commercial door 1900 light-duty commercial grade … · 2018. 10. 11. · dbci’s commercial steel...

I ntegr i t y. Par tnership. Qual i t y.

DBCI’s Commercial Steel Curtain Roll-Up Door Solutions Include:

1900 Series (1950 Insulated)• 26-gauge Grade E galvanized

2000 Series (2250 Insulated) • 16-gauge galvanized steel drums with steel ball bearings• 26-gauge Grade E steel curtain

2500 Series (2750 Insulated)• Heavy duty• 10-gauge steel slide bolt lock• Width up to 18 feet

5000 Series (5250 Insulated)• Aluminum bottom bar with steel angle reinforcement• Wind certified up to 20’ wide

SE

RIE

S

DBCI’s 1900 Series is suitable for a number of light-

duty commercial uses. These doors are easy to

install and require low maintenance. You will enjoy

steady, quiet operation. The 1900 Series utilizes

9 ½” drums instead of the standard 12” drum.

This allows for less headroom when installing the

doors. DBCI’s commercial-grade steel curtain

roll-up doors are designed to meet and/or exceed

operational requirements for commercial doors

with little or no maintenance.

COMMERCIAL DOOR 1900 LIGHT-DUTY COMMERCIAL GRADE DOOR

DBCI | Toll Free: 800.542.0501 | E-mail: [email protected] | * For more detailed information and drawings: www.dbci.com

Cur tain

• 26-gauge galvanized, Grade E hard steel• Deep-ribbed corrugation• Maximum opening size of 12’ x 14’• Siliconized polyester WeatherX paint

over prime coat• 20 standard colors, special colors

available upon request• Wash coat over primer interior side• 30-year film integrity warranty, up to

25-year chalk and fade warranty• Flexible wear strips• NOTE: The 1900 is not rated for wind

loads. Please see the 2500 or 5000.

Bottom Bar

• 6063 – T6 aluminum extrusion• 2” x 1 ½” galvanized angles• Bulb astragal (Durometer 75)• Stainless steel nuts and bolts

Axle -Drum Assembly

• 1 5/16” O.D. steel axle, 14-gauge• 11-gauge on doors over 10’• Oil-tempered torsion springs• Utilizes 9 ½”, 18-gauge drums• Shielded steel ball bearings in drums• 26-gauge full top sheet

A .C .E . Guide System

• Advanced Curtain Engagement guide system

• Galvanized steel• Adjustable bolt on head stop• Polyethylene wear strip• Pre-punched for lock and attachment

fasteners

Hardware

• 13-gauge saddle clamps• 10-gauge slide locks; two per door• 16-gauge step plate; two per door• ¼” steel angle T-bracket

Opt ions

• Insulation 1950 Series• Chain hoist 4:1 reduction• Vision panels (17” x 5”)• Top draft stop• Hood• Steel mounting plates

Opening Height Headroom

• Up to 10’ is 17” of headroom• 10’ to 14’ is 19” of headroom

GUIDEDETAIL

DOORENGAGEMENT

INSULATEDDOOR DETAIL

GUIDEMOUNTING

INTERIORELEVATION

DOOR OPENING

OPENING WIDTH + 18"

HEADROOM

16 GA.

1.74

0.56

1.30

1.91

1.91

DOOR SHEETCURTIANWEAR STRIP

GUIDE STRIP

SELF DRILLINGSCREW


GUIDE STRIP

FOIL BACKED AIR-BUBBLE INSULATIONVINYL SIDE DRAFT STOP

SELF DRILLINGSCREW


GUIDE STRIP

SELF DRILLINGSCREWTAPCON XL


GUIDE STRIP

WOOD SCREW


GUIDE STRIP

STEEL MOUNTMASONRY MOUNT WOOD MOUNT

SERIES 1900

SERIES 1950







SE

RIE

S

COMMERCIAL DOOR 2000 LIGHT DUTY COMMERCIAL GRADE DOOR

The 2000 Series is the right choice for light-duty

applications requiring frequent usage such as

warehouses, freight terminals, car washes, machine

shops, auto body shops and much more. The

16-gauge, 12” drums allow for easy retraction. These

doors are low-maintenance, which is what every

owner wants in a quality door. DBCI’s commercial-

grade steel curtain roll-up doors are designed to

meet and/or exceed operational requirements for

commercial doors with little or no maintenance.

DBCI | Toll Free: 800.542.0501 | E-mail: [email protected] | * For more detailed information and drawings: www.dbci.com

GUIDEDETAIL

DOORENGAGEMENT


GUIDEMOUNTING

INTERIORELEVATION

Cur tain

• 26-gauge galvanized, Grade E hard steel• Deep-ribbed corrugation• Maximum opening size of 12’ x 18’• Flexible wear strips• NOTE: The 2000 is not rated for wind

loads. Please see the 2500 or 5000.

Bottom Bar

• 6063 – T6 aluminum extrusion• 2” x 1 ½” galvanized angles• Bulb astragal• Stainless steel nuts and bolts

Axle -Drum Assembly

• 1 5⁄16” O.D. steel axle, 14-gauge• 11-gauge axle on doors over 10’ wide• Utilizes 12”, 16-gauge drums• Shielded steel ball bearings in drums• Full top sheet

A.C .E . Guide System

• 16-gauge galvanized steel• Adjustable bolt on head stop• Polyethylene wear strip• Pre-punched for lock and attachment

fasteners

Hardware

• Saddle clamps with set fasteners• 10-gauge slide locks; 2 per door• 16-gauge step plate; 2 per door• ¼” steel angle T-bracket


• Doors up to 10’ have 20” of headroom• Doors 10’ to 14’ have 22” of headroom• Doors over 14’ have 24” of headroom

Options

• Insulated 2250 Series• 1900 Series – low overhead option• Chain hoist 4:1 reduction• Vision panels (17” x 5”)• Top draft stop• Hood• Steel mounting plates• Electric operator

SERIES 2000

SERIES 2250

DOOR OPENING

OPENING WIDTH + 18"

HEADROOM

16 GA.

1.74

0.56

1.30

1.91

1.91


GUIDE STRIP

SELF DRILLINGSCREW


GUIDE STRIP


SELF DRILLINGSCREW


GUIDE STRIP

SELF DRILLINGSCREWTAPCON XL


GUIDE STRIP

WOOD SCREW


GUIDE STRIP

STEEL MOUNTMASONRY MOUNT WOOD MOUNT







SE

RIE

S


COMMERCIAL DOOR 2500 HEAVY DUTY COMMERCIAL GRADE DOOR

The 2500 Series is DBCI’s heavy duty steel curtain

roll-up door with tremendous versatility and

unmatched quality. The 2500 Series has deep

engagement guides creating greater durability

and stronger, longer lasting performance. DBCI’s

commercial-grade steel curtain roll-up doors are

designed to meet and/or exceed operational

requirements for commercial doors with little or

no maintenance.

INTERIORELEVATION

GUIDEMOUNTING

GUIDEDETAIL

DOORENGAGEMENT


DBCI | Toll Free: 800.542.0501 | E-mail: [email protected] | Website: www.dbci.com

Cur ta in

• 26-gauge galvanized, Grade E hard steel• Deep-ribbed corrugation• Maximum opening size of 18’ x 18’• Flexible wear strips• NOTE: The 2500 Series are wind rated up

to 12’0” wide and approximately 90 MPH. The MPH rating increases as the door width decreases. For test results on doors up to 12’0” wide, please contact DBCI Sales at 800.542.0501.

Bottom Bar


Axle -Drum Assembly

• 1 5⁄16” O.D. steel axle, 14-gauge• 11-gauge axle on doors over 10’ wide• Utilizes 12”, 16-gauge drums• Shielded steel ball bearings in drums• Full top sheet• Oil tempered torsion springs

A.C.E . Guide System • 14-gauge galvanized steel• Adjustable bolt on head stop• Polyethylene wear strip• Pre-punched for lock and attachment

fasteners

Hardware

• Saddle clamps with set fasteners• 10-gauge slide locks; 2 per door• 16-gauge step plate; 2 per door• ¼” steel welded angle T-bracket


• Doors up to 10’ have 20” of headroom• Doors 10’ to 14’ have 22” of headroom• Doors over 14’ have 24” of headroom

Options

• Insulated 2750 Series• Chain hoist 4:1 reduction• Vision panels (17” x 5”)• Top draft stop• Hood• Steel mounting plates• Electric operator• Low headroom 2400 Series

DOOR OPENING

OPENING WIDTH + 18"

HEADROOM

14 GA.

2.97

3.16

1.94

0.57

1.30

SERIES 2500


GUIDE STRIP

SELF DRILLINGSCREW

SERIES 2750


GUIDE STRIP


SELF DRILLINGSCREW

MASONRY MOUNT


GUIDE STRIP

TAPCON XL

STEEL MOUNT


GUIDE STRIP

SELF DRILLINGSCREW

WOOD MOUNT


GUIDE STRIP

WOOD SCREW


SE

RIE

S





COMMERCIAL DOOR 5000 WIND CERTIFIED DOOR

When it comes to withstanding Mother Nature’s

wrath, DBCI has the doors you need. Our 5000

Series utilizes deep engagement guides and side

curtain windlocks that are designed to maintain

the operation integrity of the door and meet

most state and local building codes, especially

in coastal regions and Florida. The 5000 Series is

made of 26-gauge, Grade E hard steel to ensure

quality and dependability. DBCI’s commercial-

grade steel curtain roll-up doors are designed to

meet and/or exceed operational requirements for

commercial doors with little or no maintenance.


Cur tain

• 26-gauge galvanized, Grade E hard steel• Deep-ribbed corrugation with three-rivet

windlock attachment• Maximum opening size of 20’ x 16’• Flexible wear strips• NOTE: The 5000 Series are wind rated up

to 20’0” wide and approximately 120 MPH. The MPH rating increases as the door width decreases. For test results on doors up to 20’0” wide, please contact DBCI Sales at 800.542.0501.

Approximate* MPH Cer t i f icat ion

• 10’ wide = 150 mph• 12’ wide = 150 mph• 14’ wide = 146 mph• 16’ wide = 140 mph

*For test results on doors up to 20’ wide, please contact DBCI Commercial Sales at 800.542.0501.

Bottom Bar


Axle -Drum Assembly

• 1 5⁄16” O.D. steel axle, 14-gauge• 11-gauge axle on doors over 10’ wide• Utilizes 12”, 16-gauge drums• Shielded steel ball bearings in drums• Full top sheet• Oil tempered torsion springs

A.C.E . Guide System

• 12-gauge galvanized steel• 12-gauge wind lock bar• Adjustable bolt on head stop• Polyethylene wear strip• Pre-punched for lock and attachment fasteners

Hardware

• Saddle clamps with set fasteners• 10-gauge slide locks; 2 per door• 16-gauge step plate; 2 per door• ¼” steel angle T-bracket


• Doors up to 10’ require 20” of headroom• Doors 10’ to 14’ require 22” of headroom• Doors over 14’ require 24” of headroom

Options

• Chain hoist 8:1 reduction• Header seal• Hood• Steel mounting plates• Electric operator

GUIDEDETAIL

GUIDEMOUNTING

DOORENGAGEMENT

INTERIORELEVATION

MASONRY MOUNT STEEL MOUNT

DBCI | Toll Free: 800.542.0501 | E-mail: [email protected] | Website: www.dbci.com

CURTAIN

HEAD STOP(REMOVABLE)SYMMETRICAL

BOTTOM BARASSEMBLY

END

OF

AX

LE

END

OF

AX

LE

WALL OPENING WIDTH

6-1/2"

10-1/2"10 1/2"

TOP BARREL ASSEMBLY

GUIDE WOOD/STEEL JAMBS

UNIVERSAL GUIDE

CONCRETE/MASONRY JAMBS

4"GRADE

BRACKET ATTACHMENT:CONCRETE/MASONRY: SLEEVE ANCHOR, 3/8" X 1-7/8" LG.WOOD: LAG SCREW, 3/8-7 X 3" LG.STEEL: HEX BOLT, GR.5, 3/8-24 X 1-1/4" LG.

(*) FOR PUSH-UP OPERATION 6-1/2" FOR HAND CHAIN OR ELECTRIC OPERATION 10"NOTE: LEFT SIDE DRIVE SHOWN

TYPICAL PANEL

1/2"

1"MIN.

WIND LOCK AT EVERYOTHER CORRUGATION

GUIDE

3/8" SLIP FOR DOOR WIDTHLESS THAN OR EQUAL TO12'-10"; 1/2" SLIP FOR DOORWITH GREATER THAN 12'-10"AND LESS THAN 16'-10"

TYPICAL PANEL


GUIDE

EXISTINGSTEEL JAMB

TYPICAL PANEL


GUIDE

EXISTING STEEL JAMB1/4" MIN. THICKNESS

Fueled by constant changes in local and national building codes, as well as increasing insurance costs, doors with validated wind certification can dramatically reduce maintenance and replacement costs and minimize downtime. DBCI’s wind-certified doors are designed to meet stringent building codes in coastal regions and Florida.

*Also avai lable with insulat ion (5250 Ser ies)

commercial door 1900 light-duty commercial grade … · 2018. 10. 11. · dbci’s commercial steel...

Documents