desmontar fat
TRANSCRIPT
-
8/13/2019 Desmontar FAT
1/19
-
8/13/2019 Desmontar FAT
2/19
15/02/13 Disassembling the Xbox 360 - Team Xecuter
team-xecuter.com/forums/showthread.php?t=61653 2/25
1.The first step is to remove the front face plate. Take a look at
the front of the Xbox 360 and insert your finger into the gap on the
side cover that is closest to the front USB ports [Pic 1a]. Gently
pull out the face plate with your thumb [Pic 1b]. With not much
force, the face plate should pop right off [Pic 1c].
[Pic 1a]
[Pic 1b]
-
8/13/2019 Desmontar FAT
3/19
15/02/13 Disassembling the Xbox 360 - Team Xecuter
team-xecuter.com/forums/showthread.php?t=61653 3/25
[Pic 1c]
2. You will notice that the gray ventilation side plates attach toboth the bottom and top white chassis. We will now remove the
gray side plate starting with the right side of the unit (The side
where the hard drive plugs into). For this you will need the
Xecuter Unlock Tool. First you need to unlatch the two internal
locks which is done quite easily [Pic 2a]& [Pic 2b]
-
8/13/2019 Desmontar FAT
4/19
15/02/13 Disassembling the Xbox 360 - Team Xecuter
team-xecuter.com/forums/showthread.php?t=61653 4/25
[Pic 2a]
[Pic 2b]
3. Here is a couple of pics showing the process of unlocking the
two internal latches [Pic 2c]. Note that when you unlock the latch
you should gently lift the gray panel [Pic 2d]
-
8/13/2019 Desmontar FAT
5/19
15/02/13 Disassembling the Xbox 360 - Team Xecuter
team-xecuter.com/forums/showthread.php?t=61653 5/25
[Pic 2c]
[Pic 2d]
4. There are three latches down each side of the case. These can
be accessed through the round air vent holes. Use the unlock
tool to push in these latches. On each latch gently lift the gray
side panel so that the latches cannot fall back into place [Pic
3a], [Pic 3b]& [Pic 3c].
[Pic 3a]
-
8/13/2019 Desmontar FAT
6/19
15/02/13 Disassembling the Xbox 360 - Team Xecuter
team-xecuter.com/forums/showthread.php?t=61653 6/25
[Pic 3b]
[Pic 3c]
5. Now turn the Xbox around as you will be doing the same to the
other side. To access the first hole to your left you will need to
remove a small gray rubber pad [Pic 3d].
[Pic 3d]
6. Now use the unlock tool again to push in two more latches
through the air vent holes. Remember to gently lift as you go
along [Pic 3e]& [Pic 3f].
-
8/13/2019 Desmontar FAT
7/19
15/02/13 Disassembling the Xbox 360 - Team Xecuter
team-xecuter.com/forums/showthread.php?t=61653 7/25
[Pic 3e]
[Pic 3f]
7. Remove the gray side panel from the case [Pic 3g].
[Pic 3g]
8. Now lets remove the gray panel on the other side of the case.
This one is a little more straight forward as there are no internallatches to unclip. There are three latches each side. Again use
the unlock tool to access each latch through the air vent holes.
Make sure you gently lift the gray side plate after unclipping each
latch[Pic 4a], [Pic 4b] &[Pic 4c]
-
8/13/2019 Desmontar FAT
8/19
15/02/13 Disassembling the Xbox 360 - Team Xecuter
team-xecuter.com/forums/showthread.php?t=61653 8/25
[Pic 4a]
[Pic 4b]
[Pic 4c]
8. Now lets switch to the other side. Again there are three
latches to unclip. Remember to gently lift the panel so the
latches do not fall back into place [Pic 5a], [Pic 5b] &[Pic 5c]
Pic 5a
-
8/13/2019 Desmontar FAT
9/19
15/02/13 Disassembling the Xbox 360 - Team Xecuter
team-xecuter.com/forums/showthread.php?t=61653 9/25
[Pic 5b]
[Pic 5c]
9. Once you have both side panels removed, you have essentially
removed the main locking mechanism that holds the top and
bottom shells together. You are now ready to split the case apart
[Pic 6a]
[Pic 6a]
10. Now turn over the console to remove the bottom shell. You
will need the Unlocking Tool as there are 5 small rectangle holes
to the left of the case [Pic 7a]and 2 small rectangle holes to the
right [Pic 7b].
-
8/13/2019 Desmontar FAT
10/19
15/02/13 Disassembling the Xbox 360 - Team Xecuter
team-xecuter.com/forums/showthread.php?t=61653 10/25
[Pic 7a]
[Pic 7b]
11. There are 5 pins on one side of the Unlock Tool [Pic 8a]and
2 pins on the other side [Pic 8b]. You will need to insert these
pins into the small rectangle holes to enable the case to unlatch.The reason the front of the bottom shell needs to be lifted is to
prevent the rear latches from reattaching themselves.
[Pic 8a]
-
8/13/2019 Desmontar FAT
11/19
15/02/13 Disassembling the Xbox 360 - Team Xecuter
team-xecuter.com/forums/showthread.php?t=61653 11/25
[Pic 8b]
12. Carefully insert the Unlock Tool into the row of 5 [Pic 8c]. You
should hear a click sound for each clamp you unlatch. Once
complete, lift up the left side of the case [Pic 8d]then move over
to the row of 2 on the other side of the case.
[Pic 8c]
[Pic 8d]
13. Carefully insert the Unlock Tool into the row of 2 [Pic 8e]. You
should hear a click sound for each clamp you unlatch.
-
8/13/2019 Desmontar FAT
12/19
15/02/13 Disassembling the Xbox 360 - Team Xecuter
team-xecuter.com/forums/showthread.php?t=61653 12/25
[Pic 8e]
14. Once complete, lift up the back and then start work on the
front of the Xbox [Pic 9a].
[Pic 9a]
15. Using a flat head screw driver or even your fingernail, gently
pry up the 4 clips holding the top shell to the bottom [Pic 10a].
You may want to be careful here if you wish to maintain the
quality of the security sticker. Some people use a hairdyer to
remove it so it can be replaced intact later. Once the clips are
unlatched [Pic 10b], you can now split the case apart completely
[Pic 10c].
-
8/13/2019 Desmontar FAT
13/19
15/02/13 Disassembling the Xbox 360 - Team Xecuter
team-xecuter.com/forums/showthread.php?t=61653 13/25
[Pic 10a]
[Pic 10b]
[Pic 10c]
16. Looking down on the Xbox metal casing you will notice that
there are a lot of screws. We are only interested in 6 of them.
Using your Torx 10 screw driver, remove the silver screws [Pic
11a].
-
8/13/2019 Desmontar FAT
14/19
15/02/13 Disassembling the Xbox 360 - Team Xecuter
team-xecuter.com/forums/showthread.php?t=61653 14/25
[Pic 11a]
17. Once you have all the screws removed, flip the Xbox 360 right
side up first remove the eject button and then lift up the top
plastic shell [Pic 12a] & [Pic 12b].
[Pic 12a]
-
8/13/2019 Desmontar FAT
15/19
15/02/13 Disassembling the Xbox 360 - Team Xecuter
team-xecuter.com/forums/showthread.php?t=61653 15/25
[Pic 12b]
18. You should now be greeted with the internals of the Xbox 360
[Pic 12c]. Congratulations! You are now ready to update your
DVD firmware or continue onto the next part of the tutorial which
is to take out the motherboard for RROD repairs.
[Pic 12c]
PART 2: Removing The Motherboard (For RROD Repairs
etc)
18. You first need to remove the front panel. Unclip the plastic
cover [Pic 13a]and unscrew the 3 screws [Pic 13b]using a Torx
8 screwdriver. Once the screws have been removed unplug the
circuit board from the Xbox [Pic 13c].
[Pic 13a]
-
8/13/2019 Desmontar FAT
16/19
15/02/13 Disassembling the Xbox 360 - Team Xecuter
team-xecuter.com/forums/showthread.php?t=61653 16/25
[Pic 13b]
[Pic 13c]
19. Now remove the DVD Drive (unplug the Power & Sata cable
from the back of the drive) and then remove the exhaust unit thatcovers the fan (if you have one installed) [Pic 14a]. Unplug the
fans power cable from the motherboard and unclip the fan from
the chassis and remove [Pic 14b & 14c].
[Pic 14a]
-
8/13/2019 Desmontar FAT
17/19
15/02/13 Disassembling the Xbox 360 - Team Xecuter
team-xecuter.com/forums/showthread.php?t=61653 17/25
[Pic 14b]
[Pic 14c]
20. Turn the case over and remove all the screws. The outer
screws are Torx 10 [Pic 15a]and the heatsink screws are Torx 8
[Pic 15b].
-
8/13/2019 Desmontar FAT
18/19
15/02/13 Disassembling the Xbox 360 - Team Xecuter
team-xecuter.com/forums/showthread.php?t=61653 18/25
[Pic 15a]
[Pic 15b]
21. You can now safely remove the motherboard from the chassis
[Pic 16]
-
8/13/2019 Desmontar FAT
19/19
15/02/13 Disassembling the Xbox 360 - Team Xecuter
[Pic 16]
PLEASE READ THISBEFOREPOSTING ON THESE FORUMS
COMPLETE GUIDE TO XBOXDVD, XBOX FIRMWARE &
XECUTER CK3 KIT - CLICK HERE
LT+ & AP25 FAQ - CLICK HERE
DGX FAQ & TROUBLESHOOTING- CLICK HERE
Xecuter- XBOX 360 Setup
Model:Xbox 360 Prem ium, Xbox 360 Elite
DVD:Hitachi, Samsung, Benq, Liteon, Unknown
Motherboard:Xenon, Zephyr, Falcon, Opus, Jasper,
Unknown
SATA Chipset:X360USB PRO
Click here to enter your Xbox setup details
The Following 18 Users Say
Thank You to Xecuter For This
Useful Post:
A74star(24th September 11), afiser(13th November 11),
alistairmark(5th December 11), Br00K(5th July 11), cunny(13th
January 12), Games Goblin(2nd January 12), gilsport(16th
November 11), haznpapo(16th April 11), Jonas225(19th February
11), Legendnever(13th October 11), ll4sheezy(23rd November 11),
patupo(10th June 12), Ramsay2011(19th March 11),
SAMMY816(19th April 11), taximan250(15th April 11), testfall(13th
January 12), X-R4Y(6th June 11), zangooo(24th June 11)
17th November 09 #2
http://team-xecuter.com/forums/showpost.php?p=337812&postcount=2http://team-xecuter.com/forums/member.php?u=188041http://team-xecuter.com/forums/member.php?u=176608http://team-xecuter.com/forums/member.php?u=207545http://team-xecuter.com/forums/member.php?u=185442http://team-xecuter.com/forums/member.php?u=187085http://team-xecuter.com/forums/member.php?u=184780http://team-xecuter.com/forums/member.php?u=213813http://team-xecuter.com/forums/member.php?u=169177http://team-xecuter.com/forums/member.php?u=195371http://team-xecuter.com/forums/member.php?u=177631http://team-xecuter.com/forums/member.php?u=186588http://team-xecuter.com/forums/member.php?u=196507http://team-xecuter.com/forums/member.php?u=172722http://team-xecuter.com/forums/member.php?u=150026http://team-xecuter.com/forums/member.php?u=190877http://team-xecuter.com/forums/member.php?u=199450http://team-xecuter.com/forums/member.php?u=105115http://team-xecuter.com/forums/member.php?u=194125http://team-xecuter.com/forums/newreply.php?do=newreply&p=337811http://www.team-xecuter.com/forums/profile.php?do=editprofilehttp://team-xecuter.com/forums/showthread.php?t=97128http://www.team-xecuter.com/forums/showthread.php?t=58387http://www.team-xecuter.com/forums/showthread.php?t=52147http://www.team-xecuter.com/forums/showthread.php?t=52153