cab inter ext cables mgw rnc

8/10/2019 Cab Inter Ext Cables MGW RNC

1/90

Cabinet Interfaces and External

Cables of MGW and RNC

DN0127056Issue 9-4 en draft

# Nokia Siemens Networks 1 (90)


2/90

The information in this document is subject to change without notice and describes only theproduct defined in the introduction of this documentation. This document is not an officialcustomer document and Nokia Siemens Networks does not take responsibility for any errors oromissions in this document. This document is intended for the use of Nokia Siemens Networkscustomers only for the purposes of the agreement under which the document is submitted. Nopart of this documentation may be used, reproduced, modified or transmitted in any form ormeans without the prior written permission of Nokia Siemens Networks. The documentation hasbeen prepared to be used by professional and properly trained personnel, and the customerassumes full responsibility when using it. Nokia Siemens Networks welcomes customercomments as part of the process of continuous development and improvement of thedocumentation.

The information or statements given in this documentation concerning the suitability, capacity orperformance of the mentioned hardware or software products are given as is and all liabilityarising in connection with such hardware or software products shall be defined conclusively andfinally in a separate agreement between Nokia Siemens Networks and the customer.

IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THISDOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL,DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES SUCH AS BUTNOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESSOPPORTUNITY OR DATA, that might arise from the use of this document or the information in it.

THE CONTENTS OF THIS DOCUMENT ARE PROVIDED "AS IS". EXCEPT AS REQUIREDBY APPLICABLE MANDATORY LAW, NO WARRANTIES OF ANY KIND, EITHER EXPRESSOR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OFMERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT,ARE MADE IN RELATION TO THE ACCURACY, RELIABILITY OR CONTENTS OF THISDOCUMENT. NOKIA SIEMENS NETWORKS RESERVES THE RIGHT TO REVISE THISDOCUMENT OR WITHDRAW IT AT ANY TIME WITHOUT PRIOR NOTICE.

This document and the product it describes are considered protected by copyrights and otherintellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark ofNokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respective owners,and they are mentioned for identification purposes only.

Copyright Nokia Siemens Networks 2008. All rights reserved.

2 (90) # Nokia Siemens Networks DN0127056Issue 9-4 en draft

Cabinet Interfaces and External Cables of MGW and RNC


3/90

Contents

Contents 3

List of tables 5

List of figures 7

Summary of changes 9

1 Cabinet interfaces and cabling overview 131.1 Power supply interfaces 151.2 Interfaces from the front of the plug-in units 16

1.3 Interfaces from the back interface units 171.4 Interfaces from the cabling cabinet panels 201.5 Network Management Unit (NEMU) and service terminal interfaces 23

2 Network interfaces 252.1 PDH/TDM connector panels for E1 interfaces 252.1.1 CPETS-G, CPETS-E and CPETS 272.1.2 CPETC-E and CPETC-B 292.1.3 BIE1T-A, BIE1T and BIE1C 312.1.4 E1T48-A and E1C48-A 312.2 STM-1/OC-3 interfaces 322.2.1 Front panels of the NP8S1/-A/-B, NI4S1-B, IW1S1A and IW1S1 plug-in

units 322.2.2 Connector panel CPLC36 352.2.3 Connector panel CPRLC-B 362.3 LAN/Ethernet interfaces 372.3.1 Front panel of the NP2GE/-A plug-in unit 382.3.2 Front panel of the IPFGE plug-in unit 402.3.3 Front panels of the ESA24 and ESA12 plug-in units 422.3.4 Connector panel CPLAN-A 43

3 Maintenance interfaces 453.1 NEMU-specific maintenance interfaces 453.1.1 VDU (VGA) interface pinout 463.1.2 USB interface pinout 463.1.3 Keyboard and mouse pinout 473.1.4 SCSI interface pinout 473.1.5 LAN interface pinout 483.2 Service terminal interface 49

4 Connector panels for external alarm and synchronisationinterfaces 51

4.1 CPAL/-A and CPSAL/-B for alarm interfaces 514.2 CPSY-A, CPSY-B, CPSY and CPSAL/-B for synchronisation

interfaces 554.2.1 External inputs and outputs 57



Contents


4/90

5 Requirement specification for external cables 595.1 E1 and T1 balanced (symmetrical) PCM 595.2 E1 unbalanced (coaxial) cables 625.2.1 E1 unbalanced (coaxial) cables with the CPETC-E panel 625.2.2 E1 unbalanced (coaxial) cables with the BIE1C panels 645.2.3 E1 unbalanced (coaxial) cables with the E1C48-A or CPETC-B panel 655.3 Alarm output to EXAU/-A 675.4 Alarm input cable 715.5 Voltage-controlled alarm input 745.6 Current-controlled alarm input 775.7 Asymmetrical external synchronisation 795.8 Symmetrical external synchronisation 805.9 10Base-T/100Base-TX 835.10 1000Base-T 84

5.11 Optical STM-1 865.12 1000Base-LX (optical) 875.13 Reference standards and directions 89




5/90

List of tables

Table 1. Interfaces at the NP2GE/-A plug-in unit 39

Table 2. Interfaces at the IPFGE plug-in unit 41

Table 3. Interfaces at the ESA24/ESA12 units 42

Table 4. Interfaces on the NEMU units 45

Table 5. SVGA interface pinout (D15) 46

Table 6. USB interface pinout (4 pins) 46

Table 7. Keyboard and mouse pinout (6 pins) 47

Table 8. SCSI interface pinout (D68) 47

Table 9. LAN/Ethernet interface pinouts (RJ-45) for CPU, AL2S, CDSP and ESA24/ESA12 plug-in units 48

Table 10. Service terminal interface pinout (RJ-45) 49

Table 11. Voltage-controlled alarm inputs 1 (D37) 52

Table 12. Voltage-controlled alarm inputs 2 (D37) 53

Table 13. Current-controlled alarm inputs (D25) 53

Table 14. Alarm outputs to the External Alarm Unit (EXAU/-A) (D25) 54

Table 15. Alarm outputs (D37) 55

Table 16. External synchronisation inputs and outputs 57

Table 17. Synchronisation interface pinout (RJ-45) 57

Table 18. Synchronisation (OUT 2M) interface pinout (RJ-45) 58

Table 19. Cable CNIA E1 (120) component codes 60

Table 20. Cable CNIS T1 (100 ) component codes 60

Table 21. Cable CNIB (120) component codes 60

Table 22. RJ-45 connector pinouts (CNIA/CNIS) 60

Table 23. RJ-45 connector pinouts (CNIB) 61

Table 24. Component codes for the unbalanced (coaxial) CPRD cable 63

Table 25. D37 connector pinouts 64

Table 26. Component codes for unbalanced (coaxial) cable 65

Table 27. Component codes for unbalanced (coaxial) cable 66



List of tables


6/90

Table 28. Cable CNDC (version A01) component codes 68

Table 29. Cable CNDC (version A02) component codes 68

Table 30. Connector pinouts for a cable from CPSAL/-B to EXAU/-A or EXAU-A 1 toEXAU-A 2 with a direct cable 69

Table 31. Connector pinouts for a cable from EXAU-A 1 to EXAU-A 2 with acrossover cable 70

Table 32. Component codes for alarm output cable 72

Table 33. Connection pinouts for voltage-controlled alarm input 72

Table 34. Component codes for voltage-controlled alarm input cable 75

Table 35. Connection diagram for voltage-controlled alarm input 75

Table 36. Component codes for cable CNDC 77

Table 37. Connection diagram for current-controlled alarm input 78

Table 38. Component codes for asymmetrical external synchronisation cable 80

Table 39. Cable CNIA E1 component codes (120, receive and transmit signalsconnected) 81

Table 40. 64K / 2M / 1.5M symmetrical synchronisation input connector pinouts 81

Table 41. 2M / 1.5M symmetrical synchronisation output connector pinouts 81Table 42. Component codes for CNIX (cross-connected) or CNI (straight) cable 83

Table 43. Cross-connected cable 83

Table 44. Connector pinouts 85

Table 45. Cable types for single-mode optical cables 87

Table 46. Cable types for single-mode optical cables 89




7/90

List of figures

Figure 1. External interfaces of the MGW 14

Figure 2. External interfaces of the RNC 15

Figure 3. Interfaces from the front of the plug-in units of the MGW and RNC (IPFGEand IW1S1/A used in MGW only) 17

Figure 4. Interfaces from the back interface units of the equipment cabinet: CPSY-A(clock TSS3 0), CPSY-B (clock TSS3 1) and CPAL-A 18

Figure 5. Interfaces from the back interface units of the equipment cabinet: CPRLC-B, BIE1C, BIE1T, and BIE1T-A 20

Figure 6. Cabling cabinet panels 22

Figure 7. Network interfaces on the NEMU plug-in units MCPC2/-A and MCP18/-B 23

Figure 8. Back interface unit and connector panel equipping options 26

Figure 9. Connector panel CPETS-G for the cabling cabinet 27

Figure 10. Connector panel CPETS-E for the cabling cabinet 28

Figure 11. Connector panel CPETS for the cabling cabinet 29

Figure 12. Connector panel CPETC-E for the cabling cabinet 30

Figure 13. Connector panel CPETC-B for the cabling cabinet 31

Figure 14. E1T48-A (upper) and E1C48-A (lower) connector panels for the IC186equipment cabinet 32

Figure 15. Front panel of the NP8S1 plug-in unit 33

Figure 16. Front panel of the NI4S1-B plug-in unit 34

Figure 17. Front panel of the IW1S1/A plug-in unit 35

Figure 18. Connector panel CPLC36 in the cabling cabinet 36

Figure 19. Equipping the connector panel CPRLC-B 37

Figure 20. Front panel of the NP2GE plug-in unit 39

Figure 21. Front panel of the IPFGE plug-in unit 41

Figure 22. Front panel of the ESA24 plug-in unit 42

Figure 23. Connector panel CPLAN-A 43

Figure 24. Connector panels CPAL/-A and CPSAL/-B for alarm interfaces 52

Figure 25. Connector panels CPSY-A, CPSY-B, CPSY and CPSAL/-B for alarm and

synchronisation interfaces 56



List of figures


8/90

Figure 26. Example of CNIA cable assembly 61

Figure 27. Connecting a PCM E1 cable to a connector, CNIS (example) 62

Figure 28. D37 connector body with unbalanced (coaxial) contacts (1=pin,2=ring) 63

Figure 29. Example of E1 multicoaxial cable with SMB connectors 65

Figure 30. Example of E1 multicoaxial cable with BT43 connectors 67

Figure 31. Example of alarm cable to the EXAU/-A 71

Figure 32. Example of alarm output cable 74

Figure 33. Example of voltage-controlled alarm input cable 76

Figure 34. Example of current-controlled alarm input cable 79

Figure 35. Example of asymmetrical external synchronisation cable 80

Figure 36. Example of symmetrical external synchronisation cable 82

Figure 37. Example of LAN cable 84

Figure 38. Example of LAN cable 85

Figure 39. Example of a single-mode optical cable 87

Figure 40. Example of a single-mode optical cable 89




9/90

Summary of changes

Changes between document issues are cumulative. Therefore, the latest

document issue contains all changes made to previous issues.

Changes for issue 9-4

Added new plug-in unit variants:

. MX1G6-A, ATM multiplexer 1.6 Gbits/s variant A. New variant for

MXU.

. NP2GE-A, network interface and processing 2X1000Base-T/LX

variant A

. NP8S1-A/-B, network interface and processing 8xSTM-1 variant A

or B.

Some corrections and editorial changes.


Some editorial changes and minor corrections.


Two new panels to ETSI configuration introduced:

. BIE1T-A back interface panel

. CPETS-G connector panel

A new external site cable CNIB for the new panel types BIE1T-A and

CPETS-G introduced.



Summary of changes


10/90


11/90

Five new connector panel types introduced: CPAL-A, CPSY-A, and CPSY-

B for the rear of the cabinet, as well as the PDH/TDM connector panelsCPETS-E, and CPETC-E added.

Two new cables introduced: the external CPRD cable and the internal

CPSM cable.


Added information on the RoHS-compliant External Alarm Unit EXAU-A.SectionAlarm output to EXAU/-A updated.



Summary of changes


12/90




13/90

1 Cabinet interfaces and cabling overviewCabinet Interfaces and External Cables of MGW and RNCcontains

information on the network interfaces and cables for IPA2800 networkelements, namely Multimedia Gateway (MGW) and Radio Network

Controller (RNC). This document applies to all releases of both MGW and

RNC.

The external cables of the MGW and RNC connect the network element to

its environment, the mobile network it is used in. The MGW and RNC

network elements have the following interfaces to the environment:

. Power supply interfaces

. PDH/E1 T1 interfaces

. SDH/STM-1 OC-3 interfaces

. External synchronisation and alarm inputs and outputs

. LAN/Ethernet interfaces

. Service terminal interfaces from various plug-in units (for temporary

service operations; not covered by this manual)

. Interfaces of the Network Management Unit (NEMU) to accessoriesand peripherals: mouse, keyboard, and VDU

The external cables connect to the front panels of the plug-in units, to theback interface units at the rear of the equipment cabinets, or to the

connector panels in the cabling cabinet.

For more information, see the Cable Lists, Equipment Lists, Installation

Site Requirements for MGW and RNCand Engineering Descriptions.



Cabinet interfaces and cabling overview


14/90

MGW

Figure 1. External interfaces of the MGW

External timing

- 2.048 MBIT/s- 2.048 MHz- 64 kHz +8 kHz- 1.544 MHz

Service terminal RS232

-48V, 120A

NEMU- Ethernet 10/100 Mbit/s- SCSI

- USB- serial ports- keyboard, mouse- monitor (SVGA)

DN02179402

External alarms- general current/voltage outputsvoltage controlled inputscurrent controlled inputs

MGW

Network interfaces Operating interfaces

EXAU, EXAU-A- alarm indicator lamp panel

Ethernet10/100 Mbit/s

- STM-1/ OC-3- E1 /T1/JT1 (IMA)

Iu

ATM Core

ATM

A-interfacePSTN

IWF

TDM

- E1/T1/JT1

- STM-1/OC-3

H.248 controlIP Core /userplaneSIGTRAN

IP

- Ethernet

AterTDM

- E1/T1/JT1- STM-1/OC-3




15/90

RNC

Figure 2. External interfaces of the RNC

1.1 Power supply interfaces

The MGW and RNC operate on a -48V DC supply system. The voltage

limits are -40V DC to -57V DC. Each equipment cabinet has two mutually

redundant power entry connectors. Power feed cables can be routed

through from the top or bottom of the cabinet.

When using the CPD120-A cabinet power distributor, the maximum

current is 120A per cabinet, the maximum thickness of the power supply

cable is 70 mm2, and the maximum voltage drop is 1.5V.

SDH

STM-1

PDHE1/T1/JT1

ATM

ATM

Network interfaces

DN01128587

RNC

Operating interfaces

-48V, 120A

External alarms:

general current/voltage outputsvoltage-controlled inputscurrent-controlled inputs

EXAU, EXAU-A:alarm indicator lamp panel

NEMU:printer, monitor, keyboard, mouse

Ethernet:

10/100 Mbit/s

Service terminal RS232

External timing

2.048 Mbit/s or2.048 MHz64 kHz + 8 kHz1.544 MHz





16/90

When using the CPD80-B/-A cabinet power distributor, the maximum

current is 80A per cabinet, the maximum thickness of the power supplycable is 50 mm2, and the maximum voltage drop is 1.5V.

1.2 Interfaces from the front of the plug-in units

The front panels of the plug-in units house several connectors:

. STM-1/OC-3 interfaces from NP8S1/-A/-B (NPS1P/NPS1), NI4S1-B

(NIS1P/NIS1) and IW1S1/A (IW1SE, IWS1T; used in MGW only)

.

Optical LAN 1000 BASE-LX (NPGEP/NPGE), IPGOP), electricalLAN 1000 BASE-T (NPGEP/NPGE), IPGEP), and electrical LAN

100 BASE-T (IPFEP) interfaces from IPFGE (IPNIUP used in MGW

only)

. LAN 100 BASE-T interface(s) from the ESA24 plug-in unit (two front

panel connectors for external use)

. LAN 100 BASE-T interface(s) from the ESA12 plug-in unit (twoupper front panel connectors for external use)




17/90

Figure 3. Interfaces from the front of the plug-in units of the MGW and RNC

(IPFGE and IW1S1/A used in MGW only)

1.3 Interfaces from the back interface units

It is possible to route cables to the environment directly from the back

interface units of the equipment cabinet, when the network element does

not include a cabling cabinet.

LAN

Serviceterminal

ESA24

100BASE-T

LAN(not used)

Serviceterminal

IPFGE

1000BASE-T

1000BASE-LX

STM-1

Serviceterminal

NI4S1-B

DN02179683

LED

LAN (not used)

Service terminal

STM-1

STM-1 Redundant

IW1S1/A

NP2GE

Service terminal

1000BASE-LX

1000BASE-T

NP8S1

Service terminal

STM-1





18/90

. CPSY-A and CPSY-B

CPSY-A is used for synchronisation of clock 0 (TSS3 0) and CPSY-B

is used for synchronisation of clock 1 (TSS3 1). CPSY-A and CPSY-

B have two BNC connectors and three RJ-45 connectors for external

synchronisation inputs and outputs, and they are equipped in the

same network element. CPSY-A has a RJ-45 connector for service

terminal for NEMU use.

. CPAL-A

CPAL-A is a connector panel used for alarms. It has a horizontal

layout and one D25 connector for EXAU/-A control, one D37

connector for general current or voltage outputs, two D37connectors for voltage-controlled inputs, and one D25 connector for

current-controlled alarm inputs.

Figure 4. Interfaces from the back interface units of the equipment cabinet:

CPSY-A (clock TSS3 0), CPSY-B (clock TSS3 1) and CPAL-A

IN

64kIN

2MOUT2M

OUT 2M IN 2M

SYM ASYMEXT2

IN

64kIN

2MOUT2M

OUT 2M IN 2M

SYM ASYMEXT1

CPSY-A

CPSY-B

CPAL-A

TOEXAU

ETH

ALARM OUTPUTS

CURRENT

CONTROLLEDALARM INPUT

VOLTAGE CONTROLLED ALARM INPUTS

1

2

DN05160581




19/90

. CPSAL-B (in RNC only)

A connector panel type for external synchronisation and HW alarm

interfaces.

. CPRLC-B (in RNC only)

A connector panel for STM-1/OC-3 interfaces with 16 pieces of LC

connectors.

. BIE1T

A back interface unit for E1/T1 balanced interfaces with 16 pieces of

RJ-45 connectors.

. BIE1T-A (in MGW only)

A back interface unit for E1 balanced interfaces with 8 pieces of RJ-

45 connectors, two E1 interfaces via each RJ-45 connector.

. BIE1C

A back interface unit for E1 unbalanced interfaces with 32 pieces of

SMB connectors.





20/90

Figure 5. Interfaces from the back interface units of the equipment cabinet:

CPRLC-B, BIE1C, BIE1T, and BIE1T-A

1.4 Interfaces from the cabling cabinet panels

In configurations that include a cabling cabinet, the connector panels for

the PDH/TDM interfaces are located on the panels of the cabling cabinet.

The numbers of the PDH/TDM lines and the plug-in unit connectors they

connect to are listed in Cable Lists for MGW and Cable Lists for RNC.

The cabling cabinet can be used for routing cables from the network

element to the environment. Cables to the environment are routed through

from the front of the cabling cabinet.

BIE1T-A

0

1

2

3

4

5

6

7

8

9

10

11

1213

14

15

CPRLC-B BIE1C BIE1T

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

0

1

2

3

4

5

6

78

9

10

11

12

13

14

15

-

-

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

DN70461848




21/90

The cabling cabinet can be equipped with several panel types:

. CPBP

A blank panel for empty panel positions.

. CPLC36

A connector panel for STM-1/OC-3 and 1000 BASE-LX interfaces

with 36 pieces of LC connectors.

. CPSY

A connector panel for synchronisation with four BNC connectors and

six RJ-45 connectors for external synchronisation inputs andoutputs.

. CPAL

A connector panel for alarms with a vertical layout and one D25

connector for EXAU/-A control, one D37 connector for generalcurrent/voltage outputs, two D37 connectors for voltage-controlled

inputs, and one D25 connector for current-controlled alarm inputs.

. CPLAN-A

A connector panel for Local Area Network interfaces (10/100 BASE-

T/TX and 1000 BASE-T), 32 pieces of RJ-45 connectors.

. CPETS-G (in MGW only)

A connector panel with 24 pieces of RJ-45 connectors. The panel

supports forty-eight E1 interfaces, two interfaces via each RJ-45

connector.

. CPETS-E

A connector panel for 48 pieces of E1/T1 balanced (symmetrical)interfaces (twelve connector modules, each with four RJ-45

connectors).

. CPETS

A connector panel for 32 pieces of E1/T1 balanced interfaces with

32 pieces of RJ-45 connectors.

. CPETC-E

A connector panel for 48 pieces of E1 unbalanced interfaces, that is,

twelve multicoaxial D-sub connectors, each with eight coaxial

contacts.

. CPETC-B





22/90


23/90

1.5 Network Management Unit (NEMU) and service

terminal interfaces

. VDU (SVGA/VGA) interface

VDU monitor connected to the front panel of the MCPC18/-B or

MCPC2/-A plug-in unit; Windows 2000 compatible VGA connector

interface.

. USB interface

The Windows 2000 compatible USB interface accepts the printer,

mouse, or keyboard.

. Keyboard and mouse

Keyboard connected to the front panel of the NEMU plug-in unit

MCPC2/-A; Windows 2000 compatible keyboard connector. Mouse

connected to the front panel of the NEMU plug-in unit MCPC2/-A;

Windows 2000 compatible (serial) mouse connector.

. SCSI interface

External SCSI device (for instance, HD or MOD) connected to the

front panel of NEMU MCPC2/-A; external VDHCI connector

interface.

Figure 7. Network interfaces on the NEMU plug-in units MCPC2/-A and

MCP18/-B

DN05160418

NEMUMCPC2/-A

LAN

VDU

USB

MOUSE/KEYBOARD

SCSI

(EXTERNAL)

NEMUMCP18/-B

SVGA

USB

RESETSWITCH





24/90




25/90

2 Network interfaces

2.1 PDH/TDM connector panels for E1 interfaces

There are five types of connector panels for the cabling cabinet:

. CPETS-G for E1 balanced PDH interfaces, ETSI

. CPETS-E for E1/T1 balanced PDH lines, ANSI

. CPETS for E1/T1 balanced PDH lines

. CPETC-E for E1 unbalanced PDH lines

.

CPETC-B for E1 unbalanced PDH lines

There are three types of back interface units for connecting PDH lines:

. BIE1T-A for E1 balanced PDH interfaces, ETSI

. BIE1T for E1/T1 balanced PDH interfaces, ANSI

. BIE1C for E1 unbalanced PDH interfaces, ETSI

The back interface units BIE1T-A, BIE1T and BIE1C are located at the rear

of the equipment cabinet, directly behind the NIWU or NIP1 units that they

serve.

For information on cabling, see section Requirement specification for

external cables.



Network interfaces


26/90

Figure 8. Back interface unit and connector panel equipping options

DN70462765

Equipping option with only the connector panel for cabling cabinet

Equipping option withonly the back interface unit

Equipping option with both connector panel and back interface unit




27/90

2.1.1 CPETS-G, CPETS-E and CPETS

CPETS-G is a connector panel for the cabling cabinet, for 48 E1 balanced

interfaces. It consists of 4 connector bodies, each with six RJ-45

connectors, each of which supports two E1 interfaces. The internal cable

type connecting the NIWU or NIP1 to CPETS-G is CPSM. The external

cable for CPETS-G is CNIB.

Figure 9. Connector panel CPETS-G for the cabling cabinet

CPETS-E is a connector panel for the cabling cabinet, for 48 pieces of E1/

T1 balanced interfaces. The panel fitted to the panel plate consists of

twelve connector bodies, each with four RJ-45 connectors. The internal

cable type connecting the NIWU or NIP1 to CPETS-E is CPSM. The

external cable for CPETS-E is CNIA or CNIS.

DN70453111

CPETS-G

00

01

0809

16

17

24

25

32

33

40

41

02

03

1011

18

19

26

27

34

35

42

43

04

05

1213

20

21

28

29

36

37

44

45

06

07

14

15

22

23

30

31

38

39

46

47



Network interfaces


28/90

Figure 10. Connector panel CPETS-E for the cabling cabinet

CPETS is a connector panel for the cabling cabinet, for E1/T1 balanced

PDH interfaces. It consists of 32 pieces of RJ-45 connectors. The internal

cable type between BIE1T and CPETS is CPT. The external cable for

CPETS is CNIA or CNIS.

00

DN05160351

01 02 03 04 05 06 07 08 09 10 11

12 13 14 15 16 17 18 19 20 21 22 23

24 25 26 27 28 29 30 31 32 33 34 35

36 37 38 39 40 41 42 43 44 45 46 47

CPETS-E




29/90

Figure 11. Connector panel CPETS for the cabling cabinet

2.1.2 CPETC-E and CPETC-B

CPETC-E is a connector panel for the cabling cabinet for 48 pieces of E1

unbalanced interfaces, providing isolation voltage of 500V. The panel fitted

to the panel plate consists of twelve D-sub connector bodies, each with

eight coaxial contacts. The internal cable type connecting NIWU or NIP1

unit to CPETC-E is CPSM. The external cable for CPETC-E is CPRD.

DN98618022

00

08

16

24

01

09

17

25

02

10

18

26

03

11

19

27

04

12

20

28

05

13

21

29

06

14

22

30

07

15

23

31



Network interfaces


30/90

Figure 12. Connector panel CPETC-E for the cabling cabinet

CPETC-B is a connector panel for the cabling cabinet, for E1 unbalanced

PDH interfaces. It consists of 64 pieces of BT43 coaxial connectors. The

internal cable type between BIE1C and CPETC-B (SMB/BT43) is CBTC

(internal cabling).

00

02

04

06

08

10

01

03

05

07

09

11

DN05160363 CPETC-E

RxTx RxTx RxTx RxTx

00

78 56 34 12

01 02 03




31/90

Figure 13. Connector panel CPETC-B for the cabling cabinet

2.1.3 BIE1T-A, BIE1T and BIE1C

BIE1T-A is a back interface unit for E1 balanced interfaces with eight RJ-

45 connectors, two E1 interfaces via each RJ-45 connector.

BIE1T is a back interface unit for E1/T1 balanced interfaces that consists

of 16 pieces of RJ-45 connectors for 16 physical PDH lines.

BIE1C is a back interface unit for E1 unbalanced interfaces, with 32 pieces

of SMB connectors for 16 physical PDH lines.

2.1.4 E1T48-A and E1C48-A

E1T48-A or E1C48-A are connector panels for PDH interfaces at the rear

of the IC186 equipment cabinet. Connector panel E1T48-A contains 48

pieces of RJ-45 connectors for 48 physical E1/T1 balanced interfaces to

the environment. Connector panel E1C48-A consists of 96 pieces of BT43

coaxial connectors for 48 physical E1 unbalanced interfaces to the

environment.

Tx

Rx

Tx

Rx

Tx

Rx

Tx

Rx

00

08

16

24

01

09

17

25

02

10

18

26

03

11

19

27

04

12

20

28

05

13

21

29

06

14

22

30

07

15

23

31

DN0445768



Network interfaces


32/90

Figure 14. E1T48-A (upper) and E1C48-A (lower) connector panels for the

IC186 equipment cabinet

Both E1T48-A and E1C48-A panels can be equipped and in the same

equipment cabinet at the same time, as long as each panel supports three

network interface plug-in units that have same type of connector interfaces

(RJ-45 or BT43). This means that all of the three NIP1 or NIWU units that

the E1T48-A or E1C48-A panel serves must use the connector type thatthe selected panel type serves.

The RNAC and RNBC/CAMA and CAMB cabinets have only five panel

places for the PDH lines. The panels are numbered sequentially from top

to bottom, starting from number 1. The connectors for the outgoing PDH

lines on the panels also have numbers that run from left to right and top to

bottom.

2.2 STM-1/OC-3 interfaces

2.2.1 Front panels of the NP8S1/-A/-B, NI4S1-B, IW1S1A and IW1S1 plug-in units

The NP8S1/-A/-B (NPS1P/NPS1), NI4S1-B (NIS1P/NIS1) and IW1S1A/

IW1S1 (IWS1E/T) plug-in units have ITU-T G.957 S-1.1 STM-1/OC-3

optical interfaces on the front panel. The transmission interface uses

single-mode fibre. The connector type is fibre optic LC duplex. The STM-1/

DN0136686

Tx

Tx

Rx

Rx




33/90

OC-3 interfaces are connected either directly from the front panel of the

plug-in units or via connector panel CPLC36 in the cabling cabinet. In theRNC, it is also possible to route the connections via the CPRLC-B panel at

the rear of the RNAC.

Figure 15. Front panel of the NP8S1 plug-in unit

DN70182603 NP8S1

1

2

3

4

5

6

7

8

STM-1 / STM-4

Tx

Rx

Tx

Rx

Tx

Rx

Tx

Rx

Tx

Rx

Tx

Rx

Tx

Rx

Tx

Rx

STM-1

SERVICE TERMINAL

INTERFACES:

BACKPLANE:

- TIMING & SYNC

- HMS

- POWER SUPPLY

- SFU- CLOCK REFERENCE

OUTPUT TO TSS3- LAN 1-5

CLASS 1 LASER PRODUCTIEC/EN 60825-1



Network interfaces


34/90

Figure 16. Front panel of the NI4S1-B plug-in unit

NI4S1-B DN02179368

INTERFACES:

BACKPLANE:

- TIMING & SYNC- HMS- POWER SUPPLY- SFU

- CLOCKREFERENCEOUTPUT TO TSS3

LAN (NOT USED)

STM-1

SERVICE TERMINAL




35/90

Figure 17. Front panel of the IW1S1/A plug-in unit

2.2.2 Connector panel CPLC36

CPLC36 is a connector panel in the cabling cabinet for optical interfaces,

such as STM-1/OC-3. It has 36 pieces of duplex LC connectors. The

external and internal cable type used is CLCS or CSMA.

DN0490465

LAN (NOT USED)

SERVICE TERMINAL

BACK PLANE:

- TIMING & SYNC- HMS

- POWER SUPPLY- MXU

INTERFACES:

STM-1

STM-1 REDUNDANT



Network interfaces


36/90

Figure 18. Connector panel CPLC36 in the cabling cabinet

2.2.3 Connector panel CPRLC-B

CPRLC-B is a connector panel in the RNC for STM-1/OC-3 interfaces. It

has 16 pieces of LC connectors. CPRLC-B is equipped in the SRBI at the

rear of the cabinet, as shown in the figure below.

06 07 08 09 10 11

12 13 14 15 16 17

18 19 20 21 22 23

24 25 26 27 28 29

30 31 32 33 34 35

00 01 02 03 0504

CLASS

1LASER

PRODUCT

EN

60825-11994

DN0445732

Opticalproduct

LC connector




37/90

Figure 19. Equipping the connector panel CPRLC-B

2.3 LAN/Ethernet interfaces

The local area network (LAN) interface using RJ-45 connectors is located

on the front panels of the plug-in units of the MGW or RNC and the

connector panel of the cabling cabinet.

. Two optical LAN 1000 BASE-LX and two electrical LAN 1000 BASE-

T interfaces from NP2GE (NPGEP/NPGE)

. One optical LAN 1000 BASE-LX (IPGOP), one electrical LAN 1000

BASE-T (IPGEP), and eight electrical LAN 100 BASE-T (IPFEP)

interfaces from IPFGE (IPNIUP, in MGW only)

. Twenty-four interfaces provided by the ESA24 plug-in unit

. Twelve interfaces provided by the ESA12 plug-in unit

SRBI-B

-

-

8 0

9 1

10 2

11 3

12 4

13 5

14 6

15 7

CPRLC-B

DN03463441

08

715



Network interfaces


38/90

2.3.1 Front panel of the NP2GE/-A plug-in unit

The NP2GE/-A plug-in unit is a network interface unit providing two optical

or electrical gigabit Ethernet interfaces. The connector type for

1000BASE-LX is LC, whereas 1000BASE-T uses the RJ-45 connector.

The optical 1000BASE-LX interfaces are connected either directly from the

front panel of the plug-in units or via connector panel CPLC36 in the

cabling cabinet. The electrical 1000BASE-T interfaces are connected

either directly from the front panel of the plug-in units or via connector

panel CPLAN-A in the cabling cabinet.

Specifications for optical 1000-Base-LX interface:

. Optical output power: min -9dBm, max -3dBm

. Minimum input optical power: min -20dBm

. Maximum input optical power: min -3dBm




39/90

Figure 20. Front panel of the NP2GE plug-in unit

Table 1. Interfaces at the NP2GE/-A plug-in unit

FU Front panel connector Use

NPGE / NPGEP F (1000_BASE-T) 1000 BASE-T

NPGE / NPGEP F (1000_BASE-LX) 1000 BASE-LX

DN70182857 NP2GE

0

1

SERVICETERMINAL

CLASS 1 LASER PRODUCTIEC/EN 60825-1

1000BASE-T

1000BASE-LX

1000BASE-T

1000BASE-LX0

1

Tx

Rx

Tx

Rx



Network interfaces


40/90

2.3.2 Front panel of the IPFGE plug-in unit

The IPFGE plug-in unit is a network interface unit providing eight electrical

Fast Ethernet (100 Mbps) interfaces, one optical and one electrical gigabit

Ethernet. Only one of the gigabit interfaces can be used at a time (8 x fast

Ethernet, 1 x gigabit optical, or 1 x gigabit electrical). The connector type

for 1000BASE-LX is LC, whereas 1000BASE-T uses the RJ-45 connector.

Specifications for optical 1000-Base-LX interface:

. Optical output power: min -9dBm, max -3dBm

. Minimum input optical power: min -20dBm

. Maximum input optical power: min -3dBm




41/90

Figure 21. Front panel of the IPFGE plug-in unit

Table 2. Interfaces at the IPFGE plug-in unit

FU Front panel connector Use

IPGO / IPGOP 0 F (1000_BASE-LX) 1000 BASE-LX

IPGE / IPGEP 0 F (1000_BASE-T) 1000 BASE-T

IPFE / IPFEP 0 F 0-7 10/100 BASE-T/TX

IPFGE

LAN(Not used)

100BASE-TX

1000BASE-T

LED

1000BASE-LX/LH

DN02180131

SERVICETERMINAL



Network interfaces


42/90

2.3.3 Front panels of the ESA24 and ESA12 plug-in units

An equipment cabinet is configured with either the ESA24 or ESA12 plug-

in unit.

Figure 22. Front panel of the ESA24 plug-in unit

Table 3. Interfaces at the ESA24/ESA12 units

FU Connectors and their use

ESA24

(NEMU)

There are two front panel connectors for external use (out of the NE).

The other 22 LAN interfaces are in the backplane connectors, and they are

for the internal use of the NE.

ESA24 DN03451956

INTERFACES:

LAN

BACKPLANE:

- HMS (NOT USED)- POWER SUPPLY

- LAN

SERVICE TERMINAL

- TIMING & SYNC(NOT USED)




43/90


44/90


45/90

3 Maintenance interfaces

3.1 NEMU-specific maintenance interfaces

Table 4. Interfaces on the NEMU units

Plug-in unit/interface (connector) Use

MCP18/-B MCPC2/-A

ETH0

(back panel connector)

ETH0

(RJ-45)

For LAN use

ex to eth SW

ETH1


ETH1

(RJ-45)

for LAN use

ex to eth SW

4 X USB - for bootable device

for mouse, keyboard

for printer

- 1 x USB for printer

- 1 x PS/2 for keyboard and mouse

SVGA SVGA for VDU

- SCSI

(D68)

for bootable device

- RS1


serial port 1

- RS2


serial port 2



Maintenance interfaces


46/90

3.1.1 VDU (VGA) interface pinout

VDU monitor connected to the front panel of the MCPC2/-A; Windows NT-

compatible VGA connector interface.

Table 5. SVGA interface pinout (D15)

Pin Signal Pin Signal

1 Red 9 NC

2 Green 10 GND

3 Blue 11 NC

4 NC 12 DDCDAT

5 GDN 13 H-sync

6 DACGND 14 V-sync

7 DACGND 15 DDCCLK

8 DACGND

3.1.2 USB interface pinout

The Windows NT-compatible USB interface accepts a printer, mouse or

keyboard.

Table 6. USB interface pinout (4 pins)

Pin Signal

Mechanical solder lug Shield ground

1 +5 V

2 Data -

3 Data +

4 GND

Mechanical solder lug Shield ground




47/90

3.1.3 Keyboard and mouse pinout

Keyboard connected to the front panel of (NEMU) MCPC2/-A; Windows

NT-compatible keyboard connector. Mouse connected to the front panel of

(NEMU) MCPC2/-A; Windows NT compatible (serial) mouse connector.

Table 7. Keyboard and mouse pinout (6 pins)

Pin Signal

1 Mouse data

2 Keyboard data

3 GND

4 +5 V

5 Mouse clock

6 Keyboard clock

3.1.4 SCSI interface pinout

External SCSI device (example HD or MOD) connected to the front panelof (NEMU) MCPC2/-A; external VHDCI connector interface.

Table 8. SCSI interface pinout (D68)

Pin Signal Pin Signal Pin Signal

1 +DB (12) 24 +ACK 47 -DB(7)

2 +DB (13) 25 +RST 48 -DB(P)

3 +DB (14) 26 +MSG 49 GND

4 +DB (15) 27 +SEL 50 GND

5 +DB (P1) 28 +C/D 51 TERMPWR

6 +DB(0) 29 +REQ 52 TERMPWR

7 +DB(1) 30 +I/O 53 RESERVED

8 +DB(2) 31 +DB(8) 54 GND

9 +DB(3) 32 +DB(9) 55 -ATM

10 +DB(4) 33 +DB(10) 56 GND

11 +DB(5) 34 +DB(11) 57 -BSY

12 +DB(6) 35 -DB(12) 58 -ACK





48/90

Table 8. SCSI interface pinout (D68) (cont.)


13 +DB(7) 36 -DB(13) 59 -RST

14 +DB(P) 37 -DB(14) 60 -MSG

15 GND 38 -DB(15) 61 -SEL

16 DIFFSENS 39 -DB(P1) 62 -C/D

17 TERMPWR 40 -DB(0) 63 -REQ

18 TERMPWR 41 -DB(1) 64 -I/O

19 RESERVED 42 -DB(2) 65 -DB(8)

20 GND 43 -DB(3) 66 -DB(9)

21 +ATN 44 -DB(4) 67 -DB(10)

22 GND 45 -DB(5) 68 -DB(11)

23 +BSY 46 -DB(6)

3.1.5 LAN interface pinout

Table 9. LAN/Ethernet interface pinouts (RJ-45) for CPU, AL2S, CDSP and

ESA24/ESA12 plug-in units

Pin Signal

1 Transmit + (Tx+)

2 Transmit - (Tx-)

3 Receive + (Rx+)

4

5

6 Receive - (Rx-)

7

8




49/90

3.2 Service terminal interface

The RS232 interface using the RJ-45 connector is located on the front

panel of certain units. The interface is used for logging into and for

accessing the service terminal.

. One interface provided by NP2GE/-A, NI16P1A, NP8S1/-A, CDSP,

NI4S1-B, IW16P1, IW16P1A, IW1S1, IW1S1A, AL2S and SF20H

plug-in units

. Two interfaces provided by CPU plug-in units, SF10, MX1G6/-A,

MX622, and MCPC2/-A

Table 10. Service terminal interface pinout (RJ-45)

Pin Signal

1 DTR Data terminal ready

2 TxD Transmit data

3 GND

4 GND

5 RxD Receive data

6 DSR Data set ready

7 CTS Clear to send

8 RTS Request to send





50/90




51/90

4 Connector panels for external alarm andsynchronisation interfaces

Depending on the equipment installed, the external alarm andsynchronisation interfaces are provided by different types of connector

panels:

. CPAL-A and CPAL are for external alarm signals and for the external

alarm unit, EXAU/-A

. CPSY-A, CPSY-B and CPSY are for synchronisation

. CPSAL/-B is for both alarms and synchronisation

CPAL-A, CPSY-A, CPSY-B and CPSAL/-B are back panels of the

equipment cabinet.

CPAL and CPSY are equipped in the cabling cabinet.

4.1 CPAL/-A and CPSAL/-B for alarm interfaces

Connector panels CPAL/-A and CPSAL/-B for alarms have one D25

connector for EXAU/-A control, one D37 connector for general current orvoltage outputs, two D37 connectors for voltage-controlled inputs, and one

D25 connector for current-controlled alarm inputs.



Connector panels for external alarm and synchronisation interfaces


52/90

Figure 24. Connector panels CPAL/-A and CPSAL/-B for alarm interfaces

Table 11. Voltage-controlled alarm inputs 1 (D37)


1 VAL0 14 GND 27 VAL13

2 GND 15 VAL7 28 GND




CPAL ALARMOUTPUTTO EXAU

ALARMOUTPUT

VOLTAGECONTROLLED

ALARM INPUTS

CURRENTCONTROLLEDALARM INPUT

1 2

DN05160636

1 2 1 2

1 23 4 3 4

SYM SYM

ASYM ASYMSYM

IN 2M OUT 2MIN 64k

ALARMOUTPUT

TO EXAU

ALARMOUTPUT

VOLTAGECONTROLLED

ALARM INPUTS

CURRENTCONTROLLED

ALARM INPUT21

CPSAL/-B

CPAL-A

TOEXAU

ALARMOUTPUTS


VOLTAGE CONTROLLEDALARM INPUTS

1

2




53/90

Table 11. Voltage-controlled alarm inputs 1 (D37) (cont.)



7 VAL3 20 GND 33

8 GND 21 VAL10 34

9 VAL4 22 GND 35

10 GND 23 VAL11 36

11 VAL5 24 GND 37

12 GND 25 VAL12

13 VAL6 26 GND

Table 12. Voltage-controlled alarm inputs 2 (D37)


1 VAL16 14 GND 27 VAL29


3 VAL17 16 GND 29 VAL30


5 VAL18 18 GND 31 VAL31


7 VAL19 20 GND 33

8 GND 21 VAL26 34

9 VAL20 22 GND 35

10 GND 23 VAL27 36

11 VAL21 24 GND 37

12 GND 25 VAL28

13 VAL22 26 GND

Table 13. Current-controlled alarm inputs (D25)


1 CAL0 14 GND





54/90

Table 13. Current-controlled alarm inputs (D25) (cont.)


2 GND 15 CAL7

3 CAL1 16 GND

4 GND 17

5 CAL2 18

6 GND 19

7 CAL3 20

8 GND 21

9 CAL4 22

10 GND 23

11 CAL5 24

12 GND 25

13 CAL6 26

Table 14. Alarm outputs to the External Alarm Unit (EXAU/-A) (D25)


1 AL0 14 GND

2 GND 15 AL7

3 AL1 16 GND

4 GND 17 AL8

5 AL2 18 GND

6 GND 19 AL9

7 AL3 20 GND

8 GND 21 AL10

9 AL4 22 GND

10 GND 23 AL11

11 AL5 24 GND

12 GND 25

13 AL6 26




55/90

Table 15. Alarm outputs (D37)


1 ALO0 14 GND 27 ALO13

2 GND 15 ALO7 28 GND





7 ALO3 20 GND 33

8 GND 21 ALO10 34

9 ALO4 22 GND 35

10 GND 23 ALO11 36

11 ALO5 24 GND 37

12 GND 25 ALO12

13 ALO6 26 GND

4.2 CPSY-A, CPSY-B, CPSY and CPSAL/-B forsynchronisation interfaces

Connector panels CPSY-A, CPSY-B, CPSY and CPSAL/-B consist of BNC

connectors and RJ-45 connectors for external synchronisation inputs and

outputs.





56/90

Figure 25. Connector panels CPSY-A, CPSY-B, CPSY and CPSAL/-B for alarm

and synchronisation interfaces

DN05160648

CPSY-B

IN

64kIN

2MOUT2M

OUT 2M IN 2M

SYM ASYMEXT2

Default

CPSY

1 2 1 2

SYM SYM

3 4 1 2 3 4

SYM ASYMASYM

2M 64k 2MIN IN OUT

Default

1 2 1 2

1 23 4

3 4

SYM SYM

ASYM ASYMSYM

IN 2M OUT 2MIN 64k

ALARMOUTPUTTO EXAU

ALARMOUTPUT

VOLTAGECONTROLLED

ALARM INPUTS


21

CPSAL/-B

Default

CPSY-A

IN

64kIN

2MOUT2M

OUT2M IN 2M

SYM ASYMEXT1

ETH

Default




57/90


58/90

OUT 2M synchronisation interface

. Coaxial BNC connectors (unbalanced)

Two BNC connectors OUT 2M provide two unbalanced (ASYM)

output interfaces.

. RJ-45 connectors (balanced)

Two RJ-45 connectors provide two balanced output interfaces for

2M signals OUT 2M.

Table 18. Synchronisation (OUT 2M) interface pinout (RJ-45)

Pin Signal

13 No signal

4 2M OUT A / Transmit + (Tx+)

5 2M OUT B / Transmit - (Tx-)

68 No signal




59/90

5 Requirement specification for externalcables

5.1 E1 and T1 balanced (symmetrical) PCM

If the cabling cabinet is not used, E1 balanced (symmetrical) PCM cables

are connected to the BIE1T-A, BIE1T or E1T48-A interface panel, and if

the cabling cabinet is used, the cables are connected to the CPETS-G,

CPETS-E or CPETS interface panel.

Cable specifications

.

Connector:. RJ-45 connector

. Shielded construction

. Gold plating on the contacts (0.76 m)

. UL94 V-0 materials

. Cable:

. Multi-cable (4 or more) bundled assembly

. Nominal impedance: 120 15 for E1 and 100 15 for T1

. E1 data transmission protocol specifies 6 dB as maximum

attenuation

. AWG 26 or AWG 24 conductors

. Continuous pair twisting

. VW-1 materials

. Flammability: IEC 332-1 or IEC 332-3

. Operating temperature from 0 C to 70 C



Requirement specification for external cables


60/90

Table 19. Cable CNIA E1 (120 ) component codes

Item Code

Connector 5461630

Plastic part 7333689

Cable (multi-cable) 7131850

Table 20. Cable CNIS T1 (100 ) component codes

Item Code

Connector 5461630


Cable (single-cable) 7131860

Table 21. Cable CNIB (120) component codes

Item Code

Connector 5461630


Cable (multi-cable) 7131851

Table 22. RJ-45 connector pinouts (CNIA/CNIS)

Position Signal, generic names Wire pair #

1 Receive - (Rx-) 2

2 Receive + (Rx+) 2

3 n.c.

4 Transmit - (Tx-) 1

5 Transmit + (Tx+) 1

6 n.c.

7 n.c.

8 n.c.




61/90

Table 22. RJ-45 connector pinouts (CNIA/CNIS) (cont.)


n.c. = not connected

Table 23. RJ-45 connector pinouts (CNIB)


1 Receive - (Rx-) 2

2 Receive + (Rx+) 2

3 Receive - (Rx-) 3



6 Receive + (Rx+) 3



Figure 26. Example of CNIA cable assembly

CONNECTOR

DN00206525

1 2 3 4





62/90

Figure 27. Connecting a PCM E1 cable to a connector, CNIS (example)

5.2 E1 unbalanced (coaxial) cables

There are three different connector types of unbalanced (coaxial) cables

depending on the interface panel. SMB connectors are used with BIE1C

interface panel and BT43 connectors are used with the CPETC-B and

E1C48-A panels. Multicoaxial D-sub connectors are used with CPETC-E.

The BIE1C panel is equipped in the equipment cabinet, whereas the

CPETC-B and CPETC-E panels are equipped in the cabling cabinet. The

E1C48-A panel is equipped in the equipment cabinet.

5.2.1 E1 unbalanced (coaxial) cables with the CPETC-E panel

There are twelve D37 multicoaxial connector bodies on the CPETC-E

interface panel. Each D37 connector body has eight unbalanced (coaxial)

connector contacts. Balanced (120) to unbalanced (75) transformation

is carried out on the CPETC-E panel.

8

MODULAR CONNECTOR

SLEEVE

CABLE

IDENTIFICATIONSTICKER

DN98339941




63/90


. Connector:

. Connector D37 body with unbalanced (coaxial) contacts

. Gold plating on the contacts (minimum for centre contact 1.27

m, minimum for outer contact 0.76 m)


. Cable:

. Impedance 75 3

. Multicoaxial cable

. E1 data transmission protocol specifies 6dB as maximum

attenuation. VW-1 material



Table 24. Component codes for the unbalanced (coaxial) CPRD cable

Item Code

Connector body 5436732

Connector contact 5463552

Jack screw 5461696

Case 5461984

Multicoaxial cable 7134984

Figure 28. D37 connector body with unbalanced (coaxial) contacts (1=pin,

2=ring)

A7A8 A5A6 A3A4 A1A2

DN05160651

1

2





64/90

Table 25. D37 connector pinouts

Pin Function

A8-1 TxTip_0

A8-2 TxRing_0

A7-1 RxTip_0

A7-2 RxRing_0

A6-1 TxTip_1

A6-2 TxRing_1

A5-1 RxTip_1

A5-2 RxRing_1

A4-1 TxTip_2

A4-2 TxRing_2

A3-1 RxTip_2

A3-2 RxRing_2

A2-1 TxTip_3

A2-2 TxRing_3

A1-1 RxTip_3

A1-2 RxRing_3

5.2.2 E1 unbalanced (coaxial) cables with the BIE1C panels

If the cabling cabinet is not used, E1 unbalanced (coaxial) cables are

connected to the BIE1C interface panel. The BIE1C interface panels have

SMB connectors and are located at the rear of the cabinet behind the

NI16P1A and/or IW16P1 plug-in units.


. Connector:

. SMB connector, 50




. Cable:

. Impedance 75 3

. Single or multicoaxial cable




65/90





Table 26. Component codes for unbalanced (coaxial) cable

Item Code

Connector 5426008

Connector sleeve 5421434

Cable 7134962


Figure 29. Example of E1 multicoaxial cable with SMB connectors

5.2.3 E1 unbalanced (coaxial) cables with the E1C48-A or CPETC-B panel

The E1C48-A interface panels are located at the rear of the cabinet. If the

cabling cabinet is used, E1 unbalanced (coaxial) cables are connected to

the CPETC-B interface panel. The CPETC-B interface panels have BT43

connectors, and are located in the cabling cabinet.

CONNECTOR 1 2 3 4 5 6 7 8

DN0557322





66/90


. Connector:

. BT43 connector, 75



. Recommended: UL94 V-0 materials

. Cable:

. Impedance 75 3

. Single or multicoaxial cable





Table 27. Component codes for unbalanced (coaxial) cable

Item Code

Connector 5425506

Connector sleeve 5421434

Cable 7134962





67/90

Figure 30. Example of E1 multicoaxial cable with BT43 connectors

5.3 Alarm output to EXAU/-A

If the cabling cabinet is not used, the alarm output cable to the EXAU/-A is

connected to the CPAL-A or CPSAL/-B panel, whereas if the cabling

cabinet is used, the cable is connected to the CPAL panel.


. Connector:

. 25 pos. D-sub male connector



.

UL94 V-0 materials

. Connector hood:

. Connector hood must be shielded

. Side entry for cable

. UNC 4/40 thumb screws

. Maximum height of hood 50 mm

. Cable:


. Minimum 12 twisted pairs

CONNECTOR 1 2 3 4 5 6 7 8

DN0557334





68/90

. Shielded construction, screening effectiveness > 35dB at

1GHz. VW-1 materials



Table 28. Cable CNDC (version A01) component codes

Item Code Note

Connector 5433649

Connector shell 5438878

Cable bushing 5438884

Cable 8 x 2 7131862 1)

1) Due to the 8 x 2 cable, only AL07 AL7 alarm signals are connected.

Table 29. Cable CNDC (version A02) component codes

Item Code Note

Connector 5433649



Cable 12 x 2 7131864 1)

1) Due to the 12 x 2 cable, alarm signal AL0 AL11 are connected.

Version A02 cable is needed when alarm signals AL6 AL11 need to be

chained. Only EXAU-A has the chaining feature.

The EXAU-A unit has an alarm output connector, allowing it to chain two or

more EXAU-A units so that alarms coming from the network element canbe displayed on two or more EXAU-A units.

The tables below describe the connector pinouts for the following cases:




69/90

. Displaying alarms on EXAU-A or EXAU: connecting the alarm cable

from CPSAL/-B to EXAU/-A. Displaying the same alarms on two EXAU-A units: chaining EXAU-A

1 to EXAU-A 2 with a direct cable

. Displaying alarms AL00 to AL05 on EXAU 1 and alarms AL06 to

AL11 on EXAU-A 2: chaining EXAU-A 1 to EXAU-A 2 with a

crossover cable

For more information on EXAU-A and the chaining principles, see the

EXAU-A plug-in unit description in MGW product documentation.

Table 30. Connector pinouts for a cable from CPSAL/-B to EXAU/-A or EXAU-

A 1 to EXAU-A 2 with a direct cable

Position -

CPSAL or

EXAU-A 1

Signal Position -

EXAU/-A or

EXAU-A 2

Wire pair #

1 AL0 1 1

2 GND 2 1

3 AL1 3 2

4 GND 4 2

5 AL2 5 3

6 GND 6 3

7 AL3 7 4

8 GND 8 4

9 AL4 9 5

10 GND 10 5

11 AL5 11 6

12 GND 12 6

13 AL6 13 7

14 GND 14 7

15 AL7 15 8

16 GND 16 8

17 AL8 17 9

18 GND 18 9

19 AL9 19 10

20 GND 20 10

21 AL10 21 11





70/90

Table 30. Connector pinouts for a cable from CPSAL/-B to EXAU/-A or EXAU-

A 1 to EXAU-A 2 with a direct cable (cont.)

Position -

CPSAL or

EXAU-A 1

Signal Position -

EXAU/-A or

EXAU-A 2

Wire pair #

22 GND 22 11

23 AL11 23 12

24 GND 24 12

25 25

Table 31. Connector pinouts for a cable from EXAU-A 1 to EXAU-A 2 with a

crossover cable

Position -

EXAU-A 1

Signal Position -

EXAU-A 2

Wire pair #

1 AL0 13 1

2 GND 14 1

3 AL1 15 2

4 GND 16 2

5 AL2 17 3

6 GND 18 3

7 AL3 19 4

8 GND 20 4

9 AL4 21 5

10 GND 22 5

11 AL5 23 6

12 GND 24 6

13 AL6 1 7

14 GND 2 7

15 AL7 3 8

16 GND 4 8

17 AL8 5 9

18 GND 6 9

19 AL9 7 10

20 GND 8 10




71/90

Table 31. Connector pinouts for a cable from EXAU-A 1 to EXAU-A 2 with a

crossover cable (cont.)

Position -

EXAU-A 1

Signal Position -

EXAU-A 2

Wire pair #

21 AL10 9 11

22 GND 10 11

23 AL11 11 12

24 GND 12 12

25 25

Figure 31. Example of alarm cable to the EXAU/-A

5.4 Alarm input cable

If the cabling cabinet is not used, the alarm output cable is connected to

the CPAL-A or CPSAL/-B panel, and if the cabling cabinet is used, thecable is connected to the CPAL panel.


. Connector:





DN0557346





72/90

. Connector hood:

.

Shielded construction. Side entry for cable


. Maximum height of hood 55 mm (cable exits from side of

hood)

. Cable:




1GHz

. VW-1 materials



Table 32. Component codes for alarm output cable

Item Code

Connector 5437752


Strain relief 5434144

Cable 20 x 2 7131866

Table 33. Connection pinouts for voltage-controlled alarm input

Position Signal Wire pair #

1 ALO0 1

2 GND 1

3 ALO1 2

4 GND 2

5 ALO2 3

6 GND 3

7 ALO3 4

8 GND 4

9 ALO4 5

10 GND 5




73/90

Table 33. Connection pinouts for voltage-controlled alarm input (cont.)


11 ALO5 6

12 GND 6

13 ALO6 7

14 GND 7

15 ALO7 8

16 GND 8

17 ALO8 9

18 GND 9

19 ALO9 10

20 GND 10

21 ALO10 11

22 GND 11

23 ALO11 12

24 GND 12

25 ALO12 13

26 GND 13

27 ALO13 14

28 GND 14

29 ALO14 15

30 GND 15

31 ALO15 16

32 GND 16

33

34

35

36

37





74/90

Figure 32. Example of alarm output cable

5.5 Voltage-controlled alarm input

If the cabling cabinet is not used, the voltage-controlled alarm input cable

is connected to the CPAL-A or CPSAL/-B panel, and if the cabling cabinet

is used, the cable is connected to the CPAL panel. The panels have two

D37 connectors for voltage-controlled alarm inputs.


. Connector:





. Connector hood:

.

Shielded construction. Side entry for cable


. Maximum height of hood 55 mm (cable exits from side of

hood)

. Cable:




1GHz

DN0557361




75/90

. VW-1 materials

.

Flammability: IEC 332-1 or IEC 332-3. Operating temperature from 0 C to 70 C

Table 34. Component codes for voltage-controlled alarm input cable

Item Code

Connector 5437752


Strain relief 5434144

Cable 20x2 7131866

Table 35. Connection diagram for voltage-controlled alarm input


1 VAL0 / VAL16 1

2 GND 1

3 VAL1 / VAL17 2

4 GND 2

5 VAL2 / VAL18 3

6 GND 3

7 VAL3 / VAL19 4

8 GND 4

9 VAL4 / VAL20 5

10 GND 5

11 VAL5 / VAL21 6

12 GND 6

13 VAL6 / VAL22 7

14 GND 7

15 VAL7 / VAL23 8

16 GND 8

17 VAL8 / VAL24 9

18 GND 9

19 VAL9 / VAL25 10

20 GND 10





76/90

Table 35. Connection diagram for voltage-controlled alarm input (cont.)


21 VAL10 / VAL26 11

22 GND 11

23 VAL11 / VAL27 12

24 GND 12

25 VAL12 / VAL28 13

26 GND 13

27 VAL13 / VAL29 14

28 GND 14

29 VAL14 / VAL30 15

30 GND 15

31 VAL15 / VAL31 16

32 GND 16

33

34

35

36

37

Figure 33. Example of voltage-controlled alarm input cable

DN0557361




77/90

5.6 Current-controlled alarm input

If the cabling cabinet is not used, the current-controlled alarm input cable is

connected to the CPAL-A or CPSAL/-B panel, and if the cabling cabinet is

used, the cable is connected to the CPAL panel.


. Connector:





. Connector hood:


. Side entry for cable


. Maximum height of hood 50 mm

. Cable:


.

Minimum 8 twisted pairs. Shielded construction, screening effectiveness > 35dB at

1GHz

. VW-1 materials



Table 36. Component codes for cable CNDC

Item CodeConnector 5433649



Cable 8 x 2 7131862





78/90

Table 37. Connection diagram for current-controlled alarm input


1 CAL0 1

2 GND 1

3 CAL1 2

4 GND 2

5 CAL2 3

6 GND 3

7 CAL3 4

8 GND 4

9 CAL4 5

10 GND 5

11 CAL5 6

12 GND 6

13 CAL6 7

14 GND 7

15 CAL7 8

16 GND 8

17 n.c.

18 n.c.

19 n.c.

20 n.c.

21 n.c.

22 n.c.

23 n.c.

24 n.c.

25 n.c.





79/90

Figure 34. Example of current-controlled alarm input cable

5.7 Asymmetrical external synchronisation

If the cabling cabinet is not used, the asymmetrical external

synchronisation cable is connected to the CPSY-A, CPSY-B or CPSAL/-B

panel, and if the cabling cabinet is used, the cable is connected to the

CPSY panel. The panels have input connectors for 2M or 1.5M

asymmetrical synchronisation signals and output connectors for 2M or

1.5M asymmetrical synchronisation signals.


. Connector:

. Male BNC


. Gold plating on the contacts (minimum centre contact 1.27 m,

minimum outer contact 0.76 m)


. Cable:

. Unbalanced (coaxial) (for example BT 3002)

. Impedance 75 3

. VW-1 materials



DN0557346





80/90

Table 38. Component codes for asymmetrical external synchronisation cable

Item Code

Connector 5420160

Cable 7130200

Figure 35. Example of asymmetrical external synchronisation cable

5.8 Symmetrical external synchronisation

If the cabling cabinet is not used, the symmetrical external synchronisation

cable is connected to the CPSY-A, CPSY-B or CPSAL/-B panel, and if the

cabling cabinet is used, the cable is connected to the CPSY panel. The

panels have input connectors for 2M or 1.5M and 64K symmetrical

synchronisation signals and output connectors for 2M or 1.5M symmetrical

synchronisation signals.


. Connector:

. Shielded RJ-45



. Cable:

. Minimum 1 twisted pair

.

Nominal impedance: 120 15

for E1 and 100 15

for T1

DN0557373




81/90


attenuation. AWG 26 or AWG 24 solid conductors

. Continuous pair twisting

. VW-1 materials



Table 39. Cable CNIA E1 component codes (120, receive and transmit

signals connected)

Item Code

Connector 5461630


Cable 7131850

Table 40. 64K / 2M / 1.5M symmetrical synchronisation input connector

pinouts


1 64K/2M IN A / Receive + (Rx+) 1

2 64K/2M IN B / Receive - (Rx-) 1

3 n.c.

4 n.c.

5 n.c.

6 n.c.

7 n.c.

8 n.c.


Table 41. 2M / 1.5M symmetrical synchronisation output connector pinouts


1 n.c.

2 n.c.





82/90


83/90

5.9 10Base-T/100Base-TX


. Connector:

. Shielded RJ-45



. Cable:

. S-FTP (foil shield twisted pair) construction

. Category 5

. AWG 26 (or AWG 24) conductors

. Meets EN 50288-2-2 standard

. VW-1 materials


. Halogen-free materials


Table 42. Component codes for CNIX (cross-connected) or CNI (straight)

cable

Item Code

Connector 5461634

Cable 7131860

Table 43. Cross-connected cable

Pos. Signal, generic

names

EIA/TIA 568A

crossed wiring

Pos. Signal, generic

names

1 Receive + (Rx+) White/green 3 Transmit + (Tx+)

2 Receive - (Rx-) Green/white 6 Transmit - (Tx-)

3 Transmit + (Tx+) White/orange 1 Receive + (Rx+)

4 Blue/white 7

5 White/blue 8

6 Transmit - (Tx-) Orange/white 2 Receive - (Rx-)

7 White/brown 4

8 Brown/white 5





84/90

Figure 37. Example of LAN cable

5.10 1000Base-T

Gigabit Ethernet cabling is connected to the IPFGE plug-in unit or

connector panel CPLAN-A.


. Connector:

. Shielded RJ-45



. Cable:

. S-FTP construction

. Category 5e

. AWG 26 (or AWG 24) conductors

. Meets the EN 50288-2-2 standard

. VW-1 materials


8

MODULAR CONNECTOR

SLEEVE

CABLE


DN98339941




85/90

. Halogen-free materials

.

Operating temperature from 0 C to 70 C

Table 44. Connector pinouts

Pos. No. Signal Wire colour (EIA 568-B)

1 TP0+ White/orange

2 TP0- Orange

3 TP1+ White/green

4 TP2+ Blue

5 TP2- White/blue

6 TP1- Green

7 TP3+ White/brown

8 TP3- Brown

Figure 38. Example of LAN cable

8

MODULAR CONNECTOR

SLEEVE

CABLE


DN98339941





86/90

5.11 Optical STM-1

If the cabling cabinet is not used, optical STM-1 fiber is connected to the

CPRLC-B panel (RNC), or directly to the front panel of the plug-in unit

(MGW). If the cabling cabinet is used, the fiber is connected to the

CPLC36 connector panel or to the front panel of the plug-in unit in the

equipment cabinet.


. Connector:

. Duplex LC according to GR-326 and IEC 60874

.

Mating durability for 200 reconnects, insertion loss change 45dB

. Zirconia ferrule

. Efficiency of strain relief > 80N

. UL94V-0

. Boot:

.

90 angle boot (minimum requirement at the MGW or RNCconnection end)

. Maximum installation height 70 mm

. UL94V-0

. Cable:

. 9/125 m single mode fibre

. Attenuation: 0,5 dB / Km at = 1310 nm and 0.4 dB / Km at

= 1550 nm

. Cable must fulfill ITU-T G.652 for interface type STM-1 optical

(ITU-T G.957, table 1)

. Cable must fulfill ATM 155 Mb/s

. Duplex type

. UL VW-1 or UL94V-0

. Fibre cables must be provided with a common secondary

overall jacket which will not slide along the cables

. Maximum cable outer diameter 6.6 mm

. Minimum bending radius during installation < 65 mm

. Minimum bending radius in service < 43 mm (according to IEC

794-1-E11)




87/90

. Crush resistance (briefly) > 500 N/cm. According to IEC 794-1-

E3. Crush resistance (continuous) > 100 N/cm


Table 45. Cable types for single-mode optical cables

Cable type Boot Connection

CSM One end with straight boot and the

other with 90 angle boot

straight

CSMA Both boots are 90 straight

Figure 39. Example of a single-mode optical cable

5.12 1000Base-LX (optical)

Gigabit Ethernet cabling is connected to the IPFGE plug-in unit. If the

cabling cabinet is used, the Ethernet cable is connected to the CPLC36

interface panel.

A

B

30 5

AB

30 5 DN01130619

Dust caps to LC connectors

Dustcaps to LCconnectors





88/90


. Connector

. Duplex LC according to GR-326 and IEC 60874

. Mating durability for 200 reconnects, insertion loss change 45dB

. Zirconia ferrule

. Blue colour

.

Efficiency of strain relief > 80N. UL94V-0

. Boot

. 90 angle boot

. Maximum installation height 70 mm

. UL94V-0

. Cable

. 9/125 m single mode fibre

. Attenuation: 0,5 dB / Km at = 1310 nm and 0.4 dB / Km at

= 1550 nm. Cable must fulfill ITU-T G.652 for interface type STM-1 optical

(ITU-T G.957, table 1)

. Cable must fulfill ATM 155 Mb/s

. Duplex type

. UL VW-1 or UL94V-0

. Fibre cables must be provided with a common secondary

overall jacket which will not slide along the cables

. Maximum cable outer diameter 6.6 mm

. Minimum bending radius during installation < 65 mm

. Minimum bending radius in service < 43 mm (according to IEC

794-1-E11)

. Crush resistance (briefly) > 500 N/cm. According to IEC 794-1-

E3

. Crush resistance (continuous) > 100 N/cm





89/90

Table 46. Cable types for single-mode optical cables

Cable type Boot Connection

CSM One end with straight boot and the

other with 90 angle boot

straight

CSMA Both boots are 90 straight

Figure 40. Example of a single-mode optical cable

5.13 Reference standards and directions

. ATM 155 Mb/s

. EN 50288-2-2

. GR-326

. IEC 332-1

A

B

30 5

AB

30 5 DN01130619

Dust caps to LC connectors

Dustcaps to LCconnectors





90/90

. IEC 332-3

. IEC 754-1

. IEC 794-1

. IEC 874-1

. IEC 60874

. IEC 61754-20-4

. ITU-T G.652

. TIA/EIA-568

. UL94V-0

. UL VW-1

. GR253


cab inter ext cables mgw rnc

Documents