civil products -...
TRANSCRIPT
NRI-U is advancing knowledge,training, and understanding ofcomposite repair systems
R&D is patenting tomorrow’scomposite technology today
From FREE Engineering Support,to installation oversight, we make sure jobs are done right
For repair of structural concrete including columns, beams, and slabsUni-axial carbon fiber fabric, saturated with two-part, Titan® Saturant EpoxyUni-directional fabric with primary, continuous fibers oriented in the 0° directionDesigned for use in wide variety of environmentsHigh chemical resistance and high temperature ratingsConforms to ACI440 standards for non-metallic composite reinforcing solutionsfor concreteTitan 118 is an ICC-ES ESR-3548 listed product
®
For repair of structural concrete including columns, beams, and slabsUnique, bi-axial carbon fiber fabric, saturated with Titan Saturant EpoxyTitan® 218 carbon fiber is oriented in the 0° / 90° directions with the 0° directionbeing the primary, continuous fibersDesigned for use in wide variety of environmentsHigh chemical resistance and high temperature ratingsConforms to ACI440 standards for non-metallic composite reinforcing solutionsfor concrete
®
Two-part, 100% solids epoxy designed for composite laminate repair in combi-nation with our Titan® infrastructure repair systemDesigned to conform to ACI440 standards for nonmetallic composite reinforcingsolution of concreteEpoxy system provides high tensile values using fiberglass or carbon fiber laminates
®
Titan®-Top Coat is an aesthetically pleasing epoxy coating which provides afinal protective layer over the Titan® structural repair system.
CIVIL PRODUCTS
I n n o v a t i v e C o r r o s i o n C o n t r o l
Tel : +603-3884 9680 Fax: 1700 810 [email protected] / [email protected]
InnoCorr Offshore Sdn Bhd(1058983-K)
Description
Flare lines, blow down lines, steam piping, coolingwater linesGirth welds, elbows, teesChemical processing linesReinforced coating for elevated temperaturesCorrosion repairAnywhere elevated temperatures are of expected
Typical Applications
VOCs: NonePot Life: 75 Minutes @ 75°F (24°C)Working Time: 45 Minutes @ 75°F (24°C)Gel Time: Approx. 161 Minutes @ 70°F (21°C)Cure Time: Approx. 18 Hours @ 75°F (24°C)Service Temperature: < 300°F (149°C)Application Temperature: 50 to 200°F (5 to 93°C)Solids Content: 100%Shelf Life: 12 Months with recommended storage methods
Installation Properties
Engineered, highly conformable, bi-directionalfiberglass using NRI's patented inspectable Ther-mo-Poxy™ epoxy
High Temperature, non-hazardous, chemicallyresistant system
Easily monitored through radiographic inspection
Operator Qualified (OQ), designed to ASMEPCC-2, ASME B31, ISO TS24817, DOT, API, CSAZ662 standards
Inspectable with radiographyHigh temperature rating with an ambient-cured epoxyNo heating or post-curing requiredFull factory engineering, calculations, and supportCode compliantPatented polymer inspection capabilityNon-woven architecture allows for scalable increases in ply thickness
Surface PreparationFiller MaterialPrimerFiber
SSPC-SP 11 (1-3 mil profile)Thermo-Fill HT
Thermo-Poxy InspectableFiberglass
Thermo-Wrap InspectableSystem
Inspectable High Temperature Fiberglass Epoxy System
Two-part, titanium-reinforced epoxy puttyDesigned to bond and repair materials exposed to high temperaturesWill not drip or sag; non-toxic, non-hazardous & non-flammableWhen fully cured, resistant to hydrocarbons, ketones, alcohols, esters,halocarbons, aqueous salt solutions, and dilute acids and bases
Two-part, steel-reinforced epoxy puttyCures in minutes, will not drip or sag, will set on wet surfacesNon-toxic: NSF 61 and BS6920 approved for use with potable waterCan repair virtually any surface including metals, masonry, wood, ceramic,glass, and plasticsResistant to hydrocarbons, ketones, alcohols, esters, halocarbons,aqueous salt solutions, dilute acids and basesNon-hazardous & non-flammable system
Two-part carbon nanotube-reinforced epoxy filler Bonds to materials exposed to temperatures up to 300°F (149°C) Non-toxic, non-hazardous & non-flammable systemWhen fully cured, resistant to hydrocarbons, ketones, alcohols, esters,halocarbons, aqueous salt solutions, and dilute acids and bases
FILLERS
Two-part epoxy compound that cures quickly at ambient temperaturesHigh compressive strength and bond make it excellent for repairing pittedmetal and steel subjected to high pressureResistant to many solvents, hydrocarbons, and adverse environmentsNon-hazardous & non-flammable system
I n n o v a t i v e C o r r o s i o n C o n t r o l
Tel : +603-3884 9680 Fax: 1700 810 [email protected] / [email protected]
www.innocorroffshore.com
InnoCorr Offshore Sdn Bhd(1058983-K)
Unique blend of liquid epoxy, polymer, and aliphatic polyamine curing agentsthat is able to displace water from wet surfacesIncorporates Kevlar® fibers for reinforcement and viscosity managementExcellent adhesion, highly resistant to high pressures, temperature extremes,and chemicals and petroleum productsCan be applied above- or below-gradeShips non-regulated by USDOT, IATA, IMOISO 12944 High Durability Qualified
System protects composites installed in areas requiring fire proofingCreates a low-conductivity thermal barrier between the composite repair'souter layer and an external flamePrevents composite from reaching maximum temperature rating and degra-ding or failing
Designed to prevent corrosion or abrasion damage on pipe support areasEliminates the need to paint future hard to reach areasCan be used in immersion and above- or below-gradeCan be used for corrosion/abrasion prevention on steel (carbon and stain-less), galvanized metal, concrete, fiberglass-reinforced pipe (FRP), iron, PVC,and wood
Designed to seal pipeline leaks in conjunction with engineered compositesystemsPowder-coated carbon steel with an internal rubber patch3.5" wide and available in lengths designed for diameters from 2" to 8"Clamps may be linked together to seal pipe diameters up to 24"
PRODUCTS
Description
Flare linesSteam pipingGirth welds, elbows, teesChemical processing linesAnywhere elevated temperatures are of concern or expected
Typical Applications
Engineered carbon fiber composite system utilizinghigh-strength, bi-axial hybrid carbon and glass fiberwith NRI's patented Thermo-Poxy epoxy
Designed to repair and restore substrates operatingat elevated temperatures, while still curing at room temperature
Operator Qualified (OQ) engineered system wasdesigned to conform to and is recognized by ASMEPCC-2, ASME B31, ISO TS24817, DOT, API, andCSA Z662 standards for nonmetallic reinforcingsolutions
High temperature rating with an ambient-cured epoxyNo heating or post-curing requiredFull factory engineering calculations, and supportNon-hazardousHigh flash pointHigh tensile strength and stiffness
VOCs: NonePot Life: 75 Minutes @ 75°F (24°C)Working Time: 45 Minutes @ 75°F (24°C)Gel Time: Approx. 161 Minutes @ 70°F (21°C)Cure Time: Approx. 18 Hours @ 75°F (24°C)Service Temperature: Max: Up to 300°F (149°C)Application Temperature: 50 to 200°F (5 to 93°C)Solids Content: 100%Shelf Life: 12 Months with recommended storage methods
Installation Properties
High Temperature Carbon Fiber Epoxy System
Surface PreparationFiller MaterialPrimerFiber
SSPC-SP 11 (1-3 mil profile)Thermo-Fill HTThermo-Poxy
Carbon fiber & fiberglass
Thermo-Wrap CFSystem
Tel : +603-3884 9680 Fax: 1700 810 [email protected] / [email protected]
InnoCorr Offshore Sdn Bhd(1058983-K)
PRODUCTS
Unique, moisture-cured, bi-directional compositedesigned to repair and reinforce internal and exter-nal corrosion on structures and pipelines
Our pre-preg system ensures proper fiber-to-resincontent ratios
Operator Qualified (OQ) engineered system wasdesigned to conform to ASME PCC-2, ASME B31,ISO TS24817, DOT, API and CSA Z662 standardsfor nonmetallic reinforcing solutions
Repair and reinforce virtually any geometry in minu-tes
Description
Extreme Strength Fiberglass Composite System
Pipeline IntegrityTransmission and distribution pipelinesOil and gas risersGirth welds on vessels and pipelinesStraights, elbows, tees, nozzles, and flangesProcess piping: chemicals, oil, gases, water, steamAtmospheric corrosion
Typical Applications
VOC: NoneWorking Time: 30 minutes 75°F (24°C)Set Time: 2 Hours 75°F (24°C)Resin Type: Water-activated, polyurethaneResin Application: Micro-controlled, Pre-pregService Temperature: -50° to 194°F (4° to 65°C)Application Temperature: 40° to 150°F (4° to 65°C)Shelf Life: 12 months with recommended storage
Installation Properties
Surface PreparationFiller MaterialPrimerFiber
SSPC-SP 11 (1-3 mil profile)Syntho-Poxy HC
Syntho-Sub-Sea LVFiberglass
Syntho-Glass XTSystem
Water-activated polyurethane resin reduces composite preparation time by 50%Installs in wet, rainy, or submerged environments ensures application in virtually any situationFlexibility permits application on odd geometries while eliminating diameter specific inventoryFull factory engineering consultation and support, ensuring safe and successful repairs
Designed to mitigate splash zone corrosion and impactTwo layer, two component system: Syntho-Glass and petrolatum tapeProvides long-term mechanical and corrosion protection for pipes, flanges,valves, and related surfacesPre-preg system designed to offer solution for corrosion, insulation andwaterproofing problems
Repairs non-leaking natural gas risers exhibiting wall loss up to 80% at<300psi (20.7bar)Eliminates atmospheric corrosion in accordance with Distribution IntegrityManagement Programs (DIMP)8 layers allows the repair of corroded piping or risers without shut-down orreplacementConforms to ASME PCC-2, ASME B31, ISO TS24817, DOT, API, and CSAZ662 standards for non-metallic reinforcing solutions
Live natural gas repair system permanently seals active leaks up to 60psi (4 bar) without interruption to serviceThird-party testing for long-term pressure retention has been conducted at90psi (6bar)
Protects field joint coatings from abrasion, stresses, and scarring of direc-tional drilling, HDD, and boringCreates abrasion-resistant, sacrificial outer laminate to protect pre-appro-ved coatings including epoxies, shrink sleeves, and cold/hot-applied tapesControlled set-times and extreme conformability provide fast installs in any environment
I n n o v a t i v e C o r r o s i o n C o n t r o l
Tel : +603-3884 9680 Fax: 1700 810 [email protected] / [email protected]
www.innocorroffshore.com
InnoCorr Offshore Sdn Bhd(1058983-K)
PRODUCTS
Syntho-Glass UP and NP Repair Systems were designed for leak repair appli-cations on copper, steel, stainless steel (SS), PVC, fiberglass-reinforced pipe(FRP), concrete, rubber, and moreCombine Syntho-Glass & Syntho-Steel to repair joints, couplings, and leaksSyntho-Glass UP was designed to repair active leaks up to 60psiSyntho-Glass NP was designed to repair non-active leaks up to 300psi
Aesthetically pleasing, non-yellowing composite providing UV stabilization forpipe coatings, where UV degradation is of concernPrevents future corrosion/abrasion due to mechanical impact, freeze/thawand frost heave, soil-to-air/water-to-air corrosion, crevice corrosion, galvaniccorrosionCan be used in immersion, or on below- or above-ground pipes and piles
UV
Fiberglass, pre-impregnated composite, activated by salt or fresh waterRepair/reinforce virtually any low psi pipe in minutesInitial setting time of 30 minutes (75°F/24°C), on copper, steel, Stainless Steel(SS), PVC, Fiber Reinforced Pipe (FRP), clay, concrete, rubber, and more
Extremely conformable, thin, flexible and lightweightFiberglass, pre-impregnated composite, activated by salt or fresh waterRepair/reinforce virtually any low psi pipe in minutesInitial setting time of only 30 minutes (75°F/24°C), on copper, steel, Stainless Steel (SS), PVC glue joints, Fiber Reinforced Pipe (FRP), clay, concrete,rubber, and more
Description
Transmission and distribution pipelinesOil and gas risersMechanical dents and defectsGirth welds on vessels and pipelinesStraights, elbows, tees, and flangesProcess piping: chemicals, oil, gases, water,and steam
Typical Applications
First bi-axial hybrid carbon and fiberglass polyuretha-ne moisture-cured system, blending carbon's streng-th/stiffness with the ease-of-use of moisture-curedpre-preg, reducing installation time and cost
Operator Qualified (OQ), designed to ASME PCC-2,ASME B31, ISO TS24817, DOT, API, CSA Z662 stan-dards
Can be applied in splash zone, sweating, or surfacecondensation applications
Moisture-cure allows for subsea and wet environmentapplications
Conforms to all diameters, shapes, welds, and irregu-lar geometries
Water-activated polyurethane resin reduces composite preparation time by over 50%Installation in wet, rainy, or submerged environments ensures ease of application Full factory engineering consultation support,ensuring safe and successful repairsVOCs: None
Working Time: 30 Minutes at 75°F (24°C)Set Time: 2 Hours at 75°F (24°C)Resin Type: Water-activated polyurethaneResin Application: Micro-controlled, Pre-impregnatedService Temperature: -50° to 194°F (-46° to 90° C)Application Temperature: 32° to 150°F (-18° to 65°C)Shelf Life: 12 Months with proper storage conditions
Installation Properties
Carbon Fiber Composite Reinforcement System
Surface PreparationFiller MaterialPrimerFiber
SSPC-SP 11 (1-3 mil profile)Syntho-Poxy HC
Syntho-Sub-Sea LVCarbon fiber & fiberglass
Viper-SkinSystem
Tel : +603-3884 9680 Fax: 1700 810 [email protected] / [email protected]
InnoCorr Offshore Sdn Bhd(1058983-K)
Description
Prevent future corrosion and abrasion due to:soil-to-air corrosion, splash zone corrosion, crevicecorrosion, galvanic corrosion, freeze/thaw and frost/heave cycles
Transmission and Distribution PipelinesProcess PipingOil and Gas RisersGirth welds, elbows, tees, nozzles, flanges, andstraights
Typical Applications
The Syntho-Glass® line of products are patented anddesigned to repair and reinforce pipes, pipelines, andstructures including timber piles, damaged by soil-to-airand/or splash zone corrosion
Fiber-reinforced polymer (FRP) systems incorporateepoxy, urethane, and resins in combination with glassand carbon fiber for unparalleled strength, durability, and chemical-resistance
Pre-impregnated composites save time and reducecosts, while ensuring proper fiber-to-resin ratio
Water-activated composite systems reduce preparation time by 50%Easily install in wet, rainy, or submerged environmentsApply to virtually any shape or geometryFull factory engineering consultation and support
Engineering ServicesStructural analysis and design of projectsDetailed design proposals with every projectProject-specific method statements and Quality Control (QC) hold points
SOIL-TO-AIR & SPLASH ZONECORROSION
Description
Full tank rehabilitationStructural retrofittingPatch repairTank roof repairsEnvironmental protection
Typical Applications
Composite repairs provide optimal solutions for therepair or retrofit of tanks and vessels
High-strength, low-weight, conform to any shape,while maintaining structural integrity over widerange of temperatures and environments
NRI's ISO09001 quality manufacturing programensures consistent material
Trained, in-house engineering support
On-demand Finite Element Analysis (FEA)
Quick external patchLong term lifeNumerous product options for diverse application scenariosFull factory engineering calculations, consultation, and support ensuring safe and successful repairs
TANK REHABILITATION
Engineering ServicesStructural analysis & designANSYS FEA Modeling softwareDetailed design proposalsProject-specific method statements and Quality Control (QC) hold points
I n n o v a t i v e C o r r o s i o n C o n t r o l
Tel : +603-3884 9680 Fax: 1700 810 [email protected]
InnoCorr Offshore Sdn Bhd(1058983-K)
Description
Prevent future corrosion and abrasion due to:soil-to-air corrosion, splash zone corrosion, crevicecorrosion, galvanic corrosion, freeze/thaw and frost/heave cycles
Transmission and Distribution PipelinesProcess PipingOil and Gas RisersGirth welds, elbows, tees, nozzles, flanges, andstraights
Typical Applications
The Syntho-Glass® line of products are patented anddesigned to repair and reinforce pipes, pipelines, andstructures including timber piles, damaged by soil-to-airand/or splash zone corrosion
Fiber-reinforced polymer (FRP) systems incorporateepoxy, urethane, and resins in combination with glassand carbon fiber for unparalleled strength, durability, and chemical-resistance
Pre-impregnated composites save time and reducecosts, while ensuring proper fiber-to-resin ratio
Water-activated composite systems reduce preparation time by 50%Easily install in wet, rainy, or submerged environmentsApply to virtually any shape or geometryFull factory engineering consultation and support
Engineering ServicesStructural analysis and design of projectsDetailed design proposals with every projectProject-specific method statements and Quality Control (QC) hold points
SOIL-TO-AIR & SPLASH ZONECORROSION
Description
Full tank rehabilitationStructural retrofittingPatch repairTank roof repairsEnvironmental protection
Typical Applications
Composite repairs provide optimal solutions for therepair or retrofit of tanks and vessels
High-strength, low-weight, conform to any shape,while maintaining structural integrity over widerange of temperatures and environments
NRI's ISO09001 quality manufacturing programensures consistent material
Trained, in-house engineering support
On-demand Finite Element Analysis (FEA)
Quick external patchLong term lifeNumerous product options for diverse application scenariosFull factory engineering calculations, consultation, and support ensuring safe and successful repairs
TANK REHABILITATION
Engineering ServicesStructural analysis & designANSYS FEA Modeling softwareDetailed design proposalsProject-specific method statements and Quality Control (QC) hold points
I n n o v a t i v e C o r r o s i o n C o n t r o l
Tel : +603-3884 9680 Fax: 1700 810 [email protected]
InnoCorr Offshore Sdn Bhd(1058983-K)
PRODUCTS
Syntho-Glass UP and NP Repair Systems were designed for leak repair appli-cations on copper, steel, stainless steel (SS), PVC, fiberglass-reinforced pipe(FRP), concrete, rubber, and moreCombine Syntho-Glass & Syntho-Steel to repair joints, couplings, and leaksSyntho-Glass UP was designed to repair active leaks up to 60psiSyntho-Glass NP was designed to repair non-active leaks up to 300psi
Aesthetically pleasing, non-yellowing composite providing UV stabilization forpipe coatings, where UV degradation is of concernPrevents future corrosion/abrasion due to mechanical impact, freeze/thawand frost heave, soil-to-air/water-to-air corrosion, crevice corrosion, galvaniccorrosionCan be used in immersion, or on below- or above-ground pipes and piles
UV
Fiberglass, pre-impregnated composite, activated by salt or fresh waterRepair/reinforce virtually any low psi pipe in minutesInitial setting time of 30 minutes (75°F/24°C), on copper, steel, Stainless Steel(SS), PVC, Fiber Reinforced Pipe (FRP), clay, concrete, rubber, and more
Extremely conformable, thin, flexible and lightweightFiberglass, pre-impregnated composite, activated by salt or fresh waterRepair/reinforce virtually any low psi pipe in minutesInitial setting time of only 30 minutes (75°F/24°C), on copper, steel, Stainless Steel (SS), PVC glue joints, Fiber Reinforced Pipe (FRP), clay, concrete,rubber, and more
Description
Transmission and distribution pipelinesOil and gas risersMechanical dents and defectsGirth welds on vessels and pipelinesStraights, elbows, tees, and flangesProcess piping: chemicals, oil, gases, water,and steam
Typical Applications
First bi-axial hybrid carbon and fiberglass polyuretha-ne moisture-cured system, blending carbon's streng-th/stiffness with the ease-of-use of moisture-curedpre-preg, reducing installation time and cost
Operator Qualified (OQ), designed to ASME PCC-2,ASME B31, ISO TS24817, DOT, API, CSA Z662 stan-dards
Can be applied in splash zone, sweating, or surfacecondensation applications
Moisture-cure allows for subsea and wet environmentapplications
Conforms to all diameters, shapes, welds, and irregu-lar geometries
Water-activated polyurethane resin reduces composite preparation time by over 50%Installation in wet, rainy, or submerged environments ensures ease of application Full factory engineering consultation support,ensuring safe and successful repairsVOCs: None
Working Time: 30 Minutes at 75°F (24°C)Set Time: 2 Hours at 75°F (24°C)Resin Type: Water-activated polyurethaneResin Application: Micro-controlled, Pre-impregnatedService Temperature: -50° to 194°F (-46° to 90° C)Application Temperature: 32° to 150°F (-18° to 65°C)Shelf Life: 12 Months with proper storage conditions
Installation Properties
Carbon Fiber Composite Reinforcement System
Surface PreparationFiller MaterialPrimerFiber
SSPC-SP 11 (1-3 mil profile)Syntho-Poxy HC
Syntho-Sub-Sea LVCarbon fiber & fiberglass
Viper-SkinSystem
Tel : +603-3884 9680 Fax: 1700 810 [email protected] / [email protected]
InnoCorr Offshore Sdn Bhd(1058983-K)
PRODUCTS
Unique, moisture-cured, bi-directional compositedesigned to repair and reinforce internal and exter-nal corrosion on structures and pipelines
Our pre-preg system ensures proper fiber-to-resincontent ratios
Operator Qualified (OQ) engineered system wasdesigned to conform to ASME PCC-2, ASME B31,ISO TS24817, DOT, API and CSA Z662 standardsfor nonmetallic reinforcing solutions
Repair and reinforce virtually any geometry in minu-tes
Description
Extreme Strength Fiberglass Composite System
Pipeline IntegrityTransmission and distribution pipelinesOil and gas risersGirth welds on vessels and pipelinesStraights, elbows, tees, nozzles, and flangesProcess piping: chemicals, oil, gases, water, steamAtmospheric corrosion
Typical Applications
VOC: NoneWorking Time: 30 minutes 75°F (24°C)Set Time: 2 Hours 75°F (24°C)Resin Type: Water-activated, polyurethaneResin Application: Micro-controlled, Pre-pregService Temperature: -50° to 194°F (4° to 65°C)Application Temperature: 40° to 150°F (4° to 65°C)Shelf Life: 12 months with recommended storage
Installation Properties
Surface PreparationFiller MaterialPrimerFiber
SSPC-SP 11 (1-3 mil profile)Syntho-Poxy HC
Syntho-Sub-Sea LVFiberglass
Syntho-Glass XTSystem
Water-activated polyurethane resin reduces composite preparation time by 50%Installs in wet, rainy, or submerged environments ensures application in virtually any situationFlexibility permits application on odd geometries while eliminating diameter specific inventoryFull factory engineering consultation and support, ensuring safe and successful repairs
Designed to mitigate splash zone corrosion and impactTwo layer, two component system: Syntho-Glass and petrolatum tapeProvides long-term mechanical and corrosion protection for pipes, flanges,valves, and related surfacesPre-preg system designed to offer solution for corrosion, insulation andwaterproofing problems
Repairs non-leaking natural gas risers exhibiting wall loss up to 80% at<300psi (20.7bar)Eliminates atmospheric corrosion in accordance with Distribution IntegrityManagement Programs (DIMP)8 layers allows the repair of corroded piping or risers without shut-down orreplacementConforms to ASME PCC-2, ASME B31, ISO TS24817, DOT, API, and CSAZ662 standards for non-metallic reinforcing solutions
Live natural gas repair system permanently seals active leaks up to 60psi (4 bar) without interruption to serviceThird-party testing for long-term pressure retention has been conducted at90psi (6bar)
Protects field joint coatings from abrasion, stresses, and scarring of direc-tional drilling, HDD, and boringCreates abrasion-resistant, sacrificial outer laminate to protect pre-appro-ved coatings including epoxies, shrink sleeves, and cold/hot-applied tapesControlled set-times and extreme conformability provide fast installs in any environment
I n n o v a t i v e C o r r o s i o n C o n t r o l
Tel : +603-3884 9680 Fax: 1700 810 [email protected] / [email protected]
www.innocorroffshore.com
InnoCorr Offshore Sdn Bhd(1058983-K)
Unique blend of liquid epoxy, polymer, and aliphatic polyamine curing agentsthat is able to displace water from wet surfacesIncorporates Kevlar® fibers for reinforcement and viscosity managementExcellent adhesion, highly resistant to high pressures, temperature extremes,and chemicals and petroleum productsCan be applied above- or below-gradeShips non-regulated by USDOT, IATA, IMOISO 12944 High Durability Qualified
System protects composites installed in areas requiring fire proofingCreates a low-conductivity thermal barrier between the composite repair'souter layer and an external flamePrevents composite from reaching maximum temperature rating and degra-ding or failing
Designed to prevent corrosion or abrasion damage on pipe support areasEliminates the need to paint future hard to reach areasCan be used in immersion and above- or below-gradeCan be used for corrosion/abrasion prevention on steel (carbon and stain-less), galvanized metal, concrete, fiberglass-reinforced pipe (FRP), iron, PVC,and wood
Designed to seal pipeline leaks in conjunction with engineered compositesystemsPowder-coated carbon steel with an internal rubber patch3.5" wide and available in lengths designed for diameters from 2" to 8"Clamps may be linked together to seal pipe diameters up to 24"
PRODUCTS
Description
Flare linesSteam pipingGirth welds, elbows, teesChemical processing linesAnywhere elevated temperatures are of concern or expected
Typical Applications
Engineered carbon fiber composite system utilizinghigh-strength, bi-axial hybrid carbon and glass fiberwith NRI's patented Thermo-Poxy epoxy
Designed to repair and restore substrates operatingat elevated temperatures, while still curing at room temperature
Operator Qualified (OQ) engineered system wasdesigned to conform to and is recognized by ASMEPCC-2, ASME B31, ISO TS24817, DOT, API, andCSA Z662 standards for nonmetallic reinforcingsolutions
High temperature rating with an ambient-cured epoxyNo heating or post-curing requiredFull factory engineering calculations, and supportNon-hazardousHigh flash pointHigh tensile strength and stiffness
VOCs: NonePot Life: 75 Minutes @ 75°F (24°C)Working Time: 45 Minutes @ 75°F (24°C)Gel Time: Approx. 161 Minutes @ 70°F (21°C)Cure Time: Approx. 18 Hours @ 75°F (24°C)Service Temperature: Max: Up to 300°F (149°C)Application Temperature: 50 to 200°F (5 to 93°C)Solids Content: 100%Shelf Life: 12 Months with recommended storage methods
Installation Properties
High Temperature Carbon Fiber Epoxy System
Surface PreparationFiller MaterialPrimerFiber
SSPC-SP 11 (1-3 mil profile)Thermo-Fill HTThermo-Poxy
Carbon fiber & fiberglass
Thermo-Wrap CFSystem
Tel : +603-3884 9680 Fax: 1700 810 [email protected] / [email protected]
InnoCorr Offshore Sdn Bhd(1058983-K)
Description
Flare lines, blow down lines, steam piping, coolingwater linesGirth welds, elbows, teesChemical processing linesReinforced coating for elevated temperaturesCorrosion repairAnywhere elevated temperatures are of expected
Typical Applications
VOCs: NonePot Life: 75 Minutes @ 75°F (24°C)Working Time: 45 Minutes @ 75°F (24°C)Gel Time: Approx. 161 Minutes @ 70°F (21°C)Cure Time: Approx. 18 Hours @ 75°F (24°C)Service Temperature: < 300°F (149°C)Application Temperature: 50 to 200°F (5 to 93°C)Solids Content: 100%Shelf Life: 12 Months with recommended storage methods
Installation Properties
Engineered, highly conformable, bi-directionalfiberglass using NRI's patented inspectable Ther-mo-Poxy™ epoxy
High Temperature, non-hazardous, chemicallyresistant system
Easily monitored through radiographic inspection
Operator Qualified (OQ), designed to ASMEPCC-2, ASME B31, ISO TS24817, DOT, API, CSAZ662 standards
Inspectable with radiographyHigh temperature rating with an ambient-cured epoxyNo heating or post-curing requiredFull factory engineering, calculations, and supportCode compliantPatented polymer inspection capabilityNon-woven architecture allows for scalable increases in ply thickness
Surface PreparationFiller MaterialPrimerFiber
SSPC-SP 11 (1-3 mil profile)Thermo-Fill HT
Thermo-Poxy InspectableFiberglass
Thermo-Wrap InspectableSystem
Inspectable High Temperature Fiberglass Epoxy System
Two-part, titanium-reinforced epoxy puttyDesigned to bond and repair materials exposed to high temperaturesWill not drip or sag; non-toxic, non-hazardous & non-flammableWhen fully cured, resistant to hydrocarbons, ketones, alcohols, esters,halocarbons, aqueous salt solutions, and dilute acids and bases
Two-part, steel-reinforced epoxy puttyCures in minutes, will not drip or sag, will set on wet surfacesNon-toxic: NSF 61 and BS6920 approved for use with potable waterCan repair virtually any surface including metals, masonry, wood, ceramic,glass, and plasticsResistant to hydrocarbons, ketones, alcohols, esters, halocarbons,aqueous salt solutions, dilute acids and basesNon-hazardous & non-flammable system
Two-part carbon nanotube-reinforced epoxy filler Bonds to materials exposed to temperatures up to 300°F (149°C) Non-toxic, non-hazardous & non-flammable systemWhen fully cured, resistant to hydrocarbons, ketones, alcohols, esters,halocarbons, aqueous salt solutions, and dilute acids and bases
FILLERS
Two-part epoxy compound that cures quickly at ambient temperaturesHigh compressive strength and bond make it excellent for repairing pittedmetal and steel subjected to high pressureResistant to many solvents, hydrocarbons, and adverse environmentsNon-hazardous & non-flammable system
I n n o v a t i v e C o r r o s i o n C o n t r o l
Tel : +603-3884 9680 Fax: 1700 810 [email protected] / [email protected]
www.innocorroffshore.com
InnoCorr Offshore Sdn Bhd(1058983-K)
NRI-U is advancing knowledge,training, and understanding ofcomposite repair systems
R&D is patenting tomorrow’scomposite technology today
From FREE Engineering Support,to installation oversight, we make sure jobs are done right
For repair of structural concrete including columns, beams, and slabsUni-axial carbon fiber fabric, saturated with two-part, Titan® Saturant EpoxyUni-directional fabric with primary, continuous fibers oriented in the 0° directionDesigned for use in wide variety of environmentsHigh chemical resistance and high temperature ratingsConforms to ACI440 standards for non-metallic composite reinforcing solutionsfor concreteTitan 118 is an ICC-ES ESR-3548 listed product
®
For repair of structural concrete including columns, beams, and slabsUnique, bi-axial carbon fiber fabric, saturated with Titan Saturant EpoxyTitan® 218 carbon fiber is oriented in the 0° / 90° directions with the 0° directionbeing the primary, continuous fibersDesigned for use in wide variety of environmentsHigh chemical resistance and high temperature ratingsConforms to ACI440 standards for non-metallic composite reinforcing solutionsfor concrete
®
Two-part, 100% solids epoxy designed for composite laminate repair in combi-nation with our Titan® infrastructure repair systemDesigned to conform to ACI440 standards for nonmetallic composite reinforcingsolution of concreteEpoxy system provides high tensile values using fiberglass or carbon fiber laminates
®
Titan®-Top Coat is an aesthetically pleasing epoxy coating which provides afinal protective layer over the Titan® structural repair system.
CIVIL PRODUCTS
I n n o v a t i v e C o r r o s i o n C o n t r o l
Tel : +603-3884 9680 Fax: 1700 810 [email protected] / [email protected]
InnoCorr Offshore Sdn Bhd(1058983-K)