direct replacement for sidel model universal...
TRANSCRIPT
Direct Replacementfor Sidel ® Model
Universal Machines
for the Plastic Bottle Blowing Industry
STRETCH ROD CYLINDERS FOR SIDEL® UNIVERSAL MACHINES
UNIVERSAL02
• Longer Life
• Reduces Maintenance and Downtime
• Direct Replacement
PLA
STIC
PA
CKA
GING COMPONEN
TS
GR
OUP
SOLUTIONS
Quality
Delivery
Support
A divisionof PHDPLA
STIC
PA
CKA
GING COMPONEN
TS
GR
OUP
SOLUTIONS
Quality
Delivery
Support
A divisionof PHD
HEAT SET WITHOUT BALAYAGE
ML# 309397 HEAT SET ML# 309326
CSDML# 308217
SB034 ML# 309360
�SOLUTIONS FORINDUSTRIAL AUTOMATION
(800) 624-8511www.phdinc.com UNIVERSAL0�
© Copyright �009, by PHD, Inc. All Rights Reserved. Printed in the U.S.A.
How is the machine being run?
CSD - If yes, order ML306987 (unit without valve)(1)or ML308217 (unit with valve)
Heat Set - Is Balayage only being used? If YES, ML307364 (without valve)(2)or ML309326 (with valve)
Heat Set - Instead of Balayage, is there back pressure (full blow) on stretch rod during retract?If YES, then ML307592 (without valve) (3)or ML309397 (with valve)
(This is the case often when machine is heat set, but running CSD bottles)
Shock Absorber used on stretch rod cylinder retract?If NO, contact PHD before ordering.
Cold Set on an SB034? Standard cylinders issued on this machine are only 290mm in stroke, as opposed to 400mm.This cylinder has a different stroke, a different flange and the alignment of the flange/check valve is different than the othercylinders for the Universal. If YES, order ML309360 (4) for unit with valve, ML309361 for a unit without valve, or ML309734for a unit with a valve and heat set style mufflers.
Recommended Set Up Instructions –Start with cushion needle in fully closed position
(1) IF NO BACK PRESSURE, adjust cushion needle 1/2 to 1 full turn from fully closed position. IF BACK PRESSURE, adjust cushion needle 1-1/2 to 2 full turns from fully closed position.
(2) Adjust cushion needle 4 full turns from fully closed position. If used in conjunction with shock absorber on retract, then open counterclockwise until fully open.
(3) Adjust cushion needle 1-1/4 turns from fully closed position.
Factory recommended guidelines only - customer will need to adjust accordingly tohis specific loads and speed.
ORDERING GUIDE: UNIVERSAL CYLINDER
CSDML# 308217
Heat SetML# 309326
SB034ML# 309360
Heat Set without BalayageML# 309397
Recommended Set Up Instructions
(800) 624-8511www.phdinc.com
�SOLUTIONS FORINDUSTRIAL AUTOMATION UNIVERSAL0�
SPECIFICATIONS IMPERIAL METRICTYPE Pneumatic CylinderSERIES Universal Machines Stretch Rod CylinderBORE SIZE 1.969 in 50 mmBORE AREA - EXTEND 3.04 in2 1963 mm2
BORE AREA - RETRACT 2.56 in2 1649 mm2
THEORETICAL OUTPUT 264.5 lb @ 87 psi 1176.6 N @ 6 barOPERATION Double ActingOPERATING PRESSURE RANGE 7.5 - 150 psi 0.5 - 10 barAMBIENT TEMPERATURE �20� to 180� F �29� to 82� CADJUSTABLE CUSHION - RETRACT StandardLUBRICATION; FOOD GRADE FDA Regulation 21 CFR 178.3570STROKE 15.692 in 400 mm (SB034) 11.417 in 290 mmSTROKE TOLERANCE �.079/-.000 in �2.0/-0.0 mmSHOCK PAD Thermoplastic Polyester Elastomer (TPE)HEADS & CAPS Anodized AluminumCYLINDER TUBE Anodized AluminumPISTON ROD Hard Chrome Plated SteelROD BEARING Internally Lubricated PolymerPISTON & ROD SEALS Urethane
VALVE SPECIFICATIONSSERIES ISO 2 (ISO 5599/1)FUNCTION 5/2OPERATOR SinglePILOT InternalSPOOL RETURN SpringSOLENOID 24 VDC (5.4 W)VOLTAGE RANGE �15� to �10� from NominalELECTRICAL CONNECTOR DIN 43650, Form AMANUAL OPERATOR Non-locking RecessedPILOT EXHAUST MuffledFLOW 3.0 CvLUBRICATION FDA Regulation 21 CFR 1789.3570FILTRATION 40 MicronOPERATING PRESSURE RANGE 20 to 150 psi [1.37 to 10 bar]AMBIENT FLUID TEMPERATURE 0� to 120� F [�18� to 50� C]
now retained for extreme applicationsinternally lubricated engineered
polymer bearing for long service life
standard alloy steelpiston rods are hard chromeplated for maximum life and
durability
built-in shock pads are standard,absorbing impact energy and eliminatingmetal to metal contact
PTFE wear ring providespiston support andenhances durability
cylinder features urethanepiston and rod seals forlong life
rugged andlightweight
aluminum alloyhead, cap,
and tube
increased capacity cushioncontrols are easily adjusted
and are field repairable,maximizing your investment
rod sealretention ringfor extremeapplications
Common Benefits
• PHD Cylinder mounts into the same space and bolt patterns. • Provides significantly longer life and reduces maintenance and downtime. • Mounting options provide ease of design into application.• Internal shock pads are standard, eliminating metal to metal contact. • Cushion controls are standard for end of stroke deceleration.• Cylinders are easily field repairable, maximizing your investment.
Industry Uses
• Plastic Packaging - Stretch Blow Molding
Any marks or names referenced herein are either registered trademarks or trademarks of their respective owners. No association with or endorsement of any company, organization, or product is intended or should be inferred.
UNIVERSAL MACHINES STRETCH ROD CYLINDER■ Direct replacement for Sidel® Model
Universal Machines
• Provides Significantly Longer Life • Direct Replacement • Reduces Maintenance and Downtime
enhanced
enhanced
enhanced
STRETCH ROD CYLINDERS FOR SIDEL® UNIVERSAL MACHINES
�SOLUTIONS FORINDUSTRIAL AUTOMATION
(800) 624-8511www.phdinc.com UNIVERSAL0�
ML#309360 for SB034, 290 mm stroke cylinder
ML#309734 for SB034, 290 mm stroke cylinder with heat set mufflers
2.439[62]1.653
[42]
1.063 [27]1.847[47]
3.150[80]
.984[25]
.886[22.5]
1.673 [42.5]
4X � .394[10] THRU 45�
Z
Z
SECTION Z-Z1:1
2.486[63.1]
� .236 [6]� .551 [14]
� .315 [8]
16.539[420.1]
3X .625[15.9]
1.102 [28]
5.512 [140]
� .630 [16]
8.464[215]
5.550[141]
3.425[87]
.551 [14]
.203 [5.2]
2.598[66]2.165
[55]
M10 x 1.5-6H THREADx DEPTH .709 [18] MIN
.354[9]
6.086[154.6] 4.409 [112]
4.143 [105.2]1.146 [29.1]
BLEED OFF VALVEDIN 43650 FORM ‘A’
CONNECTOR ON VALVE
8.578[217.9]
.886[22.5]
1.673 [42.5]
3.402[86.4]
6.543 [166.2]
ML309734WITH HEAT SET
MUFFLERS ONLY
Heat SetStyle MufflersML# �09��6ML# �09�97ML# �097��
DIMENSIONS: STRETCH ROD CYLINDERS
All dimensions are reference only unless specifically toleranced.
PHD, Inc.9009 Clubridge Drive
P.O. Box 9070, Fort Wayne, Indiana 46899 U.S.A.Phone (260) 747-6151 • Fax (260) 747-6754
www.phdinc.com • [email protected]
PHDinEurope GmbHArnold-Sommerfeld-Ring 252499 Baesweiler, Germany
Tel. +49 (0)2401 805 230 • Fax +49 (0)2401 805 232www.phdinc.com • [email protected]
�M �/09 779�
3X
Z
Z
SECTION Z-Z
SECTION K-K
MECHANICAL INDICATORFOR PNEUMATIC PRESSURE
(RED IN COLOR -EXTENDS .2 [3mm])
20.870 [530.1].394 [10]
2.486[63.1]
M10 x 1.5-6H THREADx DEPTH .787 [20] MIN
.039 [1]
� .551[14]
� .315[8]
2.378[60.4]
8.11[206.1]
� 5.551 [141]
2X�� .236 [6]ML#309397 & ML#309326
2X�� .315 [8] ML#3082171.850 [47]
DIN 43650 FORM “A”CONNECTOR ON VALVE
BLEED OFF VALVE
2.165 [.787]5.514 [140]
±.205 [5.2]� .630 [16]
1.812[46]
1.756 [44.6]4.752
[120.7]1.102 [28]
.197 [5]
1.240[31.5]
2.480[63]
4X � .702[17.8]
4X � .482[12.2]
1.373[34.9]
NOTES:1) BORE � = 50 mm (1.969 in)2) STROKE = 400 mm (15.748 in)
.625[15.9]
2X 3.278 [83.3]ML#307592 & ML#309326
��1.142 [29]
K
K��.394[10]
2X���.875 [22.2]
3.455[87.8]
1.378 [35]
1.378[35]
1.673 [42.5]
2.165 [55]
.984 [25] x 45
7.677 [195]
1.673 [42.5]
2.165 [55]1.673 [42.5]
2X .197 [5] x 45
.886 [22.5].886 [22.5]
2X .916 [23.5]
ML#309397, ML#308217, ML#309326
CSD Style MufflersML# �09�60