FT SB 08
TECHNICALSHEET
FOGLIO TECNICO
FEUILLETECHNIQUE
TECHNISCHE HANDLEIDING
GBI F NL
GROUP S.P.A.
Chiamata digitale Art. 3340 Digital call Art. 3340
Appel numérique Art. 3340Digitale oproepmodule, Art. 3340
01-2006
Avvertenze: • Effettuare l’installazione seguendo scrupolosamente le istruzioni fornite dal costruttore ed in conformità alle norme vigenti.• Tutti gli apparecchi devono essere destinati esclusivamente all’uso per cui sono stati concepiti. Comelit Group S.p.A. declina ogni responsabilità
per un utilizzo improprio degli apparecchi, per modifiche effettuate da altri a qualunque titolo e scopo, per l’uso di accessori e materiali non originali.• Tutti i prodotti sono conformi alle prescrizioni delle direttive CEE 73/23-89/336 e ciò è attestato dalla presenza della marcatura CE sugli stessi.• Evitare di porre i fili di montante in prossimità di cavi di alimentazione (230/380V).
Instructions:• Install the equipment by carefully following the instructions given by the manufacturer and in compliance with the legislation in force.• All the equipment must only be used for the purpose it was built for. Comelit Group S.p.A. declines any responsibility for improper use of the
apparatus, for modifications made by others under any title or scope, and for the use of accessories and materials which are not the original ones.• All the products comply with the requirements of the EEC 73/23-89/336 directives. This is proved by the CE mark on the products .• Do not run the riser wires in proximity of the power supply cables (230/380V).
Instructions • Effectuer l’installation en suivant scrupuleusement les instructions fournies par le constructeur et conformément aux normes en vigueur.• Tous les appareils doivent être strictement destinés à l’emploi pour lequel ils ont été conçus. Comelit Group S.p.A. décline toute responsabilité
en cas de mauvais usage des appareils, pour des modifications effectuées par d’autres personnes pour n’importe quelle raison et pour l’utilisation d’accessoires non fournis par nous.
• Tous les produits sont conformes aux prescriptions demandées par les normes CEE 73/23-89/336. Cela est attesté par la présence du marqueCE sur les produits.
• Eviter de placer les fils de montant à proximité des câbles d’alimentation (230/380 V).
Waarschuwingen• Volg de instructies van de fabrikant nauwkeurig en installeer de materialen volgens de plaatselijk geldende normen en wetgeving.• Alle componenten mogen alleen gebruikt worden voor de doeleinden waarvoor ze zijn ontworpen. Comelit Group S.p.A. is niet verantwoordelijk bij
een onjuist gebruik van de apparatuur, of modificaties welke aangebracht zijn zonder voorafgaande toestemming, evenals het gebruik van accessoireswelke niet door de fabrikant zijn aangeleverd.
• Alle producten voldoen aan de eisen van de richtlijn EEC 73/23-89/336. Die wordt bevestigd door het CE label op de producten.• Monteer de aders (bekabeling) niet in de nabijheid van voedingskabels (230/380V).
I
GB
F
NL
FT SB 08
GROUP S.P.A.
FT SB 08
1 FT SB 08
Disporre tassativamente i moduli come indicato in figura.
Arrange the modules only as indicated in the following drawing.
Positionner les modules seulement comme indiqué dans le dessin suivant.
Plaats de modulen alleen in de volgorde zoals getoond in onderstaand figuur.
I
GB
F
NL
GROUP S.P.A.
FT SB 08 2
• INTRODUZIONE pag. 3
• 1) FUNZIONE DEI TASTI pag. 3
• 2) INSTALLAZIONE DEL MODULO pag. 4
• 3) IMPOSTAZIONE DELLA LINGUA pag. 4
3A) Prima accensione del modulo, la lingua non e’ ancora stata selezionata pag. 4
3B) Modifica della lingua precedentemente impostata pag. 4
• 4) AUTO – DIAGNOSI pag. 4
• 5) USO DELLA RUBRICA PORTANOMI pag. 5
5A) Scorrimento e chiamata dell’utente selezionato pag. 5
5B) Ricerca di un nome all’interno della rubrica pag. 5
• 6) USO DEL MODULO DI CHIAMATA pag. 6
• 7) GESTIONE DELLA RUBRICA pag. 6
7A) Inserimento di un nome pag. 6
7B) Inserimento tramite art. 1230 pag. 6
7C) Inserimento tramite software art. 1231/6D pag. 7
7D) Inserimento tramite software art. 1249 pag. 7
7E) Inserimento direttamente da tastiera pag. 8
7F) Modifica di un nome pag. 8
7G) Cancellazione di un nome pag. 9
7H) Cancellazione di un nome tramite Art.1230 pag. 10
7I) Cancellazione di tutti i nomi presenti in rubrica pag. 10
7L) Visualizzazione del numero di nomi inseriti in rubrica,
della versione software installata e del Codice ID pag. 10
• 8) IMPOSTAZIONE DELLA MODALITA’ DI FUNZIONAMENTO
(STANDARD OPPURE CODICE INDIRETTO) pag. 11
8A) Modalita’ di chiamata standard pag. 11
8B) Modalita’ di chiamata codice indiretto pag. 11
• 9) MODIFICA DEI PARAMETRI D’IMPIANTO pag. 12
9A) Impostazione dei parametri del porter art.1602-4660
(tempo di apriporta ,tempo di fonica e tempo di attesa reset) pag. 12
9B) Visualizzazione dei parametri del porter art.1602 – 4660
(tempo di apriporta , di fonica e di attesa reset ) pag. 12
9C) Impostazione del Codice ID pag. 13
• 10) GESTIONE DELLA FUNZIONE DI CONTROLLO ACCESSI pag. 13
10A) Supercodice di default pag. 13
10B) Modifica del supercodice pag. 13
10C) Azzeramento del supercodice pag. 14
10D) Inserimento di un codice password pag. 14
10E) Cancellazione di un codice password pag. 14
10F) Cancellazione di tutti i codici di password pag. 15
10G) Ricerca di un codice di password pag. 16
10H) Attivazione del rele’ di apriporta digitando il codice di password pag. 16
10I) Visualizzazione del numero di password inserite pag. 17
• 11) IMPOSTAZIONE DEL TIPO DI CONNESSIONE
CON PC, RS232 OPPURE RS485 pag. 17
SOMMARIO
FT SB 08
3 FT SB 08
ITA
LIA
NO
Il modulo di chiamata digitale Comelit Art.3340 è utilizzabile in impianti tipo Simplebus,
è dotato di una rubrica portanomi per memorizzare una lista di nomi utente e di una
tastiera alfanumerica per chiamare gli utenti citofonici componendo il codice che li
identifica.
Le principali caratteristiche sono:
• Capienza della memoria: 400 nomi da 18 caratteri alfanumerici.
• Display grafico con risoluzione 128x64 dots/pitch.
• 2 modalità di gestione della chiamata : Standard oppure Codice Indiretto .
• Inserimento della lista di nomi ( Download ) tramite programmatore Art.1230 oppure
tramite connessione con PC dotato di software Art.1231/6D oppure Art.1249.
• L’inserimento dei nomi tramite connessione con PC può avvenire su linea RS232
oppure su linea RS485 mediante la scheda di interfaccia Art.1319 ( vedi schema di
impianto CA_EN_108 ).
• Lettura ( Upload ) della lista di nomi memorizzata nel modulo rubrica mediante
connessione con PC dotato di software Art.1249.
• Controllo Accessi con la possibilità di memorizzare fino a 300 codici password per
attivare il relè presente nel modulo porter,tipicamente utilizzato come apriporta.
• Possibilità di visualizzare i messaggi dell’interfaccia grafica in una delle 9 lingue
disponibili.
1) FUNZIONE DEI TASTIINTRODUZIONE
CHIAMATA – SELEZIONA MENU
INDIETRO: Scorre la lista degli utenti in ordine alfabetico decrescente
AVANTI: Scorre la lista degli utenti in ordine alfabetico crescente.
RICERCA NOME - ESCI DAL MENU
CHIAMATA – APRIPORTA LOCALE
CANCELLAZIONE CARATTERE o CHIAMATA
GROUP S.P.A.
FT SB 08 4
CONDIZIONE INIZIALE
3) IMPOSTAZIONE DELLA LINGUA
3A) ALLA PRIMA ACCENSIONE DEL MODULO, LA LINGUA NON E’ ANCORA STATA SELEZIONATA:
3B) MODIFICA DELLA LINGUA PRECEDENTEMENTE IMPOSTATA:
Scorrere la lista con i tasti ▲▼.Per selezionare la linguadesiderata premere .
Modulo alimentato.
* ITALIANOENGLISH
FRANCAIS
La voce DEFAULT impostala lingua italiana, alla successiva riaccensionedel modulo vienenuovamente richiesta laselezione della lingua.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
CONDIZIONE INIZIALE
Modulo alimentato conmorsetto PR collegato almorsetto - .
Il modulo è in fase di programmazione:
per selezionare il menu▲▼per scorrere i menu
per tornare al menu precedente.
SELECT LANGUAGE:* ITALIANOENGLISH
TEST DESCRIZIONE
4) AUTO – DIAGNOSI
All’accensione l’apparecchiatura esegue una diagnosi delle connessioni per verificare la corretta comunicazione con il modulo porter ART.1602/4660 e con il modulo tastiera che compone l’ART. 3340. Se accanto alla voce appare la scritta OK il test è positivo,viceversa seappare la scritta FALLITA. Alla fine della fase di auto – diagnosi premere il tasto ▼per portareil modulo nello stato di riposo. Di seguito la tabella che riassume il significato dei singoli test:
2) INSTALLAZIONE DEL MODULO
Attenersi a quanto riportato sul foglio tecnico FT/SB/07 oppure MT/SB2/02 per il cablag-gio del modulo Art. 3340. Per evitare disturbi causati da scariche elettrostatiche, si consi-glia di eseguire una schermatura della carcassa come riportato sullo schema a pagina 74.
INIZIALIZZAZIONE
SERIALE PORT.
MODALITA’
Verifica la corretta scrittura della EEPROM che contiene lalista dei nomi utente. Se il test fallisce il modulo è guasto.
Se il test fallisce occorre verificare la corretta connessioneseriale con il modulo porter. Art.1602 / 4660.
Verifica la presenza della tastiera alfanumerica che compone l’Art.3340. Se appare la scritta 3342 accantoalla descrizione, bisogna verificare la corretta connessionetra la tastiera alfanumerica e il modulo rubrica.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
SCEGLI LINGUA* ITALIANO
INGLESE
SCEGLI LINGUAITALIANO
* INGLESE
La lingua impostata ècontraddistinta da un asterisco sul fianco sinistro.La voce DEFAULT imposta la lingua italiana, allasuccessiva riaccensione del modulo vienenuovamente richiesta laselezione della lingua.
Selezionare il menuIMPOSTAZIONI / SCEGLI LINGUA.
Scorrere la lista con i tasti ▲▼.Per selezionare la linguadesiderata premere .
GESTIONE RUBRICACONTROLLO ACCESSI
IMPOSTAZIONI
FT SB 08
5 FT SB 08
ITA
LIA
NO
CONDIZIONE INIZIALE
5) USO DELLA RUBRICA PORTANOMI
5A) SCORRIMENTO E CHIAMATA DELL’UTENTE SELEZIONATO
Scorrere la lista dei nomiutente con i tasti ▲▼.Per uscire premere il tasto .
Premere il tasto per chiamare l’utente selezionato.
E’ possibile annullare la chiamata o la conversazione in corso premendo il tasto X.
Modulo alimentato in condizione di riposo.
Se sono stati memorizzatidegli utenti in rubrica.
GIOVANNI ROSSI I nomi sono inseriti in ordine alfabetico.
La chiamata è avvenutacorrettamente.
La chiamata non è avvenuta correttamente.
L’impianto è occupato.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
DIGITA IL CODICE UTENTE
Seguito da:
SCORRI NOMI CERCA NOME
CONDIZIONE INIZIALE
5B) RICERCA DI UN NOME ALL’INTERNO DELLA RUBRICA
Premere il tasto .
Inserire il nome utente anchecon parte dell’estensione.ESEMPIO: ROSSI
Premere il tasto periniziare la ricerca.
Ora è possibile scorrere la lista dei nomi utente con i tasti ▲▼.
Modulo alimentato in condizione di riposo.
INSERIRE IL NOME CHE SI DESIDERA
RICERCARE
ROS_
RICERCA IN CORSO…
ROSSI GIOVANNI
Oppure:
IL NOME NON E’ PRESENTE IN RUBRICA
Viene visualizzato il nomeutente trovato.
Il nome utente non esiste.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
SCORRI NOMI CERCA NOME
Seguito da:
DIGITA IL CODICE UTENTE
CHIAMATA INOLTRATA
Oppure:
UTENTE NON DISPONIBILE
Oppure:
UTENTE OCCUPATO
CHIAMATA INOLTRATA
Oppure:
IN COMUNICAZIONE
GROUP S.P.A.
FT SB 08 6
CONDIZIONE INIZIALE
6) USO DEL MODULO DI CHIAMATA
ESEMPIO: Si vuole chia-mare l’utente con codice 1. Premere il tasto 1 dallatastiera alfanumerica.
Premere il tasto oppure per chiamare.
E’ possibile annullare la chiamata o la conversazione in corsopremendo il tasto X.
Modulo alimentato in condizione di riposo.
CHIAMA UTENTE:_ _ 1
CHIAMATA INOLTRATAOppure:UTENTE
NON DISPONIBILEOppure:
UTENTE OCCUPATO
CHIAMATA INOLTRATA Oppure:
IN COMUNICAZIONE
La chiamata è avvenutacorrettamente.La chiamata non è avvenutacorrettamente.
L’impianto è occupato.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
SCORRI NOMI CERCA NOME
Seguito da:DIGITA IL CODICE
UTENTE
CONDIZIONE INIZIALE
7B) INSERIMENTO TRAMITE ART. 1230 (non disponibile se la modalità di chiamata è Codice Indiretto; vedi Punto 8)
Premere il tasto NAME->dell’Art.1230.
Digitare il nome utente che si vuole inserire.ESEMPIO: ROSSI GIOVANNI
Premere il tasto ENTERdell’Art.1230.
Modulo alimentato in condizione di riposo.
Se sono stati memorizzatidegli utenti in rubrica.
INSERIMENTO DIUN NOME
ROSSI GIOVANNI
CODICE: _ _ _
Per utilizzare il caratteri inferioredei tasti premere SHIFT. Per cancellare il carattere a sinistra premere < . Per inserire caratteri particolaripremere la combinazione di tasti come descritto sotto:NAME -> + A = ÅNAME -> + B = ÄNAME -> + C = ßNAME -> + O = ÖNAME -> + P = ØNAME -> + Q = ÜPremere ESC per annullarel’operazione di inserimentodel nome utente.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
DIGITA IL CODICE UTENTE
Seguito da:SCORRI NOMI CERCA NOME
7) GESTIONE DELLA RUBRICA
7A) INSERIMENTO DI UN NOME E’ possibile memorizzare un nome all’interno della rubrica tramite programmatore infra-rossi ART.1230, oppure tramite i software ART.1231/6D - ART.1249, oppure direttamen-te tramite la tastiera alfanumerica di cui è dotato il modulo.
FT SB 08
7 FT SB 08
ITA
LIA
NO
CONDIZIONE INIZIALE
7C) INSERIMENTO TRAMITE SOFTWARE ART. 1231/6D
Avviare il softwareArt.1231/6D. I settagli richiestidal software sono:- Caricare il database che
contiene nomi e codici utente.- Selezionare la modalità
COMPATIBILE dal menuSCARICAMENTO.
- Selezionare la porta COM.Premere il pulsante SCARICAMENTO.
Alla fine del download.
Modulo alimentato in condizionedi riposo. Collegare il cavettoabbinato all’ART 1231/6D ai morsetti TX / RX / -. Il modulo 3340 e 3342 non deveessere in programmazione.
La rubrica deve esserevuota.
Oppure:
DOWNLOAD FALLITO
DOWNLOAD TERMINATO
Se il download staavvenendo correttamente.
Se ci sono problemi di connessione.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
DIGITA IL CODICE UTENTE
Inserire il codice utente.ESEMPIO: 1
Premere il tasto ENTERdell’Art.1230 per memorizzarenome e codice utente.
E’ possibile procedere conl’inserimento di altri utenti.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
CONDIZIONE INIZIALE
7D) INSERIMENTO TRAMITE SOFTWARE ART.1249
Avviare il softwareArt.1249.Consultare la Guida in linea del prodotto per i settagli richiesti.Premere il tasto F7 per avviare il download.
ATTENZIONE: La modalitàdi chiamata selezionatadeve corrispondere con quella impostata nel modulo Art. 3340.(vedi Punto 8)
Alla fine del download.
Modulo alimentato in con-dizione di riposo. Collegareil cavetto abbinatoall’Art.1249 ai morsettiTX / RX / -.Il modulo 3340 e 3342non deve essere in programmazione.
Oppure:
DOWNLOAD FALLITO
DOWNLOAD TERMINATO
Se il download staavvenendo correttamente.
Se ci sono problemi di connessione.
La rubrica deve esserevuota.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
DIGITA IL CODICE UTENTE
CODICE: _ _ 1
MEMORIZZAZIONE IN CORSO….
GROUP S.P.A.
FT SB 08 8
CONDIZIONE INIZIALE
7E) INSERIMENTO DIRETTAMENTE DA TASTIERA (non disponibile se la modalità di chiamata è Codice Indiretto; vedi punto 8)
Selezionare il menu GESTIONERUBRICA / INSERIMENTONOMI / MANUALE.
Procedere con l’inserimentodel nome utente.ESEMPIO: ROSSI GIOVANNI
Premere il tasto perprocedere con l’inserimentodel codice utente. ESEMPIO: 1
Premere il tasto per memorizzare nome e codice utente.
E’ possibile procedere conl’inserimento di altri utenti.
Modulo alimentato con morsetto PR collegatoal morsetto - .
Il modulo è in fase di programmazione:
per selezionare il menu▲▼per scorrere i menu
per passare al menu precedente.
_
ROSSI GIOVANNI _
CODICE: _ _ 1
MEMORIZZAZIONE IN CORSO…
Oppure:NOME GIA’ PRESENTE
IN RUBRICA
_
Il modulo è pronto perl’inserimento dei nomi.
Per cancellare il carattere asinistra del cursore premereil tasto X , per caratterispeciali il tasto 9 . , :
Se il nome utente è giàpresente in rubrica.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
GESTIONE RUBRICACONTROLLO ACCESSI
IMPOSTAZIONI
CONDIZIONE INIZIALE
7F) MODIFICA DI UN NOME O DI UN CODICE UTENTE(non disponibile se la modalità di chiamata è Codice Indiretto; vedi Punto 8)
Selezionare il menu GESTIONE RUBRICA /MODIFICA NOMI.
Inserire il nome utente chesi vuole modificare,anchecon parte dell’estensione.ESEMPIO: ROSS
Premere il tasto perprocedere con la ricercadel nome utente.
Utilizzare i tasti ▲▼perscorrere la lista degli utenti.Selezionare il nome utenteche si desidera modificare. ESEMPIO: ROSSI GIOVANNI
Premere il tasto perprocedere con la modificadel nome utente.
Modulo alimentato conmorsetto PR collegato almorsetto - .
Il modulo è in fase di programmazione:
per selezionare il menu▲▼per scorrere i menu
per passare al menu precedente.
INSERIRE IL NOMEANCHE CON PARTE DELL’ESTENSIONE
ROSS _
RICERCA IN
CORSO…
ROSSI GIOVANNI
ROSSI GIOVANNI _
Viene richiesto l’inserimentodel nome utente che si vuolemodificare.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
GESTIONE RUBRICACONTROLLO ACCESSI
IMPOSTAZIONI
FT SB 08
9 FT SB 08
ITA
LIA
NO
CONDIZIONE INIZIALE
7G) CANCELLAZIONE DI UN NOME (non disponibile se la modalità di chiamata è Codice Indiretto)
Modulo alimentato conmorsetto PR collegato almorsetto - .
Il modulo è in fase di programmazione:
per selezionare il menu▲▼per scorrere i menu
per passare al menu precedente.
GESTIONE RUBRICACONTROLLO ACCESSI
IMPOSTAZIONI
Modificare il nome tramitela tastiera alfanumerica.
Premere il tasto perprocedere con la modificadel codice utente.
Modificare il codice tramitela tastiera alfanumerica.
Premere il tasto permemorizzare nome ecodice utente.
E’ possibile procedere con la modifica di un altro utente.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
ROSSI GIOVANN_
CODICE: _ _ 1
CODICE _ _ 2
MEMORIZZAZIONE IN CORSO…
Oppure:NOME GIA’ PRESENTE
IN RUBRICA
Selezionare il menu GESTIONE RUBRICA / CANCELLAZIONE NOMI.
Inserire il nome utente chesi vuole cancellare,anchecon parte dell’estensione.ESEMPIO: ROSS
Premere il tasto perprocedere con la ricercadel nome utente.
Utilizzare i tasti ▲▼perscorrere la lista degli utenti. Selezionare il nome utenteche si desidera cancellare. ESEMPIO: ROSSI GIOVANNI
Premere il tasto perprocedere con la cancel-lazione del nome utente.
E’ possibile procedere con la cancellazione di un altro utente.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
INSERIRE IL NOMEANCHE CON PARTE DELL’ESTENSIONE
ROSS _
RICERCA IN
CORSO…
ROSSI GIOVANNI
ELIMINAZIONE IN CORSO…
Viene richiesto l’inserimentodel nome utente che sivuole cancellare.
GROUP S.P.A.
FT SB 08 10
CONDIZIONE INIZIALE
7H) CANCELLAZIONE DI UN NOME TRAMITE Art. 1230 (non disponibile se la modalità di chiamata è Codice Indiretto; vedi Punto 8)
Selezionare il nome utente che si desidera eliminare scorrendo la lista con i tasti ▲▼ .
Premere il tasto NAME <-dell’Art.1230.
Premere il tasto ENTERdell’Art.1230 per confermare l’eliminazione.
Modulo alimentato in condizione di riposo.
Se sono stati memorizzatidegli utenti in rubrica.
GIOVANNI ROSSI
ELIMINARE IL NOME ?
ELIMINAZIONEIN CORSO…
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
DIGITA IL CODICE UTENTE
Seguito da:SCORRI NOMI CERCA NOME
CONDIZIONE INIZIALE
7I) CANCELLAZIONE DI TUTTI I NOMI PRESENTI IN RUBRICA
Modulo alimentato con morsetto PR collegatoal morsetto - .
Il modulo è in fase di programmazione:
per selezionare il menu▲▼per scorrere i menu
per passare al menu precedente.
GESTIONE RUBRICACONTROLLO ACCESSI
IMPOSTAZIONI
Selezionare il menu GESTIONE RUBRICA /AZZERA TUTTI I NOMI
Premere il tasto per elim-inare tutti gli utenti in rubrica.Premere il tasto perannullare l’operazione.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
ELIMINARE TUTTI I NOMI ?
ELIMINAZIONE IN CORSO…
CONDIZIONE INIZIALE
7L) VISUALIZZAZIONE DEL NUMERO DI NOMI INSERITI IN RUBRICA, DELLA VERSIONE SOFTWARE INSTALLATA E DEL CODICE ID
Selezionare il menu INFO.
Modulo alimentato con morsetto PR collegato al morsetto - .
Il modulo è in fase di programmazione:
per selezionare il menu▲▼per scorrere i menu
per passare al menu precedente.
Comelit
REV. 1.6NOMI IN RUBRICA: 0INDIRIZZO RS485 255
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
GESTIONE RUBRICACONTROLLO ACCESSI
IMPOSTAZIONI
FT SB 08
11 FT SB 08
ITA
LIA
NO
8) IMPOSTAZIONE DELLA MODALITA’ DI FUNZIONAMENTO(Standard oppure Codice Indiretto)
8A) MODALITA’ DI CHIAMATA STANDARD ( Default )In questa modalità di funzionamento l’utente citofonico è identificato da un campo NomeUtente e da un campo Codice. ESEMPIO: Nome utente = Rossi ; Codice = 1La chiamata può avvenire nei seguenti modi:1) Seleziono l’utente Rossi tramite i tasti ▲▼➔ premo il tasto ➔ invio la chiamata
all’utente identificato con il codice 1. 2) Digito da tastiera il codice 1 ➔ premo il tasto .
8B) MODALITA’ DI CHIAMATA CODICE INDIRETTO In questa modalità di funzionamento l’utente citofonico è identificato dai campi Codice indiretto , Nome Utente (opzionale) e Codice.ESEMPIO: Nome utente = Rossi ; Codice = 1 ; Codice Indiretto = 100La chiamata può avvenire nei seguenti modi:1) Seleziono l’utente Rossi tramite i tasti ▲▼➔ premo il tasto ➔ invio la chiamata
all’utente identificato con il codice 1. 2) Digito da tastiera il Codice Indiretto 100 ➔ premo il tasto ➔ invio la chiamata
all’utente identificato con il codice 1.
L’inserimento della lista con i campi elencati può avvenire solamente tramite il softwareArt.1249.Il codice indiretto può essere al massimo di 6 cifre. Il campo Nome Utente può anche essere omesso (vedi Modalità Codice Indiretto senzacampo nome nella Guida in linea Art.1249 ). Per aggiornare un modulo in cui è già stata memorizzata una lista bisogna prima eseguireuna cancellazione totale di quella presente seguendo la procedura di paragrafo“CANCELLAZIONE DI TUTTI I NOMI PRESENTI IN RUBRICA”.
CONDIZIONE INIZIALE
Per selezionare la modalità di chiamata Standard oppure Codice Indiretto è necessarioeseguire le seguenti operazioni:
Selezionare il menuIMPOSTAZIONI / GEST. CHIAMATA.
Selezionare la modalitàdesiderata mediante i tasti ▲▼.
Premere il tasto per confermare la scelta.
Modulo alimentato conmorsetto PR collegato almorsetto - .
Il modulo è in fase di programmazione:
per selezionare il menu▲▼per scorrere i menu
per passare al menu precedente.
GEST. CHIAMATA* STANDARD
CODICE INDIRETTO
GEST. CHIAMATA* STANDARD
CODICE INDIRETTO
GEST. CHIAMATASTANDARD
* CODICE INDIRETTO
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
GESTIONE RUBRICACONTROLLO ACCESSI
IMPOSTAZIONI
GROUP S.P.A.
FT SB 08 12
9) MODIFICA DEI PARAMETRI D’IMPIANTO
9A) IMPOSTAZIONE DEI PARAMETRI DEL PORTER ART. 1602-4660 (tempo di apriporta, tempo di fonica e tempo di attesa reset. Per tempo di attesa reset si intende il tempo che intercorre tra la chiusura di unacomunicazione e la possibilità di poterne intraprendere un’altra).
CONDIZIONE INIZIALE
Premere per selezionareil menu IMPOSTAZIONI / PARAMETRI IMPIANTO /PARAMETRI PORTER.
Selezionare il parametroche si vuole modificare.ESEMPIO: tempo di fonica.
Modificare il valore del para-metro agendo sui tasti ▲▼,per annullare l’operazionepremere il tasto .
Modulo Art.3340 alimentatocon morsetto PR collegato al morsetto - .
Modulo Art.1602 / 4660 alimentato con morsettoPR collegato al morsetto - .
Il modulo è in fase di programmazione:
per selezionare il menu▲▼per scorrere i menu
per passare al menu precedente.
Il modulo è in fase di programmazione.
INS. TEMPO FONICAINS. TEMPO APRIPINS. TEMPO RESET
INS. TEMPO FONICAINS. TEMPO APRIPINS. TEMPO RESET
VALORE IN SEC. 010 Valori ammissibiliTempo fonica: da 10 a 180 sec. Tempo apriporta: da 1 a 99 sec.Tempo attesa reset: da 0 a 10 sec.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
GESTIONE RUBRICACONTROLLO ACCESSI
IMPOSTAZIONI
Confermare il valore premendo il tasto
PARAMETRO MODIFICATO
Si udirà un tono di confermasul modulo porter Art. 1602/4660.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
9B) VISUALIZZAZIONE DEI PARAMETRI DEL PORTER ART. 1602 – 4660 (tempo di apriporta, di fonica e di attesa reset)
CONDIZIONE INIZIALE
Selezionare il menuIMPOSTAZIONI / PARAMETRI IMPIANTO /PARAMETRI PORTER /VISUALIZZA.
Modulo Art. 3340 alimentato con morsettoPR collegato al morsetto -.
Modulo Art.1602 / 4660 alimentato con morsettoPR collegato al morsetto - .
Il modulo è in fase di programmazione:
per selezionare il menu▲▼per scorrere i menu
per passare al menu precedente.
TEMPO APRIPORTA 01TEMPO FONICA 010TEMPO ATT. RESET 10
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
GESTIONE RUBRICACONTROLLO ACCESSI
IMPOSTAZIONI
Vengono visualizzati iparametri impostati sulmodulo porter Art.1602/4660.
ATTENZIONE: La funzione viene garantitasolo con moduli porter chemontano una versionesoftware 2.0 o superiore.
FT SB 08
13 FT SB 08
ITA
LIA
NO
10) GESTIONE DELLA FUNZIONE DI CONTROLLO ACCESSI
10A) SUPERCODICE DI DEFAULT
Il supercodice permette l’accesso alle operazioni di INSERIMENTO, CANCELLAZIONE eRICERCA di un codice password che permette di attivare il relè presente sul moduloporter , tipicamente utilizzato come apriporta.
10B) MODIFICA DEL SUPERCODICE ( Default = 778899 )9C) IMPOSTAZIONE DEL CODICE ID ( Default = 255 ) Il codice ID viene utilizzato solo in applicazioni speciali.
CONDIZIONE INIZIALE
Selezionare il menuIMPOSTAZIONI / PARAMETRI IMPIANTO /INDIRIZZO RS485.
Premere il tasto perconfermare la scelta .
Agire sui tasti ▲▼
per modificare il valore del codice ID.
Premere il tasto per memorizzare il valore.
Modulo Art. 3340 alimentatocon morsetto PR collegatoal morsetto - .
Il modulo è in fase di programmazione:
per selezionare il menu▲▼per scorrere i menu
per passare al menu precedente.
INDIRIZZO RS485: 01
INDIRIZZO RS485: 01
INDIRIZZO RS485: 254
PARAMETROMODIFICATO
Il codice ID visualizzato non è quello configurato.
Il codice ID visualizzato nonè quello configurato.
Il codice può avere un valorecompreso tra 1 e 255.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
GESTIONE RUBRICACONTROLLO ACCESSI
IMPOSTAZIONI
CONDIZIONE INIZIALE
Selezionare il menu CONTROLLO ACCESSI /SUPERCODICE /INSERISCI NUOVO.
Inserire il supercodice attualmente impostato. Deveessere composto da 6 cifre.
Premere il tasto perconfermare l’inserimento.
Inserire il nuovo supercodice. Deve esserecomposto da 6 cifre.
Premere il tasto perconfermare l’inserimento.
Modulo alimentato conmorsetto PR collegato almorsetto - .
Il modulo è in fase di programmazione:
per selezionare il menu▲▼per scorrere i menu
per passare al menu precedente.
Se il supercodice inseritocorrisponde a quelloattualmente memorizzato.
Se il supercodice inseritonon corrisponde a quelloattualmente memorizzato.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
GESTIONE RUBRICACONTROLLO ACCESSI
IMPOSTAZIONI
SUPERCODICE ATTUALE:_ _ _ _ _ _
SUPERCODICE ATTUALE:* * * * * *
NUOVO SUPERCODICE:_ _ _ _ _ _
Oppure:
SUPERCODICE ERRATO
NUOVO SUPERCODICE:* * * * * *
SUPERCODICEMODIFICATO
GROUP S.P.A.
FT SB 08 14
10C) AZZERAMENTO DEL SUPERCODICE
CONDIZIONE INIZIALE
Selezionare il menu CONTROLLO ACCESSI /SUPERCODICE / AZZERA.
Modulo alimentato con morsetto PR collegatoal morsetto - .
Il modulo è in fase di programmazione:
per selezionare il menu▲▼per scorrere i menu
per passare al menu precedente.
SUPERCODICE MODIFICATO
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
GESTIONE RUBRICACONTROLLO ACCESSI
IMPOSTAZIONI
Il supercodice viene riportato al valore di default(778899).
10E) CANCELLAZIONE DI UN CODICE PASSWORD
CONDIZIONE INIZIALE
Selezionare il menu CONTROLLOACCESSI / PASSWORD.
Modulo alimentato con morsetto PR collegatoal morsetto - .
Il modulo è in fase di programmazione:
per selezionare il menu▲▼per scorrere i menu
per passare al menu precedente.
SUPERCODICE ATTUALE:_ _ _ _ _ _
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
GESTIONE RUBRICACONTROLLO ACCESSI
IMPOSTAZIONI
10D) INSERIMENTO DI UN CODICE PASSWORD (Default = nessun codice memorizzato)
CONDIZIONE INIZIALE
Selezionare il menu CONTROLLO ACCESSI /PASSWORD.
Inserire il supercodice.
Modulo alimentato con morsetto PR collegatoal morsetto - .
Il modulo è in fase di programmazione:
per selezionare il menu▲▼per scorrere i menu
per passare al menu precedente.
SUPERCODICE ATTUALE:_ _ _ _ _ _
SUPERCODICE ATTUALE:* * * * * *
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
GESTIONE RUBRICACONTROLLO ACCESSI
IMPOSTAZIONI
Premere il tasto perconfermare l’inserimento.
Selezionare il menuINSERISCI.
Inserire il valore di password desiderato.
Premere il tasto perconfermare l’inserimento.
E’ possibile procedere con l’inserimento di altrepassword.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
INSERISCICANCELLA
TROVA
INSERISCI PASSWORD:_ _ _ _ _ _
INSERISCI PASSWORD:* * * * * *
MEMORIZZAZIONE IN CORSO…
INSERISCI PASSWORD:_ _ _ _ _ _
Si accede al menu di gestione delle password di apriporta.
La password può esserecomposta da 1 a 6 caratteri.
FT SB 08
15 FT SB 08
ITA
LIA
NO
10F) CANCELLAZIONE DI TUTTI I CODICI DI PASSWORD
CONDIZIONE INIZIALE
Selezionare il menu CONTROLLO ACCESSI /PASSWORD.
Inserire il supercodice.
Premere il tasto per confermare l’inserimento.
Selezionare il menuAZZERA.
Premere il tasto per confermare l’eliminazionedi tutte le password.
Modulo alimentato con morsetto PR collegatoal morsetto - .
Il modulo è in fase di programmazione:
per selezionare il menu▲▼per scorrere i menu
per passare al menu precedente.
SUPERCODICE ATTUALE:_ _ _ _ _ _
SUPERCODICE ATTUALE:* * * * * *
INSERISCICANCELLA
TROVA
ELIMINARETUTTE LE PASSWORD?
ELIMINAZIONEIN CORSO…
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
GESTIONE RUBRICACONTROLLO ACCESSI
IMPOSTAZIONI
Viene richiesto l’inserimentodel supercodice.
Si accede la menu di gestione delle password di apriporta.
Inserire il supercodice.
Premere il tasto per confermare l’inserimento.
Selezionare il menu CANCELLA.
Premere il tasto per confermare la scelta .
Inserire il valore di passwordche si desidera eliminare.
Premere il tasto per confermare l’inserimento.
E’ possibile procedere con l’eliminazione di altre password.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
SUPERCODICE ATTUALE:* * * * * *
INSERISCICANCELLA
TROVA
INSERISCICANCELLA
TROVA
CANCELLA PASSWORD:_ _ _ _ _ _
CANCELLA PASSWORD:* * * * * *
ELIMINAZIONE IN CORSO…
Oppure:CANCELLA PASSWORD:
X X X X X X
CANCELLA PASSWORD:_ _ _ _ _ _
Si accede la menu di gestione delle passworddi apriporta.
Se la password è statatrovata all’interno della lista.
Se la password non vienetrovata, viene mostrata quella con valore simile. E’ possibile scorrere la listadelle password inseriteagendo sui tasti ▲▼, percancellare quella selezionatapremere il tasto .
GROUP S.P.A.
FT SB 08 16
10G) RICERCA DI UN CODICE DI PASSWORD
CONDIZIONE INIZIALE
Selezionare il menu CONTROLLO ACCESSI /PASSWORD.
Inserire il supercodice.
Premere il tasto per confermare l’inserimento.
Selezionare il menuTROVA.
Inserire il valore di passwordche si desidera ricercare. ESEMPIO:112233
Premere il tasto per confermare l’inserimento.
Modulo alimentato con morsetto PR collegatoal morsetto - .
Il modulo è in fase di programmazione:
per selezionare il menu▲▼per scorrere i menu
per passare al menu precedente.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
GESTIONE RUBRICACONTROLLO ACCESSI
IMPOSTAZIONI
Si accede al menu di gestione delle password di apriporta.
Viene mostrata la passwordricercata oppure quella convalore simile memorizzataall’interno della lista.
E’ possibile visualizzare la lista delle passwordinserite agendo sui tasti ▲▼.
TROVA PASSWORD:112244
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
Le password sonomemorizzate in ordinecrescente.
CONDIZIONE INIZIALE
10H) ATTIVAZIONE DEL RELE’ DI APRIPORTA DIGITANDO IL CODICE DI PASSWORD
Premere il tasto .
Digitare il codice di password.
Premere il tasto .
Modulo alimentato in condizione di riposo.
Se sono stati memorizzatidegli utenti in rubrica.
INSERISCI PASSWORD:_ _ _ _ _ _
INSERISCI PASSWORD:* * * * * *
PASSWORD CONFERMATA
Oppure
PASSWORD ERRATA
Viene richiesto il codice di password.
Se è un codice presente in memoria,viene attivato il relè presente nel moduloart.1602 / 4660.
Se è un codice non presente in memoria.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
DIGITA IL CODICE UTENTE
Seguito da:
SCORRI NOMI CERCA NOME
SUPERCODICE ATTUALE:_ _ _ _ _ _
SUPERCODICE ATTUALE:* * * * * *
INSERISCICANCELLA
TROVA
TROVA PASSWORD:_ _ _ _ _ _
TROVA PASSWORD:* * * * * *
TROVA PASSWORD:112233
FT SB 08
17 FT SB 08
ITA
LIA
NO
10I) VISUALIZZAZIONE DEL NUMERO DI PASSWORD INSERITE
CONDIZIONE INIZIALE
Modulo alimentato con morsetto PR collegatoal morsetto - .
Il modulo è in fase di programmazione:
per selezionare il menu▲▼per scorrere i menu
per passare al menu precedente.
GESTIONE RUBRICACONTROLLO ACCESSI
IMPOSTAZIONI
Selezionare il menu CONTROLLO ACCESSI /INFO.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
Comelit PASSWORDINSERITE: 1
Viene visualizzato il numero di passwordinserite.
11) IMPOSTAZIONE DEL TIPO DI CONNESSIONE CON PC, RS232 oppure RS485 (Default = RS232)
CONDIZIONE INIZIALE
Modulo alimentato con morsetto PR collegatoal morsetto - .
Il modulo è in fase di programmazione:
per selezionare il menu▲▼per scorrere i menu
per passare al menu precedente.
GESTIONE RUBRICACONTROLLO ACCESSI
IMPOSTAZIONI
Selezionare il menuIMPOSTAZIONI / TIPO DOWNLOAD
Selezionare la modalità di download agendo sui tasti ▲▼. ESEMPIO: RS485
Premere il tasto per confermare la scelta.
TIPO DOWNLOAD *RS232RS485
TIPO DOWNLOAD *RS232RS485
TIPO DOWNLOAD RS232* RS485
L’impostazione di DEFAULTè RS232.
La modalità impostata vienecontraddistinta da unasterisco sul fianco sinistro.
Apparirà un asterisco sul fianco sinistro della voce scelta.ATTENZIONE: Per il download in modalitàRS485 rifarsi allo schema di collegamento CA/EN/108a pagina 74.
VISUALIZZAZIONE DISPLAY DESCRIZIONEOPERAZIONE
GROUP S.P.A.
FT SB 08 18
• INTRODUCTION page 19
• 1) KEY FUNCTIONS page 19
• 2) INSTALLATION OF THE MODULE page 20
• 3) SETTING THE LANGUAGE page 20
3A) First time the module is turned on, the language has not been selected yet page 20
3B) Changing the language set previously page 20
• 4) SELF–DIAGNOSIS page 20
• 5) USING THE NAME DIRECTORY page 21
5A) Scrolling and calling the user selected page 21
5B) Searching for a name in the directory page 21
• 6) USING THE CALL MODULE page 22
• 7) MANAGING THE DIRECTORY page 22
7A) Entering a name page 22
7B) Entering by means of art. 1230 page 22
7C) Entering by means of software art. 1231/6D page 23
7D) Entering by means of software art. 1249 page 23
7E) Entering directly from the keypad page 24
7F) Changing a name page 24
7G) Cancelling a name page 25
7H) Cancelling a name by means of Art.1230 page 26
7I) Cancelling all the names in the directory page 26
7L) Displaying the number of names entered in the directory, page 26
the software version installed and the ID Code
• 8) SETTING THE OPERATING MODE
(STANDARD OR INDIRECT CODE) page 27
8A) Standard call mode page 27
8B) Indirect code call mode page 27
• 9) MODIFYING THE SYSTEM PARAMETERS page 28
9A) Setting the porter art.1602-4660 parameters
(door opening time, conversation time and reset wait time) page 28
9B) Displaying the porter art.1602 – 4660 parameters
(door opening, conversation and reset wait time) page 28
9C) Setting the ID code page 29
• 10) MANAGEMENT OF THE ACCESS CONTROL FUNCTION page 29
10A) Default supercode page 29
10B) Changing the supercode page 29
10C) Resetting the supercode page 30
10D) Entering a password code page 30
10E) Cancelling a password code page 30
10F) Cancelling all the password codes page 31
10G) Searching for a password code page 32
10H) Activating the door opening relay by entering the password code page 32
10I) Displaying the number of passwords entered page 33
• 11) SETTING THE TYPE OF CONNECTION,
RS232 OR RS485, WITH THE PC page 33
SUMMARY
FT SB 08
19 FT SB 08
EN
GL
ISH
The Comelit digital call module Art.3340 can be used in Simplebus type systems, is
fitted with a name directory to store a list of user names and with an alphanumerical
keypad to call the door entry phone users by entering the code which identifies them.
The main characteristics are as follows:
• Memory capacity: 400 names of 18 alphanumerical characters.
• Graphic display with 128x64 dots/pitch resolution.
• 2 call management modes : Standard or indirect code .
• Entering the name list ( Download ) by means of programmer Art.1230 or by means
of connection with a PC fitted with software Art.1231/6D or Art.1249.
• Entering the names by means of connection with the PC can be done over an
RS232 line or over an RS485 line by means of the interface card Art.1319 ( see
system diagram CA_EN_108 ).
• Reading ( Upload ) of the name list stored in the directory module by means of
connection with a PC fitted with software Art.1249.
• Access control with the possibility of storing up to 300 password codes to activate
the relay in the porter module, typically used as a door opener.
• Possibility of displaying the graphic interface messages in one of the 9 languages
available.
1) KEY FUNCTIONSINTRODUCTION
CALL – SELECT MENU
BACK: Scrolls the user list in decreasing alphabetical order
FORWARD: Scrolls the user list in increasing alphabetical order.
SEARCH FOR NAME - EXIT MENU
CALL - LOCAL DOOR OPENING
CANCEL CHARACTERor CALL
GROUP S.P.A.
FT SB 08 20
INITIAL CONDITION
3) SETTING THE LANGUAGE
3A) THE FIRST TIME THE MODULE IS TURNED ON, THE LANGUAGE HAS NOT YET BEEN SELECTED:
3B) CHANGING THE LANGUAGE SET PREVIOUSLY:
Scroll the list by means of the ▲▼ keys.To select the language required, press
On power up
* ITALIANOENGLISH
FRANCAIS
The DEFAULT item setsthe ITALIAN language. The next time the module is turned on, selection of the language is requestedagain.
ON DISPLAY DESCRIPTIONOPERATION
INITIAL CONDITION
Powered up with PRterminal connectedto terminal - .
The module is in programming mode:
to select the menu▲▼to scroll the menus.
to return to the previous menu.
SELECT LANGUAGE:*ITALIANENGLISH
TEST DESCRIPTION
4) SELF – DIAGNOSIS
On power up, the apparatus carries out a diagnostic test of the connections to check correctcommunication with porter module ART.1602/4660 and with the keypad module which makesup ART. 3340. If the wordi OK appears next to the item, then it has passed the test, otherwise,if the word FAILED appears it has failed the test. On completion of the Self-Diagnosis mode,press the ▼key to put the module in the into its normal mode of operation. The table summari-sing the meaning of the single tests is given below:
2) INSTALLATION OF THE MODULE
Follow what is indicated in technical sheet FT/SB/07 or MT/SB2/02 to cable module Art.3340. To prevent any interference caused by electrostatic discharges, it is advisable toscreen the casing as shown in the diagram on page 74.
INITIALIZING
SPEAK. SERIAL
MODE
Check the EEPROM which contains the user name list. If the test fails, the module is faulty.
If the test fails, check correct serial connection with porter module. Art.1602 / 4660 .
Check presence of the alphanumerical keypad whichmakes up Art.3340. If the wording 3342 appears next to thedescription, correct connection between the alphanumericalkeypad and the directory module must be checked.
ON DISPLAY DESCRIPTIONOPERATION
SELECT LANGUAGE:*ITALIANENGLISH
SELECT LANGUAGE:ITALIAN
*ENGLISH
The default language onpower up is Italian.The language set is marked by an asterisk on the left-hand side.When repowered thelanuage resets to Italian by default.
Select the SETTINGS /SELECT LANG. menu
Scroll the list by means of the ▲▼keys.To select the language required, press
NAME DIRECTORYACCESS CONTROL
SETTINGS
FT SB 08
21 FT SB 08
EN
GL
ISH
INITIAL CONDITION
5) USING THE NAME DIRECTORY
5A) SCROLLING AND CALLING THE USER SELECTED
Scroll the list by means of the ▲▼keys.To exit, press the key
Press the keyto call the selected user.
It is possible to cancelthe call or the conversation in progressby pressing the X key.
During normal operation.
If some users have beenstored in the directory.
GIOVANNI ROSSI The names are entered in alphabetical order.
The call has been madecorrectly.
The call has not been made correctly.
The system is engaged.
ON DISPLAY DESCRIPTIONOPERATION
ENTER TENANTCODE
Followed by:
SCROLL NAMESSEARCH NAME
CONDIZIONE INIZIALE
5B) SEARCHING FOR A NAME IN THE DIRECTORY
Press the key.
Enter the user name withpart of the extension as well.EXAMPLE: SMITH
Press the key to start the search.
Now it is possible to scrollthe user name list usingthe ▲▼keys.
During normal operation.
ENTER THEREQUIRED
NAME TO SEARCH
SMI_
SEARCHIN PROGRESS…
SMITH JOHN
Or:
NAME NOT STOREDIN DIRECTORY
The user name found is displayed
The user name does not exist
ON DISPLAY DESCRIPTIONOPERATION
SCROLL NAMESSEARCH NAME
Followed by:
ENTER TENANTCODE
CALL EFFECTED
Or:
USER NOT AVAILABLE
Or:
USER BUSY
CALL EFFECTED
Or:
COMMUNICATING
GROUP S.P.A.
FT SB 08 22
INITIAL CONDITION
6) USING THE CALL MODULE
EXAMPLE: If you want tocall the user with code 1.Press key 1 on thealphanumerical keypad.
Press the or key to call
It is now possible to cancel the call or the conversation in progressby pressing the X key.
During normal operation.
CALL USER:_ _ 1
CALL EFFECTEDOr:
USER NOT AVAILABLE
Or:USER BUSY
CALL EFFECTED Or:
COMMUNICATING
The call has been madecorrectly.The call has not been made correctly.
The system is engaged.
ON DISPLAY DESCRIPTIONOPERATION
SCROLL NAMESSEARCH NAME
Followed by:ENTER TENANT
CODE
INITIAL CONDITION
7B) ENTERING BY MEANS OF ART. 1230(not available if the call mode is In direct Code - see Point 8)
Press the NAME->of Art.1230.
Enter the user name to be inserted.EXAMPLE:SMITH JOHN
Press the ENTER keyof Art. 1230.
During normal operation.
If some users have beenstored in the directory.
ENTERING A NAME
SMITH JOHN
CODE: _ _ _
To use the lower-casecharacters of the keys, pressSHIFT. To cancel thecharacter on the left press < .To enter special characters,press the combination of keys described below:NAME -> + A = ÅNAME -> + B = ÄNAME -> + C = ßNAME -> + O = ÖNAME -> + P = ØNAME -> + Q = ÜPress ESC to cancel the user name entry operation.
ON DISPLAY DESCRIPTIONOPERATION
ENTER TENANTCODE
Followed by:
SCROLL NAMESSEARCH NAME
7) MANAGING THE DIRECTORY
7A) ENTERING A NAMEIt is possible to store a name in the directory by means of infrared programmer ART.1230,or by means of software ART.1231/6D - ART.1249, or directly by means of the alphanu-merical keypad the module is fitted with.
FT SB 08
23 FT SB 08
EN
GL
ISH
INITIAL CONDITION
7C) ENTERING BY MEANS OF SOFTWARE ART. 1231/6D
Run the software Art.1231/6D.The settings required by thesoftware are:- Load the database containing
user names and codes.- Select the COMPATIBLE
mode from the DOWN-LOAD menu.
- Select the COM port.Press the DOWNLOAD pushbutton.
On completion of downloading.
During normal operation..Connect the cable combinedwith ART. 1231/6D to theTX / RX / - terminals. Module3340 and 3342 must not be under programming.
The directory must beempty.
Or:
DOWNLOADFAILED
DOWNLOAD TERMINATED
If downloading is takingplace correctly.
If there are connectionproblems.
ON DISPLAY DESCRIPTIONOPERATION
ENTER TENANTCODE
Enter the user name.EXAMPLE: 1
Press the ENTER keyof Art. 1230 to store the user name and code.
It is possible to proceed to enter other users.
ON DISPLAY DESCRIPTIONOPERATION
INITIAL CONDITION
7D) ENTERING BY MEANS OF SOFTWARE ART.1249
Run the software Art.1249.Consult the online Guide of the products for the settings required.Press the F7 key to start downloading.
CAUTION: The call mode selectedmust correspond with the one set in moduleArt. 3340. (see Point 8)
On completion of downloading.
During normal operation..Connect the cable combined with ART. 1249to the TX / RX / - terminals. Module 3340 and 3342must not be under programming.
Or:
DOWNLOADFAILED
DOWNLOAD TERMINATED
If downloading is takingplace correctly.
If there are connectionproblems.
The directory must beempty.
ON DISPLAY DESCRIPTIONOPERATION
ENTER TENANTCODE
CODICE: _ _ 1
STORING IN PROGRESS….
GROUP S.P.A.
FT SB 08 24
INITIAL CONDITION
7E) ENTERING DIRECTLY FROM THE KEYPAD(not available if the call mode is Indirect Code - see Point 8)
Select the NAMEDIRECTORY/ENTERINGNAMES/MANUALLY menu.
Proceed with user name entry.EXAMPLE:JOHN SMITH
Press the key to proceed with the user code entry.EXAMPLE: 1
Press the key to storethe user name and code.
It is possible to proceed toenter other users.
Powered upwith PR terminal connect-ed to terminal - .
The module is in the programming mode:
to select the menu▲▼to scroll the menus
to return to the previous menu
_
JOHN SMITH_
CODE: _ _ 1
STORING IN PROGRESS…
Or:NAME ALREADY
IN MEMORY
_
The module is ready forentering the names.
To cancel the character tothe left of the cursor, pressthe X key, for specialcharacters, key 9..:
If the user name is already in the directory.
ON DISPLAY DESCRIPTIONOPERATION
NAME DIRECTORY ACCESS CONTROL
SETTINGS
INITIAL CONDITION
7F) CHANGING A NAME OR A USER CODE(not available if the call mode is Indirect Code - see Point 8)
Select the NAMEDIRECTORY/ CHANGENAMES menu.
Enter the user name to bemodified, with part of theextension as well.EXAMPLE: SMIT
Press the key to proceed with searching for the user name.
Use the ▲▼ keys to scroll the user name list. Select the user name to be modified. EXAMPLE: JOHN SMITH
Press the key to proceed with modificationof the user name.
Powered up with PR terminal connectedto terminal - .
The module is in the programming mode:
to select the menu▲▼to scroll the menus.
to return to the previous menu.
ENTER PARTOF THE NAME
REQUIRED
SMIT_
SEARCH IN PROGRESS…
JOHN SMITH
JOHN SMITH
The user name to bemodified is requested.
ON DISPLAY DESCRIPTIONOPERATION
NAME DIRECTORY ACCESS CONTROL
SETTINGS
FT SB 08
25 FT SB 08
EN
GL
ISH
INITIAL CONDITION
7G) CANCELLING A NAME(not available if the call mode is Indirect Code - see Point 8)
Powered up with PR terminal connectedto terminal - .
The module is in the programming mode:
to select the menu▲▼to scroll the menus.
to return to the previous menu.
NAME DIRECTORYACCESS CONTROL
SETTINGS
Modify the name by means of the alphanumerical keypad.
Press the key to proceed with modificationof the user code.
Modify the code by means of the alphanu-merical keypad.
Press the key to storethe user name and code.
It is possible to proceed tomodify another user.
ON DISPLAY DESCRIPTIONOPERATION
JOHN SMITH _
CODE: _ _ 1
CODE _ _ 2
STORING IN PROGRESS…
Or:NAME ALREADY
IN MEMORY
Select the NAMEDIRECTORY/DELETINGNAMES menu.
Enter the user name to becancelled, with part of theextension as well.EXAMPLE: SMI
Press the key to proceed with searching for the user name.
Use the ▲▼keys to scroll the user list. Select the user name to be cancelled.EXAMPLE: SMITH JOHN
Press the key to proceed with cancelling the user name.
It is possible to proceed tocancel another user.
ON DISPLAY DESCRIPTIONOPERATION
ENTER PARTOF THE NAME
REQUIRED
SMI _
SEARCH IN PROGRESS …
SMITH JOHN
ELIMINATION IN PROGRESS…
The user name to be cancelled is requested.
GROUP S.P.A.
FT SB 08 26
INITIAL CONDITION
7H) CANCELLING A NAME BY MEANS OF Art. 1230 (not available if the call mode is Indirect Code - see Point 8)
Select the user name to be eliminated byscrolling the list by means of the ▲▼keys.
Press the NAME-> keyof Art.1230.
Press the ENTER keyof Art. 1230 to confirmelimination.
In normal mode of operation.
If some users have beenstored in the directory.
SMITH JOHN
ELIMINATETHE NAME?
DELETINGMEMORY...
ON DISPLAY DESCRIPTIONOPERATION
ENTER TENANTCODE
Followed by:SCROLL NAMESSEARCH NAME
INITIAL CONDITION
7I) CANCELLING ALL THE NAMES IN THE DIRECTORY
Powered up with PR terminal connected to terminal - .
The module is in the programming mode:
to select the menu▲▼to scroll the menus.
to return to the previous menu.
NAME DIRECTORYACCESS CONTROL
SETTINGS
Select the NAMEDIRECTORY/DELETEALL NAMES menu.
Press the key to eliminate all the users inthe directory. Press the
key to cancel theoperation.
ON DISPLAY DESCRIPTIONOPERATION
DELETEALL NAMES?
ELIMINATIONIN PROGRESS…
INITIAL CONDITION
7L) DISPLAYING THE NUMBER OF NAMES ENTERED IN THE DIRECTORY, THE SOFTWARE VERSION INSTALLED AND THE ID CODE
Select the INFO menu.
Powered up with PR terminal connectedto terminal - .
The module is in the programming mode:
to select the menu▲▼to scroll the menus.
to return to the previous menu.
Comelit
REV. 1.6NAMES STORED: 0ADDRESSE RS485: 255
ON DISPLAY DESCRIPTIONOPERATION
NAME DIRECTORYACCESS CONTROL
SETTINGS
FT SB 08
27 FT SB 08
EN
GL
ISH
8) SETTING THE OPERATING MODE(Standard or indirect code)
8A) STANDARD CALL MODE ( Default )In this operating mode the entry phone user is identified by a un User Name field and bya Code field.EXAMPLE: User name = Smith ; Code = 1The call can be made in the following ways:1) I select the user Smith by means of the ▲▼keys ➔ I press the key ➔ I send the
call to the user identified with code 1.2) From the keypad I enter the code 1 ➔ I press the key.
8B) INDIRECT CODE CALL MODEIn this operating mode the entry phone user is identified by the Indirect code, User name(optional) and Code fields.EXAMPLE: User name = Smith ; Code = 1 ; Indirect Code = 100The call can be made in the following ways:1) I select the user Smith by means of the ▲▼keys ➔ I press the key ➔ I send the
call to the user identified with code 1.2) From the keypad I enter the Indirect Code 100 ➔ I press the key ➔ I send the call
to the user identified with code 1.
Entry of the list with the listed fields can only be carried out by means of the softwareArt.1249.The indirect code can have a maximum of 6 figures.The User Name field can also be omitted (see Indirect Code Mode without name fieldin the online Guide Art.1249 ).To update a module where a list has already been stored, it is first necessary tocompletely cancel the one present, following the procedure in the “CANCELLING ALLTHE NAMES IN THE DIRECTORY” paragraph.
INITIAL CONDITION
To select the Standard call mode or indirect code, the following operations must becarried out:
Select the SETTINGS /CALL OPERATINGmenu
Select the desired mode by means of the ▲▼ keys.
Press the key to confirm the selection
Powered up with PR terminal connectedto terminal - .
The module is in the programming mode:
to select the menu▲▼to scroll the menus.
to return to the previous menu.
CALL OPERATING* STANDARD
INDIRECT CODE
CALL OPERATING* STANDARD
INDIRECT CODE
CALL OPERATINGSTANDARD
* INDIRECT CODE
ON DISPLAY DESCRIPTIONOPERATION
NAME DIRECTORYACCESS CONTROL
SETTINGS
GROUP S.P.A.
FT SB 08 28
9) MODIFYING THE SYSTEM PARAMETERS
9A) SETTING THE PORTER ART. 1602-4660 PARAMETERS (door opening time, conversation time and reset wait time).The time which passes between closing down a communication and the possibility ofbeing able to start another is meant by reset wait time).
INITIAL CONDITION
Press to select the SETTINGS / SYSTEMPARAMETERS / SPEAKERPARAMETERS menu
Select the parameter to be modified. EXAMPLE:conversation time.
Modify the parameter value by means of the ▲▼ keys,press the key to cancel the operation.
Module Art.3340 poweredup with PR terminal connected to terminal - .
Module Art.1602 / 4660powered up with PR termi-nal connected to terminal -.
The module is in the programming mode:
to select the menu▲▼to scroll the menus.
to return to the previous menu.
The module is in theprogramming mode
ENTER AUDIO TIMINGENT. DOOR LOCK TIMEENTER RESET TIME
ENTER AUDIO TIMINGENT. DOOR LOCK TIMEENTER RESET TIME
VALUE IN SECS. 010 Admissible values. Conversationtime from 10 to 180 sec. Dooropening time: from 1 to 99 sec.Reset wait time: from 0 to 10 sec.
ON DISPLAY DESCRIPTIONOPERATION
NAME DIRECTORYACCESS CONTROL
SETTINGS
Press the key to confirm the value
PARAMETERCHANGED
A confirmation tone willbe heard on porter moduleArt. 1602/4660.
ON DISPLAY DESCRIPTIONOPERATION
9B) DISPLAYING THE PORTER ART.1602 – 4660 PARAMETERS(door opening time, conversation time and reset wait time).
INITIAL CONDITION
Select the SETTINGS /SYSTEM PARAMETERS /SPEAKER PARAMETERS/VIEWING menu
Module Art.3340 poweredup with PR terminal connected to terminal - .
Module Art.1602 / 4660powered up with PR termi-nal connected to terminal - .
The module is in the programming mode:
to select the menu▲▼to scroll the menus.
to return to the previous menu.
DOOR LOCK TIME 01AUDIO TIMING 010WAITING TIME 10
ON DISPLAY DESCRIPTIONOPERATION
NAME DIRECTORYACCESS CONTROL
SETTINGS
The parameters set on theporter Art. 1602/4660module are displayed.
CAUTION:The function is only guaran-teed with porter moduleswhich have a software version of 2.0 or later.
FT SB 08
29 FT SB 08
EN
GL
ISH
10) MANAGEMENT OF THE ACCESS CONTROL FUNCTION
10A) DEFAULT SUPERCODE
The supercode allows access to ENTER, CANCELLATION and SEARCH for a passwordcode which allows the relay present in the porter module to be activated, which is typicallyused as door opener.
10B) CHANGING THE SUPERCODE ( Default = 778899 )9C) SETTING THE ID CODE ( Default = 255 ) The ID code is only used in special applications.
INITIAL CONDITION
Select the SETTINGS /SYSTEM PARAMETERS /RS485 ADDRESS menu
Press the key to confirm the selection.
Use the ▲▼keysto modify the value of the ID code
Press the key to storethe value.
Module Art.3340 poweredup with PR terminal connected to terminal - .
The module is in the programming mode:
to select the menu▲▼to scroll the menus.
to return to the previous menu.
RS485 ADDRESS: 01
RS485 ADDRESS: 01
RS485 ADDRESS: 254
PARAMETERCHANGED
The ID code displayed isnot the one configured.
The ID code displayed is not the one configured.
The code can have a valuefrom 1 to 255.
ON DISPLAY DESCRIPTIONOPERATION
NAME DIRECTORYACCESS CONTROL
SETTINGS
INITIAL CONDITION
Select the ACCESS CONTROL / SUPERCODE /ENTER NEW ONE menu.
Enter the supercodecurrently set. It must have 6 figures.
Press the key to confirm the entry.
Enter the new supercode. It must have 6 figures.
Press the key to confirm the entry.
Module Art.3340 poweredup with PR terminal connected to terminal - .
The module is in the programming mode:
to select the menu▲▼to scroll the menus.
to return to the previous menu.
If the supercode enteredcorresponds to the onecurrently stored.
If the supercode entereddoes not correspond to theone currently stored.
ON DISPLAY DESCRIPTIONOPERATION
NAME DIRECTORYACCESS CONTROL
SETTINGS
SUPERCODE IN USE:_ _ _ _ _ _
SUPERCODE IN USE:* * * * * *
NEW SUPERCODE:_ _ _ _ _ _
Or:
SUPERCODE WRONG
NEW SUPERCODE:* * * * * *
SUPERCODECHANGED
GROUP S.P.A.
FT SB 08 30
10C) RESETTING THE SUPERCODE
INITIAL CONDITION
Select the ACCESS CONTROL / SUPERCODE /DELETE menu
Module powered up with PR terminal connected to terminal - .
The module is in the programming mode:
to select the menu▲▼to scroll the menus.
to return to the previous menu.
SUPERCODECHANGED
ON DISPLAY DESCRIPTIONOPERATION
NAME DIRECTORYACCESS CONTROL
SETTINGS
The supercode is takenback to the default value(778899).
10E) CANCELLING A PASSWORD CODE
INITIAL CONDITION
Select the ACCESS CONTROL / PASSWORDmenu
Module powered up with PR terminal connected to terminal - .
The module is in the programming mode:
to select the menu▲▼to scroll the menus.
to return to the previous menu.
SUPERCODE IN USE:_ _ _ _ _ _
ON DISPLAY DESCRIPTIONOPERATION
NAME DIRECTORYACCESS CONTROL
SETTINGS
10D) ENTERING A PASSWORD CODE (Default = no code stored)
INITIAL CONDITION
Select the ACCESS CONTROL /PASSWORD menu
Enter the supercode
Module powered upwith PR terminalconnected to terminal - .
The module is in the programming mode:
to select the menu▲▼to scroll the menus.
to return to the previous menu.
SUPERCODE IN USE:_ _ _ _ _ _
SUPERCODE IN USE:* * * * * *
ON DISPLAY DESCRIPTIONOPERATION
NAME DIRECTORYACCESS CONTROL
SETTINGS
Press the key to confirm the entry.
Select the ENTRY menu.
Enter the desired password value.
Press the key to confirm the entry.
It is possible to proceed to enter other passwords.
ON DISPLAY DESCRIPTIONOPERATION
ENTERDELETESEARCH
ENTER PASSWORD:_ _ _ _ _ _
ENTER PASSWORD:* * * * * *
STORINGIN PROGRESS…
ENTER PASSWORD:_ _ _ _ _ _
You access the door-opening passwordmanagement menu.
The password can have from 1 to 6 characters.
FT SB 08
31 FT SB 08
EN
GL
ISH
10F) CANCELLING ALL THE PASSWORD CODES
INITIAL CONDITION
Selectthe ACCESS CONTROL /PASSWORD menu
Enter the supercode
Press the key to confirm the entry.
Select the DELETE menu.
Press the key to confirm elimination of all the passwords.
Module powered up with PR terminal connected to terminal - .
The module is in the programming mode:
to select the menu▲▼to scroll the menus.
to return to the previous menu.
SUPERCODE IN USE:_ _ _ _ _ _
SUPERCODE IN USE:* * * * * *
ENTERDELETESEARCH
DELETE ALLPASSWORDS?
DELETINGMEMORY...
ON DISPLAY DESCRIPTIONOPERATION
NAME DIRECTORYACCESS CONTROL
SETTINGS
Entry of the supercode is requested.
You access the door-opening passwordmanagement menu.
Enter the supercode
Press the key to confirm the entry.
Select the DELETE menu.
Press the key to confirm the selection.
Enter the password value to be eliminated.
Press the key to confirm the entry.
It is possible to proceed to eliminateother passwords.
ON DISPLAY DESCRIPTIONOPERATION
SUPERCODE IN USE:* * * * * *
ENTERDELETESEARCH
ENTERDELETESEARCH
DELETE PASSWORD:_ _ _ _ _ _
DELETE PASSWORD:* * * * * *
DELETINGMEMORY...
Or:DELETE PASSWORD:
X X X X X X
DELETE PASSWORD:_ _ _ _ _ _
You access the door-opening passwordmanagement menu.
If the password was foundin the list.
If the password is not found,the one with a similarvaluesis shown.It is possible to scroll the listof entered passwords by using the ▲▼keys. To cancel the one selected,press the key .
GROUP S.P.A.
FT SB 08 32
10G) SEARCHING FOR A PASSWORD CODE
INITIAL CONDITION
Selectthe ACCESS CONTROL /PASSWORD menu
Enter the supercode
Press the key to confirm the entry.
Select the SEARCH menu.
Enter the password value tobe searched for.EXAMPLE:112233
Press the key to confirm the entry.
Module powered up with PR terminal connectedto terminal - .
The module is in the programming mode:
to select the menu▲▼to scroll the menus.
to return to the previous menu.
ON DISPLAY DESCRIPTIONOPERATION
NAME DIRECTORYACCESS CONTROL
SETTINGS
You access thedoor-opening passwordmanagement menu.
The password searched for or the one with a similarvalue stored in the list is shown.
It is possible to displaythe list of passwordsentered using the ▲▼keys.
SEARCH PASSWORD:112244
ON DISPLAY DESCRIPTIONOPERATION
The passwords are stored in increasing order
INITIAL CONDITION
10H) ACTIVATING THE DOOR OPENING RELAY BY ENTERING THE PASSWORD CODE
Press the key.
Enter the password code
Press the key.
In normal mode of operation.
If some users have beenstored in the directory.
ENTER PASSWORD:_ _ _ _ _ _
ENTER PASSWORD:* * * * * *
PASSWORDCONFIRMED
Or
WRONG PASSWORD
Entry of the password codeis requested.
If it is a code in the memory,the relay in module art.1602/ 4660 is activated.
If a code is not in the memory.
ON DISPLAY DESCRIPTIONOPERATION
ENTER TENANTCODE
Followed by:
SCROLL NAMESSEARCH NAME
SUPERCODE IN USE:_ _ _ _ _ _
SUPERCODE IN USE:* * * * * *
ENTERDELETESEARCH
SEARCH PASSWORD:_ _ _ _ _ _
SEARCH PASSWORD:* * * * * *
SEARCH PASSWORD:112233
FT SB 08
33 FT SB 08
EN
GL
ISH
10I) DISPLAYING THE NUMBER OF PASSWORDS ENTERED
INITIAL CONDITION
Module powered up with PR terminal connected to terminal - .
The module is in the programming mode:
to select the menu▲▼to scroll the menus.
to return to the previous menu.
NAME DIRECTORYACCESS CONTROL
SETTINGS
Select the ACCESS CONTROL / INFO menu
ON DISPLAY DESCRIPTIONOPERATION
Comelit PASSWORDSENTERED: 1
The number of passwordsentered is displayed.
11) SETTING THE TYPE OF CONNECTION WITH THE PC, RS232 or RS485 (Default = RS232)
INITIAL CONDITION
Module powered up with PR terminal connectedto terminal - .
The module is in the programming mode:
to select the menu▲▼to scroll the menus.
to return to the previous menu.
NAME DIRECTORYACCESS CONTROL
SETTINGS
Select the SETTINGS /TYPE OF DOWNLOADmenu
Select the download modeusing the ▲▼keys.EXAMPLE: RS485
Press the key to confirm the selection.
TYPE OF DOWNLOAD *RS232RS485
TYPE OF DOWNLOAD*RS232RS485
TYPE OF DOWNLOADRS232* RS485
The DEFAULT setting is RS232.
The mode set is marked byan asterisk on the left side.
An asterisk will appear onthe left side of the itemselected.ATTENTION:For downloading in RS485 mode, refer to the CA/EN/108 connection diagramon page 74.
ON DISPLAY DESCRIPTIONOPERATION
GROUP S.P.A.
FT SB 08 34
• INTRODUCTION page 35
• 1) FONCTION DES TOUCHES page 35
• 2) INSTALLATION DU MODULE page 36
• 3) PROGRAMMATION DE LA LANGUE page 36
3A) Lors du premier branchement du module,
la langue n’a pas encore été sélectionnée page 36
3B) Modification de la langue précédemment programmée page 36
• 4) AUTODIAGNOSTIC page 36
• 5) UTILISATION DU RÉPERTOIRE PORTE-NOMS page 37
5A) Défilement et appel de l’usager sélectionné page 37
5B) Recherche d’un nom dans le répertoire page 37
• 6) UTILISATION DU MODULE D’APPEL page 38
• 7) GESTION DU RÉPERTOIRE page 38
7A) Entrée d’un nom page 38
7B) Entrée au moyen de l’art. 1230 page 38
7C) Entrée au moyen du logiciel art. 1231/6D page 39
7D) Entrée au moyen du logiciel art. 1249 page 39
7E) Entrée directement en intervenant sur le clavier page 40
7F) Modification d’un nom ou d’un code d’utilisateur page 40
7G) Effacement d’un nom page 41
7H) Effacement d’un nom au moyen de l’art.1230 page 42
7I) Effacement de tous les noms présents dans le répertoire page 42
7L) Affichage du nombre de noms entrés dans le répertoire,
de la version du logiciel installé et du Code ID page 42
• 8) PROGRAMMATION DU MODE DE FONCTIONNEMENT
(STANDARD OU CODE INDIRECT) page 43
8A) Mode d’appel standard page 43
8B) Mode d’appel code indirect page 43
• 9) MODIFICATION DES PARAMÈTRES DE L’INSTALLATION page 44
9A) Programmation des paramètres du HP-micro art.1602-4660
(temps d’ouvre-porte, temps de phonie et temps d’attente restauration) page 44
9B) Affichage des paramètres du HP-micro art.1602 – 4660
(temps d’ouvre-porte, temps de phonie et temps d’attente restauration) page 44
9C)Programmation du Code ID page 45
• 10) GESTION DE LA FONCTION DE CONTRÔLE DES ACCÈS page 45
10A) Supercode de défaut page 45
10B) Modification du supercode page 45
10C) Mise à zéro du supercode page 46
10D) Entrée d’un code d’utilisateur page 46
10E) Effacement d’un code d’utilisateur page 46
10F) Effacement de tous les codes d’utilisateur page 47
10G) Recherche d’un code d’utilisateur page 48
10H) Activation du relais d’ouvre-porte en numérisant le code d’utilisateur page 48
10I) Affichage du nombre de codes d’utilisateur mémorisés page 49
• 11) PROGRAMMATION DU TYPE DE CONNEXION AU PC,
RS232 OU RS485 page 49
SOMMAIRE
FT SB 08
35 FT SB 08
FR
AN
ÇA
IS
Le module d’appel numérique Comelit Art. 3340 s’utilise dans des installations de type
Simplebus. Il est équipé d’un répertoire porte-noms pour mémoriser une liste de noms
d’usagers et d’un clavier alphanumérique pour appeler les usagers, en composant le
code qui les identifie. Ses principales caractéristiques sont :
• Capacité de la mémoire: 400 noms de 18 caractères alphanumériques.
• Afficheur graphique avec définition 128x64 dots/pitch.
• 2 modes de gestion de l’appel : Standard ou Code Indirect.
• Téléchargement de la liste de noms ( Download ) à travers le programmateur
Art.1230 ou à travers la connexion au PC équipé du logiciel Art.1231/6D ou
Art.1249.
• L’entrée des noms à travers la connexion au PC peut avoir lieu sur la ligne RS232
ou sur la ligne RS485 à travers la carte d’interface Art.1319 (voir schéma
d’installation CA_EN_108).
• Lecture (Upload) de la liste de noms mémorisée dans le module répertoire à travers
la connexion au PC équipée du logiciel Art.1249.
• Contrôle des Accès avec la possibilité de mémoriser jusqu’à 300 codes d’utilisateur
pour activer le relais présent dans le module HP-micro, typiquement utilisé comme
ouvre-porte.
• Possibilité d’afficher les messages de l’interface graphique dans une des 9 langues
disponibles.
1) FONCTION DES TOUCHESINTRODUCTION
APPEL – SÉLECTION MENU
EN ARRIÈRE: fait défiler la liste des noms par ordre alphabétique décroissant.
EN AVANT: fait défiler la liste des noms par ordre alphabétique croissant.
RECHERCHE NOM -QUITTER LE MENU
APPEL – OUVRE-PORTE LOCAL
EFFACEMENT CARACTÈRE OU APPEL
GROUP S.P.A.
FT SB 08 36
CONDITION INITIALE
3) PROGRAMMATION DE LA LANGUE
3A) LORS DU PREMIER BRANCHEMENT DU MODULE, LA LANGUE N’A PAS ENCOREÉTÉ SÉLECTIONNÉE :
3B) MODIFICATION DE LA LANGUE PRÉCÉDEMMENT PROGRAMMÉE:
Faire défiler la liste en appuyant sur les touches ▲▼. Pour sélectionner la languedésirée appuyer sur .
Module alimenté.
* ITALIANOENGLISH
FRANCAIS
La rubrique par DÉFAUTprogramme les messages enitalien, lors du branchementsuccessif du module, leprogramme demande à nouveaude sélectionner la langue.
AFFICHAGE DESCRIPTIONOPERATION
CONDITION INITIALE
Module alimenté par la borne PR reliée à la borne -.
Le module est en programmation.
pour sélectionner le menu▲▼pour faire défiler le menu
pour passer au menuprécédent.
CHOISIR LANGUE*ITALIANOENGLISH
TEST DESCRIPTION
4) AUTODIAGNOSTIC
Lors du branchement, l’appareil effectue un diagnostic des connexions pour vérifier que lacommunication est correcte avec le module HP-micro ART.1602/4660 et avec le module cla-vier qui compose l’ART. 3340. Si, à côté de la rubrique, s’affiche l’inscription OK , le test estpositif, dans le cas contraire l’inscription ÉCHOUÉ s’affiche. A la fin de l’autodiagnostic,appuyer sur la touche ▼ pour amener le module en état de repos. Nous indiquons ci-des-sous le tableau qui récapitule la signification de chaque test.
2) INSTALLATION DU MODULE
Se conformer aux indications contenues dans la feuille technique FT/SB/07 ou MT/SB2/02pour le câblage du module Art. 3340. Pour éviter tout dérangement provoqué par desdécharges électrostatiques, il est conseillé d’effectuer un blindage de la carcasse, de lamanière indiquée dans le schéma page 74.
INITIALISATION
SERIEL HP
MODE
Vérification de l’écriture correcte de l’EEPROM qui contient la liste desnoms usagers. Si le test échoue, c’est l’indice que le module est en panne.
Si le test échoue, vérifier que la connexion série avec le module HP-micro Art.1602 / 4660 est correcte.
Vérification de la présence du clavier alphanumérique qui compose l’Art.3340. Si l’inscription 3342 s’affiche à côté de ladescription, vérifier que la connexion entre le clavieralphanumérique et le module répertoire est correcte.
AFFICHAGE DESCRIPTIONOPERATION
CHOISIR LANGUE*ITALIANOENGLISH
CHOISIR LANGUE*ITALIANOENGLISH
La langue programmée estmarquée d’un astérisque à gauche. La rubrique parDÉFAUT programme lesmessages en italien, lors du branchement successifdu module, le programmedemande à nouveau desélectionner la langue.
Sélectionner le menu PROGRAMMATIONS /SÉLECTIONNER LA LANGUE.
Faire défiler la liste en appuyant sur les touches ▲▼.Pour sélectionner la languedésirée appuyer sur .
RÉPERTOIRECONTRÔLE D'ACCÈS
REGLAGES
FT SB 08
37 FT SB 08
FR
AN
ÇA
IS
CONDITION INITIALE
5) UTILISATION DU RÉPERTOIRE PORTE-NOMS
5A) DÉFILEMENT ET APPEL DE L’USAGER SÉLECTIONNÉ
Faire défiler la liste enappuyant sur les touches▲▼. Pour quitter, appuyersur la touche
Appuyer sur la touche pour appeler l’usager sélectionné.
Pour annuler l’appel ou laconversation en cours,appuyer sur la touche X.
Module alimenté en condition de repos.
Si des usagers ont étémémorisés dans le répertoire
GIOVANNI ROSSI Les noms sont entrés par ordre alphabétique.
L’appel a eu lieucorrectement.
L’appel n’a pas eu lieucorrectement
Le poste est occupé.
AFFICHAGE DESCRIPTIONOPERATION
ENTRÈR LE CODEUSAGER
Suivi de :
DÉFIL. NOMSRECH. NOM
CONDITION INITIALE
5B) RECHERCHE D’UN NOM DANS LE RÉPERTOIRE
Appuyer sur la touche .
Entrer le nom de l’usager également avec une partie del’extension. EXEMPLE : ROSSI
Appuyer sur la touchepour commencer la recherche.
A présent, possibilité defaire défiler la liste des nomsdes usagers en appuyantsur les touches ▲▼.
Module alimenté en condition de repos.
INTRODUIRPARTIE DU NOM
A CHERCHER
ROS_
RECHERCHE EN COURS…
ROSSI GIOVANNI
Ou:
NOM PAS PRÉSENT
EN RÉPERTOIRE
Affichage du nom del’usager trouvé.
Le nom de l’usager n’existe pas.
AFFICHAGE DESCRIPTIONOPERATION
DÉFIL. NOMSRECH. NOM
Suivi de :
ENTRÈR LE CODEUSAGER
APPEL ENVOYÉ
Ou:
USAGER NONDISPONIBLE
Ou:
USAGER OCCUPÉ
APPEL ENVOYÉ
Ou
EN COMMUNICATION
GROUP S.P.A.
FT SB 08 38
CONDITION INITIALE
6) UTILISATION DU MODULE D’APPEL
EXEMPLE : pour appelerl’usager avec le code 1.Appuyer sur la touche 1 du clavier alphanumérique.
Appuyer sur la touche ou pour appeler.
Possibilité d’annuler l’appel ou la conversationen cours en appuyant sur la touche X.
Module alimenté en condition de repos.
APPEL USAGER:_ _ 1
APPEL ENVOYÉOu:
USAGER NONDISPONIBLE
Ou:USAGER OCCUPÉ
APPEL ENVOYÉ Ou:
EN COMMUNICATION
L’appel a eu lieucorrectement.L’appel n’a pas eu lieucorrectement.
Le poste est occupé.
AFFICHAGE DESCRIPTIONOPERATION
DÉFIL. NOMSRECH. NOM
Suivi de :ENTRÈR LE CODE
USAGER
CONDITION INITIALE
7B) ENTRÉE AU MOYEN DE L’ART. 1230(non disponible si le mode d’appel est le mode Code Indirect ; voir le Point 8).
Appuyer sur la toucheNAME -> de l’Art. 1230.
Numériser le nom de l’usager que l’on désire entrer.EXEMPLE : ROSSI GIOVANNI
Appuyer sur la toucheENTER de l’Art. 1230.
Module alimenté en condition de repos.
Si des usagers ont été mémorisés dans le répertoire.
ENTRÉE D’UN NOM
ROSSI GIOVANNI
CODE: _ _ _
Pour utiliser les caractèresinférieurs des touches,appuyer sur SHIFT. Poureffacer le caractère à gauche,appuyer sur <. Pour entrer descaractères particuliers, appuyersur les combinaisons detouches illustrée ci-dessous :NAME -> + A = ÅNAME -> + B = ÄNAME -> + C = ßNAME -> + O = ÖNAME -> + P = ØNAME -> + Q = ÜAppuyer sur ESC pourannuler l’opération d’entréedu nom de l’usager.
AFFICHAGE DESCRIPTIONOPERATION
ENTRÈR LE CODEUSAGERSuivi de :
DÉFIL. NOMSRECH. NOM
7) GESTION DU RÉPERTOIRE
7A) ENTRÉE D’UN NOMPossibilité de mémoriser un nom dans le répertoire par le biais du programmateur àl’infrarouge ART.1230, ou du logiciel ART.1231/6D - ART.1249, ou directement en inter-venant sur le clavier alphanumérique dont est équipé le module.
FT SB 08
39 FT SB 08
FR
AN
ÇA
IS
CONDITION INITIALE
7C) ENTRÉE AU MOYEN DU LOGICIEL ART.1231/6D
Mettre en route le logiciel Art. 1231/6D. Les réglagesdemandés par le logiciel sont :- Télécharger la base de don-
nées contenant les noms etles codes d’utilisateur.
- Sélectionner le mode COMPATIBLEdu menu TÉLÉCHARGEMENT.
- Sélectionner le port COM.Appuyer sur la toucheTÉLÉCHARGEMENT
A la fin du téléchargement.
Module alimenté en conditionde repos. Brancher le câbleassocié à l’Art. 1231/6D auxbornes TX / RX. Les modules3340 et 3342 ne doivent pasêtre en programmation.
Le répertoire doit êtrevide.
Ou:
TÉLÉCHARGEMENTÉCHOUÉ
TÉLÉCHARGEMENT TERMINÉ
Si le téléchargement a lieu correctement.
S’il y a des problèmes de connexion.
AFFICHAGE DESCRIPTIONOPERATION
ENTRÈR LE CODEUSAGER
Entrer le code d’utilisateur.EXEMPLE : 1
Appuyer sur la touche ENTRÉEde l’Art. 1230 pour mémoriser le nom et le code d’utilisateur.
Possibilité d’entrer lesnoms des autres usagers.
AFFICHAGE DESCRIPTIONOPERATION
CONDITION INITIALE
7D) ENTRÉE AU MOYEN DU LOGICIEL ART.1249
Mettre en route le logicielArt. 1249. Consulter leGuide en ligne du produitpour les réglages nécessaires. Appuyer sur la touche F7pour mettre en route le téléchargement.
ATTENTION : Le moded’appel sélectionné doit correspondre à celui programmé dans le moduleArt. 3340 (voir Point 8).
A la fin du téléchargement.
Module alimenté en condition de repos.Brancher le câble associé àl’Art. 1249 aux bornes TX /RX. Les modules 3340 et 3342 ne doivent pas être en programmation.
Ou:
TÉLÉCHARGEMENTÉCHOUÉ
TÉLÉCHARGEMENTTERMINÉ
Si le téléchargement a lieucorrectement.
S’il y a des problèmes de connexion..
Le répertoire doit être vide.
AFFICHAGE DESCRIPTIONOPERATION
ENTRÈR LE CODEUSAGER
CODE: _ _ 1
MÉMORISATION EN COURS….
GROUP S.P.A.
FT SB 08 40
CONDITION INITIALE
7E) ENTRÉE DIRECTEMENT EN INTERVENANT SUR LE CLAVIER(non disponible si le mode d’appel est le mode Code Indirect : voir point 8).
Sélectionner le menu RÉPERTOIREINTRODUIR NOMS / MANUEL.
Entrer le nom de l’usager.EXEMPLE : ROSSI GIOVANNI
Appuyer sur la touche pour entrer le Code d’utilisateur. EXEMPLE : 1
Appuyer sur la touche pour mémoriser le nom et le Code d’utilisateur.
Maintenant, vous pouvez entrerles noms des autres usagers.
Module alimenté par la borne PR reliée à la borne -.
Le module est en programmation.
pour sélectionner le menu▲▼pour faire défiler le menu
pour passer au menuprécédent.
_
ROSSI GIOVANNI _
CODE : _ _ 1
MÉMORISATION EN COURS….
Ou:NOM DÉJÀEXISTANT
_
Le module est prêt, les noms peuvent être entrés.
Pour effacer le caractère àgauche du curseur, appuyersur la touche X, pour lescaractères spéciaux,appuyer sur la touche 9.
Si le nom de l’usager est déjàprésent dans le répertoire.
AFFICHAGE DESCRIPTIONOPERATION
RÉPERTOIRECONTRÔLE D'ACCÈS
REGLAGES
CONDITION INITIALE
7F) MODIFICATION D’UN NOM OU D’UN CODE D’UTILISATEUR(non disponible si le mode d’appel est le mode Code Indirect : voir point 8).
Sélectionner le menu RÉPERTOIRE /CHANGER NOMS.
Entrer le nom de l’usagerque l’on désire modifier,également avec une partiede l’extension. EXEMPLE : ROSS
Appuyer sur la touche pour continuer la recherchedu nom usager.
Appuyer sur les touches▲▼pour faire défiler laliste des usagers.Sélectionner le nom del’usager que l’on désiremodifier. EXEMPLE :ROSSI GIOVANNI
Module alimenté par la borne PR reliée à la borne -.
Le module est en programmation.
pour sélectionner le menu▲▼pour faire défiler le menu
pour passer au menuprécédent.
INTRODUIRUNE PARTIE DU NOM
DESIRE
ROSS _
RECHERCHE EN
COURS….…
ROSSI GIOVANNI
Le programme demanded’entrer le nom de l’usagerque l’on désire modifier.
AFFICHAGE DESCRIPTIONOPERATION
RÉPERTOIRECONTRÔLE D'ACCÈS
REGLAGES
FT SB 08
41 FT SB 08
FR
AN
ÇA
IS
CONDITION INITIALE
7G) EFFACEMENT D’UN NOM(non disponible si le mode d’appel est le mode Code Indirect : voir point 8).
Module alimenté par la borne PR reliée à la borne -.
Le module est en programmation.
pour sélectionner le menu▲▼pour faire défiler le menu
pour passer au menuprécédent.
RÉPERTOIRECONTRÔLE D'ACCÈS
REGLAGES
Appuyer sur la touchepour modifier le nom de l’usager.
Modifier le nom en intervenantsur le clavier numérique.
Appuyer sur la touchepour modifier le coded’utilisateur.
Modifier le code en intervenantsur le clavier alphanumérique.
Appuyer sur la touchepour mémoriser le nom et le code d’utilisateur.
Maintenant, vous pouvezmodifier le nom d’un autreusager.
AFFICHAGE DESCRIPTIONOPERATION
ROSSI GIOVANNI _
ROSSI GIOVANN _
CODE :_ _ 1
CODE :_ _ 2
MÉMORISATION EN COURS…Ou
NOM DÉJÀEXISTANT
Sélectionner le menu RÉPERTOIRE /EFFACER NOMS.
Entrer le nom de l’usagerque l’on désire effacer,également avec une partiede l’extension.EXEMPLE : ROSS
Appuyer sur la touche pour continuer la recherchedu nom de l’usager.
Appuyer sur lestouches▲▼pour faire défiler la liste des usagers.Sélectionner le nom del’usager que l’on désireeffacer. EXEMPLE : ROSSI GIOVANNI
Appuyer sur la touche pour effacer le nom de l’usager.
Maintenant, vous pouvez effacer le nomd’un autre usager.
AFFICHAGE DESCRIPTIONOPERATION
INTRODUIRUNE PARTIE DU NOM
DESIRE
ROSS _
RECHERCHE EN
COURS….
ROSSI GIOVANNI
EFFACEMENT EN COURS
Le programme demanded’entrer le nom de l’usagerque l’on désire effacer.
GROUP S.P.A.
FT SB 08 42
CONDITION INITIALE
7H) EFFACEMENT D’UN NOM AU MOYEN DE L’Art 1230.(non disponible si le mode d’appel est le mode Code Indirect : voir point 8).
Sélectionner le nom del’usager que l’on désireéliminer en faisant défiler laliste avec les touches ▲▼.
Appuyer sur la toucheNAME -> de l’Art. 1230.
Appuyer sur la toucheENTRÉE de l’Art. 1230pour valider l’élimination.
Module alimenté en condition de repos.
Si des usagers ont étémémorisés dans le répertoire.
GIOVANNI ROSSI
ÉLIMINER LE NOM ?
EFFACEMENT EN COURS…
AFFICHAGE DESCRIPTIONOPERATION
ENTRÈR LE CODEUSAGERSuivi de:
DÉFIL. NOMSRECH. NOM
CONDITION INITIALE
7I) EFFACEMENT DE TOUS LES NOMS PRÉSENTS DANS LE RÉPERTOIRE
Module alimenté par la borne PR reliée à la borne -.
Le module est en programmation.
pour sélectionner le menu▲▼pour faire défiler le menu
pour passer au menuprécédent.
RÉPERTOIRECONTRÔLE D'ACCÈS
REGLAGES
Sélectionner le menu RÉPERTOIRE /EFFACER LES NOMS.
Appuyer sur la touche pour éliminer tous lesusagers du répertoire.Appuyer sur la touche pour annuler l’opération.
AFFICHAGE DESCRIPTIONOPERATION
EFFACER TOUS LES NOMS ?
EFFACEMENT EN COURS…
CONDITION INITIALE
7L) AFFICHAGE DU NOMBRE DE NOMS ENTRÉS DANS LE RÉPERTOIRE, DE LA VERSION DU LOGICIEL INSTALLÉ ET DU CODE ID.
Sélectionner le menu INFO.
Module alimenté par la borne PR reliée à la borne -.
Le module est en programmation.
pour sélectionner le menu▲▼pour faire défiler le menu
pour passer au menuprécédent.
ComelitRÉV. 1.6NOMS IN REPERT. O1ADRESSE RS485 : 255
AFFICHAGE DESCRIPTIONOPERATION
RÉPERTOIRECONTRÔLE D'ACCÈS
REGLAGES
FT SB 08
43 FT SB 08
FR
AN
ÇA
IS
8) PROGRAMMATION DU MODE DE FONCTIONNEMENT(Standard ou Code Indirect)
8A) MODE D’APPEL STANDARD (Défaut)Dans ce mode de fonctionnement, l’usager est identifié par un champ Nom Usager et parun champ Code.EXEMPLE: Nom usager = Rossi ; Code = 1L’appel peut avoir lieu dans l’une des manières suivantes:1) Sélectionner l’usager Rossi à l’aide des touches ▲▼➔ appuyer sur la touche ➔
envoyer l’appel à l’usager identifié avec le code 1.2) En intervenant sur le clavier, numériser le code 1 ➔ appuyer sur la touche .
8B) MODE D’APPEL CODE INDIRECTDans ce mode de fonctionnement, l’usager est identifié par les champs Code indirect,Nom Usager (option) et Code.EXEMPLE: Nom usager = Rossi ; Code = 1 ; Code indirect = 100L’appel peut avoir lieu de l’une des manières suivantes:1) Sélectionner l’usager Rossi à l’aide des touches ▲▼➔ appuyer sur la touche ➔
envoyer l’appel à l’usager identifié par le code 1.2) En intervenant sur le clavier, numériser le Code Indirect 100 ➔ appuyer sur la touche
➔ envoyer l’appel à l’usager identifié par le code 1.
L’entrée de la liste avec les champs énumérés peut uniquement avoir lieu à travers lelogiciel Art.1249.Le code indirect peut avoir au maximum 6 chiffres.Le champ Nom Utilisateur peut aussi être omis (voir Mode Code Indirect sans champnom dans le Guide en ligne Art.1249 ).Pour mettre à jour un module dans lequel une liste a déjà été mémorisée, réaliser d’abordun effacement total de la liste présente, en suivant la marche indiquée au paragraphe“EFFACEMENT DE TOUS LES NOMS PRÉSENTS DANS LE RÉPERTOIRE”.
CONDITION INITIALE
Pour sélectionner le mode d’appel Standard ou Code Indirect, suivre la marche ci-dessous :
Sélectionner le menu REGLAGES /GESTION APPEL
Sélectionner le modedésiré en appuyant sur les touches ▲▼.
Appuyer sur la touche pour valider la sélection.
Module alimentépar la borne PR reliée à la borne -.
Le module est en programmation.
pour sélectionner le menu▲▼pour faire défiler le menu
pour passer au menuprécédent.
GESTION APPEL*STANDARD
CODE INDIRECT
GESTION APPEL* STANDARD
CODE INDIRECT
GESTION APPEL* STANDARD
CODE INDIRECT
AFFICHAGE DESCRIPTIONOPERATION
RÉPERTOIRECONTRÔLE D'ACCÈS
REGLAGES
GROUP S.P.A.
FT SB 08 44
9) MODIFICATION DES PARAMÈTRES DE L’INSTALLATION
9A) PROGRAMMATION DES PARAMÈTRES DU HP MICRO ART. 1602-4660(temps d’ouvre-porte, temps de phonie et temps d’attente restauration. Par temps d’attente restauration on désigne le temps qui s’écoule entre l’arrêt d’unecommunication et la possibilité d’en entreprendre une autre).
CONDITION INITIALE
Appuyer sur pour sélectionner le menu REGLAGES/PARAMÈTRES SYST./PARAMÈTRES HP
Sélectionner le paramètre que l’on désire modifier.EXEMPLE : temps de audio
Modifier le paramètre en intervenant sur lestouches ▲▼, pour annuler l’opération appuyer sur la touche .
Module art. 3340 alimenté par la borne PR reliée à la borne -.
Module Art. 1602 / 4660alimenté par la borne PRreliée à la borne -.
Le module est en programmation.
pour sélectionner le menu▲▼pour faire défiler le menu
pour passer au menuprécédent.
Le module est en programmation
ENT. TEMPS AUDIOENT. TEMPS OUVREP.
ENT. TEMPS RESET
ENT. TEMPS AUDIOENT. TEMPS OUVREP.
ENT. TEMPS RESET
VALEUR EN SEC. 010 Valeurs admises : Temps dephonie : de 10 à 180 sec.Temps d’ouvre-porte : de 1 à99 sec. Temps d’attenterestauration : de 0 à 10 sec.
AFFICHAGE DESCRIPTIONOPERATION
RÉPERTOIRECONTRÔLE D'ACCÈS
REGLAGES
Valider la valeur enappuyant sur la touche
PARAMÈTRE MODIFIÉ
Émission d’une tonalité devalidation du module HP-micro Art. 1602 / 4660.
AFFICHAGE DESCRIPTIONOPERATION
9B) AFFICHAGE DES PARAMÈTRES DU HP MICRO ART. 1602-4660(temps d’ouvre-porte, temps de phonie et temps d’attente restauration.
CONDITION INITIALE
Sélectionner le menu REGLAGES /PARAMÈTRES SYST./PARAMÈTRES HPVISUALISER
Module art. 3340 alimenté par la borne PR reliée à la borne -.
Module Art. 1602 / 4660alimenté par la borne PRreliée à la borne -.
Le module est en programmation.
pour sélectionner le menu▲▼pour faire défiler le menu
pour passer au menuprécédent.
TEMPS OUVRE-PORTE 01TEMPS AUDIO 10TEMPS ATT. RESET 10
AFFICHAGE DESCRIPTIONOPERATION
RÉPERTOIRECONTRÔLE D'ACCÈS
REGLAGES
Affichage des paramètresprogrammés sur le moduleHP-micro Art. 1602/4660.
ATTENTION : Cette fonctionest exclusivement garantieavec les modules HP micromontant une version delogiciel 2.0 ou supérieure.
FT SB 08
45 FT SB 08
FR
AN
ÇA
IS
10) GESTION DE LA FONCTION DE CONTRÔLE DES ACCÈS
10A) SUPERCODE DE DÉFAUT
Le supercode permet l’accès aux opérations d’ENTRÉE, d’EFFACEMENT et deRECHERCHE d’un code d’utilisateur permettant d’activer le relais présent sur le moduleHP-micro, typiquement utilisé comme ouvre-porte.
10B) MODIFICATION DU SUPERCODE ( Défaut = 778899 )9C) PROGRAMMATION DU CODE ID (Défaut = 255)Le code ID est exclusivement utilisé dans des applications spéciales.
CONDITION INITIALE
Sélectionner le menu REGLAGES/PARAMÈTRES SYST./ADRESSE RS485
Appuyer sur la touche pour valider le choix.
Appuyer sur les touches▲▼pour modifier le code ID.
Appuyer sur la touche pour mémoriser le code.
Module art. 3340 alimentépar la borne PR reliéeà la borne -.
Le module est en programmation.
pour sélectionner le menu▲▼pour faire défiler le menu
pour passer au menuprécédent.
ADRESSE RS485 : 01
ADRESSE RS485 : 01
ADRESSE RS485 : 254
PARAMÈTRE MODIFIÉ
Le code ID affiché n’estpas celui configuré.
Le code ID affiché n’est pas celui configuré.
Le code peut avoir une valeurcomprise entre 1 et 255.
AFFICHAGE DESCRIPTIONOPERATION
RÉPERTOIRECONTRÔLE D'ACCÈS
REGLAGES
CONDITION INITIALE
Sélectionner le menuCONTRÔLE D'ACCÈS /SUPERCODE /INTRODUIR NOUVEAU
Entrer le supercode actuelle-ment programmé. Il doit secomposer de 6 chiffres.
Appuyer sur la touchepour valider l’entrée.
Entrer le nouveau supercode. Il doit se composer de 6 chiffres.
Appuyer sur la touchepour valider l’entrée.
Module alimenté par laborne PR reliée à la borne -.
Le module est en programmation.
pour sélectionner le menu▲▼pour faire défiler le menu
pour passer au menuprécédent.
Le supercode entrécorrespond à celuiactuellement mémorisé.
Si le supercode entré necorrespond pas à celuiactuellement mémorisé.
AFFICHAGE DESCRIPTIONOPERATION
RÉPERTOIRECONTRÔLE D'ACCÈS
REGLAGES
SUPERCODE ACTUEL:_ _ _ _ _ _
SUPERCODE ACTUEL * * * * * *
NOUVEAU SUPERCODE :_ _ _ _ _ _
Ou:
SUPERCODE FAUSSE
NOUVEAU SUPERCODE :* * * * * *
SUPERCODE MODIFIÉ
GROUP S.P.A.
FT SB 08 46
10C) MISE À ZÉRO DU SUPERCODE
CONDITION INITIALE
Sélectionner le menuCONTRÔLE D'ACCÈS /SUPERCODE / EFFACER
Module alimenté par la borne PR reliée à la borne -.
Le module est en programmation.
pour sélectionner le menu▲▼pour faire défiler le menu
pour passer au menuprécédent.
SUPERCODE MODIFIE :
AFFICHAGE DESCRIPTIONOPERATION
RÉPERTOIRECONTRÔLE D'ACCÈS
REGLAGES
Le supercode est ramené à la valeur de défaut (778899).
10E) EFFACEMENT D’UN CODE D’UTILISATEUR
CONDITION INITIALE
Sélectionner le menuCONTRÔLE D'ACCÈS /PASSWORD
Module alimenté par la borne PR reliée à la borne -.
Le module est en programmation.
pour sélectionner le menu▲▼pour faire défiler le menu
pour passer au menuprécédent.
SUPERCODE ACTUEL :_ _ _ _ _ _
AFFICHAGE DESCRIPTIONOPERATION
RÉPERTOIRECONTRÔLE D'ACCÈS
REGLAGES
10D) ENTRÉE D’UN CODE D’UTILISATEUR (Défaut = aucun code mémorisé)
CONDITION INITIALE
Sélectionner le menuCONTRÔLE D'ACCÈS /PASSWORD
Entrer le supercode.
Module alimenté par la borne PR reliée à la borne -.
Le module est en programmation.
pour sélectionner le menu▲▼pour faire défiler le menu
pour passer au menuprécédent.
SUPERCODE ACTUEL :_ _ _ _ _ _
SUPERCODE ACTUEL :* * * * * *
AFFICHAGE DESCRIPTIONOPERATION
RÉPERTOIRECONTRÔLE D'ACCÈS
REGLAGES
Appuyer sur la touchepour valider l’entrée.
Sélectionner le menuINTRODUIR
Entrer le code d’utilisateur désiré.
Appuyer sur la touchepour valider l’entrée.
Possibilité d’entrer d’autres codes d’utilisateur.
AFFICHAGE DESCRIPTIONOPERATION
INTRODUIREFFACERTROUVER
INTRODUIRPASSWORD_ _ _ _ _ _
INTRODUIRPASSWORD
* * * * * *
MEMORISATION ENCOURS….
INTRODUIRPASSWORD:
_ _ _ _ _ _
Accès au menu de gestiondes codes d’utilisateurd’ouvre-porte.
Le code d’utilisateur peut secomposer de 1 à 6 caractères.
FT SB 08
47 FT SB 08
FR
AN
ÇA
IS
10F) EFFACEMENT DE TOUS LES CODES D’UTILISATEUR
CONDITION INITIALE
Sélectionner le menuCONTRÔLE D'ACCÈS /PASSWORD
Entrer le supercode.
Appuyer sur la touche pour valider l’entrée.
Sélectionner le menu EFFACER.
Appuyer sur la touche pour valider l’élimination de tous les codes d’utilisateur.
Module alimenté par la borne PR reliée à la borne -.
Le module est en programmation.
pour sélectionner le menu▲▼pour faire défiler le menu
pour passer au menuprécédent.
SUPERCODE ACTUEL :_ _ _ _ _ _
SUPERCODE ACTUEL :* * * * * *
INTRODUIREFFACERTROUVER
PASSWORDS?EFFACER LES
ÉLIMINATION EN COURS …
AFFICHAGE DESCRIPTIONOPERATION
RÉPERTOIRECONTRÔLE D'ACCÈS
REGLAGES
Le programme demanded’entrer le supercode.
Accès au menu de gestiondes codes d’utilisateurd’ouvre-porte.
Entrer le supercode.
Appuyer sur la touche pour valider l’entrée.
Sélectionner le menuEFFACER
Appuyer sur la touche pour valider la sélection.
Entrer le code d’utilisateurque l’on désire éliminer.
Appuyer sur la touche pour valider l’entrée.
Possibilité d’éliminerd’autres codes d’utilisateur.
AFFICHAGE DESCRIPTIONOPERATION
SUPERCODE ACTUEL :* * * * * *
INTRODUIREFFACERTROUVER
INTRODUIR EFFACERTROUVER
EFFACERPASSWORD_ _ _ _ _ _
EFFACERPASSWORD
* * * * * *
ÉLIMINATION EN COURS…
Ou :
EFFACERPASSWORD:
X XXXXX
EFFACER _ _ _ _ _ _
Accès au menu de gestiondes codes d’utilisateurd’ouvre-porte.
Si le code d’utilisateur a ététrouvé dans la liste.Si le code d’utilisateur n’a pas ététrouvé, le programme affichera lecode ayant une valeur semblable.Possibilité de faire défiler la liste des codes d’utilisateurmémorisés en appuyant sur les touches ▲▼. Pour effacer le code d’utilisateur sélectionné,appuyer sur la touche .
GROUP S.P.A.
FT SB 08 48
10G) RECHERCHE D’UN CODE D’UTILISATEUR
CONDITION INITIALE
Sélectionner le menuCONTRÔLE D'ACCÈS/PASSWORD
Entrer le supercode.
Appuyer sur la touchepour valider l’entrée.
Sélectionner le menuTROUVER
Entrer le code d’utilisateur à chercher.EXEMPLE : 112233
Appuyer sur la touchepour valider l’entrée..
Module alimenté par la borne PR reliée à la borne -.
Le module est en programmation.
pour sélectionner le menu▲▼pour faire défiler le menu
pour passer au menuprécédent.
AFFICHAGE DESCRIPTIONOPERATION
RÉPERTOIRE CONTRÔLE D'ACCÈS
REGLAGES
Accès au menu de gestiondes codes d’utilisateurd’ouvre-porte.
Affichage du code d’utilisateurcherché ou de celui ayant unevaleur similaire mémorisédans la liste.
Possibilité d’afficher la listedes codes d’utilisateurmémorisés en appuyant sur les touches ▲▼.
TROUVERPASSWORD
112244
AFFICHAGE DESCRIPTIONOPERATION
Les codes d’utilisateurs sont mémorisés par ordrecroissant.
CONDITION INITIALE
10H) ACTIVATION DU RELAIS D’OUVRE-PORTE EN NUMÉRISANT LE CODED’UTILISATEUR
Appuyer sur la touche .
Numériser le code d’utilisateur.
Appuyer sur a touche .
Module alimenté en condition de repos.
Si des noms ont étémémorisés dans le répertoire.
INTRODUIR PASSWORD_ _ _ _ _ _
INTRODUIRPASSWORD
* * * * * *
PASSWORDCONFIRMEE
Ou
PASSWORDFAUSSE
Le programme demande lecode d’utilisateur.
Si ce code est présent dans la mémoire, le relaisprésent dans le module art. 1602 / 4660 s’active.
Si ce code n’est pas présent dans la mémoire.
AFFICHAGE DESCRIPTIONOPERATION
ENTRÈR LE CODEUSAGER
Suivi de :
DÉFIL. NOMSRECH. NOM
SUPERCODE ACTUEL :_ _ _ _ _ _
SUPERCODE ACTUEL :* * * * * *
INTRODUIREFFACERTROUVER
TROUVERPASSWORD:
_ _ _ _ _ _
TROUVERPASSWORD
* * * * * *
TROUVERPASSWORD
112233
FT SB 08
49 FT SB 08
FR
AN
ÇA
IS
10 I) AFFICHAGE DU NOMBRE DE CODES D’UTILISATEUR MÉMORISÉS
CONDITION INITIALE
Module alimenté par la borne PR reliée à la borne -.
Le module est en programmation.
pour sélectionner le menu▲▼pour faire défiler le menu
pour passer au menuprécédent.
RÉPERTOIRE CONTRÔLE D'ACCÈS
REGLAGES
Sélectionner le menuCONTRÔLE D'ACCÈS / INFO.
AFFICHAGE DESCRIPTIONOPERATION
Comelit PASSWORD
INSEREES : 1
Affichage du nombre decodes d’utilisateurs entrés.
11) PROGRAMMATION DU TYPE DE CONNEXION AU PC, RS232 ou RS485 (Défaut = RS232)
CONDITION INITIALE
Module alimenté par la borne PR reliée à la borne -.
Le module est en programmation.
pour sélectionner le menu▲▼pour faire défiler le menu
pour passer au menuprécédent.
RÉPERTOIRE CONTRÔLE D'ACCÈS
REGLAGES
Sélectionner le menu REGLAGES / TYPEDECHARGEMENT.
Sélectionner le mode de téléchargement en intervenant sur les touches ▲▼ . EXEMPLE : RS485
Appuyer sur la touche pour valider la sélection.
TYPE DECHARGEMENT*RS232RS485
TYPE DECHARGEMENT*RS232RS485
TYPE DECHARGEMENTRS232* RS485
La programmation deDÉFAUT est RS232.
Le mode programmé estmarqué par un astérisque à gauche.
Un astérisque s’affiche à gauche de la rubriquesélectionnée.ATTENTION :Pour le téléchargement en mode RS485 se référerau schéma de connexionCA/EN/108 page 74.
AFFICHAGE DESCRIPTIONOPERATION
GROUP S.P.A.
FT SB 08 50
• INLEIDING pag. 51
• 1) FUNCTIE VAN DE TOETSEN pag. 51
• 2) INSTALLEREN VAN DE MODULE pag. 52
• 3) INSTELLEN VAN DE GEWENSTE TAAL pag. 52
3A) De eerste keer dat de module wordt ingeschakeld is er nog geen taal gekozen pag. 52
3B) Wijzigen van de eerder ingestelde taal pag. 52
• 4) ZELFDIAGNOSE pag. 52
• 5) GEBRUIK VAN DE NAAMREGISTERMODULE pag. 53
5A) Bladeren door de namenlijst en oproepen van de gekozen gebruiker pag. 53
5B) Zoeken van een naam in de namenlijst pag. 53
• 6) GEBRUIK VAN DE OPROEPMODULE pag. 54
• 7) BEHEER VAN DE NAMENLIJST pag. 54
7A) Invoeren van een naam pag. 54
7B) Invoeren met art. 1230 pag. 54
7C) Invoeren met behulp van de software, art. 1231/6D pag. 55
7D) Invoeren met behulp van de software, art. 1249 pag. 55
7E) Direct op het toetsenbord invoeren pag. 56
7F) Wijzigen van een naam of een gebruikerscode pag. 56
7G) Wissen van een naam pag. 57
7H) Wissen van een naam met het programmeerapparaat, art. 1230 pag. 58
7I) Wissen van alle in de namenlijst opgeslagen namen pag. 58
7L) Weergave van het aantal in de namenlijst opgeslagen namen,
van de geïnstalleerde softwareversie en van de ID-code pag. 58
• 8) INSTELLEN VAN DE BEDRIJFSMODUS
(STANDAARD OF VIA INDIRECTE CODE) pag. 59
8A) Standaardoproepmode pag. 59
8B) Oproepmode via indirecte code pag. 59
• 9) WIJZIGEN VAN DE SYSTEEMPARAMETERS pag. 60
9A) Instellen van de parameters van de speakerunit, art. 1602-4660
(deuropentijd, gesprekstijd en resettijd) pag. 60
9B) Weergave van de parameters van de speakerunit, art. 1602 – 4660
(deuropentijd, gesprekstijd en resettijd) pag. 60
9C) Instellen van de ID-code pag. 61
• 10) BEHEER VAN DE TOEGANGSCONTROLEFUNCTIE pag. 61
10A) Standaard supercode pag. 61
10B) Wijzigen van de supercode pag. 61
10C) Resetten van de supercode pag. 62
10D) Een paswoord ingeven pag. 62
10E) Een paswoord wissen pag. 62
10F) Alle paswoorden wissen pag. 63
10G) Een paswoord zoeken pag. 64
10H) Bekrachtigen van het deuropeningsrelais door het paswoord in te toetsen pag. 64
10I) Weergave van het aantal opgeslagen paswoorden pag. 65
• 11) INSTELLEN VAN HET TYPE VERBINDING
MET DE PC: RS232 OF RS485 pag. 65
INHOUD
FT SB 08
51 FT SB 08
NE
DE
RL
AN
DS
De Comelit digitale oproepmodule, art. 3340, kan in Simplebussystemen gebruikt
worden en heeft een naamregister voor het opslaan van een lijst van
gebruikersnamen. De module heeft een alfanumeriek toetsenbord waarmee de op het
systeem aangesloten intercomgebruikers opgeroepen kunnen worden door het
huisnummer in te toetsen. De voornaamste kenmerken zijn:
• Geheugencapaciteit: 400 namen van elk maximaal 18 alfanumerieke karakters.
• Grafisch display met een resolutie van 128x64 dots/pitch.
• 2 manieren van oproepen: standaard of door middel van een indirecte code.
• Invoeren van een namenlijst (downloaden) met het programmeerapparaat, art.
1230, of door aansluiting op een pc met software, art.1231/6D, of art.1249.
• Het invoeren van namen door aansluiting op een pc kan via een RS232- of RS485-
kabel geschieden via de interfacekaart, art. 1319 (zie installatieschema
CA_EN_108).
• Ophalen (uploaden) van een in de registermodule opgeslagen namenlijst door
aansluiting op een pc met software, art. 1249.
• Toegangscontrole met opslagcapaciteit voor maximaal 300 paswoorden voor het
bekrachtigen van het relais in de speakermodule dat gewoonlijk als
deuropeningsrelais wordt gebruikt.
• Weergavemogelijkheid van berichten op de grafische interface in een van de 9
beschikbare talen.
1) FUNCTIE VAN DE TOETSEN INLEIDING
OPROEPEN – MENUKEUZE
ACHTERUIT: Bladeren door de gebruikerslijst in dalende alfabetische volgorde
VOORUIT: Bladeren door de gebruikerslijst in oplopende alfabetische volgorde.
NAAM ZOEKEN - MENU VERLATEN
OPROEP – LOKALE DEUROPENER
WISSEN VAN EEN KARAKTER OFANNULEREN VAN EEN OPROEP.
GROUP S.P.A.
FT SB 08 52
BEGINTOESTAND
3) INSTELLEN VAN DE GEWENSTE TAAL
3A) DE EERSTE KEER DAT DE MODULE WORDT INGESCHAKELD, IS ER NOG GEEN TAAL GEKOZEN:
3B) WIJZIGEN VAN DE EERDER INGESTELDE TAAL:
Blader door de lijst met detoetsen ▲▼.Druk op om de gewenste taal te kiezen.
De module staat onderspanning.
* ITALIAANSENGELSFRANS
De STANDAARD instelling is Italiaans, de eerstvolgende keer dat de module weer wordtingeschakeld, wordt opnieuwgevraagd de taal te kiezen.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
BEGINTOESTAND
Zet de spanning op demodule en maak eenverbinding tussen deaansluitingen PR en -.
De module is in de programmeerstand:
om het menu te kiezen▲▼om door de menu's te bladeren
om naar het vorige menu terug te gaan
KIES DE TAAL:* ITALIAANS
ENGELS
TEST BESCHRIJVING
4) ZELFDIAGNOSE
Bij het inschakelen controleert de apparatuur de verbindingen om na te gaan of de communica-tie met speakerunit, art. 1602/4660, en met het toetsenbord van de oproepmodule, art. 3340, inorde is. Indien naast de optie de tekst OK staat, is de test succesvol verlopen. Anders verschijntde tekst MISLUKT. Druk aan het eind van de zelfdiagnosefase op de toets ▼om de module in deruststand te zetten. Hieronder volgt een tabel die de betekenis van de afzonderlijke tests toelicht:
2) INSTALLEREN VAN DE MODULE
Houd u aan de aanwijzingen op het technisch specificatieblad FT/SB/07 of in de techni-sche handleiding MT/SB/02 voor de bekabeling van de module, art. 3340. Om storingendoor elektrostatische ontladingen te voorkomen, wordt aangeraden de behuizing af teschermen zoals aangegeven in het schema op pagina 74.
INITIALISEREN
SPEAKER SERIEEL
MODUS
Controleert de toestand van de EEPROM die de namenlijst vande gebruikers bevat. Als de test mislukt, is de module defect.
Als de test mislukt, moet gecontroleerd worden of de seriëleverbinding met de speakerunit, art. 1602 / 4660, in orde is.
Controleert de aanwezigheid van het alfanumerieke toetsenbordvan art. 3340. Indien de code 3342 naast de beschrijving verschijnt, moet gecontroleerd worden of de verbinding tussen het alfanumerieke toetsenbord en de naamregistermodule in orde is.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
KIES DE TAAL* ITALIAANS
ENGELS
KIES DE TAALITALIAANS*ENGELS
De ingestelde taal wordtaangegeven door eensterretje aan de linkerkant.De STANDAARD instelling is Italiaans, de eerstvolgendekeer dat de module weerwordt ingeschakeld,wordt opnieuw gevraagd detaal te kiezen.
Kies het menuINSTELLINGEN / KIES DE TAAL.
Blader door de lijst met detoetsen ▲▼.Druk op om de gewenste taal te kiezen.
NAMENLIJSTTOEGANGSCONTROLE
INSTELLINGEN
FT SB 08
53 FT SB 08
NE
DE
RL
AN
DS
BEGINTOESTAND
5) GEBRUIK VAN DE NAAMREGISTERMODULE
5A) BLADEREN DOOR DE NAMENLIJST EN OPROEPEN VAN DE GEKOZEN GEBRUIKER
Blader door de gebruikersna-menlijst met de toetsen ▲▼.Druk op de toets omhet menu te verlaten.
Druk op de toets om de gekozen gebruiker op te roepen.
De oproep of het gesprek kan geannuleerdworden door op de toets X te drukken.
De module staat onder spanning en is in de ruststand.
Als er gebruikersnamen in de namenlijst zijn opgeslagen
GIOVANNI ROSSI De namen zijn inalfabetische volgordeopgeslagen.
De oproep is gelukt.
De oproep is mislukt.
Het toestel is bezet.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
VOERHUISNUMMER IN
Gevolgd door:
ZOEK IN LIJST ZOEK NAAM
BEGINTOESTAND
5B) ZOEKEN VAN EEN NAAM IN DE NAMENLIJST
Druk op de toets .
Voer de gebruikersnaam in,eventueel alleen eengedeelte van de achternaam.BIJVOORBEELD: ROSSI
Druk op de toets omde zoekopdracht te starten.
Nu kunt u door de lijst vangebruikersnamen bladerenmet de toetsen ▲▼.
De module staat onderspanning en is in de ruststand.
TOETS NAAM OM TE ZOEKEN
ROS_
ZOEKEN…
ROSSI GIOVANNI
Of:
NAAM NIET OPGESLAGEN IN GEHEUGEN
De gevondengebruikersnaam verschijnt.
De gebruikersnaam komtniet voor op de lijst.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
ZOEK IN LIJST ZOEK NAAM
Gevolgd door:
VOERHUISNUMMER IN
OPROEP UITGEVOERD
Of:
NUMMER NIET GEVONDEN
Of:
NUMMER BEZET
OPROEP UITGEVOERD
Of:
COMMUNICEREN
GROUP S.P.A.
FT SB 08 54
BEGINTOESTAND
6) GEBRUIK VAN DE OPROEPMODULE
BIJVOORBEELD: u wilt degebruiker met de code 1oproepen. Druk op detoets 1 van het alfanu-merieke toetsenbord.
Druk op de toetsof om op te roepen.
De oproep of het gesprek kan geannuleerdworden door op de toets X te drukken.
De module staat onderspanning en is in de ruststand.
BEL NUMMER:_ _ 1
OPROEP UITGEVOERDOf:
NUMMER NIET GEVONDEN
Of:NUMMER BEZET
OPROEP UITGEVOERD Of:
COMMUNICEREN
De oproep is gelukt.
De oproep is mislukt.
Het toestel is bezet.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
ZOEK IN LIJST ZOEK NAAMGevolgd door:
VOER HUISNUMMER IN
BEGINTOESTAND
7B) INVOER MET ART. 1230(niet mogelijk als de oproepmode Indirecte Code actief is, zie Punt 8)
Druk op de toets NAME->van art. 1230.
Toets de naam van degebruiker in, die u in denamenlijst wilt opslaan.BIJVOORBEELD:ROSSI GIOVANNI
Druk op de toets NAME->van art. 1230.
De module staat onderspanning en is in de ruststand.
Als er gebruikers in denamenlijst zijn opgeslagen.
VOER NAAM IN
ROSSI GIOVANNI
CODE: _ _ _
Druk op SHIFT om de onderstefunctie van de toetsen teactiveren. Om de letter aan delinkerkant te wissen drukt u op <.Om speciale tekens in te voeren, dient u de volgendetoetsencombinatie in te drukken:NAME -> + A = ÅNAME -> + B = ÄNAME -> + C = ßNAME -> + O = ÖNAME -> + P = ØNAME -> + Q = ÜDruk op ESC om de invoervan een gebruikersnaam te annuleren.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
VOERHUISNUMMER IN
Gevolgd door:
ZOEK IN LIJST ZOEK NAAM
7) BEHEER VAN DE NAMENLIJST
7A) INVOEREN VAN EEN NAAMEen naam kan in de namenlijst opgeslagen worden met het infrarood-programmeerap-paraat, art. 1230, of met behulp van de software, art. 1231/6D - art.1249, of direct inge-toetst worden op het alfanumerieke toetsenbord van de module.
FT SB 08
55 FT SB 08
NE
DE
RL
AN
DS
BEGINTOESTAND
7C) INVOEREN MET BEHULP VAN DE SOFTWARE ART. 1231/6D
Start de software, art. 1231/6D.Om de software te kunnengebruiken, is het volgende nodig:- Laad de database die de namen
en gebruikerscodes bevat.- Kies de modus
COMPATIBLE in het menu DOWNLOADEN.
- Kies de COM-poort.Druk op de toets DOWNLOADEN.
De module staat onder spanningen is in de ruststand. Sluit dekabel van de software, art.1231/6D, aan op de aansluitk-lemmen TX / RX / - De modules3340 en 3342 mogen niet in deprogrammeerstand zijn.
De namenlijst moet leeg zijn.
Of:
DOWNLOADENMISLUKT
Als het downloaden goedverloopt.
Als er aansluitproblemenzijn.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
GEBRUIKERSCODEINGEVEN
Voer de gebruikerscode in.BIJVOORBEELD: 1
Druk op de ENTER-toets van art. 1230 om de naamen de gebruikerscode in hetgeheugen op te slaan.
U kunt verdergaan met hetinvoeren van de gegevensvan andere gebruikers.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
Na voltooiing van het downloaden DOWNLOADEN GESTOPT
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
BEGINTOESTAND
7D) INVOER MET BEHULP VAN DE SOFTWARE ART. 1249
Start de software, art. 1249.Raadpleeg de online-han-dleiding van het productvoor de vereiste instellingen.Druk op de toets F7 om hetdownloaden te starten.
ATTENTIE: de gekozenoproepmode moet overeen-stemmen met de mode die isingesteld op de module, art. 3340.(zie Punt 8)
Na voltooiing van hetdownloaden.
De module staat onderspanning en is in de rust-stand. Sluit de kabel van desoftware, art. 1249, aan opde aansluitklemmen TX /RX / - De modules 3340 en 3342 mogen niet in deprogrammeerstand zijn.
Of:
DOWNLOADENMISLUKT
DOWNLOADENGESTOPT
Als het downloaden goedverloopt.
Als er aansluitproblemenzijn.
De namenlijst moet leeg zijn.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
VOERHUISNUMMER IN
CODE: _ _ 1
OPSLAAN INGEHEUGEN….
GROUP S.P.A.
FT SB 08 56
BEGINTOESTAND
7E) DIRECT OP HET TOETSENBORD INVOEREN(niet mogelijk als de oproepmode Indirecte Code actief is, zie Punt 8)
Kies het menu NAMENLIJST / NAMENINVOEREN / HANDMATIG.
Voer vervolgens de gebruikersnaam in.BIJVOORBEELD:ROSSI GIOVANNI
Druk op de toets omde gebruikerscode in tevoeren.BIJVOORBEELD: 1
Druk op de toetsom de gebruikersnaam en -code op te slaan.
U kunt verdergaan met hetinvoeren van de gegevensvan andere gebruikers.
Zet de spanning op demodule en maak eenverbinding tussen deaansluitingen PR en -.
De module is in de programmeerstand:
om het menu te kiezen▲▼om door de menu's te bladeren
om naar het vorige menu terug te gaan
_
ROSSI GIOVANNI _
CODE: _ _ 1
OPSLAANIN GEHEUGEN…
Of:NAAM REEDSIN GEHEUGEN
_
De module is gereed voorhet invoeren van namen.
Om de letter links van decursor te wissen, drukt u opde toets X, voor specialetekens op de toets 9 . , :
Als de gebruikersnaam al in het geheugen is opgeslagen.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
NAMENLIJST TOEGANGSCONTROLE
INSTELLINGEN
BEGINTOESTAND
7F) WIJZIGEN VAN EEN NAAM OF EEN GEBRUIKERSCODE(niet mogelijk als de oproepmode Indirecte Code actief is, zie Punt 8)
Kies het menu NAMENLIJST / NAMENWIJZIGEN.
Voer de gebruikersnaam in die u wilt wijzigen, eventueel alleeneen gedeelte van de achter-naam. BIJVOORBEELD: ROSS
Druk op de toets om het zoeken van de gebruikersnaam te starten.
Gebruik de toetsen ▲▼
om door de lijst van gebruik-ers te bladeren. Kies degebruikersnaam die u wiltwijzigen. BIJVOORBEELD:ROSSI GIOVANNI
Druk op de toets omover te gaan tot het wijzigenvan de gebruikersnaam.
Zet de spanning op demodule en maak eenverbinding tussen deaansluitingen PR en -.
De module is in de programmeerstand:
om het menu te kiezen▲▼om door de menu's te bladeren
om naar het vorige menu terug te gaan
VOER EEN DEELVAN DE NAAM
IN
ROSS _
ZOEKEN...
ROSSI GIOVANNI
ROSSI GIOVANNI _
U wordt verzocht degebruikersnaam in te voeren die u wilt wijzigen.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
NAMENLIJST TOEGANGSCONTROLE
INSTELLINGEN
FT SB 08
57 FT SB 08
NE
DE
RL
AN
DSBEGINTOESTAND
7G) WISSEN VAN EEN NAAM (niet mogelijk als de oproepmode Indirecte Code actief is, zie Punt 8)
Zet de spanning op demodule en maak eenverbinding tussen deaansluitingen PR en -.
De module is in de programmeerstand:
om het menu te kiezen▲▼om door de menu's te bladeren
om naar het vorige menu terug te gaan
NAMENLIJST TOEGANGSCONTROLE
INSTELLINGEN
Wijzigen van de naam met behulp van het alfanumerieke toetsenbord.
Druk op de toets omover te gaan tot het wijzi-gen van de gebruikerscode.
Wijzigen van de code met behulp van het alfanumerieke toetsenbord.
Druk op de toets om de gebruikersnaam en -code op te slaan.
U kunt verdergaan met hetwijzigen van de gegevensvan een andere gebruiker.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
ROSSI GIOVANN _
CODE: _ _ 1
CODE _ _ 2
OPSLAANIN GEHEUGEN…
Of:NAAM REEDS IN
GEHEUGEN BESCHRIJVING
Kies het menu NAMENLIJST / NAMEN WISSEN
Voer de gebruikersnaam in die u wilt wissen,eventueel een gedeelte van de achternaam.BIJVOORBEELD: ROSS
Druk op de toets om het zoeken van de gebruikersnaam te starten.
Gebruik de toetsen ▲▼
om door de lijst vangebruikers te bladeren.Kies de gebruikersnaamdie u wilt wissen.BIJVOORBEELD:ROSSI GIOVANNI
Druk op de toets om over te gaan tot het wissen van de gebruikersnaam.
U kunt verdergaan met het wissen van een andere gebruikersnaam.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
VOER EEN DEEL
VAN DE NAAM IN
ROSS _
ZOEKEN…
ROSSI GIOVANNI
WISSEN…
U wordt verzocht degebruikersnaam in tevoeren die u wilt wissen.
GROUP S.P.A.
FT SB 08 58
BEGINTOESTAND
7H) WISSEN VAN EEN NAAM MET HET PROGRAMMEERAPPARAAT, ART. 1230(niet mogelijk als de oproepmode Indirecte Code actief is, zie Punt 8)
Kies de gebruikersnaamdie u wilt wissen door metde toetsen ▲▼ door denamenlijst te bladeren.
Druk op de toets NAME <- van art. 1230.
Druk op de toets ENTERvan art. 1230 om het wissen te bevestigen.
De module staat onderspanning en is in de ruststand.
Als er gebruikers in denamenlijst zijn opgeslagen.
GIOVANNI ROSSI
NAAM WISSEN ?
WISSEN….
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
VOERHUISNUMMER IN
Gevolgd door:ZOEK IN LIJST ZOEK NAAM
BEGINTOESTAND
7I) WISSEN VAN ALLE IN DE NAMENLIJST OPGESLAGEN NAMEN
Zet de spanning op demodule en maak eenverbinding tussen deaansluitingen PR en -.
De module is in de programmeerstand:
om het menu te kiezen▲▼om door de menu's te bladeren
om naar het vorige menu terug te gaan
NAMENLIJST TOEGANGSCONTROLE
INSTELLINGEN
Kies het menu NAMENLIJST / WIS ALLE NAMEN
Druk op de toets om alle gebruikersnamen in de lijst te wissen.Druk op de toets omhet wissen te annuleren.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
ALLE NAMEN WISSEN?
WISSEN….
BEGINTOESTAND
7L) WEERGAVE VAN HET AANTAL IN DE NAMENLIJST OPGESLAGEN NAMEN,VAN DE GEÏNSTALLEERDE SOFTWAREVERSIE EN VAN DE ID-CODE
Kies het menu INFO.
Zet de spanning op demodule en maak eenverbinding tussen deaansluitingen PR en -.
De module is in de programmeerstand:
om het menu te kiezen▲▼om door de menu's te bladeren
om naar het vorige menu terug te gaan
Comelit
REV. 1.5NAMEN OPGESL: 0ADRES RS485: 255
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
NAMENLIJST TOEGANGSCONTROLE
INSTELLINGEN
FT SB 08
59 FT SB 08
NE
DE
RL
AN
DS
8) INSTELLEN VAN DE BEDRIJFSMODUS(Standaard of met Indirecte Code)
8A) STANDAARD OPROEPMODE (fabrieksinstelling)In deze bedrijfsmodus wordt de gebruiker van het intercomsysteem geïdentificeerd dooreen veld Gebruikersnaam en een veld Code.BIJVOORBEELD: Gebruikersnaam = Rossi; Code = 1De oproep kan op de volgende wijzen geschieden:1) Kies de gebruiker Rossi met de toetsen ▲▼ ➔ , druk op de toets ➔ waarna de
oproep wordt gezonden naar de gebruiker met de code 1. 2) Geef de code 1 ➔ in via het toetsenbord en druk op de toets .
8B) OPROEPMODE MET INDIRECTE CODE In deze bedrijfsmodus wordt de gebruiker van het intercomsysteem geïdentificeerd doorde velden Indirecte Code, Gebruikersnaam (optioneel) en Code.BIJVOORBEELD: Gebruikersnaam = Rossi; Code = 1; Indirecte Code = 100De oproep kan op de volgende wijzen geschieden:1) Kies de gebruiker Rossi met de toetsen ▲▼ ➔ , druk op de toets ➔ waarna de
oproep wordt gezonden naar de gebruiker met de code 1.2) Geef via het toetsenbord de indirecte code 100 ➔ in, druk op de toets ➔ , waarna
de oproep wordt gezonden naar de gebruiker met de code 1.
Het downloaden van een lijst met de bijbehorende velden is alleen mogelijk met behulpvan de software art. 1249.De indirecte code kan maximaal uit 6 cijfers bestaan.Het veld Gebruikersnaam kan ook weggelaten worden (zie "Oproep met Indirecte Codezonder naamveld" in de online-handleiding van art. 1249).Voor het actualiseren van een module waarin reeds een namenlijst is opgeslagen, moeteerst de aanwezige lijst in zijn geheel worden gewist volgens de procedure die isbeschreven onder "WISSEN VAN ALLE IN DE NAMENLIJST OPGESLAGEN NAMEN".
BEGINTOESTAND
Om de standaardoproepmode of de mode met Indirecte Code te kiezen, moet devolgende procedure worden gevolgd:
Kies het menu INSTELLINGEN / BELLEN
Kies de gewenste oproepmode met de toetsen ▲▼.
Druk op de toets omuw keus te bevestigen.
Zet de spanning op demodule en maak eenverbinding tussen deaansluitingen PR en -.
De module is in de programmeerstand:
om het menu te kiezen▲▼om door de menu's te bladeren
om naar het vorige menu terug te gaan
OPROEPMODE* STANDAARD
AANGEPASTE CODE
OPROEPMODE* STANDAARD
AANGEPASTE CODE
OPROEPMODESTANDAARD
*AANGEPASTE CODE
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
NAMENLIJST TOEGANGSCONTROLE
INSTELLINGEN
GROUP S.P.A.
FT SB 08 60
9) WIJZIGEN VAN DE SYSTEEMPARAMETERS
9A) INSTELLEN VAN DE PARAMETERS VAN DE SPEAKERUNIT 1602-4660(deuropentijd , gesprekstijd en resettijd. Met resettijd wordt het tijdsverloop bedoeld tussenhet beëindigen van een gesprek en de mogelijkheid een nieuw gesprek te beginnen).
BEGINTOESTAND
Druk op de toets om het menu INSTELLINGEN /SYSTEEMPARAMETERS /SPEAKER PARAMETERSte kiezen.
Kies de parameter die u wiltwijzigen. BIJVOORBEELD:gesprekstijd.
Wijzig de waarde van deparameter door op de toet-sen ▲▼te drukken; drukop de toets om dewijziging te annuleren.
De module, art. 3340,wordt gevoed via het aftakblokje PR dat isaangesloten op hetaftakblokje - .
Zet de spanning op de module 1602 / 4660 enmaak een verbinding tussende aansluitingen PR en -.
De module is in de programmeerstand:
om het menu te kiezen▲▼om door de menu's te bladeren
om naar het vorige menu terug te gaan
De module is in de programmeerstand
VOER GESPREKSTIJD INVOER DEUROPENTIJD IN
VOER RESETTIJD IN
VOER GESPREKSTIJD INVOER DEUROPENTIJD IN
VOER RESETTIJD IN
GETAL IN SEC. 010 Toegestane waarden:Gesprekstijd: 10 tot 180 sec.Deuropentijd: 1 tot 99 sec.Resettijd: 0 tot 10 sec.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
NAMENLIJST TOEGANGSCONTROLE
INSTELLINGEN
Bevestig de waarde doorop de toets te drukken.
PARAMETERGEWIJZIGD
U hoort een bevestigingtoonop de speakerunit, art. 1602/4660.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
9B) WEERGAVE VAN DE PARAMETERS VAN DE SPEAKERUNIT, ART. 1602 – 4660(deuropentijd , gesprekstijd en resettijd)
BEGINTOESTAND
Kies het menuINSTELLINGEN / SYSTEEMPARAMETERS /SPEAKERPARAMETERS /BEKIJKEN
De module, art. 3340,wordt gevoed via het aftak-blokje PR dat is aanges-loten op het aftakblokje - .
De module, art. 1602 / 4660,wordt gevoed via het aftak-blokje PR dat is aangeslotenop het aftakblokje - .
De module is in de programmeerstand:
om het menu te kiezen▲▼om door de menu's te bladeren
om naar het vorige menu terug te gaan
GESPREKSTIJD 60DEUROPENTIJD 01WACHTTIJD 10
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
NAMENLIJSTTOEGANGSCONTROLE
INSTELLINGEN
De op de speakerunit, art. 1602/4660, ingesteldeparameters worden getoond.
ATTENTIE: Deze functie geldt alleenvoor speakerunits die zijnuitgerust met softwareversie2.0 of hoger.
FT SB 08
61 FT SB 08
NE
DE
RL
AN
DS
10) BEHEER VAN DE TOEGANGSCONTROLEFUNCTIE
10A) STANDAARD SUPERCODE
De supercode geeft toegang tot alle functies zoals INGEVEN, WISSEN en ZOEKEN vaneen paswoord, en kan het relais van de speakerunit bekrachtigen, dat gewoonlijk alsdeuropeningsrelais wordt gebruikt.
10B) WIJZIGEN VAN DE SUPERCODE (standaard = 778899 ) 9C) INSTELLEN VAN DE ID-CODE (standaard = 255 )De ID-code wordt alleen in speciale gevallen gebruikt.
BEGINTOESTAND
Kies het menu INSTELLINGEN / SYSTEEMPARAMETERS /ADRES RS485.
Druk op de toets om uw keus te bevestigen.
Druk op de toetsen ▲▼
om de waarde van de ID-code te wijzigen.
Druk op de toets om de waarde op te slaan.
De module, art. 3340,wordt gevoed via het aftakblokje PR dat is aangesloten op het aftakblokje - .
De module is in de programmeerstand:
om het menu te kiezen▲▼om door de menu's te bladeren
om naar het vorige menu terug te gaan
ADRES RS485: 01
ADRES RS485: 01
ADRES RS485: 254
PARAMETERGEWIJZIGD
De getoonde ID-codeis niet de geconfigureerdecode.
De getoonde ID-code is nietde geconfigureerde code.
De code kan een getal zijntussen 1 en 255.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
NAMENLIJST TOEGANGSCONTROLE
INSTELLINGEN
BEGINTOESTAND
Kies het menu TOEGANGSCONTROLE /SUPERCODE / VOEG NIEUWE TOE.
De op dit moment ingesteldesupercode invoeren. Dezemoet uit 6 cijfers bestaan.
Druk op de toets om de invoer te bevestigen.
De nieuwe supercodeingeven. Deze moet uit 6cijfers bestaan.
Druk op de toets omde invoer te bevestigen.
Zet de spanning op de module en maak eenverbinding tussen deaansluitingen PR en -.
De module is in de programmeerstand:
om het menu te kiezen▲▼om door de menu's te bladeren
om naar het vorige menu terug te gaan
Als de ingegeven supercodeovereenkomt met de in hetgeheugen opgeslagen supercode.
Als de ingegeven supercode niet overeenkomt met de in hetgeheugen opgeslagen supercode.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
NAMENLIJST TOEGANGSCONTROLE
INSTELLINGEN
SUPERCODE GEBRUIKT:_ _ _ _ _ _
SUPERCODE GEBRUIKT:* * * * * *
NIEUWE SUPERCODE:_ _ _ _ _ _
Of:
SUPERCODE VERKEERDE
NIEUWE SUPERCODE:* * * * * *
SUPERCODE GEWIJZIGD
GROUP S.P.A.
FT SB 08 62
10C) RESETTEN VAN DE SUPERCODE
BEGINTOESTAND
Kies het menuTOEGANGSCONTROLE /SUPERCODE / RESETTEN
Zet de spanning op demodule en maak eenverbinding tussen deaansluitingen PR en -.
De module is in de programmeerstand:
om het menu te kiezen▲▼om door de menu's te bladeren
om naar het vorige menu terug te gaan
SUPERCODE GEWIJZIGD
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
NAMENLIJST TOEGANGSCONTROLE
INSTELLINGEN
De supercode wordtteruggezet op destandaardwaarde (778899).
10E) WISSEN VAN EEN PASWOORD BEGINTOESTAND
BEGINTOESTAND
Kies het menu TOEGANGSCONTROLE /PASWOORD
Zet de spanning op demodule en maak eenverbinding tussen deaansluitingen PR en -.
De module is in de programmeerstand:
om het menu te kiezen▲▼om door de menu's te bladeren
om naar het vorige menu terug te gaan
SUPERCODE GEBRUIKT:_ _ _ _ _ _
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
NAMENLIJST TOEGANGSCONTROLE
INSTELLINGEN
10D) EEN PASWOORD INGEVEN (Standaard = geen paswoord in het geheugen opgeslagen)
BEGINTOESTAND
Kies het menu TOEGANGSCONTROLE /PASWOORD
Geef de supercode in.
Zet de spanning op demodule en maak eenverbinding tussen deaansluitingen PR en -.
De module is in de programmeerstand:
om het menu te kiezen▲▼om door de menu's te bladeren
om naar het vorige menu terug te gaan
SUPERCODE GEBRUIKT:_ _ _ _ _ _
SUPERCODE GEBRUIKT:* * * * * *
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
NAMENLIJST TOEGANGSCONTROLE
INSTELLINGEN
Druk op de toets omde invoer te bevestigen.
Kies het menu INVOEREN.
Geef het gewenste paswoord in.
Druk op de toets omde invoer te bevestigen.
U kunt verdergaan met het invoeren vanandere paswoorden.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
VOERWIS
ZOEK
VOER PASWOORD :_ _ _ _ _ _
VOER PASWOORD :* * * * * *
OPSLAAN INGEHEUGEN…
VOER PASWOORD :_ _ _ _ _ _
Het menu voor het beheer vanpaswoorden voor het openenvan de deur verschijnt.
Het paswoord kan uit 1 tot 6 karakters bestaan.
FT SB 08
63 FT SB 08
NE
DE
RL
AN
DS
10F) ALLE PASWOORDEN WISSEN
BEGINTOESTAND
Kies het menu TOEGANGSCONTROLE /PASWOORD
Geef de supercode in.
Druk op de toets om de invoer te bevestigen.
Kies het menu WISSEN.
Druk op de toets om van alle paswoorden te bevestigen.
Zet de spanning op demodule en maak eenverbinding tussen deaansluitingen PR en -.
De module is in de programmeerstand:
om het menu te kiezen▲▼om door de menu's te bladeren
om naar het vorige menu terug te gaan
SUPERCODE GEBRUIKT:_ _ _ _ _ _
SUPERCODE GEBRUIKT:* * * * * *
VOERWIS
ZOEK
ALLE PASWOORDEN WISSEN?
WISSEN…
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
NAMENLIJST TOEGANGSCONTROLE
INSTELLINGEN
U wordt verzocht de supercode in te voeren.
Het menu voor het beheervan paswoorden voor het openen van de deur verschijnt.
Geef de supercode in.
Druk op de toets om de invoer te bevestigen.
Voer het menu WISSEN.
Druk op de toets om uw keus te bevestigen.
Geef het paswoord in dat u wilt wissen.
Druk op de toets om deinvoer te bevestigen.
U kunt verdergaan met het wissen van andere paswoorden.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
SUPERCODE GEBRUIKT :* * * * * *
VOER WIS
ZOEK
VOER INWIS
ZOEK
WIS PASWOORD:_ _ _ _ _ _
WIS PASWOORD:* * * * * *
WISSEN…
Of:WIS PASWOORD:
X X X X X X
WIS PASWOORD:_ _ _ _ _ _
Het menu voor het beheer vanpaswoorden voor het openenvan de deur verschijnt.
Als het paswoord in de lijst is gevonden.
Als het paswoord niet isgevonden, wordt eenpaswoord met gelijke waardegetoond. U kunt door de lijstmet opgeslagen paswoordenbladeren met de toetsen▲▼;druk op de toets om hetgekozen paswoord te wissen.
GROUP S.P.A.
FT SB 08 64
10G) EEN PASWOORD ZOEKEN
BEGINTOESTAND
Kies het menu TOEGANGSCONTROLE /PASWOORD.
Geef de supercode in.
Druk op de toets om de invoer te bevestigen.
Kies het menu ZOEK.
Voer het paswoord in dat u zoekt.BIJVOORBEELD:112233
Druk op de toets om de invoer te bevestigen.
Zet de spanning op demodule en maak eenverbinding tussen deaansluitingen PR en -.
De module is in de programmeerstand:
om het menu te kiezen▲▼om door de menu's te bladeren
om naar het vorige menu terug te gaan
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
NAMENLIJST TOEGANGSCONTROLE
INSTELLINGEN
Het menu voor het beheer van paswoorden voor hetopenen van de deur verschijnt.
Het gezochte paswoordwordt getoond, of eenpaswoord van gelijke waardedat in de lijst is opgeslagen.
U kunt de lijst met opgeslagen paswoordenoproepen met de toetsen ▲▼.
ZOEK PASWOORD:112244
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
De paswoorden zijn in oplopende volgordeopgeslagen.
BEGINTOESTAND
10H) BEKRACHTIGEN VAN HET DEUROPENINGSRELAIS DOOR HET PASWOORD IN TE TOETSEN
Druk op de toets .
Toets het paswoord in.
Druk op de toets .
De module staat onder spanning en isin de ruststand.
Als er gebruikers in denamenlijst zijn opgeslagen.
VOER PASWOORD :_ _ _ _ _ _
VOER PASWOORD :* * * * * *
PASWOORDBEVESTIGD
Of:
VERKEERDPASWOORD
U wordt verzocht het paswoord in te geven.
Als de code in het geheugenis opgeslagen, wordt hetrelais in de speakerunit, art.1602 / 4660, bekrachtigd.
Als de code niet in hetgeheugen is opgeslagen.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
VOERHUISNUMMER IN
Gevolgd door:
ZOEK IN LIJST ZOEK NAAM
SUPERCODE GEBRUIKT:_ _ _ _ _ _
SUPERCODE GEBRUIKT:* * * * * *
VOERWIS
ZOEK
ZOEK PASWOORD:_ _ _ _ _ _
ZOEK PASWOORD:* * * * * *
ZOEK PASWOORD:112233
FT SB 08
65 FT SB 08
NE
DE
RL
AN
DS
10I) WEERGAVE VAN HET AANTAL OPGESLAGEN PASWOORDEN
BEGINTOESTAND
Zet de spanning op demodule en maak eenverbinding tussen deaansluitingen PR en -.
De module is in de programmeerstand:
om het menu te kiezen▲▼om door de menu's te bladeren
om naar het vorige menu terug te gaan
NAMENLIJST TOEGANGSCONTROLE
INSTELLINGEN
Kies het menu TOEGANGSCONTROLE /INFO.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
Comelit PASWOORDENINGEVRD: 1
Het aantal opgeslagen paswoordenwordt getoond.
11) INSTELLEN VAN HET TYPE VERBINDING MET DE PC, RS232 of RS485 (standaard = RS232)
BEGINTOESTAND
Zet de spanning op demodule en maak eenverbinding tussen deaansluitingen PR en -.
De module is in de programmeerstand:
om het menu te kiezen▲▼om door de menu's te bladeren
om naar het vorige menu terug te gaan
NAMENLIJSTTOEGANGSCONTROLE
INSTELLINGEN
Kies het menu INSTELLINGEN / TYPE DOWNLOAD
Kies het type downloaddoor te drukken op detoetsen ▲▼. BIJVOORBEELD: RS485
Druk op de toets om uw keus te bevestigen.
TYPE DOWNLOAD*RS232RS485
TYPE DOWNLOAD *RS232RS485
TYPE DOWNLOADRS232* RS485
De STANDAARD instelling is RS232.
Het ingestelde type wordtaangegeven door eensterretje aan de linkerkant.
Aan de linkerkant van de gekozen optie verschijnteen sterretje.ATTENTIE:Zie voor het downloaden via RS485 hetaansluitschema CA/EN/108op pagina 74.
WEERGAVE OP HET DISPLAY BESCHRIJVINGACTIE
GROUP S.P.A.
FT SB 08 66
DIAGRAMMA MENU. I
GESTIONE RUBRICAINSERIMENTO NOMI
MANUALEVALORE :
CANCELLAZIONE NOMIVALORE :
MODIFICA NOMIVALORE :
AZZERA TUTTI I NOMI
CONTROLLO ACCESSISUPERCODICE
INSERISCI NUOVOVALORE:
AZZERA
PASSWORDINSERISCI
VALORE :
CANCELLAVALORE :
TROVAVALORE :
AZZERA
INFO
FT SB 08
67 FT SB 08
IMPOSTAZIONITIPO DOWNLOAD
VALORE :
PARAMETRI IMPIANTOPARAMETRI PORTER
INS. TEMPO FONICAVALORE
INS. TEMPO APRIP.VALORE
INS. TEMPO RESETVALORE
VISUALIZZA
INDIRIZZO RS485
SCEGLI LINGUAVALORE :
GEST. CHIAMATAVALORE :
AZZERA
INFO
GROUP S.P.A.
FT SB 08 68
MENU DIAGRAM.GB
NAME DIRECTORYENTERING NAMES
MANUALLYVALUE :
DELETING NAMESVALUE :
CHANGE NAMESVALUE :
DELETE ALL NAMES
ACCESS CONTROLSUPERCODE
ENTER NEW ONEVALUE :
DELETE
PASSWORDENTER
VALUE :
DELETEVALUE :
SEARCHVALUE :
DELETE
INFO
FT SB 08
69 FT SB 08
SETTINGSTYPE OF DOWNLOAD
VALUE :
SYSTEM PARAMETERSSPEAKER PARAMETERS
ENT. AUDIO TIMINGVALUE :
ENT. DOOR LOCK TIMEVALUE :
ENTER RESET TIMEVALUE :
VIEWING
ADDRESS RS485
SELECT LANGUAGEVALUE :
CALL OPERATINGVALUE :
DELETE
INFO
GROUP S.P.A.
FT SB 08 70
DIAGRAMME MENU.F
REPERTOIRINTRODUIR NOMS
MANUELVALEUR :
EFFACER NOMSVALEUR :
CHANGER NOMSVALEUR :
EFFACER LES NOMS
CONTROL D'ACCESSUPERCODE
INTRODUIR NOUVEAUVALEUR :
EFFACER
PASSWORDINTRODUIR
VALEUR :
EFFACERVALEUR :
TROUVERVALEUR :
EFFACER
INFO
FT SB 08
71 FT SB 08
REGLAGESTYPE DECHARGEMENT
VALEUR :
PARAMETRES SYST.PARAMETRES HP
ENT. TEMPS AUDIOVALEUR :
ENT. TEMPS OUVREP.VALEUR :
ENT. TEMPS RESETVALEUR :
VISUALISER
ADRESSE RS485
CHOISIR LANGUEVALEUR :
GESTION APPELVALEUR :
EFFACER
INFO
GROUP S.P.A.
FT SB 08 72
MENUSCHEMA (Onderschrift bij tekening: enkelvoudige getwiste kabel. bijvoorbeeld belden 9505).NL
NAMEN LIJSTNAMEN INVOEREN
HANDMATIGGETAL :
NAMEN WISSENGETAL :
NAMEN WIJZIGENGETAL :
WIS ALLE NAMEN
TOEGANGSCONTROLESUPERCODE
VOEG NIEUWE TOEGETAL :
WISSEN
PASSWOORDVOER
GETAL :
WISGETAL :
ZOEKGETAL :
WISSEN
INFO
FT SB 08
73 FT SB 08
INSTELLINGENTYPE DOWNLOAD
GETAL :
SYSTEEM PARAMET.SPEAKER PARAMETRS
VOER GESPREKST. INGETAL :
VOER DEUROPENT. INGETAL :
VOER RESETT. INGETAL :
BEKIJKEN
ADRES RS485
KIES DE TAALGETAL :
BELLENGETAL :
WISSEN
INFO
GROUP S.P.A.
FT SB 08 74
CA/EN/108
Schema di collegameto articolo.
Article connection diagram.
Schéma de connexion article
Aansluitschema voor het artikel.
ATTENZIONE- È POSSIBILE UTILIZZARE AL MASSIMO 5 TERMINALI ART. 3340-3342- DISTANZA MASSIMA TRA L’ART. 1319 ED IL TERMINALE ART. 3340-3342 PIÙ DISTANTE: 100 m
ATTENTION- IT IS POSSIBLE TO USE A MAXIMUM OF 5 TERMINALS ART. 3340-3342- MINIMUM DISTANCE BETWEEN ART. 1319 AND TERMINAL ART. 3340-3342 FURTHEST AWAY: 100 m
ATTENTION- POSSIBILITÉ D’UTILISER AU MAXIMUM 5 MODULES TERMINAUX ART. 3340 - 3342- DISTANCE MAXIMUM ENTRE L’ART. 1319 ET LE MODULE TERMINAL ART. 3340 – 3342 LE PLUS ÉLOIGNÉ : 100 mètres.
ATTENTIE- ER KUNNEN MAXIMAAL 5 TERMINALS, ART. 3340-3342, WORDEN GEÏNSTALLEERD- MAXIMALE AFSTAND VAN ART. 1319 TOT DE VERST VERWIJDERDE TERMINAL, ART. 3340-3342: 100 m
COMPUTERCOMPUTERORDINATEURCOMPUTER
TRECCIA TELEFONICASCHERMATA
SCREENED PLAITEDTELEPHONE CABLE
TRESSETÉLÉPHONIQUE BLINDÉE
GETWISTE EN AFGESCHERMDEKABEL DOORSN
ART. 1319
Impostare il jumper JP1 in modalità “MODO 1” (vedi figura)
Set jumper JPI in “MODE 1” mode (see figure)
Programmer le jumper JP1 en "MODE 1" (voir figure).
Stel de jumper JP1 in op "MODUS 1" (zie de afbeelding)
I
GB
F
NL
FT SB 08
75 FT SB 08
Note - Notes - Note - Opmerking
GROUP S.P.A.
FT SB 08 76
Note - Notes - Note - Opmerking
FT SB 08
77 FT SB 08
Note - Notes - Note - Opmerking
Comelit Group S.p.A. - Via Don Arrigoni 5 - 24020 Rovetta S. Lorenzo BG Italy - tel. (+39) 0346 750 011 - fax (+39) 0346 71436www.comelit.it [email protected] [email protected] [email protected]
FT
/SB
/08
- 1a
ediz
ione
01/
2006
- c
od.
2259
0524
15, Rue Jean Zay69800 Saint Priest
Tel 04 72 28 06 56 - Fax 04 72 28 83 29http://www.comelit.fr
E-mail: [email protected] F
Aventurijn 2203316LB Dordrecht
Tel 078 65 11 201 - Fax: 078 61 70 955 http://www.comelit.nl
E-mail: [email protected] NL
Josef Estivill 67/6908027 Barcelona
Tel. 932 430 376 - Fax 934 084 683http://www.comelit.es
E-mail: [email protected] E
Chaussée de Ninove, 900 - 1703 Schepdaal (Dilbeek)Ninoofsesteenweg, 900 - 1703 Schepdaal (Dilbeek)
Tel 02 411 50 99 - Fax 02 411 50 97http://www.comelit.be
E-mail: [email protected] B
1 Brownfields - Welwyn Garden CityHERTS - AL7 1AN
Tel 01707 377203 - Fax 01707 377204http://www.comelitgroup.co.uk
E-mail: [email protected] UK SG
SINGAPORE REPRESENTATIVE OFFICE 53 Meyer Road - Meyer Tower #19-00
Singapore 437878 Tel:+65-6440 5857 - Fax: +65 6440 5136
E-mail: [email protected]