cm16 r8 blk/dst - amazon web services · 2015-10-03 · cm16 r8 blk/dst instruction manual all...
TRANSCRIPT
Automatic firingSingle shotSafety On Semi Auto Full Auto
The trigger cannot be pulled
Rail System
Reinforced Grip
Selector Lever
Flash Suppressor
Outer Barrel
Hi-Cap 300R Magazine
Extend Battery Stock
Stock Release Lever
Trigger
Charging Handle
30mm AP Red Dot Sight
Dust Cover
Pull out the wire connector.Squeeze the tabs and remove the butt plate.
1.Charge up the battery. 2.Charging will be complete after 3 hours.
Remove the battery stop. Connect the battery plug with the connector until you hear a click.
Insert the battery into the stock. Reinstall the battery cover and the butt plate.
Do not catch your fingers in the dummy bolt.Never hold the gun sideways as the BB pellets will curve right or left.
Best Direction.
Too much Hop-up.( Turn the adjust lever toward Normal )
Not enough Hop-up. ( Turn the adjust lever toward Hop )or Too much Hop-up. ( Turn the adjust lever toward Normal )
Click
Click
Turn to Normal Turn to Hop
Product appearance depends on actual goods
It is strongly recommended the use of G&G BB pellets only. Using low quality BB pellets will damage the product and void warranty.
WWW.GUAY2.COM Printed in TaiwanManufactured by G&G Armament
Hi-Cap 300R Magazine
CM16 R8 BLK/DSTCM16 R8 BLK/DSTINSTRUCTION MANUAL All G&G products are complied with CE and ROHS 2.0.
G&G Armament is also certified manufacturer of ISO 9001.
Please use quality battery with the CE approval, to avoid any unnecessary damage on the product.Please use either recommended batteries. Defected or low quality batteries might damage the product.Remove the battery from the product when it is not in use.Do not wet nor incinerate the battery, nor to deform the terminal.
1.
2.
3.
4.
Open the magazine top plate.
Pour G&G 5.95mm BBs into the chamber and close the plate when the chamber is full.
Turn the winding wheel on the bottom of the magazine to tighten the spring. This will allow the BBs to feed through the top of the magazine.
Insert the magazine into the Airsoft gun until it click into place.
SETTING MAGAZINE
FIRING MODE & SAFETY
BATTERY SETTING
HOP-UP ADJUSTMENT
► You may purchase all of the groups’ parts from G&G support Dep.
► E-Mail: support@guay2com
CM16 R8- 01
CM16 R8- 02
CM16 R8- 03
CM16 R8- 04
CM16 R8- 05
CM16 R8- 06CM16 R8- 07CM16 R8- 08
CM16 R8- 09
CM16 R8- 10
CM16 R8- 11
CM16 R8- 13
CM16 R8- 14
CM16 R8- 12
CM16 R8- 01CM16 R8- 02CM16 R8- 03CM16 R8- 04CM16 R8- 05CM16 R8- 06CM16 R8- 07
CM16 R8- 08CM16 R8- 09CM16 R8- 10CM16 R8- 11CM16 R8- 12CM16 R8- 13CM16 R8- 14
Flash suppressor set
Rail system set
Outer barrel set
Lower receiver set
Hi-cap 300R magazine
Grip & Motor set
Extended stock set
Enhanced rod set
Inner barrel
Hop-up set
Upper receiver set
Gear box set
Charging handle set
30mm AP Red dot sight
1
1
1
2
2
67
8910
111213
14
15
1
13
4
6
1
2
4
4
5
13
4
2
6
7
8
9
10
11
12
3
78
9
10
5
2
1
2
23
45
23
46
789
10
1315
16
14
17
2
1
1
2
1
3
2
3
4 4
5
6
78
910
11
3
4
8
5
6
7
18
1112
5
TAIWAN
Tel : +886-2-2692-2000 Fax : +886-2-2692-400011F-3., No.27, Lane 169, Kangning St. Shijr City, Taipei County 22180, Taiwan (R.O.C.)
Taipei
Tel : +886-4-798-9000 Fax : +886-4-798-9900No.999, Zhonghua Rd. Shengang Township, Changhua County 50955, Taiwan (R.O.C.)
ChangHua
Headquarter
Sales Dept. [email protected] , [email protected] Support Dept. [email protected] Dept. [email protected]
U.S.A.
Tel : +1-626-581-0101 Fax : +1-626-581-10111122 Coiner Court, City of Industry, CA 91748 (U.S.A.)
LosAngeles
E-mail [email protected]
Dealer
G2-201401-06-英
Press the stock release lever to unlock.
Adjust the position ( 6 position ).
Turn the flash suppressor clockwise to disassemble it.
Turn the flash suppressor counterclockwise to assemble it.
Detachable red dot sight. Turn the knobs counterclockwise to disassemble the red dot sight.
Take off the red dot sight to install other accessories.
Install the carbine visible laser . Install the handguard panel. Install the R.I.S. forward grip.
Remove the magazine. Return the hop up dial to normal position and insert the cleaning rod from the lead edge of the inner barrel.
Be aware to have the rod facing down and reaching to the end, and remove clogged pellets.
The screw at bottom of the grip.Please use the screwdriver to adjust.
Check the wire set contact with motor.
Check the battery and connector.
CM16 R8 BLK/DSTCM16 R8 BLK/DSTINSTRUCTION MANUAL
Adjust screw when the gear noise becomes shrilly.
No operation No operation
RETRACTABLE STOCK MOVABLE PARTS MAINTENANCE
OPTIONAL FLASH SUPPRESSOR OPTIONAL ACCESSORIES TROUBLE SHOOTING
PARTS LIST