bmw f650 funduro sprag clutch

6
BMW F650 FUNDURO REPLACE/REPAIR FREEWHEEL/ONE WAY CLUTCH/ SPRAG CLUTCH. Equipment required. No 17 Spanner. No 5 Allen bit or key. No 30 Socket. Impact driver. Flat Screwdriver. No 20 Socket. Ratchet spanner. Special tool Puller BMW 12 5 510 (for removing magnet rotor) Locktite 648 or medium strength. 1200 Sanding paper. No 24 Spanner. No 9 socket. Oil pan or drip tray. +- 1 Litre oil. Oil seal spring. White spirit. Acetone. Method. 1. Drain oil from sump. No 17 spanner. (Fig 1) 2. Allow all oil to drain. 3. Check aluminium crush washer on sump plug for damage, replace if necessary. 4. Loosen Allen bolts on Right Engine housing. 10 in total. Using no 5 Allen bit or key. (Fig 2) Fig 1

Upload: fires-jansen-van-vuuren

Post on 03-Apr-2015

2.062 views

Category:

Documents


2 download

DESCRIPTION

How to dismantle, repair and assemble the Sprag Clutch on the BMW F650 Funduro.

TRANSCRIPT

Page 1: Bmw f650 Funduro Sprag Clutch

BMW F650 FUNDURO

REPLACE/REPAIR FREEWHEEL/ONE WAY CLUTCH/ SPRAG CLUTCH.

Equipment required.

• No 17 Spanner. • No 5 Allen bit or key. • No 30 Socket. • Impact driver. • Flat Screwdriver. • No 20 Socket. • Ratchet spanner. • Special tool Puller BMW 12 5 510 (for removing magnet rotor) • Locktite 648 or medium strength. • 1200 Sanding paper. • No 24 Spanner. • No 9 socket. • Oil pan or drip tray. • +- 1 Litre oil. • Oil seal spring. • White spirit. • Acetone.

Method.

1. Drain oil from sump. No 17 spanner. (Fig 1) 2. Allow all oil to drain.

3. Check aluminium crush washer on sump plug for damage, replace if necessary. 4. Loosen Allen bolts on Right Engine housing. 10 in total. Using no 5 Allen bit or key. (Fig 2)

Fig 1

Page 2: Bmw f650 Funduro Sprag Clutch

5. Loosen sprocket cover and remove. (Fig 3 and 4)

6. Remove oil breather pipe. (Fig 5)

Fig 4

Fig 3

Fig 2

Page 3: Bmw f650 Funduro Sprag Clutch

7. Remove right engine housing cover and rest on footpeg. Ensure gasket is not damaged and replace if necessary. (Fig 6)

8. Remove washer from pin. (Fig 7)

9. Loosen hex nut with no 30 socket and impact driver. (Fig 8) For assembly use loctite.

Fig 5

Fig 6

Fig 7

Page 4: Bmw f650 Funduro Sprag Clutch

10. Ensure 1st gear is engaged.

11. Use puller BMW 12 5 510 (this is a homemade puller) and no 22 socket to remove Magnet

rotor (Fig 9) 12. Ensure Lock key is there. (Fig 10)

Fig 8

Fig 9

BMW 12 5 510

Page 5: Bmw f650 Funduro Sprag Clutch

13. Place magnet rotor on table with freewheel facing up. (Fig 11)

14. Loosen 4 nuts with no 9 socket. (Fig 12)

15. Remove cover plate and clean with white spirits. (Fig 13) For assembly use loctite.

Fig 10

Fig 11

Fig 12

Page 6: Bmw f650 Funduro Sprag Clutch

16. Take note of the arrow and direction it show (Fig 14)

17. Remove free wheel. Take note of roller bearings and their position (of the lobes) as well as the spring, if spring is broken the roller bearings will fall out so take care if you remove the free wheel from the magnet rotor. (Fig 15)

18. Now install the oil seal spring in the free wheel or new free wheel (sprag clutch) and then

assemble in the reverse of the dismantling, remember to use Loctite 648 or medium strength.

Fig 13

Fig 14

Fig 15