Download - 2006 Rsx Fog Lights
-
7/31/2019 2006 Rsx Fog Lights
1/15
2005 American Honda Motor Co., Inc - All Rights Reserved. AII 30236 (0507) 1 of 1
INSTALLATION
INSTRUCTIONS
Accessory Application Publications No.
Issue Date
JULY 2005
2006 RSXFOG LIGHTS
P/N 08V31-S6M-212
PARTS LIST
Right fog light
Left fog light trim
Right fog light trim
Left bracket
Right bracket
Switch harness
Fog light harness
Switch
4 Stepped screws
2 Washer-screws, 4 x 8 mm
2 Washer-bolts, 5 x 12 mm
8 Washer-screws, 5 x 16 mm
8 Spring nuts
Relay
Washer-bolt, 6 x 12 mm
2 Lock washers
24 Wire ties
Left fog light
08V31-S6M-2010-91
Left subbracket
Right subbracket
BII 30236
-
7/31/2019 2006 Rsx Fog Lights
2/15
2 of 15 AII 30236 (0507) 2005 American Honda Motor Co., Inc - All Rights Reserved.
Wire tie with clip
Fuse label
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
8 mm and10 mm Combination wrenches
Ratchet
10 mm Socket
Illustration of Fog Lights Installed on the Vehicle
INSTALLATION
Customer Information: The information in this
installation instruction is intended for use only byskilled technicians who have the proper tools,
equipment, and training to correctly and safely addequipment to your vehicle. These procedures
should not be attempted by do-it-yourselfers.
NOTE: If you're also installing a front under spoiler,install the fog lights first.
1. Make sure you have the anti-theft code for theradio, then write down the radio station presets.
2. Disconnect the negative cable from the battery.
4415060Y
FUSEBOX
SWITCH
RELAY
SWITCHHARNESS
RIGHTFOG LIGHT
LEFTFOGLIGHTFOG
LIGHTHARNESS
-
7/31/2019 2006 Rsx Fog Lights
3/15
2005 American Honda Motor Co., Inc - All Rights Reserved. AII 30236 (0507) 3 of 1
BOLTNUT
BATTERYHOLDER
CLIP
POSITIVECABLE BATTERY
CLIPSELF-TAPPINGSCREW
LEFTFRONTINNERFENDER
Routing the Fog Light Harness
3. Disconnect the positive (+) cable from the battery,and release the clip from the holder bolt.
6. Remove the two self-tapping screws and one clip,
then pull the left front inner fender out in thedirection shown. Repeat on the right front innerfender.
4. Remove the bolt and the nut that fasten the
battery holder, and remove the holder and thebattery.
5. Remove the left lid from the front bumper (two
retaining tabs and one hook). Repeat on the rightlid.
4213070Y
RETAININGTAB
LEFT LID HOOK
FRONTBUMPER
-
7/31/2019 2006 Rsx Fog Lights
4/15
4 of 15 AII 30236 (0507) 2005 American Honda Motor Co., Inc - All Rights Reserved.
RELAY BOX
HOLE
FOG LIGHTHARNESS 2-PINCONNECTOR(short end)
FOG LIGHTHARNESS
WINDSHIELDWASHERTANK FILLERNECK
FOG LIGHT HARNESS1-PIN CONNECTOR
VEHICLE HARNESS
1-PIN CONNECTOR
BLUETAPE
BULKHEADUPPER FRAME
FOG LIGHTHARNESS 2-PINCONNECTOR(long end)
RIGHTHEADLIGHT
HOLEPOWER STEERINGFLUID RESERVOIR
FOG LIGHTHARNESS
Route in front of thebulkhead center stay.
BRACKET
7. Remove the windshield washer tank filler neck clip
from its holder.
8. Locate the 1-pin connector blue-taped to thevehicle harness routed under the relay box, and
remove the blue tape to free the connector.
9. Connect the 1-pin connector of the fog lightharness to the 1-pin connector of the vehicleharness you just freed.
10. Route the fog light harness 2-pin connector
(short end) down into the front bumper through thesame hole as the windshield washer tank filler
neck.
11. Route the fog light harness 2-pin connector (long
end) along the vehicle harness behind the leftheadlight and inside of the bulkhead upper frametoward the right (passengers) side of the vehicle.
Make sure the 2-pin connector is in front of thebulkhead center stay.
12. Remove the power steering fluid reservoir.Continue routing the fog light harness 2-pin
connector behind the right headlight along the
vehicle harness, then hang it down into the frontbumper through the hole at the rear of the rightheadlight.
-
7/31/2019 2006 Rsx Fog Lights
5/15
2005 American Honda Motor Co., Inc - All Rights Reserved. AII 30236 (0507) 5 of 1
WIRE TIE
FOG LIGHT HARNESS1-PIN CONNECTOR
FOG LIGHTHARNESS
WIRE TIEBRACKET
FOG LIGHTHARNESS
WIRETIE
FOG LIGHTHARNESS
BULKHEADUPPER FRAME
WIRE
TIES
WIRE TIEWITH CLIP
13. Secure the fog light harness 1-pin connector
connected behind the left headlight to the vehicleharness with one wire tie.
14. Secure the fog light harness to the vehicle
harness and the bracket on the left (drivers) sideof the vehicle using three wire ties in the areas
shown.
15. Secure the fog light harness to the hole in the
bulkhead upper frame with the wire tie with clip.
16. Secure the fog light harness to the vehicleharness along the front bulkhead with three wireties.
17. Pull out on the right front inner fender, and remove
the vehicle ground bolt from the right front sideframe. Secure the ground terminal of the fog lightharness with this ground bolt.
18. Secure the fog light harness to the vehicle harnesswith two wire ties. Do not secure the fog light
harness to the SRS harness.
19. Secure the fog light harness to the hole in the rightlower cross member with one wire tie.
20. Pull out on the left front inner fender, and securethe fog light harness to the vehicle harness with
three wire ties.
21. Secure the fog light harness to the hole in the leftlower cross member and to the vehicle harness
with one wire tie.
4216020Y
WIRE TIES
RIGHT FRONTSIDE FRAME
FOG LIGHTHARNESS
LOWER CROSSMEMBER HOLE
WIRE TIE
VEHICLEGROUND BOLT(Reused)
RIGHTFRONTINNERFENDER
FOG LIGHT HARNESSGROUND TERMINAL
(Secure the terminal tothe body ground atthe front of the car.)
SRSHARNESS(YELLOW)
4216030Y
LEFT
FRONTINNERFENDER
FOG LIGHTHARNESS
WIRE TIEWIRE TIE
LOWER CROSSMEMBER HOLE
-
7/31/2019 2006 Rsx Fog Lights
6/15
6 of 15 AII 30236 (0507) 2005 American Honda Motor Co., Inc - All Rights Reserved.
Installing the Fog Lights
22. Position the left bracket and left subbracket onthe left fog light, and install two stepped screws
(one for each) and one 4 x 18 mm washer-screw.Check the identification mark on the brackets
(R: right, L: left).
23. Slide four spring nuts onto the opening at the left
side of the front bumper.
24. Pull out the fog light harness 2-pin connector and
plug it into the left fog light. Position the left foglight on the front bumper, and install three
5 x 16 mm washer-screws and one 5 x 12 mmwasher-bolt.
25. Repeat steps 22 thru 24 on the right side to installthe right fog light.
26. Install the tab on the outboard side of the left fog
light trim into the slot in the front bumper.
27. Insert one 5 x 16 mm washer-screw into the hole
in the left fog light trim in the position shown, andsecure the trim with one lock washer from thereverse side.
28. Repeat steps 26 and 27 on the right side to install
the right fog light trim.
Routing the Fog Switch Harness
29. Inside the vehicle, turn the two knobscounterclockwise, and remove the driversdashboard lower cover (two retaining tabs and twohooks).
4216041Y
4 x 8 mmWASHER-SCREW
LEFT
BRACKET
LEFTSUBBRACKET
STEPPEDSCREW
LEFTFOGLIGHT
STEPPEDSCREW
4216060Y
LOCKWASHER
LEFT FOGLIGHT TRIM FRONTBUMPER
5 x 16 mmWASHER-SCREW
4216051Y
FRONTBUMPER
WASHER-SCREWS,5 x 16 mm (3)
LEFT
FOG LIGHT5 mmWASHER-BOLT
FOG LIGHT HARNESS2-PIN CONNECTOR
SPRINGNUTS (4)
DRIVERSDASHBOARDLOWER COVER
KNOB
RETAININGTABS (2)
HOOKS(2)
-
7/31/2019 2006 Rsx Fog Lights
7/15
2005 American Honda Motor Co., Inc - All Rights Reserved. AII 30236 (0507) 7 of 1
TRIM RING
RETAININGTAB (4)
CENTERCONSOLE
BOOT
SHIFT KNOB
PLASTICCLIP
30. Turn the knob clockwise, and remove the drivers
dashboard under cover from the holder (one clip).
31. Pull the center lower cover toward you to release
the one retaining tab and six clips.
33. On M/T vehicles, push the boot down while
holding the plastic clip. Remove the shift knob byturning it counterclockwise.
34. On A/T vehicles, remove the trim ring from thecenter console (four retaining tabs).
4602010Y
HOLDER
DRIVERSDASHBOARDUNDER COVER
CLIP
KNOB
32. Unplug the vehicle 2-pin connector from the
accessory socket, and remove the center lowercover.
CENTER LOWER
COVER
CLIPS (6)
RETAINING TAB
ACCESSORYSOCKET
VEHICLE 2-PIN
CONNECTOR
-
7/31/2019 2006 Rsx Fog Lights
8/15
8 of 15 AII 30236 (0507) 2005 American Honda Motor Co., Inc - All Rights Reserved.
35. Remove the center console trim by lifting it
upward to release the six clips and one retainingtab.
36. Remove the two self-tapping screws that fasten
the center console.
37. Remove the beverage holder by lifting it upward to
release the four clips.
BEVERAGEHOLDER
CLIPS (4)
CENTERCONSOLE
CENTERCONSOLETRIM
RETAININGTAB
CLIPS (6)
CENTERCONSOLE
SELF-TAPPINGSCREW
-
7/31/2019 2006 Rsx Fog Lights
9/15
2005 American Honda Motor Co., Inc - All Rights Reserved. AII 30236 (0507) 9 of 1
SWITCH
COVER(Discard.)
RETAININGTABS (2)
INSTRUMENT PANEL
A/T Vehicles:
39. Release the two clips that secure the front of the
center console, then disconnect the vehicle 2-pinconnector from the accessory socket by first
sliding the center console toward the rear, thenlifting it upward. On A/T models, remove the
covers at the front of the center console (oneself-tapping screw for each cover).
40. Remove the two self-tapping screws and one
screw, and remove the steering column upper andlower covers (six retaining tabs).
41. From behind the instrument panel, remove the
right switch cover (two retaining tabs).
38. Inside the center console, remove the two clips.
At the rear of the center console, remove the twoscrews.
M/T Vehicles:
STEERINGCOLUMNLOWERCOVER
SELF-TAPPINGSCREW
STEERING COLUMNUPPER COVER
RETAINING TABS (6)
SCREW
Pushin.
SCREWS (2)
CLIPS (2)
CENTERCONSOLE
SELF-TAPPINGSCREW
VEHICLE 2-PINCONNECTOR
ACCESSORYSOCKET
CLIPS
COVER(Remove.)
SCREWS (2)
CLIPS (2)
CLIP
CENTERCONSOLE
ACCESSORYSOCKET
VEHICLE 2-PINCONNECTOR
-
7/31/2019 2006 Rsx Fog Lights
10/15
10 of 15 AII 30236 (0507) 2005 American Honda Motor Co., Inc - All Rights Reserved.
4415070Y
FUSE BOX
VEHICLE 6-PINCONNECTOR(A/T Vehicles only)
SWITCH HARNESS1-PIN CONNECTOR(WHT/RED WIRE)
SWITCHHARNESS 6-PINCONNECTORS
SWITCHHARNESS
FUSE BOX
Location of 6-pin Connector
BOLT
Location of 1-pinConnector
DUMMYCONNECTOR(Discard.)
If the vehicle is equipped with an optional cigarette
lighter, plug the switch harness 6-pin connector into thecigarette lighter 6-pin connector.
43. Unplug the vehicle 6-pin connector from the fusebox, then plug the 6-pin connector of the switch
harness there. Plug the 1-pin connector (WHT/RED wire) of the switch harness into the fuse box
as indicated. On M/T vehicles, there is no 6-pinconnector plugged into the fuse box.
44. On A/T vehicles, locate the 6-pin connector taped
to the switch harness, and remove the dummyconnector from that connector. Plug the vehicle
6-pin connector you just unplugged from the fusebox into that connector.
45. Reinstall the fuse box.
46. Locate the 1-pin connector blue-taped to the vehicleharness in front of the fuse box, and remove the
blue tape to free the connector. Plug the remaining1- pin connector of the switch harness into this1-pin connector. Then, secure the 1-pin connector to
the vehicle harness with one wire tie.
47. Route the 5-pin connector of the switch harnessunder the steering shaft to the switch opening inthe instrument panel.
48. Route the terminal end of the switch harness to the
top of the steering column along the vehicle harness.
42. Remove the bolt that secures the fuse box, and
lower the fuse box.
CIGARETTE LIGHTERHARNESS
SWITCHHARNESS
FUSE BOX 6-PINCONNECTOR
4623010Y
SWITCH HARNESS 5-PINCONNECTOR(Route to the switch lid opening.)
VEHICLEHARNESS
SWITCH HARNESS1-PIN CONNECTOR
BLUETAPE
VEHICLE HARNESS1-PIN CONNECTOR
FUSEBOX
SWITCHHARNESS
WIRE TIESTEERINGSHAFT
TERMINAL END ofSWITCH HARNESS(Route to the top ofthe steering column.)
-
7/31/2019 2006 Rsx Fog Lights
11/15
2005 American Honda Motor Co., Inc - All Rights Reserved. AII 30236 (0507) 11 of 1
4415080Y
SWITCH HARNESS12-PIN CONNECTORS
VEHICLEHARNESS WIRE TIE
VEHICLEHARNESS12-PINCONNECTORS
SWITCHHARNESS
CENTERCONSOLEOPENING
VEHICLE HARNESS12-PIN CONNECTOR
WIRETIE
VEHICLEHARNESS
49. Above the steering column, disconnect the vehicle
16-pin connectors. Remove the retainer, and insertthe switch harness terminal into the 16-pinconnector at the location shown. Reinstall the
retainer.
50. Reconnect the vehicle 16-pin connector.
51. Route the switch harness 12-pin connector to the
center console opening alongside the vehicleharness.
52. At the center console opening, unplug the vehicle
12-pin connector.
53. Connect the vehicle harness 12-pin connectors tothe switch harness 12-pin connectors.
54. Secure the switch harness to the vehicle harnesswith two wire ties in the areas shown.
RETAINERVEHICLE 16-PINCONNECTOR
SWITCH HARNESSTERMINAL(Insert into the 16-pinconnector with thestaked side facingdown.)
SWITCHHARNESS
TERMINAL(for connecting theterminal of theswitch harness)
As Viewed fromthe Harness Side
-
7/31/2019 2006 Rsx Fog Lights
12/15
12 of 15 AII 30236 (0507) 2005 American Honda Motor Co., Inc - All Rights Reserved.
SWITCH
INSTRUMENTPANEL
SWITCH
HARNESS5-PINCONNECTOR
55. Attach the fuse label (20A) to the switch harness
fuse case.
59. Plug the switch harness 5-pin connector into the
rear of the switch.
60. Install the switch into the instrument panel.
61. Check that all wire harnesses are routed properly
and all connectors are plugged in.
62. Reinstall all removed parts.
63. Reconnect the negative cable to the battery, and
reset the radio station presets.
NOTE: Whenever the battery is disconnected, the
drivers window AUTO function is disabled.
64. Start the engine. Push down on the driverswindow switch until the window is fully open.
65. Pull up on the drivers window switch to close thewindow completely, then hold the switch for two
seconds.
66. Lower and raise the driver's window to check thewindow AUTO function.
4415090Y
RELAY
STEERING HANGERBEAM
SWITCH HARNESS
FUSE CASE FUSE LABEL(20A)
SWITCHHARNESS
6 mmWASHER-BOLT
SWITCHHARNESS4-PINCONNECTOR
56. Position the relay on the steering hanger beam,
and install the 6 mm washer-bolt. Plug the switchharness 4-pin connector into the relay.
57. Pull the switch harness 5-pin connector outthrough the instrument panel.
58. Secure the switch harness to the vehicle harnesswith seven wire ties in the areas shown.
4415101Y
WIRE TIE
SWITCHHARNESS
VEHICLEHARNESS
SWITCHHARNESS5-PIN
CONNECTOR
WIRE TIE
WIRE TIE
-
7/31/2019 2006 Rsx Fog Lights
13/15
2005 American Honda Motor Co., Inc - All Rights Reserved. AII 30236 (0507) 13 of 1
4216100Y
SCREW
TABTRIM
4216110Y
WASHERSCREW
FOG LIGHT WASHER-BOLT
CONNECTOR
USE AND CARE
How to Operate the Fog Lights
Turn the light switch to the position(headlights on low beam).
Press the fog light switch (indicator is on).
NOTE: The fog light lenses can cloud when the
outside temperature is cold; this is normal and shouldgo away in warm weather.
Fog Light Aiming Adjustment
1. Adjust the fog lights:
Adjust the aiming according to local laws and
regulations.
To adjust, turn the aiming adjustment screw
clockwise or counterclockwise until the correctaiming is obtained.
Bulb Replacement
1. Loosen the screw, and remove the left trim (onetab).
2. Remove the three washer-screws and one washer
bolt, and pull the fog light toward you. Unplug theconnector, and remove the fog light.
WASHERSCREW
4216090Y
AIMINGADJUSTMENTSCREW
To raise.
To lower.
PHILLIPSSCREWDRIVER
-
7/31/2019 2006 Rsx Fog Lights
14/15
14 of 15 AII 30236 (0507) 2005 American Honda Motor Co., Inc - All Rights Reserved.
3. Remove the bulb from the fog light by turning it
counterclockwise and pulling it toward you.
4. Install the new bulb into the fog light:
Use only a Honda halogen light bulb ofspecified wattage.
Rating: 12V 55W H11 Halogen Light Bulb
Do not touch the bulb. Oily or greasy
substances on the bulb could shorten itsservice life due to the heat produced when thebulb is turned on. If the bulb is accidentally
touched, wipe it clean with a clean, soft cloththat has been dampened with denatured
alcohol or a mild detergent solution.
5. Reinstall the fog light in the reverse order ofremoval:
Check that the wire harnesses are not pinched.
Make sure you tighten the self-tapping screwssecurely.
4216120YBULB
FOG LIGHT
4216130Y
FOG LIGHT
BULB
-
7/31/2019 2006 Rsx Fog Lights
15/15
2005 American Honda Motor Co Inc All Rights Reserved AII 30236 (0507) 15 of 1
LIGHT SWITCH
OFFLow Hi
OFF
ON ONFOGLI
GHT
SWITCH
B
Y
L
G
R
W
BR
O
SB
LG
P
GR
BLACK
YELLOW
BLUE
GREEN
RED
WHITE
BROWN
ORANGE
SKY BLUE
LIGHT GREEN
PINK
GRAY
SMALLRELAY
COMBINATIONLIGHT SWITCH
LIGHTINGSWITCH
PASSING
DIMMER
R/W
R/L B B
L/R
W/G
BATTERY 100A
15A
20A
R/Y RIGHT LEFT
HEADLIGHT
HILOW HILOW
20A
LIGHTINGRELAY
30AW/R
20AR/Y
R/BR/L
L/Y
FOGLIGHTRELAY
FOGLIGHTS
B
FOGLIGHTSWITCH
R
CIRCUIT DIAGRAM