General Water SystemsCleanSweep Product Report
____________________________________________________________________________________PROJECT INFORMATION:Date - Nov 04, 2021GWS Report ID - GWS110421400292TProject Name - JM SmuckersProject Address - Project City, State - Pasco, WA Generated By - Dan DanielAffiliation - All Products Rep, Employee, Regional ManagerGWS Rep - General Water SystemsRep Contact - Dan DanielEngineer - Eng. Contact - ____________________________________________________________________________________DESIGN INFORMATION:Design Basis: Tower Flow RateDesign Flow Rate: 4800 GPMSystem Selected: CLEANSWEEP sized with a 15 % Side Stream
Selected WAVE:Selected SEPARATOR: GLS501D-HH-AC-4-MBV-B-V-PEBasin Area: 0 Sq. Ft. No. of Cells in Basin: 4For a flow rate of 720 GPM for the Separator____________________________________________________________________________________SELECTED OPTIONS: SEPARATOR
Body Style: AccessiblePanel Enclosure: NEMA 4Voltage: 460 VAC 3 ph 60 HzPremium Motor: YesMotorized Purge Valve: MBV
____________________________________________________________________________________SELECTED ACCESSORIES:
System Packaging Not Included
Equipment Warranty: Standard____________________________________________________________________________________
General Water SystemsCleanSweep Product Report Page 2
____________________________________________________________________________________EQUIPMENT DESCRIPTIONS:
GLS501D-HH-AC-4-MBV-B-V-PECentrifugal Separator SystemSeparator Purge, Motorized Ball ValveNEMA 4 Panel, 460 VAC 3 ph 60 Hz40 Feet TDHAccessible SeparatorSuction StrainerIsolation ValvesPremium Efficiency Motor 10 HP
CleanSweepSweeper design, all tower internal headers, manual flow control valve, and header pressure gauge are included.Interconnecting piping between the filtration skid and cooling tower and any required tower isolation orequalization valves to be provided by others.
____________________________________________________________________________________NOTES: One CleanSweep system to handle all cells Included is the custom sweeper piping system with the skid ____________________________________________________________________________________1. Lead time for equipment listed on pricing summary page.
CLEANSWEEP – MANUFACTURER’S NOTES
1
Field Wiring and Installation - Field wiring to and installation of the proposed CleanSweep water treatment equipment shall be by others and is not included in this proposal. This includes setting and installing all equipment, all required interconnecting piping, sweeper system piping, valves, couplings, conduit and electrical service connections required for a fully operating system.
2 Sweeper Piping Layout – Each sweeper system is designed to fit in the proposed tower. Drawings will be finalized
after receipt of order when tower model numbers are confirmed. Please allow 3 to 4 weeks for receipt of sweeper system drawing layout.
3 Proposal Only - This is a Proposal only and not an offer to sell. Any order resulting from this Proposal is subject to
acceptance by Manufacturer under its usual terms of sale. Taxes are not included. Errors are subject to correction.
4 Orders - Orders should be emailed [email protected]. Please refer to the Proposal Number when ordering.
Section 6, Page 1
Note: Dimensions are approximate and are for reference only. Dimensions subject to change without notice. Weights are approximate.
SIZING AND SELECTIONCSS SIDE STREAM PUMP FLOW RATE
(FOR LOW HEAD “LH” PUMP STYLE ONLY)
GWS RECOMMENDS 10-15% SIDE STREAM FILTRATION• CSS: Separator with automatic purge to waste with a MBV (Motorized Ball Valve), control panel, and pump/motor. There is loss
of water with every cycle. Comes with a standard cycle timer.
• LH: Low head pump booster package. Side stream to main cooling tower system pump.
NOT INTENDED FOR USE WITH SWEEPER PIPING.
Listed in the order of preferred calculation method to be used:
1. When you have the cooling tower GPM only (the tonnage, the model number, or the basin size are not available).
Example ~ A GPM of 2800 at 15% side stream equals 420 calculated GPM.
Selection is based on the GPM of the system that is closest to the calculated GPM, or the customer’s tolerance for any extra
horsepower in yearly consumption. The cost of the system may become a factor when you decide whether or not to purchase the
next larger sized package. Example ~ Series 401 (420 GPM)
2. When you have the tonnage only (the model number, the basin size, or the cooling tower fl ow rate are not available).
Example ~ 200 ton x 3* = 600 calculated GPM; 600 calculated GPM at 15 % side stream equals 90 GPM.
* 3 GPM/ton is based upon the nominal open loop tower conditions of 95/85/78 degrees F.
Selection is based on the GPM of the system that is closest to the calculated GPM, or the customer’s tolerance for any extra
horsepower in yearly consumption. The cost of the system may become a factor when you decide whether or not to purchase the
next larger sized package: Example ~ Series 201 (115 GPM)
3. When you have the model number only (the cooling tower GPM, the tonnage, or the basin size are not available).
Refer to the manufacturer’s literature to obtain the GPM.
Example ~ Select nominal temperature. Hot water is 95°F; cold water 85°F; and wet bulb is 78°F. A GPM of 1017 for Marley Model
# NC8304F 95/85/78 cooling tower at 15% side stream equals 152.5 calculated GPM.
Selection is based on the GPM of the system that is closest to the calculated GPM, or the customer’s tolerance for any extra
horsepower in yearly consumption. The cost of the system may become a factor when you decide whether or not to purchase the
next larger sized package: Example ~ Series 251 (160 GPM)
SEPARATOR SYSTEMS SELECTION CHART
SEPARATOR
SIZE
NOMINAL FLOW HIGHER FLOW
SERIES FLOW (GPM) SERIES FLOW (GPM)
1” 101-LH 30
1-1/4” 121-LH 50
1-1/2” 151-LH 68
2” 201-LH 115
2-1/2” 251-LH 160
3” 300-LH 200
4” 400-LH 340 401-LH 420
5” 500-LH 525
6” 600-LH 825 601-LH 1100
8” 800-LH 1400 801-LH 1700
10” 1000-LH 2000 1001-LH 2700
12” 1200-LH 2900 1201-LH 3700
4. As a last resort, when only the basin size is available (only for systems without sweeper piping,
eductors or nozzles)
Calculation: Length x Width x Turn Over Factor (See chart to the right).
Example ~ A basin measuring 10’ wide x 20’ long with average water depth of 9”.
1. 10 x 20 x 5.33 = 1066
2. Filtration fl ow rate of 15% side stream = 1066 x 15% = 160 gpm
Select the Separator size by using the Separator Systems Selection Chart to fi nd a fl ow equal to or
greater than the calculated GPM. Example ~ 160 gpm would use a Series 251.
Depth of
Water
Turn-Over
Factor
6”-24” 5.33
24”-60” 8.33
60”-120” 10.00
Above 120” 12.50
REV. 07/11/12
P & ID
DrainY Separator Skid
P.I.
Cooling tower or Fluid cooler
1 of 1
System Pump
Heat Exchanger (Cooling Tower Only)
Typical Installation P&ID
GLS Clean Sweep
GWS-1187
RevC 07112116
GENERAL WATER SYSTEMS | P. O. Box 444 | Desert Hot Springs | CA 92240 | gwslp.com
ControlPanel
SeparatorOutlet
Pump &MotorBasket
StrainerInlet
Purge
292mm11 1
2 "
1417mm55 3
4 "
1658mm65 5
16 "
1229mm48 3
8 "
1392mm54 13
16 "351mm13 13
16 "
978mm38 1
2 "
1232mm48 1
2 "
THIS DRAWING IS FOR SPATIAL CONSIDERATION ONLY, AND SUBJECT TO CHANGE W/O PREVIOUS NOTICE, DO NOT PRE-PLUMB TO THESE DIMENSIONSGLS
GLS501-HH
*UNLESS OTHERWISE SPECIFIED - ALL DIMENSIONS ARE IN INCHES
REV:7/18/2019 A
DATE:
PREPARED BY:
RELEASED BY:
PAGE: 1JASON WU
BOB KAZANJY
GENERAL WATER SYSTEMS
Page 2 of 16American-Marsh Pumps · 185 Progress Road · Collierville, TN 38017
phone: 800-888-7167 · fax: 901-860-2323 · www.American-Marsh.com
Pump Performance Curve
Customer :Customer reference :Item number : 002Service :Quantity : 1Quote number : 434978 Date last saved : 28 May 2015 4:38 PM
Size : 4x5-8 RECStages : 1Speed, rated : 1,750 rpmBased on curve number : 4x5-8 REEfficiency : 76.33 %Power, rated : 9.92 hpNPSH required : 8.50 ft
Flow, rated : 750.0 USgpmDifferential head / pressure, rated : 40.00 ftFluid density, rated / max : 1.000 / 1.000 SGViscosity : 1.00 cPCq/Ch/Ce/Cn [ANSI/HI 9.6.7-2010] : 1.00 / 1.00 / 1.00 / 1.00
H (60 Hertz Power Only)
hp
SUPPLY VOLTAGE: 460V /3PH/60HZ MOS
PROTECT CIRCUIT AS PER NEC 430-62 L1 e--- - -�+-
l EIW(H (lRWf PROIEClffi PRIMIEI B'f NSTMJ..ER NID Mlfil IIEf UL 489 OR UL I SEE AA ON UL ID SOCKER AS REQIIRED B'f GWS NID UL
MOTOR
l2 e- �0 -4 le e .,.___ ___ � I -� 10 HP FLC 14.00
@----� L3 e-
EQUIP. �D.
� -ill
REMOlE PUMP START C(Jll'ACT BY OTHERS
f---
1 ��+-
-- --�
2A CB 2A (lj
:TI� 400/1'1.fNlf. 250 VA
�D AUTO
11 ♦ I x T 2 I I I
: �-x--�
.. - 0 ..._e----o ,I- -
lw1�
�
EQUf. GRNI.
� -ill I PART# HP FLC
GRZ-10000 0.5 1.00
GRZ-10001 1 1 80
GRZ-10002 15 2 60
GRZ-10003 2 3 40
GRZ-10004 3 4.80
GRZ-10005 5 7.50
GRZ-10006 7.5 11.00
GRZ-10007 10 14.00
GRZ-10008 15 21.00
GRZ-10009 20 27.00
GRZ-10010 25 34.00
CYCLE TIMER GRZ-10011 30 40.00
GRZ-10012 40 52.00
GRZ-10013 50 65.00
GRZ-10014 60 77.00
I • MANUAL PURGE I I 2 7 1 6 �� O<j)<j) NOTE: VN.VE WILL NOT OPEN MIEN PUMP IS OFF
UL FILE 1 E332317 SUPPLY VOLTAGE 4GOV / 3 PHASE/ 60HZ
MAXIMUM FLC: 14 AMPS MOTOR HP: 10 HP
SHORr aRCUIT CURRENT 1 OkA RMS SYMMETRK'>J. 461N MAXIMUM
Notes, All P1ovlng parts to be f'ully guQrded. field teminQl tightening torque 12 lb/Ins. All f'leld wiring 14 A..,G copper PllnlrlUPI, 90' c. Cul. RATED \IIRE, u,... copper conductors only f'or terl'llnQls Intended f'or connection only to copper wire. Broken lines lndlcQ te f'ield wiring.
:��t
�vf���c':.� i:;clt;���lr
,:;;;s
�Qted only.
����:q����lt
N���t
�c
�sf.1H�'}'tT�/li:c��nectlng
�
l �; : � ---'-""' ��-------------0-�1 e � I
Revlslona:
A IIIUIRI I'm lob Name: GRZ-10007-IH-09
TA 01/15/2012 nue,PUMP CONTROL W/PURGE B.AJJ. V� En&tneer:
TECHNICAL DATADIMENSIONS AND WEIGHTS
PARTS LISTITEM DESCRIPTION MATERIAL
1† Body Carbon Steel (ASTM A 216, Grade WCB)2 Basket Stainless Steel (304)3 Gasket Spiral Wound Stainless Steel (304)4 Cover Carbon Steel (ASTM A 216, Grade WCB)5 Pipe Plug Carbon Steel (ASTM A 105)6 Hex Head Cap Screw Carbon Steel (ASTM A 193, Grade B7)7* Knob Steel8* Gasket Buna-N (Max Temperature 200°F)
Style SGFV & SGFV-KBasket Strainer, Flanged
Carbon Steel (ASTM A 216, Grade WCB)
STANDARD SCREENS SUPPLIED
Standard screens supplied are for liquid service, unless otherwise specified.Options: Other meshes, perforations, and screen materials are available.
150# Class
300# Class
150# Class Maximum Pressure
and Temperature Limits
150 PSI at 565F 285 PSI at 100F
300# Class
740 PSI at 100F
PSI]
°F]
°C]
0 100 200 300 400 500 600 700 800 900 1000 1100 12000
100
200
300
400
500
600
700
800
Maximum Pressure and Temperature Limits
300 PSI at 838F
38 93 149 204 260 316 371 427 482 538 593
690
4828
1379
2069
2759
3449
4138
5518649
Pres
sure
[
Temperature [
Temperature [
Pressure [KPa ]
All Sizes 2" thru 14" Sizes 2" thru 14"
PRESSURE vs. TEMPERATURE CHART150# & 300# Flanged Carbon Steel (ASTM A 216, Grade WCB)
For use with Bolted Cover Only
*In Accordance with ASME B16.5
*Denotes parts for the Style SGFV-K 150 lb. class only.†Optional Body Materials Available in LCB, WC6, and WC9.
SIZE SCREENGAGE
SCREEN PERFORATIONFOR STEAM OPEN
AREAFOR LIQUID OPEN
AREAin mm in mm in mm1-1/2 to 3 40 to 80 22 3/64 1.2 33% 1/16 1.6 30%
4 to 14 100 to 350 22 1/16 1.6 30% 1/8 3.2 43%
WEIGHTSSize 1-1/2” 2” 2-1/2” 3” 4” 5” 6” 8” 10” 12” 14”
150 lbs 22 30 35 39 69 110 125 270 360 450 1550kgs 10 14 16 18 31 50 57 122 163 204 703
300 lbs 24 32 42 56 88 126 150 295 420 500 1650kgs 11 15 19 25 40 57 68 134 191 227 748
Certified dimensional drawings are available upon request.†This table reflects only the nearest metric equivalents.
SIZEDIMENSIONS
A B C E150# 300# 150# 300# 150# 300# 150# 300#
in mm in mm in mm in mm in mm in mm in mm in mm in mm1-1/2 40 6-1/2 165 7 178 4-1/2 114 4 102 4 102 3-3/4 95 1/2 15 1/2 15
2 50 8-1/2 216 8-13/16 224 5-7/8 149 4-3/4 121 4-3/4 121 3-3/4 95 1/2 15 1 252-1/2 65 8 203 9 229 5-7/16 138 5-5/8 143 4-1/4 108 4-5/8 117 3/4 20 1 25
80 - 222 10-1/16 256 5-11 1 144 5-11/16 144 5-5 143 5-5/8 143 20 3/4 204 100 11-3/16 284 12 305 8-1/4 210 8-1/4 210 6-1/16 154 6-1/16 154 1 25 1 255 125 12-1/4 311 13-1/8 333 10-1/4 260 10-1/4 260 5-5/8 143 5-5/8 143 1 25 1 256 150 13-7/8 352 15-9/16 395 12-13/64 310 12-13/64 310 6-5/16 149 6-5/16 160 1-1/4 32 1-1/4 328 200 17-3/8 441 18-7/8 479 15-9/16 395 15-9/16 395 8-3/16 208 8-3/16 208 1-1/2 40 1-1/4 40
10 250 22 559 21-5/16 541 16 406 14-3/8 365 10-3/8 264 9-7/8 251 1-1/2 40 2 5012 300 25 635 25-3/8 645 23-3/4 603 23-3/4 603 12-3/8 314 12-3/8 314 2 50 2 5014 350 34-5/16 871 34-5/16 871 28 711 34-3/8 873 16-1/2 419 20-3/16 513 2 50 2 50
Size (in2) Size (in2) Size (in2) Size (in2)1-1/2” 20.10 3” 54.53 6” 215.65 12” 1141.87
2” 53.42 4” 117.94 8” 401.76 14” 1200.002-1/2” 45.72 5” 129.00 10” 591.73
TOTAL SCREEN AREA (150 LB.)
Size Cv Size Cv Size Cv Size Cv1-1/2” 32 3” 120.2 6” 743.1 12” 4980.6
2” 42.7 4” 276.7 8” 1486.3 14” 7600.02-1/2” 84 5” 442.7 10” 3051.6
FLOW COEFFICIENTS
*See DETERMINING RATIOS on page S5 of the Strainer InformationSection for calculating NET FREE AREA of the screen to inside pipe area.
GWS-1008 Rev A5-1-2017
ffiAS D & S SERIES Butterfly Valves
Features & Benefits
D Series Lug/Wafer-Style Ductile Iron Body
Stem retainer plate ensures
bla.vout protection.
for low p-essure media.
NSF/ANSI 372
*For sizes larger than 24", please consult MAS
Durable and economical.
-
DRIVE STEffi
EXTEnDED nECH Allows use with
insulated pipes,
-
Secondary c>ring stem seal protection.
SEAT
BACHlnGRlnG Rigid backing ring allows for
dead-end service.
-
as standard
2
Features & Benefits
• Sizes 2" through 24" available from stock, wafer or lug
• lug-style dead end service capabilities through 12":
200 PSI uni-directional
100 PSI bi-directional
• Install between Standard ANSI class 125 /150 flanges
• ISO 5211 square drive shaft for easy automation
• Conforms to MSS-SP-67, MSS-SP-25, APl-609
• Designed for blowout-proof service
• High-Cv slim disc & 2-piece stem design 2"-12"
• Field repairable
• Vacuum service capable 2" thru 12" to 10 microns
• Dead end service for S-Series coming in 2014
ffiAS D SERIES Butterfly Valves 2"-12"
D Series Exploded View
-@ r------====-=-=-:---==-----J@
=----------©
4
D Series
Item Description Materials
1 Body Ductile Iron ASTM A536
2 Stem Retainer Carbon Steel, Plated
3 Seat See Pg 3 or 18
4 Stem Retainer Carbon Steel, Plated Screws
5 Upper Stem Stainless Steel ASTM A582,
Alloy 416
6 Disc See Pg 3
7 Lower Stem Stainless Steel ASTM A582, Alloy 416
8 Lower Stem
Carbon Steel, Plated Retainer
9 Bushing PTFE/Graphite
10 O-Ring EPDM, BUNA-N, FI uoroelastomer
11* Locking Arm* Carbon Steel, Plated
12* Infinite Lever* Carbon Steel, Plated Plate
13 Lever Handle Stamped Steel, Epoxy Coated
{Standard)
14 Throttle Plate Carbon Steel, Plated
{Standard)
15 Bolt Carbon Steel, Plated
16 Nameplate Tag Aluminum
*Optional accessory. It is important to note that the infinite lever plate and locking arm is only lockable in the full open or full closed positions.
LowerStem Detail
www.mastewart.com
\
ffiAS D SERIES Butterfly Valves 14"-24"
D Series Exploded View
J Ii •-----0 -----:.-------j0
I I sa
�
I
DSeries
Item Description Materials
1 Body Ductile Iron ASTM A536
2 Stem Retainer Carbon Steel, Plated
3 Seat See Pg 3 or 18
4 Stem Retainer
Carbon Steel, Plated Screws
5 Upper Stem Stainless Steel ASTM A582, Alloy 416 or 410
6 Disc See Pg 3
7 Lower Stem Stainless Steel ASTM A582,
Alloy 416 or 410
8a Lower Stem Ductile Iron ASTM A536 Retainer
Lower Stem 8b Retainer Bolts Carbon Steel, Plated
and Washers
9 Bushing PTFE/Graphite
10 0-Ring EPDM, BUNA-N, Fluoroelastomer
Lower Stem Detail
www.mastewart.com
ffiAS D & S SERIES Butterfly Valves
Torque & Service Factor Ratings
D SERIES Valve Seating Torques (in-lbs)
2 105 111 117
2½ 133 143 159
3 191 203 218
4 283 316 343
5 428 479 540
6 636 720 799
8 1239 1273 1411
10 2567 2710 2832
12 3153 3307 3671
14 3858 4138 4337
16 5413 6027 7466
18 6833 8121 10089
124
184
247
373
631
909
1505
3105
4305
200
330
440
820
1150
2400
Consult
Manufacturer ------11--------1----
20 9820 10527 13367
24 15909 17005 21041
The torque values listed above do not include a safety factor. It is recommended that a safety factor of 20% be added to these numbers for standard self-lubricating service. For water, dry air, solvents, abrasives, powder, and dust service, see service factor guide chart below.
Cartridge-style seats pr0111de
superior performance to booted
ormolded seats.
Service Factor Rating Service Condition Service Type
1 Ideal
2 Normal
3 Severe
4 Extreme
Z' Thru IZ' Full Vaaium
to 10 microns
Media Type
Lubricating Oil
Water
Dry Air, Solvents
Abrasives
l For PE Seats (PTFE over EPDM) used in D Series, follow torques as shown in S Series.
S SERIES Valve Seating Torques (in-lbs)
STANDARD SEAT (code B,E,V, etc)
Size Pressure Differential (L1P in PSI)
(in) 50 ll.P 100 ll.P 150 ll.P 200 ll.P
2 105 111 117 124
2½ 133 143 159 184
3 191 203 218 247
4 283 316 343 373
5 428 479 540 631
6 636 720 799 909
8 1239 1273 1411 1505
10 2567 2710 2832 3105
12 3153 3307 3671 4305
14 3858 4138 4337 -
16 5413 6027 7466 -
18 6833 8121 10090 -
20 9820 10527 13367 -
24 15909 17005 21041 -
Safety Factor Multiplier
20% 1.20
30% 1.30
50% 1.50
100% 2.00
12
PTFE SEAT (code PE)
Pressure Differential (L1P in PSI)
50 ll.P 100 ll.P 150 ll.P
144 148 150
161 165 168
299 304 310
392 409 425
771 793 814
1074 1113 1151
2106 2177 2257
3151 3301 3452
4186 4443 4691
Consult Manufacturer
This service factor chart is a suggested guide only. Actual service ronditions will vary due to dynamic flow conditions and may require adjustments to the applied safety factor.
D SERIES Cv Values Valve Sizing CoefficientstuS-GPm,�Pl
1½ 99 76 59 41 32
2 132 120 86 58 42
2½ 256 202 142 98 65
3 505 392 198 125 86
4 936 702 401 232 140
5 1109 922 625 392 232
6 2531 2009 1105 611 372
8 4812 3555 1901 1211 726
10 7498 6183 3740 2065 1232
12 9928 8805 5905 3178 1909
14 12915 10854 7220 4560 2771
16 16626 14961 9909 6289 3780
18 23705 19743 13178 8325 5029
20 27915 25396 16928 10698 6468
24 43212 39206 26128 16550 9807
The valve sizing coefficient is referred ro as •c v• and is rhe rare of warer flow in gallons per minute (GPM) through a given opening ar a pressure drop (LlP) of 1 PSI ar standard room remperarure. The recommended angle of opening for valve sizing is berween 50° and 70° open.
D SERIES Testing Specifications
200 PSI*
300 PSI
220 PSI
150 PSI
225 PSI
165 PSI
*PTFE seats are rated ro 150 PSI
150 PSI
225 PSI
165 PSI
16
22
37
38
77
132
203
401
695
1065
1554
2133
2822
3623
5567
7
11
20
21
35
62
96
191
321
495
712
980
1301
1678
2521
I
ffiAS D SERIES Butterfly Valves
CV Values & Testing Spees
1.8
2
4
8
14
29
42
65
151
234
338
460
613
790 12
860 21
·o('��s ('�o .>l
'\<Y S'<:--0
o�<o <?.'-�'<.e �
s'<-�� -£:>.e
'\'<:>-<o
www.mastewart.com
ffiAS D SERIES Butterfly Valves
D Series Dimensions
ffiAS D SERIES-Ductile Iron
1 DN35 1.3 33 1.4 36 110.
2 DN50 1.7 43 1.8 46 4.75 120.7 4 x 'l•-11 UNC
2½ DN65 1.8 46 2.3 58 5.50 139.7 4 x '!.-11 UNC
3 DN75 1.8 46 2.9 74 6.00 152.4 4 x '/•-11 UNC
4 DNlOO 2.0 52 3.8 98 7.50 190.5 8 x '/•-11 UNC
5 DN125 2.2 56 4.5 115 8.50 215.9 8 x 'I, -10 UNC
6 DN150 2.2 56 5.8 148 9.50 241.3 8 x '/, -10 UNC
8 DN200 2.4 60 7.7 195 11.75 298.5 8 x 'I, -10 UNC
DN250 2.7 68 9.5 4 . 5 362.0 X 7/,-9 U
12 DN300 3.1 78 11.7 297 17.00 431.8 12 x 7/, -9 UNC
14 DN350 3.1 78 18.75 476.3 12 x 1-8 UNC
16 DN400 4.0 102 21.25 539.8 16xl-8UNC
18 DN450 4.5 114 22.75 577.9 16 x 1 1/,-7 UNC
20 DN500 5.0 127 25.00 635.0 20 x 1 '/•-7 UNC
24 DN600 6.1 154 9.50 749.3 20 xl 1/, -7 UNC
n-0h
0.7 4x 18
4x 0.9 4x 22
4 x0.7 4x 18
4 X 0.7 4X 18
4 X 0.7 4x 18
4 X 0.9 4x 22
4 X 0.9 4x 22
4 X 1.0 4x 26
X 1.0 4x 26
4 X 1.0 4x 26
r-
mounting Flange
Dimensions
Size
F0S
F07
FlO
F14
F16
Bolt Circle Diameter (in)
1.97
2.76
4.02
5.51
6.50
Hole Size (mm)
4x7
4x10
4x12
4x18
4x22
2.5
2.6
3.2
3.5
4.3
4.8
5.4
6.7
7.9
9.3
10.3
11.8
12.8
14.2
16.5
14
64 .9 12 .1 30 0.35 9 .969 50 F05
66 5.1 130 1.18 30 0.354 9 1.969 50 FOS 4.2 1.9 5.2 2.4
81 5.6 142 1.18 30 0.354 9 1.969 50 F05 5.5 2.5 6.5 3.0
89 5.8 147 1.18 30 0.354 9 1.969 50 FOS 6.1 2.8 7.3 3.3
109 6.7 170 1.18 30 0.433 11 2.756 70 F07 9.0 4.1 12.5 5.7
122 7.4 188 1.18 30 0.551 14 2.756 70 F07 12.6 5.7 16.9 7.7
137 8.0 203 1.18 30 0.551 14 2.756 70 F07 15.1 6.9 20.4 9.3
170 9.4 239 1.57 40 0.669 17 4.016 102 Flo 27.0 12.3 33.3 15.1
01 10.7 7 .57 0.866 2 4. 16 102 10 0.8 18.5 54.5 24.7
236 12.0 305 1.57 40 0.866 22 4.016 102 Flo 60.7 27.6 76.2 34.6
262 13.0 330 1.57 40 0.866 22 4.016 102 Flo 86.9 39.4 131.5 59.7
300 14.2 361 2.00 51 1.063 27 5.512 140 F14 121.4 55.1 194.8 88.4
325 15.6 396 2.00 51 1.063 27 5.512 140 F14 154.2 69.9 235.5 106.8
361 17.3 439 2.52 64 1.063 27 6.496 165 F16 208.5 94.6 340.5 154.4
9 19.7 500 2.76 70 1.417 36 6.496 165 Fl6 387.9 76.0 503.0 228.2
Standard 10-Position
Throttle Plate
H2 H3
ISO Mounting Pad
n-Th
J
D SERIES Handle
Dimensions
HANDLE 220.01
HANDLE 260--01
HANDLE 260--02
HANDLE 360--01
HANDLE 360-02
0
---------l
®
j
2•-3• DN50-75
4• DNlOO
5"-6" DN125-150
8"* DN200*
10•-12•• DN250-300*
0.88
1.00
1.00
1.25
1.25
I
22.4 0.354 9.0 1.25 31.8 8.7
25.4 0.433 11.0 1.38 35.1 10.2
25.4 0.433 14.0 1.38 35.1 10.2
31.8 0.669 17.0 1.75 44.5 14.2
31.8 0.669 22.0 1.75 44.5 14.2
*Recommended operation with a gear operator or an actuator for sizes 8"-12"
220 9 229 1.0 25.4 1.0 0.5
260 12 305 1.1 27.9 2.0 0.9
260 12 305 1.1 27.9 2.0 0.9
360 14 356 1.4 35.6 3.0 1.4
360 14 356 1.4 35.6 3.0 1.4
Locking arm Infinite Lever Plate
I Over-Travel on Infinite 2-Position Lock Option Allows Disc to
The standard 10-position throttle plate has grooves thar allow rhe handle ro snap in place for repeatabiliry and ro prevent unintentional movement of the disc.
�Wipe Seat
For even more control, Infinite Lever Plates (ILP) and arms are available, which allow the valve to be fixed in place wirh a bolr at any position. /r is important to
nore char the ILP plates and locking arms can be padlocked in the full open and full closed positions only. to prevent tampering or accidental operation.
Gear Operator Padlocked Closed Infinite Lever Details
\Lf>ShoWnDN50-65 ao\.ted in an �
\ntermediate 3 DN75 01 02
position 4 DNlO0 02 03
5-6 DN125-150 02 04
8* DN200* 03 05
10-12* DN250-300* 03 06
Gear Operator Dimensions
1.5-3 3 3. 6 152 2.8 1330 150
4 DNlO0 1.7 43 3.2 6 152 2.8 .3 1330 150
5-6 DN125-150 MAS-GO-02-15O 2.5 64 3.6 91 6 152 5.6 2.5 2200 250
8 DN200 MA5-GO-03A-l5O 2.4 61 4.7 119 10 254 11.5 5.2 4425 500
10 DN250 MAS-G0-03B-15O 2.4 61 4.7 119 10 254 11.5 5.2 4425 500
1 -1 DN3 0-35 5-GO-04- 50 2.6 6 .5 165 12 305 22.2 10.1 885 1000
16-18 DN400-450 MAS-GO-05-15O 3.5 89 7.9 201 16 406 40.8 18.5 15900 1800
20 DN500 MAS-GO-06-15O 5.0 127 10.1 257 16 406 78.1 35.4 30090 3400
24 DN600 MAS-GO-07-15O 6.1 155 12.4 315 16 406 101 45.8 39825 4500 .. , ) I Af.'4.3'-'tl.#I-LU..
..:J--/.7 www.mastewart.com
ffiAS D & S SERIES Butterfly Valves
Seat Material Guide
Black BUNA (Code B)
Black EPDM {Code E}
White EPDM
EPDM Food Grade (Phenolic Backing) (Code WEF)
Black EPDM Food Grade {Code BEF)
High Temperature High Temp EPDM EPDM
(Phenolic Backing) (Code HT)
Chlorosulfonated Synthetic Rubber (Code SR)
(CSM) (Phenolic Backing)
Silicone (Code SL)
(Phenolic Backing)
FI uoroelastomer (FKM-VITON) (Code V)
(Aluminum Badcing)
Neoprene (CR) (Code NP) (Phenolic Backing)
Wear Resistant EPDM (Code WR)
(Phenolic Backing)
PTFE Over EPDM (Phenolic Backing) (Code PE) R.,t,,J ro J'iO PSI
Hydrocarbons with less than 10°F to 180°F
40% of aromatics, Natural Solvents, Benzene, Xylene
Gas, Air, H2O, Sea Water, Brine, Alcohols, Glycols -12°C to 82°C
-4°F to 275°F
H2O, Saturated Steam*, Air, Brine, Abrasives,
Phosphates, Esters, Ketones, -20°C to 135°C Alkali, Food Compounds,
Liquids and Solids, Dilute Hydrocarbons, Oils, Inorganic Acids, Caustic Fats, Dry Air
Soda
( •tow pressure sarurared sream -4°F to 302°F only. Please consu/r MAS for
derails.)
-20°c to 1so0c
Oxidizing Acids, Chromic 0°F to 275°F
Acid, Hydrofluoric Acid, Steam, Ketones, Sulphur Based Acids, Hot Air, Nitric Acid
Sodium Hypochlorite, Ozone -18°C to 135°C
-22°F to 400°F
Beverages, Food Hydrocarbons,
Solvents, Steam
-30°C to 204°C
Hydrocarbons with high concentration of aromatics, 0°F to 392°F
Mineral and Halogenated Steam, Ketones, Amines, Acids, Phosphoric Acid, Esters, Alkali Aliphatic and Aromatic -1s0c to 200°c
Ethers
20°F to 200°F
Oils, Dilute Mineral Acids, Ketones, Concentrated Acids, Alkali, Fats Solvents for Paint
-7°C to 93°C
14°F to 250°F
Abrasive Products Steam, Hydrocarbons, Oils
-10°C to 120°c
-4°F to 250°F
Corrosive Products, Abrasive Products, Fluorine Solvents Gases, Alkaline Metals
-20°C to 120°c
18
SERIES
5602
5603
Features
Direct mount ISO5211 Full Port stainless steel ball valve
Highly visible LED light gives continuous status indication
Industrial weatherproof actuator, UV protected
Multi-voltage capable with auto-voltage sensing
Electronic torque limiter - protects against valve jams
Anti-condensation heater
Manual override with visual valve position indicator
Electrical connections via external DIN plugs, no need to re-move the cover
Two dry contact auxiliary limit switches used to confirm valve
open/closed position
Triple RTFE/Viton live loaded stem seals, adjustable
Applications
On-off control of water, air, oil and other media compatible with the materials of construction. Steam service up to 25 PSI with optional high temperature mounting bracket. Suitable for vacuum service up to 29”Hg. Actuator designed for 75% duty cycle.
Construction
Description
Electric actuated valve uses power-to-open and power-to-close, stays in the last known position with power failure. On receipt of a continuous voltage signal, the motor runs and via a flat gear system rotates the ball 90º. The motor is automatically stopped by inter-nal cams striking limit switches. On receipt of a reversing continuous signal, the motor turns in the opposite direction reversing the valve position. Power connection (3-wire+ground) via large external gray DIN plug connector with built-in screw terminals (included).
Operation
Optional Functions
BSR - Battery Spring Return Kit - actuator fails to a safe position with loss of power DPS - Digital Positioning System - valve position controlled by 4-20mA or 0-10V control signal
Doc: 5602.5603.0611 Cornelius, N.C. • USA www.valworx.com
Electric Actuated Ball Valve 2-way Stainless Steel, Full Port
1/4” to 2” NPT
Pressure-Temperature*
Pressure Rating: 1000 PSI (69 Bar)
Working Temperature: 0 to 158º F (-18 to 70º C)Media temperatures up to 266º F (130º C)
with optional high temp. mounting bracket
Ball Valve Temperature Rating: 0 to 356º F (-18 to 180º C)
Actuator Temperature Rating: -4 to +158º F (-18 to 70º C)
*See P/T chart
Valve Body 316 stainless steel ASTM A351 CF8M
Ball 316 stainless steel CF8M
Ball Seats RTFE (reinforced Teflon)
Stem Seals RTFE (reinforced Teflon)/ Viton
Stem 316 stainless steel
Actuator Enclosure Anti-corrosive Polyamide
Position Indicator Glass filled Polyamide
Fasteners Stainless Steel
Investment cast 2-piece full port stainless steel body/ball for unrestricted flow and mini-mum pressure loss. Adjustable live loaded stem seal packing helps compensate for wear, pressure or temperature fluctuations, extending the cycle life of the valve. Blow-out proof stem. Standard corrosion resistant elec-tric actuator includes a manual override, auxil-iary valve position confirmation switches, anti-condensation heater, and electronic torque protection.
SERIES
5602
5603
Doc: 5602.5603.0611 Cornelius, N.C. • USA www.valworx.com
Specifications (English units)
Stock
Number
Pipe Size
(NPT)
Orifice Size
(inch)
Cv Flow
Factor
Pressure
Max.(PSI)*
Cycle Time
/90º (seconds)
Enclosure
Rating
Max. Current Draw (Amps)
115VAC 240VAC 24VAC 12VDC 24VDC
HIGH VOLTAGE: 85-240v AC or DC
560202 1/4 0.45 8 1000 11 IP65 0.17 0.09 - - -
560203 3/8 0.49 10 1000 11 IP65 0.17 0.09 - - -
560204 1/2 0.59 15 1000 11 IP65 0.17 0.09 - - -
560206 3/4 0.79 35 1000 11 IP65 0.17 0.09 - - -
560208 1 1.00 60 1000 11 IP65 0.17 0.09 - - -
560210 1-1/4 1.25 90 1000 14 IP67 0.24 0.11 - - -
560212 1-1/2 1.50 125 1000 14 IP67 0.24 0.11 - - -
560216 2 2.00 240 1000 14 IP67 0.24 0.11 - - -
LOW VOLTAGE: 12-24v AC or DC
560302 1/4 0.45 8 1000 12 IP65 - - 0.85 2.05 1.00
560303 3/8 0.49 10 1000 12 IP65 - - 0.85 2.05 1.00
560304 1/2 0.59 15 1000 12 IP65 - - 0.85 2.05 1.00
560306 3/4 0.79 35 1000 12 IP65 - - 0.85 2.05 1.00
560308 1 1.00 60 1000 12 IP65 - - 0.85 2.05 1.00
560310 1-1/4 1.25 90 1000 16 IP67 - - 1.20 3.08 1.40
560312 1-1/2 1.50 125 1000 16 IP67 - - 1.20 3.08 1.40
560316 2 2.00 240 1000 16 IP67 - - 1.20 3.08 1.40
Cv is the GPM of water at 60º F that will pass through the valve with 1 PSI pressure drop
* Pressure @ 100º F (see P/T chart)
Pressure/Temperature Chart (PSI/ºF)
P/T Chart
PSI 1000 1000 1000 950 875 750
ºF 0 50 100 158 200 266
Notes:
1. Standard working temperature of valve assembly: 0 to 158º F
2. Media temperatures up to 266º F with optional high temperature mounting kit.
Doc: 5602.5603.0611 Cornelius, N.C. • USA www.valworx.com
Dimensions:
SERIES
5602
5603
Pipe Size (NPT) A B C D F J K P Weight
1/4 inch 2.57 6.97 7.32 4.33 7.99 1.46 1.22 0.45 4.9 lb
mm 65.3 177 186 110 203 37 31.0 11.5 2.2 kg
3/8 inch 2.57 6.97 7.32 4.33 7.99 1.46 1.22 0.49 4.8 lb
mm 65.3 177 186 110 203 37 31.0 12.5 2.2 kg
1/2 inch 2.57 6.97 7.32 4.33 7.99 1.46 1.22 0.59 4.85 lb
mm 65.3 177 186 110 203 37 31.0 15 2.2 kg
3/4 inch 3.04 6.97 7.64 4.33 8.50 1.77 1.52 0.79 5.2 lb
mm 77.3 177 194 110 216 45 38.7 20 2.4 kg
1 inch 3.49 6.97 7.99 4.33 8.98 2.11 1.72 0.98 5.9 lb
mm 88.7 177 203 110 228 53.5 43.8 25 2.7 kg
1-1/4 inch 4.03 6.97 10.04 4.33 11.34 2.32 2.00 1.26 8.2 lb
mm 102 177 255 110 288 59 50.7 32 3.7 kg
1-1/2 inch 4.29 6.97 10.67 4.33 12.13 2.94 2.17 1.50 9.8 lb
mm 109 177 271 110 308 74.8 55.0 38 4.5 kg
2 inch 4.93 6.97 11.02 4.33 12.87 3.29 2.41 1.97 12.1 lb
mm 125 177 280 110 327 83.5 61.3 50 5.5kg
B
F
C
J
A
K
D
ØP NPT
7
LIQUID FILLED GAUGE2½” Dial - Brass Wetted Parts
±3-2-3% Accuracy
General Specifications
CASE: Stainless steel.
RING: Crimped stainless steel.
LENS: Acrylic.
DIAL: Aluminum, white finished with black markings.
POINTER: Aluminum, black, non-adjustable.
MOVEMENT: Brass with precision-milled teeth.
TUBE & SOCKET: Brass.
CONNECTION: See table below.
ACCURACY: ±3-2-3% (ASME B40.100 Grade B).
PROCESS TEMPERATURE: 0 to 140°F (-18 to 60°C).
AMBIENT TEMPERATURE: 0 to 140°F (-18 to 60°C).
Standard Ranges
To Order
P L F 2 5 9 8 L 0 4Model Number Range Code
Dimensions (in.)
edoC egnaRisp rab
.giF .viD .giF .viD
100 rab&0-gH"03 5 1 2.0 20.0
200 rab&isp51-0-gH"03 5 5.0 5.0 50.0
300 rab&isp03-0-gH"03 01 1 5.0 1.0
400 rab&isp06-0-gH"03 01 2 1 1.0
500 rab&isp001-0-gH"03 02 2 1 2.0
600 rab&isp051-0-gH"03 52 5 2 2.0
800 rab&isp003-0-gH"03 05 01 02 5.0
20 rab&isp51-0 5.2 5.0 2.0 20.0
30 rab&isp03-0 5 1 5.0 50.0
40 rab&isp06-0 01 2 1 1.0
50 rab&isp001-0 02 2 1 2.0
60 rab&isp061-0 04 5 2 2.0
70 rab&isp002-0 05 5 2 5.0
80 rab&isp003-0 05 01 5 5.0
90 rab&isp004-0 001 01 4 1
01 rab&isp006-0 001 02 01 1
11 rab&isp0001-0 002 02 01 2
91 rab&isp0051-0 003 02 02 5
21 rab&isp0002-0 005 05 02 5
31 rab&isp0003-0 005 001 05 5
41 rab&isp0005-0 0001 001 05 01
The Miljoco Models PLF2598L and PLF2598 are rugged
& durable and suited for a wide variety of commercial
and general service applications. The stainless steel
case is filled with glycerine to protect the internals
against vibration and pulsation. This unit is completely
weather-proof and excellent for pumps, air compressors,
irrigation systems, and other installations suitable for
brass process connections. CAUTION: A coil syphon must
be installed on the connection when used on steam
applications.
ledoM eziSlaiD teltuO .nnoC
L8952FLP "½2 mottoB TPN"4/1
8952FLP "½2 kcaB TPN"4/1
.yrotcaftlusnoc-elbaliavaebyamselytsesacrehtO
Models
PLF2598L
enera Water Systems
1. Limited Warranty ‐‐‐ a Water Systems (“GWS”) warrants its products to be free from
defects in material and workmanship as indicated below:a. GWS warrants Separators Vessels for a period of 6
the date of shipment.b. Except as set forth herein, GWS warrants all other products, including Electronic
Water Treatment Equipment, pump control panels and system components, for a period of 12 months from the date of install or 16 months from the date of shipment, whichever occurs first.
. GWS will transfer and assign to the customer any extended warranties provided by the original equipment manufacturer for GWS purchased items (GWS‐1122).
. Notwithstanding the limited warranty herein, pump seals, filter bags and other normal wear items and products are not covered under this limited warranty.
2. Extent of Limited Warranty ‐‐‐ GWS’ sole responsibility for malfunctions and defects in product(s) is limited to repair and replacement, as set forth in this limited warranty statement.
a. This limited warranty does not cover incidental or consequential damages, injuries, loss of revenue, failure to realize savings or other costs resulting from defective product(s).
b. This limited warranty does not cover any costs relating to removal or replacement of any GWS supplied system or component or any other charges associated with said removal or replacement.
. This limited warranty does not cover damages due to external causes, including, but not limited to, improper use, problems with electrical power, accident, neglect, alteration, repair, improper installation, static discharge or improper testing.
. This limited warranty shall be null and void if any modifications or additionsare made to any GWS product or system without written factory approval.
. Return shipping costs to GWS or any original equipment manufacturer are the customer’s responsibility.
. Fitness of Use – THE WARRANTIES HEREIN ARE EXCLUSIVE AND NO OTHER WARRANTY OR CONDITION, WHETHER WRITTEN OR ORAL, IS EXPRESSED OR IMPLIED AND GWS
GWS-1144 Rev B
Limited Warranty May 2020
5. SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OR CONDITIONS OFMERCHANTABILITY, SATISFACTORY QUALITY, AND FITNESS FOR A PARTICULARPURPOSE.
6. Damages ‐‐‐ This limited warranty does not apply to products, damages or injuriesresulting from misuse, neglect, normal expected wear, corrosion, improper installation,modifications, alterations, tampering or operation contrary to GWS or an originalequipment manufacturer’s recommendations. THE REMEDIES IN THIS WARRANTY ARECUSTOMER’S SOLE AND EXCLUSIVE REMEDIES.
7. RMA Required – Before sending any item to GWS for warranty repair orreplacement, a Return Material Authorization (RMA) number must be obtained fromGWS.
a. This number needs to be placed on the address label and the packing slip in orderto assure proper credit is issued.
b. Ship defective unit, freight prepaid, to GWS, ATTENTION RMA# , 1525 E. 6thSt., Corona, CA 92879.
8. Inspection ‐‐‐ Upon inspection of the product at GWS’ facility in Corona, California withinthe warranty period, if the defective material is determined to be covered under thislimited warranty, GWS shall repair or replace the defective material at no additional costto the customer.
9. Repairs & Replacements ‐‐‐ GWS has the option, at its sole discretion, to either repairor replace defective items with either new or remanufactured components.Warranty replacement or repair shall not extend the original warranty period.
10. Shipping Damage – All products are shipped F.O.B. factory. Damage to a unit duringshipping must be claimed at the time of product receipt and noted on the bill of ladingbefore signing. Any and all shipping damages are the responsibility of the freightcompany and not the obligation or responsibility of GWS.
11. Shipment of Replacement Parts and Units ‐‐‐ The customer must provide GWS with aPurchase Order for replacement units. When received by GWS, the returned unit willbe inspected.
a. If the defective unit is determined to be covered under this limitedwarranty, a credit for the cost of the replacement unit will be made.
b. If the defect is not a covered defect, the replacement unit will be invoiced inaccordance with the Purchase Order. The customer can request the unit bereturned to the customer. Shipping charges will be the responsibility of thecustomer.
GWS-1144 Rev BGWS-1144 Rev B