side panel or upstanding wall.

We have taken great care to ensure that this product reaches you in perfect condition. However should any parts be damaged or missing please contact your point of purchase. This does not affect your statutory rights. In addition if you require replacement parts your point of purchase will be happy to assist.

• For smooth running of the door periodically lubricate runners with supplied silicone grease.

In-use and care recommendations

Parts & Fittings Supplied

Please notify the retailer immediately of any damage or faults. The manufacturer cannot be held responsible for any installation costs that may arise from a damaged or faulty product being installed.

!Keep small parts away from children!

D1

D2

Bi-fold DoorX1

No.8 x 1¾” Pan Head Pozi Screws (actual size)

(actual size)

(actual size)

(actual size)

Ax6

Qty

Wall PlugsBx6

Qty

No.8 x ⅜” Pan Head Pozi ScrewsCx6

Qty

Screw CupDx6

Qty

B

*Stile CapX2

Door Knob Assembly

X1

A

D1 D2

Loose Screws & Fittings Supplied

DC

ChannelTrim X2

Wall Channel X2

*Channel CapX2

* Please Note:Left and Right Hand variations supplied.

1.1

Please Note: Position one wall channel and mark. Ensure Wall Channel is level and in correct location to the tray. (If in doubt refer to illustration on step 2).

!

1.2 1.3

2

Ensure glass is positioned straight and is parallel with tray. !

Plan View

3.1

6mm dia. holes with drill bit suitable for wall surface

Mark position of pre-drilled Wall Channel fixing hole

3.2

3.3

3

Fix through pre-drilled Wall Channel fixing hole

B

A

IMPORTANT: Ensure Door is not twisted. For best results fix one side wall channel, and check door is level before continuing to fix second wall channel.

!Position Wall Channel on wall as shown, ensure Wall Channel is fixed level. !Wall plugs supplied are for solid walls only. Ensure correct wall plug for wall type is used. If in doubt, seek professional advice.

!Tip: When drilling tiles, apply masking tape to surface to stop drill bit slipping.*

Inside View

Leave 3mm gap for trim strip

5.1Inside View

4 *3mm dia. holes through pre-drilled holes using HSS

drill bit

D

C

4.1*

4.2

Tip: When inserting screws, apply a small amount of oil to the screw thread to allow easier fixing. *Ensure gap from the front of the

tray to the front of the enclosure is a equal size all the way around.!

Inside View

5

Inside View

Please Note: Door knobs are supplied assembled. Disassemble part and then reassemble as shown.

!

6

Apply Silicone Sealant (not supplied).!Only apply silicone sealant to the inside verticals where the Wall Channels meet the wall.!

7

First locate channel trims and push until they snap into place. Then fit cover caps.!

6.1

6.2

150mm

Apply Silicone Sealant (not supplied).! Product Care: Use a non-abrasive cleaner. Water marks may be removed with a proprietary limescale remover or household vinegar.

*

8