ce 3372 water systems design closed conduit hydraulics-i
TRANSCRIPT
![Page 1: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/1.jpg)
CE 3372 Water Systems Design
Closed Conduit Hydraulics-I
![Page 2: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/2.jpg)
Flow in Closed Conduits
• Diagram• Energy Equation• Head Loss Models
– Pipe loss– Fitting loss
• Moody Chart Problems• Direct Method (Jain equations)• Branched Systems• Looped System
![Page 3: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/3.jpg)
Diagram
![Page 4: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/4.jpg)
Suction Side
Lift Station
Discharge Side
Diagram
![Page 5: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/5.jpg)
Mean Section Velocity
• In most engineering contexts, the mean section velocity is the ratio of the volumetric discharge and cross sectional area.
• The velocity distribution in a section is important in determining frictional losses in a conduit.
€
V =Q
A
![Page 6: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/6.jpg)
Energy Equation
• The energy equation relates the total dynamic head at two points in a system, accounting for frictional losses and any added head from a pump.
![Page 7: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/7.jpg)
Energy Equation
1
2
![Page 8: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/8.jpg)
Head Loss Models
• Darcy-Weisbach• Hazen-Williams• Chezy-Mannings
![Page 9: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/9.jpg)
Darcy-Weisbach• Frictional loss proportional to
– Length, Velocity^2
• Inversely proportional to– Cross sectional area
• Loss coefficient depends on– Reynolds number (fluid and flow properties)– Roughness height (pipe material properties)
![Page 10: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/10.jpg)
Darcy-Weisbach• Frictional loss proportional to
– Length, Velocity^2
• Inversely proportional to– Cross sectional area
• Loss coefficient depends on– Reynolds number (fluid and flow properties)– Roughness height (pipe material properties)
![Page 11: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/11.jpg)
Darcy-Weisbach• DW Head Loss Equation
• DW Equation, Discharge Form, CIRCULAR conduits
![Page 12: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/12.jpg)
Hazen-Williams• Frictional loss proportional to
– Length, Velocity^(1.8)
• Inversely proportional to– Cross section area (as hydraulic radius)
• Loss coefficient depends on– Pipe material and finish
• WATER ONLY!
![Page 13: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/13.jpg)
Hazen-Williams• HW Head Loss
• Discharge Form
![Page 14: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/14.jpg)
Hydraulic Radius• HW is often presented as a velocity equation
using the hydraulic radius
• The hydraulic radius is the ratio of cross section flow area to wetted perimeter
![Page 15: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/15.jpg)
Hydraulic Radius• For circular pipe, full flow (no free surface)
AREAAREA PERIMETERPERIMETER
D
![Page 16: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/16.jpg)
Chezy-Manning
• Frictional loss proportional to– Length, Velocity^2
• Inversely proportional to – Cross section area (as hydraulic radius)
• Loss coefficient depends on– Material, finish
![Page 17: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/17.jpg)
Chezy-Manning
• CM Head Loss
• Discharge form replaces V with Q/A
![Page 18: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/18.jpg)
Fitting (Minor) Losses
• Fittings, joints, elbows, inlets, outlets cause additional head loss.
• Called “minor” loss not because of magnitude, but because they occur over short distances.
• Typical loss model is
![Page 19: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/19.jpg)
Fitting (Minor) Losses
• The loss coefficients are tabulated for different kinds of fittings
![Page 20: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/20.jpg)
Moody Chart
• Moody-Stanton chart is a tool to estimate the friction factor in the DW head loss model
• Used for the pipe loss component of friction
![Page 21: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/21.jpg)
Examples
• Three “classical” examples using Moody Char– Head loss for given discharge, diameter, material– Discharge given head loss, diameter, material– Diameter given discharge, head loss, material
![Page 22: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/22.jpg)
Direct (Jain) Equations
• An alternative to the Moody chart are regression equations that allow direct computation of discharge, diameter, or friction factor.
![Page 23: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/23.jpg)
Branched System• Distribution networks are multi-path pipelines• One topological structure is branching
![Page 24: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/24.jpg)
Branched System• Node
– Inflow = Outflow– Energy is unique value
• Links– Head loss along line
![Page 25: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/25.jpg)
Branched System
Head loss in each pipe
Common head at the node
![Page 26: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/26.jpg)
Branched System
Continuity at the node
![Page 27: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/27.jpg)
Branched System
• 4 Equations, 4 unknowns• Non-linear so solve by
– Newton-Raphson/Quasi-Linearization
• Quadratic in unknown, so usually can find solution in just a few iterations
![Page 28: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/28.jpg)
Looped System• Looped system is extension of branching
where one or more pipes rejoin at a different node.
![Page 29: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/29.jpg)
Looped System• Nodes:
– Inflow = Outflow– Energy Unique
• Links– Head loss along pipe– Head loss in any loop is zero
LOOP
![Page 30: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/30.jpg)
Examples
• Branched System• Loop System
![Page 31: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/31.jpg)
Hydraulic Grade Line
• Hydraulic grade line is a plot along a conduit profile of the sum of elevation and pressure head at a location.
• It is where a free surface would exist if there were a piezometer installed in the pipeline
![Page 32: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/32.jpg)
Energy Grade Line
• Hydraulic grade line is a plot along a conduit profile of the sum of elevation, pressure, and velocity head at a location.
![Page 33: CE 3372 Water Systems Design Closed Conduit Hydraulics-I](https://reader035.vdocuments.net/reader035/viewer/2022062314/56649e7b5503460f94b7d406/html5/thumbnails/33.jpg)
HGL/EGL