concrete equipment catalogue

Concrete & Grout Mixer Pump Equipment

Concrete Pumps 2

Grout Mixers & Pumps 18

Gunite Pumps 44

Dust Extractors 51

Shotcrete Machines 55

Pan & Paddle Mixers 65

Parts, Accessories & Maintenance 71

Concrete Pumps

Antec’s quality range of concrete pumps can pump and spray most pre-blended cementitious construction material for a huge range of applications including slope stabilisation, foundations, pressure grouting, refractory and more. FEATURES: • Handle a range of materials from harsh pea gravel mixes through to big rock

concrete • Wide range of horsepower, pressure and volume combinations • Super heavy duty steel frames • Weatherproof engines and frames built to thrive in extreme conditions • Smart, simple designs for easy operation and maintenance • Industry-leading safety features to protect people and machinery • Customisation for specific applications and worksites available

A Series “Rockmaster” Pumps A30 / A30HP / A40HP Trailer Mounted Concrete Pumps

• The Rockmaster delivers outstanding long term value for money by virtue of its reliability, toughness, ease of use, durability and pumping power.

• The Rockmaster is powered by a 82hp (61 kW) continuous duty diesel engine. • This best-in-class power is the basis for the pump’s versatility. • It can be used to pump rough concrete mixes as well as shotcrete (A40HP is recommended for higher

pressure applications). • The Rockmaster features an “Open-Loop” hydraulic system, a large fuel tank, and REED’s Can-Bus Solid

State Cycle Control.

STANDARD FEATURES • Turbo Series Super Duty Powerful 82 hp (61kW) diesel engine (continuous duty) • Variable Displacement Piston Hydraulic Pump (A30HP and A40HP models) • Gear Pump (A30 model) • Heavy-duty “S” Valve • Lightweight • REED Can-Bus Solid State Electric System • Chromed concrete cylinders for long service life • Easy to change Piston Cups • High-strength frame design • Only 4 hydraulic hose groups (8 hoses total) • Adjustable tongue jack • Fuel Filters (pre-filter with water separator and spin off primary filter)

APPLICATIONS • Big Rock • Grout • Pea Gravel • Shotcrete • Slope Stabilisation • Ponds & Spas • Slabs • Rockscaping • Mines • Backfill • Foundations • Pressure Grouting

ADDITIONAL FEATURES •Reversibility at any point in the stroke •Variable volume output •Weatherproof NEMA 4 control panel •High capacity hydraulic oil cooler •Highway rated axle •Electric brakes •Fenders and flush-mounted tail-lights •Adjustable pintle hitch •Hopper grate •Safety emergency stop function •Steel pistons with urethane cups •Hard chromed concrete cylinders •Hour meter •Splined shaft on “S” valve •Dual hydraulic circuit •Highest standard horsepower and concrete pressure in class

OPTIONAL FEATURES • Radio remote control • 7-function hardwire remote control

(on/off / reverse / e-stop / horn reset / RMP control / stroke change)

• Hopper Agitator (A40HP only) • Chrome wheels • Hydraulic surge brakes 2 50/16” Ball

Hitch screw-type outriggers (manual, adjustable)

• U.S. Tool Kit (for international customers)

• Emergency Stroke Kit

MODEL A30 A30HP A40HP

Concrete Output yd3/hr m3/hr

30 23

30 23

40 31

Concrete Pressure psi Bar

903 62

903 62

1172 81

Horizontal Pumping Pressure

ft m

900* 274*

900* 274*

975* 297*

Vertical Pumping Pressure

ft m

350* 107*

350* 107*

400* 122*

Perkins Diesel Engine hp kW

82 61

82 61

82 61

Main Hydraulic Pump Gear Pump

71cc Variable Displacement

100cc Variable Displacement

Concrete Cylinder Diameter

in mm

5” 127

5” 127

6” 152

Stroke Length in mm

30” 762

30” 762

30” 762

Maximum Aggregate Size

in mm

1” 25

1” 25

1.5” 38

Hopper Capacity ft3

litres 10 283

10 283

10 283

Hopper Height In mm

40 1016

40 1016

40 1016

Hydraulic Oil Capacity gal litres

40 151

40 151

40 151

Fuel Capacity gal litres

29 110

29 110

29 29

Outlet Size in mm

5 127

5 127

5 127

Dimensions In mm

L 160 4064

W 61 1549

H 64 1626

Weight lbs kg

4600 2087

4600 2087

4760 2159

* Theoretical distances and performance shown above are estimated using standard industry methods. Actual performance will vary depending on the concrete pump (concrete pressure, horsepower), material (mix design, slump, local sand and rock characteristics) and delivery system (pipeline diameter, type (steel or hose) and reductions / bends. Maximum output, pressure, and distance cannot be reached simultaneously. Specifications subject to change without prior notice.

A Series “Rockmaster” Pumps A30 / A30HP / A40HP Trailer Mounted Concrete Pumps

B Series Trailer Mounted Concrete Pumps B20/B20HP/B50/B50HP/B60/B70A

• These rugged pumps feature “Open Loop” hydraulic systems and variable displacement hydraulic pumps. • All B Series Pumps now feature Cummins Diesel Engines that are more powerful (more torque), quieter

and more efficient (lower RPMs) and EPA Tier 3 approval – 110 or 130hp (82 or 97kW). • The simple design of the B Series pumps makes them easy to trouble-shoot and service. • A variety of output and pressure ranges makes the B Series top performers for any application.

STANDARD FEATURES • REED PLC (Programmable Logic Controller)

• Allows for self diagnosis on the LCD, simple adjustments, and future enhancements

• Variable-volume and R.P.M. control at remote control box

• Adjustable shifting force valve

• Heavy-duty “S” valve

• Chromed concrete cylinders for long service life

• High-strength frame design (sturdiest frame in industry)

• Integrated toolbox

• Highest commonality of hydraulic hoses

APPLICATIONS • Shotcrete • Concrete Pumping • Pressure Grouting • Foundations • Slope Stabilisation • Pools • Refractory Materials • Slabs • Rockscaping • Mines • Backfill • Flowable Fill

B Series Trailer Mounted Concrete Pumps B20/B20HP/B50/B50HP/B60/B70A

ADDITIONAL FEATURES •Super heavy-duty steel frame •Weatherproof NEMA 4 control panel •Reversibility at any point in the stroke •High capacity hydraulic oil cooler •Fully-variable volume output •9000lb (4083kg) highway rated axle (all but B20 Model) •Electric brakes •Fenders and flush-mounted tail-lights •2 heavy-duty outriggers •Adjustable pintle hitch •Hopper grate •Automatic pressure release at shutdown •Forged steel pistons with urethane cups •Hard chromed concrete cylinders •Hour meter / tachometer •Emergency stop button •5-function cable remote control •Dual hydraulic circuit •Highest standard concrete pressure in class •Wide stance •Harsh-Mix Hopper (B70 only)

OPTIONAL FEATURES •Radio remote control (On/Off) •Reverse/E-stop/Horn reset/Engine RPM) •Hydraulic outriggers •Hopper agitator •Dual shift cylinders (Standard on B70) •Vibrator for hopper screen •Aluminium wheels •Hydraulic surge brakes •Chemical additive pump •Stroke counter •Skid mounting •Electric motor •Lifting-eye kit •“Emergency” stroke change kit •Hopper extension (increase cap. To 16cf) •Carbide Wear Parts •Hydraulically driven water washout pump

MODEL B20 B20

HP

B50 B50

HP

B60 B70


20 15

20 15

50 38

50 38

60 46

70 54

Concrete Pressure

psi Bar

1664 115

2113 145

1361 94

1361 94

1174 81

1000 69


ft m

1650*

503*

2200*

670*

1200*

365*

1200* 365

950*

290*

750*

228*


ft m

700*

213*

875*

267*

450*

137*

450*

137*

375*

114*

300*

91*

Cummins Diesel Engine

hp kW

110 82

110 82

110 82

130 97

110 82

130 97

Main Hydraulic Pump

cc/rev 71 100 140 140 140 140


in mm

4” 102

4” 102

6” 152

6” 152

6” 152

7” 178

Stroke Length in mm

36” 914

36” 914

36” 914

36” 914

36” 914

36” 914


in mm

¾ “ 19

¾ “ 19

1 ½” 38

1 ½” 38

1 ½” 38

1 ½” 38

Hopper Capacity ft3

litres 10 283

10 283

12 340

12 340

12 340

14*

400*

Hopper Height In mm

42 1067

42 1067

42 1067

42 1067

42 1067

45*

1143*

Hydraulic Oil Capacity

gal litres

52 197

52 197

52 197

52 197

52 197

52 197


24 91

24 91

24 91

24 91

24 91

24 91

Outlet Size in mm

4 102

4 102

5 127

5 127

5 127

5 127

Dimensions In mm

L 170 4318

W 74 1879

H 83 2108

Weight lbs kg

5980 2718

5980 2718

6580 2991

6580 2991

6740 3063

6980 3173


B50 Concrete Pump on Tracks

Antec ‘s customised Reed B50 Concrete Pump with tracks is ideal for use on both rough and large sites. The B50 Concrete Pump was fitted with tracks and electrics that enable it to be self-propelled. The advantage is that the pump can drag the concrete hoses with it, removing labour required and increasing productivity. The heavy duty tracks enable the pump to traverse rough terrain when relocating from part of the site to the other. Easy to maneuver, the B50 on tracks can turn around on its own length with no effort and can walk from one location to another with the piling rig, whilst still hooked up to the rig. Combined with the high strength frame standard on all Reed concrete pumps, the customised Reed B50 Concrete Pump on tracks provides the ideal solution for construction and maintenance works. The B50 on tracks was developed specifically for MGI Piling.

ADDITIONAL FEATURES • Super heavy-duty steel frame • Weatherproof NEMA 4 control panel • Reversibility at any point in the stroke • High capacity hydraulic oil cooler • Fully-variable volume output • 9000lb (4083kg) highway rated axle • Electric brakes • Fenders and flush-mounted tail-lights • 2 heavy-duty outriggers • Adjustable pintle hitch • Hopper grate • Automatic pressure release at shutdown • Forged steel pistons with urethane cups • Hard chromed concrete cylinders • Hour meter / tachometer • Emergency stop button • 5-function cable remote control • Dual hydraulic circuit • Highest standard concrete pressure in class • Wide stance

OPTIONAL FEATURES • Radio remote control (On/Off) • Reverse/E-stop/Horn reset/Engine RPM) • Hydraulic outriggers • Hopper agitator • Dual shift cylinders (Standard on B70) • Vibrator for hopper screen • Aluminium wheels • Hydraulic surge brakes • Chemical additive pump • Stroke counter • Skid mounting • Electric motor • Lifting-eye kit • “Emergency” stroke change kit • Hopper extension (increase cap. To 16cf) • Carbide Wear Parts • Hydraulically driven water washout pump

MODEL B50


50 38


1361 94

Horizontal Pumping Pressure ft m

1200*

365*

Vertical Pumping Pressure ft m

450*

137*

Cummins Diesel Engine hp kW

110 82

Main Hydraulic Pump cc/rev 140

Concrete Cylinder Diameter in mm

6” 152

Stroke Length in mm

36” 914

Maximum Aggregate Size in mm

1 ½” 38

Hopper Capacity ft3

litres 12 340

Hopper Height In mm

42 1067


52 197


24 91

Outlet Size in mm

5 127

Dimensions In mm

H 83 2108

Weight lbs kg

6580 2991


B50 Concrete Pump on Tracks

B50 Hybrid Concrete Mixer & Pump Hydraulic & air operated pump for mixing, pumping & shotcreting underground

• The B50 Hybrid is a combined mixing and concrete pumping unit that has been specifically designed for use in underground applications.

• Traditional concreting in underground areas required the use of a wet pre-mix material however issues with quality and product use by dates can affect the finished result.

• The design of the B50 Hybrid pump ensures the quality control of material with wet application using bulk dry material that can be delivered, stored and used as required.

• The result is low dust due to wet application and improved quality and reliability.

• The B50 Hybrid uses hydraulic power from a coal tram or Eimco unit to power the mixer and pump (minimum hydraulic power required 180 litres / min at 2,000 psi).

• Offers increased productivity of 5 tonne per hour vs. 0.8 tonne per hour for dry shotcrete, thereby reducing labour costs and increasing re-entry to mine areas.

• Hydraulic power means no electrical issues for environments where intrinsically safe power is required.

APPLICATIONS • Shotcrete

• Concrete Pumping

• Pressure Grouting

• Foundations

• Slope Stabilisation

• Slabs

• Rockscaping

• Mines

• Backfill

• Flowable Fill

FEATURES PUMP: •Super heavy-duty steel frame •Variable-volume and RPM control at remote control box •Adjustable shifting force valve •Heavy-duty “S” valve •Chromed concrete cylinders for long service life •Reversibility at any point in the stroke •Fully-variable volume output •Hopper grate •Forged steel pistons with urethane cups •Hard chromed concrete cylinders •Emergency stop button x 2 MIXER: •Heavy duty construction •Replaceable wear resistant bowl liners •Manual bag breaker (x2) and inspection and cleanout access •Manual discharge •Single section platform •Ladder retracts and locks for transportation •Six paddle mixing configuration •All blades, wearing surfaces & bowl liner made from Bisalloy material

OPTIONAL FEATURES •Batching water tank •Air additive dosing pump for shotcreting

MODEL B50

HYBRID

COMPLETE UNIT

Mix & Spray Output

m3/hr 3.5

Pump Only Output

m3/hr 30

Outlet Size in mm

5 127

Dimensions Complete Unit

mm L 4483 W 1490 H 1730

Weight kg 4500

PUMP CELL


in Mm

6” 152

Stroke Length in mm

36” 914

Hopper Capacity ft3

litres 12

340

MIXER UNIT

Bowl Volume m3 0.42

Mix Capacity Kg 500

Mixing Speed RPM 36-40

Hydraulic Motor kW 22


in mm

1 ½” 38

Dimensions Bowl Only

mm Ø 1500 H 400

B50 Hybrid Concrete Mixer & Pump Hydraulic & air operated pump for mixing, pumping & shotcreting underground

ADVANTAGES •Limited number of moving & wear parts = reduced maintenance •Hydraulic power results in a constant (even) power source •Easy operation – simply add water at the mixing stage and accelerator (if required) at the nozzle (note: for shotcreting a low air supply of 100psi is required) •Safe, reliable and easy to operate •Option to mix and pump dry batched material OR pump only with pre-mixed wet cement

* Theoretical distances and performance shown above are estimated using standard industry methods. Actual performance will vary depending on the concrete pump (concrete pressure, horsepower), material (mix design, slump, local sand and rock characteristics) and delivery system (pipeline diameter, type (steel or hose) and reductions / bends. Maximum output, pressure, and distance cannot be reached simultaneously. Specifications subject to change without prior notice. Patent Pending

• The extremely compact size of the Mine 30 pump makes it ideal for underground applications or any application with limited space.

• The Mine 30 is suitable for cross mounting on a truck or other carrier. Fork channels on the side and end also come standard.

• The Mine 30 can be powered by an electric, diesel, or air motor. • The simple design of the Mine 30 makes it easy to trouble-shoot and service. It provides strong

performance, extreme dependability and long life of all wear parts.

STANDARD FEATURES

• Heavy-duty “S” valve

• “Open-loop” hydraulic system and a variable displacement hydraulic pump

• Adjustable shifting force valve

• Chromed concrete cylinders for long service life

• High-strength frame design (sturdiest frame in the industry)

• Highest commonality of hydraulic hoses.

APPLICATIONS

• Shotcrete

• Concrete Pumping

• Grouting

• Backfill

• Mine & Tunnel Support

• Flowable fill

• Specialty Materials

Mine 30 Pump Compact Wet-Process Shotcrete / Concrete / Grout Pump

OPTIONAL FEATURES • Radio remote control (on/off / reverse / e-stop /

horn reset / engine RPM) • Hopper Agitator • Dual shift cylinders • Vibrator for hopper screen • Chemical additive pump • Stroke counter • Lifting-eyes • Hydraulically driven water washout pump

MODEL Mine 30


30 23


1172 81

Motor / Engine hp kW

50 37

Main Hydraulic Pump cc/rec 100


in mm

6” 152

Stroke Length in mm

19” 495

Maximum Aggregate Size in mm

1.5” 38

Hopper Capacity (standard rugged hopper)

ft3

litres 10

283

Hopper Height Harsh Mix Hopper

In mm

40 1015


40 150

Outlet Size in mm

5 127

Weight (approximately) lbs kg

4650 2110

Mine 30 Pump Compact Wet-Process Shotcrete / Concrete / Grout Pump

Note: Specifications are subject to change without prior notice. Actual performance will vary depending on the concrete pump (concrete pressure, horsepower), material (mix design, slump, local sand and rock characteristics) and delivery system (pipeline diameter, type (steel or hose) and reductions / bends. Maximum output, pressure and distance cannot be reached simultaneously.

ADDITIONAL FEATURES •Weatherproof NEMA 4 control panel •Reversibility at any point in the stroke •High capacity hydraulic oil cooler •Fully-variable volume output •Automatic pressure release at shutdown •Forged steel pistons with urethane cups •Hard chromed concrete cylinders •Hour meter / tachometer •Emergency stop button •5-function cable remote control •Dual hydraulic circuit

Mine Configured & Compliant Skid Mounted Concrete Pump

• The Rockmaster delivers outstanding long term value for money by virtue of its reliability, toughness, ease of use, durability and pumping power.

• Customised configuration for underground mining make these pumps the first choice in tough conditions.

PUMP STANDARD FEATURES •Three Series and 14 models to choose from

•Various outputs from 15m3/hr to 69m3/hr

•Various options for the concrete pump: remote, agitator, auto-lubricator, vibrator, stroke counter, hopper extension, electric motor

•Diesel Engines are powerful, quiet, efficient, and EPA Tier 3 approved

•Common Hydraulic Hoses Field - Experienced Engineers designed the layout so you carry less.

•Adjustable Shifting- Force Valve lets you customize S-Tube force for a wide variety of pumping challenges

•Integrated Locking Toolbox is conveniently located for easy access

•REED “1•2•3 Warranty” covers parts, structure and the controller

•REED P.L.C. (Programmable Logic Controller) allows for self diagnosis on the LCD, simple adjustments, and future enhancements

•Highest Concrete Pressure (up to 2113 p.s.i depending on model)

•Low Hopper Height (43”) for easy fill from old-style mixer trucks

•Reverse function is standard on cable and radio remote

SAFETY FEATURES •All fuel lines are stainless steel braded hoses

•Exhaust lagging fitted & extra exhaust shielding over the lagging on the muffler

•Radiator Cooling Fan Guard Cover

•Level type radiator cap

•Steel fuel filter and pump

•Engine Management warning

•Starter Motor Isolator & Lock Out

•OEM Control Panel

•OEM Remote Control (mounted in cradle)

•Remote Charge Lead ( 12v )

•Battery Isolator Switch & Lock Out

•Diverter Box actuator ram guarding

•Main Battery Fuse and 350A Anderson Plug & Cover

•All electrical wiring are covered with split type cable coating

•Safety Decal at all key areas

STRUCTURAL FEATURES •Modular steel structure designed to protect all sides

of the pump

•4 lifting lugs with a capacity of x

•Skid mounted with tyne slots for large forklifts

•Structural engineering certificate is available

•Lockable cage doors on either side of the pump

•Document holder

FIRE PROTECTION FEATURES •9kg DP Fire Extinguisher

•9kg Foam Extinguisher

•The fire protection system associated with Reed equipment is in accordance with the intent of the following documents:

• Fire Risk Assessment

• PEFS Design, Installation & Commissioning Manual V2.1

• BHP Fatal Risk Protocols

SYSTEM DESIGN SPECIFICATION

The system design has been based on the results of the Fire Risk Assessment and the latest version of CFS’s listed PEFS Design, Installation and Commissioning Manual

Operating Mode Loss of Pressure or Rise of Pressure

System Function Fire alarm system with automatically operated suppression system and engine shut down

Protection Area(s) Engine

Detection Type(s) Burn Tube

Activation Method(s) Automatic & Manual

Activation Points Manual Actuation in the cabin & Manual Actuation mounted as near as practicable to the battery isolator

Discharge Time Min 70 seconds

Shutdown Time 0

Shutdown Extension Time 0

Agent Discharge Delay Time N/A

Mine Configured & Compliant Skid Mounted Concrete Pump

MECHANICAL SYSTEM

C23 Cylinder Bracket

C23 LOP Cylinder Assembly

Manual Actuator Remote

BM17 Nozzles

BM16 Nozzles

Lot Pneumatic system – hose, fittings, brackets & fasteners

Lot Discharge system – Hose, stainless steel tube, fittings, brackets & fasteners

System operation & warning labels

ELECTRICAL SYSTEM DESCRIPTION

FSM Shut down panel with no battery pack power supply

Lot of cable, connectors and fasteners

Connection of the control system

MISCELLANEOUS DELIVERABLES

Installation labour (see exclusions)

Owners manual

9kg DCP Extinguisher & bracket (supply only)

9lt AFFF Extinguisher & bracket (supply only)

SITE COMMISSIONING

Full functional test of alarm, detection and release devices

Discharge test

Commissioning report

C Series Trailer Mounted Concrete Pumps 50S / C50SS / C70S / C70SS / C90S

• REED C series pumps feature Rexroth “Closed-Loop” hydraulic systems, twin axles and twin-shift cylinders. These high-performance pumps excel even under the most extreme conditions.

• REED is the first trailer pump manufacturer to bring this top level Boom Pump technology to trainer pumps.

• The rugged, powerful C Series pumps are designed to withstand the punishment inherent to heavy construction environments.

• Superior engineering, premium technology, top quality components and pride in workmanship make C Series pumps the most reliable pumps on the market.

STANDARD FEATURES • Rexroth Closed-loop overcentre hydraulic system • Powerful Cummins Diesel Engine (more torque) • Quieter and more efficient (lower RPM’s). EPA Tier 3 approval. • REED PLC (Programmable Logic Controller) • Allows for self diagnosis on the LCD, simple adjustments and future enhancements. • Variable-volume and R.P.M. control at remote control box • Carbide Wear Parts • Hydraulic Outriggers • Super heavy-duty frame (sturdiest frame on market) • Twin axle trailer 2x7000lb (2x3182kg) • 3” splined shaft on heavy duty “S” tube • 42” stroke length • Special high-pressure reinforced hopper

APPLICATIONS • Big Rock • Grout • Pea Gravel • Shotcrete • Slope Stabilisation • Ponds & Spas • Slabs • Rockscaping • Mines • Backfill • Foundations • Pressure Grouting

ADDITIONAL FEATURES •Adjustable shifting force valve •Stainless steel hopper splash guard •Hard chromed concrete cylinders •Large fuel tank capacity with gauge •Weatherproof NEMA 4 control panel •High capacity hydraulic oil cooler •Remote control with 15m cable

a. On / Off b. Forward / Reverse c. Stroke Change (S-tube jog) d. Engine RPM control e. Hydraulic

•Pump volume control •Hour meter / tachometer •Reversibility at any point in the stroke •Safety emergency stop function •3” diameter splined shaft on “S” valve •Highest commonality of hydraulic hoses •Hopper grate

OPTIONAL FEATURES • Radio remote control • Hydraulically driven water washout

pump • Vibrator for hopper screen • Chemical additive pump • Stroke counter • Skid mounting • Lifting eyes • “Murphy” switch for engine • Electric motor instead of diesel • Surge breaks


C Series Trailer Mounted Concrete Pumps 50S / C50SS / C70S / C70SS / C90S

MODEL C50

S

C50

SS

C70

S

C70

SS

C90

S

H.V.

C90

S

H.P.


50 38

54 41

70 54

74 556

90 69

74 56

Concrete Pressure

psi Bar

1640 114

2000 138

1205 84

1469 102

896 62

1469 102


ft m

1425*

434*

2000*

610*

1000*

305*

1350* 411

1000*

305*

1350*

411*


ft m

575*

175*

800*

244*

425*

130*

550*

168*

550*

168*

425*

130*

Cummins Diesel Engine

hp kW

160 119

220 164

160 119

220 164

220 164


in mm

6” 152

6” 152

7” 175

7” 175

7” 175

Stroke Length in mm

42” 1067

42” 1067

42” 1067

42” 1067

42” 1067


in mm

1 ½“ 38

1 ½“ 38

1 ½” 38

1 ½” 38

1 ½” 38

Hopper Capacity Standard

ft3

litres 12 340

12 340

N/A N/A N/A

Hopper Capacity Harsh Mix

ft3

litres N/A N/A 14.5

410 14.5 410

14.5 410

Hopper Height Standard

in mm

44” 1118

44” 1118

N/A N/A N/A

Hopper Height Harsh Mix

in mm

N/A N/A 47” 1194

47” 1194

47” 1194

Hydraulic Oil Capacity

gal Litres

60 227

60 227

60 227

60 227

60 227


39 148

39 148

39 148

39 148

39 148

Outlet Size in mm

5” 127

5” 127

5” 127

5” 127

5” 127

Dimensions in mm

L 184” 4674

W 71” 1803

H 83 2108

Weight (approx.) with oil & fuel

lbs kg

8260 3755

8260 3755

8600 3909

8600 3909

8750 3977

Grout Mixers & Pumps

Antec are the exclusive distributors of the ChemGrout and Clever & Co Grouting equipment ranges.

ChemGrout FEATURES: • Integrated mixing and pumping • Colloidal and paddle type mixers

available • Variety of grout pumps including

piston, plunger and progressing cavity equipment

• Engineered to be user friendly and trouble free

• Variety of power options including air, hydraulic, electric, electric / hydraulic, gasoline and diesel / hydraulic

Clever & Co FEATURES: • Developed for universal applications • Especially designed for injection and

grouting works, drill hole or backfilling jobs and processing of wet spraying mortars

• Robust for use in underground situations, tunnel construction or civil engineering

• High performance pumps are both variable and economical

• Conveying capability of up to 90 litres per minute and a conveying range of 100m or more

Grout Mixer & Pump • The Clever & Co grout mixer has been developed for universal applications. • Especially designed for injection and grouting works, drill hole-or backfilling jobs and processing of wet

spraying mortars. • Long lasting and robust for use in underground, tunnel construction or civil engineering.

MODEL CL02 CL06

Worm Pump Type MP2-MP18 MP2-MP18

Grain Size l/min 0-8 0-8

Conveying capability (depending on worm pump used)

m 3.3-90 5-90

Conveying range bar 100 and more 100 and more

Pump pressure bar Max. 50 Max. 50

Dimension L x W x H 1,000 x 650 x 750 1,000 x 650 x 865

Weight kg Ca. 100 Ca. 210

Gear kW, u/min 3.0/150 or 5.5/190 5.5 / 190

Operating Voltage V, Hz, A 400/50 400/ 50

Fusing A 16/32 32

Type CL02 •High performance mortar pump used for the pumping and spraying of ready-mixed, machine customised cement mortars. •The mortar pump gets filled directly, via a continuous mixer or a compulsory mixer. •The mortar gets sucked up from the hopper by worm drive and will be red via the patented worm pump (up to 150m)

Type CL06 •Continuously working mixing pump which permits the problem free mixing and pumping of dry-mixture mortar at the same time. •The drive is provided by a single main motor supplying the material from the hopper to the mixing chamber. •The dry-mixture mortar gets continuously mixed with the water in the mixing section and will be transported to the downstream worm pump. An optional mixing chamber extension ensures that special mixtures can also be homogenously mixed at any time.

ChemGrout CG-050 Air Powered Compact Grouter • Lightweight aluminium construction offers portability for confined, hard to reach jobs • Ideal for efficient grouting of smaller applications • Designed for pumping grout mixes, high viscosity slurries and premixed grouts • Delivers up to 5 gpm with pressures to 225 psi (400 psi hydraulic) • Utilises a 19 litre holding hopper and 2” piston pump • Engineered for minimal maintenance with only three wetted and five working parts • Quick disconnect couplings allow for rapid disassembly in just seconds for easy maintenance and

clean-up. • The safe, compressed air drive is especially suited for mines, tunnels and remote sites where fuel

fumes are dangerous and electricity is unavailable. • One-man operation saves both time and money.

CG-050 Air Hydraulic

Pump 2” piston 2” piston

Output 5 gpm (19 lpm) 5 gpm (19 lpm)

Pressure 225 psi (16 bar) 400 psi (28 bar)

Weight 25kg 48kg

Requires 15 cfm, 100 psi 5 gpm, 1000 psi

Size 111.76cm x 112.5cm x 60.96cm (L x W x H)

APPLICATIONS

• Door & window frames • Void filling • Slab raising • Pavement dowel bars • Piling encasements • Machine base & joint

grouting • Waterproofing • Piling encasements • Precast tunnel joints • Concrete floors / roofs

ChemGrout CG-050M Manual Hand Pump • Heavy duty manual hand pump is an easy to use, skid mounted hand pump designed for smaller jobs

using high viscosity slurries and most pre-packaged grouts. • Rugged, lightweight aluminium construction offers mobility in areas where no air or electric power

sources are available • Features a large 5 gallon holding hopper and durable 2” piston pump that produces discharge head

exceeding 45.7m (ideal for vertical lifting) • The manually powered, positive displacement piston pump disassembles in minutes without tools for

simple cleaning and maintenance

CG-050M Manual Hand Pump

Pump 2” piston

Output 2-3 gpm (7-11 lpm)

Pressure 200 psi (14 bar)

Weight 24kg


APPLICATIONS



ChemGrout CG-550P Air Powered Compact Grouter • Versatile unit is a complete grouting system that provides continuous operation by combining a high

efficiency paddle mixer and the field proven CG-050 2” positive displacement piston pump • Air or hydraulically powered, the skid mounted 550P features a 128 litre mixing tank equipped with

baffles, bag breakers and a variable speed high-efficiency paddle that insures rapid and thorough mixing

• Once mixed, material is transferred into a 19 litre holding hopper through a slide gate specially designed to handle the most difficult materials.

• Single operation required to control both the mixer and pump, increasing productivity. • Rugged steel framed system stands up to the toughest job site conditions.

APPLICATIONS



CG-550P Air Hydraulic

Pump 2” piston 2” piston

Paddle Mixer 128 L 128 L

Output 5 gpm (19 lpm) 5 gpm (19 lpm)

Pressure 225 psi (16 bar) 400 psi (28 bar)

Weight 136kg 186kg

Power Required 85 cfm, 100 psi 2 supplies ea/5gpm, 1500 psi


ChemGrout Quattro Continuous Mixing Grouting System • Narrow enough to easily roll through doorways, the Quattro is ideal for both spray and pour

applications • Self contained with built in air compressor and water pump • Delivers a non-stop, steady material flow for a variety of spray and pour applications • Dry materials are conveyed from the hopper via a metering star wheel into the mixing chamber. • Precision water controls ensure that the proper amount of water is added • Single operator required • Superior material consistency and flow rates of up to 13 gpm • Control boxes are hermetically sealed to protect them from dust and water • Automatic shutoff systems, remote control, extra rotor / stator, grout / air hoses, spray wand, hopper

cover and tool kit are standard

APPLICATIONS

• Fireproofing

• Stucco

• Plaster

• Self leveling underlayments

• Mortar sprayer

Versatile Quattro sprays mortars as well as pumps self-levelling under layments

STANDARD FEATURES • Built-in air compressor • All electric power • Precision water control • 8 full bag hopper capacity • 5 to 13 gpm • Pressures up to 450 psi • Pumping distance up to 40m with height up to 20m

(based on materials)

ChemGrout Quattro Continuous Mixing Grouting System

Quattro

Maximum Output 5 – 3 gpm

Pumping Distance 40m

Pumping Height 20m

Pumping Pressure 450 psi

Power of Mixing Motor 7.5 HP

Power of Feed Motor 1.0HP

Air Compressor 8.8 CFM, 72psi, 1.2HP

Water Pressure Required 42psi

Electrical Connection 440V, 60Htz, 3 phase, 20 amps

Size 111.8 x 193 x 147.3cm (L x W x H)

Weight 185kg

Loading Height 86cm

High outputs and a consistent discharge provide a perfect fit for pumping self-levelling underlayment's

Convenient height for loading. Hopper holds 8 full bags!

Durable hopper cover protects against contamination and doubles as dust shield

Built-in handles for lifting by two people allows for easy movement

Unit disassembles in minutes for easy transportation

Sealed control box

Built in air compressor for spraying mortar, stucco & fireproofing

Large hopper holds 8 full bags

Sturdy lightweight chassis

Accurate water control system

Large wheels with locks

ChemGrout CG-550 Rugged Series • Combines ease of operation and low maintenance to provide the ultimate in performance. • Single operator system – 170 litre mixing tank, large holding hopper and centrally located controls

allow a single operator to mix, transfer and pump for continuous production. • Efficiently mixes and pumps most pre-packed non-shrink grouts and repair mortars. Materials

include bentonites, cement / sand and most slurry products • Outputs to 16 gpm (60 lpm). 400 psi (27 bar). • Power options include air, electric / hydraulic, hydraulic, gas / hydraulic and diesel / hydraulic. • Pump completely disassembles with only a hammer for fast and thorough cleaning.

APPLICATIONS

• Soil nails

• Tiebacks

• Earth anchors

• Cable & rock bolts

• Foundation stabilisation

• Soil compaction

• Pavement undersealing

• Slabjacking

• Slab raising

• Underwater foundations

• Piers

• Deep well casing

• Well sealing

• Abandonment and geothermal

Air Powered CG550/030/A

Gas / Hydraulic CG550/030/GHES

Gas / Hydraulic CG555/030/GHES

ChemGrout CG-550 Rugged Series

CG-030 Skid – Power

Maximum Output /

Pressure

Required Weight Size (L x W x H)

Air 60 lpm, 400 psi (27 bar) 100 cfm, 100 psi 141kg 162.5 x 78.7 x 73.7cm

Hydraulic 53 lpm, 400 psi (27 bar) 9 gpm, 2000 psi 132kg 162.5 x 78.7 x 73.7cm

CG-030 Rapid U-clip Disassembly

ACCESSORIES

CG550/030 Skid – Power

Maximum Output /

Pressure


Air 60 lpm, 400 psi (27 bar) 150 cfm, 100 psi 222kg 167.6 x 78.7 x 142.2cm

Hydraulic 53 lpm, 400 psi (27 bar) 2 supplies each of 9

gpm, 2000 psi 204kg 162.5 x 78.7 x 73.7cm

Electric / Hydraulic 53 lpm, 400 psi (27 bar) 3 Phase (several voltages available)

433kg 213.4 x 86.4 x 73.7cm

Gas / Hydraulic, Electric Start

53 lpm, 400 psi (27 bar) Self Contained 433kg 213.4 x 86.4 x 73.7cm

Diesel / Hydraulic 53 lpm, 400 psi (27 bar) Self Contained 476kg 213.4 x 86.4 x 73.7cm

CG-555 Trailer – Power

Maximum Output /

Pressure


Gas / Hydraulic 60 lpm, 400 psi (27 bar) Self Contained 635kg 279.4 x 152.4 x 177.8cm

Diesel / Hydraulic 53 lpm, 400 psi (27 bar) 9 gpm, 2000 psi 678kg 279.4 x 152.4 x 177.8cm

CG-030 Piston Pump Skid Mounted

Mechanical Surface Packer equipped with shut-off valve and a quick disconnect fitting

Diaphragm Protected Pressure Gauge

Water Meters available in manual or automatic. Accurately measures

the water for each batch.

Grout Hose equipped with quick disconnect fittings. Available in 7.5

& 15m lengths.

ChemGrout CG-500 Versatile Series • Highly versatile, the CG-500 handles a broad range of grouting applications including tunnels, shafts,

dams, plant maintenance and geotechnical works. • The unique twin mix tank design permits continuous pumping as each tank alternates feeding the

hopper. • This non-stop pumping process maximises the batching of materials such as neat cement, sand /

cement and most commercial pre-bagged grouts. • Two high-capacity 264 litre mixing tanks, pump and 57 litre holding hopper are all mounted on a

single skid for quick, easy set up and immediate operation. • The holding hopper includes an internal auger that keeps the material thoroughly mixed while

supplying the pump. • The open throat group pump features a non-pulsating positive displacement rotor-stator that

provides a constant discharge of materials. This progressing cavity pump is variable speed with an output of up to 20 gpm with a standard maximum pressure of 174 psi (261 psi optional)

APPLICATIONS

• Soil compaction

• Rock grouting

• Void filling

• Waterproofing

• Soil anchors

• Cable bolts

• Rock bolts

• Well encasements

• Contact grouting

• Well abandonment

• Post tensioning

• Precast

• Self-levelling floor under layments

• Slab undersealing

• Slabjacking

Specially designed mix tank provides high shearing action for thorough and complete particle wetting, producing superior grout.

ChemGrout CG-500 Versatile Series

CG-550P 2C6 3C6

Pump Open throat, non pulsating

Paddle Mixer 20 gpm (76 lpm)

Output 174 psi (12 Bar) 261 psi (18 Bar)

CG-500 Required Weight Size (L x W x H)

Air 250 cfm, 100 psi 499kg 223.5 x 86.4 x 147.3cm

Hydraulic 12 gpm, 1200 psi 476kg 223.5 x 86.4 x 147.3cm

Electric / Hydraulic 3 Phase Only (several voltages

available)

703kg 223.5 x 86.4 x 147.3cm

Gas / Hydraulic Self contained 646kg 223.5 x 86.4 x 147.3cm

Diesel / Hydraulic Self contained 737kg 254 x 86.4 x 147.3cm

CG-500GH Gas / Hydraulic

New high-strength aluminium alloy progressing cavity pump with quick access cleanout port.

ACCESSORIES



Water Meters available in manual or automatic. Accurately measures the water for each batch.

Grout Hose equipped with quick disconnect fittings. Available in 7.5 & 15m lengths.

ChemGrout CG-550 Workhorse Series • Designed to mix and pump a wide variety of materials, offering exceptional productivity, low

maintenance and quick return on investment. • Ideal for neat cements, bentonites and non-shrink grouts • The balanced design features a 170 litre mix tank, 45 litre holding hopper and ChemGrout’s unique

size 4 progressing cavity grout pump. • Mix tank is equipped with bag breaker, baffles and a variable speed high efficiency paddle that

provides high shearing action for thorough and complete particle wetting. • High strength aluminium alloy pump provides easy access for cleaning and maintenance. • Power options include air, hydraulic, gas / hydraulic, electric / hydraulic and diesel / hydraulic.

APPLICATIONS

• Pavement stabilisation

• Void filling

• Waterproofing

• Anchor, cable & rock bolts

• Encasements

• Undersealing

• Marine / underwater

• Well casing

• Machine base installation

• Column bases

• Under layments

• Slab raising

• Bridge rehabilitation

Electric CG550/2C4/EH

Air Powered CG550/2C4/A

Gas / Hydraulic CG555/2C4/GH

ChemGrout CG-550 Workhorse Series

ACCESSORIES






& 15m lengths.

CG550/030 Skid – Power Required Weight Size (L x W x H)

Air 150 cfm, 100psi 317.5kg 182.9 x 78.7 x 116.8cm

Hydraulic 12 gpm, 1200psi 272.1kg 182.9 x 78.7 x 116.8cm

Electric / Hydraulic 460/23v, 19/38A 453.6kg 182.9 x 78.7 x 116.8cm

Gas / Hydraulic Self Contained 453.6kg 182.9 x 78.7 x 116.8cm

Diesel / Hydraulic Self Contained 521.6 182.9 x 78.7 x 116.8cm

CG-555 Trailer – Power


Gas / Hydraulic Self Contained 703kg 279.4 x 172.7 x 162.6cm

Diesel / Hydraulic Self Contained 771.1kg 279.4 x 172.7 x 162.6cm

CG550 Pumps 2C4 - 2 Stage 3C4 – 3 Stage

Pump Size 4, open throat, non pulsating

Maximum Pressure 174 psi (12 bar) 261 psi (18 bar)

Maximum Output 8 gpm (30 lpm)

Mixing Tank 170 litres

Holding Hopper 45 litres

ChemGrout CG-502 Sprayer / Finisher Series • High-efficiency Sprayer / Finisher series is ideal for pouring under layments or spraying cementisous

coatings offering flexibility for both pump and spray • Standard size 4 open throat progressive cavity pump delivers a steady, non-pulsating output of

material. • Low-profile design and heavy-duty wheels allow for easy mobility through standard 81cm doorways. • Two 170 litre mixing tanks, large holding hopper and centrally located controls allow continuous

production with a single operator. • Power options include air, hydraulic, gas / hydraulic, electric / hydraulic and diesel / hydraulic.

APPLICATIONS

• Void filling

• Water proofing

• Bonded overlays

• Decorative finishes

• Machine bases

• Self-levelling floor

• Seal coating

• Finishing & resurfacing concrete

With optional 3” piston pump for higher output, multi-purpose grouting

ChemGrout CG-502/2C4 Sprayer / Finisher

CG550/030 Skid – Power

Max. Output/Pressure Required Weight Size (L x W x H)

Air 60 lpm, 400 psi (27 bar) 185 cfm, 100psi 331.1kg 182.9 x 78.7 x 116.8cm

Hydraulic* 45 lpm, 300 psi (20 bar) 2 supplies ea. Of 7 gpm,

2000psi 331.1kg 182.9 x 78.7 x 116.8cm

Electric / Hydraulic 45 lpm, 300 psi (20 bar) 3 phase only** 444.5kg 182.9 x 78.7 x 116.8cm

Gas / Hydraulic 45 lpm, 300 psi (20 bar) Self Contained 444.5kg 182.9 x 78.7 x 116.8cm

Diesel / Hydraulic 45 lpm, 300 psi (20 bar) Self Contained 444.5kg 182.9 x 78.7 x 116.8cm

• Features an open throat, size 4 progressive cavity pump and non-pulsating positive displacement rotor stator as standard.

• Allows for a steady and continuous flow of material, ideal for self-levelling under layments, fine, non shrink grouts and most other spray and injection applications. A hinged cleanout port has been added to the suction housing for quick access and clean up.

CG502/2C4 Skid – Power

Max. Output/Pressure Required Weight Size (L x W x H)

Air 30 lpm, 174 psi (12 bar) 185 cfm, 100psi 340.2kg 208.3 x 78.7 x 139.7cm

Hydraulic* 30 lpm, 174 psi (12 bar) 12 gpm, 1200psi 340.2kg 208.3 x 78.7 x 139.7cm

Electric / Hydraulic 30 lpm, 174 psi (12 bar) 1 or 3 phase** 453.6kg 208.3 x 78.7 x 139.7cm

Gas / Hydraulic 30 lpm, 174 psi (12 bar) Self Contained 453.6kg 208.3 x 78.7 x 139.7cm

Diesel / Hydraulic 30 lpm, 174 psi (12 bar) Self Contained 453.6kg 208.3 x 78.7 x 139.7cm

ChemGrout CG-502/030 Sprayer / Finisher • If higher output, multi-purpose grouting is required, the 502 series is also

offered with a single acting, variable speed piston pump. Engineered for ease of operation and low cost maintenance, the CG-030 piston pump handles a wide variety of materials ranging from fluid slurries to heavily sanded grouts.

• Unique staple lock construction holds all working components together allowing parts to be easily accessed for cleaning and maintenance.

* Hydraulic Power Packs Available ** Several Voltages Available

ChemGrout CG-570 Thick-Mix Series • Simple, powerful and built to last, the Thick-Mix Series is ideal for mixing, pumping and spraying a

wide range of materials, such as repair mortars, stucco, plasters, fireproofing and finish coats. • Powerful size 6 progressive cavity pump provides a smooth, easy to control delivery of both thick and

thin materials • A 170 litre mixing tank, large holding hopper and centrally located controls, ensure non-stop

production with a single operator. • High-strength aluminium alloy pump features easy access for both cleaning and maintenance. • Power options include air, hydraulic, gas / hydraulic, electric / hydraulic and diesel / hydraulic.

APPLICATIONS

• Cement block filling

• Waterproofing

• Slab jacking

• Void filling

• Tie backs

• Anchoring rock bolts

• Undersealing

• Slab raising

• Under layments

• Bonded overlay


• Dowel bars

• Manhole sealing

Gas / Hydraulic Powered CG-575/3C6/GH

Hydraulic Powered CG-570/3C6/H

Electric / Hydraulic Power Pack CG-PU15/EH/AC

ChemGrout CG-570 Thick-Mix Series

CG575/3C6 Trailer – Power


Gas / Hydraulic Self Contained 657.7kg 279.4 x 157.5 x 177.8cm

Gas / Hydraulic w A/C Self Contained 680.4kg 279.4 x 157.5 x 177.8cm

Diesel / Hydraulic w A/C Self Contained 737.1kg 279.4 x 157.5 x 177.8cm

• With its rugged steel construction, the versatile CG-570 Thick-Mix Series mixes and pumps a wide range of materials from thick mortars to thin finishing coats.

• Optional built-in air compressors (12 cfm for thin and 15 cfm for thick materials) allow even more flexibility for a host of spray applications.

• Easy to operate and inexpensive to maintain, these time tested grout plants provide quick set-up, smooth pumping, simple clean-up and long term durability.

• The dependable Thick-Mix Series is complete and ready for jobsite operation. The heavy-duty 170 litre mix tank is equipped with bag breaker, baffles and a variable speed high-efficiency paddle mixer that provides high shearing action for thorough and complete particle wetting.

• The tank outlet valve is a large slide gate that allows the thickest materials to fall easily into the pump’s sloped holding hopper. The CG-570’s 56 litre hopper is covered with a removable metal screen, preventing debris or dry material clumps from falling into the pump.

• Additional mixing is provided through the use of an auger inside the suction housing allowing one batch to be pumped while another is mixed, ensuring a non-stop output of material.

CG570/3C6 Skid – Power


Air 250 cfm, 100psi 340.2kg 188 x 78.7 x 134.6cm

Hydraulic 15 gpm, 2000psi 340.2kg 188 x 78.7 x 147.3cm

Hydraulic Power Packs Power Weight Size

Electric/Hydraulic w A/C 3 phase

(several voltages available) 392.3kg 144.8 x 73.7 x 111.8cm

Gas / Hydraulic w A/C Self Contained 342.5kg 121.9 x 101.6 x 91.44cm

Diesel / Hydraulic w A/C Self Contained 360.6kg 137.2 x 101.6 x 99.1cm

Large slide gate allows an easy transfer of thick materials

Hinged cleanout port provides quick access and easy clean up

A/C = Air Compressor

ChemGrout CG-570 Track Mounted Mortar Sprayer • Continuously mixes, pumps and sprays Repair Mortars, Gel Mortars, Stucco, Fireproofing and all

flowable grouts • Features ChemGrout’s patentned 3 stage, size 6, positive displacement, progressive cavity, rotor-

stator pump that will deliver 8 gpm, 300psi. • Powered by 27HP Kubota heavy duty diesel engine, equipped with electric start and variable volume,

load sensing hydraulic pump. • Air compressor / compresed air storage tank allows system to be totally self-contained providing

ability to mix, pump and spray simultaneously. • Heavy-duty tracks provide mobility for hard to get to jobsites

APPLICATIONS

• Cement block filling

• Waterproofing

• Slab jacking

• Void filling

• Tie backs

• Anchoring rock bolts

• Undersealing

• Slab raising

• Under layments

• Bonded overlay


• Dowel bars

• Manhole sealing

ChemGrout CG-580 High Pressure Series • High-production, skid mounted grout plants that provide continuous operation on a wide variety of

applications. • Designed to mix and pump neat cement, lightly sanded grouts and most commercial pre-blended,

non-shrink grout mixes. • Features double acting 3.5 x 8 high-pressure pump capable of 32 gpm and 1200 psi. • Two 484 litre mix tanks and a 113 litre holding hopper constantly feed pump for continuous

operation. • Each mixer is equipped with baffles, bag breakers and variable speed high-efficiency paddles that

provide rapid mixing. • The tank outlet valves are large slide gates that allow the thickest materials to fall easily into the

pump hopper. • The holding hopper supplies the grout pump with material for the continuous pumping operation. • Heavy-duty frame and worker platform stand up to the rugged conditions of high-volume grouting. • Power options include hydraulic, electric / hydraulic and diesel / hydraulic. • All components are easily accessible for operating, cleaning and maintenance.

APPLICATIONS

• Mining

• Tunnels

• Dams

• Soil compaction

• Rock grouting

• Water cut-offs

• Void filling

• Soil anchors


• Marine / underwater

• Precast

• Slab undersealing

• Slabjacking

ChemGrout CG-580 High Pressure Series

Double Acting Plunger Pump

Hopper Volume Max. Output Max. Pressure

3.5 x 8 Grout Pump 118 litres / minute 120 litres / minute 1200 psi (83 bar)

Model Number Description Weight Size (L x W x H)

CG/580/3.5X8/H

Skid Mounted Hydraulic Powered High Pressure Grout Plant Requires dual circuit 16 & 32 GPM., 2000 psi

816.5kg 243.8 x 94 x 182.9cm

CG580/3.5X8/EH*

Skid Mounted Electric / Hydraulic Powered Grout Plant Requires 48-60 amps, 3 Phase current, several voltage options

816.5kg

308.4kg

243.8 x 94 x 182.9cm

228.6 x 76.2 x 101.6cm

CG580/3.5X8/DH

Skid Mounted Diesel / Hydraulic Grout Plant Self contained heavy duty 45 HP diesel engine with electric start

816.5kg

521.6kg

243.8 x 94 x 182.9cm

213.4 x 76.2 x 121.9cm

* Separate Diesel or Electric power pack mounted on separate skid

ChemGrout CG-542 Rock Bolt & Cable Grouter • Low profile, compact design is ideal for the grouting of rock bolts and cable stays in mines and

tunnels. • Twin 83 litre mix tanks, large holding hopper and centrally located controls allow a single operator

continuous operation. • Special low profile design allows for easy movement and use in tight spaces such as mines and

tunnels. • Mix tanks are equipped with baffles, bag breakers and variable speed high-efficiency paddles that

provide rapid mixing. • A unique feature of these mix tanks enables the tops to be removed for quick and easy clean up. • Once the material is mixed, it passes through the large slide gates of the tank outlet valves into the

holding hopper which is equipped with an auger to keep material thoroughly mixed while waiting to advance to the pump suction housing.

• A positive displacement, progressing cavity, rotor stator type pump then delivers the material to the application.

• Operator controls are located centrally for efficient production and are easily accessible for operating, cleaning and maintenance.

APPLICATIONS

• Rock bolts

• Rock anchors pre-grouting

• Water infiltration control

• Rock / soil nails


• Shaft abandonment

Air Powered CG542A

ChemGrout CG-542 Rock Bolt & Cable Grouter

ACCESSORIES






& 15m lengths.

CG550/030 Skid – Power Required Weight Size (L x W x H)

Air 175 cfm, 100psi 362.8kg 163 x 79 x 132cm

Hydraulic 10 gpm, 2000psi 387.8kg 163 x 79 x 132cm

Electric / Hydraulic – Power Unit 3 Phase – Several Voltages Available 362.8kg 102 x 87 x 87cm

Gas / Hydraulic – Power Unit Self Contained 362.8kg 137 x 102 x 99cm

CG542 Pumps Progressing Cavity Pump Mixing Tank Holding Max.

Output

Max. Pressure

6CM3 – 6 Stage 6 Stage, Size 3, Open Throat Two – 83 litre 38 litre 3.5 gpm 522 psi (36 bar)

3C4 – 3 Stage 3 Stage, Size 4, Open Throat Two – 83 litre 38 litre 5.0 gpm 261 psi (18 bar)

Hinged clean out port provides operator easy access for maintenance and clean up.

Model 542H shown above grouting rock bolts, is ideal for non-flowable cement grouts with water / cement ratios as low as .40.

ChemGrout CG-600 Colloidal Grout Plant • Durable and efficient, the ChemGrout CG-600 offers the advantages of high-efficiency colloidal mixing

in a compact package. • Designed to meet the high-shear colloidal mixing standards specified by a growing number of

industries. • Mixer, holding tank and pump are mounted in one compact package for quick, easy set-up and

immediate operation. • Water and solid materials are drawn through the high-speed diffuser type pump rotating at speeds of

up to 2,000 RPM to prevent flocculation and achieve complete particle wetness. • Mixing time is significantly reduced by the high shear action of the colloidal mixing pump, aided by a

unique powered bridge breaker device to enhance induction. • ChemGrout’s patented 3L6A closed throat progressive cavity pump delivers a steady, non-pulsating

output of material.

APPLICATIONS

• Post tensioning

• Tunnels

• Shafts

• Mining

• Permeation grouting

• Soil & rock grouting

• Waterproofing

• Soil anchors rock bolts

• Soil nails

• Tie backs

• Earth anchors

Air Powered CG600/8CF/3L6/A

Power Pack Options CG-PU24/DH and CG-PU/EH

ChemGrout CG-600 Colloidal Grout Plant

CG600/3L6 Skid Power

Requires Weight Size (L x W x H)

Air 250 cfm, 100 psi 539.8kg 223.5 x 86.36 x 149.9cm

Hydraulic 20 gpm, 2000 psi 521.6kg 223.5 x 86.36 x 149.9cm

Pump

Pump Size 6, closed throat, progressing cavity

Maximum Output / Pressure 20 gpm (76 lpm) 261 psi (18 bar)

Power Packs Requires Weight Size (L x W x H)

Electric / Hyd – 3 Phase Several Voltages Varies Varies by Voltage

Diesel / Hydraulic 24HP Diesel / Electric Start 793.8kg 188 x 86.36 x 94cm

Colloidal Mixer

Mix Tank 8.0 cf w/ bottom cleanout

Mixing Pump 2 x 3 x 6 diffuser – type centrifugal

Holding Tank 9.0 cf paddle agitated

ChemGrout’s “Turbomix” significantly reduces mix time, enhancing flow rate and maximising jobsite operation. Specially designed tanks and mixing pumps make ChemGrout colloidal mixing efficient and economical. Ideal for use with all types of neat cements, ultra / micro-fine cements, Bentonite slurries, Flyash, Lime dust and post tension grouts.

ChemGrout CG-680 High Pressure Colloidal Series • Ideal for heavy construction projects including foundations, encasements, mining, tunnelling, anchors

and post tensioning. • High pressure and high capacity with production rates of up to 8 cubic yards per hour. • Patented double acting, positive displacement plunger pump features durable cast iron construction

for the punishing demands of high-pressure grouting. • High sheer colloidal mixer increases grout strength, while reducing mix time and enhancing flow rate. • The colloidal mixer is equipped with a 2x3x12 high shear centrifugal diffuser type pump that

disperses the cementitious material down to its finest particle size to achieve complete particle wetness.

• The mixing tank is also equipped with a variable speed high-efficiency paddle mixer that maintains a thoroughly mixed grout while waiting to be pumped.

• The grout pump is connected directly to the agitated storage tank to provide a continuous pumping operation. The grout pump is a positive displacement, high capacity, double acting plunger pump.

• The rugged steel frame stands up to the toughest conditions on the constructions site. • Operator controls are centrally located for efficient production.

APPLICATIONS

• Foundations

• Tunnels

• Mining

• Dam foundations

• Soil compaction

• Soil & rock grouting

• Waterproofing

• Soil anchors

• Rock bolts

• Encasements

• Post tensioning

ChemGrout CG-680 High Pressure Colloidal Series

Model Number Description Weight Size (L x W x H)

Air

Skid mounting electric / hydraulic powered HP colloidal grout plant.

Requires 48-60 amps, 3 phase current, several voltage options

1452kg 300 x 152 x 178cm

Hydraulic

Skid mounted diesel / hydraulic powered HP colloidal grout plant. 45 HP diesel engine with electric

start

1724kg 300 x 152 x 178cm

Pump Size Maximum Output Maximum Pressure

2” x 8” 58 litres per minute 2,000 psi (138 bar)

3.5” x 8” 120 litres per minute 1500 psi (104 bar)

High shear colloidal mixing significantly reduces mix time, enhancing flow rate and maximising jobsite operation

Available CG680 power options include Electric / Hydraulic and 45 HP Diesel / Hydraulic engine (pictured)

ChemGrout offers both manual and automatic (pictured) pressure controls on the CG680 Series.

Gunite Pumps

Antec’s range of gunite pumps are ideal for refractory application, tunnels, concrete repair, slope stabilisation, retaining walls and more. The maichines provide an even flow of materials ensuring smooth placement.

FEATURES: • Smooth output • Portable and easy to store • Versatile • Easy to maintain • Minimum labour required to operate • Rugged and reliable

SOVA Gunite Machine

• Provides a very even flow of material which allows uniform hydration and smooth placement.

• Adjustable output of material may be increased without sacrificing the quality of the application.

• The compact SOVA is capable of spraying through hoses from ¾” to 1 ½” (19-38mm) inside diameter.

• Reed’s SOVA Dry Mix Gun has the same basic operating principle that has made its LOVA style gun so successful through the world:

1. The dry mix is fed through a hopper into the pockets of the rotary feed wheel.

2. The rotary feed wheel, driven by a heavy duty oil bath gear drive, rotates the mix under the conveying air inlet and material outlet.

3. With the introduction of single source compressed air, the mix is evacuated from the feed wheel pockets and then travels through the outlet.

4. The dry mix is then conveyed in suspension through the dry mix hose to the shotcrete nozzle where water is introduced.

STANDARD FEATURES

• Oversized water separator

• Continuous feed hopper with bag breaker

• Material Agitator

• Screen and direct drive 5 hp, 8 AM, air motor

• Optional dust suppression system

• Optional hopper safety hood

APPLICATIONS

• Concrete repair

• Refractory spraying

• Rockscaping

• Slope stablisation

• Tunnels & mines

• Pools & spas

• Sewers

• Retaining & Fire walls

• Dams & Reservoirs

• Concrete Pipe

SOVA Gunite Machine (Small Open Vertical-Feed Air-Powered)

Feed Bowl

Pockets

Hose Size (I.D.)

Maximum Aggregate

Size

Air Compressor (Recommended Size at

100psi)

Maximum Output **

Common Applications

18 ¾” 1.9cm

1/8” 3.5mm

125cfm (3.5m3/min) 1.5m3/hr Fine, detailed artistic type work, rockscaping, patch, repair

18 1” 2.5cm

¼” 7mm

210cfm (6.0m3/min) 1.5m3/hr Fine, detailed artistic type work, rockscaping, patch, repair

18 1 ¼” 3.2cm

¼” 7mm

315-375cfm (9-11m3/min) 3m3/hr Refractory spraying, repair work, smooth finish

16 1 ¼” 3.2cm

¼” 7mm

315-375cfm (9-11m3/min)

4.6m3/hr Refractory spraying, repair work, smooth finish

16 1 ¼” 3.2cm

3/8” 10mm

315-375cfm (9-11m3/min)


MODEL LOVA 8-4

Maximum Horizontal Conveying Distance

ft m

1000+ 305+

Maximum Vertical Conveying Distance

ft m

300+ 91+

Drive System 5 hp, 8AM Rotary Vane Motor, Sealed Spur Gear

Hopper Continuous Feed

Gross Weight (approx.) lbs kg

435 193

** Feed Bowl, material, air system, nozzleman capability together determine maximum output. Maximum theoretical performance shown. Performance will vary depending on slump, mix design and delivery line diameter. Specifications subject to change without prior notice.

How it works 1. Material is gravity-fed from the hopper to empty

pockets of the rotary feed wheel (feed bowl) below 2. The rotary feed wheel, driven by a motor, rotates.

The material filled pocket is positioned under a compressed air chamber

3. Introduction of compressed air lifts the material out of the pocket and into the material outlet

4. Dry material is conveyed in suspension through the hose to the gunite nozzle where water is introduced to the dry material.

LOVA Gunite Machine

• LOVA provides a very even flow of material which allows uniform hydration and smooth placement.

• The adjustable output of material may be increased without sacrificing the quality of the application.

• Reed’s LOVA Dry Mix Gun has been using the same basic operating principle for over 40 years.

1. The dry mix is fed through a hopper into the pockets of the rotary feed wheel.

2. The rotary feed wheel, driven by a heavy duty oil bath gear drive, rotates the mix under the conveying air inlet and material outlet.

3. With the introduction of single source compressed air, the mix is evacuated from the feed wheel pockets and then travels through the outlet.

4. The dry mix is then conveyed in suspension through the dry mix hose to the shotcrete nozzle where water is introduced.

STANDARD FEATURES • Continuous feed hopper with bag breaker • 2 blade or 5 blade agitator • Screen and direct drive 5hp, 8AM, air motor for LOVA 8 • Screen and direct drive 9hp, 16AM, air motor for LOVA 16 • Optional electric drive motor • Optional hopper safety hood • Optional dust suppression system • Optional ultralight non-stick rotary feed wheel

APPLICATIONS • Refractory • Shotcrete • Gunite • Tunnels • Concrete Repair • Buildings • Excavations • Slope Stablisation • Rockscaping • Pools • Mines • Channels • Piers • Sea Walls • Sewers • Parks & Zoos • Retaining & Fire Walls • Dams & Reservoirs • Sand & Rock Backfill • Concrete Pipe • Ditches

* Maximum theoretical performance shown above. Performance will vary depending on slump, mix design and delivery line diameter. Specifications subject to change without prior notice.

LOVA Gunite Machine (Large Open Vertical-Feed Air Powered)

Feed Bowl

Pockets

Hose Size (I.D.)

Maximum Aggregate

Size

Air Compressor Recommended Size at

100psi

Maximum Output **

Common Applications

30 ¾” 1.9cm

1/8” 3.5mm

125cfm (3.5m3/min) 8AM 215cfm (6m3/min) 16AM

1.5m3/hr Fine, detailed artistic type work, rockscaping, patch, repair

30 1” 2.5cm

1/8” 3.5mm

210cfm (6.0m3/min) 8AM 300cfm (9.0m3/min) 16AM

1.5m3/hr Fine, detailed artistic type work, rockscaping, patch, repair

21 1 ¼” 3.2cm

¼” 7mm

315-375cfm (9-11m3/min) 8AM 375-450cfm (11-13m3/min) 16AM


21 1 ½” 3.8cm

3/8” 10mm



20 1 ½” 3.8cm

½” 13mm


6.1m3/hr Civil Construction, higher volume refractory spraying, smooth finish

15 2” 5cm

½” 13mm


9.2m3/hr Civil Construction Concrete Spraying, Less (Less Volume than with Large Aggregate system)

15 2” 5cm

5/8” 16mm


9.2m3/hr Swimming pool construction, conveying aggregate for backfill, civil construction

12 2” 5cm

5/8” 16mm


9.2m3/hr Swimming Pool Construction (Less volume than with a 2 ½” system) (15 L.A. bowl provides smoother finish)

12 2 ½” 6.3cm

¼” 19mm


11.4m3/hr Civil Construction Spraying, Highest volume (15 L.A. bowl provides smoother finish)

MODEL LOVA 8-4 LOVA 16-4

Maximum Horizontal Conveying Distance

ft m

1000 305

1000 305

Maximum Vertical Conveying Distance

ft m

300 91

300 91

Hopper Standard, tall pre-mix, short pre-mix & refractory

Standard, tall pre-mix, short pre-mix & refractory


635 288

699 312

** Feed Bowl, material, air system, nozzleman capability together determine maximum output. Specifications subject to change without prior notice.

LOHE Guncrete Gunite Machine Electrically driven dry-mix shotcrete machine

• LOHE provides a very even flow of material which allows uniform hydration and smooth placement. • The adjustable output of material may be increased without sacrificing the quality of the aplication. • LOHE uses an electric motor to rotate the machine’s material feed bowl. • An air compressor is required to convey material from the feed-bowl to the nozzle (sold separately).

STANDARD FEATURES

• Continuous feed hopper with bag breaker

• 2 blade or 5 blade agitator

• Direct drive 5 horsepower, 3 Phase Cycle Electric Motor to power feed bowl

• 50Hz or 60Hz cycles available

• 220v, 230v, 360v, 440v, 460v, 575v and others available

• Optional hopper safety hood

• Optional ultra light non-stick rotary feed wheel

APPLICATIONS

• Refractory Spraying

• Tunnel Lining

• Concrete Repair

• Buildings

• Excavations

• Slope Stabilisation

• Rockscaping

• Polls & Spas

• Mines Support

• Channels

• Piers

• Retaining & Fire Walls

• Sand & Rock Backfill

• Concrete Pipe

Operating Principal 1. The dry mix is fed through a hopper into the pockets of the rotary feed wheel. 2. The rotary feed wheel, driven by a heavy-duty oil bath gear drive, rotates the

mix under the conveying air inlet and material outlet. 3. With the introduction of single source compressed air, the mix is evacuated

from he feed wheel pockets and then travels through the outlet. 4. The dry mix is then conveyed in suspension through the dry mix hose to the

shotcrete nozzle where water is introduced.

# # Feed Bowl Pockets

Hose

Size (I.D.)

Maximum

Aggregate Size

Air Compressor (Recommended size at

100psi)

Maximum

Output**

Common Applications

1 30 ¾” (1.9cm) 1/8” (3.5mm) 125 cfm (3.5m3/min) 1.5m3/hr Fine, detailed artistic-type work, rockscaping, patch, repair

2 30 1” (2.5cm) 1/8” (3.5mm) 210 cfm (6.0m3/min) 1.5m3/hr

Fine, detailed artistic-type work, rockscaping, patch, repair

3 21 1 ¼” (3.2cm)

¼” (7mm) 315-375 cfm (9-11m3/min)

3.8m3/hr

Refractory spraying, repair work, smooth finish

4 21 1 ½” (3.8cm)

3/8” (10mm) 375-450 cfm (11-13m3/min)

4.6m3/hr

Refractory spraying, repair work, smooth finish

5 20 1 ½” (3.8cm)

½” (13mm) 375-450 cfm (11-13m3/min)

6.1m3/hr

Civil construction, higher-volume refractory spraying, smooth finish

6 15 2” (5cm) ½” (13mm) 450-600 cfm (13-17m3/min)

9.2m3/hr

Civil construction concrete spraying (less volume that with L.A. system)

7 15L.A. 2” (5cm)

5/8” (16mm) 450-600 cfm (13-17m3/min)

9.2m3/hr

Swimming pool construction, conveying aggregate for backfill, civil construction

8 12 2” (5cm)

5/8” (16mm) 450-600 cfm (13-17m3/min)

9.2m3/hr

Swimming pool construction (15 L.A. bowl provides smoother finish)

LOHE Guncrete Gunite Machine Electrically driven dry-mix shotcrete machine

* Additional air may be required depending on altitude and atmospheric pressure. * L.A. (Large Aggregate Feed Bowl) ** Feed Bowl, material, air system, nozzleman capability together determine maximum output. Specifications subject to change without prior notice.

MODEL LOHE

Maximum Horizontal Conveying Distance ft m

1000 305

Maximum Vertical Conveying Distance ft m

300 91

Hopper Standard, Tall Pre-Mix, Short Pre-Mix & Refractory


780 355

Maximum theoretical performance shown above. Performance will vary depending on mix design, delivery line diameter, and distance. Specifications subject to change without prior notice.

Dust Extractors

Dust management has become a critical OH&S issue which cannot be ignored. Antec’s range of dust extractor systems have been designed to fit over the top of an open hopper and collect fine cement dust particles.

FEATURES: • Dust hood attachment does not obscure the view into the hopper • Less waste through over filling • Less stoppages as the visibility of the hopper means a more consistent flow of

materials

• For confined jobsites (tunnels, mines and refractory jobs) • Designed to trap and stop large and small dust particles • Narrow profile allows for easy access through standard doors • Lightweight wheel mounting for one man operation and movement • Built to withstand harsh-environment conditions

STANDARD FEATURES

• 2 Horsepower 220v / 230v Single Phase Electric Motor

• Super Duty Cartridge Filter with replaceable primary element and cleanable safety element

• Cylindrical collection centre

• Complete with integral reuse access panel

• Heavy-duty quick release hood for easy filter removal

• Highly efficient, well balanced centrifugal fan

• Weight: 181kg

• Dimensions: 84 x 145 x 130cm

Dust Extractor Reed Gunite Machine Optional Accessory

Intermediate Dust Extractor

• Designed to extract / collect fine cement dust particles

• Reduces waste through increased visibility of content levels

• Helps comply with OH&S requirements for dust reduced environments (especially confined spaces)

• Available as an Air Driven or Electric Driven unit • Dust Hood Attachment designed to suite all gunite

and dry-shotcrete machines • Built to withstand harsh and demanding

environments

Australian designed and manufactured

2 Units Available Air Driven: 6hp, pneumatic valve type Airmeter complete with silencer and service kit

Electric Driven: 2hp electric motor 240V, 10 Amp, single phase, dual capacitor 5 metres of cable

Dust Hood Attachment: Available to fit all gunite and dry-

shotcrete machines. Custom made attachments available upon request.

STANDARD FEATURES

• Turbo Series Super Duty Cartridge Filter

• Heavy duty quick release lid for easy filter removal

• Cylindrical collection centre, complete with integral reuse access panel

• 20 Litre collection capacity

• High efficiency, mild pressure, curved tip centrifugal fan, with self-cleaning action

• Tightly sealed lid that can be removed for further cleaning

• Pipe connectors & fittings

• Skid mounted for portability

Advanced Dust Extractor

• Large volume, high end extractor, designed to extract / collect fine cement dust particles

• Snaptex filter bag system with reverse pulse cleaning for auto self-cleaning

• Reduces waste through increased visibility of content levels

• Helps comply with OH&S requirements for dust reduced environments (especially confined spaces)

• Available as an Air Driven or Electric Driven unit • Dust Hood attachment designed to suit all gunite and

dry-shotcrete machines • Built to withstand harsh and demanding environments

Australian designed and manufactured

2 Units Available Air Driven: 6hp, pneumatic valve type Airmeter complete with silencer and service kit

Dust Hood Attachment: Available to fit all gunite and dry-shotcrete machines.

Custom made attachments available upon request.

STANDARD FEATURES

• 1235mm x 1076mm x 2210mm high – including top fan

• 20 litre waste bin

• 20 Snaptex antistatic filter bags encased in individual galvanised cages minimising wear

• Centre pre-separation Chamber for protection of the unit against larger dust particles

• 100mm anti-static, tough line ducting

• Tool free maintenance of filter bags and galvanised cages

• Pipe connectors and fittings

• Skid mounted for portability

Electric Driven: 2hp electric motor 240V, 10 Amp, single phase, dual capacitor 5 metres of cable

Auto Self-Cleaning System: • GOYEN reverse pulse cleaning system for self-cleaning • Diaphragm valves to clean valves automatically • Sequential timer to signal valves to fire at pre-determined

intervals. • Filter regulator and auto drain included on inlet to header

tank.

Shotcrete Machines

The Clever & Co SBS Shotcrete Machines are used in some of the most demanding and adverse conditions, in refractory application, building refurbishment, tunnel construction or mining. The Clever & Co shotcrete range guarantee’s uniform material flow, virtually dust-free processing and high performance.

Shotcrete Machines - Dry

• Clever & Co Dry Shotcrete machines have an intelligent SBS control chamber system that allows the user to easily and reliably produce top quality shotcrete even in the toughest of conditions.

• Lots of small pockets load the air flow with small even portions of spraying material in the feed chamber and a constant flow of air ensure thin-flow conveying with a pulsation-free, even material flow to the nozzle tip.

• The electro-hydraulic drive in the spraying machine guarantees stepless adjustment of the material quantity by altering the speed of the pocket wheel.

• The allocator unit responsible for loading the feed chamber seals the pressurised part of the machine reliably, guarantees that the machine works in an absolutely dust-free manner and also avoids any losses of compressed air.

• A fool-proof adjustment system on the allocator ensure long service lives of the wear parts and low costs. • Sturdy flap and plug mechanisms allow the machine to be cleaned in minutes.

ADVANTAGES • Low-rebound shotcrete processing by means of even delivery flow • Dust-free machine operation due to fully contained system • Conveying distances up to 1,500m, conveying heights up to 150m • Stepless conveying capacity setting from 0.3m3/h to 15m3/h • A machine for small applications which can also be used for large quantities of shotcrete • Low wear costs due to cooling and lubrication of the wear parts • Also suitable for SPCC mortar and fibre concrete mixes • Can be used for sand-blasting and backfilling work • Sturdy design and long service life

A1N TSN / B1N C1N Type 208

Refurbishment

Express

Practical conveying capacity m3/h 0.3 – 5 0.3 – 8 5 – 15 0.3 – 5

Grain size of the aggregates Mm 0 – 12 0 – 16 0 – 16 0 – 12

Material conveyor hose connection ⌀mm 25 / 32 / 40 25 / 32 / 40 / 50 / 65

50 / 65 / 70 / 80

25 / 32 / 40

Air requirements, depending on hose ⌀ and conveying distance

m3/min 3 – 9 4 – 20 12 – 35 3 – 9

Conveying distance m Up to 700 Up to 1500 Up to 1500 Up to 700

Conveying height m Up to 150 Up to 150 Up to 150 Up to 150

Length / Width / Height mm 1720 x 910 x 1300

2005 x 710 x 1300

2275 x 1050 x 1450

3045 x 1860 x 1830

Weight kg 900 1120 / 1150 1950 1640

Shotcrete Machines - Dry

Working Principle

The feeder cone (3) acts as a sluice between the hopper (1) and the feed chamber (4) that is filled with compressed air. The pockets (8) of the rotating feeder cone (3) fill the feed chamber (4) with spraying material*. Compressed air that flows in when the pockets are emptied is relaxed via the exhaust (2) and any fine particles here are retained in a filter. To seal the sluice, the water-cooled feeder cone (3) is pushed into the centre of an elastic seal using a readjustment device. The spraying material* in the feed chamber (4) is transported from the pocket wheel (5) to the discharge area (6). The compressed air (7) flowing into the feed chamber (4) is redirected in the discharge area (6) and loaded with spraying material.

* oven-dry to earth-moist, max 5%

Shotcrete Machines – TSN Mining

• The SBS shotcrete machine type TSN “Mining” has been developed especially for underground mines where only compressed air driven machines are used.

• Using the same working principle as our longseller machines type A1N and TSN, the TSN “Mining” version includes a combination of air main drive and hydraulic power transmission.

• This feature guarantees an absolutely continuous material flow, long delivery distances and dust-free environment around the machine.

• The conveying capacity is stepless adjustable. • Robust construction and long life wear parts make this machine ideal for customers looking for

quality, reliability and environmentally friendly working.

ADVANTAGES • Pneumatic driven • Long conveying range with continuous material flow • Dust-free working • Ideal for professionals working in the toughest of conditions

TSN Mining

Practical conveying capacity m3/h 0.3 – 5

Grain size of the aggregates mm 0 – 16

Material conveyor hose connection mm 32 / 40 / 50 / 65

Conveying range m Up to 1,500

Conveying height m Up to 150

Air requirements main drive motor at 6 bar m3/min 6 - 12

Power of main drive pneumatic at 6 bar kW 8.5

Air requirement for material-mix transport depending on hose diameter & conveying distance

m3/min 4 – 20

Length / Width / Height Mm 2,010 x 710 x 1,400

Weight kg App. 1,100

Hydraulic pressure bar 200

Volume hydraulic oil l 90

Shotcrete Machines – TSN Mining

Working Principle

The feeder cone (3) acts as a sluice between the hopper (1) and the feed chamber (4) that is filled with compressed air. The pockets (8) of the rotating feeder cone (3) fill the feed chamber (4) with spraying material*. Compressed air that flows in when the pockets are emptied is relaxed via the exhaust (2) and any fine particles here are retained in a filter. To seal the sluice, the water-cooled feeder cone (3) is pushed into the centre of an elastic seal using a readjustment device. The spraying material* in the feed chamber (4) is transported from the pocket wheel (5) to the discharge area (6). The compressed air (7) flowing into the feed chamber (4) is redirected in the discharge area (6) and loaded with spraying material.

* oven-dry to earth-moist, max 5%

Shotcrete Machines – Conveying Unit

• The shotcrete conveying unit SFE for pneumatic silos works with the pocket wheel principle which achieves an absolutely uniform, surge-free material flow, even for low delivery rates.

SFE7 SFE12

Conveying capacity m3/h 0.5 – 7.0 0.5 – 12

Conveying range m Max. 800 Max. 800

Grain size aggregates mm 0 - 16 0 – 16

Material tube connection DN 32 / 40 / 50 / 65 50 / 65

Compressed air requirements, depending on tube diameter and conveying range

m3/m

4.0 – 25.0 10.0 – 30.0

Drive kW 7.5 7.5

Length / Width / Height mm 1,800 x 800 x 800 2,050 x 970 x 1,080

Weight kg ca. 430 ca. 580

HOW IT WORKS • The pocket wheel turning at the base of the feed chamber transports the shotcrete material

waiting in the feed chamber with 18 or 24 pockets. • The pocket wheel speed is fully variable in order to determine the conveying capacity. • The compressed air flowing into the feed chamber is deflected 180o in the discharge section to

the delivery line. • The air flow is charged with the shotcrete material conveyed by the pockets of the pocket wheel. • Storage of the shotcrete material in the feed chamber, balanced pressure conditions and the

controllable quantity of shotcrete material result in a smooth, thin flow of material at a constant rate.

Shotcrete Machines – PAN-DA High Pressure Pumps / Nozzles

• Ideal for shotcrete and refractory compounds

• Provides turbo mixing of the highest standard

• Suitable for all dry-spray shotcreting systems

• Practically dust-free

• Little rebound

HOW IT WORKS • The mixing water provided by a PAN-DA high-pressure pump is conveyed through a high-pressure

pipe to the nozzle at pressures of up to 100 bar. • The mixing cylinder is equipped with a special mixing pipe with a precisely calculated number of

drilled micro holes arranged in succession on altogether 4 levels. • Forcing the water through the holes, results in a small meshed water grid flowing at high speed. • The flow of material now meets the water grid at right angles. • At the moment of impact, the two flows arriving at almost the same speed generate considerable

turbulence with optimum mixing of the dry shotcreting material and the water.

San 780 San 1,100 bn pn rh 25 Additive Metering

Unit

Water delivery rate l / h 700 1,000 1,200 1,800 2,900 50 – 500

Water pressure bar 90 90 100 100 100 70

Nozzle nominal width mm 25 / 32 25 / 32 / 40 32 / 40 / 50 / 65

50 / 65 50 / 65 32 / 40 / 50 / 65

Electric motor kW 2.2 5 4 7.5 11 2.2

Length / Width / Height mm 600 x 360 x 440

600 x 360 x 440

900 x 350 x 630

900 x 350 x 630

900 x 350 x 700

730 x 500 x 400

Weight kg 40 50 130 145 165 90

Shotcrete Machines – Pre-moistening station

• Developed especially for pre-moistening dry shotcrete mixtures and refractory compounds

• Provides high-quality preliminary mixture of the building material

VBS 12 Pre-Moistening Station

Conveying capacity m3/h 0.5 – 12


Drive kW 7.5

Mains Voltage V 400

Bunker volume M3 1.0

Fill level bunker (max.) mm 2900

Transport Dimensions (L x W x H) mm 2.800 x 1.700 x 2.150

Weight kg approx. 950

ADVANTAGES • Variable height adjustment of the outlet opening • Infinitely variable adjustment speed of the pipe mixer through frequency converter • Automatic water metering • Easy to use • Compact transport dimensions, no need for components to be dismantled • Integrated rip-opener for Big-Bags • Pre-fitted for the attachment of Clever & Co SBS shotcrete machines • Easy accessibility of components at all times for cleaning and maintenance

Shotcrete Machines – A1N autark

• Clever & Co Dry A1N autark shotcrete machine for shotcrete, spray mortar and refractory materials combines the advantages of the intelligent SBS control chamber technology and the SBS PAN-DA high pressure nozzle system in a single machine.

• The hydraulic drive system is supplied with power via the quietest air cooled two-cylinder diesel engine in its class.

• The exhaust gas emissions are below the limit values for work machines in the EU, USA and Japan.

• A SPS control system as required on construction sites controls and monitors all components contained in the machine system and provides for a high degree of user friendliness and operational safety.

ADVANTAGES

• Self-sufficient power supply via Diesel engine

• Machine system for dust-free operation

• PAN-DA high pressure water pump integrated

APPLICATION AREAS

• In all locations where it is not possible to assure the required power supply

• A1N is suitable for processing all construction material mixtures to be processed by a dry spraying process:

• Shotcrete

• Spray mortar

• SPCC mortar

• The complete machine system can also be used for backfilling work and sand blasting.

• Refractory materials

• Steel fibre concrete

Shotcrete machine of type A1N autark

Practical conveying capacity m3/h 0.3 – 5


Material conveyor hose connection ⌀mm 25 / 32 / 40 / 50

Air requirements, depending on hose ⌀ and conveying distance m3/min 3 – 12

Conveying distance m Up to 700

Conveying height m Up to 150

Length / Width / Height mm 2,545x 730 x 1,360

Weight kg 1,350

Shotcrete Machines – A1N autark

High pressure pump PAN-DA Type bn Special Version

Water delivery capacity l/h 1,200

Water pressure bar 100

Spray nozzle nominal diameter mm 25 / 32 / 40 / 50

Air-cooled two-cylinder four-stroke diesel engine

Set output Approx. 20kW at 2,100 U/min

Battery capacity 24V / 85Ah

Tank capacity 60 l

Exhaust certificate according to 97/68EC, ECE R24, US-EPS IV, US-CARB-2010, CPCB India

Pan & Paddle Mixers

Designed, built and maintained in Australia, Antec’s pan and paddle mixers are the reliable, high performance choice.

FEATURES: • Range of sizes from 100kg Mini Pan to the big 2 tonne Pan Mixer • Heavy duty construction provides strength and reliability to suit the harshest of

conditions • In-house design, manufacture and maintenance for guaranteed quality • Built tough for consistent, reliable and powerful performance • Made in Australia for high quality and faster delivery

Mini Pan Refractory Mixer

STANDARD FEATURES

• 4KW – 415V 3-phase electric motor

• Replaceable liners to side and base

• Skid-mounted for forklift transport

• Electrical circuitry to AS4024.1 – Safe Guarding of Machinery

• Safety cutout switch when lid is opened

• Bag Breaker

Ideally suited for batch quantities of 3-4 bags (80-100kg)

Same heavy duty construction as Antec’s larger Mixer models

Provides the strength and reliability demanded by the Refractory Installation Industry

TECHNICAL SPECIFICATIONS • Bowl Volume:

• Depth

• Weight

• Max. Mix Volume

• Width

• Height (top of lid)

• Height (top of bowl)

• Discharge Height Based on Dense Refractory Castable material

150 litres

1000mm

400kg

65 litres

930mm

1250mm

1100mm

600mm

EP340 Pan Mixer

STANDARD FEATURES

• 10KW – 415V 3-Phase Electric Motor

• Replaceable Wear-Resistant Liners

• Skid mounted for forklift transport

• Electrical circuitry to AS4024.1 – Safe Guarding of Machinery

• Safety cutout switch when lid is opened

• Bag Breaker

OPTIONS:

• Water spray bar

• Digital water meter

• Fully controlled water dosage system

• Variable height

• Discharge chute

• Loading stand

Capable of batch quantities of up to 250kgs of dense refractory castable

Provides the strength and reliability demanded by the Refractory Installation Industry


• Depth

• Weight

• Height (top)

• Height (bowl rim)

• Width

340 litres

1250mm

740kg

1500mm

1300mm

1300mm

LCE340S Paddle Mixer

STANDARD FEATURES

• 7.5W 415V 3-Phase Electric Motor

• Replaceable Wear-Resistant Liners

• Skid Mounted for forklift transportation

• Safety Cutout switch when lid is opened

• Bag Breaker

• Manual Discharge Door

• Electrical circuitry design to AS4024.1 – Safe Guarding of Machinery

Capable of batch quantities of up to 250kgs of dense refractory castable

The heavy duty design and construction provides the strength and reliability demanded by the Refractory Installation Industry


• Depth

• Weight

• Height

• Width

340 litres

1200mm

400kg

1200mm

900mm

500kg Pan Mixer

STANDARD FEATURES

• Three section lid

• Manual bag breaker and inspection & cleanout access

• Manual discharge

• Single section platform

• Adjustable height discharge shoot 1000mm length

• Six paddle mixing configuration

• All blades, wearing surfaces & bowl liner made from Bisalloy material

OPTIONAL EXTRAS

• Attachable second section platform

• Attachable leg section to increase the discharge height

• Water tank

Pan Mixer is ideal for use in heavy duty industrial applications

Capable of batch quantities of up to 500kg

Skid mounted for easy forklift transportation

TECHNICAL SPECIFICATIONS

• Bowl Volume:

• Mix Capacity:

• Motor Capacity:

• Mixing Speed:

• Bowl Dimensions:

0.42m3

500kg (based on low cement castable 3000kg/m3)

22Kw Electric Drive

36RPM

1500mm diameter / 400mm height

1 Tonne Pan Mixer

STANDARD FEATURES

• Three section lid

• Manual bag breaker and inspection & cleanout access

• Manual discharge

• Single section platform

• Adjustable height discharge shoot 1000mm length

• Six paddle mixing configuration

• All blades, wearing surfaces & bowl liner made from Bisalloy material

OPTIONAL EXTRAS

• Attachable second section platform

• Attachable leg section to increase the discharge height

• Water tank

Large capacity Pan Mixer is ideal for use in heavy duty industrial applications

Capable of batch quantities of up to 1000kg

TECHNICAL SPECIFICATIONS

• Bowl Volume:

• Mix Capacity:

• Motor Capacity:

• Mixing Speed:

1.186m3

1000kg (based on low cement castable 3000kg/m3)

30Kw 415V 50Hz

36.2RPM

Parts, Accessories & Maintenance

Antec stock and supply a wide range of parts and accessories for all Concrete & Grout Mixer Pumping Equipment. Additionally we offer a repair and maintenance service to ensure the ongoing efficiency and effectiveness of your equipment.

INCLUDES: • Spare Parts:

• Concrete Pumps • Grout Mixers & Pumps • Gunite Pumps • Shotcrete Nozzles

• Water Pumps

• Dust Helmets

Trailer Mounted Concrete Pumps Spare Parts

Optional Mixer Attachment

ChemGrout Grout Mixer Pump Accessories

GAUGES

Protected Pressure Gauge In-line mounting accurately measures grout discharge pressure. Gauge is equipped with quick disconnect fittings that easily snaps into grout line and is protected from grout contamination by a diaphragm seal. Available for 1” and 1 ¼” sizes (larger upon request) and various discharge pressures.

High Pressure Gauge Accurately measures the grout pump discharge pressure. Available for 1” and 1 ¼” hose sizes and various discharge pressures. Equipped with hose couplings to easily snap into the grout line. The gauge is protected from grout contamination by a diaphragm seal. 1” locking stainless steel camlocks. Ranges 0-1500, 0-2000, 0-3000psi.

Inline Protected Pressure Gauge Non-clogging pressure sensor protects instrumentation and ensures accurate, pressure measurements. A full 360 degree circumferential diaphragm isolates the instrumentation from process material, thus preventing clogging and can be flushed clean without removal or disassembly. The Protected Gauge Assembly includes 1” or 1 ¼” camlock fittings (larger upon request) and is available for all ChemGrout equipment with working pressures of up to 1000 psi.

GROUT HEADERS

Standard Grout Header Grout header controls pressure of circulating injection systems. Consists of one diaphragm type throttling valve, one standard protected gauge and shut-off valve. All components plumbed together with standard NPT fittings and are provided with cam lock style couplings compatible with grout hose.

In Line Grout Header Grout header controls pressures of circulation injection systems. Consists of one diaphragm type throttling valve, one in-line non-clogging protected gauge and shut-off valve. All components plumbed together with standard NPT fittings and are provided with camlock style couplings compatible with grout hose.

High Pressure Recirculating Assembly High pressure grout headers are used to control pressure during grout injection. The headers use regulating valves and a pressure gauge to bypass grout back to the agitator tank. Headers are available for 0-1000 psi, and are equipped with 1” locking style camlock fittings.


PACKERS

Drive Packer Designed for easy insertion and removal for 1” injection holes commonly used in slab jacking and void filling. Comes complete with hose couplings, reinforced drive head and shut-off valve. Available in both 1” and 1 1/14” hose fittings.

Mechanical Surface Packer Comes complete with shut-off valve, spinner, expandable rubber end and quick disconnect fitting. Packers are available for hole sizes of 1 ½” to 6” diameter with a standard length of one foot. Longer lengths of up to 10 feet are available upon request.

Inflatable Grout Packers Inflatable packers are available in diameter sizes of 1-2”, 2-3”, 3-6”, 4-7” and 5-8”. Standard lengths are 15”, 30”, up to 60” or more. A sliding head design can double in size from their run-in diameter furnishing a longer seal than that of a mechanical packer. Integral tube scrapers remove excess grout adhered to the outside of the centre tube and work each time the packer is deflated.

SPECIALTY TOOLS

Corkscrew Packing Puller Removes Teflon or graphite packing rings from all ChemGrout pumps. Allows user to quickly change packing sets without disassembly of pump.

Piston Pump Ball Seat Remover Quickly and easily removes ball seats from ChemGrout’s popular CG050 & CG030 piston pumps.

Ball Seal Remover / Installer Save time and do it right the first time. Easily aligns double tapered steel ball seats on all ChemGrout high-pressure plunger pump models.

Slide Hammer Staple Puller “U-Clip” remover for use on all Model 030 three inch piston pumps. Quickly pulls out clips from pump housing.

HP Slide Hammer Staple Puller Removes all High-Pressure plunger pump parts quickly and easily. A must for saving time on pump cleaning and maintenance.


WATER BATCHERS & FLOW METERS

Double Water Batcher Manually operated water batcher with adjustable overflow pipe and 2 quick discharge dump valves. Various sizes available for double mix tanks.

Single Water Batcher Manually operated water batcher with adjustable overflow pipe and quick discharge dump valve. Various sizes available for single mix tanks

Fill-Rite Water Meter With a rated accuracy of +/- 1%, these meters measure the quantity of water, improving batch quality and productivity. Weatherproof and corrosion resistant, they are totalising and resettable. Equipped with inlet strainers, mounting bracket and shut-off valve, meters are available in 20 and 40 GPM flow rates.

Neptune Water Meter Accurately measure water volume with a rated accuracy of +/- 1%, improving batch quality and productivity. Models with manual or automatic shut-offs are available, both using counters that are totalising and resettable. Equipped with inlet strainers and discharge hoses.

Magnetic Grout Flow Meter Measures the flow rate (at a maximum measuring error of 0.5%) at a convenient location between the grout pump and the point of injection. Flow meters are preconfigured to suit the customer requirements for units of measure and flow ranges. Includes digital display, resettable totaliser, 4-20mA output signal and protective stand.

AIR COMPRESSORS

Air Compressor – 15 cfm @ 90 psi Optional air compressor available on select models for spray applications of coatings and bonded overlays.

Air Compressor – 29 cfm @ 90 psi Optional high volume air compressor available on select models for spray applications of vertical and overhead repair mortars.


HOPPER SCREENS Thick Mix Hopper Screen Heavy duty hopper screen with wide grid pattern used for thicker grouts, allowing for better flow to holding hopper.

Fine Hopper Screens Hopper screens use a tight pattern that helps filter out any large particles or debris from the mix tank before it reaches the pump. Best used with more flowable grouts.

Mini Series Hopper Screens Round hopper screens use a tight pattern that helps filter out any large particles or debris before it reaches the pump. Best used with more flowable grouts.

SPRAY WANDS / HOSES Spray Wand Multi-purpose wand allows user to accurately control both spray pattern and density. Equipped with grout hose coupling with swivel, air hose fitting with ball valve and needle valve for precise air control. A rubber cap is added for safety and 6 orifice sizes from ¼” to 5/8” are standard. Available for both 1” and 1 ¼” hose sizes.

Compact Spray Wand Designed for spraying repair mortars in confined areas. The unique nozzle design injects a uniform air flow, providing a smooth and consistent spray pattern. Equipped with grout hose coupling, air hose fitting and air control valve, this compact wand is available for both 1” and 1 ¼” hose coupling.

TESTING Mud Balance & March Funnel Kit Provides a simple method for accurate determination of mud density. Complete with break resistant carrying case, the Marsh Funnel / Cup measures mud viscosity.

Flow Cone & Stand Meausre the flow properties of fluid hydraulic grout mixes. Features a cast aluminium flow cone with a stainless steel orifice.


MISCELLEANEOUS

Hand Mixer Lightweight, high performance hand mixer. Operates on a 110-120 volt heavy duty 1 HP motor. A variable speed drive reduces splashing, while blending batches as large as 30 litres. Extended shaft minimises back strain. Perfect compliment to CG050M & CG050 grout pumps.

Model 320 Power Washer Hydraulically powered pressure washer cleans machine at 2000 psi/3 gpm. Includes 15 metre hose, trigger gun with adjustable nozzle.

CG550/CG500 Remote Controls Remotely controls pump operation on a wide variety of ChemGrout equipment. Available in air or hydraulic power options.

Water Pump Self-priming centrifugal pump is ideal for transferring water from source to mix tank(s) or water batcher at up to 120 gpm, with suction lift of up to 6m. Pump includes built-in check valve and variable speed control.

Grout Hose Heavy duty grout hose with abrasion resistant lining. Equipped with internally expanded ends for full material flow and quick disconnect fittings. Available in 1”, 1 ¼” and 2” I.D. with working pressures of up to 500psi. High pressure hose also available at a working pressure of 1000psi.

Hose Whip These strong steel cables prevent hose whip in case of accidental separation of hose coupling. Reaches across the hose fittings to provide standby safety for hose. Spring-loaded loops in the cable ends open easily to pass over the couplings for a firm grip on the hose. Maximum working pressure 200 psi for air.

Cleaning Sponge Balls These balls will allow you to mechanically clean grout hoses. Available for hoses in 1” and 1 ¼” sizes.

SOVA PARTS

COMPLETE NOZZLE ASSEMBLY

PART ID DESCRIPTION IMAGE

AN995P Complete Nozzle Assembly 1 ½"

Double Bubble type

C/with Hydration Extension

Refer Reed Part # RD12078

AN995P-1.5

Complete Nozzle Assembly 1 ½"

Double Bubble type

C/with 1500mm Hydration Extension

RD12001 1" Nozzle Assembly, includes:

1. RD12052 Water Nozzle Body 2. RD12041 1" Gum Linner 3. AN1003 Reducer Nipple 4. AN947 Needle Valve 5. RD12064 Brass Water Ring 6. RD12070 Rubber Washer 7. AN943 Minsup 3/8" Male Threaded A-type Claw coupling

CLC105098 Turbo Mixing Spray Nozzle "ULTRA" DN 38/38x11, 0.6mm Al,

cylindrical, duct Vulkolan, complete

CLC105058 Turbo Mixing Spray Nozzle "ULTRA" DN 32/32 x 10

0.6mm, Aluminium, cylinder, RV Vulkolan, DN 10, complete

SOVA PARTS

BASE GEAR ASSEMBLY

REF NO PART ID DESCRIPTION IMAGE

3 RD20149 Spindle Sova Assembly includes:

RD10737—Locking Nut Spindle

RD20026—Spindle for Sova

RD20027—Bearings Spindle (Upper & Lower)

RD20028—Spindle Housing

RD20029—Seal for Spindle

6 RD20036 Top Bearing No Picture Available

11 RD20037 Bottom Bearing No Picture Available

15 RD10736 Lock washer for Spindle

19 RD20042 Spindle gasket No Picture Available

SOVA PARTS

BASE ASSEMBLY


2 RD10738 Locknut

Hex Flex ¾ —16

4 RD10714 Washer—¾ ̎

White Felt

5 RD10713 Wheel

6 RD20035 Drive Gear 8am

SOVA PARTS

DRIVE SPINDLE ASSEMBLY


RD20149 Sova Spindle Assembly

2 RD20029 Seal No Picture Available

3 RD20026 Spindle—Sova/209 No Picture Available

7 RD20042 Gasket No Picture Available

SOVA PARTS

HOPPER & PAD

SOVA PARTS

HOPPER & PAD


4 RD20388 Rock Shear

Suit Sova & 209

8 RD20090 Rubber Wear pad

Suit Sova 16 & 18 pocket bowls

12 RD20069 Pad Clamp Rubber Sova

Replacement Rubber for Sova Pad Clamp

16 RD10945 Blades—Bag Breaker

18 RD20077 Hopper Sova 111 No Picture Available

19 RD20098 Sova Agitator

20 RD20089 Feedbowl 16PKT Sova

RD20189 Feedbowl 18PKT Sova

21 RD20172 Riser Plate

⅛ ̎ Thin


¼ ̎ Medium


⅜ ̎ Thick

SOVA PARTS

HOUSING ASSEMBLY


11 RD10092 Chain Pad—Adjusting Short

10 RD10093 Chain Pad—Adjusting Medium

9 RD10094 Chain Pad—Adjusting Long

8 RD20187 Knob Guide Assembly

13 RD20188 Stud Guide Assembly

SOVA PARTS

KNOB GUIDE ASSEMBLY


RD20187 Knob Guide Assembly

3 RD20003 Knob—Pad Adjusting

8 RD20004 Chain Cog

SOVA PARTS

ADJUSTING ASSEMBLY


RD20188 Stud Guide Assembly

2 RD20004 Chain Cog

6 RD20001 Nut Pad Adjusting Jam

SOVA PARTS

PAD BACKUP ASSEMBLY


3 RD71662 90˚ Elbow—HD No Picture Available

5 RD71550 Reducing Elbow—HD

4 ̎ to 3 ̎ Reducing Elbow—HD

No Picture Available

RD71565 Reducing Elbow—HD

5 ̎ to 4 ̎ Reducing Elbow—HD


6 RD20146 Crossover Hose Sova 111

1.25 ̎ x 13.00 ̎ OAL

8 RD10042 Gooseneck 1 ½ ̎ Linertype

RD10043 Gooseneck 1 ¼ ̎ Solid

RD10959 Liner—Suit 1 ½ ̎ Gooseneck Liner

10 RD20092 Pad Back Up Plate Sova

Steel Back Up Plate for Sova Wearpad

Suits Sova 3, 4 and 7

SOVA PARTS

AIR MOTOR ASSEMBLY


15 RD10601 Gasket—Body Spacer

16 RD10602 Vanes 8am Motor

12 RD10605 Repair Kit—8am Motor

SOVA PARTS

FEED WHEEL ASSEMBLY


1 RD20098 Agitator—Sova

2 RD20089 Feedbowl 16 Pocket Sova

RD20189 Feedbowl 18 Pocket Sova

RD20172 Riser Plate Thin ⅛ ̎ Sova

RD20173 Riser Plate Medium ¼ ̎ Sova

RD20174 Riser Plate Thick ⅜ ̎ Sova

LOVA PARTS

COMPLETE NOZZLE ASSEMBLY

PART ID DESCRIPTION IMAGE

RD50POLY 2" poly dry Gunning Nozzle, includes:

1 - Part number WR50 - Water Ring NW50 1 Off

2 - Part Number NRWA - Neoprene Washer 2 off

3 - Part Number NN50 - Nozzle Nut NW50 1 off

4 - Part Number UNT50 - Nozzle tip 450mm (Conical Plastic) 1 off

5 - Part Number HE50 - Male Threaded Hose Tail to suit NW50 Nozzle

Body 1 off

AN995P Complete Nozzle Assembly 1 ½"

Double Bubble type

C/with Hydration Extension

Refer Reed Part # RD12078

AN995P-1.5

Complete Nozzle Assembly 1 ½"

Double Bubble type

C/with 1500mm Hydration Extension

CLC105088 Turbo Mixing Spray Nozzle "ULTRA" DN 50/50 x 12, 0.6mm

Aluminium, cylinder, RV Vulkollan, DN13, kpl

CLC10598 Turbo Mixing Spray Nozzle "ULTRA" DN 38/38x11, 0.6mm Al,

cylindrical, duct Vulkolan, complete

LOVA PARTS

BASE GEAR ASSEMBLY

LOVA PARTS

BASE GEAR ASSEMBLY


6 RD10705 Gasket—Spindle Housing

8 RD10716 Bearing— ⅝ ̎ Deep

Drive train bearing—Upper

Stages 1 and 2 (2 per machine)

10 RD10720 Shaft—Pinion Gear Stage 1

11 RD10721 Reducer Gear 5 ̎

Stage 1

13 RD10723 Bearing ¾ ̎ Deep

Drive train bearing—Lower

Stages 1 and 2 (2 per machine)

14 RD10724 Shaft—Pinion Gear Stage 2

15 RD10722 Gear 6 ̎

Reducer Gear—Stage 2

19 RD10736 Lock Washer—for Spindle

20 RD10715 Splined Bull Gear No Picture Available

LOVA PARTS

DRIVE SPINDLE ASSEMBLY


2 RD10728 Spindle Stud

Drive Pins for Bowl (3 per machine)

3 RD10729 Lova Spindle

5 RD10702 Spindle Bearing

6 RD10703 Spindle Housing

Output Drive Spindle Housing

7 RD10704 Bearing—Lower

Lower Bearing for Output Drive Spindle

8 RD10737 Locknut for Spindle

RD10705 Gasket—Spindle Housing

RD10736 Lock Washer for Spindle

LOVA PARTS

HOPPER & PAD

LOVA PARTS

HOPPER & PAD


4 RD10827 Riser Plate—Thin ⅛ ̎

2 RD10825 Riser Plate—Medium ¼ ̎

3 RD10826 Riser Plate—Thick ⅜ ̎

5 RD108110 2 ̎ Blade Agitator Lova

6 RD20075 Knob—Pad Clamp

Lova IV/ Sova III

7 RD20072 Block—Pad Clamp

Sova III/ Lova IV/ 209/ 215 / LOHE

8 RD10039 Pad Clamp Weldment

Welded Bracket and Rubber Strip Assembly

11 RD10907 Screen—Lova Hopper

Mesh Screen for Refractory Hopper

12 RD10939 Bag Breaker

Frame Assembly complete with Blades

Suit Lova Refractory Hopper

LOVA PARTS

FEED WHEEL PAD HOUSING


3 RD20066 Swivel Bolt Assembly

7 RD10928 Stud—Pad Clamp

8 RD10005 Seal Felt

½ x 1 x 36 ¼ ̎ Lova IV/ VI 25mm x 16 mm x 915 mm

12 RD10040 Pad Housing Assembly Lova

Pad Clamp and Adjusting Assembly

Complete with A—Housing, Chain Drives, Studs etc.

LOVA PARTS

KNOB GUIDE ASSEMBLY


RD20187 Knob—Guide Assembly

3 RD20003 Pad—Adjusting Knob

5 RD20021 Knob—Pad Clamp Stud No Picture Available

8 RD20004 Chain Cog

LOVA PARTS

PAD HOUSING ASSEMBLY


RD10040 Pad Housing Assembly

Pad Clamp and Adjusting Assembly

Complete with A-housing, Chain Drives, Studs etc.

12 RD10076 Top—Pad Housing

For Chain Drive and Stud Assembly mounting

14 RD10077 Side—Pad Housing

A—Side Pad Housing for Rockshear and #10076 Mounting

8 RD20075 Pad Clamp Knob

For Lova 4 and Sova 3

RD10096 Chain Cover—Pad Housing Right and Left No Picture Available

RD10047 Stud Assembly—Pad Adjusting

Stud and Shaft for Pad Pressure ( 3 per machine)

RD10094 Chain Pad Adjusting—Long No Picture Available

RD20182 Gasket—Pad Housing Right and Left

13 RD20187 Knob—Guide Assembly

LOVA PARTS

PAD ADJUSTING STUD ASSEMBLY


RD10047 Pad Adjusting Stud Assembly

Stud and Shaft for Pad Pressure (3 per machine)

2 RD20004 Chain Log

6 RD20001 Nut Pad—Adjusting Jam

LOVA PARTS

PAD BACKUP ASSEMBLY

LOVA PARTS

PAD BACKUP ASSEMBLY 1


3 RD10260 Lova Cross Over Hose

Air Inlet Hose 1 ¼ ̎ BSP

6 RD10042 Gooseneck—1 ½ ̎ Linertype

Uses RD10959 Liner

RD10044 Gooseneck—1 ½ ̎ Solid

Course Thread

RD10045 Gooseneck—2 ̎ Solid Cast

RD10046 Gooseneck—2 ̎ Linertype

Uses RD10958 Liner

7 RD10958 Liner—Suit 2 ̎ Gooseneck

2 ̎ I/D Liner for #10046 Gooseneck

RD10959 Liner—Suit 1 ½ ̎ Gooseneck

1 ½ ̎ I/D Liner for #10042 Gooseneck

RD60010 Pad Back Up Plate 1.5 ̎

Suits 1 ½ ̎ Solid and Linertype Goosenecks for Large Aggregate

(LA—Offset) Bowls

RD60012 Pad Back Up Plate

Suits 1 ¼ ̎, 1 ½ ̎ and 2 ̎ Solid Goosenecks

Also 1 ½ ̎ Linertype Goosenecks for Standard (Centre divide)

Bowls

8 RD10953 Pad Back Up Plate 2 ̎ Offset

Steel Backup Plate for #10336 Rubber Wear Pad 2 ̎ Offset

2 RD10797 Feedbowl—12pkt with Dividers

LOVA PARTS



3 RD10798 Wearpocket 12pkt Dividerless

RD10799 Feedbowl 12pkt Dividerless No Picture Available

RD10800 Wearplate 15pkt Centre

RD10801 Feedbowl 15pkt Centre

RD10802 Wearplate 15pkt Offset

RD10803 Feedbowl 15pkt Offset

RD10805 Wearplate 20pkt

RD10806 Feedbowl 20pkt

RD10807 Wearplate 21pkt



LOVA PARTS



4 RD10922 Rock Cone for Offset Bowl Types

Requires RD10014 Narrow Rock Shear

5 RD10013 Rock Shear

Standard (Wide)

RD10014 Rock Shear (Narrow)

8 RD11019 Hose End—Female 1 ½ ̎ Course

7 RD11037 Coupling Nut 1 ½ ̎ Course

11 RD10336 Wear Pad (Rubber) 12 and 15pkt

Offset Divider—Large Aggregate Rubber Wearpad (Suit 12 and

15 Pocket Bowls) These are for offset Divider Bowls

RD10338 Wear Pad—Lova 15 and 20pkt Standard pocket Rubber

Wearpad (Suit 15 center divider and 20 Pocket Bowls)

RD10339 Wear Pad (Rubber) 21 and 30pkt standard

(Suit 21 and 30 Pocket Bowls)

LOVA PARTS

8AM AIR INLET ASSEMBLY


8 RD10290 1 ¼ ̎ BSP Ball Valve for Material Feed Air

14 RD10270 ½ ̎ Needle Valve Inline No Picture Available

15 RD13300 Air Filter Assembly 8AM

½ ̎ BSP Inlet/ Outlet, Zinc Bowl with Sight Glass

17 RD10322 Lubricator Oil 8AM

½ ̎ BSP Inlet/ Outlet , Zinc Bowl

20 RD12050 Bronze Needle Valve ½ ̎ 90˚

20 RD12050A Handle for 12050 Needle Valve

LOVA PARTS

16AM AIR INLET ASSEMBLY


8 RD10290 1 ¼ ̎ BSP Ball Valve for Material Feed Air

12 RD10281 1 ̎ BSP Ball Valve Motor On/ Off

For Air Supply to Motor


14 RD10323 Air Filter Assembly 16AM

1 ̎ BSP Inlet/ Outlet, Zinc Bowl with Sight Glass

18 RD10284 1 ̎ BSP Needle Valve Motor Speed

For Air Motor Speed Control

LOVA PARTS

8AM AIR MOTOR


RD10600 8AM 5HP Air Motor

RD10605 8AM Air Motor Repair Kit

Replacement Bearings, Seals and Gaskets

15 RD10601 Gasket Body Spacer 8AM Air Motor

16 RD10602 Vanes 8AM Air Motor

Vanes for #10600 8AM Motor (4 per unit)

LOVA PARTS

16AM AIR MOTOR


RD10603 16AM 9HP Air Motor

RD10606 16AM Air Motor Repair Kit

Replacement Bearings, Seals and Gaskets

18 RD10608 Gasket 16AM Body Spacer

19 RD10604 Vanes 16AM Air Motor

Vanes for #10603 16AM Motor (6 per unit)

1.5” Poly Nozzle Assembly

Material is pre dampened at the rear, allowing improved hydration by the time the material arrives at the nozzle.

Results in Less Dust

Safer Working Conditions

Ideal for dry gunning operations

FRAS Rated Hose & Fittings

Hose Length 1.5m. Diameter 38mm. Double Bubble Style

Clever & Co Nozzle

• German manufacture • Replaceable mixing tube • Pulls apart without the use of tools • Fitted with needle valve offering fine water adjustment • Aluminium construction… tough and long lasting • Nozzles come with cleaning needles for hydration holes • Provides dustless results

2” Nozzle – Turbo Mixing Spray Nozzle “ULTRA” DN50 Code - CLC103258

1 1/2”Nozzle – Turbo Mixing Spray Nozzle “ULTRA” DN38 Code: CLC105098

1 ¼”Nozzle – Turbo Mixing Spray Nozzle “ULTRA” DN32 Code: CLC105058

Double Bubble Nozzle

The Double Bubble Nozzle is our most popular nozzle assembly. The double chamber inside the nozzle tip is designed to provide additional hydration of the sprayed material.

Variable lengths of extension hose can be used between the water-body and the nozzle tip to allow for further hydration of the material prior to it exiting the assembly.

AN980 Double Bubble Nozzle

AN923P Nozzle Nut

AN986FP Female Hose Adaptor Poly AN999 38mm

Hose Section x 300mm

AN986MP Male Hose

Adaptor

AN943 Minsup Hose Connector

SP1002 Spirolet Nozzle Nut

SP1000 Spirolet Nozzle

Water Booster Pump Air drive, high pressure

PUMP • Rotary gear, positive displacement flow • Maximum discharge pressure: 100 PSI • Maximum suction lift: 6.1 metres (20ft) • Operating temperature range: -40C to 2040C • Adjustable discharge pressure relief • Pipe size: 1.9cm (¾ inch)

The by-pass valve is used to regulate and relieve discharge pressure. To increase pressure, loosen locknut and turn by-pass adjusting screw clockwise (factory set at 50PSI).

DRIVE • The Reed 4025 water pump is air motor driven and equipped with an air filter, air regulator and air

lubricator. • Maximum recommended operating pressure (air) is 100 PSI. • Air lubricator: use S.A.E. No. 10 detergent motor oil, one drop every 15 to 30 seconds. Capacity: Water 150C


R.P.M FT. HD.

P.S.I.

0

0

46

20

92

40

138

60

184

80

231

100

290

125

346

150

400

L.P.M.

H.P.

MOTOR

15

.50

¼

13.05

.23

¼

10.98

.30

1/3

8.9

.39

½

5.6

.55

½

4.9

.65

¾

4.9

.70

¾

3.8

.90

1

600

L.P.M.

H.P.

MOTOR

23.8

.25

¼

21.8

.30

1/3

19.9

.40

½

17.9

.65

¾

15.9

.75

¾

14.9

.95

1

13.2

1.15

1 ½

11.7

1.40

1 ½

800

L.P.M.

H.P.

MOTOR

32.4

.30

1/3

30.9

.40

½

29.4

.58

¾

27.9

.85

1

26.4

.93

1

24.8

1.15

1 ½

17.4

1.40

1 ½

23.4

1.70

2

1000

L.P.M.

H.P.

MOTOR

41.2

.40

½

39.7

.60

¾

38.3

.70

¾

36.7

.90

1

35.3

1.1

1

33.8

1.38

1 ½

30.2

1.60

2

29.9

1.92

1

1200

L.P.M.

H.P.

MOTOR

50.4

.50

½

48.9

.70

¾

47.5

.85

1

46.0

1.08

1

44.5

1.35

1 ½

43.0

1.65

2

42.3

1.90

2

42.0

2.20

3

1600

L.P.M.

H.P.

MOTOR

68.7

.70

¾

67.3

.91

1

65.9

1.20

1 ½

64.4

1.50

1 ½

63.0

1.80

2

61.6

2.14

2

60.9

2.50

3

60.5

2.90

3

1725

L.P.M.

H.P.

MOTOR

75.1

.80

1

73.7

1.10

1

72.3

1.42

1 ½

70.9

1.85

2

69.5

2.18

2 ½

68.1

2.65

3

67.0

3.00

3

65.8

3.60

5

H.P. = ACTUAL HORSEPOWER

MOTOR = CONVENIENT FRACTIONAL SIZES

L.P.M. = LITRES PER MINUTE

P.S.I. = LBS. PER SQUARE INCH PRESSURE

FT. HD. = EQUIVALENT PRESSURE IN FEET OF WATER

R.P.M. = REVOLUTIONS PER MINUTE

*CONSULT FACTORY FOR PRESSURES OVER 100 P.S.I.

Operational Note:

• Gear pumps are self-priming, however, on initial or dry

start-up, it is recommended that gears be wet.

• Service life of pump will be increased if liquid pumped

is clean and has lubricity valve

• When possible, flush pump after each use

Air Motor Data


R.P.M FT. HD.

P.S.I.

0

0

1.399

20

2.79

40

4.19

60

5.59

80

7.03

100

8.82

125

10.53

150

400

L.P.M.

H.P.

MOTOR

15

.50

¼

13.05

.23

¼

10.98

.30

1/3

8.9

.39

½

5.6

.55

½

4.9

.65

¾

4.9

.70

¾

3.8

.90

1

600

L.P.M.

H.P.

MOTOR

23.8

.25

¼

21.8

.30

1/3

19.9

.40

½

17.9

.65

¾

15.9

.75

¾

14.9

.95

1

13.2

1.15

1 ½

11.7

1.40

1 ½

800

L.P.M.

H.P.

MOTOR

32.4

.30

1/3

30.9

.40

½

29.4

.58

¾

27.9

.85

1

26.4

.93

1

24.8

1.15

1 ½

17.4

1.40

1 ½

23.4

1.70

2

1000

L.P.M.

H.P.

MOTOR

41.2

.40

½

39.7

.60

¾

38.3

.70

¾

36.7

.90

1

35.3

1.1

1

33.8

1.38

1 ½

30.2

1.60

2

29.9

1.92

1

1200

L.P.M.

H.P.

MOTOR

50.4

.50

½

48.9

.70

¾

47.5

.85

1

46.0

1.08

1

44.5

1.35

1 ½

43.0

1.65

2

42.3

1.90

2

42.0

2.20

3

1600

L.P.M.

H.P.

MOTOR

68.7

.70

¾

67.3

.91

1

65.9

1.20

1 ½

64.4

1.50

1 ½

63.0

1.80

2

61.6

2.14

2

60.9

2.50

3

60.5

2.90

3

1725

L.P.M.

H.P.

MOTOR

75.1

.80

1

73.7

1.10

1

72.3

1.42

1 ½

70.9

1.85

2

69.5

2.18

2 ½

68.1

2.65

3

67.0

3.00

3

65.8

3.60

5

H.P. = ACTUAL HORSEPOWER

MOTOR = CONVENIENT FRACTIONAL SIZES

L.P.M. = LITRES PER MINUTE

P.S.I. = LBS. PER SQUARE INCH PRESSURE

FT. HD. = EQUIVALENT PRESSURE IN KG/CM2

R.P.M. = REVOLUTIONS PER MINUTE

*CONSULT FACTORY FOR PRESSURES OVER 100 P.S.I.

Operational Note:

• Gear pumps are self-priming, however, on initial or dry

start-up, it is recommended that gears be wet.

• Service life of pump will be increased if liquid pumped

is clean and has lubricity valve

• When possible, flush pump after each use

Air Motor Data

High Pressure Water Pump (single phase)

Ideal for dry gunning operations

Provides better hydration at the nozzle thereby reducing dust

TECHNICAL DATA • Water-output rate: 430l/h • Maximum water pressure: 140 bar (2030 psi) • Adjusted water pressure: 100 bar (1450 psi) • Max. water temperature: 70oC • Supported nozzle dia. 25 / 32 / 38mm (depending on special water requirement of the material)

• Drive: Single phase motor 240V / 15 amp • Power: 2.2kW (at 140 bar)

1.5kW (at 100 bar) • Weight: app. 40kg • Water input: ¾” GEKA coupling • Water output: High pressure coupling, DN10

Pre-Dampener for Pre-Mixed Materials with collapsible main auger for underground mines & tunnels

• Handles most pre-blended materials that may need to be pre-dampened which assists with dust control. • Moisture content is precisely controlled by engineered spray jets. • Quick release of rubber troughs allows instant access to augers for easy cleaning. • Available in electric 415V or air operated. • Can also be used as a conveyor of material to open top rotary guns (such as Reed) and mixers.

STANDARD FEATURES • Precise water / material ratios

• Handles all kinds of dry and pre-mixed materials

• Handles up to ½” (12mm) aggregates

• Output capacity up to 215kgs per minute (13 tonnes per hour)

• Complete with water meter assembly

• One-man operation, easy to clean, no waste

K80 E Series Respirator – Gases and Industrial Dusts

• The K80E series of respirators function by means of a slight over pressure which is created inside the helmet by a flow of filtered air.

• A battery powered blower unit draws air through filters and sends it through a breathing tube to the inside of the helmet.

• Blower unit, filters and battery are worn at the waist.

STANDARD FEATURES

• CE certified, Italian design

• Wide view fixed visor

• Complete protection of the head, face, ears, neck and respiratory system

• Real positive pressure makes breathing comfortable even under strain

• Fits most head sizes and accommodates beards and eye-wear

• Not affected by temperature changes and ultra violet rays

• Uniform airflow distribution

• Compact, heavy duty blower units

• Battery charger with microprocessor controlled charging functions

• High efficiency, long life filters

TECHNICAL INFORMATION

• Helmet Material Fibre Glass

• Colour White

• Visor Fixed

• Size Adj. 53-63cm

• Noise Level < 75dB

• Accessories Worn at waist

• Weight 900g

RESPIRATOR VERSIONS K80E T8 (0313084) •Helmet with T8 blower unit, two ZP3 HEPA filters, one rechargeable 6V6Ah battery •Power: The respirator is powered by the 6V6Ah lead-acid battery •Battery Charging: From mains by means of BP-6 battery charger (sold separately) •Battery Storage: The battery needs to be charged immediately after every use. Charge at least every three months even if not used •Battery life: > 8 hours •Charging time: < 8 hours •Airflow: > 170Lpm

K80E T8 (0313083) •Same model as 0313084 above but with ZA2P3 combined filters •Battery life: > 4 hours •Charging time: < 8 hours K80E T5 (0313161) •Helmet with T5 blower unit, one ZP3 HEPA filter, one rechargeable 6V6Ah battery, one battery charger •Power: The respirator is powered by the 6V6Ah lead-acid battery •Power, battery charging, battery storage and airflow as per above models •Battery life: > 8 hours •Charging time: < 8 hours

Kompat 88 – Gases and Industrial Dusts

• Self-contained helmet for easy mobility. • Ideal for dust and asbestos and shotcrete work

in mines, buildings and bridges. • The Kompat 88 respirator works by means of

slight over pressure which is created inside the helmet by a flow of filtered air.

• Air is drawn through two filters by means of two built-in blower units powered by rechargeable batteries.

• The helmet has batteries, blower / fan unit and filters all built into the helmet. This gives the wearer complete freedom of movement when in use.

STANDARD FEATURES

• Built in blower units and battery

• No cords, belts or breathing tubes required

• CE certified, Italian design

• Wide view fixed visor

• Complete protection of the head, face, ears, neck and respiratory system

• Real positive pressure makes breathing comfortable even under strain

• Fits most head sizes and accommodates beards and eye-wear

• Not affected by temperature changes and ultra violet rays

• Uniform airflow distribution

• Compact, heavy duty blower units

• Battery charger with microprocessor controlled charging functions

• High efficiency, long life filters

TECHNICAL INFORMATION

• Helmet Material Fibre Glass

• Colour White

• Visor Fixed polycarbonate

• Size Adj. 53-63cm

• Noise Level < 75dB

• Accessories Blower units & batteries built-in

• Battery 9 Ni-Cad

• Battery Life > 4 hours

• Charging Time < 4 hours

• Airflow > 170Lpm

concrete equipment catalogue

Documents

concrete pressure psi

rough concrete mixes

foundations pressure

pressure grouting

main hydraulic pump

gunite pumps

pumps versatility

grout mixers pumps