Accessories Material Specification
1000.0000-Td-0701_rev0
Page 1 of 2
ACCESSORIES MATERIAL SPECIFICATION
Accessory Component Material Quality Standard Treatment Sketch
Fender Anchorage. Old Concrete
Bolt Nut “L” Washer
DIN-975 DIN-934
-
4.8 5
S275JR
EN-ISO 848-1 EN-ISO 848-2
-
HDG (1)
ISO 1461:2009
Bolt DIN -933 4.8 EN-ISO 848-1
Threaded Socket - S355JR EN 10025
Round - S355JR EN 10025
Fender Anchorage. New Concrete
Plate “L” Washer
- -
S275JR S275JR
EN 10025 -
HDG (1)
ISO 1461:2009
Chain Anchorage. Old Concrete U Round - S275J2 EN 10025
HDG (1)
ISO 1461:2009
U Round - S275J2 Chain Anchorage. New Concrete Plate - S275JR
EN 10025
HDG (1)
ISO 1461:2009
Plate - S275JR EN 10025
Bolt DIN-975 4.8 EN-ISO 848-1
Nut DIN-934 5 EN-ISO 848-2
Chain anchorage bracket
Washer DIN-125 BC -
HDG (1)
ISO 1461:2009
Round - S275J2 EN 10025
Plate - S275JR EN 10025 Tensor
Nut DIN-934 5 EN-ISO 848-2
HDG (1)
ISO 1461:2009
L Washer Plate - S275JR EN 10025
HDG (1)
ISO 1461:2009
Bolt DIN-933 4.8 EN-ISO 848-1
Nut DIN-934 5 EN-ISO 848-2 Fender Bolts
Plain Washer DIN-125 BC -
HDG (1)
ISO 1461:2009
Bolt DIN-933 4.8 EN-ISO 848-1
Nut DIN-934 5 EN-ISO 848-2 Polythene Botls
Plain Washer DIN-125 BC -
HDG (1)
ISO 1461:2009
Bolt DIN-931 4.8 EN-ISO 848-1
Nut DIN-934 5 EN-ISO 848-2 Chain bolts
Plain Washer DIN-125 BC -
HDG (1) ISO 1461:2009
Accessories Material Specification
1000.0000-Td-0701_rev0
Page 2 of 2
(1) GALVANIZING THICKNESS REQUIREMENT
Accessory Standard Applied Galvanizing Process Local
Thickness Required
Average Thickness Required
Fender Anchorages Thread Rod ISO 1461:2009 Not Centrifuged 70 µm 85 µm
Chain Anchorages U configuration ISO 1461:2009 Not Centrifuged 70 µm 85 µm
Chain Anchorages Bracket configuration ISO 1461:2009 Not Centrifuged 70 µm 85 µm
Tensors ISO 1461:2009 Not Centrifuged 70 µm 85 µm
Shackles ISO 1461:2009 Not Centrifuged 70 µm 85 µm
Chains ISO 1461:2009 Not Centrifuged 70 µm 85 µm
Shaft for cylindrical fenders ISO 1461:2009 Not Centrifuged 70 µm 85 µm
Fender anchorages ISO 1461:2009 Centrifuged 40 µm 50 µm
Bolts ISO 1461:2009 Centrifuged 40 µm 50 µm
Nuts ISO 1461:2009 Centrifuged 40 µm 50 µm
Plain Washers ISO 1461:2009 Centrifuged 45 µm 55 µm
L Washers ISO 1461:2009 Centrifuged 45 µm 55 µm
NOTE:
- Issue of 2.1 certificate according UNE-EN-ISO 10204. - Any other tests to consider, beyond those mentioned here, is optional at extra cost.
It is not allowed to reproduce, photocopy, scan or copy this document or part of this document without the previous written authorization of the manufacturer. Due to our politics of improvement and constant development, all the technical information of this document is subject to changes without previous notice. This document has been realized by the major care, nevertheless the manufacturer does not assume any responsibility of any mistake in this document
Accessory Component Material Quality Standard Treatment Sketch
Dee Shackle Standard Shackle
DIN 82101 A Type - HDG (1)
ISO 1461:2009
Chain Chain DIN-764 GRADO 2 Without stud link - HDG (1)
ISO 1461:2009
Shaft for cylindrical Fender Round - S355JR EN 10025 HDG (1)
ISO 1461:2009