directed passive keyless entry (pke) model 2102t

This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical

system and components.

© 2012 Directed, Vista, CA N2102T 2012-07

Directed Passive Keyless Entry (PKE)Model 2102T

Installation Guide

ContentsAntenna Mounting and Installation Points ��5

Vehicle Category Installation Specification ��5Installation Type Selection ��6Installation diagram ��7Wiring connections ��19

D2D port (H2), 4-pin black connector ��19Feature Programming ��20

Entering feature programming routine ��20Changing feature options ��20Accessing another feature ��20Exiting feature programming ��20Features and Options List ��21

SmartLock feature ��22Remote pairing ��23

Pairing the FOB to the PKE module: ��23Pairing the PKE system to the remote starter module: ��23

Factory reset ��23Diagnostics ��23

4 © 2012 Directed� All rights reserved�

Warning! safety first

The following safety warnings must be observed at all times:Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer.When properly installed, this system can lock and unlock your doors and also arm and disarm your Directed security system when the key fob is in and out of range.

The following precautions are the sole responsibility of the user; however, authorized Directed dealers should:Never use a test light or logic probe when installing this unit. Always use a multimeter.

5© 2012 Directed� All rights reserved�

Antenna Mounting and Installation Points

In order to maximize range, the following antenna mounting options should be discussed with the customer to better suit their needs.

Warning• Do not directly mount the antenna on any metallic surface, this may significally decrease the range. • To insure consistent operation, secure the antenna and make sure they will not move or dangle.• Antennas are fragile, they can break easily. Make sure they are mounted on a solid (non flexible) part.

Recommended Antenna Mounting Locations

The recommended antenna mounting locations are for reference only. It is still required that you perform the actual range test when installing the antenna to ensure that the range is satisfactory. You may require to relocate the antennas to different areas around the recommended locations until maximum range is achieved.

Option 1 Option 2 Option 3Antennas

Since this is a directional antenna, range will be a�ected by antenna placement/mounting

Horizontal rangeVertical range

Option 4

Note: An optionnal 12-foot antenna (part# SANT-PKE12) can be installed to increase the active zone coverage. When a third antenna is installed, feature 4, option 2 must be enable through the "Features and Options List" section on page 21.

Vehicle Category Installation Specification

Sub Compact, Compact & Sedan:For optimal performance, install the 18-foot antenna in the headliner or below the rear deck. Note: Installation in the trunk will greatly affect and reduce range and overall system performance.

Minivan & SUV: To maximize range in the rear of the vehicle, install the 18-foot antenna in the headliner.

Pickup (with cab) & Cargo:To maximize range in the rear of the vehicle, install the 18-foot antenna in the bumper, behind the license plate.

Pickup (without cab):Suggested Installation: Option 3. Antennas should be mounted on the driver and passenger side since the tailgate does not require to be controlled.

Convertible:Install 8-foot antenna in windshield pillar on driver side and the 18-feet antenna behind the rear seats.

Note: On vehicle with fiberglass bodies or convertibles, the range will be significantly increased.


Installation Type Selection

Choosing the right installation type according to the device you install.

Corresponding installation type according to what device you are installing Page

Type 1 - PKE Standalone page 7

Type 2a - PKE + Xpresskit Bypass + AutoStart or AstroStart or Viper/Python/Clifford Directed Remote Starter (with 4-pin antenna connector)

page 8

Type 2b - PKE + Xpresskit Bypass + Viper/Python/Clifford Directed Remote Starter (with 6-pin antenna connector)

page 9

Type 3a - PKE + Xpresskit Bypass + DIRECTED SmartStart + Autostart or Astrostart Directed Remote Starter (with 4-pin antenna connector)

page 10

Type 3b - PKE + Xpresskit Bypass + DIRECTED SmartStart + Viper/Python/Clifford Directed Remote Starter (with 6-pin antenna connector)

page 11

Type 3c - PKE + Xpresskit Bypass + DIRECTED SmartStart + Viper/Python/Clifford Directed Remote Starter (with 4-pin antenna connector)

page 12

Type 4 - PKE + 4x10/5x10 page 13

Type 5 - PKE + Xpresskit Bypass page 14

Type 6 - PKE + DIRECTED SmartStart + 4x10/5x10 page 15

Type 7 - PKE + Xpresskit Bypass - Remote Start Ready (RSR) + DIRECTED SmartStart page 16

Type 8 - PKE + Xpresskit Bypass - Range Extender (RXT) + XL202 page 17

Type 9 - PKE + AutoStart or AstroStart or Viper/Python/Clifford Directed Remote Starter (with 4pin antenna connector)

page 18


Installation diagram

Type 1 - PKE Standalone

6 Green

6 Black

4 Red

2 Black

2 Black

2 Red

10 Black

LED

PK

E

Prog. Button

(-) Unlock Output: Blue: 2(-) Lock Output: Green: 1

(+) Door Sense Input: White/Purple: 4**

(-) Starter Kill Output: White/Black: 6(-) Parking Light Output: White/Pink: 7(-) Door Sense Input: Blue/White: 10**

(-) Unlock(-) Lock

(+) Brake(+) Starter

(+) Ignition(-) Parking Light

(-) Door Sense**

Antenna (8 feet)

Antenna (18 feet)

86 853087a

87

(+) Brake Input: Purple/Black: 5

(+) Door Sense**

Starter Disable:This connection isoptional and ad-ditional parts aresold separately.

Refer to the Antenna Locationand Installation Pointssection on page 5 formore information.

(-) Horn Output: Red/White: 3

(-) Horn

This toggle switch willbypass the starter disable.

(-) Ground: Black: 2RX: Blue: 1

(+) 12v: Red: 4

D2D Y CABLE

Cut the 4-wire red connector of D2D Y-cable and connect 12v and Ground wires to the corresponding wires of the DIRECTED SmartStartTM cable.

Not Used

Ground: Black(+)12v: Red

Ground: Black

(+)12v: Red

*Sold separately.**Door sense: The polarity of the door sense in the vehicle will determine which wire to connectfrom the PKE to the DIRECTED Remote Starter.

2 Wh

ite

OptionalAntenna (12 feet)*(Part# SANT-PKE12)


Type 2a - PKE + Xpresskit Bypass + AutoStart or AstroStart or Viper/Python/Clifford Directed Remote Starter (with 4-pin antenna connector)Note: 8210 Antenna Universal Adapter is required and sold separately.

These wires are not required in D2D mode.

4 Red

(-) Door Status Output

(+) Brake Output


(-) Starter Kill: White/Black: 6(-) Door Sense Input: Blue/White: 10***

(+) Brake Input(-) Door Sense Input***

Rem

ote

Sta

rter*

8210 Main UniversalAdaptor*: Refer to the8210 guide.

Regular Remote Start Connections

To The Vehicle

4 Wh

ite

(+) 12v: Red: 4

(-) Ground: Black: 2RX: Green: 3

TX: Blue: 1

RX: Blue: 1

TX: Green: 3(-) Ground: Black: 2

(+) 12v: Red: 4


(+) 12v: Red: 4

Xp

ressk

itIn

terfa

ce M

od

ule

*

D2D Y CABLE

6 Green

6 Black

4 Red

2 Black

2 Red

10 Black

LED

PK

E

Prog. Button

Antenna** 8210*Antenna Harness**

8210*

*Sold separately.**Antenna & Antenna harness are sold with your Remote Starter kit.*** Door sense: The polarity of the door sense in the vehicle will determine which wire to connectfrom the PKE to the DIRECTED Remote Starter.

D2D

PortA

ntenna

D2D

Port


Antenna (8 feet)

Antenna (18 feet)Refer to the Antenna Locationand Installation Pointssection on page 5 formore information.

(+) Ignition Output

86 853087a

87

(+) Starter Wire

4 wires red connector

4 wires white connector

3 wires redconnector



(+) Door Sense Input: White/Purple: 4***

(+) Door Sense Input***

2 Wh

ite



Type 2b - PKE + Xpresskit Bypass + Viper/Python/Clifford Directed Remote Starter (with 6-pin antenna connector)


4 Red

(-) Door Status Output

(+) Brake Output


(-) Starter Kill: White/Black: 6(-) Door Sense Input: Blue/White: 10****

(+) Brake Input

(+) Ignition Output

(-) Door Sense Input****

Rem

ote

Sta

rter*

4 Wh

ite


(+) 12v: Red: 4

Xp

ressk

itIn

terfa

ce M

od

ule

*(+) Door Sense Input: White/Purple: 4****

(+) Door Sense Input****

D2D Y CABLE

6 Green

6 Black

4 Red

2 Black

2 Red

10 Black

LED

PK

E

Prog. Button

Antenna**

Antenna H

arness**

*Sold separately.**Antenna & Antenna harness are sold with your Remote Starter kit.***10-foot Antenna Cable is included in the PKE kit.**** Door sense: The polarity of the door sense in the vehicle will determine which wire to connectfrom the PKE to the DIRECTED Remote Starter.

D2D

PortA

ntenna

10-foot Antenna Cable***

D2D

Port

(+) 12v: Red: 4


TX: Blue: 1

RX: Blue: 1


(+) 12v: Red: 4

86 853087a

87

(+) Starter Wire

Antenna (8 feet)



To The Vehicle



4 wires white connector





2 Wh

ite


Type 3a - PKE + Xpresskit Bypass + DIRECTED SmartStart + Autostart or Astrostart Directed Remote Starter (with 4-pin antenna connector)Note: 8210 Antenna Universal Adapter is required and sold separately.


(-) Door Status Output(+) Brake Output


(-) Starter Kill: White/Black: 6(-) Door Sense Input: Blue/White: 10****

(+) Brake Input(-) Door Sense Input****


To The Vehicle

4 Wh

ite


(+) 12v: Red: 4

Xp

ressk

itIn

terfa

ce M

od

ule

*

(+) Door Sense Input: White/Purple: 4****


LED

CABLE***

6 Green

6 Black

4 Red

2 Black

2 Red

10 Black

LED

PK

E

Prog. Button

The connector dependsof the installed bypass.

Refer to the DIRECTED SmartStartinstall guide for proper connection.

4 Red

Au

tosta

rt RS*

Astro

start R

S*

The remote starter model willdetermine which connector to use.Refer to the DIRECTED SmartStart

install guide for proper connection.

DIRECTED SmartStartTM *

*Sold separately.**Antenna & Antenna harness are sold with your Remote Starter kit.***DIRECTED SmartStartTM cable is sold with your DIRECTED SmartStartTM system.**** Door sense: The polarity of the door sense in the vehicle will determine which wireto connect from the PKE to the DIRECTED Remote Starter.

D2D

PortA

ntenna

(+) 12v: Red: 4


TX: Blue: 1

RX: Blue: 1


(+) 12v: Red: 4


Antenna (8 feet)


D2D Y CABLE

Cut the 4-wire red connector of D2D Y-cable and connect RX (Blue),12v and Ground wires to the corresponding wires of the DIRECTED SmartStartTM cable.

Not Used

RX: BlueGround: Black

(+)12v: Red

(+) Ignition Output

86 853087a

87

(+) Starter Wire

Starter Disable:This connection isoptional and ad-ditional parts are sold separately.


8210 Main UniversalAdaptor*: Referto the 8210 guide.


8210*


2 Wh

ite



Type 3b - PKE + Xpresskit Bypass + DIRECTED SmartStart + Viper/Python/Clifford Directed Remote Starter (with 6-pin antenna connector)


(-) Starter Kill Output: White/Black: 6

(-) Door Sense Input: Blue/White: 10****


(+) Brake

(-) Door Sense****

(+) Door Sense****

AntennaRF Port

ESP RedConnector

ESP BlackConnector

6 Green

6 Black

4 Red

2 Black

2 Red

10 Black

LED

PK

E

Prog. Button

(-) Ground: Black: 2

(+) 12v: Red: 4

LED

(+)12vTX(-) GroundRX

D2D Y CABLE

Antenna**

Antenna H

arness**

10-foot Antenna Cable***

*Sold separately.**Antenna, Antenna harness & DIRECTED SmartStartTM cable are sold with your Remote Starter kit.***10-foot Antenna Cable is included in the PKE kit.**** Door sense: The polarity of the door sense in the vehicle will determine which wire to connect from the PKE to the DIRECTED Remote Starter.


Antenna (8 feet)


Connect these wiresto the vehicle.



(+) Ignition Output

86 853087a

87

(+) Starter Wire

Not Used




OR


D2D RedConnector

4 Wh

ite

Xp

ressk

itIn

terfa

ce M

od

ule

*

(+) 12v: Red: 4


TX: Blue: 1

2 Wh

ite



Type 3c - PKE + Xpresskit Bypass + DIRECTED SmartStart + Viper/Python/Clifford Directed Remote Starter (with 4-pin antenna connector)Note: 8210 Antenna Universal Adapter is required and sold separately.





(+) Brake

(-) Door Sense****

(+) Door Sense****

AntennaRF Port

ESP RedConnector

ESP BlackConnector

6 Green

6 Black

4 Red

2 Black

2 Red

10 Black

LED

PK

E

Prog. Button

(-) Ground: Black: 2

(+) 12v: Red: 4

LED


D2D Y CABLE

*Sold separately.**Antenna, Antenna harness & DIRECTED SmartStartTM cable are sold with your Remote Starter kit.***10-foot Antenna Cable is included in the PKE kit.**** Door sense: The polarity of the door sense in the vehicle will determine which wire to connect from the PKE to the DIRECTED Remote Starter.


Antenna (8 feet)




(+) Ignition Output

86 853087a

87

(+) Starter Wire

Not Used




OR


D2D RedConnector

4 Wh

ite

Xp

ressk

itIn

terfa

ce M

od

ule

*

(+) 12v: Red: 4


TX: Blue: 1


8210 Main UniversalAdaptor*: Referto the 8210 guide.


8210*

CABLE**

2 Wh

ite



Type 4 - PKE + 4x10/5x10

RX: Blue: 1(-) Ground: Black: 2

(+) 12v: Red: 4





(+) Brake Input

(-) Door Sense Input****



6 Green

6 Black

4 Red

2 Black

2 Red

10 Black

LED

PK

E

Prog. Button

Not Used

*

*Sold separately.**Antenna & Antenna harness are sold with your Remote Starter kit.***10-feet Antenna Cable is included in the PKE kit.****Door sense: The polarity of the door sense in the vehicle will determine which wire to connectfrom the PKE to the DIRECTED Remote Starter.

Antenna**

Antenna H

arness**

D2D

PortA

ntenna

10-feet Antenna Cable***

D2D Y CABLE


Antenna (8 feet)




(+) Ignition Output86 853087a

87

(+) Starter Wire




2 Wh

ite



Type 5 - PKE + Xpresskit Bypass

Not Used

(+) Door Sense Input: White/Purple: 4**


(-) Door Sense Input: Blue/White: 10**

(+) Brake Output(-) Door Sense Output**


(+) Door Sense Output**

4 Wh

ite

Xp

ressk

itIn

terfa

ce M

od

ule

*



RX: Blue: 1(-) Ground: Black: 2

TX: Green: 3(+) 12v: Red: 4

6 Green

6 Black

4 Red

2 Black

2 Red

10 Black

LED

PK

E

Prog. Button

RX: Blue: 1


(+) 12v: Red: 4

D2D Y CABLE

(-) Unlock Input(-) Lock Input

(-) Parking Light Output: Pink/White: 7

*Sold separately.**Door sense: The polarity of the door sense in the vehicle will determine which wire to connectfrom the PKE to the DIRECTED Remote Starter.

D2D

Port


Antenna (8 feet)




4 wires whiteconnector86 8530

87a

87

(+) Starter WireConnect these wires

to the vehicle.

(+) Ignition Output



2 Wh

ite



Type 6 - PKE + DIRECTED SmartStart + 4x10/5x10


6 Green

6 Black

4 Red

2 Black

2 Red

10 Black

LED

PK

E

Prog. Button

CABLE**

TX: Blue: 1

RX: Green: 3(-) Ground: Black: 2

(+) 12v: Red: 4

*Sold separately.**DIRECTED SmartStartTM cable is sold with your DIRECTED SmartStartTM.***Antenna & Antenna harness are sold with your Remote Starter kit.****10-feet Antenna Cable is included in the PKE kit.Note: Door sense: The polarity of the door sense in the vehicle will determine which wire to connect from the PKE to the DIRECTED Remote Starter.

*

(-) Ground: Black: 2(+) 12v: Red: 4

RX: Blue: 1

LED

D2D Y CABLE

Cut the unused connectors of D2D Y cable and connect RX (blue), 12v and Ground wires to the corresponding

wires of the D2D cable.

Not Used


(+)12v: Red

D2D

Port

An

tenn

a***A

ntenna Harness***

10-feet Antenna Cable****

Antenna (8 feet)




(+) Door Sense Input: White/Purple: 4(Door sense: See note)

(-) Starter Kill Output: White/Black: 6(-) Door Sense Input: Blue/White: 10

(Door sense: See note)

(+) Brake Input(-) Door Sense Input (See note)


(+) Door Sense Input (See note)


86 853087a

87

(+) Starter Wire


(+) Ignition Output



Not Used


2 Wh

ite



Type 7 - PKE + Xpresskit Bypass - Remote Start Ready (RSR) + DIRECTED SmartStart



(-) Door Sense Input: Blue/White: 10***



Rem

ote

Sta

rt read

yX

pre

sskit

Inte

rface

Mo

du

le*

RX: Blue: 1

(+) Starter

(+) Ignition

86 853087a

87

6 Green

6 Black

4 Red

2 Black

2 Red

10 Black

LED

PK

E

Prog. Button


LED

D2D Y CABLE

Cut the unused connectors of D2D Y cable and connect RX (blue), 12v and Ground wires to the corresponding

wires of the D2D cable.

Not Used

TX: Blue: 1

RX: Green: 3(-) Ground: Black: 2

(+) 12v: Red: 4



*Sold separately.**DIRECTED SmartStartTM cable is sold with your SmartStart system.***Door sense: The polarity of the door sense in the vehicle will determine which wire to connectfrom the PKE to the DIRECTED Remote Starter.

D2D

Port

Antenna (8 feet)




Starter Disable:This connection is optionaland additional parts are sold separately.



See Remote Start Ready (RSR)install guide according to your vehicle

for RSR connections details.


CABLE**


(+)12v: Red


Not Used

2 Wh

ite



Type 8 - PKE + Xpresskit Bypass - Range Extender (RXT) + XL202Note: 8210 Antenna Universal Adapter is required and sold separately.



(-) Door Sense Input: Blue/White: 10***



RX: Blue: 1

86 853087a

87

6 Green

6 Black

4 Red

2 Black

2 Red

10 Black

LED

PK

E

Prog. Button

D2D Y CABLE

Cut the unused connectors of D2D Ycable and connect 12v and Ground wires.

Not Used

Ground: Black(+)12v: Red


*Sold separately.**D2D XOVER Cable, Antenna and Antenna Harness are sold with your RF Kit.***Door sense: The polarity of the door sense in the vehicle will determine which wire to connectfrom the PKE to the DIRECTED Remote Starter.

XL202*

XL202: Range Extender

Ant

enna

D2D

Por

t

Ran

ge E

xte

nd

er (R

XT)

Xp

ressk

itIn

terfa

ce M

od

ule

*

D2D

Port

Antenna (8 feet)






8210*XOVER**


See Remote Start Ready (RSR)install guide according to your vehicle

for RSR connections details.

(+) Starter

(+) Ignition

Starter Disable:This connection is optionaland additional parts are sold separately.


2 Wh

ite



Type 9 - PKE + AutoStart or AstroStart or Viper/Python/Clifford Directed Remote Start-er (with 4pin antenna connector)Note: 8210 Antenna Universal Adapter is required and sold separately.

4 Red


(-) Starter Kill: White/Black: 6(-) Door Sense Input: Blue/White: 10***

(+) Brake Input(-) Door Sense Input***

Rem

ote

Sta

rter*



To The Vehicle6 G

reen6 B

lack

4 Red

2 Black

2 Red

10 Black

LED

PK

E

Prog. Button


8210*

*Sold separately.**Antenna & Antenna harness are sold with your Remote Starter kit.*** Door sense: The polarity of the door sense in the vehicle will determine which wire to connectfrom the PKE to the DIRECTED Remote Starter.

D2D

PortA

ntenna


Antenna (8 feet)


(+) Ignition Output

86 853087a

87

(+) Starter Wire




(+) Door Sense Input***

2 Wh

ite



Wiring connections

6 Green 6 Black

4 Red2 Black 2 Red10 Black

LED

PKE

Pro

g. B

utt

onAntenna Port Remote Start

Antenna Port

D2D

Por

t

Ant

enna

8-fo

ot

Ant

enna

18-

foot

Analog Port

2 White

Ant

enna

12-

foot

(Opt

iona

l)

Analog Port (H1), 10-pin white connector H1/1 GREEN (-) LOCK OUTPUT

H1/2 BLUE (-) UNLOCK OUTPUT

H1/3 RED/WHITE (-) HORN OUTPUT

H1/4 WHITE/PURPLE (+) DOOR SENSE INPUT*

H1/5 PURPLE/BLACK (+) BRAKE INPUT

H1/6 WHITE/BLACK (-) STARTER KILL OUTPUT

H1/7 PINK/WHITE (-) PARKING LIGHTS OUTPUT

H1/8 PURPLE No connection

H1/9 PINK No connection

H1/10 BLUE/WHITE (-) DOOR SENSE INPUT** Only one of the Door sense input is required for proper operation.

D2D port (H2), 4-pin black connector H2/1 BLUE RX

H2/2 BLACK (-) GROUND

H2/3 GREEN TX

H2/4 RED (+) 12V


Feature ProgrammingThe feature programming can be done by following the instructions below.

Entering feature programming routineTo select a Feature, press and release the programming button the corresponding number of times according to the table below, and then press and hold, the LED will flash to indicate the selected feature number.

To select this Fea-ture number...

Press the program-ming button...

And the LED will flashes...

Feature 1 Twice Once

Feature 2 3 times Twice

Feature 3 4 times 3 times




Changing feature optionsPress the programming button the corresponding number of times according to the selected option. The LED will flash the number of times according to the desired option. For example, if you select Option 3, you will press the programming button 3 times.

Accessing another featureTo change the option in another feature, wait 3 seconds after your last operation and the module will exit the menu program-ming. Repeat the steps in "Entering feature programming" and "Changing feature options" sections to select another feature and option.

Exiting feature programmingNo activity for 3 seconds.


Features and Options List

Features Options

1- RF Protocol Selection

1: Viper, Python, Clifford Supercode*Directed new generation receiver technology

2: Viper, Python, Clifford KeeloqDirected older generation receiver technology

3: AstroStart receiver technology

4: AS HDR - FMAutoStart HDR (new style FM based) receiver technology

5: AS HDR - AMAutoStart HDR (AM based) receiver technology

6: AS LDR - FMAutoStart LDR (older style) receiver technology

2- Door Unlock Timing

1: 0�8 sec*

2: 0�4 sec

3: 3�5 sec

4: Double pulse (0�25 sec)

3: Door Lock Timing

1: 0�8 sec*

2: 0�4 sec

3: 3�5 sec

4: Double pulse (0�25 sec)

4: Number of Antenna

1: 2 Antennas (8ft - 18ft)*

2: 3 Antennas (8ft - 12 ft - 18 ft)

3: 1 Antenna (8ft)

5: Smart Lock**

1: 3 minutes timer*

2: 0 minutes timer (No delay)

3: 1 minute timer

4: 5 minutes timer

6: Door Open Interlock

1: ON*The doors will lock as soon as the key fob leaves the zone even if a door is open�

2: OFFThe doors will not lock if the key fob leaves the zone while a door is open�

* Default option** See SmartLock feature section for more details.


SmartLock feature

The purpose of the SmartLock feature is to prevent the doors from unwanted unlocking/locking when entering/exiting the active zone multiple times for a pre-programmed delay (No delay*,1, 3 or 5 minutes). This is practical in situations such as loading/unloading packages.

*SmartLock feature is disabled when it is set to no delay, which is confi gurable.

Note: If the Door Open Interlock feature is enabled, the SmartLock feature will not be able to lock a door when it is left opened.For more information about using SmartLock feature, see owner's guide.

SmartLock feature diagram

1

2

3

FOB exits the zone: The doors lock, timer starts.

FOB re-enters the zone within the pre-programmed delay:Doors unlock, timer is reset and stays frozen.

FOB exits the zone: Doors stay unlocked, fresh timer re-starts.

4FOB re-enters the zone within the pre-programmed delay:Doors stay unlocked, timer is reset and stays frozen.

FOB exits the zone:Doors stay unlocked, fresh timer re-starts.

The doors will automatically lock once the valid key fob remainsout of the active zone longer than the pre-programmed delay. SmartLock feature CANCELLED.

SmartLock Feature ON

5

Step 3 & 4 will not cause the doors tolock/unlock aslong as the doorsare not opened/closed during the whole sequence.


Remote pairing

Important: The antennas must be connected to the PKE module before proceeding to pairing mode.RF Protocole Selection need to be done prior to pair the PKE to the remote starter. See "Feature Programming" section on page 20.

Pairing the FOB to the PKE module:1. Press and release, then press and hold the programming button on the PKE module. The LED will turn on solid indicating

that the PKE module is in pairing mode.2. Release the programming button.3. Quickly press and release then press and hold the remote

AUX

button.4. The fob LED will flash red followed by a green flash to confirm the pairing was successful. 5. If more than 1 red LED flash occurs during the programming process, verify antenna connections and repeat the pairing

procedure. Note: Press and release the programming button at any moment to exit remote pairing mode.

Pairing the PKE system to the remote starter module:This step is necessary when a remote starter is installed prior to having a PKE system. This allows the remote starter to recog-nize commands from the PKE system. It is important that the FOB be paired to the PKE module first before proceeding with this step. 1. Place the remote starter in remote pairing mode (see the remote starter instructions on remote pairing for more informa-

tion).2. Press and hold the programming button on the PKE. The LED will flash 3 times to confirm that data is being sent to the

remote starter.3. Release the programming button. The remote starter will confirm the remote learning operation. Refer to the remote starter

installation guide for more information on remote pairing.

Factory reset

To execute a factory reset:1. Disconnect the power supply from the PKE module.2. Press and hold the programming button.3. Reconnect the power supply to the module. The LED will flash 5 times quickly to confirm factory reset.

Diagnostics

LED Parking Lights Flashing rate Event

Flashes x1 Flashes x 1 Slow Lock

Flashes x 2 Flashes x 2 Slow Unlock

Flashes x 3 Flashes x 3 Fast Enabling PKE through FOB (Standalone installation only)

Flashes x 3 Flashes x 3 Slow Remote ID being sent to remote starter

Flashes x 4 Flashes x 4 Slow PKE learned

Flashes x 5 Flashes x 5 Fast Disabling PKE through FOB (Standalone installation only)

Flashes x 5 Flashes x 5 Fast Factory reset

ON continuously N/A ON con-tinuously PKE disabled

N2102T 2012-07

Vista, CA 92081www.directed.com

© 2012 Directed—All rights reserved

The company behind this system is DirectedSince its inception, Directed has had one purpose, to provide consumers

with the finest vehicle security and car stereo products and accessories avail-able. The recipient of nearly 100 patents and Innovations Awards in the

field of advanced electronic technology.

Directed is ISO 9001 registered.

Quality Directed products are sold and serviced throughout North America and around the world.

Call (800) 274-0200 for more information about our products and services.

Designed and Engineered in the USA

directed passive keyless entry (pke) model 2102t

Documents