7/28/2019 bizhub_500_420_im

1/10

E-1

INSTALLATION MANUAL

50GE97220

MFP Machine

I. Outline of Installation Procedures for MFP Machine System

When installing the machine and associated as a system, follow the order shown on the upper.Note:

For the detailed installation procedures for each option, follow the instructions given in the correspondingInstallation Manual and perform the procedures correctly.

Once the Power Switch is turned on, do not turn off it until the installation work has been completed.

II. Installation space

Dehumidifier Heater 1C

PU-501

DK-501 PC-402

MFP Machine

PC-202

LU-201 Internal Heater (For LU)

FS-510

RU-502

OT-501FS-511

MT-501 SD-502JS-502

IC-204

OT-601

HD-505

MK-708

100100

680

590910

2400.5

708550200

1458

1150

1650

500

943420

700.5

Machine+Paper feed cabinet PC-402+Finisher FS-511+Large capacity unit LU-201(Relay unit RU-502)

(Unit: mm)

Applied Machines: 500/420MFP 50ppm/42ppm

7/28/2019 bizhub_500_420_im

2/10

E-2

III. How to carry the product

1. Hold the machine by the locations indicated by thearrows, and move it while keeping it horizontal.

IV. Accessory parts1. Photo conductor2. Developer3. Users guide (Except for Europe)4. Installation manual5. CD-ROM6. Front cover7. Drawer cover

8. Users guide holder9. Fall prevention leg10. Power cord (for some areas only)11. Power cord instruction (for some areas only)12. Nylon clamp13. SEMS II screw M4x50: 2 pcs.14. B tight screw M3x8: 2 pcs.15. S tight screw M3x8: 1 pc.16. TP screw M3x6: 1 pc.17. TP screw M3x8: 1 pc.Note:

The drawer cover and B tight screw M3x8(2 pcs)

are used for the paper feed cabinet or desk.

Note:

Lifting the machine in an awkward position ortransporting it in a poorly balanced position couldresult in personal injury. When transporting themachine, assign an adequate number of personsto the job and ensure that each person can take agood position of not being excessively loaded.(mass: approx. 100kg)

50GAIXC001SA

After unpacking, be sure to get rid of thepackaging materials and keep them out ofthe reach of children.Putting your head in the plastic bag involvesdanger of suffocation.

WARNING

7/28/2019 bizhub_500_420_im

3/10

E-3

V. Installation proceduresNote:

Do not plug in the power cord until instructed to do so.1. Visually check the appearance of the machine.2. Remove locking tapes and the protection cushion

from the machine and ADF.3. Remove the accessory parts.

4. Open the ADF and remove the glass protectingcushion and glass protection paper.

5. Remove the optics unit locking screw.

6. Remove protective materials from the bypasstray.

(1) Open the bypass tray and remove the interfer-ence protection cushions.

The optional paper feed cabinet is included in theimage.

50GEIXE001SA50GEIXE001SA

Note 2:

Open the cover indicatedin the circle and removethe protection cushion.

Note 1:

A protective material isunder the ADF paper feed tray.

Front door

Guide

tapes

Note:

Not taking guidetape till thereare instructions.

Remove

50GEIXE002SA

Original glass protecting paper

Original glass protecting cushions

50GEIXE004SA

Red paper

Optics unit locking screw

50GEIXE005SA

Interference protection cushions

7/28/2019 bizhub_500_420_im

4/10

E-4

(2) Remove locking tapes, locking material, andprotection cushions from the places shownbelow.

7. Remove the accessories and the locking tapefrom Tray 1 and 2, then remove the locking guidetape.(Europe: Users guide is not included.)

8. Remove the corona protecting pieces and lockthe fusing pressure lever.

(1) Open the right door, then open the conveyanceunit.

(2) Remove two corona protecting pieces on bothsides.

(3) Lower the fusing pressure lever to lock it.(4) Close the conveyance unit and right door.

9. Open the front door and remove the blade lockplate as shown below.

50GEIXE006SA

Lock piece

Protection cushions

00AAIXE000SA50GEIXE007SA

Tray 1

Tray 2

Guide tape

Guide tape

Accessories

Lock tape

(Locking tapes are under the accessories.)

50GEIXE008SA

Fusing pressue lever

Conveyance unitCorona protecting pieces

50GEIXE009SA

Lock tape

Blade lock plate

7/28/2019 bizhub_500_420_im

5/10

E-5

10. Supply the developing unit with developer.(1) Loosen one screw to draw out the developing unit.

(2) Release the two claws of the developing unitas illustrated below, and then remove thedeveloping unit cover.

(3) Pour the developer over the agitator screwevenly from the top of the agitator screw alongits entire length.

(4) Turn the developing gear in the direction of the

arrow, as illustrated below to coat the devel-oper around the developing roller completely.

Note:

Do not turn the developing roller gear in the oppo-site direction of the illustrated arrow.

(5) Attach the developing unit cover as illustratedbelow.

Note:

Be careful of deforming the scatter prevention sheet.

50GEIXE010SA

Developing unit

Developing unit

Developing unit cover

Claws

50GEIXE011SA

Developer

Agitator screw 50GEIXE012SA

Developing roller gear

Developing roller

50GEIXE013SA

Cover

Developing unit cover

Claws

Scatter preventionsheet

50GEIXE014SA

7/28/2019 bizhub_500_420_im

6/10

E-6

(6) Reinstall the developing unit to its original posi-tion. (1 screw)

Note:Be sure to set the developing unit on two rails asshown below, then slide it in place.

11. Install the front cover.(TP screw M3x6: 1pc.)

12. Close the front door.

13. Plug the ADF connector to the machine.14. Install the User's guide holder on the rear side of

the machine.

15. Install the drawer cover on the paper feed cabi-net or the desk in the position shown in the fig-ure below. (B tight screw M3x8: 2 pcs.)

16. If the LU-201 (large capacity unit) is not installed,install the fall prevention leg on the right side ofthe paper feed cabinet or the desk.

(1) Remove the locking tape and the cover fromthe fall prevention leg.

Developing unit

Rails

50GEIXE015SA

50GEIXE016SA

Front cover

TP screw M3x6

50GEIXE017SA

User's guide holder

ADF'sconnector

50GEIXE018SA

B-tight screws M3x8

Drawer cover

50GEIXE019SA

Cover

Lock tape

7/28/2019 bizhub_500_420_im

7/10

E-7

(2) Remove the right rear cover from the paper feedcabinet or the desk.(two screws)

(3) Install the fall prevention leg with two screwsincluded in the package in the location wherethe right rear cover is removed.(SEMS II screwM4x50: 2pcs.)

(4) Install the cover on the fall prevention leg.(TPscrew M3x8: 1pc.)

17. Plug the power cord into the AC jack at the rearof the machine, and secure the cord with a nylonclamp.(S-tight screw M3x8: 1pc.)

18. Open the front door, then set the toner bottle.(See explanation label on the front door.)

Note:

Make sure to set the toner bottle before per-forming the TCR adjustment. Before setting make sure to align the toner bot-

tle installation place.: Align the convex portionand the boss in the center.

19. Execute the TCR adjustment.Plug the power cord of the machine to the outlet,and turn on the machines main and sub powerswitches.

50GEIXE020SA

Right rear cover

50GEIXE021SA

SEMS II screwsM4x50

Fall prevention leg

50GEIXE022SA

Cover

TP screwM3x8

Step

1. Press the [Utility/Counter] key.

2. On the [Utility/Counter] screen, touchDetails and enter the following sequence[Stop]+[0]+[0]+[Stop]+[0]+[1] to enter [ServiceMode].

3. Touch Imaging Process Adjustment.

4. Touch TCR Adjustment.

5. Press the [Start] key.automatically stops with the messageon the screen.

50GEIXE023SA

Nylon clamp

S-tight screw M3x8

50GEIXE024SA

Center boss

Convex portion

7/28/2019 bizhub_500_420_im

8/10

E-8

20. Execute the Non-image area erase check.

21. Execute the various settings.(1) Enter installation date.

(2) Enter service telephone number & fax number.

(3) Set date and time.

Step

1. Touch OK to return to the [Service Mode]screen.

2. Touch Machine.

3. Touch Non-Image Area Erase Check.Note:

Fully open the ADF. Do NOT place anything on the original

glass. Clean the original glass if dirty.

4. Follow the on-screen instructions and pressthe [Start] key.

5. After the adjustment, if any message otherthan is displayed, deal as follows.Error 1:Handling method 1:When copy originals that have a dark back-ground are frequently copied in non-imagearea erase function, install the machine in alocation where less external light gets in(darker) than the present location, and per-form the non-image area erase check again.Error 2:Handling method 2:If the non-image area erase function is fre-quently used, install the machine in a locationwhere less external light gets in (darker) thanthe present location, and perform the non-image area erase check again. At this time,when there is a bright light source such as afluorescent light installed directly above themachine, reconsider the installation location,or take some measures to shield the lightsource and perform the non-image areaerase check again.

Step

1. Touch OK to return to the [Service Mode]screen.

2. Touch System 1.3. Touch Install Date.

4. On the [Install Date] screen, press the [C] key,and use the numeric keypad to enter the set-ting date in the order of year, month, and day.

Note:Enter four digits for the year, and two digitsfor the month and the day.

5. Make sure to touch Entry.The installation date will be updated to thecurrent setting.

Step

1. Touch END to return to the [Service Mode]screen.

2. Touch Tel/Fax Number.

3. On the [Service Telephone/Fax Number Set-ting] screen, use the numeric keypads to enterthe telephone number.

4. Touch FAX.

5. Use the numeric keypads to enter the faxnumber.

6. Make sure to touch END.

7. Turn the sub power switch off.

Step

1. Turn the sub power switch ON.

2. Press the [Utility/Counter] key.

3. On the [Utility/Counter] screen,touch Administrator Setting.

4. On the [Administrator Certification] screen,enter the administrator password 12345678(factory default) and touch OK.

5. On the [Administrator Setting] screen,touch System Setting.

6. Touch Date/Time Setting.

7. On the [Date/Time Setting] screen,

make sure that the date and time are correct.If not, set the right date and time. Touch thekey for the item you want to set (year/month/ day/hour/minute), and then press the [C] key.

8. Use the numerical keypad to enter the num-bers.

9. Make sure to touch OK.The date and time will be updated to the cur-rent setting.

7/28/2019 bizhub_500_420_im

9/10

E-9

VI. ADF angle changeThe opening angle of the ADF can be set at 70 or 40degrees. Set the angle according to the customersrequest.Default setting at installation: 70 degrees.1. Remove the screw of the angle adjustment plate

on the rear of the ADF. Then, turn it upside downand tighten the screws.

2. Perform the same procedures for the other plate.

VII. Operation check1. Load paper in the trays and make sample copies.2. Inspect the copy quality with the test chart fed

from the ADF.

Check items: Side edge, resist loop value, lead-ing edge, etc.

Adjustment: Refer to the Service ManualADJUSTMENT/SETTING of Mainbody of Field Service.

3. Affix the Tray size label of specified size to eachtray (NO.1 to NO.2).

VIII. CS Remote CareRefer to the Service Manual ADJUSTMENT/SET-TING of Main body of Field Service.

IX. Network Connection and Settings[Connecting network cable]1. Connect a network cable (category 5 or 5E) to the

connector port.2. Check if the connector port LED lights (LED1 and

LED 2) are lit.LED 1 (top): Lit if connected to the LINK net-

work.

LED 2 (bottom): Flashes according to the con-nection status of the ACTnetwork.

[IP address assignment]Note:

User networks and the PC environment are usu-ally managed by technical administrators. Whendoing the following setup, be sure to check withthe person in charge to get approval and proceedunder that persons supervision.

50GEIXE025SA

70 degrees 40 degrees

Angle adjustment plates

Screws

Step

1. Press the [Utility/Counter] key.

2. Touch Administrator Setting.

3. Enter the administrator password 12345678(factory default) and touch OK.(You can switch between upper case andlower case letters with the Shift key.)

Note:If an administrator password has been setalready, enter the current password andtouch OK.

4. Touch Network Setting.

5. On the screen that appears when the TCP/IPSetting touched, set the following items.

TCP/IP Setting: Select ON. DHCP Setting: Select OFF. IP Address: IP address of the machine Subnet Mask:

subnet mask of network to be connectedto

Default Gateway:IP address of the default gateway

6. Touch OK to return to the Administrator Set-

ting screen.7. Touch Network Setting.

8. Touch Network setting to check if it is ON.If OFF is selected, change it to ON.

9. Touch OK.

10. When the setup is completed, be sure to turnoff then turn on the main and sub powerswitches. (Otherwise the new settings will notbe registered. When turning the main and subpower switches back on, wait for 10 secondsor more after turning them off.)

7/28/2019 bizhub_500_420_im

10/10

E-10

[Confirming network connection by pinging]

Step

1. Turn on the main and sub power switches ofthe machine.

2. Press the [Utility/Counter] key.

3. Touch Administrator Setting.

4. Enter the administrator password. (See step3 in [IP address assignment].)

5. Touch Network Setting.

6. Touch Detail Setting.

7. Touch PING Confirmation.

8. Touch Host Address, enter the valid IPaddress or host name, and touch OK.

9. Touch Check Connection to send a ping.

10. After pinging is complete, a result will appear.If the test is unsuccessful, or a similar message will appear.=> In this case, check if the address or host

name is correct and the network is prop-erly connected, and try sending a pingagain until the result is successful.