brochure rpc transducers data sheet

2
e Energy Flows rough Us™ Luin Automation offers RPC transducers for all the different pumping unit types. e transducer selection allows the user to choose the accuracy of the system and consider the long- term maintenance requirements. Each transducer is designed to interface with Luin RPCs and is manufactured to Luin’s quality standards. Rod Pump Control Transducers for use with Lufkin Well Manager and others Load Cell 1 Motor and Crank Hall Effect Transducers Lufkin Well Manager System 2 1 3 4 2 2 Rated capacity: 30K or 50K pounds (specify) Overload rating without damage: 200% rated capacity Weight: 8.5 pounds Output (mV/V): 2.0 ±1% Operating temperature range: –40°F to 175°F Transient voltage protection: MOV to case Factory calibrated Unipolar hall effect switch Magnets mounted on crank arm and motor shaft Input voltage range: 4.5 to 24 Vdc Output open collector: sink 25 mA max Typical sensitivity: 350 gauss Operating temperature range: –40°C to 85°C LUFKIN.COM/AUTOMATION OF11-0004R00

Upload: mamerhet

Post on 24-Jan-2016

218 views

Category:

Documents


0 download

DESCRIPTION

Brochure RPC Transducers Data Sheet

TRANSCRIPT

Page 1: Brochure RPC Transducers Data Sheet

The Energy Flows Through Us™

Lufkin Automation offers RPC transducers for all the different pumping unit types. The transducer selection allows the user to choose the accuracy of the system and consider the long-term maintenance requirements. Each transducer is designed to interface with Lufkin RPCs and is manufactured to Lufkin’s quality standards.

Rod Pump Control Transducers

for use with Lufkin Well Manager™ and others

Load Cell1

Motor and Crank Hall Effect Transducers

Lufkin Well Manager System

2

1

3

4

2

2

Rated capacity: 30K or 50K pounds (specify)Overload rating without damage: 200% rated capacityWeight: 8.5 poundsOutput (mV/V): 2.0 ±1%Operating temperature range: –40°F to 175°FTransient voltage protection: MOV to caseFactory calibrated

Unipolar hall effect switchMagnets mounted on crank arm and motor shaftInput voltage range: 4.5 to 24 VdcOutput open collector: sink 25 mA maxTypical sensitivity: 350 gaussOperating temperature range: –40°C to 85°C

LUFKIN.COM/AUTOMATIONOF11-0004R00

Page 2: Brochure RPC Transducers Data Sheet

©2011 Lufkin Industries, Inc. All rights reserved. OF11-0004R00

LUFKIN WELL MANAGER™ Rod Pump Control Transducers

Ratiometric electronic dynometerSupply voltage range: 5–16 VdcSupply current: 3 milliampsOutput: 30 mV/degreeLinear range: ±45 degrees

Load Cell Cable Options

Beam TransducerWheatstone bridge circuitGauge section thickness: 0.030 in.Input impedance: 350 ohm/263 ohmInput voltage range: 5–10 VdcOutput with 8 Vdc excitation (per installation)Offset range: 0.32 to 32 mVdcSensitivity: 2 mV/V increase with axial pull change from 500 to 1000 lbWeld mount to top of walking beamField calibration required

Clamp-On Beam TransducerSpecs same as weld-mounted beam transducerClamp-on mount to edge of walking beam flange

Automation Headquarters 811 Willow Oak Drive Missouri City, Texas 77489

(281) 495-1100 Fax: (281) 495-6333E-mail [email protected] for additional locations and information.

Contact Lufkin Automation E-mail: [email protected]

Inclinometer3 101TL Weld-Mounted (Reft) and Clamp-On (Right) Transducer4

Break AwayArmoredCoiledMolded

LUFKIN.COM/AUTOMATION