Download - BINOSPEC METROLOGY
![Page 1: BINOSPEC METROLOGY](https://reader033.vdocuments.net/reader033/viewer/2022061615/568162b3550346895dd33cce/html5/thumbnails/1.jpg)
BINOSPEC METROLOGY
Alex Gary
![Page 2: BINOSPEC METROLOGY](https://reader033.vdocuments.net/reader033/viewer/2022061615/568162b3550346895dd33cce/html5/thumbnails/2.jpg)
Astronomical spectrograph for the MMT Observatory on Mount Hopkins in Arizona
2007- project design completed by Harvard University
Used extensively by the University of Arizonaand other institutions
Binospec
![Page 3: BINOSPEC METROLOGY](https://reader033.vdocuments.net/reader033/viewer/2022061615/568162b3550346895dd33cce/html5/thumbnails/3.jpg)
Binospec is an imaging spectrograph with dual 8'x15' fields of view
dual slitmasks which can hold up to 150 slitlets for multiobject spectroscopy.
Superior sky subtraction with these slitlets will allow Binospec to reach 3-4 magnitudes deeper than Hectospec
Binospec uses the fiber spectroscopy configuration of the corrector, which has built-in atmospheric dispersion compensation.
Binospec
![Page 4: BINOSPEC METROLOGY](https://reader033.vdocuments.net/reader033/viewer/2022061615/568162b3550346895dd33cce/html5/thumbnails/4.jpg)
In order to allow the design to work with so many slitlets a callibration screen was necessary in order to assure proper viewing.
This is the specific part of the assembly that I was involved in.
Calibration Screen
![Page 5: BINOSPEC METROLOGY](https://reader033.vdocuments.net/reader033/viewer/2022061615/568162b3550346895dd33cce/html5/thumbnails/5.jpg)
As the project came to fruition a precise method of measuring and checking key points and joints in the connecting structures was essential
Between manufacturing and assembly, metrology is required to troubleshoot any problems that may come up during assembly before assembly begins
As parts come in for assembly they were measured and compared to nominal coordinates to determine any problems or complications
The Metrology Stage
![Page 6: BINOSPEC METROLOGY](https://reader033.vdocuments.net/reader033/viewer/2022061615/568162b3550346895dd33cce/html5/thumbnails/6.jpg)
The Metrology process involved a FARO Arm and CAM 2 Measure 10 Software.
The entire process of metrology involved a 3-Stage Process.
The Three Stages to the Metrology involved Set Up, Measurement, and Analysis.
Metrology Technique
![Page 7: BINOSPEC METROLOGY](https://reader033.vdocuments.net/reader033/viewer/2022061615/568162b3550346895dd33cce/html5/thumbnails/7.jpg)
Set up involves both physical and virtual set up.
The piece to be measured had to strategically mounted to get all of the required measurements
A solid works model was uploaded to the CAM 2 Software and the desired planes and circles had to be selected before measurement could begin
Set Up
![Page 8: BINOSPEC METROLOGY](https://reader033.vdocuments.net/reader033/viewer/2022061615/568162b3550346895dd33cce/html5/thumbnails/8.jpg)
Cover 5
![Page 9: BINOSPEC METROLOGY](https://reader033.vdocuments.net/reader033/viewer/2022061615/568162b3550346895dd33cce/html5/thumbnails/9.jpg)
•FARO Arm •Solid Works Model (Before Set Up)
•Model in CAM 2 Software (Post Set Up)
Set Up (Physical and Virtual)
![Page 10: BINOSPEC METROLOGY](https://reader033.vdocuments.net/reader033/viewer/2022061615/568162b3550346895dd33cce/html5/thumbnails/10.jpg)
After Set Up is complete measurements can be taken with the FARO Arm. It is a rather simple process but involves attention to detail and care to make sure no simple mistakes are made.
Measurement
![Page 11: BINOSPEC METROLOGY](https://reader033.vdocuments.net/reader033/viewer/2022061615/568162b3550346895dd33cce/html5/thumbnails/11.jpg)
Analysis involves comparing the actual and nominal measurements, determining sources of error in either manufacturing or the measurement stage, and deciding on actions to be take on any error found.
Actions taken during the analysis stage can range from returning to the measurement stage, making slight modifications ourselves, or returning the entire part to the manufacturer.
Analysis
![Page 12: BINOSPEC METROLOGY](https://reader033.vdocuments.net/reader033/viewer/2022061615/568162b3550346895dd33cce/html5/thumbnails/12.jpg)
CAM 2 Software allows does some of the analysis on its own. This is a sample of the analysis for the handling cart interface. This crucial part had to be precisely manufactured so every plane and circle was analyzed with scrutiny (and passed)
Analysis Sample
![Page 13: BINOSPEC METROLOGY](https://reader033.vdocuments.net/reader033/viewer/2022061615/568162b3550346895dd33cce/html5/thumbnails/13.jpg)
After a week and a half of Metrology we found no crucial problem so we began assembly. The entire frame assembly was simple with only one minor modification needed.
Beyond this the internal structure of the Calibrator Screen and Derotator Assembly had to be completed.
Recently other metrology and engineering decisions had to be made to make assembly run smoother
Overall Summer Metrology Results
![Page 14: BINOSPEC METROLOGY](https://reader033.vdocuments.net/reader033/viewer/2022061615/568162b3550346895dd33cce/html5/thumbnails/14.jpg)
Directions vs Reality
![Page 15: BINOSPEC METROLOGY](https://reader033.vdocuments.net/reader033/viewer/2022061615/568162b3550346895dd33cce/html5/thumbnails/15.jpg)
BINOSPEC TEAM