detection analysis location - sekotechsekotech.com/files/sekotech-2014-04-tscm-catalog.pdf ·...

Detection Analysis Location

Radio Frequency (RF) Detectors

Multi Functional Counter Surveillance Equipment

Radio Monitoring and Signal Analysis

Non-linear Junction Detectors (NLJD)

Explosives Detectors

WWW.SEKOTECH.COM

SEKOTECHTechnicalSurveillanceCounterMeasures

Dimensions (transportation):

Height 57 cm

Width 22 cm

Thickness 12 cm

Weight 1.5 Kg

LornetNON LINEAR JUNCTION DETECTOR

Main features:

• Small dimensions and weight of the device

• Easy-to-use

• Automatic and manual modes of power change of the probing signal

• Use of the latest technologies and materials, ergonomic

• High detection potential

• Use of wireless earphones

A non-linear junction detector Lornet is designed to detect various kinds of electronic devices containing semiconductor elements, such as microphone amplifiers, audio-recorders, eavesdropping and other remotely controlled devices; both in switched-on and switched-off modes.

Delivery set:1. Lornet device with Li-Ion battery2. Wireless accessories (a receiver with earphones)3. Power adapter-charger (110-240V)4. Transportation bag

Technical specifications:

Type of a probing signal pulse CW

Probing signal frequency 890 - 891 MHz

Probing signal power pulse - 15 W CW - 1 W

Sensitivity not worse -120 dBm

Dynamic range more than 80 dB

Power supply Rechargeable battery

Operation time over 3,5 h (at pulse probing signal) over 1,5 h (at CW probing signal)

Dimensions (in operation):

Height 100 cm

Width 15 cm

Thickness 4 cm

Weight 1 Kg


Type of a probing signal pulse CW

Probing signal frequency 2.4 - 2.483 GHz

Probing signal power pulse - 10 W CW - 1 W




Operation time over 3h (at pulse probing signal) over 1,5h (at CW probing signal)

Dimensions (in operation):

Height 39 cm

Width 10 cm

Thickness 4 cm

Weight 700 g

Dimensions (transportation):

Height 23 cm

Width 10 cm

Thickness 5.5 cm

Weight 1500 g

Lornet-24NON LINEAR JUNCTION DETECTOR

Main features:

• It is a unique device worldwide by its frequency, weight and dimension characteristics.

• Easy-to-use.

• All operation modes of Lornet device are available (automatic and manual modes of power change of the probing signal in a pulse mode, manual power change in CW mode).

• Use of the latest technologies and materials, ergonomic.

• Electromagnetic effect on operator (during operation) is significantly lower than the one of cell phone.

• High detection potential (in some cases due to a higher frequency of probing signal it is more efficient than detectors using more power, but operating in a standard range).

• Wireless earphones.

• It is possible to operate in hard-to-reach places and under conditions of limited space (antenna thickness does not exceed 18 mm).

A non-linear junction detector Lornet-24 is used for conducting a strategic and search work afield, in premises, transport, and is designed to find specific equipment containing semiconductor components.

An automatic system of frequency selection is integrated into the device, and it can tune away from a narrowband interference automatically (by a criterion of minimum noise of the receiving channel of the 2nd harmonic).

Delivery set:1. Lornet-24 device with Li-Ion battery2. Wireless accessories (a receiver with earphones)3. Power adapter-charger (110-240V)4. Transportation bag


Type of a probing signal pulse

Probing signal frequency 3.5 - 3.620 GHz

Probing signal power pulse - 20 W

Detection ranger 1-10 m or more


Dynamic range not lesss than 40 dB


Operation time up to 3h (at pulse probing signal) Dimensions:

Height 47,7 cm

Width 30,3 cm

Thickness 22,7 cm

Weight 1.2 Kg

Main features:

• 3.6 GHz high frequency of probing signal outside of GSM band.

• Long detection range 1-10 m or more.

• Narrow diagram of antenna directivity.

• Laser pointer to pinpoint inspected area.

• Easy-to-use, ergonomic.

• Automatic and manual adjustment of probing signal power.

• Electromagnetic effect on operator (during operation) is very low.


It is very efficient when it comes to identifying of

miniaturized electronic devices (10x20mm) at a

considerable distance, which is sometimes crucial.

For instance, a suspicious object has to be analyzed within

a safe distance.

Moreover, the use of a super high signal frequency range

gives Lornet-36 some unique capabilities to detect

semiconductors covered by various materials.

It can also detect devices through slits and holes,

ungrounded shielding, etc.


A non-linear junction detector Lornet-36 is an

indispensable tool for a quick and reliable location of

unauthorized electronic devices during investigation

operations in premises with a high density of electronic

equipment.

NON LINEAR JUNCTION DETECTOR

Lornet-36


Type of a probing signal pulse

Probing signal frequency1st probing signal 2nd probing signal

789,5-791,5 MHz;3581,5-3607,5 MHz

Transmitter peak power in each frequency range 40W / 20W

Duty cycle 0,3% and 5%

Detection ranger 1-10 m or more

Sensitivity -110 dBm


Operation time 0.3% duty cycle 0.5% duty cycle

not less than 3 h 1.5 h

Dimensions:

Height 30,5 cm

Width 30,5 cm

Thickness 22,7 cm

Weight 1.6 Kg

Main features:

• The first non-linear detector which combines the advantages of a microwave detector and the detector of traditional range with the weight less than 1 kg and possibility to indicate the results in both ranges simultaneously.

• Long detection range 1-10 m or more.

• Laser pinpointing for a space selective object localization.

• Easy-to-use, ergonomic.

• Automatic and manual adjustment of probing signal power.

• Electromagnetic effect on operator (during operation) is very low.


Lornet-0836 is an indispensable tool for a quick and

reliable detection of devices containing semiconductor

components. It can be used for counter-surveillance

investigation works in premises (covert transmitters

identification), as well as for location of explosive devices

outdoor. The DPF (double probing frequency) technology

with a patent pending antenna system places it beyond

comparison to other rivals.

Unique opportunity to detect semiconductor

elements hidden by different materials (detection

through cracks, unearthed shielding, reflections from

smooth surfaces, SIM card is detected at the distance

of 80 cm, etc.)


Lornet-0836NON LINEAR JUNCTION DETECTOR

NR-μNON LINEAR JUNCTION DETECTOR

Main features:

• various electronic units detection in any operational mode: active, switched off and stand-by

• light portable design with built-in connecting cables (from antenna to the main unit), optional display on the back of antenna unit cover

• original circuit design for optimum combination of pulse & CW NLJD merits

• extended continuous operational time (without battery replacement)

• spare, replaceable battery

Detection of covert eavesdropping

electronics (radio microphones, microphone

amplifiers, dictaphones and etc.) in premises.

Examination of office and living premises

structures as well as furniture and domestic

articles for concealed bugging facilities.

Delivery set:1. NR-μ device with Li-Ion battery2. Power adapter-charger (110-240V)3. Spare battery4. Transportation bag


Antenna, polarization directional, circular


Probing signal power searching envelope separation (20K)

0.4 W 2 W

Receiver sensitivity (under 10dB signal/noise ratio)

not worse than -150 dBW (-120dBm)



Operation time not less than 4 h

Dimensions:

Height 100 cm

Width 15 cm

Thickness 4 cm

Weight 2.9 Kg

NR-900 EK EagleNON LINEAR JUNCTION DETECTOR

NR-900 EK application possibilities:

• roads, terrain and objects inspection for mines,

improvised explosive devices (IED) and other

explosive appliances with electronic components;

• searching for weapons caches, ammunition,

explosive devices and communication facilities;

• investigation of suspicious items, searching of

destructive and terrorist devices.

Main features:

• extended detection range;

• equipment design allows its usage in tactical airborne missions;

• efficient use in search/reconnaissance missions;

• high searching speed;

• safe to handle, user-friendly design;

• extended continuous operational time without battery replacement;

• long-term operation in field conditions.

NR-900 EK is designed for detection of mines and explosive devices with

electronic fuses (activation system) concealed on the ground surface,

beneath the surface (snow), under the road pavement and in various

facilities.

NR-900 EK Detects:• communicational transmitters & receivers as well as alarm and

remote control system facilities;• electronic and electromechanical timers;• acoustic, magnetic, optoelectronic sensors and midget TV cameras;• built-in metal-ware as well as hidden machinery and appliances;• domestic electronic units and alpine skiing equipment in snow traps

during rescue operations.

Delivery set:1. NR-900EK device with battery2. Power adapter-charger (110-240V)3. Spare battery4. Transportation bag


Probing signal type pulse


Receiver 2-channel (2nd and 3rd harmonics)

Probing signal power average peak

0,15 W 200 W


Power supply Ni-Cad battery, 6V/7Ah

Audio output headphones

User interface LED display

Start-up time less than 5 min

Operation time not less than 8 h

Operating temperature -30º C…+50º C

Weight (ready for operation /transportation package) 5.1 Kg / 12.0 Kg


Type of a probing signal pulse and continuous

Probing signal frequency 2.4 GHz

Probing signal power 0.5 W

Receiver sensitivity -150 dB/W

Detection ranger 10 cm - 1 m

Dynamic Range 80 dB

Power supply Internal Li-Ion rechargeable battery

Operation time pulse modecontinuous

not less than 2.5 h 2 h

Charging time 2 hours

Working temperature from -100 C to + 400 C

Buclet-2NON LINEAR JUNCTION DETECTOR

Main features:

• Compact and easy to use.

• 2.4 GHz probing signal.

• Automatic selection of operating

channel having minimum noise level.

Buclet-2 is ideal for use in correctional

facilities to inspect packages or inmate cells

for presence of forbidden objects.

As other non-linear junction detectors Buclet-2 detects all

electronic equipment having semiconductor elements in

active and passive (switched-off) modes.

Buclet-2 is designed to perform inspection of packages,

difficult to access places. It is also compact and easy to

operate for inexperienced user as it has minimum set of

functions and indication of only 2nd harmonics.

Delivery set:1. Buclet-2 non-linear junction detector2. Headphones3. Power adapter-charger (220V)4. Packing box

Dimensions:

Height 220 mm

Width 90 mm

Thickness 90 mm

Weight 350 g

Raksa iDetRF Detector

RAKSA iDet detects:

• Cellular phones of GSM900/1800,

UMTS(3G), CDMA 450 (453-458 MHz)

• Cordless DECT phones

• Bluetooth and Wi-Fi devices

• Wireless video cameras

• Radio transmitters with analog

modulation (AM, FM, PM)

• Radio transmitters with digital

modulation and continuous carrier (FSK,

PSK, etc.)

• Radio transmitters with wideband

modulation up to 10 MHz bandwidth

Main features:

• Selective reception of radio signals

• High speed of scanning and analyzing

• Detection of wideband and digital

signals

• Adaptation to the background noise in

Guard Mode

• Difference search mode

• Audio monitoring

• Signal frequency and level measurement

• Alarm events log

• Discrete alarm (vibration mode)

• No need of external antenna

RAKSA iDet – a selective RF Detector which can be used

to detect and locate in a near field a wide variety of radio

transmitters used for a secret access to information or its

leakage.

RAKSA iDet is a super heterodyne receiver with a low

IF and frequency synthesizer. Scanning and analyzing

cycle period is 1.0-1.5 sec. The device can operate within

guard, sweep, search, deviation measure modes and

monitoring of digital signals.

Delivery set:1. Raksa Idet2. Power adapter-charger (110-240V)3. Packing box


Frequency band 50 - 3300 МHz

Typical sensitivity 70 mV/m

Dynamic range 50 dB

Period of full scanning cycle ≤ 1.5 s

Power supply Ni-Cad battery, 6V/7Ah

Running time in guard mode 4 - 12 h

Running time in other modes 3 hours

OLED display 128 x 64

Dimensions 77 х 43 х 18 mm

Weight 35 g

ST-110RF Detector

ST 110 Detects:

• Radio-microphones (BUGs) ;

• telephone radio retransmitter (TAP);

• wireless stethoscope;

• Video-cameras with radio channel for data transfer;

• Radio beacons for people, vehicles or cargos tracking systems;

• Mobile phones and radio modems of GSM, DECT standards;

• Data transmission devices of BLUETOOTH and WLAN standards.

• Principle of operation of ST 110 is based on broadband detection of

electrical field

Search mode:This mode is intended to search and detect RD location. Visual indication of signal level on 32-seg. scale.GSM, DECT, BLUETOOTH, WLAN detection

Oscilloscope mode:Oscilloscope mode allows operator to view oscillogram of selected signal

Log view mode:This mode is intended to view the log of events resulting from the unit running in MONITORING mode. The classification of the events by time, duration or signal level is provided.

PC Software allows: time graphic display of data and the results of operation of the ST 110 ;ST 110 remote full control using PC;extended settings assignment for MONITORING mode; load and display textual and graphical information of the operation of the ST 110 in MONITORING mode (Event Log); Firmware updating

Monitoring mode:This mode is designed for independent operation of ST110 on preset conditions. The information about detected signals is saved by means of non-volatile memory of the device (9 banks, each for 999 events). Scheduled work operation is also provided.

ST 110 is designed for detection and localization of radio-wave radiation devices

(RD) that are designed or used for unauthorized data transfer via radio channel.


Frequency band 50-2500 МHz

Threshold sensitivity, dBm-75 (50 MHz)-70 (1500 MHz)-50 (2500 MHz)

Dynamic Range of indication, dB 55 (50-2000 MHz)40 (2000-2500 MHz)

Sensitivity of frequency meter , dBm-35 (50 МHz)-50 (500 МHz)-20 (2500 МHz)

Frequency measurements accuracy, % 0.005

Cut-off frequency of LPF, MHz 750

SHF antenna-detector ST110.SHF

Frequency range , MHz 2000-7000

Threshold sensitivity, W/cm2 2x10-10

Dynamic Range , dB 45

Power supply Li Pol 3.6V

Consumption current, mА 65

Indication Color OLED Display 160X128

Dimension main block (with-out antenna), mm 90x54x21

ST-165CELLULAR COMMUNICATIONS SIGNAL DETECTOR

Automatic mode:This mode is intended for DRTD automatic detection when it exceeds the operation threshold set by user. Signal data are logged. Scheduled work is provided.

Manual mode:This mode is intended to detect:• location of signal source;• threshold levels value for later use in AUTOMATIC MODE.

Indication of BASE STATION signals level is provided in this mode

Additional possibilities:• Adjustment on “local” country frequencies of standard UMTC• Built-in Relay (terminals on the external port) extends the

functionality of the ST 165 to remotely control jammers and additional indicators.

PC Software allows: • time graphic display of data and the results of operation of the ST 165 ;• ST 165 remote full control using PC;• Firmware update.

Log view mode:This MODE is designed for viewing the log of events. Time of event, its duration, type of event, signal strength are displayed.

ST 165 is designed for detection and identification of mobile radio

transmitters of cellular communications standards (mobile phones

and modems of GSM 900, 1800, UMTS), wireless data transmission

(WI FI and BLUETOOTH) and cordless phones (DECT). Additionally

indication of base stations power signal strength and data exchange

intensity is provided. All mentioned above will be referred to as Digital

Radio Transmitting Devices (DRTD)

ST 165 operates on the basis of direct-conversion receiver. To detect signals,

the ST 165 scans a series of frequency ranges of the known transmission

standards. The user can set up the detection threshold and the number of

desired frequency bands. Signals identification is performed on basis of

analysis of detected signals time parameters.

Delivery set:1. ST-165 device2. Power adapter-charger (110-240V)3. PC Software4. Packing box


Frequency ranges, MHz

890-9601710-19001940-21442400-2600430-465 (with ST165.CDMA version)

Level ranges of displayed signal, dB

890-960 MHz2400-2600MHz1940-2144MHz1710-1900MHz

-75 – +10-70 – +10-80 – +10-70 – +10

Alarm level setting range, dB 60

The weakening out of band signals, not worse, dB 50

Power supply Li Pol 3.6V

Consumption current, mА 300

Indication Color OLED Display 160X128

Dimension main block (with-out antenna), mm 90x54x21

ST-131 Piranha II (page 1 of 3)

MULTIFUNCTION TSCM DEVICE

Operating modes:

• RF detector frequency meter

30 – 4400 MHz

• Digital signal level indication mode:

CDMA, GSM900, GSM1800, DECT,

3G, 2.4 GHz, 4G LTE

• Differential spectrum mode

• Oscilloscope

• Signal demodulation

• UHF detector 4000-18000 MHz

• Wire line scanner

• Wire line non-linear junction

detector

(only in ST-131N Piranha II)

• Optical IR channel

• Acoustoelectric channel

• Magnetic channel

The main types of the STM, for detection of which

ST131 is intended, include the following:

• The STM with transfer of information by radio channel.

Such devices include first of all:

• Radio microphones including devices with storage and

subsequent transfer of information (burst transmitter) and

Frequency Hopping Spread Spectrum (FHSS);

• Telephone radio broadcasting devices.

• Radio stethoscopes.

• Wireless video cameras.

• Mobile telephones and modems of CDMA, GSM, UMTS,

DECT standards used without authorization.

• Devices using digital channels of data transmission of

WLAN and BLUETOOTH standards.

• Radio beacons for object movement tracking.

• The STM that use AC power, telephone, security and fire

alarm lines for information transfer.

• The STM characterized by information transmission in

infra-red range.

• The STM characterized by transmission of information in

ultrasonic frequency range.

Multifunction detection device ST131 PIRANHA-II is designed for detection and localization of special technical means (STM) used for surreptitious obtaining of information, as well as identification of natural and artificial sources of information leakage.



Basic set:1. Main unit 2. UHF converter (ST131.UHF) 3. Broadband UHF antenna (ST131.UHF.A) 4. Wire line adapter (ST131.AWL) 5. Leads 6. Main unit supporting block 7. Main unit shoulder holder 8. Headphones 9. Tripod 10. Power supply unit - 2 pcs 11. AA batteries - 8 pcs12. Mini-disc with software 13. User manual

Supplementary set1. SHF DETECTOR ST131.SHF2. IR probe ST131.IR3. Magnetic field probe ST131.MF4. Control unit ST131.TEST

ST-131 Piranha ii - technical specifications:

Digital signal processing module

Simultaneous processing frequency range, MHz 0.01-30

Resolution ADC, bit 10, 14 and 16

Number of FFT points 32768 (PC mode) 512 (main unit)

Filters sizes, MHz 0.01-6.8 МHz

Demodulation types АМ, FM, SSB, TV (АМ)

Radio channel - UHF converter

Frequency range, MHz 30-4100

Displayed noise level Within the whole bandwidth, dBm Within DDC bandwidth 1 kHz, dBm

-90 main unit (-110 PC mode)- 110

Input signal maximal level, dBm 5

Sweep speed, GHz/sec, at least 10

Value of DDC bandwidth, MHz1024, 512, 224, 112, 54, 28, 6.8, 2.5, 0.63, 0.15, 0.075, 0.04, 0.001 и 0.0005

Identified data transfer standards CDMA, GSM, 3G,4G, WLAN, BLUETOOTH, DECT

Radio channel - SHF Detector ST131.SHF

Frequency range, MHz 4000-18000

Threshold sensitivity, W/cm2 -65

Antenna beamwidth, degrees 60-90

“WIRE LINE” Channel

Frequency range 1, MHz 0.01-30

Frequency range, 2, KHz 0.3 - 15

OPTICAL Channel

Dynamic range, dB 60

Frequency range, MHz 0.01-30

“ACOUSTOELECTRIC” Channel

Frequency range, KHz 0.01-125

input signal maximal level, dBm -5

Gain input amplifier 6, 14,20, 26, 34 40

Non-linear junction detector

Frequency of test signal, kHz 150-220

Main unit

Dimensions, mm 190x97x50

Indication 3.5” 240x320, TFT 262144 colors

Interface USB 2.0, 200 Mbit/s

Power supply 6 AA batteries (rechargeable batteries)

Only for ST-131N Piranha II:



Special software “ST131 ANALYZER-PRO” highly extends capacities of ST131 for analysis and processing of signals.

This software implemented the following functions:

• Spectral OSCILLOGRAPH and vector analysis

• “waterfall”

• Creation of signals data base

• MONITORING with expanded presets

• Streaming recording of signals to HDD of PC

Sirius (page 1 of 3)

WIRE LINES ANALYSER

The SIRIUS (4rd generation) is designed for detection of unauthorized galvanic connections, detection and analysis of signals in wire circuits and connected electronic devices, which appear as a result of acoustoelectric conversion or forming of modulation in return high frequency signal.

The SIRIUS provides the following possibilities to an operator:• Analysis of HF signals spectra.• Analysis of audio frequencies.• Injection of HF signals to wire circuits and data

processing equipment and analysis of converted signals.

• Impulse reflectometry.• Complex electrical measurements (mode of

digital multimeter, transient curve, volt-ampere curve, frequency-response characteristic, gain-phase characteristic, load-voltage characteristic).

• Extended possibilities for examination of wire

circuits.

• Wide frequency range of examined signals.

• Vector spectral analysis of signals using

different intermediate pass bands.

• High dynamic range of processed signals

amplitudes.

• High processing speed of input signals

resultant spectra.• Measurement of AC and DC voltage,

impedance, capacitance and inductance.• Demodulation of AM and FM signals in real

time.• Automatic compensation of injected signal

phase shifts in the mode of acoustically induced modulation in high frequency signal.

• Several automatic analysis modes.• Splashproof and shockproof case.

Distinctive features:

Signal Lines Commutator: 220 V, Telphone, LAN

Priboi (optional): Active acoustic system for generation of various tonal and noise signals

Parametric Microphone Imitator

Delivery set:1. Main unit2. Set of connection cables and adapters3. PRIBOI active acoustic system (optional)4. Simulator of parametric microphone5. Signal switcher6. Headphones7. UP-8 wire tracer


WIRE LINES ANALYSER

DETECTION OF EFFECT OF ACOUSTICALLY INDUCED MODULATION IN HF SIGNAL

Frequency range of excitation signal, kHz 10~400000

Root-mean-square voltage of excitation signal at LINE jack, V 1

Attenuation range of excitation signal level, not less than, dB 40

Detection of modulating signals with modulation factor (at SNR 10 dB), not more than 10-4

Pass bands for modulating signal, kHz 5; 25

Minimal step of excitation signal frequency tuning (for pass band of 5 kHz), Hz 100

Frequency resolution (for pass band of 5 kHz), Hz 10

Phase shift compensation between excitation signal and response signal, grad 0 ~180, with step of 1

Setting range of bias voltage, V ±15, with step of 1

Detected modulation formats AM, FM, PM

Frequency setting of test acoustic signal, Hz 63~11300, with step of 1

Acoustic signal amplitude at TONE jack output, mV 5, 100, 250, 500, 1000

Output impedance at TONE jack, Ω 620

...continued

ANALYSIS OF INPUT SIGNAL SPECTRUM

Input signal frequency range, kHz 10 ~ 400000

Dynamic range of input signal processing, not less than, dB 140

Sensitivity at input (SNR 10 dB) no more than, dBW/Hz -170

Maximum amplitude of input signal, V 10

Electronic attenuator of input signal, dB 20

Input impedance at LINE jack output, Ω 50

Setting range of bias voltage, V ±15, with step of 1

Number of processed dots in single capture 1024

Pass bands for converted signal (at -3dB level), kHz 5; 25; 250; 2500; 25000

Frequency resolution (for different pass bands, 5 kHz~25 MHz), kHz 0.01; 0.06; 0.6; 6; 60

Time of forming of single spectrum capture, no more than, s 0.05

Scanning time of 10~400000 kHz frequency range (at 25 MHz pass band), no more than, s 1

GENERAL SPECIFICATIONS OF MAIN UNIT

AC power supply voltage, V 100~240

Consumption power, not more than, W 100

Main unit dimensions, mm 474 x 415 x 149

Main unit weight, kg 12


WIRE LINES ANALYSER

...continued

ANALYSIS OF SOUND FREQUENCIES

Input signal frequency range, Hz 100 ~100000

Pass bands of input signal (at 3 dB level), kHz 25; 100

Dynamic range of input signal processing (taking into account input attenuator), not less than, dB 140

Sensitivity at input (at REMOTE jack, 25 kHz pass band, SNR 10 dB) no more than, µV 1

Frequency resolution for 25 kHz and 100 kHz pass bands, Hz 60; 240

Maximum amplitude of input signal (with input attenuator), V 20

Electronic attenuator of input signal, dB 20

AGC setting range, dB 40

Voltage bias setting range, V ±15, with step of 1

Input impedance at REMOTE jack, Ω 620

Input impedance when using Signal Switcher, kΩ 50

IMPULSE REFLECTOMETRY

Maximum probing distance (at Kv=1.5), m 0~6400

Probing distances (at Kv=1.5), m 50;100;200;400;800; 1600;3200;6400

Duration of probing impulses, ns 5;10;20;50;100;200; 500;1000

Averaging of measured values (number of probing impulses per measurement) 1;2;5;10;20;50;100; 200

Amplitude of probing impulses, V 5

Output impedance, Ω 50

Overlapped attenuation,dB 80

Distance measurement error, not more than, % 0.2

Setting range of shortening coefficient (Kv) 1.0~3.0 with step of 0.01

x-shift (for Kv=1.5), m 0~6400

MEASUREMENT OF WIRE CIRCUITS PARAMETERS

DC voltage, V 0.001~100

AC voltage, V 0.001~100

Voltage of low frequency current, V 0.01~1

Voltage of high frequency current, V 0.01~1

Impedance, Ω 10-1~108

Capacitance, F 10-12~10-4

Inductance, H 10-3~102

Priboi (Acoustic System for Sirius)

SIRIUS ACCESSORIES

Characteristics of the device allow using it as part of instrumentation systems. The PRIBOI can be employed as a standalone device as well as in conjunction with the SIRIUS.

The PRIBOI is a loudspeaker with a built-in generator, placed on the speaker backside. There are jacks for connecting power and input signal cables. Volume control is on the front side of the loudspeaker.

Loudspeaker housing and generator are electromagnetically shielded.

THE DEVICE GENERATES AND RADIATES ACOUSTIC SIGNALS:

When operating with the built-in generator:• Tonal signal with 1000 Hz frequency;• White noise in 125 - 8000 Hz frequency band.

When operating with an external generator:• Tonal and noise signals in 20 Hz -20 kHz frequency band.

THE DEVICE PROVIDES SOUND PRESSURE:• 94 dB in white noise band;• 104 dB on 1 kHz frequency.• The PRIBOI is powered by the mains (220 ± 10 V).

The PRIBOI active acoustic system for Syrius is designed for generation of various tonal and noise signals, required for:

• Testing and measuring parameters of audio- and vibro-isolating properties of rooms, constructions and engineering services;

• Testing effectiveness of acoustic and vibroacoustic noise masking;

• Special examinations of main and auxiliary information processing equipment;

• Evaluation of acoustic and vibroacoustic signals characteristics with octave and third-octave analysis;

• Certification of protected premises.

Kassandra-21K (page 1 of 3)

RADIO MONITORING AND SIGNAL ANALYSIS

Unique combination of innovative solutions and advanced RadioInspector softwareExtended bandwidth of up to 21,000 MHz. Radio monitoring without VHF converters.Maximum scanning rate over 2,000 MHz/s within 20 kHz monitoring bandwidth. Dynamic range over 113 dB.Spectrum purity of internal tuners in HF and VHF bandwidth. No damaged frequencies and internal moire components.Automated radio emission classification and function of analysing digital communication standards.

Remote control via shared LAN or WAN.

RInspectorRT software features:

• easily adaptable user interface with unique functions and broad settings.

• task packages generated for scanning within the operating bandwidth can include any number of serially processed tasks, each with its own parameters assigned;

• panorama of current, maximum, minimum and averaged values of received signals;

• spectral pattern – 2D or 3D time-distributed panorama without any recording time limitations;

• marker and cursor measurements;

• saving and delayed analysis functions; any saved task can be re-run and further recorded into the

panorama data base;

• function of saving the reference panorama and panorama benchmarking analysis;

• diverted reception technique using an antenna switch;

• adjustable threshold line; adjustable and dynamic threshold;

• list of signals exceeding the threshold;

• frequency assignment data base and associated processing tools including a tailored calculator;

• HF spectrum analyser for real-time analysis of individual signals;



...continued

• LF analysis – oscilloscope, low-frequency spectrum analyser, octave analyser, audio recording including

5-second information section before the recording, analysis and editing of saved data;

• automated response to detection: audio signal recording, signal analysis, in particular, for belonging

to analogue TV signals;

• additional analysis of detected signals (numeric and graphic);

• generation of reports on analysed frequency bandwidths and detected signals; export into Microsoft

Word®, Microsoft Excel®, text and graphic files;

• additional receiver control for independent low-frequency analysis.

• 4-link HF switch (up to 6 GHz);

• additional low-frequency input (up to 30 MHz), VHF antenna included in the delivery package;

• user-friendly interface, user-defined window settings, help, prompt messages

• one-click scalable spectral panorama;

• scalable and scrollable 2D and 3D spectral pattern (waterfall);

• adjustable threshold

• list of detected signals with statistics viewer;

• up to 8 MHz real-time spectrum analyser without any time limitations;

• automated processing of detected signals;

• control panel for an additional receiver;

• low-frequency oscilloscope, spectrum analyser, octave analyser;

• IQ data and demodulated AM and FM signal recording;

• frequency assignment data base and a tailored calculator;

• functional scalability by adding extra options.

Optional software modules extend analysing capabilities of RInspectorRT:

• RInspectorWiFi software detects Wi-Fi equipment and analyses Wi-Fi networks.

• D-Test option allows:

- Automated identification and analysis of

DECT, TETRA, GSM, Bluetooth, DMR, APCO25, DRM, DVB; - Analysis of GSM, DECT and Bluetooth network topology;

- Demodulation of APCO25, DMR(MOTOTRBO), DRM;- Display of PAL/SECAM/NTSC TV;- Digital signal analysis (vector diagram, filtration, decimation

and digital signal shift in vectors (I/Q)).

• RInspectorRP – specialised software for post analysis of recorded data on independed PC;




Radio frequency parametersLW inputSwitched HF inputs (4)VHF input

0.009 - 30 MHz24 – 6,000 MHz6,000 – 21,000 MHz

Sensitivity Minus 144 dBm/Hz

Dynamic range 113 dB

Maximum frequency resolution 8 Hz

Maximum scanning rate over 2,000 MHz/s

Power supplyMainsAutonomous

100-240V, 50Hz adapterBuilt-in battery operation time 1.5 hours

Main unit dimensions 500×350×120 mm

Main unit weight 5.8 kg

...continued

VoronOPTICAL CAMERAS DETECTOR

Main features:

• Technical solutions used in the VORON (roof

prism and translucent optics) allowed to

make its design exceptionally compact by

retaining excellent optical characteristics:

high magnification, wide field of view and

exceptional image quality.

• Efficient impulse source of power supply

ensures a long operation time from one AA-

type battery (1,5 V).

• VORON case is made of aluminum alloy; it

has a hand strap and soft rubber eyeshade.

• The device is easy-to-use and does not

require any special skills.

VORON is designed for a quick detection of

concealed micro video cameras, including those with

pinhole lenses.

The principle of detection is based on effect of light

reflection or “return flare”. Thus, when a concealed target

is detected, there is a bright red spot (reflection from a

video camera lens) in the VORON’s field of vision.

Detecting distance of concealed video cameras with

pinhole lenses (diameter of 1mm) can be from 1m to 20m

depending on operational conditions. VORON employs

LED illumination of targets what makes it a safe-to-use

device for operator (unlike laser illumination).

Operation on optical basis, but not radio frequency

range, allows this device to detect any optical device

regardless of its operating mode (on/off) and data

transmission type (radio or cable). Therefore, a radio

interference, electromagnetic shield, masking gauze or

lens hood does not reduce the likelihood of detection.

Delivery set:1. Voron device2. Clothing3. Hand strap4. Packing box


Magnification 5x

Angle of view, grad 12

Diopter correction range ± 4

Diameter of exit pupil, mm 4,5

Voltage 1.5 V

Running time on one battery 6 hours

Dimensions 50 x 68 x 140 mm

Weight 330 g

LadyaACOUSTIC NOISE GENERATOR FOR CELL PHONES

LADYA-D

LADYA-4

LADYA-10

Protection for 10 cell phones

Standarts detected GSM 900/1800/3 G / Wi - Fi / Bluetooth

Protection type acoustic noise

Power supply 220 V mains

Other features IR remote activation

Protection for 1 cell phone

Standarts detected GSM 900/1800/3 G /4 G / Sky link / Wi - Fi / BT


Power supply 220 V mains

Ladya - product series for acoustic protection of cell phones against unauthorised audio transmission.

Cell phone is placed into specially prepared enclosure. In case of remote activation of cell phone microphone

there is only one de-masking sign - change of electromagnetic field when cell phone tries to transmit audio

information. When unauthorised transmission is detected Ladya starts generating acoustic noise by means

of speaker inside its enclosure. Noise is passed directly to microphone of cell phone which is placed inside

Ladya and blocks all possible acoustic voice leak from surrounding environment.

Protection for 4 cell phones

Standarts detected GSM 900/1800/3 G / Wi - Fi / Bluetooth


Power supply 4 Ah Li-Ion battery


Quantity of channels 1

Number of transducers (max) 4

Transducer impedance 8 ±2 Ohm


Weight no more than 0,5 kg

LGS series (LGS-403) (page 1 of 2)

VIBROACOUSTIC PROTECTION

Vibroacoustic and acoustic noise interference protection

The vibroacoustic and acoustic interference system is designed to counteract special unauthorized data

retrieval devices that use the room’s walling as leak channels. Such devices include:

• electronic and acoustic stethoscopes that are used for tapping through ceilings, floors and walls;

• wired and wireless microphones mounted on the walling or water and heating pipes;

• laser and microwave data retrieval systems that operate through the window openings.

LGS products enables protection through generating broadband vibroacoustic noise interference on the

potentially hazardous room structures. Vibroacoustic noise interference is created by the generator and

transmitted to the structures through the vibration transducers. The Product also supports installation of an

acoustic radiator (loudspeaker) for protection of closed air spaces (air ducts, wells, etc.).

LGS-403 is a single-channel noise generator. The impedance of electromagnetic vibration transducers

constitutes 8 Ohm. The generator supports parallel or sequential connection of up to 4 electromagnetic

vibration transducers and of an acoustic radiator in such a way, that the overall load impedance would reach

8 ±2 Ohm. Up to 4 vibration transducers can be connected in total.

LGS-403 - 1 vibroacoustic channel - 4 transducers


Quantity of channels 2

Number of transducers (max) 32

Transducer impedance 8 ±2 Ohm

Working frequency band 9...11200 Hz

Distance Control By cable. Allows remote switch On/Off

Dimensions 115x145x40 mm

Power Supply 220 V, 50 Hz

LGS-404 (page 2 of 2)

VIBROACOUSTIC PROTECTION

Following transducers are available for LGS series of

vibroacoustic noise generators:

• LVP-2s vibration transducer is designed to generate

vibrations in various structural components (walls, ceilings,

floors) enclosing the allocated room;

• LVP-2t vibration transducer is designed to generate

vibrations in window’s glass and utilities (piping) that go

beyond the allocated room;

• LVP-2o is designed to generate vibrations in the glass of

the windows enclosing the allocated room.

• Acoustic noise - any 8 Ohm speaker could be used on

separate channel.

LGS-404 - 2 vibroacoustic channels - 32 transducers

Dimensions less than 40x25 mm

Weight less than 120 g

LGS-404 is a two-channel noise generator that supports connection of up to 16 transducers per channel. A

total of 32 transducers can be connected to the product. The product can also work with acoustic transducers

(dynamic radiators, acoustic systems, loudspeakers etc.). The terminals’ connection pattern depends on the

desired protection level and can be represented by the parallel, sequential or combined connection of the

required number of transducers.


Signal level at power cord plug in the frequency band of 10 - 150 kHz and receiver bandwidth of f=200 Hz at least 40 dBµV

Signal level at power cord plug in the frequency band of 0.15 - 30 MHz and receiver bandwidth of f=9 kHz at least 45 dBµV

Signal level at power cord plug in the frequency band of 30 - 300 MHz and receiver bandwidth of f=120 kHz at least 50 dBµV

Generator output signal level in the frequency band of 300 - 1800 MHz and receiver bandwidth of f=120 kHz at least 50 dBµV

Interspectrum correlations factor no more than 2

LGS-221220 V MAINS NOISE GENERATOR

220 V power grids Protection. AC circuits pose a double threat. First of all, acoustic data can be leaked

through the AC circuit (220 V). And secondly, there is a threat of information signals leak from office equipment.

There exist passive and active techniques for AC (220 V) protection against unauthorized data retrieval:

• Passive 220 V circuits protection implies using anti-interference line filters. Such filters weaken any

signals in the frequency band of 0.01-1,000 MHz with the efficiency of at least 60 dB and, thus, do not

let the information signals generated in office equipment get through. Besides, a correctly installed filter

also protects office equipment from the harmful effect of external interference. It’s worth mentioning

that efficient operation of anti-interference filters requires high-quality grounding.

• Active AC circuits (220 V) protection techniques imply generation of a noise signal exceeding the

information signals and signals of information retrieval devices in level by special generators. Such noise

signals are supplied to the 220 V circuit and to the ground circuit. These generators produce noise for 220

V circuits and ground circuits.

LGS-221 is an information security device that is designed to actively protect informatization equipment

against information leaks through the power grid and ground system. The Product provides protection

against data leaks through the 220 V single-phase three-wire power grid with the frequency of 50 Hz by

generating broadband noise interference in all the masking interference conductors in power supply and

ground circuits in the frequency band of 0.01 – 1,800 MHz.

Power consumption no more than 40 W

Power voltage ~ 220 V / 50 Hz


Weight no more than 0,5 kg

Pilot-MEXPLOSIVE DETECTOR

Pilot-M has unique technical specifications and can

detect both vapors and determine a quantity of explosives

indoors or at any means of transport (cars, planes, trains,

ships and other). Detection is conducted by taking air

samples from inner space of inspected objects and their

subsequent analysis.

Remote tier with a grid thickener (part of delivery set) allows

to take samples in dusty and smoky areas. Furthermore,

there is a method of taking samples by special napkins,

that are later warmed up in a sample heater, which is also

added to a delivery set.

Pilot-M allows detecting track quantities of explosive based upon TNT, NG, EGDN, PENT (PETN), RDX, HMX,

Tetril, cellulose nitro compound gunpowder, including the ones on their base:

• Nitroglycerine (NG), EGDN, trinitrotoluene (tol, trotyl, TNT), PENT (tetranitrapentaerythrit,

pentaerythrittetranitrate, Pentrit, PETN), hexogen (RDX), oktogen (HMX), tetryl (Tetril),

threeacetonethreeperoxide (Cyclethreeacetonethreeperoxide, TATP) and nitrocellulose powders,

including explosive mixes: Semtex and other plastic and elastic explosives on the basis of RDX, PENT or

their mixture

• B-type compositions (ТГ-20, ТГ-40, ТГ-60, МС, ТГАФ)*,

• C-type mix (С1, С2, С3, С4, ПВВ-4, ПВВ-5А, ПВВ-7, ПВВ-12М, ЭВВ-11, ЭВВ-32 and etc.)*,

• Н-6, HBX, Minol-2, Amatol, Primacord, Primasheet, Tetritol, Tritonal, Cordit N, А-IX-1, А-IX-2, А-IX-20,

• explosives of Octols & Ocfols families and some other substances.

*- explosive of Russian origin


Sensitivity threshold (TNT sample) at 20 ± 2 °С, non less than, g/cm3 10-13

Response time, sec 1

Maximum distance between VD nozzle and examined object, mm 30

Alarm indication Visual and audible

Dimensions, mm 300 х 180 х 90

VD mass (incl. battery), kg 2

Power source DC 6V rechargea-ble battery

The device construction and unique analysis of algo-rithms provide with high precision and noise reduction.

In contrast to analogue equipment Pilot-M doesn't con-tain radioactive source and is absolutely safe for opera-tor and environment. Therefore, there are no limitations for purchasing, keeping, transporting, and utilization of the device.

Pilot-M1 uses special software allows comparing reg-istered spectrum to typical spectrum of pure and mixed explosives and sending it to a remote PC.

Anker-4EEXPLOSIVE TIMING DEVICES DETECTOR

Anker-4E detects various timing devices:

mechanical, electromechanical, electronic, as well as

other electronic devices and gears by their electric,

magnetic, acoustic and vibrating emissions.

Detects:• Electromechanical timing devices at an up to

40 cm range.

• Electronic timing devices at an up to 10 cm

range.

• Radio signal receivers at an up to 15 cm range.

Application:• Suspicious items inspection – RC IED or

explosive devices with clock retarders.

• Searching for persons hidden in shelters.

• Aircraft inspection.

Main features• Detection of periodic rhythms of mechanical

and electronic timers in improvised explosive

devices (I.E.D.).

• Detection of electronic timers, including

electronic wrist-watch based.

• The device is simple in use, lightweight and

compact.

• The device also has the capability to inspect

closed packages and handbags with the help

of a needle-shaped acoustic microphone.

• Test targets (mechanical, electromechanical

and electronic) are available.

• Can be used in places where active radio-

electronic equipment is not permitted


Indication headphones

Power supply 4 x AA cell

Continuous operation time not less than 30h

Dimensions (length/diameter) 510mm / 34mm

Operational temperature range +5º C…+40º C

Weight (ready for operational / in standard packing) 0.65kg / 2.4kg

Norka X-Ray (page 1 of 2)

X-RAY INSPECTION SYSTEMS

NORKA has a wide range of applications: customs,

law enforcement, airport security and other areas.

It is used for:

• Inspection of mail, parcels and small articles

• Detection of weapons, bombs, wires and

explosive devices in various packaging

• Detection of concealed eavesdropping devices

in furniture, office equipment, etc.

• Non-destructive testing and evaluation

The NORKA X-ray system is easy to use, reliable and

completely safe in operation. It provides excellent

detecting capability with no harmful effects to its

users or servicepersonnel.

NORKA is a unique portable X-ray inspection

system with a minifocus and microfocus constant

potential X-ray source. The voltage can be adjusted

from 20 to 160kV. This allows inspecting objects

made from different materials with various density

and thickness (20-70kV is the optimal voltage for

checking mail and thin objects, while 100-160kV

works best for baggage and thick objects). One

of NORKA’s advantages is its ability to inspect

areas of an object in fine details using geometric

magnification (up to 40 times).

Dual energy option allows recognizing organic and inorganic objects.

Norka X-Ray (page 2 of 2)

X-RAY INSPECTION SYSTEMS

The microfocus X-ray unit has a 30-micron focal spot rather than a 1 mm spot used in conventional X-ray

systems. In this case resolution attains an unprecedented 25 micron of a copper wire equivalent. Moreover,

the distance between an object and the X-ray source can be minimal, down to a few centimeters or even a few

millimeters when using geometric magnification.

The images are reproduced on a display screen of the control unit in a positive/ negative form, pseudo colours,

with enhanced contrast or in dual energy mode. Zooming in on any of the nine areas of the screen allows

better identification. Obtained images can be stored in the control unit memory for further investigation or

reference (up to 30,000 images). Stored images can also be edited and provided with additional text, graphics

and voice information.

If necessary, these images can be rewritten from the D:\images directory of a “BU-4” control unit to a USB flash

drive. Universal power supply (85 - 240 VAC 50/60Hz) allows easy operation anywhere in the world. This is the

only system on the market that works from -20°С to +50°С with humidity up to 90%.

The NORKA X-ray system is delivered in two handy carrying bags or in one case.


X-RAY UNIT RE-160 RE-120 RE-150MN RAP 220-5

Operation mode 5-25 second exposures in single energy mode

Max. X-ray tube voltage, kV 160 120 150 220

Focal spot size, μm 800 600 80 2000

Resolution (copper wire), μm 80 60 40 80

Total penetration (Al equivalent), mm 120 65 80 200

Total penetration (Fe equivalent), mm 40 24 20 60

X-RAY IMAGE CONVERTER

Сamera unit Digital - SKB-3D 1280х1024, 14 bit

Interchangeable converter - screeningarea, mm

“PR-4” - 190х250

“PR-5” - 300х400 (standard)

PR-6” - 410х550

CONTROL UNIT “BU-4”

Display 12” colour TFT touch screen display

Memory size (image number ) 30 000

Battery life 2 hours, or 60 X-ray image acquisitions

Operating temperature - 20о С to +50о С (-4о F to +122о F)

Relative humidity 90 % (35о С / 95о F)

Weight, kg less than 29 (Standard system configuration (NORKA with RE-150MN)

Inspection Mirrors Overview INSPECTION MIRRORS

We are glad to announce that SEKOTECH LTD expanded its product range and is now ready to offer high

quality inspection mirrors commonly used by safety and security authorities like police, border control &

guard agencies, anti-terrorism, rescue, other private security agencies and etc.

Because of high quality materials and firm construction the inspection mirrors can be used under any weather

and light conditions. Therefore, depending on customer’s needs and purpose we can offer a wide array of

modifications and packages available:

• Compact, pocket mirrors that can be easily & quickly assembled and used for object inspection.

• Inspection mirrors with telescopic bar (adjustable handle): from 60 cm and up to 300 cm length, modifiable

according to customer needs.

• A regular or LED flashlight can be mounted to the inspection mirror’s handle or inside of it.

• Reflectors can be replaced with various sizes and shapes (circle, square).

• We can also offer a large convex wide-angle mirrors on wheels dedicated for vehicle bottom inspection.

Moreover, these inspection mirrors can be produced according to client needs and of various size, shape and modification.

Please find several examples below. Since we are able to offer even more types than presented here we

encourage you to get in touch with us.

IMFL-1510 VUIM-LED-60IMLED-1500

IMFL-1510 With Telescopic Bar

INSPECTION MIRRORS

Inspection kit consists of four section ergonomically designed robust telescopic bar with mounted flashlight

bracket. Handle is covered with the insulating material. Kit includes three glass mirrors.

IMFL-1510 inspection mirror kit is

used for visual inspection of hard

to reach places, in various lighting

conditions.

Designed for: • Security services• Customs• Police• Rescue services• TSCM teams


The length of the telescopic arm (extended) 1510 mm

The length of the telescopic arm (folded) 525 mm

Mirror tilt 0 ... 1150

Mirror size (mirror 1) Ø 142 mm


Mirror size (mirror 3) 68 x 126 mm

Power source 2 x D type batteries

Light source Krypton bulb

Weight 690 g

Delivery set:1. Telescopic arm with hand strap2. Mirror - 142 mm diameter3. Mirror - 70 mm diameter4. Mirror - 68 x 126 rectangle5. Flashlight6. Packing bag

IMLED-1500 Telescopic Bar + LED Light

INSPECTION MIRRORS


The length of the telescopic arm (extended) 1500 mm

The length of the telescopic arm (folded) 505 mm

Mirror tilt 0 ... 1150


Mirror size (mirror 2) 68 x 126 mm

Power source 3 x AA type batteries

LED illuminator 6 LEDs

Weight 750 g

Delivery set:1. Telescopic arm with embedded

LED illuminator and hand strap2. Mirror - 142 mm diameter3. Mirror - 68 x 126 rectangle4. Packing bag

D-LED-1500 inspection mirror kit is used for visual inspection of hard

to reach places, in various lighting

conditions.

Designed for: • Security services• Customs• Police• Rescue services• TSCM teams

Inspection kit consists of four section ergonomically designed robust telescopic bar with embedded LED

illuminator. Handle is covered with the insulating material. Kit includes two glass mirrors. Embedded

illuminator is fitted with 6 high luminosity LEDs and has two power modes.

VUIM-LED-60 Vehicle Inspection

INSPECTION MIRRORS


Carriage dimensions 344 x 374 mm

Mirror dimensions 290 x 320mm

Handle length 1200 mm

Power source 6 AAA type batteries

LED panel 60 LEDs

Weight 4 kg

Delivery set:1. Mirror carriage2. Light source with 60 LEDs3. Handle with hand strap4. Packing bag

A robust under vehicle search mirror, designed for detailed searching of the

underside of vehicles in conditions of insufficient illumination.

The search mirror has a large convex wide-angle mirror for maximum

observation, which is mounted on a tough wheeled base, and a detachable

LED lighting panel with variable illumination brightness. The LED panel is

mounted on a carriage by magnetic holders. If necessary, the LED panel can

be detached and used as a lantern.

The carriage is moving on 4 small dimension rotary wheels, which makes it

possible to roll the carriage under vehicles of low clearance. Each wheel rotary

unit is equipped with 2 bearings, which allows to turn the carriage without

jerking.

ZD seriesINSPECTION MIRRORS

Their ability to facilitate visual inspection of hard-to-

reach places including the dark ones can be used:

• by technical structures for examination of a state of

various objects;

• by customs services for inspection and supervision

of passenger traffic and freight transport;

• by rescue services when eliminating the effects of

emergency situations (inspection of blockages and

hard-to-reach places);

• for inspection of municipal engineering objects

(wells, elevator equipment, collecting channels, etc.);

• when performing examination and maintenance

works in transportation facilities;

• by rescue and security services for performing

special operations.

Main features:• Low-weight LED illuminating lamp supplied by

three rechargeable batteries (AAA type). The

lamp can be readily extracted from a holder and

used independently;

• Set of mirrors of various sizes and shapes (at the

customer’s option);

• Two types of used optical materials: glass and

reflecting plastic;

• Simple and reliable mirror holding/inclination

assembly;

• Working length is up to 2.5 m;

• Monocular for detailed examination of distant

objects with an 8X magnification;

Delivery set:1. Telescopic arm;2. Mirrors: rectangular mirror and two round ones;3. Illuminating lamp;4. 8X monocular;5. Two sets of rechargeable batteries;6. Charger;7. Packing bag.

JSC SekotechAvizu str. 2-1408435 VilniusLithuania

VAT No. LT100007374115

Phone +47 967 44174E-Mail [email protected] www.sekotech.comSkype sekotech

AM FM PSK FSK ...WiFi

2.4 GHz

4G

Bluetooth

GSM

UMTS CDMA DECT

detection analysis location - sekotechsekotech.com/files/sekotech-2014-04-tscm-catalog.pdf ·...

Documents