bible paper toys book 07 color

17
Paper Toys BIBLE Book 7 The Tomb The Easter Story

Upload: odette-mueller-dogan

Post on 11-Nov-2014

468 views

Category:

Documents


61 download

DESCRIPTION

for little children Bible toys

TRANSCRIPT

Page 1: Bible Paper Toys Book 07 Color

Paper ToysBIBLE

Book 7The Tomb

The Easter Story

Page 2: Bible Paper Toys Book 07 Color

Model designed by Didier Martin.Copyright © 2011 by Didier Martin

http://jacques-mylittlehouse.blogspot.com/

Bible Paper ToysThe Easter Story

Matthew 28, Mark 16, Luke 24, and John 20.

You can read the story of Easter in:

Page 3: Bible Paper Toys Book 07 Color

Bible Paper Toys - Book 7 - The Easter Story - The Tomb - page 1

inside wall of the tomb part 1

round stone for the entrance of the tomb part 1

Page 4: Bible Paper Toys Book 07 Color

inside wall of the tomb part 2Bible Paper Toys - Book 7 - The Easter Story - The Tomb - page 2

round stone for the entrance of the tomb part 2

Page 5: Bible Paper Toys Book 07 Color

outside tomb wall part 1

Bible Paper Toys - Book 7 - The Easter Story - The Tomb - page 3

Page 6: Bible Paper Toys Book 07 Color

outside tomb wall part 2

Bible Paper Toys - Book 7 - The Easter Story - The Tomb - page 4

Page 7: Bible Paper Toys Book 07 Color

outside tomb wall part 4

Bible Paper Toys - Book 7 - The Easter Story - The Tomb - page 5

Page 8: Bible Paper Toys Book 07 Color

outside tomb wall part 6

outside tomb wall part 5

Bible Paper Toys - Book 7 - The Easter Story - The Tomb - page 6

Page 9: Bible Paper Toys Book 07 Color

outside tomb wall part 3

Bible Paper Toys - Book 7 - The Easter Story - The Tomb - page 7

Page 10: Bible Paper Toys Book 07 Color

round stone for the entrance of the tomb part 3

Bible Paper Toys - Book 7 - The Easter Story - The Tomb - page 8

Page 11: Bible Paper Toys Book 07 Color

stone bed for inside the tomb

Bible Paper Toys - Book 7 - The Easter Story - The Tomb - page 9

Page 12: Bible Paper Toys Book 07 Color

ASSEMBLY INSTRUCTIONS

Tools needed• Small scissors. Small craft or manicure scissors work best. • Hobby knife. Put in a sharp new blade, such as X-acto #10 or #11 for best results. • Sturdy tweezers. Tweezers with rough edges or teeth will mar the surface of the pieces, so

findasetwithsmoothedges.• Straightedge or ruler. Preferably a metal one, to guide your knife in making a straight cut or

score. • Toothpicks or blunt dental tools for reaching into tiny corners and spreading drops of glue. • White glue. • Cutting surface. You can use a self-healing cutting mat, but a piece of cardboard will also

workfine.• “Dead” pen (no more ink) or blunt knife for scoring.

TIP: After cutting out the parts and folding the tabs, make sure the parts fit together before gluing them. Refer to the picture of the final model to see how the different parts fit together.

Print pages 1 through 9 on cardstock and follow the assembly instructions. Take your time and make sure all the parts line up properly before gluing. Just like anything else, it takes practice to get each modelexactlyright.Butyou’llfindthatthemoremodelsyouworkontheeasiertheybecome.

Cut lines

Mountain fold

Valley fold

Glue spot

ScoringScore the fold lines to make a crisp straight fold. It’s especially important for the smallest pieces to be scored before folding. To score, place a metal ruler along the fold line, and then press with a dull point along the fold line to compress the paper.

CAUTION• Be careful when using scissors or hobby knife.• Glue, scissors, and other tools may be dangerous to young children

so be sure to keep them out of the reach of young children.

CuttingUsually, a part of a card model is cut in two stages. First, the part is separated from the rest of the parts by cutting roughly around it with scissors. Don’t cut on the lines at this step. Once the part is separated, you can work on it without damaging other parts. Often, it’s best to do the scoringandfoldingbeforeproceedingtothefinecutting.Withsmallpartsandnarrowtabs,it’seasier to fold them neatly while there is still waste paper around the part.

Bible Paper Toys - Book 7 - The Easter Story - The Tomb - page 10

Page 13: Bible Paper Toys Book 07 Color

1

23

4

5

This model may seem complicated, but if you follow the steps below carefulyitisnotdifficult.Take your time and try out the different pieces before gluing them to understandhowtheyfit

together.

Start with “outside tomb wall part 1, 2

and 3.”

Then move on to “outside tomb wall part 4” to close

the top of the tomb.

Bible Paper Toys - Book 7 - The Easter Story - The Tomb - page 11

Page 14: Bible Paper Toys Book 07 Color

6

7

8

This is a view from inside the model. At this point, don’t be concerned about the strength of the model. As you add the

others parts the model will stand properly.

Now glue “outside tomb wall part 5 and 6” to the front of the tomb.

Here is a photo of thefinalmodelofthe exterior wall of

the tomb.

Bible Paper Toys - Book 7 - The Easter Story - The Tomb - page 12

Page 15: Bible Paper Toys Book 07 Color

9

10

11

Now for the inside of the tomb, glue together “inside wall of the tomb part 1 and 2.” Look

carefully, as some parts need the “valley fold.”

This will form a wall, next put together the “stone bed” and glue it against the inside wall

as in the photo.

Then glue this wall inside the tomb rock tofinishthetomb.

Bible Paper Toys - Book 7 - The Easter Story - The Tomb - page 13

Page 16: Bible Paper Toys Book 07 Color

12

13 Assembling the round stone for the entrance of the tomb: Glue the two

strips together to form the rim of the stone, then glue both sides of the stone in

place.

Bible Paper Toys - Book 7 - The Easter Story - The Tomb - page 14

Page 17: Bible Paper Toys Book 07 Color

http://jacques-mylittlehouse.blogspot.com/

Bible Paper ToysThe Easter Story - Book 7

Included in this book:• the tomb• the round stone at

the entrance